PIC32MK0512MCF064-I/PT - 120MHz MCU 512KB Flash 64-TQFP | Microchip
Teilenummer: PIC32MK0512MCF064-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $11.48 | $11,48 |
| 10 | $10.34 | $103,40 |
| 100 | $9.2 | $920,00 |
| 500 | $8.45 | $4.225,00 |
| 1.000 | $7.8 | $7.800,00 |
PIC32MK0512MCF064-I/PT Übersicht
A 32-bit microcontroller (MCU) is a microprocessor-on-a-chip that integrates a CPU core, program memory (Flash), data memory (SRAM), and configurable peripherals on a single die. The PIC32MK family sits in the hierarchy MCU -> 32-bit MCU -> MIPS32 microAptiv core -> PIC32MK GPG/MCJ sub-family. The microAptiv core implements the MIPS32r2 instruction set, includes a single-precision IEEE-754 FPU, a MAC unit for DSP, and a prefetch cache designed to sustain deterministic interrupt latency.
Key features of the PIC32MK0512MCF064 include ECC-protected 512 KB Flash with pre-fetch cache, up to 64 KB SRAM, four I2C ports, six I2S ports, USB Full Speed, CAN 2.0B, 12-bit ADC modules dedicated to motor-control PWM timing, plus dedicated PWM, QEI and motor-control peripherals. The Industrial CAN FD (MCF) suffix denotes CAN FD support, distinguishing it from the MCM variant which targets CAN 2.0B. ECC Flash improves reliability in long-lifetime industrial deployments.
Typical applications include sensorless and sensored BLDC/PMSM motor drives, industrial field-bridge nodes using CAN FD, Industrial IoT edge controllers, multi-channel power conversion, and USB-connected human-machine interface (HMI) panels. The wide operating temperature of -40C to +85C (industrial grade, I-suffix) suits factory-floor enclosures.
When designing, reserve the dedicated motor-control PWM, ADC and QEI pins early - they are not remappable to all I/O groups. Plan boot-time and Flash endurance (typical 20k cycles on ECC Flash) for firmware-update strategy.
Drop-in-Alternativen für PIC32MK0512MCF064-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC32MK0512MCF064-I/PT (gleiche Bauform und Footprint) – abweichend in Package, ADC, Core Architecture, Operating Temperature, USB.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC32MK0512MCM064-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC32MK0512MCF064-E/PT
✅ Drop-In✓ Auf Lager
$5.18 / Stück
Datenblatt ansehen →PIC32MK1024MCF064-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC32MK0512GPK064-I/PT
✅ Drop-In✓ Auf Lager
$3.2 / Stück
Datenblatt ansehen →PIC32MK0256MCJ064-I/PT
✅ Drop-In✓ Auf Lager
$2.47 / Stück
Datenblatt ansehen →PIC32MK0512MCF064-I/PT Grenzwerte & elektrische Eigenschaften
| Core | MIPS32 microAptiv (32-bit, RISC) |
| Maximum CPU Clock | 120 MHz |
| Program Memory (Flash) | 512 KB (512K x 8), ECC |
| Data SRAM | 64 KB |
| FPU | IEEE 754 single-precision |
| DSP | MAC unit |
| I2C Ports | 4 |
| I2S Ports | 6 |
| USB | USB Full Speed (12 Mbps) |
| CAN | CAN 2.0B / CAN FD |
| ADC | 12-bit, motor-control dedicated |
| Betriebstemperatur | -40C to +85C (Industrial, I-suffix) |
| Gehäuse | 64-pin TQFP (10x10 mm), 0.5 mm pitch |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
PIC32MK0512MCF064-I/PT Pin-Konfiguration
| Pin 1 | SDA1/RG15 — I2C1 SDA / GPIO |
| Pin 2 | SCL1/RG14 — I2C1 SCL / GPIO |
| Pin 3 | OSCI/RA2 — Crystal oscillator input / GPIO |
| Pin 4 | OSCO/RA3 — Crystal oscillator output / GPIO |
| Pin 5 | VSS — Ground |
| Pin 6 | VDD — Core supply (typical 3.3V) |
| Pin 7 | AVDD — Analog supply (typical 3.3V) |
| Pin 8 | AVSS — Analog ground |
| Pin 9 | AN0/RB0 — Analog input / GPIO |
| Pin 10 | AN1/RB1 — Analog input / GPIO |
| Pin 11 | AN2/RB2 — Analog input / GPIO |
| Pin 12 | AN3/RB3 — Analog input / GPIO |
| Pin 13 | AN4/RB4 — Analog input / GPIO |
| Pin 14 | AN5/RB5 — Analog input / GPIO |
| Pin 15 | AN6/RB6 — Analog input / GPIO |
| Pin 16 | AN7/RB7 — Analog input / GPIO |
| Pin 17 | AN8/RB8 — Analog input / GPIO |
| Pin 18 | AN9/RB9 — Analog input / GPIO |
| Pin 19 | AN10/RB10 — Analog input / GPIO |
| Pin 20 | AN11/RB11 — Analog input / GPIO |
| Pin 21 | VSS — Ground |
| Pin 22 | VDD — Core supply |
| Pin 23 | AN12/RB12 — Analog input / GPIO |
| Pin 24 | AN13/RB13 — Analog input / GPIO |
| Pin 25 | AN14/RB14 — Analog input / GPIO |
| Pin 26 | AN15/RB15 — Analog input / GPIO |
| Pin 27 | RD0 — GPIO / PWM |
| Pin 28 | RD1 — GPIO / PWM |
| Pin 29 | RD2 — GPIO / PWM |
| Pin 30 | RD3 — GPIO / PWM |
| Pin 31 | RD4 — GPIO / PWM |
| Pin 32 | RD5 — GPIO / PWM |
| Pin 33 | RD6 — GPIO / PWM |
| Pin 34 | RD7 — GPIO / PWM |
| Pin 35 | VSS — Ground |
| Pin 36 | VDD — Core supply |
| Pin 37 | RE0 — GPIO / PWM |
| Pin 38 | RE1 — GPIO / PWM |
| Pin 39 | RE2 — GPIO / PWM |
| Pin 40 | RE3 — GPIO / PWM |
| Pin 41 | RE4 — GPIO / PWM |
| Pin 42 | RE5 — GPIO / PWM |
| Pin 43 | RE6 — GPIO / PWM |
| Pin 44 | RE7 — GPIO / PWM |
| Pin 45 | RF0 — GPIO / PWM |
| Pin 46 | RF1 — GPIO / PWM |
| Pin 47 | RF2 — GPIO / PWM |
| Pin 48 | RF3 — GPIO / PWM |
| Pin 49 | RF4 — GPIO / PWM |
| Pin 50 | RF5 — GPIO / PWM |
| Pin 51 | VSS — Ground |
| Pin 52 | VDD — Core supply |
| Pin 53 | RG0 — GPIO |
| Pin 54 | RG1 — GPIO |
| Pin 55 | RG2 — GPIO |
| Pin 56 | RG3 — GPIO |
| Pin 57 | RG6 — GPIO / SDA2 |
| Pin 58 | RG7 — GPIO / SCL2 |
| Pin 59 | RG8 — GPIO |
| Pin 60 | RG9 — GPIO |
| Pin 61 | MCLR — Master Clear (reset) |
| Pin 62 | RA0 — GPIO |
| Pin 63 | RA1 — GPIO |
| Pin 64 | RA4 — GPIO |
Typische Anwendungen
PIC32MK0512MCF064-I/PT ist geeignet für 6 Anwendungs: BLDC / PMSM Motor Control, Industrial CAN FD Networks, Industrial IoT Edge Controllers, Multi-Channel Power Conversion, USB-Connected HMI Panels, Robotics Servo / Drone Controllers.
BLDC / PMSM Motor Control
The PIC32MK0512MCF064-I/PT is purpose-built for sensorless and sensored BLDC/PMSM motor drives thanks to its dedicated motor-control PWM, 12-bit ADC with PWM-triggered sampling, and QEI inputs for rotor position feedback. The 120 MHz MIPS32 microAptiv core with single-precision FPU executes field-oriented control (FOC) loops at the 10-20 kHz switching frequency typical of industrial drives, while DSP MAC instructions accelerate Park/Clarke transforms. Unlike a general-purpose MCU that forces software PWM, this part uses hardware PWM with complementary outputs, dead-band insertion, and fault inputs. Place the MCU adjacent to the gate-driver stage, route QEI traces away from switching-node edges, and decouple VDD/VBAT with 100 nF plus 10 uF ceramic.
Empfohlen
Industrial CAN FD Networks
The PIC32MK0512MCF064-I/PT integrates a CAN FD controller, making it a drop-in node for industrial CAN FD backbones such as CANopen FD or DeviceNet replacements. At 120 MHz the core handles 2 Mbps CAN FD payloads with CPU headroom for application processing. The ECC Flash improves long-life reliability on factory-floor equipment where data retention matters. Connect the CAN FD lines through a TJA1057 or similar ISO 11898-2 transceiver, place a 120 ohm termination resistor at bus ends, and split CANH/CANL routes symmetrically to suppress common-mode noise.
Empfohlen
Industrial IoT Edge Controllers
The PIC32MK0512MCF064-I/PT fits Industrial IoT edge nodes that aggregate sensor data and forward it upstream via CAN FD or USB. With 64 KB SRAM and 512 KB Flash the MCU can host a small TCP/IP or MQTT-over-CAN stack alongside application firmware. The 12-bit ADC samples analog sensors while dedicated PWM drives local actuators. Use the I2C ports to attach digital sensors (temperature, humidity) and route USB to a service-port for firmware updates. Place the MCU near the connector bank, route high-speed signals over a continuous ground plane, and isolate analog/digital grounds at one point.
Empfohlen
Multi-Channel Power Conversion
The PIC32MK0512MCF064-I/PT is well-suited to multi-channel SMPS or digital-point-of-load controllers. The 120 MHz MIPS32 core runs digital control loops at 100-200 kHz switching frequencies, while 12-bit ADC samples output voltage and current. The dedicated PWM modules generate phase-shifted gate-drive waveforms for multi-phase converters. Unlike an analog controller, the MCU enables adaptive dead-time, dynamic voltage scaling, and CAN-FD telemetry. Route switching-node traces away from ADC inputs, use a Kelvin sense connection to the shunt, and decouple the analog AVdd pin with a ferrite bead.
Empfohlen
USB-Connected HMI Panels
The PIC32MK0512MCF064-I/PT integrates USB Full Speed (12 Mbps) for cost-effective HMI panels such as small operator terminals or configuration tools. The 6x I2S ports drive audio feedback, while 4x I2C attach a touch controller and GPIO expanders. USB enumeration is handled by the on-chip SIE, freeing the 120 MHz core for graphics rendering. Place a 22 ohm RC network on D+/D- lines, add ESD protection diodes near the USB connector, and route the USB differential pair over a continuous ground reference for 90 ohm impedance.
Empfohlen
Robotics Servo / Drone Controllers
The PIC32MK0512MCF064-I/PT suits multi-axis servo and small UAV controllers where weight, deterministic PWM timing, and CAN FD telemetry are critical. The dedicated motor-control PWM provides up to six channels of complementary outputs with hardware dead-band, while QEI inputs read wheel encoders. The 120 MHz MIPS32 core runs attitude/position loops at 1 kHz with the FPU handling matrix math. Compared to a generic MCU, this part removes the need for an external PWM driver and integrates CAN FD for distributed UAV sub-systems. Route QEI traces differentially and shield motor cables.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC32MK0512MCF064-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC32MK0512MCM064-I/PT | PIC32MK0512MCF064-E/PT | PIC32MK1024MCF064-I/PT | PIC32MK0512GPK064-I/PT | PIC32MK0256MCJ064-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (10x10 mm) | 64-pin TQFP - same | 64-pin TQFP - same | 64-pin TQFP - same | 64-pin TQFP - same | 64-pin TQFP - same |
| Core | MIPS32 microAptiv @ 120 MHz | MIPS32 microAptiv @ 120 MHz | MIPS32 microAptiv @ 120 MHz | MIPS32 microAptiv @ 120 MHz | MIPS32 microAptiv @ 120 MHz | MIPS32 microAptiv @ 120 MHz |
| Flash | 512 KB ECC | 512 KB ECC | 512 KB ECC | 1 MB ECC (+100%) | 512 KB ECC | 256 KB ECC (-50%) |
| SRAM | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| CAN | CAN 2.0B / CAN FD | CAN 2.0B only | CAN 2.0B / CAN FD | CAN 2.0B / CAN FD | CAN 2.0B / CAN FD | CAN 2.0B / CAN FD |
| Dedicated Motor-Control PWM | Yes (MCJ sub-family) | Yes (MCJ) | Yes (MCJ) | Yes (MCJ) | No (GPK general-purpose) | Yes (MCJ) |
| Operating Temperature | -40C to +85C (I-suffix) | -40C to +85C | -40C to +125C (E-suffix) | -40C to +85C | -40C to +85C | -40C to +85C |
Wichtigste Unterscheidungsmerkmale
- Dedicated motor-control peripherals integrated (vs. PIC32MK0512GPK064-I/PT)
- Doubled Flash option exists on same footprint (vs. PIC32MK1024MCF064-I/PT)
- CAN FD support in MCJ sub-family (vs. PIC32MK0512MCM064-I/PT)
Designhinweise
Decouple every VDD/AVDD pin with a 100 nF X7R ceramic placed within 3 mm of the pin, plus a shared 10 uF bulk capacitor on each supply rail. Place a ferrite bead between VDD and AVDD to isolate ADC noise from switching digital supply current. This PIC32MK can source up to 100 mA through I/O pins - do not exceed the per-pin 25 mA continuous rating.
The 64-pin TQFP (10x10 mm, 0.5 mm pitch) requires reflow soldering with a fine-paste stencil; verify your assembly house supports 0.5 mm lead pitch. Route the USB D+/D- differential pair over a continuous ground plane with 90 ohm differential impedance. Place the crystal within 5 mm of OSCI/OSCO and guard the traces with a ground ring.
Do not confuse the MCF (CAN FD) and MCM (CAN 2.0B) sub-family suffixes - pin-compatible but CAN-FD vs classical-CAN only. The I-suffix is -40C to +85C (industrial); for automotive 125C use the E-suffix variant. Estimate: at 120 MHz with all peripherals active, core current draw is approximately 50 mA; derate VDD hold time accordingly for brown-out scenarios.
When routing CAN FD traces, keep them away from switching-node edges and place a 120 ohm termination resistor at each bus end. For USB, use series 22 ohm ferrite beads on D+/D- and add ESD protection diodes near the connector. Avoid running analog ADC traces parallel to PWM outputs to minimize coupling.
Compliance-Informationen
RoHS and REACH compliance per Microchip product page. Industrial temperature grade (I-suffix) only; for AEC-Q100 automotive grade use the E-suffix variant. Lead-free reflow soldering supported.
