Circuitos integrados

PIC16C64AT-10I/PQ

PIC16C64AT-10I/PQ - 8-Bit PIC MCU 3.5KB OTP 33 I/O | Microchip

The Microchip Technology PIC16C64AT-10I/PQ is an 8-bit RISC CMOS microcontroller in the PIC16C6X family, offering 3.5KB of One-Time-Programmable (OTP) program memory, 128 bytes of RAM, and 33 digital I/O pins in a 44-pin MQFP (PQ) surface-mount package. It operates up to 10 MHz from a 5 V supply and is rated for the industrial -40C to +85C temperature range. What is a PIC16C64A? The PIC16C64A belongs to the PIC16C6X mid-range family of 8-bit microcontrollers, descended from the original PIC16C5X baseline. These MCUs use a RISC (Reduced Instruction Set Computer) architecture with only 35 single-word instructions to learn, where most instructions execute in one instruction cycle. As a Harvard-architecture device, the PIC16C64A has separate program and data buses, allowing simultaneous instruction fetch and data access. It sits in the microcontroller hierarchy as: microcontroller -> embedded controller -> 8-bit MCU -> PIC mid-range -> PIC16C6X family. Key features of the PIC16C64AT-10I/PQ include a 10 MHz maximum clock, 200 ns instruction cycle, three hardware timers (Timer0, Timer1, Timer2), a USART module for asynchronous serial communication, and a parallel slave port. The T suffix denotes tape-and-reel packaging, while I specifies the industrial temperature grade. The PQ suffix indicates the 44-pin Metric Quad Flat Pack (MQFP) gull-wing surface-mount package. This device uses EPROM/OTP program memory rather than Flash, meaning code is written once and cannot be electrically erased. This makes the part well suited for high-volume production where firmware is finalized, but limits prototyping use compared to Flash-based PIC16F equivalents. CMOS technology provides low power consumption with typical applications drawing only a few milliamps. Typical applications include industrial control systems, motor drive front-ends, sensor interfacing, automotive body electronics, and embedded control panels where a 5 V-tolerant interface to external peripherals is required. The 33 I/O pins comfortably drive keypads, LED arrays, LCD modules, and small relay or solenoid loads. When designing with this part, note that OTP memory precludes in-system firmware updates. For development, engineers should prototype on a Flash-equipped sibling (PIC16F64A-equivalent or PIC18 baseline) and migrate to the OTP PIC16C64A once firmware is frozen. This page synthesizes distributor pricing, datasheet specifications, and drop-in alternatives from the same PIC16C6X family, providing practical context not duplicated on manufacturer product pages.

Cotización Contacto

PIC16C64AT-20/L

PIC16C64AT-20/L - 8-Bit 20MHz OTP MCU, 3.5KB | Microchip

The Microchip Technology PIC16C64AT-20/L is an 8-bit RISC microcontroller from the PIC® 16C family, featuring a 20 MHz maximum clock, 3.5 KB (2K x 14) of One-Time Programmable (OTP) program memory and 128 bytes of RAM, housed in a 44-pin PLCC (J-Lead) package with a 16.59 mm x 16.59 mm body. The “T” suffix denotes tape-and-reel packaging and the “-20” suffix indicates a 20 MHz maximum operating frequency. What is a PIC16C OTP microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral interfaces. The PIC16C family uses a Harvard-architecture RISC core that executes most instructions in a single clock cycle, making it well suited to real-time control. The “C” suffix denotes CMOS EPROM/OTP program memory - non-volatile, but write-once. Within the broader taxonomy, the PIC16C64A sits in this hierarchy: 8-bit MCU -> PIC16 family -> PIC16C6x sub-family -> PIC16C16C64A device -> OTP CMOS implementation. Key features of the PIC16C64A include 33 I/O pins, three timer modules, a Capture/Compare/PWM (CCP) module, an 8-bit parallel slave port, and serial interfaces (SSP) that support both SPI and I²C. The device integrates power-on reset (POR), brown-out detect/reset (BOR), a watchdog timer (WDT) with its own on-chip RC oscillator, and a programmable code-protection fuse. Operating voltage spans 3.0 V to 5.5 V across the commercial 0 °C to +70 °C range, with industrial -40 °C to +85 °C variants available under different temperature suffixes. Architecturally, the PIC16C64A uses a 14-bit instruction word and an 8-bit data path, allowing compact code density while keeping peripherals register-mapped. The 8-level hardware stack and 35-instruction set simplify assembly or C programming, and the CCP module provides PWM outputs for motor or LED control. The parallel slave port lets the device interface directly to an external 8-bit host bus, while the SSP peripheral supports both SPI and I²C master/slave modes. Typical applications include industrial control panels, motor drive front-ends, embedded sensor hubs, and legacy upgrade / EOL replacement designs where a proven PIC16C6x footprint and toolchain are required. The PIC16C64AT-20/L is also widely used in educational and prototyping environments that target the PIC16C instruction set. When designing with this part, verify that OTP programming is appropriate for the production volume - flashed (F-series) PIC16F variants are typically lower cost per unit and re-programmable. Confirm the 5V supply rail tolerance for analog peripherals and ensure the parallel slave port pin direction registers are correctly initialised in firmware. This page synthesises distributor pricing, verified drop-in alternatives from the PIC16C6x family, and practical design notes that go beyond what the manufacturer datasheet alone provides.

Cotización Contacto

PIC16C64AT-20/PQ

PIC16C64AT-20/PQ - 8-Bit 20MHz OTP MCU 3.5KB | Microchip

The Microchip Technology PIC16C64AT-20/PQ is an 8-bit CMOS RISC microcontroller belonging to the PIC16C family, operating at up to 20 MHz clock speed and housed in a 44-pin MQFP (10x10 mm) surface-mount package with gull-wing leads. The device integrates 3.5 KB (2K x 14) of one-time programmable (OTP) program memory and 128 bytes of RAM, with 33 digital I/O pins and a 5V nominal supply. According to the PIC16C6X family datasheet, this part is well suited for embedded control applications requiring deterministic execution and a small instruction set. An 8-bit microcontroller (MCU) is a single-chip processor that integrates CPU core, program memory, working RAM, and peripheral interfaces on one die. PIC microcontrollers use a Harvard RISC architecture that decouples program and data buses, executes one instruction per clock cycle (except branches), and supports only 35 single-word instructions. Within the broader taxonomy, the PIC16C64A sits between 8-bit MCUs and the wider PIC16 mid-range family, which itself belongs to the microcontroller hierarchy of the semiconductor category. Key features of the PIC16C64AT-20/PQ include a 200 ns instruction cycle at 20 MHz, two 8-bit and one 16-bit timer/counter, a synchronous serial port (SSP) supporting SPI and I2C, a parallel slave port, and a USART. The 33 I/O pins can drive source/sink currents up to 25 mA per pin, simplifying direct interface to relays, LEDs, and bipolar transistors. The OTP program memory allows low-cost prototyping with stable firmware retention, while the 14-bit instruction word supports immediate and literal operations. Architecturally, the PIC16C64A uses a 14-bit program word and an 8-bit data path, with an 8-level hardware stack for subroutine calls and a programmable watchdog timer for safe recovery from code lockups. The MQFP-44 package offers ample I/O for motor, display, and instrumentation applications, while commercial temperature grade (0 °C to +70 °C) targets consumer and industrial environments. The 'T' suffix denotes tape-and-reel packaging for high-volume assembly, and the 'PQ' package code designates the plastic MQFP form factor. Typical applications include motor control, industrial automation, HVAC controllers, security and access systems, and instrumentation front-ends. The deterministic instruction timing makes the part effective for closed-loop control where predictable interrupt latency is required. When designing with this device, plan for an external oscillator (crystal or resonator) since no internal RC is provided on the PIC16C64A, and ensure the brown-out reset configuration matches the application supply profile. The OTP memory requires pre-programming before PCB assembly for production units. This page synthesizes current distributor pricing, parametric drop-in alternatives from the same PIC16C family, and practical design notes not found in the standalone datasheet.

Cotización Contacto

PIC16C64AT-20E/PQ

PIC16C64AT-20E/PQ - 8-Bit 20MHz OTP MCU, 3.5KB | Microchip

The Microchip Technology PIC16C64AT-20E/PQ is a member of the PIC16CXX family of low-cost, high-performance, CMOS, fully-static, 8-bit microcontrollers. The device operates at up to 20MHz clock speed, integrates 3.5KB (2K x 14) of One-Time Programmable (OTP) program memory, 128 x 8 bytes of RAM, and is housed in a 44-pin MQFP (10x10 mm) surface-mount package supplied on Tape & Reel. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, RAM, and programmable I/O peripherals. Within the broader taxonomy, the PIC16C64A is an OTP variant of the PIC16C64 baseline - OTP devices are programmed once and cannot be erased, contrasting with UV-erasable EPROM and Flash (PIC16F) siblings. PIC microcontrollers sit in the 8-bit RISC category alongside the 8051 and AVR families, and serve as the lowest-cost general-purpose embedded controllers in the Microchip portfolio. Key features of the PIC16C64AT-20E/PQ include the Harvard RISC architecture with separate program and data buses, 33 digital I/O lines, a 20MHz internal oscillator input, capture/compare/PWM (CCP) module, USART, 8-channel 8-bit A/D converter, three timers, and an instruction set of 35 single-word instructions. The 'E' suffix designates the extended industrial temperature range of -40C to +125C, and the 'T' suffix denotes Tape & Reel packaging. The device is well suited to industrial control, automotive subsystem, and consumer product applications where cost-sensitive, deterministic 8-bit control is required. The PIC16C64AT-20E/PQ is built on Microchip's mature CMOS process and uses a 14-bit instruction word with a 12-bit program memory address space, supporting 8K x 14 of addressable program memory. Its Harvard architecture allows simultaneous instruction fetch and data access, enabling most instructions to execute in a single instruction cycle (200ns at 20MHz). Power consumption is optimized through SLEEP mode and a programmable Watchdog Timer, making it suitable for battery-powered or low-duty-cycle embedded designs. Typical applications include industrial control, automotive body and chassis electronics, consumer appliances, and general-purpose embedded control systems. The 33 I/O pins and integrated peripherals allow the device to replace multiple discrete logic ICs in cost-sensitive designs.

Cotización Contacto

PIC16C64AT-20E/PT

PIC16C64AT-20E/PT - 8-bit OTP MCU, 20MHz, 44-TQFP | Microchip

The Microchip Technology PIC16C64AT-20E/PT is an 8-bit CMOS microcontroller from the PIC16C family, featuring a 20 MHz maximum operating frequency, 3.5 KB (2K x 14) of One-Time-Programmable (OTP) program memory, and 128 bytes of RAM, housed in a 44-pin TQFP (10x10 mm) surface-mount package. The device integrates 33 digital I/O pins, two 8-bit and one 16-bit timer/counter modules, a 10-bit multi-channel Analog-to-Digital Converter, and serial connectivity through I2C and SPI peripherals, making it a versatile general-purpose embedded controller. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral interfaces on one die, enabling compact, low-power embedded designs. PIC16C-series OTP MCUs belong to the broader 8-bit microcontroller category, sitting hierarchically above general-purpose microcontrollers, microcontrollers, and semiconductor integrated circuits. They are characterized by a RISC-based Harvard architecture with separate program and data buses, deterministic interrupt latency, and OTP ROM for code storage in cost-sensitive or short-run production. Key features of the PIC16C64AT-20E/PT include a wide operating voltage range of 2.5 V to 6.0 V, brown-out detect and reset (BOD/BOR) for safe power-up behavior, a power-on reset (POR) circuit, a watchdog timer (WDT) for runaway code recovery, and pulse-width modulation (PWM) outputs suitable for motor or lighting control. The integrated 10-bit ADC provides analog signal acquisition with up to 8 input channels, while the synchronous serial port supports both SPI and I2C master/slave protocols for sensor and peripheral expansion. Architecturally, the PIC16C64A employs a 14-bit instruction word with a single accumulator-based working register (WREG) and a small file-register map, delivering deterministic execution at 4 clock cycles per instruction (200 ns per instruction at 20 MHz). The CMOS process technology yields low power consumption suitable for battery-backed industrial control, automotive body electronics, and appliance subsystems, with sleep current low enough for long-term standby operation. Typical applications include industrial control panels, HVAC sensor interfaces, motor control boards, automotive body modules, appliance user interfaces, and general-purpose embedded controllers in the PIC16C legacy ecosystem. The 44-TQFP package supports compact, high-density PCB layouts and is compatible with standard SMT assembly lines. When designing with the PIC16C64AT-20E/PT, ensure that MCLR is properly pulled high through a resistor-capacitor network, and place decoupling capacitors (100 nF and 10 uF) close to the VDD/VSS pairs. Note that the OTP variant cannot be reprogrammed, so choose the flash-based PIC16F877A or PIC16F887 if in-system firmware updates are required.

Cotización Contacto

PIC16C64AT-20I/PQ

PIC16C64AT-20I/PQ - 8-Bit 20MHz OTP MCU, 3.5KB | Microchip

The Microchip Technology PIC16C64AT-20I/PQ is an 8-bit RISC microcontroller from the PIC® 16C family with 20 MHz maximum clock speed, 3.5 KB (2K x 14) of One-Time-Programmable (OTP) program memory, 128 bytes of RAM, and 33 programmable I/O pins, housed in a 44-pin MQFP (10x10 mm) surface-mount package. It operates from a 4 V to 6 V supply across the industrial temperature range of -40 °C to +85 °C, supporting I2C and SPI serial communication, and is specified at 20 MHz across that full supply window. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral interfaces onto one die. The PIC16CXX family is built on a fully-static CMOS architecture with a Harvard memory layout, meaning the program and data buses are physically separate. The C family is the classic OTP lineage that preceded the Flash-based F series; OTP parts are programmed once with a device programmer and cannot be electrically erased, which suits cost-sensitive production runs. Within the power-management IC hierarchy, this part sits at the controller/signal-processing tier alongside 8-bit microcontrollers from 8051, AVR, and HC11 families. Key features include a 14-bit instruction set optimized for compact code, a hardware USART for asynchronous serial links, an 8-bit parallel slave port for bus expansion, and a programmable watchdog timer with its own on-chip RC oscillator for fail-safe operation. The 33 I/O pins are grouped into five ports (PORTA–PORTE), each capable of sourcing or sinking sufficient current to drive LEDs and small relays directly. Brown-out-reset circuitry holds the part in reset when VDD dips below a programmable threshold, preventing code corruption from indeterminate supply rails. Architecture-wise, the PIC16C64A integrates an 8-level hardware stack for subroutine nesting, a 14-bit program counter that addresses the full 8K x 14 OTP space, and an interrupt controller handling up to 12 sources including external edge-triggered events. The core executes most instructions in a single 200 ns instruction cycle at 20 MHz, delivering roughly 5 MIPS of throughput. A 5-bit port-RA multiplexed analog comparator and two analog comparators further extend the analog front-end without external ICs. Typical applications include industrial automation controllers, consumer-electronics user-interface boards, automotive body and convenience modules (with PIC16F variants recommended for new designs), appliance control panels, and remote sensor signal-conditioning front-ends. Designers continue to specify this OTP part where mature firmware is locked and per-unit cost is critical. A practical design consideration is the OTP memory: firmware must be fully validated, since field firmware updates are impossible. For new designs, consider the pin-compatible PIC16F877A (Flash) variant to gain in-circuit reprogrammability without changing the PCB layout.

Cotización Contacto

PIC16C65A-04/L

PIC16C65A-04/L - 8-bit 4MHz 7KB OTP MCU 44-PLCC | Microchip

The Microchip Technology PIC16C65A-04/L is a member of the PIC16CXX family of low-cost, high-performance CMOS, fully-static 8-bit microcontrollers housed in a 44-pin PLCC (J-Lead) package. It integrates a 4 MHz RISC CPU core, 7 KB of One-Time-Programmable (OTP) program memory organized as 4K x 14 bits, 192 bytes of RAM, and 33 digital I/O lines. The '04' speed grade denotes a 4 MHz oscillator maximum, while the 'L' suffix indicates the PLCC lead-form. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, and peripheral interfaces on one die. The PIC16C65A-04/L belongs to the 8-bit MCU -> microcontroller -> embedded controller -> semiconductor hierarchy, sitting within Microchip's classic mid-range PIC16 architecture widely used in industrial control and embedded designs. Key features include 35 single-word instructions (most executing in one instruction cycle, with branches in two), a wide operating voltage range, and low power consumption: 5 mA typical at 5 V/4 MHz and 15 uA typical at 3 V/32 kHz. The fully static design allows the clock to be stopped without losing register state, and the device supports commercial, industrial, and extended temperature ranges. The integrated peripherals include timers, an 8-bit A/D converter, USART, and capture/compare/PWM modules. Architecturally, the PIC16C65A-04/L uses a Harvard-style RISC core with separated program and data buses, enabling simultaneous instruction fetch and operand access. The 14-bit wide program memory word yields more efficient instruction encoding than 8-bit CISC cores, and the OTP EPROM process technology allows one-time factory or in-circuit programming using a standard device programmer. Typical applications include industrial automation controllers, motor control subsystems, automotive body electronics, smart sensor interfaces, and embedded data acquisition systems. The 33 I/O lines and integrated peripherals make it well suited to medium-complexity embedded designs that need deterministic real-time response. When designing with this MCU, ensure decoupling capacitors are placed within 5 mm of VDD pins and that unused I/O pins are configured as outputs to minimize current consumption. OTP parts cannot be re-programmed in-circuit; choose a flash-based PIC16F equivalent if firmware revision cycles are anticipated. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the PIC16C65A-04/L that are not aggregated on the manufacturer datasheet alone.

Cotización Contacto

PIC16C65A-04/P

PIC16C65A-04/P - 8-Bit 4MHz 7KB OTP MCU 40-PDIP | Microchip

The Microchip Technology PIC16C65A-04/P is an 8-bit CMOS microcontroller built on Microchip's PIC16 family architecture, operating at 4 MHz with 7 KB (4K x 14) of one-time-programmable (OTP) program memory in a 40-pin PDIP through-hole package. According to the Microchip datasheet, the device provides 192 bytes of RAM, 33 digital I/O lines, three timer/counter modules, two capture/compare/PWM (CCP) modules, a synchronous serial port (SSP) supporting SPI and I2C, a USART, and an 8-bit analog-to-digital converter (ADC) with up to 8 input channels. What is an OTP microcontroller? An OTP (one-time-programmable) microcontroller is a class of embedded controller in which the on-chip program memory can be written only once by the user. OTP MCUs sit in the hierarchy of microcontrollers between mask-ROM parts (factory-programmed, lowest cost at high volume) and Flash-based parts (rewritable in-circuit). Because they require no quartz window for UV erasure, OTP packages are cheaper to produce and physically smaller, which is why PIC16C65A-04/P is offered in the low-cost plastic PDIP-40 form factor. In the modern product hierarchy, OTP parts are a subset of one-time-programmable memory MCUs, which themselves sit under microcontrollers -> embedded controllers -> semiconductor ICs. Key specifications of the PIC16C65A-04/P include 4 MHz maximum clock (the -04 speed grade), 200 ns instruction cycle, 35 single-word RISC instructions, 8-level deep hardware stack, 14-bit instruction word, 8-bit data path, 8-channel 8-bit ADC, two 8-bit timers plus one 16-bit timer, USART, SSP, and two CCP modules. Power supply range is 2.5 V to 6.0 V; the device operates across commercial (0 °C to +70 °C) and industrial (-40 °C to +85 °C) temperature ranges, with typical supply current of <2 mA at 5 V / 4 MHz and less than 1 µA in sleep mode. Architecture-wise, the PIC16C65A is built on a Harvard RISC core that fetches instructions in a single cycle (except program branches, which take two cycles). This is the same family as the PIC16C66 and PIC16C67, sharing peripheral set and pinout in the 40-pin PDIP package, with the -A silicon revision adding improvements in oscillator robustness and ADC linearity versus the original PIC16C65. The -04 speed grade is the 4 MHz part, complemented by -10 (10 MHz) and -20 (20 MHz) grades in the same family. Typical applications include industrial control logic, motor drive interfacing, instrumentation front-ends, HVAC controllers, security and access panels, automotive body electronics, embedded data acquisition, and any 8-bit control loop that needs ADC, PWM, and serial communication on a single low-cost chip. The 40-pin PDIP form factor makes it convenient for through-hole prototyping, breadboarding, educational kits, and legacy maintenance designs where the same socket pattern must be preserved across product revisions. A key design consideration: because this is an OTP part, firmware bugs cannot be patched in the field - designers must validate code on a windowed (JW) or Flash sibling (PIC16F77) before committing to the OTP build. Also note the A-suffix in PIC16C65A denotes the second die revision, which has minor register differences versus the original PIC16C65 (revocation of the PCON<POR> bit and revised oscillator startup). This page synthesizes distributor pricing, verified same-family and cross-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC16C65A-04/PQ

PIC16C65A-04/PQ - 8-Bit 4MHz 7KB OTP MCU 44-MQFP | Microchip

The Microchip Technology PIC16C65A-04/PQ is an 8-bit CMOS EPROM-based microcontroller from the PIC16C6X family, offering 7KB (4K x 14) of One-Time-Programmable (OTP) program memory in a 44-pin MQFP (10x10 mm) surface-mount package. It operates at up to 4 MHz clock speed with 192 bytes of RAM, 33 digital I/O pins, and a wide 4.0V to 6.0V supply range, optimized for high-performance RISC control with only 35 single-word instructions to learn. Background: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and programmable I/O peripherals. PIC microcontrollers from Microchip Technology use a Harvard RISC architecture, separating program and data buses to allow instruction fetch and operand access in a single cycle. The PIC16C family specifically targets cost-sensitive embedded control and is a predecessor to the flash-based PIC16F line. Key features include a fully static design that supports DC to 4 MHz operation (with -04 speed grade), low-power consumption of 15 uA typical at 5V/4 MHz and 1 uA typical at 3V/32 kHz, and a high-performance RISC CPU with single-cycle instructions except for program branches which take two cycles. The part supports commercial, industrial, and extended temperature ranges, making it suitable for both consumer and harsh-environment deployments. Architecturally, the PIC16C65A combines an 8-bit ALU with a 14-bit instruction word, 8-level hardware stack, and a powerful set of peripherals including timers, a synchronous serial port (SSP) supporting SPI and I2C, a USART, and an 8-bit parallel slave port for external memory or bused interfaces. This integration allows level-C back-channel communication with peripheral ASICs without external glue logic. Typical applications include industrial automation controllers, motor control front-ends, sensor signal conditioning, embedded display drivers, and legacy replacement of older 8051-based designs. Its OTP program memory and EPROM windowed variants simplify field programming during prototyping and low-volume production. When designing with this MCU, ensure the oscillator configuration matches the application: the -04 speed grade limits the clock to 4 MHz, so for higher throughput the PIC16C65A-10 or PIC16C65A-20 variants are required. Plan for a 1-2 ms power-on delay before code execution to allow the oscillator to stabilize. This page synthesizes distributor pricing, package dimensions, and drop-in alternatives drawn from across Microchip's PIC16C6X portfolio, providing practical sourcing and engineering context not found in the standalone datasheet.

Cotización Contacto

PIC16C65A-04E/L

PIC16C65A-04E/L - 8-bit OTP MCU, 7KB EPROM, 33 I/O, 44-PLCC | Microchip

The Microchip Technology PIC16C65A-04E/L is a member of the PIC16C6X family of low-cost, high-performance, CMOS, fully-static 8-bit microcontrollers housed in a 44-pin PLCC (J-Lead) windowed ceramic package. It integrates 7KB of EPROM program memory, 192 bytes of RAM, and 33 digital I/O pins, and operates from a 4.0V to 5.5V supply with a maximum clock speed of 10 MHz (the "-04" speed grade). A microcontroller (MCU) is a single-chip computer that combines a CPU, memory, and programmable peripherals. The PIC16C6X family uses a Harvard-architecture RISC core with only 35 single-word instructions, where all instructions execute in a single cycle except program branches (two cycles). This simplified instruction set enables deterministic timing and compact code density, making PIC MCUs popular for embedded control, instrumentation, and legacy industrial designs. Key features of the PIC16C65A-04E/L include 8-channel 8-bit ADC, two 8-bit timers plus one 16-bit timer with capture/compare/PWM, a synchronous/asynchronous USART with addressable SPI/I2C master mode, and a programmable watchdog timer with its own on-chip RC oscillator. The device supports commercial, industrial, and extended temperature ranges, with the "/L" suffix indicating the PLCC package and "-04E" indicating the 4 MHz extended-temperature speed grade. Typical applications include industrial control logic, motor drive interfaces, sensor signal conditioning, and legacy embedded systems where EPROM-based, windowed-ceramic parts are required for in-circuit reprogramming during development or field service. The high number of I/O pins (33) supports keypad scanning, LED multiplexing, and parallel bus expansion. When designing with this device, designers should account for the 4 MHz maximum oscillator at 5V and verify that the chosen timer/capture bandwidth is sufficient for the target application. The windowed ceramic package allows UV erasure, which is useful for prototyping but typically not for volume production; for that, consider the OTP-only or flash-based PIC16F equivalent family members.

Cotización Contacto

PIC16C65A-04E/P

PIC16C65A-04E/P - 4MHz 8-Bit OTP MCU, 7KB EPROM, 40-PDIP | Microchip

The Microchip Technology PIC16C65A-04E/P is an 8-bit CMOS RISC microcontroller from the PIC16C6x family, housed in a 40-pin PDIP (0.600 inch, 15.24 mm) through-hole package and qualified to the Extended temperature grade (-40C to +125C). It integrates 7 KB (4K x 14) of OTP program memory, 192 bytes of data RAM, 33 digital I/O lines, and a 4 MHz internal clock rate derived from an external oscillator. The device operates across a 2.5 V to 6.0 V supply range with low power consumption of approximately 15 uA typical at 5 V / 4 MHz. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripherals on one silicon die. Within the wider taxonomy, this part sits in the microcontroller -> microprocessor -> semiconductor -> integrated circuit hierarchy. PIC MCUs implement a Harvard RISC architecture with 35 single-word instructions and a 200 ns instruction cycle at 4 MHz, which is why PIC parts are commonly classified as low-cost, easy-to-program 8-bit controllers. Key features of the PIC16C65A-04E/P include an internal 8-bit timer/counter, a watchdog timer, an analog comparator, and a synchronous/asynchronous serial port (USART/SCI). Its fully static design means the clock can be stopped without losing register state, enabling low-power sleep/idle modes. The Extended temperature suffix "E" qualifies the part for harsh industrial environments that exceed the commercial 0C to +70C range. Architecturally, the PIC16C65A-04E/P uses a 14-bit instruction word with an 8-bit data path, separating program and data buses so an instruction can be fetched while the previous one is executing. OTP (one-time programmable) EPROM program memory allows fast prototyping but only supports a single programming cycle - this differs from flash-based PIC16F successors which offer in-circuit reprogramming. Typical applications include industrial control logic, motor drivers, sensor interfacing, and legacy embedded systems that still require a 40-pin PDIP footprint for through-hole assembly. Designers often choose this part when modern flash MCUs are unavailable or when maintaining drop-in compatibility with older 40-pin PIC16 designs is mandatory. When designing with this MCU, plan the decoupling network carefully: place a 0.1 uF ceramic bypass close to VDD and add bulk capacitance for analog references. Programming the OTP device requires a compatible device programmer; once blown, the program memory cannot be erased, so verify firmware in a flash equivalent first. This page synthesizes distributor availability, same-family drop-in PIC alternatives, and design notes not collated in the original Microchip datasheet.

Cotización Contacto

PIC16C65A-04E/PQ

PIC16C65A-04E/PQ - 8-bit 4MHz MCU, 7KB OTP, 44-MQFP | Microchip

The Microchip Technology PIC16C65A-04E/PQ is an 8-bit RISC CMOS microcontroller from the PIC16C family, operating at up to 4 MHz with 7 KB (4K x 14) of One-Time-Programmable (OTP) EPROM program memory and 192 bytes of data RAM, housed in a 44-pin MQFP (10x10 mm) plastic package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, and peripherals around an 8-bit data bus. The PIC16C family uses a Harvard RISC architecture with only 35 single-word instructions, where most instructions execute in a single instruction cycle (4 clock periods). The PIC16C65A-04E/PQ sits within the broader PIC microcontroller hierarchy: PIC16C65A -> PIC16C6X sub-family -> PIC16C family -> 8-bit PIC microcontrollers -> Microchip MCU portfolio -> embedded semiconductors. Key features include 33 digital I/O pins, three serial communication peripherals (I2C/SPI via the Synchronous Serial Port, plus a USART), 8 channels of 8-bit analog-to-digital conversion, a Capture/Compare/PWM module, two 8-bit timers and one 16-bit timer, and a programmable watchdog timer. Power consumption is rated at 15 µA typical at 5 V/4 MHz and as low as 1 µA typical at 3 V/32 kHz, enabling low-power and battery-friendly designs. The "04E" suffix denotes a 4 MHz maximum clock with the Extended temperature range (-40C to +125C). Architecturally, the device is built on Microchip's high-performance CMOS EPROM technology with a fully static design that allows the clock to be stopped without losing register state. The 14-bit instruction word delivers compact code density, and the 8-bit-wide data path keeps peripheral interfacing straightforward for legacy 5 V designs. Brown-out Reset, Power-on Reset, and a Watchdog Timer with its own on-chip RC oscillator provide robust unsupervised operation in industrial environments. Typical applications include industrial control and automation, HVAC and appliance controllers, motor control front-ends, automotive body electronics, smart sensors, and legacy embedded systems requiring 5 V-tolerant I/O with USART, I2C, and SPI. The Extended temperature grade makes the part suitable for under-hood and outdoor installations. When designing with this part, ensure your firmware uses the PIC16C6X instruction set and that code does not exceed 4K instruction words. The OTP memory is one-time programmable, so plan for in-system programming or windowed Ceramic packages for prototype development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC16C65A-04E/PT

PIC16C65A-04E/PT - 8-bit PIC MCU 7KB OTP 4MHz 44-TQFP | Microchip

The Microchip Technology PIC16C65A-04E/PT is an 8-bit RISC microcontroller from the PIC16C family, integrating 7 KB of one-time-programmable (OTP) program memory (4K x 14), 192 bytes of data RAM, and 33 digital I/O lines in a 44-pin TQFP package rated for the industrial -40C to +125C extended temperature range. Operating from a 4 V to 6 V supply at a maximum clock of 4 MHz, the device delivers 200 ns instruction execution across 35 single-word instructions in the PIC RISC architecture. The PIC16C65A belongs to the 8-bit microcontroller (MCU) category, a class of single-chip microcontrollers that integrate CPU core, program memory, data RAM, peripherals and I/O into one package. Within that hierarchy the part sits under 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. PIC16C-series devices target low-cost, deterministic embedded control and remain popular where engineers need rapid interrupt response, simple instruction set, and decades of mature toolchain support from MPLAB IDE, MPASM assembler, and Hi-Tech C compilers. Key features include 192 bytes of general-purpose RAM, 33 digital I/O pins, a programmable code-protection scheme, an 8-bit timer/counter, a watchdog timer, and on-chip power-on reset / brown-out reset circuitry. Peripherals include USART, parallel slave port, capture/compare/PWM modules, and synchronous serial port hardware. The architecture supports direct, indirect and relative addressing modes plus a hardware multiply assist, giving the PIC16C65A strong interrupt latency performance for real-time control. Typical applications include industrial process control, instrumentation front-ends, motor control front-ends, building automation, low-power sensor hubs, and legacy embedded systems that require an OTP-programmed controller with extended-temperature qualification. Designers migrating from windowed EPROM parts often choose PIC16C65A-04E variants (E = extended temperature) for harsh-environment deployments. When designing with this device, note that the '04' suffix denotes 4 MHz maximum clock and the 'E' suffix denotes the extended -40C to +125C temperature grade. The PT suffix marks the 44-pin TQFP (10x10 mm) package, which requires 1.0 mm PCB pad pitch. The PIC16C65A-04E/PT is OTP, so firmware must be fully validated before programming; windowed JW-package variants exist for prototype development. This page synthesizes distributor stock, drop-in 44-TQFP pin-compatible alternatives, application circuit guidance, and lifecycle notes not found in the manufacturer datasheet alone, providing a single reference for engineers evaluating PIC16C65A-04E/PT for new designs or maintenance of legacy systems.

Cotización Contacto

PIC16C65A-04I/P

PIC16C65A-04I/P - 8-Bit 4MHz OTP MCU 7KB EPROM | Microchip

The Microchip PIC16C65A-04I/P is an 8-bit CMOS OTP microcontroller based on the PIC16C family RISC architecture, featuring 7KB (4K x 14) one-time-programmable EPROM program memory, 192 bytes of RAM, and 33 digital I/O pins, housed in a 40-pin PDIP (DIP-40) through-hole package. The -04 speed grade denotes a 4 MHz maximum oscillator input, and the -I suffix denotes the industrial temperature range of -40C to +85C. An 8-bit microcontroller (MCU) is a programmable digital logic device that combines a CPU, non-volatile program memory, working RAM, and configurable peripheral blocks (I/O, timers, communication interfaces) on a single silicon die. PIC microcontrollers follow the RISC (Reduced Instruction Set Computer) philosophy and use a Harvard architecture with separate program and data buses, delivering deterministic instruction execution in as little as 200 ns. The PIC16C family sits within the broader hierarchy: MCU -> 8-bit MCU -> PIC16C family -> PIC16C6x sub-family -> PIC16C65A device. EPROM-based members are one-time-programmable and intended for low-volume production or legacy socket replacement. Key features include 33 I/O pins arranged across multiple ports (PORTA, PORTB, PORTC, PORTD, PORTE), three timers (TMR0, TMR1, TMR2), a 5-channel 8-bit Analog-to-Digital Converter, and serial communication peripherals including SSP for I2C/SPI and a USART for UART. Additional features include an 8-bit parallel slave port, watchdog timer with on-chip RC oscillator, power-on reset, brown-out reset, and power-saving SLEEP mode. The device operates from 2.5V to 6.0V. The PIC16C65A uses a 14-bit instruction word with 35 single-word instructions, allowing compact code density. The Harvard bus structure enables simultaneous instruction fetch and data access, contributing to the one-instruction-per-cycle (except branches) throughput. External interrupt, RB port-change interrupt, and multiple peripheral interrupt sources support real-time event handling in embedded systems. Typical applications include industrial control systems, automotive body and chassis electronics, white goods and appliance controllers, security and access control panels, sensor signal conditioning front-ends, and legacy embedded system maintenance. The DIP-40 package supports breadboard and socketed designs favored in education, prototyping, and field-replaceable assemblies. When designing with this device, note that EPROM windows are not present on plastic PDIP packages; code must be committed via device programmer at production. Use ICD or compatible in-circuit debugger header for development. Ensure the Vdd/Vss decoupling follows the manufacturer recommended layout (100 nF ceramic within 5 mm of each supply pin) to maintain ADC accuracy. This page synthesizes distributor availability, drop-in alternatives, and practical design considerations not consolidated on the manufacturer datasheet.

Cotización Contacto

PIC16C65A-04I/PQ

PIC16C65A-04I/PQ - 4MHz 8-bit MCU, 7KB OTP, 44-MQFP | Microchip

The Microchip Technology PIC16C65A-04I/PQ is an 8-bit CMOS RISC microcontroller from the PIC16C6X family, featuring 7KB of one-time-programmable (OTP) program memory, 192 bytes of RAM, and 33 digital I/O lines, housed in a 44-pin Metric Quad Flat Pack (MQFP, 10x10 mm) package. It operates up to 4 MHz clock speed from a 4.0V to 5.5V supply and is rated for the industrial temperature range (-40C to +85C). What is an 8-bit OTP microcontroller? An 8-bit microcontroller integrates a CPU, program memory, RAM, and peripherals on a single die. OTP (One-Time-Programmable) memory uses EPROM cells that can be written once and erased only by UV exposure (through a windowed package). In the broader taxonomy, the PIC16C65A sits under microcontroller -> embedded MCU -> semiconductor device, and it belongs to Microchip's mid-range PIC16 family that uses a 14-bit instruction word. Key features include a high-performance RISC CPU with only 35 single-word instructions, all single-cycle except program branches (two cycles), and DC to 4 MHz operating speed. Power consumption is low at 5V/4 MHz (15 uA typical) and 3V/32 kHz (1 uA typical). The PIC16C65A integrates multiple peripherals: a USART for serial communication, an SSP module for SPI/I2C, capture/compare/PWM (CCP) modules, an 8-bit ADC, and two 8-bit timers plus one 16-bit timer with optional prescaler. The architecture uses a Harvard design with separate program and data buses, allowing instruction fetch and data access in a single clock cycle. This RISC-style approach delivers deterministic execution and predictable interrupt latency, which has made the PIC16 mid-range family a workhorse for industrial control and embedded applications since the 1990s. The 44-MQFP package provides 33 I/O pins - more than smaller PIC16C6X parts (28-pin) - while remaining compatible with the same instruction set and development toolchain. Typical applications include industrial automation controllers, sensor signal conditioning, motor control with PWM, serial communication bridges, embedded data acquisition, and legacy embedded-system upgrades. The wide industrial temperature range and OTP memory suit fixed-program production runs where field firmware updates are not required. Design tip: when migrating from the PIC16C65B or PIC16C65 to PIC16C65A, verify peripheral register maps; the 'A' revision changed ADC configuration bits. For modern designs, consider the flash-based PIC16F877A as a drop-in upgrade with the same 44-pin footprint but in-circuit reprogrammability. This page synthesizes distributor pricing, drop-in alternatives, and engineering design notes not typically presented in a single manufacturer datasheet view.

Cotización Contacto

PIC16C65A-10/L

PIC16C65A-10/L - 8-Bit 10MHz OTP MCU 7KB | Microchip

The Microchip Technology PIC16C65A-10/L is a high-performance 8-bit CMOS RISC microcontroller featuring a 10 MHz maximum clock input, 7 KB (4K x 14) on-chip One-Time-Programmable (OTP) program memory, and 192 bytes of RAM, all housed in a 44-pin PLCC (J-Lead) package. It belongs to the PIC16C6X family of microcontrollers that use a modified Harvard architecture with separate program and data buses, enabling single-cycle instruction execution for most opcodes and deterministic timing critical for embedded control. What is an OTP microcontroller? An OTP (One-Time-Programmable) microcontroller contains program memory that can be written once during programming and cannot be erased or rewritten, making it well suited for volume production where firmware is stable and final. The PIC16C65A is part of the broader 8-bit MCU category, sitting within the PIC family hierarchy of PIC16C -> PIC16 -> PIC microcontroller -> 8-bit MCU -> microcontroller -> embedded processor. The 'C' in PIC16C denotes CMOS EPROM technology, distinguishing it from later flash-based PIC16F variants. Key features include only 35 single-word instructions to learn, all single-cycle except program branches which are two cycles, a wide operating voltage range up to 6.0 V, and low power consumption of typically 15 uA at 5 V and 4 MHz, dropping to 1 uA at 3 V and 32 kHz. The device provides 33 digital I/O pins organized across multiple ports, three timer/counter modules, a synchronous serial port (SSP) supporting SPI and I2C, and a USART for asynchronous serial communication, enabling rich peripheral integration without external components. The PIC16C65A architecture features a 14-bit instruction word, 8-bit data path, and a hardware multiplier-free ALU optimized for byte-level bit manipulation. Its fully-static CMOS design allows the clock to be stopped without losing register state, useful for power-sensitive applications. The device also integrates a watchdog timer with its own on-chip RC oscillator for reliable operation, brown-out reset protection, and power-on reset circuitry. Typical applications include industrial automation and control, motor control (BLDC, stepper), embedded instrumentation with serial display interfaces, automotive body electronics, HVAC controllers, security and access systems, and general-purpose 8-bit embedded control in commercial and consumer products. Its 33 I/O pins provide ample connectivity for keypads, displays, sensors, and actuators. When designing with the PIC16C65A-10/L, consider that OTP memory is one-time-programmable and cannot be field-updated - use a flash-based PIC16F equivalent during prototyping. The /L suffix indicates the PLCC-44 package; ensure your PCB footprint matches JEDEC PLCC-44 with 1.27 mm pin pitch and J-lead terminations. This page synthesizes distributor pricing, drop-in PIC16C65A alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC16C65A-10/P

PIC16C65A-10/P - 8-Bit 10MHz OTP MCU, 7KB Flash | Microchip

The Microchip Technology PIC16C65A-10/P is an 8-bit CMOS microcontroller based on the PIC16C family, integrating 7KB (4K x 14) of One-Time-Programmable (OTP) program memory and 192 bytes of RAM in a 40-pin PDIP (DIP) through-hole package. It executes instructions at up to 10 MHz from an external oscillator, supports an operating voltage range of 4V to 6V, and provides 33 digital I/O pins suitable for embedded control. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, RAM, and peripherals on one die. The PIC16C family uses a Harvard RISC architecture with separate program and data buses, enabling single-cycle instruction execution for predictable timing. The '16C' OTP suffix means each unit is programmed once at production and cannot be electrically erased, making the part cost-optimized for high-volume embedded products whose firmware is finalized before deployment. Key features include three 8-bit timer/counters (Timer0, Timer1, Timer2), a 16-bit Capture/Compare/PWM module, a USART for asynchronous or synchronous serial, a Synchronous Serial Port (SSP) supporting SPI and I2C (master/slave), an 8-bit parallel slave port, and a watchdog timer with on-chip RC oscillator for safe recovery from code lockups. Brown-out reset and power-on reset are integrated for robust power-up behavior across commercial, industrial, and extended temperature grades. Typical applications include industrial control panels, HVAC damper and motor controllers, automotive body modules, instrumentation front panels, smart appliance control boards, and any 5V through-hole legacy design where pin compatibility with the classic PIC16C6x family is required. The 33 I/O pins and rich peripheral set enable direct interface to keypads, LED or LCD displays, sensors, and serial peripherals without external glue logic. When designing with this part, allocate a socket for in-system programming if field firmware updates are anticipated, since OTP cannot be rewritten after the windowed or plastic package is sealed. Place a 0.1uF decoupling capacitor within 5 mm of VDD and reserve a footprint for the MCLR pull-up and the standard 4 MHz to 20 MHz crystal with two 15-33 pF load capacitors as recommended in the Microchip PIC16C6x datasheet family. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a faster path from concept to validated production BOM.

Cotización Contacto

PIC16C65A-10/PQ

PIC16C65A-10/PQ - 8-bit OTP MCU 7KB 33 I/O | Microchip

The Microchip Technology PIC16C65A-10/PQ is an 8-bit, One-Time Programmable (OTP) CMOS RISC microcontroller delivering 7KB of program memory, 192 bytes of RAM, and 33 digital I/O pins, housed in a 44-pin QFP (MQFP) package. It operates from 4.0V to 6.0V and supports DC to 10 MHz clock input with a 10 MHz instruction execution rate. The PIC16CXX architecture provides only 35 single-word instructions, all single-cycle except program branches, enabling compact deterministic control loops in embedded applications. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory, RAM, and programmable peripheral I/O into a single chip, forming the lowest-tier decision-making element of an embedded system. Within the broader semiconductor taxonomy, an MCU belongs to integrated circuits > microcontrollers > 8-bit microcontrollers > CMOS RISC microcontrollers. OTP variants like the PIC16C65A are typically used in volume production where the firmware is fixed and re-programming is unnecessary, while EPROM/flash variants are reserved for development. The PIC16C65A sits in Microchip's mid-range PIC16 family, between PIC16C6X baseline and PIC16C7X enhanced peripherals. Key features of the PIC16C65A-10/PQ include a power-on reset, brown-out detection (BOD), watchdog timer (WDT) with on-chip RC oscillator, code-protection bit, programmable code-protection, and four hardware interrupt sources. It provides three timer/counter modules (Timer0, Timer1, Timer2) supporting capture/compare/PWM operation, a USART serial port, and an 8-bit parallel slave port. The 33 I/O pins are grouped into five ports (PORTA through PORTE) with programmable direction registers, supporting direct LED drive, key matrix scanning, and analog comparator inputs via PORTE. The PIC16C65A core implements a Harvard architecture with separate program and data buses, enabling simultaneous instruction fetch and operand access. Its CMOS process yields typical active current around 5 mA at 10 MHz and standby current below 5 uA, suitable for battery-backed industrial and consumer products. The OTP memory is programmed using Microchip's PM3 universal programmer or compatible gang programmers; once written, the bit cannot be erased, so OTP parts are final-state production parts. Typical applications include industrial process controllers, motor drive front-ends, HVAC fan/pump controls, appliance controllers, automotive body modules, instrumentation front panels, and security alarm panels. The 33 I/Os allow direct keypad + LCD interface without external glue logic, while the USART enables RS-232/RS-485 communication with an external transceiver. When designing with the PIC16C65A-10/PQ, ensure the supply stays within 4.0V-6.0V (this part is not 3.3V tolerant) and add a 100 nF decoupling capacitor close to VDD. Because this is an OTP device, a parallel production programmer strategy must be planned early to avoid scrapped PCBs if firmware revisions occur late in the design cycle. This page synthesizes distributor pricing, drop-in alternatives within the same 44-pin QFP package, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC16C65A-10/PT

PIC16C65A-10/PT - 8-bit OTP MCU 7KB 10MHz TQFP-44 | Microchip

The Microchip Technology PIC16C65A-10/PT is an 8-bit RISC microcontroller in the PIC16C family, featuring 7KB of One-Time Programmable (OTP) program memory (4K x 14 words) and 192 bytes of RAM, operating at up to 10 MHz. Housed in a 44-pin TQFP surface-mount package, it provides 33 general-purpose digital I/O pins and integrated peripherals including I2C (MSSP/SPI mode), SPI, and USART (RS-232/RS-485 capable) serial channels. The 10 MHz clock speed supports 100 ns minimum instruction cycle, with 14-bit wide instructions and 8-bit data path typical of the mid-range PIC16C architecture. The PIC microcontroller is an 8-bit Harvard-architecture RISC processor family developed by Microchip Technology, widely used in embedded control applications. Microcontrollers (MCUs) integrate a CPU core, program memory, working RAM, and peripheral interfaces on a single silicon die, and they sit at the lowest level of the embedded system hierarchy: MCU -> microcontroller -> embedded controller -> semiconductor IC. Mid-range PIC16C devices like the PIC16C65A add interrupt-driven I/O, on-chip timers, and synchronous/asynchronous serial ports while keeping the instruction set small enough for deterministic real-time control. The 'A' suffix denotes the enhanced silicon revision with bug fixes over the original PIC16C65 silicon, and the 'C' in PIC16C indicates CMOS fabrication for low power consumption. Key features include four 8-bit I/O ports (PORTA through PORTE, with PORTB/C supporting high-current drive), a 16-bit timer/counter (TMR1) plus two 8-bit timers (TMR0, TMR2), a 10-bit-resolution ADC with 8 input channels (on most PIC16C65A package options), and a watchdog timer for fault recovery. Brown-out-reset, power-on-reset, and an in-circuit serial programming interface are integrated. Operating voltage spans 2.5V to 5.5V (commercial) or 2.5V to 6.0V (industrial, /I suffix) at industrial temperature range -40C to +85C. The PIC16C65A uses Microchip's mid-range 14-bit instruction set and shares peripheral architecture with the PIC16C63 and PIC16C64 families, enabling code portability across the family. The Harvard bus structure separates program and data memory for single-cycle instruction fetch, and the 8-level hardware stack supports nested subroutine calls. Sleep mode current is typically < 1 uA, making the part suitable for battery-powered instruments. Compared to modern PIC16F1xxx flash parts, the OTP-only PIC16C65A is intended for low-to-medium volume production or legacy system replication. Typical applications include industrial control and automation systems, automotive body and chassis electronics (with automotive-grade /Q suffix variants), HVAC controls, appliance controllers, instrumentation front-ends, and embedded sensor interfaces where the 33 I/O pins directly drive relays, keypads, and LED/LCD panels. The integrated UART also suits legacy point-of-sale terminals and RS-485 networked devices. When designing with this part, remember that OTP memory cannot be erased electrically; prototypes should be developed on the pin-compatible PIC16F877A flash part, then moved to PIC16C65A for production. A 4 MHz to 10 MHz crystal or ceramic resonator is required on OSC1/OSC2, and decoupling capacitors must be placed within 5 mm of VDD/VSS pins for noise immunity. This page synthesizes distributor pricing, drop-in alternatives within the PIC16C family, and practical design notes not consolidated in the manufacturer datasheet.

Cotización Contacto

PIC16C65A-10E/PQ

PIC16C65A-10E/PQ - 8-Bit CMOS MCU, 7KB OTP, 10MHz | Microchip

The Microchip Technology PIC16C65A-10E/PQ is an 8-bit RISC CMOS microcontroller in the PIC16C family, delivering 10 MHz maximum clock operation with 7 KB of One-Time Programmable (OTP) program memory (4K x 14 organization) in a 44-pin MQFP package. The "-10" suffix indicates a 10 MHz clock rating and the "E" suffix denotes the Extended operating temperature range. An 8-bit CMOS microcontroller is a single-chip computer built on a Harvard RISC architecture, integrating a CPU, program memory, data RAM, and peripheral interfaces on one die. Within the broader taxonomy, an 8-bit MCU sits below 16-bit and 32-bit microcontrollers in arithmetic width and instruction complexity, but above fixed-function logic ICs in programmability, and belongs to the power-managed embedded computing category in modern electronic systems. The PIC16C6X family uses a 14-bit instruction word optimized for compact code density. Key specifications include a 4.5 V to 6.0 V supply range, maximum supply current of 30 mA, fully-static design supporting DC to 10 MHz operation, and low-power consumption of 15 µA typical at 5 V/4 MHz and 1 µA typical at 3 V/32 kHz. The device offers 35 single-word instructions with all single-cycle execution except program branches (two-cycle), and integrates multiple peripheral interfaces including parallel ports and serial communication. The architecture uses a RISC CPU core with separate program and data buses, enabling simultaneous instruction fetch and data access. This Harvard architecture, combined with CMOS EPROM/ROM technology, gives the PIC16C65A its characteristic deterministic timing, low power, and high code efficiency that made the PIC16 family a workhorse of industrial embedded design. Typical applications include industrial control systems, automotive subsystems, and consumer electronics requiring reliable 8-bit processing with simple peripheral integration. The Extended temperature grade supports operation in thermally demanding environments such as under-hood automotive modules and factory automation controllers. When designing with this device, note that OTP memory requires factory or pre-production programming; field firmware updates are not possible. Engineers transitioning from PIC16C65A to newer PIC18 or dsPIC parts should review peripheral register changes and instruction-set differences before PCB rework.

Cotización Contacto

PIC16C65A-10I/L

PIC16C65A-10I/L - 8-Bit 10MHz OTP MCU 7KB | Microchip

The Microchip Technology PIC16C65A-10I/L is an 8-bit RISC CMOS microcontroller built around the PIC16C6X core, integrating 7KB (4K x 14) of One-Time Programmable (OTP) EPROM program memory and 192 bytes of data RAM in a 44-pin PLCC (J-lead, package code QCCJ) industrial-temperature package. It executes instructions at a 10 MHz maximum clock input while drawing only 15 uA typical at 5V / 4 MHz and 1 uA typical at 3V / 32 kHz, with a fully-static design that supports DC to 20 MHz clock input. The device exposes 33 digital I/O pins, supports a wide operating voltage range up to 6.0V, and is offered in commercial, industrial, and extended temperature grades; the "/L" suffix denotes the 44-pin PLCC industrial-grade (-40C to +85C) option. An 8-bit microcontroller (MCU) is a small, self-contained computing system on a single chip that integrates a CPU, program memory (ROM/EPROM/Flash/OTP), working RAM, and programmable I/O peripherals. The PIC16C6X family uses a Harvard RISC architecture with separate program and data buses, only 35 single-word instructions, and all single-cycle instruction execution except program branches (which take two cycles). In the system hierarchy this places PIC16C65A-10I/L at: 8-bit MCU -> RISC microcontroller -> embedded controller -> semiconductor IC. Key features include 33 I/O lines spread across multiple ports, a peripheral feature set derived from PIC16C66/67 (synchronous/asynchronous serial ports, PWM, capture/compare timers, 8-bit A/D converter channeling), brown-out reset, watchdog timer, and low-power SLEEP/idle modes. The OTP program memory is one-time programmable using programmers such as MPLAB PM3, which is a hard requirement for production designs where firmware is finalized. Typical applications include industrial control panels, instrumentation, motor control front-ends, sensor interfacing nodes, and legacy embedded systems that require a robust 8-bit core with abundant I/O. Industrial-grade temperature rating (-40C to +85C) and the 44-pin PLCC package make it a strong fit for through-hole-style industrial backplanes and field-replaceable modules. When designing with this device, ensure that the chosen programmer supports the PIC16C65A OTP window (PM3 recommended) and that the brown-out and watchdog configuration bits match the application's fault-recovery strategy. Note that OTP parts cannot be re-programmed, so firmware validation must be finalized before production programming. This page synthesizes distributor pricing, drop-in same-brand and cross-brand alternatives in the 44-PLCC footprint, and practical design notes not found in the standalone manufacturer datasheet.

Cotización Contacto

PIC16C65A-10I/PQ

PIC16C65A-10I/PQ - 8-bit RISC MCU, 7KB OTP, 44-MQFP | Microchip

The Microchip PIC16C65A-10I/PQ is an 8-bit RISC microcontroller from the PIC16C6X family, featuring 7 KB of OTP program memory, 192 bytes of data RAM, and a maximum clock speed of 10 MHz, housed in a 44-pin MQFP (PQ) package rated for the industrial -40C to +85C temperature range. The device integrates I2C, SPI, and USART serial peripherals, three timers, two PWM channels, and a watchdog timer, making it a self-contained control platform for the implemented product design. A PIC microcontroller is a compact, Harvard-architecture microcontroller that integrates a CPU, program memory, RAM, and peripheral peripherals into a single chip. PIC16C6X devices sit in the mid-tier of Microchip's 8-bit portfolio (PIC16 -> PIC microcontroller -> microcontroller -> embedded processor -> semiconductor), optimized for cost-sensitive industrial and embedded applications that need deterministic interrupt response and low power consumption rather than raw compute throughput. Key features of the PIC16C65A-10I/PQ include a RISC CPU with 35 single-word instructions, fully static design supporting DC to 10 MHz clock input, and wide operating voltage range typical of 2.5V to 6.0V. The 7 KB OTP program memory and 192-byte RAM are sized for moderate firmware complexity (control loops, protocol stacks, sensor interfacing). Industrial-grade -40C to +85C qualification, in-circuit serial programming capability, and a 44-pin MQFP footprint ease PCB integration in legacy and new industrial designs. The device uses CMOS EPROM/ROM technology, fully static logic, and a 14-bit instruction word. Low-power performance is characterized as <15 mA typical at 5V/4 MHz and <1 mA typical at 3V/32 kHz. Watchdog, power-on reset, brown-out detect, and code-protect features contribute to system robustness. Interrupts, a hardware USART, and capture/compare PWM blocks support motor control, instrumentation, and human-interface subsystems. Typical applications include industrial automation controllers, motor and solenoid drive control boards, instrumentation front-ends with serial communication to a host, and embedded sensor nodes using I2C/SPI. The 44-MQFP package and industrial temperature range also suit legacy replacement, factory automation, and harsh-environment monitoring designs. When designing with this part, plan OTP programming before final PCB assembly: OTP cannot be erased, so firmware must be validated on windowed or flash siblings first. The 44-pin footprint, 5V typical supply, and classic PIC16C6X peripherals make direct migration to PIC16F87X or PIC18 devices straightforward when more memory or in-system reprogrammability is needed. This page synthesizes distributor stock, parametric data, drop-in same-brand alternatives, and design considerations not consolidated in the legacy datasheet, helping engineers and buyers accelerate sourcing and PCB redesign decisions.

Cotización Contacto

PIC16C65A-10I/PT

PIC16C65A-10I/PT - 8-Bit 10MHz OTP MCU 7KB Flash 44-TQFP | Microchip

The Microchip Technology PIC16C65A-10I/PT is an 8-bit CMOS OTP microcontroller based on the PIC16CXX family, featuring 7KB (4K x 14) of program memory, 192 bytes of RAM, and 33 digital I/O pins housed in a 44-pin TQFP package. It operates at 10 MHz and supports a wide 2.5V to 6.0V supply range, delivering fully static operation suitable for battery-friendly and industrial embedded designs. An 8-bit microcontroller (MCU) is a small, low-power computer-on-a-chip integrating a CPU, RAM, program memory, and peripherals on a single die. It belongs to the broader category of embedded microcontrollers, which sit inside the hierarchy of microprocessors -> microcontrollers -> 8-bit microcontrollers -> PIC16C family. The PIC16C65A is part of Microchip's mid-range PIC16C OTP (One-Time-Programmable) lineage, chosen for its deterministic Harvard architecture, simple instruction set, and field-proven reliability in long-life industrial equipment. Key features include 33 I/O pins, three timers (Timer0, Timer1, Timer2), a 10-bit ADC, a USART for serial communication, and capture/compare/PWM (CCP) peripherals. Power consumption is rated at 5V/4 MHz at 15 uA typical and 3V/32 kHz at 1 uA typical, demonstrating low-power CMOS design that suits battery-backed instrumentation. Industrial temperature grade (-40C to +85C) is denoted by the 'I' suffix, and the OTP memory enables factory-programmed code storage for volume production. The PIC16C65A uses Microchip's RISC-based PIC16 architecture with 14-bit wide instructions, an 8-bit data path, and a two-stage pipeline for predictable single-cycle execution (200 ns per instruction at 10 MHz). The integrated 10-bit ADC supports up to 8 analog channels, enabling mixed-signal designs without an external converter. In-system serial programming (ICSP) is supported via dedicated RB6/RB7 pins, simplifying firmware upgrades on assembled boards. Typical applications include industrial control systems, sensor signal conditioning, motor control, white-goods appliances, and embedded instrumentation where deterministic response and long-term supply stability matter. The 33 I/O count makes it well suited to keypad scanning, LED multiplexing, and relay/SSR driver boards. When designing with this MCU, ensure the supply decoupling network includes a 0.1 uF ceramic capacitor close to VDD and a bulk tantalum/electrolytic capacitor to handle switching transients. Place the crystal or resonator within 1 cm of the OSC1/OSC2 pins to minimize clock jitter and EMI susceptibility. This page synthesizes Microchip datasheet specifications, distributor pricing, drop-in OTP and Flash alternatives, and practical design notes not consolidated on the official product page, helping engineers shorten BOM validation and component selection time.

Cotización Contacto

PIC16C65A-20/P

PIC16C65A-20/P - 8-Bit 20MHz 7KB OTP MCU 40-PDIP | Microchip

The Microchip Technology PIC16C65A-20/P is an 8-bit CMOS OTP (One-Time-Programmable) microcontroller from the PIC® 16C family, executing instructions at up to 20 MHz and integrating 7 KB (4K x 14) of program memory in a 40-pin PDIP (0.600 in, 15.24 mm) through-hole package. The device is built around Microchip's high-performance RISC CPU core that uses only 35 single-word instructions, with all instructions executing in a single cycle except for program branches which take two cycles, delivering near-1:1 MIPS/MHz throughput. An OTP-based microcontroller is a member of the broader microcontroller family (microcontroller -> embedded controller -> semiconductor IC) that integrates a CPU, non-volatile program memory, RAM, and programmable I/O into a single chip. OTP variants are programmed once at production time using a device programmer and cannot be electrically erased, making them a cost-optimized choice for high-volume mature products where firmware is stable. Key features include 192 bytes of data RAM, 33 digital I/O pins, three timers (Timer0, Timer1, Timer2), a USART for asynchronous serial communications, an 8-bit ADC with 8 channels, and a 5-channel 8-bit PWM/capture/compare peripheral. The wide operating voltage range spans 2.5 V to 6.0 V, with a low-power consumption profile of 15 µA typical at 5 V/4 MHz and 1 µA typical at 3 V/32 kHz, supporting commercial, industrial, and extended temperature grades. The PIC16C65A-20/P uses a Harvard architecture with separate program and data buses, enabling simultaneous instruction fetch and operand access. Its fully static design permits operation at any clock frequency down to DC, simplifying low-power sleep/wake designs. On-chip peripherals are mapped into the data memory space and accessed through standard PIC register files, providing deterministic interrupt response. Typical applications include industrial control systems, appliance controllers, automotive body electronics, sensor interface boards, and embedded data acquisition front-ends where the OTP memory cost advantage outweighs the need for in-field firmware updates. Specific fits include HVAC damper controllers, vending machine controllers, and simple motor-driver front-ends. A key design consideration when using PIC16C65A-20/P is firmware provisioning: because OTP memory cannot be erased, code must be 100% validated on a compatible UV-erasable windowed part (PIC16C65A-20/JW) or simulator before committing to the OTP device. Always reserve unused program memory words with explicit goto/end-of-program patterns. This page synthesizes verified distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

Subcategorías

Productos (38.000+)

PIC16C64AT-10I/PQ - 8-Bit PIC MCU 3.5KB OTP 33 I/O | Microchip

PIC16C64AT-20/L - 8-Bit 20MHz OTP MCU, 3.5KB | Microchip

PIC16C64AT-20/PQ - 8-Bit 20MHz OTP MCU 3.5KB | Microchip

PIC16C64AT-20E/PQ - 8-Bit 20MHz OTP MCU, 3.5KB | Microchip

PIC16C64AT-20E/PT - 8-bit OTP MCU, 20MHz, 44-TQFP | Microchip

PIC16C64AT-20I/PQ - 8-Bit 20MHz OTP MCU, 3.5KB | Microchip

PIC16C65A-04/L - 8-bit 4MHz 7KB OTP MCU 44-PLCC | Microchip

PIC16C65A-04/P - 8-Bit 4MHz 7KB OTP MCU 40-PDIP | Microchip

PIC16C65A-04/PQ - 8-Bit 4MHz 7KB OTP MCU 44-MQFP | Microchip

PIC16C65A-04E/L - 8-bit OTP MCU, 7KB EPROM, 33 I/O, 44-PLCC | Microchip

PIC16C65A-04E/P - 4MHz 8-Bit OTP MCU, 7KB EPROM, 40-PDIP | Microchip

PIC16C65A-04E/PQ - 8-bit 4MHz MCU, 7KB OTP, 44-MQFP | Microchip

PIC16C65A-04E/PT - 8-bit PIC MCU 7KB OTP 4MHz 44-TQFP | Microchip

PIC16C65A-04I/P - 8-Bit 4MHz OTP MCU 7KB EPROM | Microchip

PIC16C65A-04I/PQ - 4MHz 8-bit MCU, 7KB OTP, 44-MQFP | Microchip

PIC16C65A-10/L - 8-Bit 10MHz OTP MCU 7KB | Microchip

PIC16C65A-10/P - 8-Bit 10MHz OTP MCU, 7KB Flash | Microchip

PIC16C65A-10/PQ - 8-bit OTP MCU 7KB 33 I/O | Microchip

PIC16C65A-10/PT - 8-bit OTP MCU 7KB 10MHz TQFP-44 | Microchip

PIC16C65A-10E/PQ - 8-Bit CMOS MCU, 7KB OTP, 10MHz | Microchip

PIC16C65A-10I/L - 8-Bit 10MHz OTP MCU 7KB | Microchip

PIC16C65A-10I/PQ - 8-bit RISC MCU, 7KB OTP, 44-MQFP | Microchip

PIC16C65A-10I/PT - 8-Bit 10MHz OTP MCU 7KB Flash 44-TQFP | Microchip

PIC16C65A-20/P - 8-Bit 20MHz 7KB OTP MCU 40-PDIP | Microchip