PIC18LF25J10-I/SO - 32KB Flash 8-bit MCU 28-SOIC | Microchip
Teilenummer: PIC18LF25J10-I/SO ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $3.85 | $3,85 |
| 10 | $3.42 | $34,20 |
| 100 | $2.95 | $295,00 |
| 500 | $2.62 | $1.310,00 |
| 1.000 | $2.31 | $2.310,00 |
PIC18LF25J10-I/SO Übersicht
What is a PIC18J microcontroller? An 8-bit microcontroller is a single-chip computer integrating a CPU core, program memory, data memory, and peripherals such as timers, communication ports, and analog-to-digital converters on one die. The PIC18 family is Microchip's high-end 8-bit line built around an enhanced RISC architecture with hardware multiplier, hardware accumulator, and a 16-bit instruction word. The 'J' sub-family extends this lineage with nanoWatt XLP deep-sleep modes, ultra-low-power sleep currents, and on-chip peripherals aimed at battery-powered and energy-harvesting designs.
Key features of the PIC18LF25J10 include ten 10-bit A/D converter channels with automatic acquisition, multiple Enhanced Capture/Compare/PWM modules, two UART modules with IrDA support, an I2C/SPI master/slave port, and a full-speed USB 2.0 device/host/OTG controller. The 32KB Flash provides ample headroom for USB stacks and application firmware, while the integrated 1KB SRAM and 256-byte data EEPROM support real-time data logging. NanoWatt XLP technology delivers sub-microamp sleep currents critical for battery longevity.
Architecturally the PIC18LF25J10 is a Harvard-design CMOS device with separate program and data buses, a 16-bit flash-fetch that decodes into an 8-bit ALU datapath, and a priority-based interrupt controller. The integrated USB SIE eliminates external transceivers for low-speed and full-speed USB peripherals, simplifying BOM and PCB routing versus discrete implementations.
Typical applications include low-power USB peripherals (HID mice, keyboards, custom HID devices), portable data loggers with USB charging, industrial sensor interfaces, low-cost instrumentation, and consumer devices needing XLP-class sleep currents. Engineers frequently pair it with external EEPROM for parameter storage and a low-cost voltage regulator.
When designing with this MCU, ensure that the core 3.3V rail is well decoupled with both a 100 nF ceramic near each VDD pin and a bulk tantalum or aluminum-polymer capacitor. Do not confuse the LF (low-voltage, 2.0-3.6V) variant with the PIC18F25J10 (4.2-5.5V) variant - they are NOT pin-compatible at the power pin level. Confirm VDD range matches your rail before PCB layout is committed.
This page synthesizes XAIPART distributor pricing, drop-in replacement alternatives drawn from the PIC18LF family and cross-brand 8-bit MCUs, plus practical design notes that go beyond the bare Microchip datasheet. For engineers evaluating longevity or evaluating drop-in upgrades, this aggregate view supports quicker sourcing decisions.
Drop-in-Alternativen für PIC18LF25J10-I/SO – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC18LF25J10-I/SO (gleiche Bauform und Footprint) – abweichend in ADC, Operating Temperature, MSL Level, Package, Core Architecture.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC18LF25J10T-I/SO
✅ Drop-In✓ Auf Lager
$2.3 / Stück
Datenblatt ansehen →PIC18LF24J10-I/SO
✅ Drop-In✓ Auf Lager
$1.91 / Stück
Datenblatt ansehen →PIC18LF24J11-I/SO
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PIC18LF25J50-I/SO
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$2.75 / Stück
Datenblatt ansehen →PIC18LF2455-I/SO
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$2.05 / Stück
Datenblatt ansehen →PIC18LF25J10-I/SO Grenzwerte & elektrische Eigenschaften
| Product Type | 8-bit RISC Microcontroller |
| Core | PIC18 (Enhanced Harvard, 16-bit instruction word) |
| Series | PIC 18J |
| Program Memory | 32 KB Flash (16K x 16) |
| Data Memory (SRAM) | 1 KB (1024 bytes) |
| Data EEPROM | Not present on this variant |
| Maximale Taktfrequenz | 40 MHz |
| Instruction Throughput | 10 MIPS at 40 MHz |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| Betriebstemperatur | -40 C to +85 C (Industrial) |
| Gehäuse | 28-pin SOIC (SO), 7.50 mm body width |
| Montageart | Surface Mount |
| ADC | 10-bit, up to 10 channels (SAR) |
| USB | USB 2.0 Full-/Low-Speed SIE on-chip |
| Communication Interfaces | 2x UART (IrDA), 1x I2C/SPI (MSSP), 1x USB SIE |
| Timers | 2x 8-bit, 3x 16-bit Timer/Counter |
| PWM Channels | Up to 5 ECCP/ECCP + CCP outputs |
| RoHS-Status | Compliant |
| Lead-Free | Yes |
| MSL-Level | 1 (unlimited floor life) |
PIC18LF25J10-I/SO Pin-Konfiguration
| Pin 1 | RA2/AN2 — GPIO RA2 / analog input AN2 |
| Pin 2 | RA3/AN3/VREF+ — GPIO RA3 / analog input AN3 / ADC positive reference |
| Pin 3 | RA4/AN4 — GPIO RA4 / analog input AN4 |
| Pin 4 | RA5/AN5 — GPIO RA5 / analog input AN5 |
| Pin 5 | VSS — Ground reference |
| Pin 6 | RA7 — GPIO RA7 |
| Pin 7 | RA6/OSC2 — GPIO RA6 / oscillator output |
| Pin 8 | VDD — Positive supply voltage (2.0 V to 3.6 V) |
| Pin 9 | RB0/INT0/FLT0 — GPIO RB0 / external interrupt 0 / PWM fault input |
| Pin 10 | RB1/INT1 — GPIO RB1 / external interrupt 1 |
| Pin 11 | RB2/INT2 — GPIO RB2 / external interrupt 2 |
| Pin 12 | RB3/INT3 — GPIO RB3 / external interrupt 3 |
| Pin 13 | RB4/KBI0 — GPIO RB4 / keyboard interrupt 0 |
| Pin 14 | RB5/KBI1 — GPIO RB5 / keyboard interrupt 1 |
| Pin 15 | RB6/KBI2/PGC — GPIO RB6 / keyboard interrupt 2 / ICSP clock |
| Pin 16 | RB7/KBI3/PGD — GPIO RB7 / keyboard interrupt 3 / ICSP data |
| Pin 17 | VUSB — USB transceiver internal supply (bypass with 220 nF) |
| Pin 18 | RC4/D-/VMO — USB D- / GPIO RC4 |
| Pin 19 | RC5/D+/VPO — USB D+ / GPIO RC5 |
| Pin 20 | RC6/TX1/CK1 — GPIO RC6 / UART1 TX / UART1 clock |
| Pin 21 | RC7/RX1/DT1 — GPIO RC7 / UART1 RX / UART1 data |
| Pin 22 | RD0 — GPIO RD0 |
| Pin 23 | RD1 — GPIO RD1 |
| Pin 24 | RD2 — GPIO RD2 |
| Pin 25 | RD3 — GPIO RD3 |
| Pin 26 | RC0/SOSCO — GPIO RC0 / secondary oscillator output |
| Pin 27 | RC1/SOSCI — GPIO RC1 / secondary oscillator input |
| Pin 28 | RC2/CCP1 — GPIO RC2 / CCP1 PWM output |
Typische Anwendungen
PIC18LF25J10-I/SO ist geeignet für 6 Anwendungs: USB HID Peripheral Device, Battery-Powered Sensor Logger, Industrial Sensor Interface Module, Consumer Remote Control with USB Charging, Educational Microcontroller Trainer Board, Low-Cost Medical Accessory.
USB HID Peripheral Device
The PIC18LF25J10-I/SO is purpose-built for low-cost USB Human Interface Devices thanks to its on-chip USB 2.0 Full-/Low-Speed SIE and 32 KB of program space. According to the PIC18F25J10 datasheet DS39791D, the integrated SIE handles NRZI encoding, bit stuffing, and packet framing in hardware, eliminating the external transceiver needed by earlier PIC16 designs. With 1 KB of SRAM it comfortably supports HID boot-loader plus application code, while 2.0-3.6 V operation lets it draw directly from the USB 3.3 V rail. Compared with discrete USB implementations it cuts BOM by roughly 30-40% and reduces PCB area, but engineers should still add a 27 pF D+ pull-up and ferrite bead on VUSB for EMI compliance.
Empfohlen
Battery-Powered Sensor Logger
The PIC18LF25J10-I/SO nanoWatt XLP technology delivers deep-sleep currents below 1 uA, making it well suited to battery-powered sensor loggers that wake intermittently to capture temperature, pressure, or motion data. Its 10-bit ADC with up to 10 channels multiplexes analog sensors without an external MUX, while the 32 KB Flash stores weeks of timestamped readings with simple ring-buffer logic. Operating down to 2.0 V lets a single 2xAA alkaline or single CR2032 lithium cell run the design without boost conversion, though a low-dropout regulator improves immunity to battery droop. Trade-off versus a 32-bit ARM Cortex-M0 alternative: lower MIPS ceiling and no DMA, but a 50-70% lower sleep current and 8-bit code density that doubles effective Flash utilization.
Empfohlen
Industrial Sensor Interface Module
In industrial 4-20 mA loop-powered or 24 V-bus sensor interfaces, the PIC18LF25J10-I/SO delivers reliable UART and SPI connectivity for transducer conditioning, with the LF 2.0-3.6 V range matching a small on-board switching regulator. Its 28-SOIC package survives industrial operating temperatures from -40 C to +85 C as confirmed by the 'I' temperature suffix, and its 10-bit ADC over 10 inputs allows multi-channel transducer sampling. Compared with a 16-bit PIC24 alternative the 8-bit part trades converter resolution for 40-50% cost savings and far simpler firmware. Engineers must add TVS protection on the UART pins and a digital isolator for any 4-20 mA loop crossing hazardous-area boundaries per IEC 60079 if the module sits in a Zone 1 environment.
Empfohlen
Consumer Remote Control with USB Charging
The PIC18LF25J10-I/SO powers consumer USB-charged remote controls and presentation clickers that need occasional wired connectivity for firmware updates. Its 40 MHz clock drives IR modulation at standard 36/40 kHz carrier frequencies for consumer-electronics protocols, and the 1 KB SRAM supports queueing multiple button events without drops. The integrated USB SIE enables DFU bootloader over USB for end-user firmware refresh, eliminating the need for JTAG pods at consumer cost points. Compared with a 16-bit PIC24 design this 8-bit PIC delivers a 50%+ BOM cost advantage and a 30% smaller PCB, but the engineer trades off mathematical precision for bit-level GPIO control.
Empfohlen
Educational Microcontroller Trainer Board
Educational and hobbyist trainer boards frequently select the PIC18LF25J10-I/SO because it exposes USB, UART, SPI, I2C, ADC, PWM, and timers in a single 28-SOIC without external peripherals. The 32 KB Flash holds textbook examples, USB HID stacks, and bootloader code with room to spare, while the LF 3.3 V operation eliminates level-shifter complexity when connecting to modern 3.3 V sensors and SD cards. Its PICkit 3 or PICkit 4 ICSP programming header and Microchip's free MPLAB X IDE make it one of the lowest-cost paths to learning USB device firmware. Trade-off versus a 32-bit ARM Cortex-M0 trainer: 4x lower MIPS ceiling, but 50% lower unit cost and 70% lower sleep current.
Empfohlen
Low-Cost Medical Accessory
Low-cost medical accessories like pill dispensers, pulse-oximeter dongles, and glucose-meter add-ons leverage the PIC18LF25J10-I/SO for its nanoWatt XLP sleep currents and integrated USB SIE. The 10-bit ADC captures pulse-oximeter photodiode outputs, the I2C MSSP drives a small OLED display, and the UART interfaces with a Bluetooth module for telemetry to a phone. Compared with a 32-bit ARM Cortex-M4F design it sacrifices DSP performance for 60-70% BOM savings - acceptable for accessories where the heavy compute is in the host phone. Engineers must add a low-leakage LDO and ESD protection on any skin-contact electrode per IEC 60601 if the accessory is patient-coupled.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC18LF25J10-I/SO – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC18LF25J10T-I/SO | PIC18LF24J10-I/SO | PIC18LF24J11-I/SO | PIC18LF25J50-I/SO | PIC18LF2455-I/SO |
|---|---|---|---|---|---|---|
| Package | 28-SOIC (SO) | 28-SOIC (SO) - same | 28-SOIC (SO) - same | 28-SOIC (SO) - same | 28-SOIC (SO) - same | 28-SOIC (SO) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 32 KB | 32 KB | 16 KB | 16 KB | 32 KB | 24 KB |
| Data Memory (SRAM) | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 2 KB |
| Operating Voltage (VDD) | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Maximum Clock Frequency | 40 MHz | 40 MHz | 40 MHz | 48 MHz | 48 MHz | 48 MHz |
| USB SIE | Yes (Full-/Low-Speed) | Yes (Full-/Low-Speed) | Yes (Full-/Low-Speed) | Yes (Full-/Low-Speed) | Yes (Full-/Low-Speed) | Yes (Full-Speed) |
| ADC Resolution / Channels | 10-bit / 10 ch | 10-bit / 10 ch | 10-bit / 10 ch | 10-bit / 10 ch | 10-bit / 13 ch | 10-bit / 8 ch |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Wichtigste Unterscheidungsmerkmale
- On-chip USB 2.0 Full-/Low-Speed SIE (vs. PIC18LF24J10-I/SO)
- 32 KB Flash for USB stacks (vs. PIC18LF24J10-I/SO)
- Industrial -40 C to +85 C temperature grade (vs. PIC18LF25J50-I/SO (commercial grade))
Designhinweise
Estimated: At VIN=3.6 V, 40 MHz active mode, the PIC18LF25J10-I/SO draws approximately 14 mA. In deep sleep the nanoWatt XLP sleep current is sub-microamp. Decouple VDD with a 100 nF ceramic placed within 3 mm of the pin, plus a bulk 10 uF tantalum on the rail. Add a ferrite bead on VUSB (pin 17) with 220 nF bypass to ground for USB inrush compliance.
Route the 48 MHz INTOSC output (RA6) away from analog traces; keep the VREF1 (yellow pad beneath the chip on the SOIC) separated by at least 2 mm from digital switching. Place a guard trace around the AVSS pin. Keep USB D+/D- traces length-matched within 2 mm and 90-ohm differential impedance if USB is used. Mount the ICSP PGC/PGD pins (RB6/RB7) for programming access.
Do not assume the PIC18LF25J10-I/SO is 5V tolerant on digital I/O - VOH at 3.6 VDD is approximately 3.0 V into 4.0 mA. Do not connect directly to 5 V logic without a level translator. Verify ICSP programming with PICkit 3 or PICkit 4 uses the correct target VDD (3.3 V). The LF silicon variant will not start on 5 V VDD; use PIC18F25J10 for 5 V systems.
Compliance-Informationen
RoHS compliant per Microchip product page; lead-free SOIC package. AEC-Q100 not qualified (industrial -40 C to +85 C; for automotive select AEC-Q100 qualified variants like PIC18F46J50-I/PT automotive grade).
