PIC24FJ64GC006-I/PT - 16-bit 32MHz 64KB Flash MCU | Microchip
Teilenummer: PIC24FJ64GC006-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $5.92 | $5,92 |
| 10 | $5.32 | $53,20 |
| 100 | $4.71 | $471,00 |
| 500 | $4.12 | $2.060,00 |
| 1.000 | $3.68 | $3.680,00 |
PIC24FJ64GC006-I/PT Übersicht
A 16-bit PIC microcontroller is a member of the microcontroller (MCU) product family that uses a 16-bit modified Harvard RISC architecture to deliver higher code density and faster arithmetic than 8-bit cores, while retaining the deterministic interrupt behaviour of the PIC heritage. The PIC24FJ sub-family adds eXtreme Low Power technology, USB connectivity options, and dedicated Intelligent Analog blocks that let designers build sensor interfaces without external ADC or op-amp ICs.
Key features of the PIC24FJ64GC006-I/PT include integrated op-amps and DAC for active sensor conditioning, a segmented LCD driver supporting up to 128 segments, USB On-The-Go with internal transceiver, and multiple communication peripherals (UART, SPI, I2C). The 12-bit pipeline ADC runs at up to 500 ksps while the 16-bit Sigma-Delta ADC delivers high-precision measurements at lower sample rates - ideal for weighing scales, temperature sensors, and strain gauges. The XLP Sleep current of typically under 100 nA in RTCC mode enables years of battery life in always-on systems.
Architecturally, the part uses a single-cycle 16-bit ALU, hardware multiply/divide, and a deterministic interrupt controller with 5-cycle latency, ensuring predictable response in real-time control loops. The PIC24F core can execute most instructions in one instruction cycle, providing 16 MIPS at 32 MHz - sufficient for USB stacks, sensor fusion, and human-interface firmware simultaneously.
Typical applications include portable medical devices (glucometers, pulse oximeters), industrial sensor transmitters, USB-based data loggers, electronic weighing scales, and consumer human-interface products with LCD readouts. The 64-pin TQFP footprint supports easy prototyping and is the same land pattern used across much of the PIC24FJ64/128 Gx family.
When designing with this part, ensure the 2.5 V or 3.3 V supply rail is well-decoupled with at least 100 nF close to each VDD/VSS pair, and that the analog and digital sections are routed on separate ground planes converging only at the IC's GND pins. For USB applications the internal transceiver requires a 2.2 kΩ pull-up on D+ and the data-line series resistors per USB specifications.
This page synthesises distributor pricing, drop-in alternatives in the same TQFP-64 footprint, and practical design notes not collated in the manufacturer datasheet alone, giving the engineer a single source for parametric, commercial, and engineering context on the PIC24FJ64GC006-I/PT.
Drop-in-Alternativen für PIC24FJ64GC006-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC24FJ64GC006-I/PT (gleiche Bauform und Footprint) – abweichend in Package, USB, Core Architecture, Operating Temperature, Program Memory (Flash).
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC24FJ128GC006-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24FJ128GC006T-I/PT
✅ Drop-In✓ Auf Lager
$4.9 / Stück
Datenblatt ansehen →PIC24FJ64GC006-I/MR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24FJ64GB106-I/PT
✅ Drop-In✓ Auf Lager
$3.18 / Stück
Datenblatt ansehen →PIC24FJ64GA006-I/PT
✅ Drop-In✓ Auf Lager
$4.61 / Stück
Datenblatt ansehen →PIC24FJ64GC006-I/PT Grenzwerte & elektrische Eigenschaften
| Core Architecture | PIC24F (16-bit RISC, modified Harvard) |
| Maximum CPU Frequency | 32 MHz (16 MIPS) |
| Program Flash Memory | 64 KB (22K x 24) |
| Data RAM | 8 KB |
| Operating Voltage Range | 2.0 V to 3.6 V |
| Typical Operating Voltages | 2.5 V or 3.3 V |
| Gehäuse | TQFP-64 (PT), 10x10 mm |
| Pin-Anzahl | 64 |
| Montageart | Surface Mount |
| ADC 1 | 12-bit pipeline, up to 500 ksps |
| ADC 2 | 16-bit Sigma-Delta |
| DAC Channels | Integrated |
| Op-Amps | Integrated |
| USB | USB On-The-Go (full-speed, internal transceiver) |
| LCD Driver | Segmented, up to 128 segments |
| eXtreme Low Power (XLP) Modes | Yes (Sleep current typically < 100 nA in RTCC mode) |
| Betriebstemperatur | -40C to +85C (industrial) |
| Temperature Grade | I (Industrial) |
| MSL-Level | MSL 3 (per JEDEC J-STD-020) |
| RoHS-Status | Compliant |
PIC24FJ64GC006-I/PT tqfp-64 (pt), 10x10 mm Pinbelegungsleitfaden
Pinbelegung für PIC24FJ64GC006-I/PT (tqfp-64 (pt), 10x10 mm-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für PIC24FJ64GC006-I/PT.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
PIC24FJ64GC006-I/PT ist geeignet für 6 Anwendungs: Portable Medical Devices (Glucometers, Pulse Oximeters), USB Data Loggers and Field Recorders, Electronic Weighing Scales, Industrial Sensor Transmitters (4-20 mA, IoT), Consumer Human-Interface Products with LCD, Battery-Powered IoT Edge Nodes.
Portable Medical Devices (Glucometers, Pulse Oximeters)
The PIC24FJ64GC006-I/PT is engineered for battery-powered medical instruments where high-resolution sensing and ultra-low standby current are equally important. Its 16-bit Sigma-Delta ADC resolves µV-level signals from optical or electrochemical sensors while the integrated op-amps provide on-chip transimpedance and buffer stages - removing the need for an external analog front-end. The XLP Sleep current, typically below 100 nA with RTCC running, lets a glucometer idle for years on a single coin cell between patient tests. The 64-pin TQFP-64 footprint allows compact board layout next to a segmented LCD driven directly by the on-chip controller, reducing BOM cost for Class II medical products.
Empfohlen
USB Data Loggers and Field Recorders
The integrated USB 2.0 full-speed On-The-Go controller with internal transceiver makes the PIC24FJ64GC006-I/PT a one-chip solution for portable USB data loggers. The on-chip 12-bit 500 ksps pipeline ADC captures fast sensor events while the 64 KB Flash stores firmware and downloadable log buffers in-line with USB transfer requests. Designers can present the device as a USB mass-storage or HID device without external PHY, reducing the BOM to one IC plus connector. Combined with the 32 MHz / 16 MIPS PIC24F core, the MCU can service USB, log to internal Flash and stream over UART simultaneously, ideal for handheld environmental recorders and field service instruments.
Empfohlen
Electronic Weighing Scales
Weighing scale designs benefit from the PIC24FJ64GC006-I/PT's integrated 16-bit Sigma-Delta ADC and on-chip op-amps, which connect directly to a load-cell bridge without external instrumentation amplifiers. The 64 KB Flash hosts calibration tables and unit-conversion routines, while the 8 KB RAM buffers real-time tare, filter and display updates. The segmented LCD driver presents weight and unit readouts directly with no external display driver IC, simplifying the schematic. Low Sleep current lets the scale enter a 100 nA idle mode between measurements, prolonging battery life in portable retail and kitchen scale applications.
Empfohlen
Industrial Sensor Transmitters (4-20 mA, IoT)
For 24 V loop-powered industrial transmitters the PIC24FJ64GC006-I/PT provides 12-bit pipeline ADC and DAC channels to drive 4-20 mA loops via an external op-amp. Industrial-grade -40C to +85C temperature rating allows deployment in process plants, while the PIC24F XLP modes keep the quiescent draw low enough to meet NAMUR NE43 fault-level requirements. The TQFP-64 package gives easy access to all communication peripherals for HART, IO-Link or wireless add-on modules. Engineers often pair the MCU with an isolated DC-DC and a digital isolator, but the core MCU itself never needs cross-brand replacement because of Microchip's PIC24 roadmap.
Empfohlen
Consumer Human-Interface Products with LCD
Coffee machines, thermostats and kitchen appliances use the PIC24FJ64GC006-I/PT because it integrates segmented LCD, op-amps for keypad sensing, and a USB port for firmware update or service diagnostics. The 64-pin TQFP gives ample GPIO for buttons, encoders, motor-control PWM and a buzzer. With 64 KB Flash and 8 KB RAM the firmware can host a full menu system, EEPROM emulation tables and a USB device stack simultaneously. The XLP Sleep current lets battery-backed thermostats retain time and schedule for years on a coin cell while drawing negligible standby power.
Empfohlen
Battery-Powered IoT Edge Nodes
Edge sensors that wake periodically to read a value and transmit via UART or radio benefit from the PIC24FJ64GC006-I/PT's deep Sleep with RTCC retained at < 100 nA. The 16-bit Sigma-Delta ADC measures battery voltage and sensor signal precisely, while the 12-bit pipeline ADC handles burst sampling when needed. Designers can pair the part with a low-power radio like the MRF24J40 or a sub-GHz transceiver, with the PIC24F acting as MCU host. The 64 KB Flash holds IPv6/6LoWPAN or proprietary stacks, OTA bootloader, and application logic - all on a part designed for years of battery life in metering or environmental monitoring.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC24FJ64GC006-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC24FJ128GC006-I/PT | PIC24FJ128GC006T-I/PT | PIC24FJ64GC006-I/MR | PIC24FJ64GB106-I/PT | PIC24FJ64GA006-I/PT |
|---|---|---|---|---|---|---|
| Package | TQFP-64 (PT) 10x10 mm | TQFP-64 (PT) 10x10 mm - same | TQFP-64 (PT) 10x10 mm - same | TQFP-64 family - same | TQFP-64 (PT) 10x10 mm - same | TQFP-64 (PT) 10x10 mm - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Flash | 64 KB | 128 KB | 128 KB | 64 KB | 64 KB | 64 KB |
| Data RAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| USB On-The-Go | Yes (internal transceiver) | Yes | Yes | Yes | Yes | No |
| 16-bit Sigma-Delta ADC | Yes | Yes | Yes | Yes | No | No |
| Segmented LCD Driver | Yes (up to 128 seg) | Yes | Yes | Yes | No | No |
| Core Frequency | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) |
| Price @ qty 1 (USD, as of 2026-09-30) | 5.92 | 6.84 | 6.84 | 5.92 | 5.41 | 5.18 |
Wichtigste Unterscheidungsmerkmale
- On-chip 16-bit Sigma-Delta ADC plus 12-bit pipeline ADC (vs. PIC24FJ64GA006-I/PT)
- Segmented LCD driver up to 128 segments (vs. PIC24FJ64GB106-I/PT)
- XLP Sleep current below 100 nA with RTCC running (vs. PIC24FJ128GC006-I/PT)
Designhinweise
Estimated: at the maximum 32 MHz CPU clock and VDD = 3.3 V the PIC24FJ64GC006-I/PT typically draws ~ 30 mA with all peripherals active; in Sleep with RTCC the current drops below 100 nA. Use a 100 nF X7R decoupling capacitor on every VDD/AVDD pin pair plus a single 10 µF bulk capacitor near the IC. For USB applications ensure VUSB is tied to VDD through a ferrite bead to keep digital switching noise out of the analog rail.
Route the analog signals (Sigma-Delta inputs, op-amp outputs) over a continuous analog ground plane and keep digital switching traces away from the analog section. Place the Sigma-Delta reference decoupling capacitor within 3 mm of the REFOUT pin to avoid conversion errors. For USB, keep the D+/D- traces length-matched and no longer than 50 mm; place the 2.2 kΩ pull-up close to the D+ pin.
Do not assume the LCD driver and the USB OTG can both operate simultaneously at full bias; high-bias 1/4 LCD mode with USB active may exceed the part's power budget and cause brown-out. If both are required, lower the LCD bias to 1/2 or 1/3. Also note that the Sigma-Delta ADC's reference voltage must be stable - driving it from VDD without a buffer introduces 1/f noise into low-frequency measurements such as weighing scale readings.
Compliance-Informationen
RoHS and REACH compliant per Microchip product page. Industrial temperature grade only (-40C to +85C); not AEC-Q100 qualified. Conflict-minerals reporting compliant per Microchip standard policy.