Skyworks Solutions

SI3019-F-GM Programmable Telecom DAA | Skyworks Solutions

Teilenummer: SI3019-F-GM ✓ Aktiv
3.3 V Vdss LCS2[7:0] Id 20 pins Package
MOQ: 1 |

SI3019-F-GM Übersicht

Skyworks Solutions SI3019-F-GM is a programmable telecom Direct Access Arrangement integrated circuit designed for globally compliant foreign exchange office analog interfaces. It supports 20-pin QFN packaging in a 3 mm × 3 mm footprint and operates from a 3.3 V supply according to the product listing. The SI3019 line-side device is used with the Si3050 controller in programmable Voice DAA solutions for telephone line interface and foreign exchange equipment.

A Direct Access Arrangement, or DAA, is the analog interface between a telephone line and a digital communications controller. It handles the line-side signaling and current-control functions required to connect digital equipment to a foreign exchange line. Within the equipment hierarchy, the DAA is an interface IC: the Si3050 interprets and generates protocol-level signaling, while the SI3019 provides the physical analog interface to the line.

The SI3019 family is designed for programmable voice DAA solutions. Its supporting device, the Si3050, can measure line voltage when paired with an SI3011 or SI3019 line-side device. The SI3019 additionally provides an LCS2 register that reports loop current at a finer resolution than the Si3050 can measure by itself. This division of responsibility supports firmware-configurable line monitoring in telephony systems.

Compliance and regional line behavior are central to this product category because telephone interfaces must operate across different line voltages, loop currents, and signaling conventions. The manufacturer describes the Si3050 and SI3011, SI3018, and SI3019 chipset as highly programmable and globally compliant. A compact 20-QFN package also supports space-constrained designs where a larger SOIC footprint would be undesirable.

Typical uses include foreign exchange office line cards, voice-over-IP terminal adapters, embedded telephony gateways, digital PBX interfaces, and other equipment that connects digital voice circuitry to an analog telephone line. The SI3019 is positioned at the line-facing edge of the circuit, while the Si3050 and surrounding system electronics perform control and signal processing.

Designers should treat the SI3019 and Si3050 as a coordinated chipset rather than selecting them independently. Review the manufacturer’s Si3050 and SI3011, SI3018, SI3019 datasheet for the complete pin list, electrical limits, application circuit, and layout requirements. The 3 mm × 3 mm QFN land pattern also requires careful thermal-pad, solder, and trace-layout implementation.

This page organizes the verified product identity, package information, chipset relationship, sourcing links, and engineering guidance around the SI3019-F-GM. It also distinguishes direct drop-in replacements from related package variants and identifies the decisions that must be checked before changing a telecom line-interface design.

Drop-in-Alternativen für SI3019-F-GM – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.

Alternativen anfordern

SI3019-F-GM Technische Daten

Product Type Telecom Direct Access Arrangement (DAA) IC
Device Family Si3019 line-side interface
Versorgungsspannung 3.3 V
Package Pin Count 20 pins
Package Type QFN (3 mm × 3 mm)
Interface Function Globally compliant foreign exchange office analog interface
Programmability Programmable voice DAA
Compatible Controller Si3050
Line Voltage Measurement Supported through Si3050 with Si3019
Loop Current Reporting Register LCS2[7:0]

SI3019-F-GM qfn (3 mm × 3 mm) Pinbelegungsleitfaden

Pinbelegung für SI3019-F-GM (qfn (3 mm × 3 mm)-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für SI3019-F-GM im qfn (3 mm × 3 mm)-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für SI3019-F-GM.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

SI3019-F-GM ist geeignet für 6 Anwendungs: Foreign Exchange Office Line Interfaces, Voice-over-IP Terminal Adapters, Digital PBX Line Cards, Embedded Telephony Gateways, Analog Voice Adapter Boards, Telephony Test and Measurement Equipment.

🌐

Foreign Exchange Office Line Interfaces

SI3019-F-GM fits the line-facing circuit in a foreign exchange office because it is designed as a programmable Direct Access Arrangement for globally compliant analog telephone interfaces. It is paired with the Si3050 controller, which handles higher-level line signaling and measurement functions while the SI3019 manages the analog line-side device role. Its 20-pin 3 mm × 3 mm QFN package also helps reduce board area in compact line cards. The SI3019 adds LCS2[7:0] loop-current reporting, enabling more detailed line-state monitoring than the Si3050 can perform alone when the line-side device is absent. Designers should implement the manufacturer’s recommended protection, grounding, and layout around the telephone-line interface and validate operation against the applicable country requirements.

📞

Voice-over-IP Terminal Adapters

SI3019-F-GM can provide the analog foreign exchange office interface in a voice-over-IP terminal adapter that must connect digital voice processing to a telephone line. The Si3050 controller and SI3019 line-side device divide the interface into digital control and physical line functions, allowing regional line behavior to be managed through programmable device configuration. The SI3019’s finer loop-current reporting through LCS2[7:0] is useful when firmware needs detailed line-state information for supervision, call control, or fault detection. Its compact 20-QFN package reduces the footprint compared with a larger leaded interface package. The final design should follow the manufacturer’s reference circuit, external line protection network, component spacing, and grounding guidance to preserve signal integrity at the line boundary.

🏢

Digital PBX Line Cards

SI3019-F-GM is appropriate for a digital private branch exchange line card requiring a programmable foreign exchange office interface. The device works with the Si3050 so that the board can combine digital control and analog line-side functions without relying solely on a fixed-function interface circuit. Compactness is valuable in multi-channel line-card designs because the SI3019 uses a 20-pin QFN measuring 3 mm × 3 mm rather than a larger leaded outline. Fine-resolution loop-current information from LCS2[7:0] can support line supervision and fault-management firmware. Because every line interface introduces surge and ESD exposure, the implementation should include the manufacturer-recommended protection components and maintain the required separation between line-side and system-side circuitry.

🔧

Embedded Telephony Gateways

SI3019-F-GM supports embedded gateways that bridge a digital voice subsystem to an analog telephone line. Its programmable DAA architecture allows the Si3050-based design to adapt line supervision and signaling behavior through firmware rather than relying on a fixed regional interface. The line-side SI3019 also supplies finer loop-current reporting than the Si3050 can obtain independently, which can improve supervisory decisions and diagnostic granularity. A 20-pin 3 mm × 3 mm QFN helps gateways include legacy telephone connectivity without consuming excessive board area. Implementation should closely follow the manufacturer’s reference design for the line interface, including protection, grounding, clocking, and digital-interface routing. Production validation should cover the line voltage, loop current, and signaling requirements applicable to each deployment region.

📡

Analog Voice Adapter Boards

SI3019-F-GM is suitable for small analog voice adapter boards that add foreign exchange office connectivity to a digital processor or communications module. Pairing it with the Si3050 creates a dedicated line-interface path rather than burdening the host processor with low-level analog telephone signaling. The SI3019’s 20-pin QFN package supports compact adapter hardware, while LCS2[7:0] supplies detailed loop-current information to host-directed firmware. This information can be used to improve line-state detection, supervision, and maintenance diagnostics. Board designers should preserve the manufacturer’s recommended line protection, maintain suitable isolation and separation between the line and logic domains, and use a PCB stack-up capable of supporting the small QFN land pattern and exposed-pad assembly process.

🧰

Telephony Test and Measurement Equipment

SI3019-F-GM can be integrated into telephony test equipment that must emulate or monitor a programmable foreign exchange office line. The Si3050 and SI3019 chipset provides the interface architecture needed to exercise line-side behavior while the SI3019’s finer loop-current reporting assists measurement and diagnosis. This makes the pair useful for equipment designers developing line-state test routines, supervision checks, or interoperability test systems. The compact 20-pin 3 mm × 3 mm QFN also allows the interface to be placed close to the line connector and protection network. For accurate results, follow the manufacturer’s grounding and application-circuit guidance, account for line-side protection delays, and calibrate the measurement path against the specified line voltage and loop-current ranges.

Zusammenfassung der empfohlenen Produkte

Si3050 Controller paired with the SI3019 line-side DAA Verwendet in: Foreign Exchange Office Line Interfaces, Voice-over-IP Terminal Adapters, Digital PBX Line Cards, Embedded Telephony Gateways, Analog Voice Adapter Boards, Telephony Test and Measurement Equipment SI3011 Related Si3050 line-side DAA family member Verwendet in: Foreign Exchange Office Line Interfaces, Voice-over-IP Terminal Adapters, Embedded Telephony Gateways, Analog Voice Adapter Boards SI3018 Related programmable voice DAA family member Verwendet in: Foreign Exchange Office Line Interfaces, Voice-over-IP Terminal Adapters, Digital PBX Line Cards, Analog Voice Adapter Boards, Telephony Test and Measurement Equipment
What is SI3019-F-GM?
SI3019-F-GM is a programmable line-side Direct Access Arrangement integrated circuit from Skyworks Solutions for foreign exchange office and analog telephone-line interfaces. According to the manufacturer datasheet for the Si3050, Si3011, Si3018, and Si3019 family, the SI3019 works with the Si3050 controller and is packaged as a 20-pin QFN in a 3 mm × 3 mm footprint.
What are the key specifications of SI3019-F-GM that engineers should know?
SI3019-F-GM is a 3.3 V, 20-pin QFN line-side DAA used with the Si3050 controller. According to the manufacturer’s programmable voice DAA datasheet, it supports globally compliant foreign exchange office interfaces and adds an LCS2[7:0] register for finer loop-current reporting. The Si3050 can measure line voltage when paired with the SI3019, while the SI3019 handles the analog line-side interface.
Which controller works with SI3019-F-GM?
The Si3050 is the controller specified for use with SI3019-F-GM. According to the Skyworks Solutions Si3050, Si3011, Si3018, Si3019 datasheet, the Si3050 can measure line voltage when used with an SI3011 or SI3019 line-side device. Treat the Si3050 and SI3019 as a coordinated chipset so that firmware, pin connections, and line-interface functions remain matched.
Where can I download the SI3019-F-GM datasheet PDF?
The official SI3019-F-GM chipset datasheet is available from Skyworks Solutions at the product’s manufacturer PDF link on this page. It is titled “Si3050-11-18-19” and covers the Si3050, Si3011, Si3018, and Si3019 programmable voice DAA solutions. Use that document for the authoritative pin descriptions, electrical characteristics, line-interface parameters, and application circuit.
Where can I find the SI3019-F-GM pinout?
Use the pin-description table and package drawing in the manufacturer’s Si3050-11-18-19 datasheet for the SI3019-F-GM pinout. The device is identified as a 20-pin QFN package measuring 3 mm × 3 mm. The manufacturer document is the controlling reference for signal names, exposed-pad treatment, and board-level connections; consult it before assigning PCB tracks.
Where can I buy SI3019-F-GM and request a quotation?
Use the Request a Quote form on this page to ask about SI3019-F-GM availability, order quantities, and delivery timing. The form is the appropriate route for a current quotation rather than relying on a historical catalog figure. The part is listed as a 20-QFN telecom DAA by Skyworks Solutions, and its ordering suffix and package must be confirmed as part of the request.
What is the current lead time for SI3019-F-GM?
The current SI3019-F-GM lead time should be requested through the Request a Quote form on this page. Lead time depends on order quantity, package suffix, manufacturing availability, and shipment destination. Do not substitute the minimum order quantity mentioned for related SI3019 package variants, because each ordering code can have different supply conditions.
Is SI3019-F-GM currently in stock?
Current SI3019-F-GM inventory should be confirmed through the Request a Quote form on this page. Historical listing pages do not establish present-day stock for an exact ordering code. When requesting a quotation, specify SI3019-F-GM, the required quantity, and the intended delivery location so the response reflects the current supply position.
SI3019-F-GM vs SI3019-F-GSR: which package should I use?
SI3019-F-GM is identified as a 20-pin QFN in a 3 mm × 3 mm package, while SI3019-F-GSR is described as a line-side DAA intended for a Si3050 SOIC arrangement. The visible package descriptions therefore indicate different PCB land patterns. SI3019-F-GSR should not be treated as a drop-in replacement for SI3019-F-GM unless the complete pinout and ordering documentation demonstrate otherwise.
What is the difference between SI3019-F-GM and SI3019-F-GSR?
The principal verified difference is package format: SI3019-F-GM is a 20-pin QFN in a 3 mm × 3 mm footprint, whereas SI3019-F-GSR is listed as a global line-side DAA for a Si3050 SOIC arrangement. The two ordering codes also appear in different lifecycle notices, so their order status and supply terms should be checked independently. They are not treated as confirmed drop-in alternatives here.
When should I choose SI3019-F-GM over SI3019-F-GSR?
Choose SI3019-F-GM when the PCB is designed around the 20-pin 3 mm × 3 mm QFN footprint and the design uses the Si3050 with an SI3019 line-side device. Choose SI3019-F-GSR only when the board specifically supports its SOIC arrangement and its ordering status is acceptable. Because the verified package descriptions differ, PCB footprint compatibility should determine the choice before software or supply considerations.
Is SI3019-F-GM suitable for foreign exchange office equipment?
SI3019-F-GM is specifically suited to foreign exchange office equipment because it is a programmable line-side DAA designed for globally compliant analog interfaces. According to the Skyworks Solutions chipset datasheet, it works with the Si3050 controller and supports fine-resolution loop-current reporting through LCS2[7:0]. Final compliance still depends on the complete line interface, country-specific requirements, and production test configuration.
What can replace SI3019-F-GM?
No confirmed drop-in replacement for SI3019-F-GM was established from the manufacturer and cross-reference information reviewed for this page. Related SI3019 ordering codes, including SI3019-F-GSR, are associated with different package descriptions and therefore cannot automatically replace the 20-QFN device. A valid replacement must match the complete pinout, electrical limits, Si3050 interface, line-side behavior, and PCB land pattern.
Is SI3019-F-GM the same as SI3019-F-GSR?
No. SI3019-F-GM and SI3019-F-GSR have different documented package formats: SI3019-F-GM is a 20-pin 3 mm × 3 mm QFN, while SI3019-F-GSR is described for a Si3050 SOIC arrangement. They belong to the broader SI3019 line-side family, but family membership alone does not establish pin-to-pin compatibility. Do not substitute one without a complete footprint and pinout comparison.
Is there a Silicon Labs equivalent for SI3019-F-GM?
SI3019-F-GM was originally associated with Silicon Labs product documentation and is now listed by Skyworks Solutions, so historical manufacturer attribution should not be interpreted as a separate interchangeable device. No independent cross-brand part with a verified identical QFN footprint, pinout, electrical limits, and Si3050 compatibility was identified. Treat another manufacturer’s DAA as a redesign candidate unless formal equivalence documentation is available.
How should the SI3019-F-GM QFN footprint be laid out?
Follow the land pattern, exposed-pad connection, and solder-process recommendations in the manufacturer’s Si3050-11-18-19 datasheet. The SI3019-F-GM uses a 20-pin QFN measuring 3 mm × 3 mm, so placement tolerances and thermal-pad assembly details are critical. Keep line-side and sensitive signal paths away from noisy switching nodes, and verify clearances and grounding against the reference design.
What standards and compliance documents apply to SI3019-F-GM?
The verified manufacturer material describes the Si3019 platform as providing a globally compliant foreign exchange office interface, but no specific RoHS, REACH, AEC-Q100, ITU, or national telephone-network compliance document was identified for this exact ordering code. Confirm product compliance and country-specific line-interface requirements with the manufacturer before release. Treat broad “globally compliant” wording as a platform description rather than a substitute for formal certification records.

Technische Referenzdaten für SI3019-F-GM – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose SI3019-F-GM for a compact design that uses the Si3050 controller with a 20-pin, 3 mm × 3 mm QFN line-side DAA. Its coordinated Si3050 relationship provides a clearly defined architecture for programmable foreign exchange office interfaces, while LCS2[7:0] adds finer loop-current reporting than the Si3050 can perform alone. Related SI3019 ordering codes are not automatic replacements because package descriptions and ordering conditions can differ. In particular, SI3019-F-GSR is associated with a Si3050 SOIC arrangement rather than the SI3019-F-GM QFN footprint. Before approving a substitution, compare the exact pinout, package drawing, exposed-pad connection, electrical limits, line voltage and loop-current ranges, and Si3050 firmware expectations. For a new design, prefer SI3019-F-GM when its footprint and supply arrangement match the board and the manufacturer’s chipset guidance can be followed without creating a footprint conversion.

Vergleich mit Alternativen

Parameter Dieses Produkt
Package 20-QFN (3 mm × 3 mm)
Brand Skyworks Solutions
Product Type Programmable Direct Access Arrangement IC
Supply Voltage 3.3 V
Pin Count 20 pins
Primary Controller Si3050
Line-Side Loop-Current Reporting LCS2[7:0]
Interface Function Globally compliant foreign exchange office analog interface
Mounting Type Surface mount

Designhinweise

Implement the 20-pin QFN land pattern, exposed-pad connection, and solder mask geometry exactly as shown in the manufacturer’s package drawing and recommended land pattern. Place the SI3019 close to the line-side protection and connector network, but preserve the required separation between the telephone-line domain and low-level digital circuitry. Review the pad geometry and assembly process with the selected PCB manufacturer because the compact 3 mm × 3 mm outline leaves limited tolerance for placement and solder-joint inspection errors.

Keep the SI3019-to-Si3050 interface routing short, controlled, and away from switching nodes and high-current return paths. Use a continuous ground reference beneath the device where the recommended layout permits it, and route sensitive line-side nodes away from unrelated high-slew-rate signals. Confirm the final layer stack, via placement, and return-current paths against the manufacturer reference design before releasing the PCB because the small QFN package offers limited room for post-layout corrections.

Do not treat SI3019-F-GM as interchangeable with related SI3019 ordering codes solely because their names are similar. SI3019-F-GM is identified as a 20-pin QFN, whereas SI3019-F-GSR is described for a Si3050 SOIC arrangement. Before substituting any variant, compare its complete ordering code, package drawing, pin names, electrical limits, line-side behavior, exposed-pad requirements, and controller compatibility. A functional description alone is not evidence of a pin-to-pin drop-in replacement.

Apply the manufacturer’s recommended telephone-line protection and filtering network before the SI3019 inputs. Surge and transient events originate at the external line, so protection placement and return-current paths are as important as the IC selection. Keep protective-current paths away from the Si3050 and SI3019 control signals, and validate both normal line activity and injected transients in the final board because parasitic inductance can defeat an otherwise correct schematic.

Power the SI3019-F-GM from the specified 3.3 V system supply and follow the manufacturer’s decoupling and sequencing requirements. Place the recommended input capacitors directly beside their associated supply and ground pins, with short and wide return paths. Confirm the Si3050 and SI3019 clock, reset, and interface requirements as a complete chipset, and verify supply tolerance and sequencing at the system level rather than checking only the nominal operating point.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The manufacturer describes the chipset as providing globally compliant foreign exchange office interfaces, but exact RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification records were not identified for SI3019-F-GM. AEC-Q100 is not applicable because this is a telecom interface IC rather than an automotive-qualified device.

Daten verifiziert am: 2026-11-20 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

si3019 f ftr SI3019-F-GM datasheet SI3019-F-GM datasheet pdf SI3019-F-GM pinout SI3019-F-GM equivalent SI3019-F-GM replacement SI3019-F-GM vs SI3019-F-GSR SI3019-F-GM QFN-20 footprint SI3019-F-GM 3.3V DAA Skyworks Solutions SI3019-F-GM SI3019-F-GM foreign exchange office SI3019-F-GM price SI3019-F-GM stock

Verwandte Bauteile & Begriffe

Skyworks Solutions Silicon Labs SI3019-F-GM SI3019 Si3050 SI3011 SI3018 SI3019-F-GSR Direct Access Arrangement DAA foreign exchange office FXO programmable voice DAA line-side interface analog telephone line loop current LCS2[7:0] line voltage QFN-20 QFN family surface mount 3.3 V power supply telecom interface IC voice-over-IP
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen