Texas Instruments

TLV2432QD - Dual 500 kHz Rail-to-Rail Op Amp | Texas Instruments

Teilenummer: TLV2432QD ✓ Aktiv
10 V Vdss 150 pA Id 8-SOIC, 0.154 inch body width Package
MOQ: 1 |

TLV2432QD Übersicht

The Texas Instruments TLV2432QD is a dual, low-voltage operational amplifier with rail-to-rail output, wide-input-voltage operation, a 10 V maximum supply rating, and 500 kHz gain-bandwidth performance. The device is packaged in an 8-pin SOIC and is intended for signal conditioning, buffering, current sensing, analog measurement, filtering, and precision control applications.

Operational amplifiers are analog signal-processing ICs that amplify the difference between two input voltages while providing high input impedance and low output impedance. The TLV2432 belongs to the LinCMOS operational-amplifier family, combining CMOS-style low-power characteristics with rail-to-rail output capability. Rail-to-rail output allows the output voltage to approach both supply rails under suitable load and output-voltage conditions, making the device useful in low-voltage systems where signal headroom is limited.

The TLV2432 uses an extended common-mode input-voltage range and supports operation from a single 5 V supply or from supplies up to ±5 V, as described in the manufacturer product information. Its nominal gain-bandwidth product is 500 kHz, and its slew rate is 0.25 V/us according to the distributor specification listing. The amplifier also provides low input-bias current, listed as approximately 150 pA, which is useful when the source impedance is high and input bias errors must be minimized.

The TLV2432QD is the Q-grade version of the TLV2432 family and is identified by the manufacturer as an 8-SOIC, rail-to-rail dual operational amplifier. The Q suffix indicates the specified grade and packaging ordering code, while the device family includes related TLV2432 variants with different packaging or temperature options. Its wide-input-voltage and rail-to-rail-output characteristics make it suitable for sensor interfaces, transducer amplifiers, active filters, low-voltage instrumentation, and general-purpose analog signal chains.

Typical circuit use places each amplifier in an inverting or non-inverting configuration with external feedback resistors and decoupling capacitors close to the supply pins. When using the device for precision measurements, input bias current, input-offset voltage, common-mode range, output swing, and stability with the selected feedback network should be evaluated together. The 500 kHz bandwidth is adequate for many low-to-moderate-frequency signal-conditioning tasks but does not make the part suitable for demanding high-speed video or RF applications.

The principal design tradeoff is the relationship between low-power analog flexibility and bandwidth. TLV2432 is appropriate when rail-to-rail output, wide input range, low bias current, and a moderate 500 kHz bandwidth are more important than very high slew rate or multi-gigahertz signal bandwidth. Confirm the exact ordering code, temperature range, and mechanical drawing against the manufacturer datasheet before releasing a production PCB.

Drop-in-Alternativen für TLV2432QD – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit TLV2432QD (gleiche Bauform und Footprint) – abweichend in Package, Gain-Bandwidth Product, Amplifier Type, Number of Channels, Slew Rate.

Texas Instruments
Package: 8-pin SOIC (D)
Gain-Bandwidth Product: 1 MHz
Amplifier Type: Precision Operational Amplifier
Vergleichen mit TLV2432QD →
Texas Instruments
Package: 8-SOIC, 3.90 mm width
Amplifier Type: Dual operational amplifier
Number of Channels: 2 channels
Vergleichen mit TLV2432QD →

TLV2432ID

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 8-SOIC
Same TLV2432 dual-amplifier family and 8-SOIC footprint; ordering suffix and temperature grade differ by up to 30% in grade designation

📋 Referenzalternative (nicht im Katalog)

TLV2432IP

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 8-SOIC
Same TLV2432 family and 8-SOIC footprint; ordering suffix differs, with no quantified change to the core 500 kHz bandwidth rating

📋 Referenzalternative (nicht im Katalog)

TLV2432AID

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 8-SOIC
Same-family enhanced variant in 8-SOIC; A-version specifications may differ by up to 20% from the original TLV2432 ratings

📋 Referenzalternative (nicht im Katalog)

TLV2432CD

✅ Drop-In
Texas Instruments
📦 8-SOIC
Dual operational amplifier · CMOS · 2 channels · 10 V · 500 kHz · Rail-to-rail output · 8-SOIC, 3.90 mm width · 8 pins

Preis auf Anfrage

Datenblatt ansehen →

OPA2277UA

✅ Drop-In ⚠️ Spezifikationen ungeprüft
Texas Instruments
📦 8-SOIC
2 (Dual) · Precision Operational Amplifier · 10 µV · ±0.1 µV/°C · 134 dB · 140 dB · 130 dB · 800 µA

Preis auf Anfrage

Datenblatt ansehen →

TLV2432QD Grenzwerte & elektrische Eigenschaften

Number of Amplifiers 2
Product Type Dual operational amplifier
Maximum Supply Voltage 10 V
Supply Configuration Single or dual supply
Gain-Bandwidth Product 500 kHz
Slew Rate 0.25 V/us
Input Bias Current 150 pA
Ausgangstyp Rail-to-rail output
Common-Mode Input Range Extended common-mode input voltage range
Operating Supply Condition 4.5 V minimum with 5 V single supply
Anzahl der Pins 8
Gehäuse 8-SOIC, 0.154 inch body width
Montageart Surface mount
Process Technology Advanced LinCMOS
Output Swing Includes both supply rails
Application Areas Signal conditioning, buffering, current sensing, analog measurement, filtering, and precision control

TLV2432QD 8-soic, 0.154 inch body width Pinbelegungsleitfaden

Pinbelegung für TLV2432QD (8-soic, 0.154 inch body width-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für TLV2432QD im 8-soic, 0.154 inch body width-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für TLV2432QD.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

TLV2432QD ist geeignet für 6 Anwendungs: Low-Voltage Sensor Signal Conditioning, Shunt-Based Current Measurement, Active Filtering and Signal Conditioning, Precision Control and Buffering, Industrial and Instrumentation Interfaces, Portable and Battery-Powered Analog Circuits.

🧩

Low-Voltage Sensor Signal Conditioning

The TLV2432QD is suitable for conditioning sensor outputs where the signal must be amplified without requiring a large output swing beyond the supply rails. Its 500 kHz gain-bandwidth product supports moderate-bandwidth measurement channels, while the approximately 150 pA input-bias current limits bias-current error in high-impedance sensor interfaces. The extended common-mode input range is valuable when a sensor output lies near either side of the midpoint of a low-voltage supply. Each amplifier can form a non-inverting or inverting stage, and external resistors should be selected to balance resistor noise, accuracy, and the closed-loop bandwidth required by the measurement system.

⚡

Shunt-Based Current Measurement

A shunt current monitor can use one TLV2432QD channel to amplify the small differential voltage produced across a sense resistor, with the second channel available for input offset, reference, or additional signal conditioning. The low 150 pA input-bias current helps maintain accuracy when the effective source impedance is high, and the dual-amplifier configuration reduces the number of separate analog ICs required. The 500 kHz bandwidth accommodates many slowly changing current measurements without introducing the noise of a much faster amplifier. Use a Kelvin-connected shunt, verify the amplifier input common-mode range at maximum current, and select feedback resistors that maintain stable closed-loop operation.

📡

Active Filtering and Signal Conditioning

The TLV2432QD can implement first- and second-order active filters when the desired corner frequencies remain well below its 500 kHz gain-bandwidth product. Rail-to-rail output improves usable filter swing in low-voltage systems, allowing more of the output range to remain available to the next stage. The approximately 150 pA input-bias current is helpful when the filter includes high-value resistors, although excessive resistance can increase thermal noise and reduce practical bandwidth. Select capacitor tolerances according to the required corner-frequency accuracy, check the feedback network against the manufacturer's stability guidance, and include supply bypass capacitors close to the device for predictable analog behavior.

🏭

Precision Control and Buffering

The TLV2432QD can buffer a control reference or drive a limited-load analog stage when the system operates from low-voltage rails. Rail-to-rail output helps preserve signal range, and the dual-amplifier arrangement allows one channel to perform control amplification while the other buffers a feedback or monitoring node. The device's 0.25 V/us slew rate should be checked against the required signal edge rate because a wide output swing at a high frequency can become slew-limited. Keep the load within the output-current capability, maintain adequate phase margin with the chosen gain, and place both bypass capacitors near the supply pins.

🏭

Industrial and Instrumentation Interfaces

TLV2432QD is applicable to industrial instrumentation that accepts low-level analog signals and requires rail-to-rail output stages. The 10 V maximum supply rating, dual amplifier count, and 8-SOIC package simplify design partitioning around a 5 V analog rail. The extended common-mode input range can reduce front-end constraints in systems with narrow supply voltages, while the 500 kHz bandwidth is appropriate for many process-control and diagnostic signals rather than high-speed data acquisition. Engineers should confirm operating-temperature grade requirements, verify the supply rail during startup, and use grounded or properly referenced analog layout to minimize noise pickup.

📱

Portable and Battery-Powered Analog Circuits

The low-power CMOS operating-amplifier architecture makes the TLV2432QD relevant to portable equipment operating from a limited supply. Rail-to-rail output can improve utilization of a low-voltage battery-derived rail, while the dual configuration supports two buffered channels or one measurement channel plus one control channel. The family's low input-bias current is advantageous when working from high-impedance sensors or resistive dividers. Power budget calculations should include both the load current and the amplifier's own quiescent current, and the output should be checked for capacitive-load stability when driving long PCB traces or connector inputs.

What is the Texas Instruments TLV2432QD?
The Texas Instruments TLV2432QD is a dual, low-voltage CMOS operational amplifier with rail-to-rail output, extended common-mode input range, and a 500 kHz gain-bandwidth product. It is supplied in an 8-pin SOIC package and is specified for signal-conditioning, buffering, filtering, current-sensing, and analog-measurement circuits. According to the Texas Instruments TLV2432 product page, the family is a dual operational amplifier rated for operation with supplies up to 10 V.
What are the key specifications of TLV2432QD that engineers should know?
TLV2432QD provides two amplifiers, a 500 kHz gain-bandwidth product, 0.25 V/us slew rate, approximately 150 pA input-bias current, rail-to-rail output, and a maximum supply rating of 10 V. The device uses an 8-SOIC package and can operate from a 4.5 V minimum single supply, including a 5 V single-supply arrangement. These characteristics place it between general-purpose low-power amplifiers and higher-speed precision signal-conditioning parts.
Where can I download the TLV2432QD datasheet PDF?
The official Texas Instruments TLV2432 product page is the preferred starting point for the TLV2432QD datasheet, ordering information, and related technical documents. It identifies the family as a dual 10 V, 500 kHz operational amplifier. Use the manufacturer datasheet to confirm the Q-grade ordering information, pin assignments, electrical limits, test conditions, and the mechanical drawing before finalizing a board layout.
Where can I find the TLV2432QD pinout?
The TLV2432QD pinout is defined in the Texas Instruments TLV2432 family documentation because the Q suffix denotes the ordering grade and package code. The distributor listing identifies the device as an 8-SOIC. Use the pin-description table and package drawing in the manufacturer datasheet when assigning each amplifier's supply, ground, input, and output connections to PCB tracks.
Is TLV2432QD rail-to-rail?
Yes, the TLV2432QD has rail-to-rail output, so its output can swing close to both supply rails under suitable loading and output-voltage conditions. The family also provides an extended common-mode input-voltage range, allowing the input stage to operate over a wider portion of the supply voltage than a conventional CMOS amplifier. Texas Instruments identifies the device as an advanced LinCMOS rail-to-rail-output wide-input-voltage operational amplifier.
What supply voltage can TLV2432QD operate from?
TLV2432QD supports a maximum total supply voltage of 10 V and is described for single-supply operation beginning at 4.5 V with a 5 V supply. It can also be used with dual supplies up to ±5 V, matching the manufacturer's 10 V maximum rating. The exact input common-mode and output-swing limits must remain valid at the selected supply voltage and load.
What is the gain-bandwidth product of TLV2432QD?
The TLV2432QD has a 500 kHz gain-bandwidth product, as stated on the Texas Instruments product page and in distributor specifications. This bandwidth determines its useful closed-loop response at different noise-gain settings. A 500 kHz device is well suited to audio-adjacent instrumentation, sensor interfaces, filtering, and general analog conditioning, but it is not intended for high-speed video, RF, or other wideband waveform applications.
Is TLV2432QD suitable for current sensing?
Yes, TLV2432QD is specifically identified for current-sensing and signal-conditioning applications. Its approximately 150 pA input-bias current helps preserve accuracy with high-impedance sensing networks, while the dual configuration allows one amplifier to amplify a shunt signal and the other to perform a second measurement or buffering function. The shunt amplifier still requires careful attention to input offset, common-mode limits, and Kelvin routing.
What is the difference between TLV2432QD and TLV2432CD?
TLV2432QD is the Q-grade 8-SOIC ordering variant, while TLV2432CD uses a different ordering suffix associated with a different grade and packaging configuration. Both belong to the same TLV2432 dual operational-amplifier family, but production substitution must account for the complete ordering code, temperature grade, reel or tube format, and manufacturer qualification status. The available comparison information does not establish a cross-grade drop-in relationship by itself.
What is the best drop-in replacement for TLV2432QD?
The TLV2432 family variants that retain the 8-SOIC footprint and matching electrical function are the closest same-brand replacement candidates, including TLV2432ID, TLV2432IP, and TLV2432AID. Their suitability depends on the required temperature grade, supply range, rail-to-rail behavior, and exact pin configuration. No manufacturer cross-reference entry in the retrieved information confirms a universal drop-in replacement, so the complete ordering code should be checked before substitution.
What can replace TLV2432QD on the same PCB?
A replacement for TLV2432QD should be a dual operational amplifier in the same 8-SOIC footprint with compatible input, output, supply, and ground assignments and operating limits that match the design. TLV2432ID, TLV2432IP, and TLV2432AID are same-family candidates, while OPA2277UA and TLV2432AID may serve broader function-equivalent designs after pinout and electrical checks. The retrieved cross-reference results do not establish every candidate as a guaranteed drop-in replacement.
When should I choose TLV2432QD over a higher-bandwidth amplifier?
Choose TLV2432QD when the design needs rail-to-rail output, an extended common-mode input range, low input-bias current, and a 500 kHz bandwidth without requiring high-speed slew performance. It is appropriate for precision sensor interfaces, current measurement, buffering, and filtering. Select a higher-bandwidth amplifier when signal edges, phase margin at high closed-loop gain, or wideband dynamic performance require more than the TLV2432 family's 500 kHz capability.
TLV2432QD vs OPA2277UA - which is better for low-voltage instrumentation?
TLV2432QD is the better match when rail-to-rail output and a 500 kHz bandwidth are central requirements, while OPA2277UA should be evaluated when precision and very low offset are more important than output swing. The retrieved information does not provide a complete side-by-side electrical comparison, so the correct choice depends on input common-mode range, offset voltage, supply range, bias current, noise, and required package pinout. Verify both against the actual measurement circuit.
Where can I buy TLV2432QD and what is its current lead time?
Use the Request a Quote form on this page to request TLV2432QD availability, current lead time, and order quantities. The manufacturer product page remains the authoritative source for lifecycle and ordering information. Commercial terms and stock status can change quickly, so obtain a written quotation for the exact 8-SOIC ordering code rather than relying on an archived unit price.
What is the price of TLV2432QD?
The current commercial price for TLV2432QD should be requested through the Request a Quote form on this page. The structured pricing area accounts for the exact ordering code, requested quantity, and current channel conditions. Do not rely on the historical unit-price reference for budgeting because distributor pricing, stock, and lifecycle conditions can change independently of the component's electrical characteristics.
Is TLV2432QD in stock and what is the lead time?
Stock and lead time for TLV2432QD should be confirmed through the Request a Quote form on this page. One archived distributor listing showed inventory at the time it was captured, but that status does not establish current availability. Provide the required quantity, tube or reel preference, and target delivery date so the order can be scheduled against current manufacturing and distribution capacity.
Does TLV2432QD comply with RoHS and automotive qualification requirements?
The electrical and ordering information for TLV2432QD is clear, but the retrieved manufacturer and distributor listings do not explicitly state RoHS, REACH, or AEC-Q100 status. Consequently, those compliance fields remain unknown rather than being assumed. Request the current material declaration, quality documentation, and automotive qualification records from Texas Instruments for the exact orderable part before using the device in a regulated or automotive design.

Technische Referenzdaten für TLV2432QD – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose TLV2432QD for low-voltage dual-channel signal conditioning when rail-to-rail output, an extended common-mode input range, approximately 150 pA input-bias current, and a 500 kHz gain-bandwidth product are important. It is particularly suitable for current measurement, sensor interfaces, filtering, buffering, and precision-control circuits running from a 5 V rail. TLV2432ID, TLV2432IP, and TLV2432CD are same-family alternatives when the ordering suffix, temperature grade, and packaging format match the design requirements. TLV2432AID offers an enhanced-family option, but its electrical limits should be checked before substitution. OPA2277UA may suit precision applications requiring one amplifier and lower offset, but it does not provide the same dual-channel package population. None should be approved as a drop-in replacement without confirming the pin assignments, supply range, common-mode limits, output swing, stability, temperature grade, and mechanical drawing.

Vergleich mit Alternativen

Parameter Dieses Produkt TLV2432ID TLV2432IP TLV2432AID TLV2432CD OPA2277UA
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same
Amplifier Count 2 2 2 2 2 1

Wichtigste Unterscheidungsmerkmale

  • Combines two amplifiers with rail-to-rail output in one package (vs. OPA2277UA)
  • Matches the original family's core bandwidth and supply rating (vs. TLV2432CD)
  • Provides low input-bias current for impedance-sensitive interfaces (vs. TLV2432AID)

Designhinweise

Do not treat the Q suffix as an electrical-performance option by itself. TLV2432QD combines the TLV2432 dual-amplifier family with an 8-SOIC ordering code. Confirm the exact suffix-to-temperature-range mapping, tube or reel format, and marking scheme against the Texas Instruments ordering information. When substituting another suffix, also compare input offset, input bias current, common-mode range, output swing, supply limits, and electrical test conditions rather than relying on the package name alone.

Place the supply bypass capacitors directly between each supply pin and ground, with the ground connection following the datasheet's recommended layout. Keep the two input and output routing paths short, particularly when the amplifier drives an ADC input or a high-impedance sensor. Use a continuous analog ground reference where appropriate and route high-current return currents away from the amplifier and its feedback components to reduce ground-induced error in precision measurements.

The 500 kHz gain-bandwidth product and 0.25 V/us slew rate must be checked against the intended closed-loop gain and signal amplitude. A large output transition can become slew-limited even when the operating frequency is below 500 kHz. For higher closed-loop gains, use the manufacturer's stability guidance, avoid excessively high feedback resistors when noise is critical, and verify capacitive loading before connecting the output to a long trace, connector, or ADC sampling network.

Estimated: amplifier dissipation is PD = (VIN - VOUT) × IOUT plus internal losses. For example, a 5 V supply producing 3.3 V at 10 mA gives an estimated external power loss of 17 mW. Add the amplifier quiescent current and account for copper area, ambient temperature, and the package thermal resistance when checking junction temperature. Confirm that the selected 8-SOIC variant's temperature rating covers the maximum ambient and expected supply tolerance.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The retrieved manufacturer and distributor information does not explicitly state environmental or automotive compliance for the exact TLV2432QD ordering code. Obtain current manufacturer quality and material documentation before production release.

Ähnliche Suchanfragen

TLV2432QD datasheet TLV2432QD pinout TLV2432QD datasheet pdf TLV2432QD specifications TLV2432QD equivalent TLV2432QD replacement TLV2432QD cross reference TLV2432QD price TLV2432QD stock Texas Instruments TLV2432QD TLV2432QD 8-SOIC footprint TLV2432QD current sensing TLV2432QD vs TLV2432CD TLV2432QD vs OPA2277UA

Verwandte Bauteile & Begriffe

Texas Instruments TLV2432QD TLV2432ID TLV2432IP TLV2432AID TLV2432CD OPA2277UA dual operational amplifier operational amplifier analog signal-processing IC LinCMOS Advanced LinCMOS rail-to-rail output extended common-mode input-voltage range gain-bandwidth product slew rate input bias current 8-SOIC SOIC family surface-mount package current sensing signal conditioning active filtering precision control industrial instrumentation
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen