Microchip Technology

SY88083LMG - 12.5Gbps Limiting Post Amplifier | Microchip

Teilenummer: SY88083LMG ✓ Aktiv
Programmable Vdss 16-QFN, 3 mm x 3 mm Package
MOQ: 1 |

SY88083LMG Übersicht

The Microchip Technology SY88083LMG is a limiting postamplifier integrated circuit for continuous-mode, multi-rate fiber-optic receivers operating from 1 Gbps to 12.5 Gbps. The device provides a high-bandwidth, high-sensitivity input stage, programmable wide-range signal-detect and loss-of-signal assertion thresholds, approximately 4 dB of electrical hysteresis, and selectable open-collector or TTL-compatible status outputs. It is packaged in a 16-QFN package measuring 3 mm by 3 mm.

A limiting postamplifier is a decision-threshold amplifier used at the output of an optical receiver. It converts a high-speed current-mode signal from a photodiode or transimpedance amplifier into a clean, logic-compatible digital output. By placing a programmable decision threshold directly in the signal path, this device class separates valid data from noise and supports automatic adaptation to optical power, temperature, aging, and component-tolerance variations.

The SY88083LMG supports multi-rate system designs without changing the receiver front end. Its programmable reference voltage allows the threshold to be adjusted for system reach, while approximately 4 dB of hysteresis reduces chattering in the loss-of-signal and signal-detect indications. The status-control pin selects open-collector or TTL-compatible operation, and an external pull-up resistor of 5 kΩ to 10 kΩ is recommended for open-collector status outputs.

The device also provides input-fault detection and digital interface control, making it suitable for continuous monitoring of optical receivers, PON equipment, data-center links, and industrial optical transceivers. Its limiting architecture produces a digital decision rather than serving as a linear analog gain stage.

The 3 mm by 3 mm 16-QFN package minimizes board area, but high-speed routing and short return paths are essential. Place the device close to the receive-side signal chain, provide a low-inductance ground connection, and observe the manufacturer’s differential impedance and decoupling recommendations. Keep the status pull-ups electrically quiet so switching activity does not couple into the sensitive input stage.

This page consolidates the manufacturer’s receiver application data, distributor availability information, device-family comparisons, and practical design guidance. It also identifies candidate same-package devices for engineering evaluation while clearly separating confirmed functions from parameters that must be confirmed against the latest manufacturer documentation before layout release.

Drop-in-Alternativen für SY88083LMG – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

SY88782LMG

✅ Drop-In
📦 QFN-16 (3 mm x 3 mm)
Same 16-QFN package and programmable threshold function; threshold range and status-output implementation differ by up to 30% and require pin-level verification

📋 Referenzalternative (nicht im Katalog)

SY88343BLMG-TR

✅ Drop-In
📦 QFN-16 (3 mm x 3 mm)
Same 16-QFN package and limiting-amplifier category; supply-voltage and power-consumption limits can differ by up to 30%, so pin and threshold functions must be checked

📋 Referenzalternative (nicht im Katalog)

SY88083LMG Grenzwerte & elektrische Eigenschaften

Device Type Limiting postamplifier
Supported Data Rate 1 Gbps to 12.5 Gbps
Signal Mode Continuous mode, multi-rate
Application Fiber-optic receiver
Gehäuse 16-QFN, 3 mm x 3 mm
Number of Channels 1 channel
Input Stage High-bandwidth, high-sensitivity
Threshold Control User-programmable, wide-range SD/LOS assertion thresholds
Referenzspannung Programmable
Electrical Hysteresis Typically 4 dB
Status Output Selectable open-collector or TTL-compatible
Status Pull-Up Resistor 5 kΩ to 10 kΩ
Input Fault Detection Supported
Digital Interface Control Supported
RoHS-Status Compliant
Montageart Surface mount
Lebenszyklusstatus Active

SY88083LMG 16-qfn, 3 mm x 3 mm Pinbelegungsleitfaden

Pinbelegung für SY88083LMG (16-qfn, 3 mm x 3 mm-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für SY88083LMG im 16-qfn, 3 mm x 3 mm-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für SY88083LMG.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

SY88083LMG ist geeignet für 6 Anwendungs: Multi-Rate Optical Receiver Front Ends, PON Optical Network Receivers, Data-Center Optical Link Receivers, Industrial Gigabit Ethernet Interfaces, Optical Transceiver Receive Channels, Optical Link Health Monitoring.

🌐

Multi-Rate Optical Receiver Front Ends

The SY88083LMG fits the decision stage of a continuous-mode fiber-optic receiver operating from 1 Gbps to 12.5 Gbps. Its high-bandwidth, high-sensitivity input stage converts the recovered analog signal into a clean digital output, while programmable signal-detect and loss-of-signal thresholds allow the system to accommodate optical-power variation. The typically 4 dB of electrical hysteresis also reduces indication chattering near the decision limit, improving receiver monitoring stability without changing the external photodiode or transimpedance front end.

🔗

PON Optical Network Receivers

The SY88083LMG is applicable to burst-mode-capable PON receiver designs that require fast decision-making and reliable link-status reporting. The programmable wide-range assertion and de-assert thresholds let the receiver tune detection to its expected optical budget, while the selectable open-collector or TTL-compatible output supports host monitoring hardware. Place the amplifier after the transimpedance amplifier and route the status pull-ups away from the sensitive receive path to limit coupling from switching events.

🖥️

Data-Center Optical Link Receivers

The SY88083LMG supports receiver decision functions for data-center links operating within its documented 1 Gbps to 12.5 Gbps range. Programmable reference control allows threshold tuning against channel loss and receiver sensitivity, while the hysteresis helps prevent noisy signals from repeatedly toggling the loss-of-signal indication. In dense server and switch designs, the compact 3 mm by 3 mm 16-QFN package saves board area, although short high-speed routing and a continuous ground reference remain essential.

🏭

Industrial Gigabit Ethernet Interfaces

The SY88083LMG can be used in industrial fiber-based Ethernet receiver subsystems where signal integrity and dependable link-status detection are required. Its wide-range programmable detection thresholds support factory-adjusted optical power windows, and the approximately 4 dB of hysteresis reduces false loss-of-signal events in electrically noisy environments. The TTL-compatible or open-collector status interface allows connection to industrial PHYs or supervisory controllers, subject to correct logic-level and pull-up configuration.

📡

Optical Transceiver Receive Channels

The SY88083LMG is suitable for the receive-channel decision stage of an optical transceiver module, where a recovered analog signal must become a high-speed digital output. The high-bandwidth input stage supports continuous multi-rate operation, and the programmable threshold lets module designers optimize sensitivity across temperature and optical-power conditions. Use the open-collector configuration with a 5 kΩ to 10 kΩ pull-up when the host interface requires that electrical behavior, and verify loss-of-signal polarity in the final schematic.

🔧

Optical Link Health Monitoring

The SY88083LMG provides integrated decision and fault-reporting functions for systems that must monitor optical link health. Its signal-detect and loss-of-signal thresholds can be programmed, and typical 4 dB of hysteresis limits output toggling when a noisy recovered signal approaches the decision point. The status-control pin supports open-collector or TTL-compatible reporting, which simplifies integration with supervisory logic, test points, and system-fault handlers in industrial and telecom-oriented receiver assemblies.

Zusammenfassung der empfohlenen Produkte

SY88782LMG Same-package limiting amplifier candidate Verwendet in: Multi-Rate Optical Receiver Front Ends, Data-Center Optical Link Receivers, Optical Transceiver Receive Channels SY88343BLMG-TR Same-package limiting amplifier candidate Verwendet in: PON Optical Network Receivers, Industrial Gigabit Ethernet Interfaces, Optical Link Health Monitoring
What is the SY88083LMG used for?
The SY88083LMG is a limiting postamplifier used in fiber-optic receivers for continuous-mode, multi-rate data links from 1 Gbps to 12.5 Gbps. According to the Microchip SY88083L datasheet, it uses a high-bandwidth, high-sensitivity input stage to generate a digital decision from the recovered analog signal. It also supports programmable signal-detect and loss-of-signal thresholds, making it suitable for optical receiver front ends in PON, data-center, and industrial communication equipment.
What are the key specifications of SY88083LMG?
The SY88083LMG supports data rates from 1 Gbps to 12.5 Gbps and comes in a 16-QFN, 3 mm by 3 mm package. The Microchip SY88083L datasheet identifies a high-bandwidth, high-sensitivity input stage, user-programmable wide-range signal-detect and loss-of-signal thresholds, typically 4 dB of electrical hysteresis, and selectable open-collector or TTL-compatible status indication. These features make it a decision-threshold amplifier rather than a conventional linear amplifier.
How does the SY88083LMG reduce LOS and SD chattering?
The SY88083LMG reduces signal-detect and loss-of-signal chattering by applying typically 4 dB of electrical hysteresis around its decision threshold. According to the Microchip SY88083L datasheet, the wide-range programmable assertion and de-assert thresholds allow system reach to be optimized, while the hysteresis prevents noisy receive signals from repeatedly crossing the threshold. This is especially useful when optical power changes near the detection limit.
Can the SY88083LMG status output use TTL levels?
Yes, the SY88083LMG provides a logic-level control pin that allows selection of an open-collector or TTL-compatible loss-of-signal and signal-detect output. The Microchip SY88083L datasheet specifies an external 5 kΩ to 10 kΩ pull-up resistor when the open-collector configuration is used. Confirm the selected logic level and pull-up arrangement against the host interface before releasing the PCB layout.
Where can I download the SY88083LMG datasheet PDF?
The SY88083LMG datasheet PDF is available from the Microchip document link listed on this page, and the manufacturer product page for SY88083L covers the same device family. The SY88083LMG ordering code identifies the 16-QFN 3 mm by 3 mm package version. Use the manufacturer document to confirm the final pin description, recommended operating conditions, and absolute maximum ratings for the exact ordering code.
Where can I find the SY88083LMG pinout?
The SY88083LMG pinout is documented in the pin-description table of the Microchip SY88083L datasheet. The device is offered in a 16-QFN package, and the package drawing identifies the terminal arrangement and exposed-pad requirements. Use the pin-description table when assigning PCB tracks, and follow the recommended land pattern rather than inferring connections from a generic QFN drawing.
What are the alternatives to SY88083LMG?
The SY88782LMG and SY88343BLMG-TR are the closest published same-package candidates for engineering review. The published comparison identifies both as Microchip QFN-16 limiting amplifiers, while the SY88782LMG provides programmable threshold control and the SY88343BLMG-TR is presented as a separate specification family. Pin-level compatibility must still be confirmed from each device’s datasheet before either part is used as a drop-in substitute.
What is the best drop-in replacement for SY88083LMG?
The SY88783LMG and SY88343BLMG-TR are the closest same-package candidates identified for evaluation, but neither can be described as a confirmed drop-in replacement without pin-level verification. Both are listed as QFN-16 Microchip limiting amplifiers, yet threshold programming, status-output logic, supply limits, and internal functions can differ. Check the functional block diagrams and pin tables before ordering a substitute.
Can SY88083LMG replace a generic limiting postamplifier?
The SY88083LMG can serve as a limiting postamplifier in a compatible fiber-optic receiver, but it is not a universal replacement for every signal-chain device. Its supported range is 1 Gbps to 12.5 Gbps, and it requires matching supply, impedance, threshold, and open-collector or TTL status-output arrangements. Verify signal polarity, data rate, logic levels, and pin mapping at the transistor level.
Is SY88083LMG suitable for 10G and 12.5G optical links?
Yes, the SY88083LMG is suitable for 10G and 12.5G optical receiver decision stages because its documented multi-rate operating range extends from 1 Gbps to 12.5 Gbps. According to the Microchip SY88083L datasheet, the limiting postamplifier supports continuous-mode multi-rate designs and includes programmable threshold control. Receiver bandwidth, loss, jitter budget, and board-level signal integrity still determine end-to-end link performance.
What is the difference between SY88083LMG and SY88782LMG?
The SY88083LMG and SY88782LMG are both Microchip QFN-16 limiting amplifiers with programmable threshold control, but they belong to different specification families. The published comparison identifies the SY88782LMG as a fast limiting amplifier for Gbps links with programmable threshold detection, while the SY88083LMG additionally emphasizes continuous-mode multi-rate operation and selectable open-collector or TTL status outputs. Compare pin functions and electrical limits before substitution.
When should I choose SY88083LMG over a same-package alternative?
Choose the SY88083LMG when the receiver requires a continuous-mode limiting stage for 1 Gbps to 12.5 Gbps operation, programmable wide-range signal-detect and loss-of-signal thresholds, and selectable open-collector or TTL-compatible status outputs. The SY88782LMG or SY88343BLMG-TR may suit different gain, supply, or programming architectures. Select the alternative only when its pinout and threshold-control behavior satisfy the complete receiver specification.
How should the SY88083LMG be placed on a PCB?
Place the SY88083LMG as close as practical to the recovered-signal source so the high-bandwidth input path remains short and controlled. Use the manufacturer’s reference layout for the 16-QFN land pattern, route the sensitive differential or current-mode path away from status outputs, and provide a low-impedance ground return. Keep pull-up routing away from the input node and follow the datasheet’s decoupling and return-path instructions.
How is the SY88083LMG supply voltage selected?
The SY88083LMG supply voltage must be selected within the exact operating and absolute-maximum limits stated for the SY88083L device in the Microchip datasheet. The available listing confirms a maximum supply voltage of 3.6 V for a related QFN-16 comparison entry, but the target device’s complete operating range must be confirmed directly from its specifications. Never derive the rail value from a related part or from the receive-side signal amplitude.
Where can I buy SY88083LMG and check current lead time?
Use the Request a Quote form on this page to request the current SY88083LMG unit price, stock position, minimum order quantity, and production lead time. The device is listed by multiple suppliers and is described as an active Microchip limiting postamplifier, but availability changes by region and order quantity. Include the 16-QFN packaging requirement and your target shipment date in the quotation request.

Technische Referenzdaten für SY88083LMG – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the SY88083LMG when a fiber-optic receiver needs a limiting decision stage covering 1 Gbps to 12.5 Gbps, programmable wide-range signal-detect and loss-of-signal thresholds, and selectable open-collector or TTL-compatible status reporting. The SY88782LMG is worth evaluating when its specific threshold architecture and pin functions match the receiver more closely. Consider the SY88343BLMG-TR only after confirming its supply range, status behavior, and pin mapping against the target design. All three candidates are listed as Microchip QFN-16 limiting-amplifier families, but package similarity alone does not guarantee electrical or functional interchangeability. For new designs, use the SY88083LMG when its documented multi-rate coverage and hysteresis behavior align with the link budget; for second sourcing, compare the complete pin and threshold-control tables rather than relying on package outline or category alone.

Vergleich mit Alternativen

Parameter Dieses Produkt SY88782LMG SY88343BLMG-TR
Brand Microchip Technology Microchip Technology Microchip Technology
Package 16-QFN, 3 mm x 3 mm 16-QFN, 3 mm x 3 mm 16-QFN, 3 mm x 3 mm
Function Limiting postamplifier Limiting amplifier Limiting amplifier

Wichtigste Unterscheidungsmerkmale

  • Explicit multi-rate receiver support (vs. SY88782LMG)
  • Programmable detection thresholds with defined hysteresis (vs. SY88343BLMG-TR)
  • Selectable status-output interface (vs. SY88782LMG)

Designhinweise

Treat the SY88083LMG input as a high-speed decision node. Place it immediately after the transimpedance amplifier, minimize stub length, maintain the manufacturer-specified differential or current-mode impedance, and provide a continuous ground reference beneath the QFN. Avoid routing the sensitive input beneath pull-up components or digital status nets. The 3 mm by 3 mm package saves area but does not compensate for long or discontinuous return paths.

Follow the Microchip reference layout for the 16-QFN land pattern, exposed pad, and thermal-via arrangement. Decouple the supply rail at the device and keep the status-control and pull-up connections physically separated from the receive-signal path. Because the part makes a threshold decision near the noise floor, small ground-bounce or supply disturbances can shift the effective decision point and produce false loss-of-signal transitions.

Do not assume that matching the 16-QFN outline guarantees a drop-in substitution. Verify pin names, signal polarity, threshold-control implementation, supply limits, status-output type, and input termination for SY88782LMG or SY88343BLMG-TR. In open-collector mode, populate the manufacturer-specified 5 kΩ to 10 kΩ pull-up and confirm the loss-of-signal polarity expected by the system controller.

Compliance-Informationen

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

RoHS status is identified in the published specification comparison. Automotive qualification, REACH status, halogen-free status, and conflict-minerals reporting were not established.

Daten verifiziert am: 2026-11-20 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

SY88083LMG datasheet SY88083LMG pinout SY88083LMG datasheet pdf SY88083LMG price SY88083LMG stock Microchip SY88083LMG SY88083L 12.5Gbps limiting amplifier SY88083LMG QFN-16 footprint SY88083LMG fiber optic receiver SY88083LMG vs SY88782LMG SY88083LMG vs SY88343BLMG-TR SY88083LMG drop-in replacement SY88083LMG programmable threshold control SY88083LMG open collector TTL output

Verwandte Bauteile & Begriffe

Microchip Technology SY88083LMG SY88083L SY88782LMG SY88343BLMG-TR limiting postamplifier decision-threshold amplifier fiber-optic receiver special purpose amplifier signal detect loss of signal programmable threshold electrical hysteresis open-collector output TTL-compatible output current-mode signal continuous mode multi-rate operation 16-QFN package QFN family surface mount 3 mm x 3 mm package input fault detection RoHS 12.5 Gbps
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen