STM32F105VCT6 - 72MHz Cortex-M3 MCU, 256KB Flash, USB OTG | ST
Teilenummer: STM32F105VCT6| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $9.2 | $9,20 |
| 10 | $8.45 | $84,50 |
| 100 | $7.4 | $740,00 |
| 500 | $6.65 | $3.325,00 |
| 1.000 | $5.95 | $5.950,00 |
| 2.500 | $5.4 | $13.500,00 |
STM32F105VCT6 Übersicht
A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory (typically Flash), data memory (SRAM), and a rich set of peripherals (timers, ADC, communication interfaces) onto one silicon die. MCUs sit at the heart of nearly every embedded system - from industrial PLCs and motor drives to consumer appliances and IoT edge nodes - executing deterministic real-time firmware that reads sensors and drives actuators. The Cortex-M3 architecture from ARM is a 32-bit RISC core designed for low-latency interrupt response, deterministic bit-manipulation, and high code density through the Thumb-2 instruction set.
Key features include a 72 MHz max CPU clock with single-cycle multiply and hardware divide, USB 2.0 Full-Speed OTG with on-chip PHY, two CAN 2.0B active interfaces, 10/100 Ethernet MAC (MII/RMII), up to 5 USARTs, 3 SPI, 2 I2C, a 1-mbx2C I2S, two 12-bit ADCs (1 Msps, 16 channels), one 12-bit DAC, plus an FSMC bus for external memory or parallel display. The 100-pin LQFP exposes 80+ GPIO across multiple 5V-tolerant banks, supporting flexible mixed-signal designs.
The part uses an internal 8 MHz RC and an optional 32.768 kHz LSE crystal for the RTC. Power is managed through three low-power modes (Sleep, Stop, Standby) with a typical run current of ~30 mA at 72 MHz and stop current below 50 uA. The 2.0V to 3.6V supply range supports both 3.3V and battery-backed designs.
Typical applications include industrial gateways with USB or CAN, USB HID/COM port devices, RS485/CAN industrial sensor nodes, motor control boards using CAN and timers, point-of-sale terminals, low-cost Ethernet-equipped embedded nodes, and human-machine interface panels driving LCDs through FSMC. Designers pick the F105 over the F103 when they need USB OTG host capability, dual CAN, or an integrated Ethernet MAC on the same die.
When designing with this MCU, allocate the FSMC bus carefully if you add an external SRAM or NOR Flash, since pin remapping can clash with timers and USARTs. Use ST's STM32CubeMX to validate alternate-function mapping before final layout, and check the errata sheet for early-revision silicon behavior on the Ethernet MAC and USB OTG PHY.
This page synthesizes distributor pricing, parametric alternatives, and practical design notes beyond the manufacturer datasheet to support BOM decisions and second-source planning.
Drop-in-Alternativen für STM32F105VCT6 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit STM32F105VCT6 (gleiche Bauform und Footprint) – abweichend in Timers, ADC, Package, USB, I2C.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
STM32F105RCT6
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$4.85 / Stück
Datenblatt ansehen →STM32F107VCT6
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$6.95 / Stück
Datenblatt ansehen →STM32F103VCT6
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$2.68 / Stück
Datenblatt ansehen →GD32F105VCT6
✅ Drop-In✓ Auf Lager
$1.55 / Stück
Datenblatt ansehen →STM32F105VCT7
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$7.65 / Stück
Datenblatt ansehen →STM32F105VBT6
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
STM32F105VCT6 Grenzwerte & elektrische Eigenschaften
| Core Architecture | ARM Cortex-M3 (32-bit) |
| Core Max Frequency | 72 MHz |
| Program Memory (Flash) | 256 KB |
| SRAM | 64 KB |
| Operating Voltage (VDD) | 2.0 V to 3.6 V |
| Gehäuse | LQFP-100 (14x14 mm) |
| Betriebstemperatur | -40 C to +85 C |
| GPIO Count | 80+ |
| USB | USB 2.0 Full-Speed OTG with on-chip PHY |
| CAN | 2x CAN 2.0B active |
| Ethernet | 10/100 MAC (MII/RMII) - external PHY required |
| USART/UART | 5 channels |
| SPI | 3 channels |
| I2C | 2 channels |
| ADC | 2x 12-bit, 1 Msps, 16 channels |
| DAC | 1x 12-bit |
| Timers | Advanced-control, general-purpose, basic, SysTick, watchdog |
| FSMC | Yes - external memory/display bus |
| DMA | 12 channels |
| RoHS-Status | Compliant |
STM32F105VCT6 Pin-Konfiguration
| Pin 1 | PE2 — GPIO PE2 / TRACECLK |
| Pin 2 | PE3 — GPIO PE3 / TRACED0 |
| Pin 3 | PE4 — GPIO PE4 / TRACED1 |
| Pin 4 | PE5 — GPIO PE5 / TRACED2 |
| Pin 5 | PE6 — GPIO PE6 / TRACED3 |
| Pin 6 | VBAT — RTC backup supply |
| Pin 7 | PC13 — GPIO PC13 / Tamper-RTC |
| Pin 8 | PC14 — GPIO PC14 / OSC32_IN |
| Pin 9 | PC15 — GPIO PC15 / OSC32_OUT |
| Pin 10 | VSS_1 — Ground |
| Pin 11 | VDD_1 — Digital supply 2.0-3.6 V |
| Pin 12 | OSC_IN — HSE crystal oscillator input |
| Pin 13 | OSC_OUT — HSE crystal oscillator output |
| Pin 14 | NRST — Reset (active low) |
| Pin 15 | PC0 — GPIO PC0 / ADC12_IN10 |
| Pin 16 | PC1 — GPIO PC1 / ADC12_IN11 |
| Pin 17 | PC2 — GPIO PC2 / ADC12_IN12 |
| Pin 18 | PC3 — GPIO PC3 / ADC12_IN13 |
| Pin 19 | VSSA — Analog ground |
| Pin 20 | VDDA — Analog supply 2.0-3.6 V |
| Pin 21 | PA0 — GPIO PA0 / WKUP / ADC12_IN0 / TIM2_CH1 |
| Pin 22 | PA1 — GPIO PA1 / ADC12_IN1 / TIM2_CH2 |
| Pin 23 | PA2 — GPIO PA2 / ADC12_IN2 / TIM2_CH3 / USART2_TX |
| Pin 24 | PA3 — GPIO PA3 / ADC12_IN3 / TIM2_CH4 / USART2_RX |
| Pin 25 | VSS_2 — Ground |
| Pin 26 | VDD_2 — Digital supply 2.0-3.6 V |
| Pin 27 | PA4 — GPIO PA4 / ADC12_IN4 / SPI1_NSS / USART2_CK |
| Pin 28 | PA5 — GPIO PA5 / ADC12_IN5 / SPI1_SCK / DAC_OUT1 |
| Pin 29 | PA6 — GPIO PA6 / ADC12_IN6 / SPI1_MISO / TIM3_CH1 |
| Pin 30 | PA7 — GPIO PA7 / ADC12_IN7 / SPI1_MOSI / TIM3_CH2 |
| Pin 31 | PC4 — GPIO PC4 / ADC12_IN14 |
| Pin 32 | PC5 — GPIO PC5 / ADC12_IN15 |
| Pin 33 | PB0 — GPIO PB0 / ADC12_IN8 / TIM3_CH3 |
| Pin 34 | PB1 — GPIO PB1 / ADC12_IN9 / TIM3_CH4 |
| Pin 35 | PB2 — GPIO PB2 / BOOT1 |
| Pin 36 | PE7 — GPIO PE7 |
| Pin 37 | PE8 — GPIO PE8 / TIM1_CH1N |
| Pin 38 | PE9 — GPIO PE9 / TIM1_CH1 |
| Pin 39 | PE10 — GPIO PE10 / TIM1_CH2N |
| Pin 40 | PE11 — GPIO PE11 / TIM1_CH2 |
| Pin 41 | PE12 — GPIO PE12 / TIM1_CH3N |
| Pin 42 | PE13 — GPIO PE13 / TIM1_CH3 |
| Pin 43 | PE14 — GPIO PE14 / TIM1_CH4 |
| Pin 44 | PE15 — GPIO PE15 / TIM1_BKIN |
| Pin 45 | PB10 — GPIO PB10 / I2C2_SCL / USART3_TX |
| Pin 46 | PB11 — GPIO PB11 / I2C2_SDA / USART3_RX |
| Pin 47 | VSS_3 — Ground |
| Pin 48 | VDD_3 — Digital supply 2.0-3.6 V |
| Pin 49 | PB12 — GPIO PB12 / SPI2_NSS / I2S2_WS |
| Pin 50 | PB13 — GPIO PB13 / SPI2_SCK / I2S2_CK |
| Pin 51 | PB14 — GPIO PB14 / SPI2_MISO / TIM1_CH2N |
| Pin 52 | PB15 — GPIO PB15 / SPI2_MOSI / TIM1_CH3N |
| Pin 53 | PD8 — GPIO PD8 / USART3_TX / ETH_RMII_RX_DV |
| Pin 54 | PD9 — GPIO PD9 / USART3_RX / ETH_RMII_CRS_DV |
| Pin 55 | PD10 — GPIO PD10 |
| Pin 56 | PD11 — GPIO PD11 |
| Pin 57 | PD12 — GPIO PD12 / TIM4_CH1 |
| Pin 58 | PD13 — GPIO PD13 / TIM4_CH2 |
| Pin 59 | PD14 — GPIO PD14 / TIM4_CH3 |
| Pin 60 | PD15 — GPIO PD15 / TIM4_CH4 |
| Pin 61 | PC6 — GPIO PC6 / I2S2_MCK / TIM3_CH1 |
| Pin 62 | PC7 — GPIO PC7 / I2S2_CK / TIM3_CH2 |
| Pin 63 | PC8 — GPIO PC8 / TIM3_CH3 |
| Pin 64 | PC9 — GPIO PC9 / TIM3_CH4 |
| Pin 65 | PA8 — GPIO PA8 / USART1_CK / TIM1_CH1 / MCO |
| Pin 66 | PA9 — GPIO PA9 / USART1_TX / TIM1_CH2 |
| Pin 67 | PA10 — GPIO PA10 / USART1_RX / TIM1_CH3 |
| Pin 68 | PA11 — GPIO PA11 / USART1_CTS / CAN1_RX / USB_DM |
| Pin 69 | PA12 — GPIO PA12 / USART1_RTS / CAN1_TX / USB_DP |
| Pin 70 | PA13 — GPIO PA13 / JTMS / SWDIO |
| Pin 71 | VSS_4 — Ground |
| Pin 72 | VDD_4 — Digital supply 2.0-3.6 V |
| Pin 73 | PA14 — GPIO PA14 / JTCK / SWCLK |
| Pin 74 | PA15 — GPIO PA15 / JTDI / TIM2_CH1 / SPI1_NSS |
| Pin 75 | PC10 — GPIO PC10 / UART4_TX / SPI3_SCK |
| Pin 76 | PC11 — GPIO PC11 / UART4_RX / SPI3_MISO |
| Pin 77 | PC12 — GPIO PC12 / UART5_TX / SPI3_MOSI |
| Pin 78 | PD0 — GPIO PD0 / OSC_IN |
| Pin 79 | PD1 — GPIO PD1 / OSC_OUT |
| Pin 80 | PD2 — GPIO PD2 / TIM3_ETR / UART5_RX |
| Pin 81 | PD3 — GPIO PD3 / USART2_CTS |
| Pin 82 | PD4 — GPIO PD4 / USART2_RTS |
| Pin 83 | PD5 — GPIO PD5 / USART2_TX |
| Pin 84 | PD6 — GPIO PD6 / USART2_RX |
| Pin 85 | PD7 — GPIO PD7 / USART2_CK |
| Pin 86 | PB3 — GPIO PB3 / JTDO / SPI3_SCK / TIM2_CH2 |
| Pin 87 | PB4 — GPIO PB4 / NJTRST / SPI3_MISO / TIM3_CH1 |
| Pin 88 | PB5 — GPIO PB5 / I2C1_SMBAI / SPI3_MOSI / TIM3_CH2 |
| Pin 89 | PB6 — GPIO PB6 / I2C1_SCL / TIM4_CH1 |
| Pin 90 | PB7 — GPIO PB7 / I2C1_SDA / TIM4_CH2 |
| Pin 91 | BOOT0 — Boot mode select |
| Pin 92 | PB8 — GPIO PB8 / TIM4_CH3 |
| Pin 93 | PB9 — GPIO PB9 / TIM4_CH4 |
| Pin 94 | PE0 — GPIO PE0 / TIM4_ETR |
| Pin 95 | PE1 — GPIO PE1 |
| Pin 96 | VSS_5 — Ground |
| Pin 97 | VDD_5 — Digital supply 2.0-3.6 V |
| Pin 98 | PE2 — GPIO PE2 (alternate location, trace clock) |
| Pin 99 | PE3 — GPIO PE3 (alternate location) |
| Pin 100 | VSS_6 — Ground |
Typische Anwendungen
STM32F105VCT6 ist geeignet für 6 Anwendungs: Industrial Gateway with USB OTG + Dual CAN, USB HID / CDC / Mass-Storage Host Device, CAN-Based Motor Control / Sensor Node, Point-of-Sale / Kiosk Terminal, LCD HMI Panel Using FSMC, IoT Edge Sensor with USB Diagnostics Port.
Industrial Gateway with USB OTG + Dual CAN
The STM32F105VCT6's USB OTG Full-Speed host, dual CAN 2.0B active, and 5 USARTs in a single LQFP-100 package make it an ideal industrial gateway controller. The Cortex-M3 at 72 MHz with hardware divider can sustain CAN throughput of 1 Mbit/s per channel while also running USB CDC/ECM host stacks, making the part a natural fit for USB-to-CAN bridges, RS485-to-USB converters, and protocol gateway boards. The 256 KB Flash hosts a USB host stack plus a CANopen or Modbus library, leaving headroom for application code. Compared to using an F103, the F105 saves the BOM cost of an external USB controller and a second CAN transceiver MCU.
Empfohlen
USB HID / CDC / Mass-Storage Host Device
The integrated USB 2.0 Full-Speed OTG controller with on-chip PHY makes the STM32F105VCT6 a strong choice for USB host and device peripherals such as USB keyboards, barcode scanners, USB-to-serial adapters, USB mass-storage bootloaders, and CDC-ACM bridges. The 72 MHz Cortex-M3 can sustain USB Full-Speed (12 Mbps) enumeration and bulk transfers without CPU bottlenecking, while the 256 KB Flash holds USB host class drivers plus application firmware. Designers pick the F478-variant F407 for higher-speed applications, but the F105VOTOTOTOSP6 hits the right cost point for HID and CDC class devices.
Empfohlen
CAN-Based Motor Control / Sensor Node
With two independent CAN 2.0B controllers, six timers (one 16-bit advanced-control, two 16-bit general-purpose, plus basic and SysTick), the STM32F105VCT6 can serve as a CAN node that drives a brushed or stepper motor while reporting telemetry over the second CAN bus. The advanced-control timer supports center-aligned PWM with dead-time insertion for half-bridge motor drives, and the 32-bit Cortex-M3 handles PID control loops and CANopen DS402 profiles. The 80+ GPIO exposed by the LQFP-100 enable driving multiple motors or sensor arrays from a single chip.
Empfohlen
Point-of-Sale / Kiosk Terminal
POS terminals and self-service kiosks need USB host for barcode readers and printers, Ethernet for cloud sync, and reliable real-time control for displays and keypads. The STM32F105VCT6 combines USB OTG host, 10/100 Ethernet MAC, FSMC for LCD expansion, and the Cortex-M3 72 MHz core - giving a single MCU all the interfaces a low-to-mid-volume POS terminal needs. The 256 KB Flash holds application firmware plus network protocol stacks, and 64 KB SRAM is sufficient for display buffer and TCP socket management when paired with a low-cost Ethernet PHY such as the LAN8720.
Empfohlen
LCD HMI Panel Using FSMC
Although the STM32F105VCT6 lacks FSMC in some lineups, its LQFP-100 variant exposes parallel GPIO plus SPI/I2S interfaces that drive small TFT LCDs up to 320x240 directly. For larger 800x480 HMI panels requiring an external bus, the F105VCT6 can drive them through SPI with DMA, freeing CPU cycles for touch handling and UI logic. Designers pick the F105 for cost-sensitive HMI nodes; the F407 is the upgrade path for higher-resolution displays needing FSMC bandwidth.
Empfohlen
IoT Edge Sensor with USB Diagnostics Port
Industrial IoT edge nodes often need a USB diagnostic port alongside Ethernet and CAN interfaces. The STM32F105VCT6 provides USB OTG device mode for diagnostics, an Ethernet MAC for cloud uplink, and dual CAN for sensor bus access, in a single 256 KB Flash MCU. The 64 KB SRAM handles MQTT-style buffering and CAN frame queues, while the RTC with VBAT domain allows battery-backed timestamping for sensor data. This is the typical connectivity-line use case the STM32F105 was designed for.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für STM32F105VCT6 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | STM32F105RCT6 | STM32F107VCT6 | STM32F103VCT6 | GD32F105VCT6 | STM32F105VCT7 | STM32F105VBT6 |
|---|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | GigaDevice | STMicroelectronics | STMicroelectronics |
| Package | LQFP-100 | LQFP-64 | LQFP-100 - same | LQFP-100 - same | LQFP-100 - same | LQFP-100 - same | LQFP-100 - same |
| Core | Cortex-M3 72 MHz | Cortex-M3 72 MHz | Cortex-M3 72 MHz | Cortex-M3 72 MHz | Cortex-M3 108 MHz | Cortex-M3 72 MHz | Cortex-M3 72 MHz |
| Flash | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 128 KB |
| SRAM | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| USB OTG | Yes (Host + Device) | Yes (Host + Device) | Yes (Host + Device) | Device only (no OTG host) | Yes (Host + Device) | Yes (Host + Device) | Yes (Host + Device) |
| CAN 2.0B | 2x bxCAN | 2x bxCAN | 2x bxCAN | 1x bxCAN | 2x bxCAN | 2x bxCAN | 2x bxCAN |
| Ethernet MAC | Yes (MII/RMII) | Yes (MII/RMII) | Yes (MII/RMII) | No | Yes (MII/RMII) | Yes (MII/RMII) | Yes (MII/RMII) |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +105C | -40C to +85C |
Wichtigste Unterscheidungsmerkmale
- True USB OTG host + dual CAN + Ethernet MAC on a single Cortex-M3 (vs. STM32F103VCT6)
- Pin-compatible Cortex-M3 with higher 108 MHz clock for faster response (vs. GD32F105VCT6)
- Drop-in upgrade with extended industrial temperature range (vs. STM32F105VCT7)
Designhinweise
Estimated: at 72 MHz run mode, the STM32F105VCT6 consumes approximately 30 mA on VDD with peripherals active. Use a 100 nF decoupling cap on each VDD/VSS pin pair and a 4.7 uF bulk cap near the VDDA pin. Place VBAT through a 0.1 uF cap and a Schottky diode when sharing with the main 3.3 V rail to allow RTC retention when VDD drops.
Route the HSE 8 MHz crystal traces as short as possible and guard them with a ground ring to minimize EMI. The USB DP/DM pair (PA11/PA12) requires 90-ohm differential routing and a 1.5 kohm pull-up on DP for full-speed device mode - place these resistors as close to the MCU as practical. For Ethernet RMII, the 50 MHz reference clock trace to the external PHY must be length-matched to within 50 mils to keep skew under 4 ns.
Do not enable both the JTAG and SWD pins (PA13/14/PB3/PB4) without considering firmware remapping, since the F105VCT6 default state uses PA13/PA14 for SWD and remaps PB3/PB4 to JTAG trace pins. Designers using TIM2_CH1 on PA15 must also remember PA15 is the JTDI pin, which requires disabling JTAG to use as a normal GPIO. Validate alternate-function mapping with STM32CubeMX before committing to a pinout.
The LQFP-100 package has a theta_JA around 65 C/W on a standard 2-layer JEDEC test board. Estimated: at full 72 MHz load with all peripherals enabled, the chip typically dissipates around 100 mW, producing a 6-7 C junction rise. Industrial designs at 85 C ambient are well within the 105 C Tj max, but enclosed industrial enclosures may push ambient above 70 C - verify thermal margin with a real prototype.
Compliance-Informationen
RoHS and REACH compliant per ST product documentation. Industrial grade - not AEC-Q100 qualified; choose STM32F105VCT7 automotive grade or ST's dedicated automotive parts for vehicle applications. Halogen-free status not explicitly stated in the verified web data.
Ähnliche Suchanfragen
Verwandte Bauteile & Begriffe
Empfehlungen werden geladen...