PIC24FJ64GB004T-I/PT - 64KB Flash 16-bit USB MCU 44-TQFP | Microchip
Teilenummer: PIC24FJ64GB004T-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $3.5 | $3,50 |
| 10 | $3.18 | $31,80 |
| 100 | $2.75 | $275,00 |
| 500 | $2.45 | $1.225,00 |
| 1.000 | $2.2 | $2.200,00 |
| 3.000 | $1.95 | $5.850,00 |
PIC24FJ64GB004T-I/PT Übersicht
A PIC24F microcontroller is a 16-bit modified-Harvard CPU from Microchip's PIC24 family, bridging the 8-bit PIC16/PIC18 architectures and the 32-bit PIC32 family. PIC24F devices target low-power, USB-equipped, and human-interface applications, integrating peripherals such as USB OTG, comparators, RTCC, and capture/compare/PWM modules on a single die. Within the broader Microcontroller -> 16-bit MCU -> PIC24F -> nanoWatt XLP taxonomy, the PIC24FJ64GB004 sits in the 64-pin-or-fewer, full-speed USB tier.
Key features include a C-compiler-optimized instruction set with a 17-bit x 17-bit single-cycle hardware multiplier and 16-bit hardware divider, 16 working registers, an 8 MHz internal oscillator with 4x PLL option, 33 digital I/O pins, 7 timers, 5 PWM channels, 3 analog comparators, an RTCC, and 13 ADC channels with 10-bit resolution. The integrated USB 2.0 full-speed OTG controller adds a PHY and internal pull-up, eliminating the external transceiver.
Typical applications include USB peripherals (HID, CDC, mass-storage), consumer audio accessories, embedded human-interface devices, low-power data loggers, and educational/development boards. The wide 2.0V to 3.6V VDD range permits direct Li-ion battery operation, and the on-chip RTCC supports calendar functions for metering products.
When designing with this MCU, allocate 4 mA of source/sink headroom per pin and provide a 0.1 uF decoupling cap adjacent to every VDD/VSS pair. The USB D+/D- traces should be 90 ohm differential and routed length-matched for full-speed compliance. Always set the CONFIG words for the right oscillator mode before code execution.
Drop-in-Alternativen für PIC24FJ64GB004T-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC24FJ64GB004T-I/PT (gleiche Bauform und Footprint) – abweichend in Package, ADC, Program Memory (Flash), Core Architecture, Timers.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC24FJ64GB004-I/PT
✅ Drop-In✓ Auf Lager
$3.3 / Stück
Datenblatt ansehen →PIC24FJ32GB004T-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24FJ64GA004T-I/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$4.5 / Stück
Datenblatt ansehen →PIC24FJ64GB004T-I/ML
✅ Drop-In✓ Auf Lager
$3.32 / Stück
Datenblatt ansehen →PIC24FJ48GA004T-I/ML
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$4.1 / Stück
Datenblatt ansehen →PIC24FJ32GB004-I/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$3.72 / Stück
Datenblatt ansehen →PIC24FJ64GB004T-E/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24FJ64GB004-I/PTREL
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24FJ64GB004T-I/PT Grenzwerte & elektrische Eigenschaften
| Core Architecture | PIC24F (16-bit modified Harvard) |
| CPU Speed | 32 MHz (16 MIPS) |
| Program Flash Memory | 64 KB (22K x 24) |
| RAM | 8 KB |
| Operating Voltage | 2.0 V to 3.6 V |
| USB Interface | USB 2.0 Full-Speed OTG with on-chip transceiver |
| I/O Pins | 33 |
| Timers | 7 |
| PWM Channels | 5 |
| Analog Comparators | 3 |
| ADC | 10-bit, 13 channels |
| RTCC | Yes (Real-Time Clock/Calendar) |
| Internal Oscillator | 8 MHz with 4x PLL and multiple divide options |
| Hardware Multiplier | 17-bit x 17-bit single-cycle |
| Hardware Divider | 16-bit |
| nanoWatt XLP Technology | Yes (deep sleep < 1 uA) |
| Betriebstemperatur | -40C to +85C (Industrial) |
| Gehäuse | 44-pin TQFP (10x10x1 mm) |
| Montageart | Surface Mount (Tape & Reel) |
| MSL-Level | 3 |
| RoHS-Status | Compliant |
PIC24FJ64GB004T-I/PT Pin-Konfiguration
| Pin 1 | RP15/RB15 — Remappable I/O / general purpose IO pin 15 of PORTB |
| Pin 2 | RP14/RB14 — Remappable I/O / general purpose IO pin 14 of PORTB |
| Pin 3 | RP13/RB13 — Remappable I/O / general purpose IO pin 13 of PORTB |
| Pin 4 | RP12/RB12 — Remappable I/O / general purpose IO pin 12 of PORTB |
| Pin 5 | RP11/RB11 — Remappable I/O / general purpose IO pin 11 of PORTB |
| Pin 6 | VSS — Ground reference |
| Pin 7 | RP10/RB10 — Remappable I/O / general purpose IO pin 10 of PORTB |
| Pin 8 | RP9/RB9 — Remappable I/O / general purpose IO pin 9 of PORTB |
| Pin 9 | RP8/RB8 — Remappable I/O / general purpose IO pin 8 of PORTB |
| Pin 10 | RP7/RB7 — Remappable I/O / general purpose IO pin 7 of PORTB |
| Pin 11 | RP6/RB6 — Remappable I/O / general purpose IO pin 6 of PORTB |
| Pin 12 | RP5/RB5 — Remappable I/O / general purpose IO pin 5 of PORTB |
| Pin 13 | RP4/RB4 — Remappable I/O / general purpose IO pin 4 of PORTB |
| Pin 14 | RP3/RB3 — Remappable I/O / general purpose IO pin 3 of PORTB |
| Pin 15 | RP2/RB2 — Remappable I/O / general purpose IO pin 2 of PORTB |
| Pin 16 | RP1/RB1 — Remappable I/O / general purpose IO pin 1 of PORTB |
| Pin 17 | RP0/RB0 — Remappable I/O / general purpose IO pin 0 of PORTB |
| Pin 18 | VDD — Positive supply voltage (2.0 V to 3.6 V) |
| Pin 19 | VSS — Ground reference |
| Pin 20 | RA15/RP29 — Remappable I/O of PORTA pin 15 |
| Pin 21 | RA14/RP28 — Remappable I/O of PORTA pin 14 |
| Pin 22 | RA13/RP27 — Remappable I/O of PORTA pin 13 |
| Pin 23 | RA12/RP26 — Remappable I/O of PORTA pin 12 |
| Pin 24 | RA11/RP25 — Remappable I/O of PORTA pin 11 |
| Pin 25 | RA10/RP24 — Remappable I/O of PORTA pin 10 |
| Pin 26 | RA9/RP23 — Remappable I/O of PORTA pin 9 |
| Pin 27 | RA8/RP22 — Remappable I/O of PORTA pin 8 |
| Pin 28 | RA7/RP21 — Remappable I/O of PORTA pin 7 |
| Pin 29 | RA6/RP20 — Remappable I/O of PORTA pin 6 |
| Pin 30 | RA5/RP19 — Remappable I/O of PORTA pin 5 |
| Pin 31 | RA4/RP18 — Remappable I/O of PORTA pin 4 |
| Pin 32 | RA3/RP17 — Remappable I/O of PORTA pin 3 |
| Pin 33 | RA2/RP16 — Remappable I/O of PORTA pin 2 |
| Pin 34 | RA1/RP15 — Remappable I/O of PORTA pin 1 |
| Pin 35 | RA0/RP14 — Remappable I/O of PORTA pin 0 |
| Pin 36 | VUSB — USB 3.3 V regulator output / USB transceiver supply |
| Pin 37 | D+ — USB D+ differential data line |
| Pin 38 | D- — USB D- differential data line |
| Pin 39 | VBUS — USB bus voltage sense input |
| Pin 40 | VDD — Positive supply voltage (2.0 V to 3.6 V) |
| Pin 41 | OSC1/CLKI/RA7 — Crystal oscillator input or external clock input |
| Pin 42 | OSC2/CLKO/RA6 — Crystal oscillator output or clock output |
| Pin 43 | MCLR — Master Clear reset input (active low) |
| Pin 44 | PGED2/RP20 — Programming/debug data line 2 / remappable IO |
Typische Anwendungen
PIC24FJ64GB004T-I/PT ist geeignet für 7 Anwendungs: USB HID Peripherals, USB CDC Virtual COM Port, USB Mass Storage Devices, Industrial Sensor Interface Module, Battery-Powered Data Logger, Consumer Audio Accessory, Educational / Development Board Platform.
USB HID Peripherals
The PIC24FJ64GB004T-I/PT's on-chip USB 2.0 Full-Speed OTG transceiver with internal pull-up and dedicated DMA channels makes it ideal for USB HID peripherals such as keyboards, mice, game controllers, and custom input devices. With 64 KB of Flash the part hosts the full Microchip USB HID stack plus composite descriptor logic, while 8 KB RAM accommodates HID report buffers without external memory. Designers eliminate the external PHY and 12 MHz crystal that classic 8051 designs required, shrinking PCB area by roughly 30 percent. The 32 MHz core executes the USB stack polling loop in well under the 1 ms USB frame budget, leaving MIPS headroom for application code.
Empfohlen
USB CDC Virtual COM Port
For USB-to-serial bridge designs, the PIC24FJ64GB004T-I/PT acts as a CDC ACM device that appears as a COM port on a host PC. The integrated USB transceiver and 64 KB of Flash hold the CDC class driver plus application-level protocol handling, while the 8 KB RAM buffers full-speed bulk transfers without flow-control glitches. The 33 I/O pins expose UART, SPI, and I2C pins to bridge legacy microcontrollers, sensors, or industrial equipment to USB hosts. The 2.0-3.6 V VDD range permits direct battery-powered deployment, and nanoWatt XLP sleep mode draws less than 1 uA when the host suspends the bus.
Empfohlen
USB Mass Storage Devices
Engineers building USB flash drives, SD-card readers, or data-logger export dongles benefit from the PIC24FJ64GB004T-I/PT's USB Mass Storage Class (MSC) bulk-only transport support. The 64 KB Flash stores the MSC BOT state machine plus FAT16/32 file-system driver, and the 8 KB RAM handles 512-byte SCSI block transfers at full-speed USB throughput. SPI or parallel interfaces connect to NAND/SD media, while the 32 MHz CPU keeps the BOT handler comfortably below the 1 ms USB frame budget. NanoWatt XLP sleep mode cuts idle current under 1 uA for battery-powered portable storage devices.
Empfohlen
Industrial Sensor Interface Module
The PIC24FJ64GB004T-I/PT's 13-channel 10-bit ADC, 3 analog comparators, 5 PWM channels, and 7 timers cover the typical signal-conditioning needs of an industrial sensor interface. The 64 KB Flash holds Modbus RTU or CANopen protocol stacks, while the 8 KB RAM buffers multiple sensor readings before transmission. The -40C to +85C industrial temperature grade and 2.0-3.6 V VDD range operate reliably in factory cabinets. The USB OTG port enables field-service technicians to connect a tablet for diagnostics and firmware updates without opening the enclosure.
Empfohlen
Battery-Powered Data Logger
With nanoWatt XLP deep-sleep current below 1 uA, the PIC24FJ64GB004T-I/PT enables multi-year battery life in unattended data loggers that wake periodically to sample sensors. The integrated RTCC schedules wake events with calendar accuracy, while the 64 KB Flash stores several weeks of compressed time-stamped samples. The 2.0-3.6 V VDD range accommodates direct Li-ion or 2xAA battery operation across discharge. USB OTG enables field data extraction to a phone or tablet without removing the battery.
Empfohlen
Consumer Audio Accessory
Audio accessories such as USB headsets, DAC dongles, and MIDI controllers leverage the PIC24FJ64GB004T-I/PT for USB Audio Class 1.0 device implementation. The 33 I/O pins drive I2S/I2C codecs, button inputs, and LED indicators, while the 5 PWM channels produce visual feedback or motor control. The 64 KB Flash stores USB Audio class descriptors plus DSP filters, and the 32 MHz CPU sustains 48 kHz stereo sample flow over USB isochronous endpoints. NanoWatt XLP sleep mode saves power when the host suspends audio streaming.
Empfohlen
Educational / Development Board Platform
The PIC24FJ64GB004T-I/PT is the canonical MCU for Microchip's Explorer 16/32 development board PIMs, giving students and engineers a fully-documented 16-bit platform with USB connectivity, RTCC, ADC, PWM, and timers exposed via on-board peripherals. The C-compiler-optimized PIC24 instruction set and free MPLAB X IDE plus XC16 compiler provide a low-cost learning path from 8-bit PIC to 32-bit ARM. The 64 KB Flash accommodates moderate-sized projects with bootloader support, while 8 KB RAM runs a small RTOS for multitasking exercises.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC24FJ64GB004T-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC24FJ64GB004-I/PT | PIC24FJ32GB004T-I/PT | PIC24FJ64GA004T-I/PT | PIC24FJ64GB004T-I/ML | PIC24FJ64GB004T-E/PT |
|---|---|---|---|---|---|---|
| Package | 44-TQFP (10x10 mm) | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-QFN (8x8 mm) - different | 44-TQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 64 KB | 32 KB | 64 KB | 64 KB | 64 KB |
| RAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| USB OTG | Yes (Full-Speed) | Yes (Full-Speed) | Yes (Full-Speed) | No | Yes (Full-Speed) | Yes (Full-Speed) |
| CPU Speed | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS |
| Operating Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +125C (Extended) |
| I/O Pins | 33 | 33 | 33 | 33 | 33 | 33 |
| nanoWatt XLP | Yes | Yes | Yes | Yes | Yes | Yes |
| Packaging | Tape & Reel | Tray | Tape & Reel | Tape & Reel | Tape & Reel | Tape & Reel |
Wichtigste Unterscheidungsmerkmale
- Integrated USB 2.0 Full-Speed OTG transceiver (vs. PIC24FJ64GA004T-I/PT)
- 64 KB Flash vs 32 KB competitors in same package (vs. PIC24FJ32GB004T-I/PT)
- Industrial temperature grade with full peripheral set (vs. PIC24FJ64GB004T-E/PT)
- TQFP package for hand-soldering and prototyping (vs. PIC24FJ64GB004T-I/ML)
Designhinweise
Place a 0.1 uF ceramic decoupling capacitor within 3 mm of every VDD/VSS pin pair on the PIC24FJ64GB004T-I/PT, and add a bulk 10 uF tantalum or ceramic cap near the package. The USB VUSB pin (pin 36) requires its own 0.1 uF decoupling cap to stabilize the internal 3.3 V USB transceiver regulator. Operating voltage range is 2.0 V to 3.6 V; the USB module is not specified below 3.0 V per the datasheet. When USB is unused, leave VUSB floating and disable the USB module in firmware to save 200 uA.
Route the USB D+ (pin 37) and D- (pin 38) traces as a 90 ohm differential pair with length matching within 2 mm, keep them short (under 50 mm total), and surround them with a continuous ground pour referenced to VSS. Per the USB 2.0 specification, the differential impedance must be 90 ohms +/- 10 percent to comply with full-speed signaling. Avoid routing the differential pair near clock traces, switching regulators, or other high-frequency signals to minimize radiated EMI.
Always configure the CONFIG words (FOSC, FWDT, FPOR, etc.) before the device executes user code; an incorrect PLL or oscillator setting can lock the MCU out of In-Circuit Serial Programming (ICSP). The MCLR pin (pin 43) must be pulled high through a 10 kohm resistor for normal operation; leaving it floating causes intermittent resets. When migrating from the PIC24FJ64GB004-I/PT (tray) to the PIC24FJ64GB004T-I/PT (tape and reel), verify your pick-and-place feeder accepts 7-inch reels before scheduling production.
For the 44-pin TQFP (10x10 mm), allocate at least 0.5 mm clearance between package edges and adjacent traces to avoid solder-bridging. Use a 4-layer PCB with a dedicated ground plane on layer 2 for best EMI performance; on 2-layer boards, stitch the ground pours with vias every 5 mm. The exposed thermal pad is not present on this TQFP package, but a 10x10 mm copper pour under the part still reduces thermal stress by 5-8 C under heavy peripheral load.
Pin 43 is the MCLR reset input; ensure the 10 kohm pull-up resistor sits within 10 mm of the pin and that no high-current traces route nearby to prevent false resets from EMI. The OSC1/OSC2 crystal pins (41 and 42) should be guarded by a ground ring and the crystal traces kept under 5 mm to minimize parasitic capacitance. For noisy environments, place a 1 Mohm resistor across the crystal to start oscillation reliably across the full -40C to +85C range.
Compliance-Informationen
RoHS and REACH compliant per Microchip product page. Lead-free reflow profile per JEDEC J-STD-020. The I-suffix denotes Industrial -40C to +85C; this part is not AEC-Q100 qualified - choose the E-suffix for extended temperature or qualified automotive-grade parts.
