PIC18F96J60T-I/PT - 64KB 8-Bit PIC MCU with Ethernet | Microchip
Teilenummer: PIC18F96J60T-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $13.5 | $13,50 |
| 10 | $12.2 | $122,00 |
| 100 | $10.85 | $1.085,00 |
| 500 | $9.65 | $4.825,00 |
| 1.000 | $8.8 | $8.800,00 |
PIC18F96J60T-I/PT Übersicht
An 8-bit microcontroller (MCU) is a programmable processor built around an 8-bit data path, commonly used in embedded systems for sensing, control, and human-interface tasks. PIC18 microcontrollers from Microchip Technology extend the baseline PIC16 architecture with 16-bit instructions, linear memory, and C-optimized peripherals. The PIC18F96J60 family sits in the PIC18J sub-family and adds an integrated Ethernet peripheral, making it a member of the broader power-mics microcontroller hierarchy: PIC18F96J60 -> PIC18J -> PIC18 -> 8-bit MCU -> microcontroller -> integrated circuit.
Key features include 64 KB of self-programmable Flash, 3808 bytes of RAM, 70 digital I/O pins, 16 channels of 10-bit ADC, two MSSP ports for SPI/I2C, two enhanced USART modules, a 16-bit timer/counter bank, and a 10BASE-T Ethernet MAC with on-chip PHY interface. The internal oscillator block supports software-tunable clocking, eliminating external crystals in many designs and reducing BOM cost. The wide I/O count and rich peripheral mix suit gateway, monitoring, and appliance-class networking products.
Technically, the device uses a 16-bit modified Harvard architecture with an 8-level hardware stack, two 8-bit working registers, and a hardware multiply unit. The integrated MAC follows IEEE 802.3 with full/half-duplex support, MAC address filtering, and DMA-assisted frame handling to offload buffer movement from the CPU. CIP (code-protection) and a unique device ID provide IP security, while the In-Circuit Serial Programming (ICSP) interface enables field upgrades.
Typical applications include industrial Ethernet nodes, building automation controllers, remote sensor gateways, smart meters, and appliance networking modules that need low-cost internet connectivity. The integrated MAC and on-chip PHY interface lower the bill of materials versus MCU + external MAC solutions. Designers should provide adequate bulk decoupling near the VDD pins and follow Microchip AN871 application-note layout practices for the Ethernet differential pair to meet IEEE 802.3 emissions targets. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides.
Drop-in-Alternativen für PIC18F96J60T-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC18F96J60T-I/PT (gleiche Bauform und Footprint) – abweichend in Package, Operating Temperature, ADC, Core, Integrated Ethernet.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC18F96J60-I/PT
✅ Drop-In✓ Auf Lager
$4.97 / Stück
Datenblatt ansehen →PIC18F97J60T-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC18F96J60T-I/PF
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$6.2 / Stück
Datenblatt ansehen →PIC18F86J60T-I/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$6.04 / Stück
Datenblatt ansehen →PIC18F96J60T-I/PT Grenzwerte & elektrische Eigenschaften
| Core | PIC 8-bit |
| Series | PIC 18J |
| Program Memory Size | 64 KB (32K x 16) Flash |
| RAM Size | 3808 bytes |
| Maximale Taktfrequenz | 41.667 MHz |
| Betriebsversorgungsspannung | 2.0 V to 3.6 V |
| Number of I/O Pins | 70 |
| ADC | 10-bit, 16 channels |
| Gehäuse | 100-pin TQFP (12x12 mm) |
| Montageart | Surface Mount |
| Packaging | Tray |
| Integrated Connectivity | Ethernet MAC/PHY, SPI, I2C, UART/USART, EBI/EMI |
| Oscillator Type | Internal |
| Betriebstemperatur | -40C to +85C |
| RoHS-Status | Compliant |
PIC18F96J60T-I/PT Pin-Konfiguration
| Pin 1 | RF5 — Digital I/O pin 5 on PORTF |
| Pin 12 | AVDD — Analog VDD supply |
| Pin 13 | AVSS — Analog VSS ground |
| Pin 21 | MCLR — Master clear reset / ICSP programming voltage |
| Pin 34 | TPO+ — Ethernet transmit plus (differential) |
| Pin 35 | TPO- — Ethernet transmit minus (differential) |
| Pin 36 | TPI+ — Ethernet receive plus (differential) |
| Pin 37 | TPI- — Ethernet receive minus (differential) |
| Pin 38 | VDD — Digital supply |
| Pin 45 | VSS — Digital ground |
| Pin 55 | ICSCLK — ICSP serial clock |
| Pin 56 | ICSDAT — ICSP serial data |
| Pin 67 | OSC1 — Oscillator input / external crystal |
| Pin 68 | OSC2 — Oscillator output / external crystal |
| Pin 100 | VDD — Digital supply |
Typische Anwendungen
PIC18F96J60T-I/PT ist geeignet für 6 Anwendungs: Industrial Ethernet Sensor Node, Building Automation Controller, Remote Sensor Gateway, Smart Meter / Utility Endpoint, Appliance Networking Module, Embedded Web-Server Module.
Industrial Ethernet Sensor Node
The PIC18F96J60T-I/PT is purpose-built for industrial Ethernet nodes because the integrated 10 Mbps MAC and on-chip PHY remove the external Ethernet controller. At 41.667 MHz, 64 KB of Flash, and 3808 bytes of RAM, it runs Microchip's TCP/IP Lite stack with room for Modbus/TCP, MQTT-SN, or HTTP web pages. Its 16-channel 10-bit ADC and 70 I/O lines handle multiple analog sensors, optocouplers, and relay drivers directly. The -40C to +85C industrial temperature range suits factory-floor installations. Design tip: place 100 nF and 10 uF decoupling caps within 5 mm of every VDD/VSS pair and route the Ethernet TPO+/TPO- and TPI+/TPI- differential pair per Microchip AN871 to meet IEC 61000 emissions targets.
Empfohlen
Building Automation Controller
The PIC18F96J60T-I/PT fits building automation controllers thanks to its integrated Ethernet MAC+PHY and rich peripheral set. With 64 KB of Flash and 3808 bytes of RAM, it can host BACnet/IP, LonWorks/IP gateways, or simple HTTP control pages. The 70 I/O lines plus two UART modules drive RS-485 subnets for HVAC, lighting, and access-control panels, while 16 ADC inputs read temperature, humidity, and occupancy sensors. Operating from 2.0 V to 3.6 V with -40C to +85C range, it is suitable for rooftop or basement equipment. Best practice: use the integrated Ethernet transformer footprint and follow IEEE 802.3 isolation guidance with a 1.5 kV Ethernet transformer.
Empfohlen
Remote Sensor Gateway
The PIC18F96J60T-I/PT is ideal for remote sensor gateways because it combines Ethernet connectivity, A/D conversion, and control logic on one chip. Its 16 ADC channels and 70 I/O lines interface with temperature, pressure, and flow sensors, while the integrated 10BASE-T Ethernet MAC forwards data to a central SCADA server. The 3808-byte RAM accommodates TCP/IP buffers and modest application memory, and 64 KB of Flash stores the stack plus custom protocol code. The internal oscillator eliminates external crystals, reducing BOM cost. Field firmware upgrades are straightforward through ICSP without removing the device, and the unique device ID supports secure commissioning.
Empfohlen
Smart Meter / Utility Endpoint
The PIC18F96J60T-I/PT is well-suited for smart-meter and utility-endpoint designs because its integrated Ethernet MAC+PHY and 10-bit ADC simplify AMI data aggregation. The 64 KB Flash stores metering firmware plus TCP/IP stack, while 3808 bytes of RAM holds metering tables and connection buffers. The 70 I/O lines connect to metrology ICs, LCDs, and tamper-detection switches, and the wide 2.0-3.6 V supply range simplifies battery-backed designs. Operating over -40C to +85C supports outdoor enclosures. Best practice: use cryptographic libraries from Microchip to protect consumption data, and isolate the Ethernet port with a 1.5 kV transformer for surge protection per IEC 61000-4-5.
Empfohlen
Appliance Networking Module
The PIC18F96J60T-I/PT is a strong fit for appliance networking modules that report status, error codes, or telemetry over Ethernet. With 64 KB program memory, 3808 bytes of RAM, and an integrated 10BASE-T MAC+PHY, the device supports HTTP, MQTT, and vendor-specific IoT protocols without external Ethernet silicon. The internal PLL-driven oscillator runs the part at 41.667 MHz, allowing responsive UI tasks, while 70 I/O lines drive displays, keypads, and motor-control feedback paths. The -40C to +85C range handles the heat of laundry, oven, or outdoor equipment. Place a TVS diode across the Ethernet lines and follow IEC 61000-4-2 ESD placement rules.
Empfohlen
Embedded Web-Server Module
The PIC18F96J60T-I/PT is excellent for embedded web-server modules used to configure or monitor industrial equipment. The integrated 10BASE-T MAC+PHY eliminates external Ethernet ICs and brings BOM cost down to a single MCU plus magnetics. The 64 KB Flash and 3808-byte RAM are enough for a small HTTP server with custom CGI pages, while 16 ADC channels read system status. Operating voltage of 2.0-3.6 V supports 3.3 V rails, and the 70 I/O lines provide ample headroom for buttons, LEDs, and configuration EEPROM. The internal oscillator plus PLL eliminates an external crystal, simplifying the BOM to MCU plus magnetics plus passives.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC18F96J60T-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC18F96J60-I/PT | PIC18F97J60T-I/PT | PIC18F96J60T-I/PF | PIC18F86J60T-I/PT |
|---|---|---|---|---|---|
| Package | 100-TQFP (12x12 mm) | 100-TQFP (12x12 mm) | 100-TQFP (12x12 mm) | 100-TQFP | 100-TQFP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 64 KB | 64 KB | 128 KB | 64 KB | 64 KB |
| RAM | 3808 bytes | 3808 bytes | 3808 bytes | 3808 bytes | 3808 bytes |
| Max Clock | 41.667 MHz | 41.667 MHz | 41.667 MHz | 41.667 MHz | 41.667 MHz |
| Operating Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Ethernet MAC+PHY | Yes (10BASE-T) | Yes (10BASE-T) | Yes (10BASE-T) | Yes (10BASE-T) | Yes (10BASE-T) |
| Pin Count / Package Code | 100 pins (PT) | 100 pins (PT) | 100 pins (PT) | 100 pins (PF) | 100 pins (PT) |
Wichtigste Unterscheidungsmerkmale
- Integrated 10BASE-T Ethernet MAC and PHY in one chip (vs. PIC18F87J60T-I/PT (80-pin))
- 100-pin TQFP with full 70-I/O set (vs. PIC18F87J60T-I/PT (80-pin))
- Drop-in upgrade path to 128 KB Flash (vs. PIC18F96J60-I/PT (same Flash))
Designhinweise
The Ethernet TPO+/TPO- and TPI+/TPI- pins must be routed as 100-ohm differential pairs with matched length and continuous ground reference, per Microchip AN871. Keep the traces short and avoid vias. Place the 1.5 kV Ethernet transformer within 25 mm of the PHY pins and provide a dedicated ground pour under the magnetics to suppress common-mode emissions and meet IEEE 802.3 and IEC 61000-4-2 ESD targets.
Add 100 nF ceramic decoupling capacitors on every VDD pin pair and a single 10 uF bulk cap near the IC. The Ethernet MAC draws short current spikes during frame transmit, so the regulator should provide at least 200 mA dynamic headroom. The internal oscillator PLL is sensitive to VDD noise, so keep digital and analog supply traces separated and use a ferrite bead if required.
Do not confuse the PT (100-pin TQFP) and PF (Pb-free finish) suffixes - both refer to the same 100-pin TQFP package with identical pinouts. The T suffix denotes tape-and-reel packaging format, while the absence of T indicates tray. MCLR must be tied to VDD through a 10 kohm resistor for normal operation, and an ICSP programmer must use high-voltage (13V) entry on MCLR to program the device.
Compliance-Informationen
RoHS compliant per Microchip product page. Not AEC-Q100 qualified; choose PIC18F67J60 family for automotive-grade Ethernet.
