PIC18F97J60-I/PT - 8-bit MCU w/ 10Mbps Ethernet, 128KB Flash
Teilenummer: PIC18F97J60-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $11.83 | $11,83 |
| 10 | $10.78 | $107,80 |
| 100 | $9.65 | $965,00 |
| 500 | $8.94 | $4.470,00 |
| 1.000 | $8.12 | $8.120,00 |
PIC18F97J60-I/PT Übersicht
A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (Flash), data memory (RAM), and a rich set of on-chip peripherals such as timers, ADCs, communication controllers, and I/O ports. The PIC18F97J60 belongs to Microchip's PIC18J family, which uses a 16-bit enhanced Harvard architecture that targets higher-performance, Ethernet-connected embedded designs. Its hierarchy places it within 8-bit microcontrollers -> Microchip PIC family -> PIC18 high-performance sub-family -> PIC18J Ethernet-enabled series.
Key features include the integrated IEEE 802.3 10BASE-T Ethernet controller with on-chip PHY and dedicated DMA, an 8-channel hardware modulator for IrDA/SIR, two MSSP (SPI/I2C) ports, two USART modules, two capture/compare/PWM modules, and 70 I/O pins. The on-chip PHY eliminates external Ethernet magnetics and dramatically reduces BOM cost compared to MCU-plus-external-MAC designs.
The device uses an enhanced RISC pipeline with 32-level hardware stack and vectored interrupts, executed from Flash or external memory. The 100-pin TQFP package provides abundant I/O for parallel buses and memory-mapped LCDs, while a wide operating voltage of 2.0-3.6 V and -40C to +85C industrial temperature range support harsh industrial environments.
Typical applications include industrial automation (Modbus/TCP gateways, remote sensor nodes), building automation (BACnet/IP controllers, access panels), and remote monitoring (web/SCADA interfaces). The integrated Ethernet peripheral makes the part especially attractive for designers replacing RS-485 or CAN-based infrastructure with low-cost TCP/IP connectivity.
When designing with the PIC18F97J60-I/PT, allocate at least 8 KB of Flash for the TCP/IP stack (Microchip's MLA or Harmony-based stack) and carefully observe the Ethernet PCB layout guidelines (4-layer board, controlled-impedance 100-ohm differential traces, dedicated ground pour). The internal 3.3 V LDO must be bypassed with 10 uF and 0.1 uF capacitors placed close to the VDD pins.
Drop-in-Alternativen für PIC18F97J60-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC18F97J60-I/PT (gleiche Bauform und Footprint) – abweichend in Package, Program Memory (Flash), RAM, ADC, Core.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC18F97J60T-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC18F96J60-I/PT
✅ Drop-In✓ Auf Lager
$4.97 / Stück
Datenblatt ansehen →PIC18F87J60-I/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$5.65 / Stück
Datenblatt ansehen →PIC18F96J94-I/PF
✅ Drop-In✓ Auf Lager
$2.17 / Stück
Datenblatt ansehen →PIC18F97J60-I/PT Grenzwerte & elektrische Eigenschaften
| Core Architecture | PIC18, 8-bit enhanced Harvard RISC |
| Instruction Set Width | 16 bits |
| Program Memory (Flash) | 128 KB (64K x 16) |
| RAM | 3808 bytes |
| EEPROM | Not present (uses Flash emulation) |
| Maximum CPU Frequency | 41.667 MHz |
| Instruction Cycle Time | 200 ns |
| Performance | 16 MIPS (million instructions per second) |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| Betriebstemperatur | -40 C to +85 C (Industrial) |
| I/O Pins | 70 |
| Ethernet Peripheral | Integrated IEEE 802.3 10BASE-T MAC + PHY |
| ADC | 10-bit, up to 16 channels |
| Communication Peripherals | 2x USART, 2x MSSP (SPI/I2C), 1x Ethernet, 1x IrDA |
| Timers | 5 x 16-bit / 8-bit Timer modules |
| PWM / CCP | 2 Capture/Compare/PWM modules |
| Gehäuse | 100-pin TQFP (PT), 12x12 mm |
| Montageart | Surface Mount |
| MSL-Level | 3 (168 hours) |
| RoHS-Status | Compliant |
PIC18F97J60-I/PT Pin-Konfiguration
| Pin 1 | RG0/INT0 — PORTG bit 0 / External interrupt 0 |
| Pin 2 | RG1/INT1 — PORTG bit 1 / External interrupt 1 |
| Pin 3 | RG2/INT2 — PORTG bit 2 / External interrupt 2 |
| Pin 4 | RG3/INT3 — PORTG bit 3 / External interrupt 3 |
| Pin 5 | MCLR — Master Clear (reset) input, active low |
| Pin 6 | RG4 — PORTG bit 4 |
| Pin 7 | RG5 — PORTG bit 5 |
| Pin 8 | VDD — Digital supply voltage (3.3 V) |
| Pin 9 | VSS — Digital ground |
| Pin 10 | RF7 — PORTF bit 7 |
| Pin 11 | RF6 — PORTF bit 6 |
| Pin 12 | RB7 — PORTB bit 7 |
| Pin 13 | RB6 — PORTB bit 6 |
| Pin 14 | RB5 — PORTB bit 5 |
| Pin 15 | RB4 — PORTB bit 4 |
| Pin 16 | RB3 — PORTB bit 3 |
| Pin 17 | RB2 — PORTB bit 2 |
| Pin 18 | RB1 — PORTB bit 1 |
| Pin 19 | RB0 — PORTB bit 0 |
| Pin 20 | VDD — Digital supply voltage (3.3 V) |
| Pin 21 | VSS — Digital ground |
| Pin 22 | RD7 — PORTD bit 7 |
| Pin 23 | RD6 — PORTD bit 6 |
| Pin 24 | RD5 — PORTD bit 5 |
| Pin 25 | RD4 — PORTD bit 4 |
| Pin 26 | RD3 — PORTD bit 3 |
| Pin 27 | RD2 — PORTD bit 2 |
| Pin 28 | RD1 — PORTD bit 1 |
| Pin 29 | RD0 — PORTD bit 0 |
| Pin 30 | RC7 — PORTC bit 7 |
| Pin 31 | RC6 — PORTC bit 6 |
| Pin 32 | RC5 — PORTC bit 5 |
| Pin 33 | RC4 — PORTC bit 4 |
| Pin 34 | RC3 — PORTC bit 3 |
| Pin 35 | RC2 — PORTC bit 2 |
| Pin 36 | RC1 — PORTC bit 1 |
| Pin 37 | RC0 — PORTC bit 0 |
| Pin 38 | RE7 — PORTE bit 7 |
| Pin 39 | RE6 — PORTE bit 6 |
| Pin 40 | RE5 — PORTE bit 5 |
| Pin 41 | RE4 — PORTE bit 4 |
| Pin 42 | RE3 — PORTE bit 3 |
| Pin 43 | RE2 — PORTE bit 2 |
| Pin 44 | RE1 — PORTE bit 1 |
| Pin 45 | RE0 — PORTE bit 0 |
| Pin 46 | RA7 — PORTA bit 7 |
| Pin 47 | RA6 — PORTA bit 6 |
| Pin 48 | RA5 — PORTA bit 5 |
| Pin 49 | RA4 — PORTA bit 4 |
| Pin 50 | RA3 — PORTA bit 3 |
| Pin 51 | RA2 — PORTA bit 2 |
| Pin 52 | RA1 — PORTA bit 1 |
| Pin 53 | RA0 — PORTA bit 0 |
| Pin 54 | VSS — Digital ground |
| Pin 55 | VDD — Digital supply voltage (3.3 V) |
| Pin 56 | VSS — Digital ground |
| Pin 57 | VDD — Digital supply voltage (3.3 V) |
| Pin 58 | RF0 — PORTF bit 0 |
| Pin 59 | RF1 — PORTF bit 1 |
| Pin 60 | RF2 — PORTF bit 2 |
| Pin 61 | RF3 — PORTF bit 3 |
| Pin 62 | RF4 — PORTF bit 4 |
| Pin 63 | RF5 — PORTF bit 5 |
| Pin 64 | RH7 — PORTH bit 7 |
| Pin 65 | RH6 — PORTH bit 6 |
| Pin 66 | RH5 — PORTH bit 5 |
| Pin 67 | RH4 — PORTH bit 4 |
| Pin 68 | RH3 — PORTH bit 3 |
| Pin 69 | RH2 — PORTH bit 2 |
| Pin 70 | RH1 — PORTH bit 1 |
| Pin 71 | RH0 — PORTH bit 0 |
| Pin 72 | RJ7 — PORTJ bit 7 |
| Pin 73 | RJ6 — PORTJ bit 6 |
| Pin 74 | RJ5 — PORTJ bit 5 |
| Pin 75 | RJ4 — PORTJ bit 4 |
| Pin 76 | RJ3 — PORTJ bit 3 |
| Pin 77 | RJ2 — PORTJ bit 2 |
| Pin 78 | RJ1 — PORTJ bit 1 |
| Pin 79 | RJ0 — PORTJ bit 0 |
| Pin 80 | VSS — Digital ground |
| Pin 81 | VDD — Digital supply voltage (3.3 V) |
| Pin 82 | TPOUT+ — Ethernet differential transmit output (positive) |
| Pin 83 | TPOUT- — Ethernet differential transmit output (negative) |
| Pin 84 | RBIAS — Ethernet PHY bias resistor connection |
| Pin 85 | VDDRUN — Internal regulator output for Ethernet PHY (3.3 V) |
| Pin 86 | TPIN+ — Ethernet differential receive input (positive) |
| Pin 87 | TPIN- — Ethernet differential receive input (negative) |
| Pin 88 | VSSPLL — PLL ground |
| Pin 89 | VDDPLL — PLL supply voltage |
| Pin 90 | OSC1 — Crystal oscillator input |
| Pin 91 | OSC2 — Crystal oscillator output |
| Pin 92 | VDD — Digital supply voltage (3.3 V) |
| Pin 93 | VSS — Digital ground |
| Pin 94 | RK7 — PORTK bit 7 |
| Pin 95 | RK6 — PORTK bit 6 |
| Pin 96 | RK5 — PORTK bit 5 |
| Pin 97 | RK4 — PORTK bit 4 |
| Pin 98 | RK3 — PORTK bit 3 |
| Pin 99 | RK2 — PORTK bit 2 |
| Pin 100 | RK1 — PORTK bit 1 |
Typische Anwendungen
PIC18F97J60-I/PT ist geeignet für 6 Anwendungs: Industrial Ethernet Sensor Node, Building Automation Controller, Web/SCADA Remote Monitor, IoT Ethernet Gateway, Point-of-Sale / Vending Ethernet Bridge, Security / Access Control Panel.
Industrial Ethernet Sensor Node
The PIC18F97J60-I/PT's integrated 10BASE-T MAC/PHY and 128 KB Flash make it ideal for distributed industrial sensor nodes that publish Modbus/TCP or simple HTTP/JSON telemetry. Its 16 MIPS throughput handles both the TCP/IP stack (Microchip MLA, ~8 KB Flash) and the application code (sensor sampling, calibration) within a single chip. The 2.0-3.6 V supply and -40 C to +85 C industrial temperature range cover harsh factory environments, while 70 I/O pins accommodate multiple sensor inputs and digital outputs. Compared to MCU+external-PHY designs, the on-chip PHY removes a major BOM line and simplifies PCB layout.
Empfohlen
Building Automation Controller
Building automation BACnet/IP and Modbus TCP controllers benefit from the PIC18F97J60-I/PT's integrated Ethernet and 128 KB of program Flash. The on-chip 10-bit ADC scans temperature, humidity, and occupancy sensors while two USART modules interface with legacy RS-485 HVAC equipment. The 70 I/O pins drive relay outputs, triac controls, and indicator LEDs directly without external logic. Per the Microchip datasheet, the industrial temperature range of -40 C to +85 C supports rooftop and mechanical-room installations. The integrated HP Auto-MDIX eliminates crossover cable headaches during commissioning.
Empfohlen
Web/SCADA Remote Monitor
The PIC18F97J60-I/PT powers compact web-enableable SCADA remote terminal units (RTUs) by running an embedded HTTP server with HTML/JSON status pages and a simple TCP socket listener for SCADA polling. The 128 KB Flash fits both the TCP/IP stack and the application web pages. With 3,808 B RAM and a 200 ns instruction cycle, the part can sustain ~10 simultaneous connections on a 10 Mbps network. The integrated PHY eliminates external magnetics complexity - designers only need the 1:1 transformer and RJ-45 jack.
Empfohlen
IoT Ethernet Gateway
The PIC18F97J60-I/PT serves as a cost-optimized Ethernet-to-serial/IoT gateway that bridges Wi-Fi-less endpoints to the LAN. Its two USART modules connect to Bluetooth or ZigBee co-processors, while MSSP ports host SPI sensors. The integrated Ethernet peripheral publishes aggregated sensor data over HTTP/MQTT. With 128 KB Flash, the part handles a complete TLS-lite or unsecured MQTT client alongside routing logic. The 3.3 V single-supply operation simplifies power tree design for compact IoT gateway enclosures.
Empfohlen
Point-of-Sale / Vending Ethernet Bridge
Vending and POS equipment often requires retrofit Ethernet for inventory telemetry without redesigning the host controller. The PIC18F97J60-I/PT acts as a co-processor that translates legacy RS-232/RS-485 POS traffic onto Ethernet (EtherNet/IP, TCP socket). Its 128 KB Flash stores a vendor-specific protocol stack, while the integrated 10 Mbps Ethernet handles backhaul traffic. The industrial temperature grade and 2.0-3.6 V supply fit unattended kiosk environments with wide temperature swings and battery-backed 3.3 V rails.
Empfohlen
Security / Access Control Panel
Access control panels using the PIC18F97J60-I/PT leverage its 70 I/O pins for Wiegand readers, door strikes, REX sensors, and status LEDs while publishing events to a centralized access control server over Ethernet. The integrated 10BASE-T PHY supports PoE-style deployments with the addition of a passive splitter, and 128 KB Flash fits TLS handshake and credential caching logic. The -40 C to +85 C operating range covers outdoor gate controllers, while the integrated PHY enables real-time door status updates with sub-second latency over the LAN.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC18F97J60-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC18F97J60T-I/PT | PIC18F96J60-I/PT | PIC18F87J60-I/PT | PIC18F96J94-I/PF |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-pin TQFP (PT) | 100-pin TQFP (PT) | 100-pin TQFP (PT) | 80-pin TQFP (PT) | 100-pin TQFP (PF) |
| Flash Memory | 128 KB | 128 KB | 64 KB | 128 KB | 64 KB |
| Max CPU Frequency | 41.667 MHz (16 MIPS) | 41.667 MHz (16 MIPS) | 41.667 MHz (16 MIPS) | 41.667 MHz (16 MIPS) | 41.667 MHz (16 MIPS) |
| Integrated Ethernet PHY | Yes (10BASE-T, MAC + PHY) | Yes (10BASE-T, MAC + PHY) | Yes (10BASE-T, MAC + PHY) | Yes (10BASE-T, MAC + PHY) | No (MAC only, external PHY required) |
| Supply Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Approx. Unit Price (qty 1, USD) | $11.83 | ~$11.83 | ~$10.50 | ~$11.50 | ~$13.20 |
Wichtigste Unterscheidungsmerkmale
- Integrated 10BASE-T MAC + PHY on a single 8-bit MCU die (vs. PIC18F97J94-I/PF)
- Double the Flash memory versus PIC18F96J60 sibling (vs. PIC18F96J60-I/PT)
- Highest I/O count in the PIC18F97J60 family (vs. PIC18F87J60-I/PT)
- Industrial temperature grade -40 C to +85 C in 100-pin TQFP (vs. PIC18F96J60-I/PF (100-pin TQFP, PF suffix))
Designhinweise
The integrated 10BASE-T Ethernet PHY is highly sensitive to PCB layout. Use a 4-layer board with a continuous ground plane beneath the Ethernet signal traces. The TPOUT+/TPOUT- and TPIN+/TPIN- pairs must be routed as 100-ohm differential pairs with matched lengths within 2 mm. Keep the RBIAS resistor within 5 mm of pin 84 and the VDDRUN/VDDPLL decoupling caps within 3 mm of their respective pins. Reference Microchip AN1120 for the recommended magnetics and RJ-45 jack selection.
The PIC18F97J60-I/PT has multiple VDD/VSS pins that must all be connected and bypassed. Place a 0.1 uF ceramic capacitor close to each VDD/VSS pair, and add a bulk 10 uF tantalum or ceramic capacitor near the package. The internal 3.3 V regulator requires a 4.7 uF low-ESR capacitor on VDDRUN (pin 85) and VDDPLL (pin 89) for stable operation. Without proper bypassing, the Ethernet PHY will exhibit high bit-error rates or link failure.
Crystal placement is critical for the Ethernet MAC. The 25 MHz or 41.667 MHz crystal (per oscillator configuration) should be placed within 10 mm of pins 90/91 with short, symmetric traces and a guard ground ring. Avoid routing any switching signals (PWM, digital outputs) near the crystal traces or the Ethernet differential pairs. The MCLR pin should have a 10 kohm pull-up to VDD and a 100 nF cap to ground for in-circuit serial programming (ICSP) reliability.
Do not assume the 128 KB Flash is fully available for application code - the TCP/IP stack (MLA or Harmony-based) consumes 8-15 KB. Reserve at least one Flash erase page (1024 bytes) for EEPROM emulation and at least 4 KB for bootloader/field-update capability. The Ethernet MAC requires a unique 48-bit MAC address; design in a MAC address EEPROM like 25AA02E48 to avoid hard-coding addresses per unit.
Although the Ethernet PHY is integrated, the TPOUT+/- signals still pass through external 1:1 isolation transformers before the RJ-45 connector. Choose a transformer with integrated common-mode chokes (e.g., Pulse H1102 or equivalent) to meet IEEE 802.3 emissions requirements. The center tap of the transmit transformer should connect to VDDRUN, and the receive center tap should connect to a quiet 3.3 V supply via a ferrite bead - this improves EMI performance significantly.
Compliance-Informationen
RoHS and REACH compliant per Microchip product declaration. Lead-free TQFP (PT) termination. Industrial temperature grade -40 C to +85 C. AEC-Q100 not applicable - this is a microcontroller, not an automotive-grade IC; designers needing AEC-Q100 should consider PIC18F67J60-I/PT automotive variants or PIC32MX equivalents.
