Circuitos integrados

PIC16C712-20I/SO

PIC16C712-20I/SO - 8-Bit 20MHz OTP MCU 1.75KB | Microchip

The Microchip Technology PIC16C712-20I/SO is an 8-bit CMOS OTP-based microcontroller in the PIC16C family, delivering 20 MHz operation (200 ns instruction cycle) in an 18-pin SOIC package. The device integrates 1.75 KB of One-Time-Programmable program memory (1K x 14 words), 128 bytes of RAM, 13 digital I/O pins, and a 4-channel 8-bit Analog-to-Digital Converter (ADC) along with a Capture/Compare/PWM (CCP) module, two 8-bit timers and one 16-bit timer. An 8-bit microcontroller is a single-chip computer that processes data in 8-bit chunks and integrates a CPU, memory, and peripherals. Within the embedded hierarchy, the PIC16C712 sits at: microcontroller -> embedded microcontroller -> microprocessor-based IC -> semiconductor. The OTP variant uses one-time-programmable EPROM for code storage, which makes it suited to mature, cost-sensitive production runs where code is finalized at the time of manufacture and field reprogramming is not required. The 'I' suffix denotes the industrial temperature grade (-40C to +85C). Key features include a high-performance RISC CPU with only 35 single-word instructions to learn, single-cycle execution for most instructions (two cycles for program branches), and brown-out reset plus power-on reset for robust startup. The 8-bit ADC provides up to 4 input channels, while the CCP module supports capture, compare, and PWM generation for motor, lighting, or signal-conditioning control. The wide operating voltage range of 4.0 V to 6.0 V makes it compatible with both 5 V regulated rails and legacy 5 V systems. Architecturally, the PIC16C712 uses a Harvard-style RISC core with separate program and data buses, enabling simultaneous instruction fetch and operand access. The 8-level deep hardware stack, 7 special-function registers, and direct/indirect addressing modes simplify firmware development in assembly or C (with the MPASM/MPLAB toolchain). Compared to legacy 8051 MCUs, the PIC16C712 delivers higher MIPS-per-mW and a smaller instruction footprint. Typical applications include consumer appliance control, simple sensor interface modules, automotive body electronics (A/D-based sensor monitoring), industrial control timers, and white-goods PWM motor drivers. It is widely used in cost-driven embedded products where OTP is acceptable and where on-chip ADC and CCP reduce external component count. Designed-in products span decades thanks to long-life industrial and appliance markets. When designing with this part, allocate the I/O map carefully because RB4-RB7 share an interrupt-on-change feature. Ensure decoupling per Microchip's recommended 100 nF + 10 uF bulk capacitor placement, and respect the 6.0 V absolute maximum on VDD. Designers migrating to flash-based PIC16F equivalents should verify the CCP and ADC register layouts. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical engineering notes not found in the manufacturer datasheet alone, giving procurement and design engineers a faster sourcing decision.

Cotización Contacto

PIC16C712/JW

PIC16C712/JW - 8-Bit 20MHz OTP MCU with ADC | Microchip

The Microchip Technology PIC16C712/JW is an 8-bit CMOS RISC microcontroller built around the PIC16C architecture, running at up to 20 MHz (200 ns instruction cycle) with 1.75 KB (1K x 14) of UV-erasable EPROM program memory, 128 bytes of RAM, and 128 bytes of EEPROM data memory. It is housed in an 18-pin CERDIP (windowed) through-hole package that allows the program memory to be erased by UV exposure, making the part suitable for prototyping and field-reprogrammable designs rather than high-volume production programming. What is an 8-bit OTP/EPROM microcontroller? It is a single-chip computer integrating a CPU, non-volatile program memory (one-time-programmable or UV-erasable), RAM, and peripherals such as timers and ADCs. Within the power management and embedded hierarchy, microcontrollers sit at the same tier as DSPs and FPGAs, but are optimized for deterministic control tasks at low cost and low power, and they sit below ASICs in design complexity. PIC16C-series parts belong to Microchip's mid-range 14-bit instruction core family, sitting above the baseline PIC12C and PIC16C5X families and below the PIC17C/PIC18C extended families. Key differentiating features include four channels of 8-bit A/D conversion, two 8-bit timers (Timer0 and Timer2) plus one 16-bit timer (Timer1), a capture/compare/PWM (CCP) module, and a watchdog timer. The 18-pin CERDIP with quartz window enables code development cycles that OTP-only packages do not allow. Operating voltage spans 2.5 V to 5.5 V and the commercial temperature grade is 0 C to +70 C, with the part drawing a few mA active and microamps in standby. Architecturally, PIC16C712 uses a Harvard-style 14-bit-wide program memory bus and 8-bit data bus, with a single accumulator (W) and a 36-byte general-purpose register file. The 8-bit ADC uses successive approximation with a sample-and-hold capacitor and selectable reference voltages, while the CCP module supports capture, compare, and 10-bit PWM modes. This combination of timers, ADC and CCP in a small through-hole package makes the device a popular legacy control platform. Typical applications include automotive body controllers, industrial process control loops, white-goods and appliance controllers, sensor signal conditioning, and consumer device front-ends. The windowed CERDIP package is most often used in development and low-volume production where code revisions are expected. Trade-offs to consider are the CERDIP form factor (through-hole only, large footprint) versus modern surface-mount PIC16F equivalents, and the obsolete/legacy lifecycle status versus currently-active flash parts in the same PIC16 family.

Cotización Contacto

PIC16C712T-04E/SO

PIC16C712T-04E/SO - 8-Bit 4MHz OTP MCU 18-SOIC | Microchip

The Microchip Technology PIC16C712T-04E/SO is a CMOS OTP-based 8-bit PIC microcontroller in an 18-pin SOIC wide-body package (Tape & Reel), operating from a single 5V supply at 4 MHz. It integrates 1.75 KB (1K x 14) of One-Time Programmable program memory, 128 bytes of RAM, 13 general-purpose digital I/O pins, and a 4-channel 8-bit Analog-to-Digital converter. What is a PIC 16C microcontroller? PIC 16C refers to Microchip's mid-range 8-bit OTP (One-Time Programmable) microcontroller family using a RISC Harvard architecture. They execute one instruction per cycle (200 ns at 20 MHz) from a fixed 35-instruction set, sit in the hierarchy PIC microcontroller -> 8-bit MCU -> embedded controller -> semiconductor, and historically served low-cost, high-volume consumer and industrial designs before Flash-based PIC16F parts replaced them in new designs. Key features of the PIC16C712T-04E/SO include Brown-out Detect and Power-on Reset for safe startup, a Watchdog Timer for runaway code recovery, a Capture/Compare/PWM (CCP) peripheral, two 8-bit timers plus one 16-bit timer, and a 4-channel 8-bit ADC. The "04" speed grade denotes 4 MHz operation, while the "E" suffix indicates the Extended industrial temperature range (-40C to +125C). The "T" denotes Tape & Reel packaging for high-volume pick-and-place assembly. Architecturally, the device uses a 14-bit wide instruction word with an 8-bit data path, providing 200 ns instruction cycle at 4 MHz (DC to 4 MHz external clock input). The OTP program memory is one-time programmable, requiring a device programmer such as the PICSTART Plus or MPLAB PM3 - field firmware updates are not possible, which is the primary trade-off versus Flash-based PIC16F successors. Typical applications include appliance control, sensor signal conditioning, simple motor drive (via PWM), automotive body electronics, lighting controllers, and battery-powered industrial sensor nodes where the extended temperature grade and 5V tolerance are advantageous. It is also widely used in legacy equipment repair and industrial retrofit designs where exact pin-compatible replacements are required. When designing with this part, note that OTP memory cannot be reprogrammed, so code must be fully verified before commitment. For new designs, the Flash-based PIC16F716-I/SO is generally preferred for in-system reprogrammability, but the PIC16C712T-04E/SO remains valuable for cost-sensitive, high-volume, code-stable applications. This page synthesizes distributor inventory, parametric drop-in equivalents, and design notes that complement the Microchip datasheet. All pricing is referenced as of 2026-09-18.

Cotización Contacto

PIC16C712T-04I/SO

PIC16C712T-04I/SO - 8-Bit 4MHz 1.75KB OTP MCU 18-SOIC | Microchip

The Microchip Technology PIC16C712T-04I/SO is an 8-bit CMOS RISC microcontroller built around the PIC16 architecture, operating at 4 MHz with 1.75 KB (1K x 14) of One-Time Programmable (OTP) program memory and 128 bytes of RAM, housed in a surface-mount 18-pin SOIC (SO) package supplied on tape and reel. The part is a member of the legacy PIC16C71x family and offers 4 channels of 8-bit Analog-to-Digital conversion, a Capture/Compare/PWM (CCP) module, and two additional 8-bit timers beyond the baseline Timer0. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, working RAM, and peripheral interfaces onto one silicon die. In the broader semiconductor hierarchy, the PIC16C712 sits within microcontrollers -> embedded processors -> digital ICs -> semiconductors. The "16C" prefix denotes CMOS OTP technology, where the program memory is written once at production time and is non-erasable, making the device well suited to mature, cost-sensitive, high-volume consumer and industrial products where firmware is stable. Key features include 35 single-word RISC instructions, all single-cycle except two-cycle branches, a 200 ns instruction cycle at 20 MHz maximum clock, an 8-level deep hardware stack, and 13 bidirectional I/O pins with individual direction control. The 4-channel 8-bit A/D converter simplifies sensor-interface designs, while the CCP module enables simple PWM motor and lighting control without external timing circuitry. The industrial (-40C to +85C) temperature range is encoded in the "I" suffix, and the "04" speed grade marks the 4 MHz operating point. Typical applications include appliance control modules, simple sensor interfaces with on-chip ADC, low-cost PWM fan or LED drivers, and replacement of legacy PIC16C5X designs requiring A/D capability. The 18-SOIC package is the most common PCB-friendly footprint in the family and matches the PIC16C711 / PIC16C710 pinout, simplifying layout migration. When designing with this device, note that OTP memory cannot be re-programmed in the field, so firmware must be fully validated before production programming. Consider the flash-based PIC16F716 or PIC16F707 as in-system reprogrammable alternatives for new designs. Always de-couple VDD with a 100 nF ceramic capacitor placed within 5 mm of the pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC16C712T-04I/SS

PIC16C712T-04I/SS - 4MHz 8-Bit OTP MCU, 1.75KB | Microchip

The Microchip Technology PIC16C712T-04I/SS is an 8-bit CMOS OTP (One-Time Programmable) microcontroller from the PIC16C family, operating at 4 MHz with a 200 ns instruction cycle and packaged in a 20-pin SSOP (SS) package with industrial-grade temperature rating. What is a PIC microcontroller? A PIC microcontroller is a family of Harvard-architecture 8/16/32-bit microcontrollers originally developed by Microchip Technology, featuring RISC instruction sets, integrated peripherals (ADC, timers, PWM, communication), and on-chip non-volatile memory. The PIC16C sub-family uses One-Time Programmable EPROM for program storage, which is well-suited to high-volume production where firmware is final and code protection is required. The PIC16C712T-04I/SS sits within this OTP-based 8-bit MCU hierarchy as: 8-bit microcontroller -> RISC MCU -> PIC16C OTP family -> PIC16C7xx series with ADC and PWM. Key features include 1.75 KB of program memory organized as 1K x 14 bits, 128 bytes of data RAM, 13 I/O pins, four 8-bit analog-to-digital converter (ADC) channels, a Capture/Compare/PWM (CCP) module, and integrated peripherals such as Brown-out Detect/Reset, Power-on Reset, and a Watchdog Timer. The 35 single-word RISC instruction set and DC to 4 MHz oscillator range simplify firmware development, while the 20-pin SSOP form factor supports compact surface-mount designs. The PIC16C712 uses a modified Harvard architecture with separate program and data buses, allowing instruction fetch and operand read to occur in the same cycle. The 14-bit wide instruction word provides compact code density, while the 8-bit data path keeps peripheral control straightforward. The integrated 8-bit ADC offers up to four channels with configurable reference voltages, supporting sensor and analog signal conditioning tasks. Typical applications include industrial control subsystems, sensor signal acquisition modules, low-cost consumer appliance controllers, and embedded control boards requiring on-chip ADC plus PWM motor or lighting control. The wide 2.5V to 5.5V supply range and 13 I/O pins provide ample headroom for switches, relays, sensors, and communication interfaces. The OTP memory architecture is intended for production volumes where firmware is fixed and code security is desired. When designing with the PIC16C712T-04I/SS, verify whether OTP or Flash-based memory is appropriate: OTP prevents field firmware updates, so production-grade firmware validation must be complete before programming. For prototype and pre-production work, designers may prefer the Flash-based PIC16F712 equivalent, which supports in-circuit reprogramming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including pin-compatible OTP and Flash PIC16 variants and a comparison table for sourcing decisions.

Cotización Contacto

PIC16C712T-20/SS

PIC16C712T-20/SS - 8-Bit 20MHz OTP MCU, 1.75KB | Microchip

The Microchip Technology PIC16C712T-20/SS is an 8-bit CMOS OTP (One-Time Programmable) RISC microcontroller from the PIC® 16C family, delivering 20 MIPS performance at 20 MHz in a 20-pin SSOP package. It integrates 1.75 KB of program memory (1K x 14) and 128 bytes of RAM, with 4-channel 8-bit Analog-to-Digital conversion, a Capture/Compare/PWM module, and the standard 35-instruction PIC16C core for compact embedded control code. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripheral interfaces onto one die. The PIC16C712 belongs to the PIC® 16C family of 8-bit RISC microcontrollers, which sit within the broader taxonomy of microcontrollers -> embedded processors -> semiconductor ICs. OTP-based PIC MCUs are programmed once via a device programmer and retain their code without external memory, making them ideal for fixed-function commercial and industrial products where flash reprogrammability is not required. Key features include 200 ns instruction execution time, 13 I/O pins, two 8-bit timers plus one 16-bit timer, watchdog timer with on-chip RC oscillator, power-on reset, brown-out detect, and in-circuit serial programming (ICSP) capability. The 8-bit ADC with 4 input channels supports 8-bit resolution suitable for basic sensor monitoring and potentiometer feedback applications. The architecture uses a Harvard-style 14-bit instruction word with separate program and data buses, enabling deterministic single-cycle instruction execution. The 20-pin SSOP footprint is optimized for space-constrained applications where PCB area matters more than wide peripheral count. Typical applications include consumer appliance control, HVAC thermostats, small motor control, battery chargers, security sensor interfaces, and low-cost industrial control modules. The OTP memory model suits high-volume fixed-code products where unit cost dominates over field upgradability. When designing with this device, ensure the 5V supply rail is stable because the OTP version does not support ISP flash reprogramming in-circuit. Plan code carefully before burning the part, and always order production quantities with a margin for code-revision rework. This page synthesizes distributor pricing, drop-in same-family and cross-brand alternatives, and practical design notes that go beyond what is printed in the manufacturer's datasheet.

Cotización Contacto

PIC16C712T-20E/SO

PIC16C712T-20E/SO - 8-Bit 20MHz OTP MCU, 1.75KB | Microchip

The Microchip Technology PIC16C712T-20E/SO is a 8-bit CMOS OTP microcontroller in the PIC16C family, delivering 20MHz (200ns instruction cycle) performance with 1.75KB (1K x 14) of one-time-programmable program memory, 128 bytes of RAM, and 13 general-purpose I/O pins, all housed in an 18-pin SOIC (SO) package with 7.50mm body width. The "T" suffix indicates tape-and-reel packaging, the "20" denotes the 20MHz maximum clock, the "E" designates the extended industrial temperature grade (-40C to +125C), and "/SO" specifies the SOIC-18 surface-mount package. What is an OTP microcontroller? An OTP (One-Time Programmable) microcontroller is a type of embedded computing device whose program memory can be written only once after manufacture, using a programmable ROM cell that is permanently altered (typically by blowing a fuse or antifuse) during device programming. OTP MCUs occupy a middle ground between mask-ROM parts (cheapest at high volume but require factory commitment) and flash-based MCUs (reprogrammable in-circuit but slightly more expensive per unit). They are favored in cost-sensitive, high-volume, mature products where firmware has stabilized and field updates are not required, such as appliance controllers, simple sensor interfaces, and consumer toys. The PIC16C712T-20E/SO integrates a 4-channel 8-bit Analog-to-Digital converter with 2 additional timers (Timer0, Timer1, and Timer2 plus a Capture/Compare/PWM module), enabling mixed-signal embedded designs in a single chip. The 35 single-word instruction RISC architecture simplifies code development, while upward compatibility with PIC16C5X and PIC12CXXX allows firmware migration from older PIC designs. The 18-pin SOIC form factor suits through-hole-free, surface-mount assembly and supports the operating voltage range of 4.0V to 5.5V. Typical applications include appliance control boards, low-cost motor control loops via the CCP module, simple sensor interface front-ends, hobbyist and educational projects, and legacy industrial controller retrofits. The extended temperature range makes the "E" suffix variant suitable for under-hood automotive subsystems and outdoor industrial installations. A key design consideration when selecting an OTP MCU is field-serviceability: once programmed, the device cannot be firmware-updated, so designers must provision programming test pads or sockets in production. Also note that the PIC16C712 series is in mature/legacy status with Microchip, so the PIC16F877A or PIC16F18855 flash-based equivalents are typically preferred for new designs.

Cotización Contacto

PIC16C712T-20E/SS

PIC16C712T-20E/SS - 8-Bit 20MHz OTP MCU, 1.75KB, 20-SSOP | Microchip

The Microchip Technology PIC16C712T-20E/SS is a high-performance RISC-based 8-bit CMOS OTP microcontroller from the PIC16C family, operating at up to 20 MHz with a 200 ns instruction cycle. The device integrates 1.75KB (1K x 14) of One-Time-Programmable program memory, 128 bytes of RAM, 13 digital I/O pins, and a 4-channel 8-bit Analog-to-Digital converter, and is housed in a 20-pin SSOP (Shrink Small Outline Package) tape-and-reel format. Background: An 8-bit microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory (ROM/Flash/OTP), volatile data memory (RAM), and peripheral interfaces. The PIC16C family uses a Harvard RISC architecture that separates program and data buses, enabling single-cycle instruction execution for most opcodes except program branches. OTP memory is programmed once and cannot be erased, making OTP MCUs economical for low-to-medium volume applications where firmware is stable. Key features of the PIC16C712T-20E/SS include 35 single-word instructions, Brown-out Detect/Reset (BOR), Power-on Reset (POR), a Watchdog Timer (WDT), a Capture/Compare/PWM (CCP) module, and an extended -40C to +125C industrial operating temperature range denoted by the "E" suffix. The "T" in the part number indicates tape-and-reel packaging, and "20" specifies the 20 MHz maximum clock speed. The "SS" suffix designates the 20-pin SSOP package. Architecturally, the PIC16C712T uses an enhanced PIC16C5X core with 14-bit instruction words, dual 8-bit timer/counters (Timer0 with 8-bit prescaler, Timer1 with 16-bit operation), and a 4-channel 8-bit ADC with selectable reference voltages. The CCP module supports 10-bit PWM resolution, enabling motor control, LED dimming, and signal generation applications. Typical applications include appliance control, automotive subsystems (non-safety-critical), industrial sensor interfaces, low-end motor control, and white goods. The wide operating temperature range also makes it suitable for outdoor and harsh-environment embedded designs. When designing with this MCU, ensure oscillator selection matches the application's clock-accuracy requirements: external clock mode supports crystal or resonator operation up to 20 MHz, and unused I/O pins should be configured as outputs to minimize power consumption. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing cross-package context and selection guidance for engineers evaluating this part.

Cotización Contacto

PIC16C712T-20I/SO

PIC16C712T-20I/SO - 8-Bit 20MHz OTP MCU 1.75KB | Microchip

The Microchip Technology PIC16C712T-20I/SO is a member of the PIC16C7xx family of 8-bit CMOS microcontrollers built on a RISC architecture, offering 20 MHz maximum operating frequency, 1.75 KB (1K x 14) of One-Time Programmable (OTP) program memory, and 128 bytes of data RAM in an 18-pin SOIC package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (ROM/Flash/OTP), working RAM, and a rich set of peripheral blocks (I/O ports, timers, ADC, communications) onto one die. The PIC16C family uses a Harvard RISC core with a small, deterministic instruction set, allowing most instructions to execute in a single oscillator cycle (4 clocks). Within the broader taxonomy, an 8-bit MCU sits below 16-bit and 32-bit controllers in computational throughput but excels in low cost, low power, and deterministic interrupt response, making it the workhorse of cost-sensitive embedded designs. Key features of the PIC16C712 include an integrated 4-channel, 8-bit Analog-to-Digital Converter (ADC), a 13-bit I/O count across two ports (PORTA and PORTB), a watchdog timer with on-chip RC oscillator, a programmable code-protection mechanism, and an operating voltage range of 2.5 V to 6.0 V (typical 5 V). The 'T' suffix denotes tape-and-reel packaging, '20' indicates the 20 MHz speed grade, and 'I' marks the -40C to +85C industrial temperature range. From an architectural standpoint, the device has a 14-bit instruction word, a 35-instruction set, two 8-bit timer/counters (Timer0, Timer2) plus a 16-bit timer (Timer1), and a 5-channel 8-bit ADC with selectable reference voltages. The 18-pin SOIC package supports through-hole-free assembly and is one of the most widely used footprints for cost-sensitive consumer, industrial, and appliance applications. Typical applications include motor control (small DC and stepper drivers), battery chargers and smart power management, small appliances (coffee makers, hand tools), automotive body controllers (non-safety subsystems), and general-purpose sensor-interface boards. The on-chip ADC allows direct connection to potentiometers, thermistors, and low-bandwidth analog sensors without an external converter. When designing with this part, note that OTP memory cannot be reprogrammed in-circuit; for prototypes choose a windowed (JW) or Flash-based PIC16F equivalent. Also confirm oscillator configuration (RC, XT, HS, LP) matches the crystal or resonator in use, and respect the 20 MHz VDD-dependent limit to avoid timing violations in high-Vdd designs. This page synthesizes distributor pricing, package-level alternatives, and design notes specific to the PIC16C712 SOIC-18 footprint, going beyond the manufacturer datasheet to add selection guidance for engineers evaluating cross-brand 8-bit MCU replacements.

Cotización Contacto

PIC16C712T-20I/SS

PIC16C712T-20I/SS - 8-bit CMOS MCU, 1.75KB OTP, 20MHz | Microchip

The Microchip Technology PIC16C712T-20I/SS is an 8-bit CMOS OTP-based microcontroller built on the PIC16C family architecture, offering 1.75KB of program memory (1K x 14 words), 128 bytes of RAM, and 13 I/O pins in a 20-pin SSOP package. It integrates a 4-channel 8-bit Analog-to-Digital Converter (ADC), a Capture/Compare/PWM (CCP) module, and 2 additional timers, executing instructions in 200ns at 20MHz for deterministic embedded control. A microcontroller (MCU) is a single-chip computer integrating a CPU core, non-volatile program memory, working RAM, and peripherals such as ADCs, timers, and communication interfaces. In the broader system hierarchy, the PIC16C712 belongs to: microcontroller -> embedded controller -> semiconductor IC. Within Microchip's taxonomy, the PIC16C family targets 8-bit mid-range applications, sitting between the smaller PIC12C and the more capable PIC17C/18F families. Key features of the PIC16C712T-20I/SS include a 20MHz operating frequency, 20ns instruction cycle, 128-byte SRAM data memory, 13 digital I/O pins, 4-channel 8-bit ADC, integrated CCP module, two 8-bit timers plus one 16-bit timer, watchdog timer with on-chip oscillator, and In-Circuit Serial Programming (ICSP) capability. The OTP (One-Time Programmable) program memory is suited for mature, cost-sensitive production volumes. Technically, the device uses a RISC Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and operand access. Brown-out Reset, Power-on Reset, and a wide 2.5V-5.5V operating range support reliable operation in industrial environments, while the -40C to +85C industrial temperature grade (the I suffix) enables use in non-automotive harsh environments. Typical applications include appliance control, motor control PWM loops, sensor signal conditioning with on-chip ADC, automotive body electronics (non-safety), industrial automation modules, and white-goods control boards. The integrated ADC and CCP module reduce BOM count in mixed-signal designs. When designing with this part, account for the OTP memory constraint: firmware must be fully validated before programming since it cannot be re-flashed. For field-upgradable designs, choose the flash-based PIC16F712 equivalent instead. This page synthesizes distributor pricing, drop-in compatible variants, and practical design considerations not found in the standalone manufacturer datasheet.

Cotización Contacto

PIC16C715-04/SO

PIC16C715-04/SO - 8-bit 4MHz MCU, 3.5KB OTP, 13 I/O | Microchip

The Microchip Technology PIC16C715-04/SO is an 8-bit RISC microcontroller from the PIC16C71X mid-range family, featuring a 4 MHz maximum clock frequency, 3.5KB (2K x 14) of One-Time-Programmable (OTP) program memory, and 128 bytes of on-chip data RAM, all housed in an 18-pin SOIC (SO) package. The device integrates 4 channels of 8-bit Analog-to-Digital (A/D) conversion, a Timer0 8-bit timer/counter with 8-bit prescaler, and 13 bidirectional I/O lines supporting direct LED drive and basic digital interfacing. Operating from a 4.0V to 5.5V single supply, the PIC16C715-04/SO is built on CMOS technology and includes Brown-out Reset (BOR) circuitry for reliable startup under unstable power conditions. An 8-bit microcontroller is a programmable logic device that executes instructions fetched from on-chip program memory using an internal CPU core, with a data path width of 8 bits. Microcontrollers sit within the broader hierarchy of: microcontroller -> microprocessor with integrated peripherals -> embedded computing IC -> semiconductor device. The PIC16C715 belongs to the mid-range PIC16C family, which uses a 14-bit instruction word and Harvard architecture (separate program and data buses), enabling deterministic instruction timing that simplifies real-time control firmware development. Key differentiating features include integrated 8-bit A/D conversion (4 channels) eliminating the need for external ADC ICs in low-resolution analog signal acquisition, hardware Brown-out Reset that prevents code execution at unsafe VDD levels, and a wide commercial operating temperature range suitable for consumer and industrial environments. The OTP program memory allows low-cost, low-volume programming during development or pilot production runs. Architecturally, the PIC16C715 uses a RISC-style instruction set with most instructions executing in a single instruction cycle (4 clock periods), giving an effective throughput of 1 MIPS at 4 MHz. The integrated ADC, BOR, watchdog timer, and power-on reset reduce external component count and BOM cost for embedded applications. Typical applications include automotive body controllers, industrial appliance controls, consumer white goods, simple sensor signal conditioning with on-chip ADC, HVAC thermostat fan wiring, and low-cost embedded control modules. The combination of on-chip ADC and small SOIC-18 footprint makes it well suited for space-constrained analog sensing designs. When designing with this part, ensure the OSC selection bits match the chosen clock source (RC, XT, LP, HS), and allocate sufficient ADC acquisition time (typically >20 us) by adjusting the A/D clock prescaler. OTP memory cannot be re-programmed; consider the Flash-based PIC16F877A or PIC16F88A for in-application reprogrammability. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC16C715-04E/P

PIC16C715-04E/P - 8-bit CMOS MCU, 4MHz, 3.5KB EPROM | Microchip

The Microchip Technology PIC16C715-04E/P is an 8-bit CMOS RISC microcontroller from the PIC16C7X mid-range family, integrating a 4-channel 8-bit A/D converter, 3.5KB EPROM program memory, and 128 bytes of RAM in an 18-pin PDIP (P) through-hole package. It executes instructions in a 200 ns cycle at 4 MHz oscillator input, supports 35 single-word instructions, and operates from a single 4.0 V to 5.5 V supply. An 8-bit microcontroller is a single-chip computer with an 8-bit data path, ALU, registers, program memory, and integrated peripherals. The PIC16C7X family sits in the PIC mid-range hierarchy - more capable than the baseline PIC16C5X/PIC12CXXX but below the PIC17C/PIC18 enhanced families. The PIC16C715 specifically adds an integrated multi-channel ADC and Brown-out Reset (BOR) circuitry, positioning it as a compact analog-friendly MCU. Key features include 13 bidirectional digital I/O pins with individual direction control, an 8-bit Timer0 with an 8-bit programmable prescaler, 4-channel 8-bit A/D converter, on-chip Brown-out Reset (BOR), Power-on Reset (POR), and a Watchdog Timer (WDT) with its own on-chip RC oscillator. The device is fully static CMOS, OTP-based, and offers upward code compatibility with PIC16C5X and PIC12CXXX devices, easing migration. Architecturally, the PIC16C715 uses a Harvard-style separate program and data bus design with a 14-bit instruction word, two-stack hardware stack (PIC16C71X class), and direct/indirect addressing modes. The internal oscillator support and low-power CMOS design suit battery and line-powered embedded applications. BOR and POR ensure defined startup and brown-out recovery, critical for industrial and automotive-grade embedded designs. Typical applications include industrial sensor signal conditioning, low-cost motor control interfaces, automotive body and sensor electronics, appliance control boards, and embedded measurement instruments. The 18-pin PDIP form factor remains popular for through-hole prototyping, educational platforms, and legacy industrial retrofits where surface-mount is impractical. When designing with this MCU, observe the 5.5 V absolute maximum supply and ensure the EPROM programming voltage is correctly sequenced during in-circuit or in-socket programming. For new designs, Microchip recommends the pin-compatible PIC16F716 (Flash-based successor) as a forward migration path with the same 18-pin DIP footprint but in-system programmability. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical engineering notes not found in a single distributor datasheet tab.

Cotización Contacto

PIC16C715-04E/SO

PIC16C715-04E/SO - 8-bit OTP MCU 4MHz 3.5KB EPROM | Microchip

The Microchip Technology PIC16C715-04E/SO is an 8-bit CMOS RISC OTP microcontroller with an integrated 8-bit multichannel A/D converter, packaged in an 18-pin SOIC (SO) outline rated for the automotive temperature grade. According to the manufacturer datasheet, the device operates at 4 MHz clock speed from a 4.0 V to 5.5 V supply, integrates 3.5 KB (2K x 14) of EPROM program memory and 128 bytes of data RAM, and exposes 13 individually-direction-controlled I/O pins. Brown-out Reset (BOR), an 8-bit Timer0 with 8-bit prescaler, a Watchdog Timer, and a 4-channel 8-bit ADC round out the on-chip peripherals, making it a self-contained compute-and-sense node for embedded products. Background knowledge: an 8-bit microcontroller is a single-chip computer built around an 8-bit data path and a Harvard program/data memory architecture. Within that hierarchy, the PIC16C715 belongs to the PIC16C mid-range family of OTP (one-time-programmable) EPROM-based MCUs, sitting between the PIC16C711 (no ADC variant, but smaller pin-out) and the flash-based PIC16F716 superset recommended by Microchip. OTP EPROM MCUs are typically chosen for low-to-medium volume products where the BOM cost advantage of EPROM outweighs the field-reprogrammability of flash. The '-04E' suffix denotes the 4 MHz speed grade with the extended (-40C to +125C) automotive temperature range, and the '/SO' suffix designates the 18-lead small-outline (SOIC-18) gull-wing surface-mount package. Key features highlight the system's ability to deliver analog sensing plus digital control from a 4-5.5 V rail, with 13 GPIO that can each be tri-stated, an 8-bit ADC with four input channels multiplexed from PORTA, and brown-out detection that holds the part in reset until VDD is stable. The CMOS process plus the RISC core delivers 200 ns single-cycle instruction execution, so an interrupt service routine or ADC polling loop can run inside the headroom of most 1 ms control loops. Power-saving SLEEP mode and a Watchdog Timer with its own on-chip RC oscillator are included, so the part can survive brown-outs and soak out without external supervisor hardware. Technical depth: the device uses a 14-bit-wide instruction word aligned to the 2K-word EPROM array, which yields 3.5 KB of program memory. The 8-bit data bus is separate (Harvard architecture), so instruction fetch and data access occur in parallel, removing fetch stalls common to von-Neumann 8051-class parts. The brown-out trip threshold is internally trimmed to approximately 4.0 V, and the part exits reset only after VDD rises above that level, eliminating the need for an external reset supervisor in many designs. Typical applications include automotive body controllers and sensor interfaces, HVAC damper and valve control, white-goods user-interface boards, industrial sensor-transmitter front-ends, battery-powered instrumentation with sleep/wake duty cycling, and retrofits of older PIC16C71X boards to the wider-temperature grade. The 4-channel ADC combined with 13 GPIO lets one PIC16C715 replace a discrete analog front-end plus a small MCU on a 1-square-inch PCB. Design consideration: the EPROM cell windowless package does not allow in-circuit reprogramming; firmware is locked at the time of program and cannot be field-updated. Engineers who anticipate firmware revisions should instead migrate to the pin-compatible flash part PIC16F716 (recommended by Microchip) or, where automotive-grade is required, to PIC16F716-I/SO. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC16C715-04I/P

PIC16C715-04I/P - 4MHz 8-bit CMOS MCU 3.5KB OTP 18-PDIP | Microchip

The Microchip Technology PIC16C715-04I/P is an 8-bit CMOS OTP-based microcontroller in the PIC16C7X mid-range family, housed in a 18-pin PDIP (P) package and operating from 4V to 5.5V with a 4MHz oscillator. It integrates 3.5KB (2K x 14) of one-time-programmable program memory, 128 bytes of RAM, 13 digital I/O pins, and a 4-channel 8-bit analog-to-digital converter. What is an 8-bit microcontroller? An 8-bit MCU is a single-chip computer with an 8-bit data path that executes one instruction per cycle and integrates CPU, RAM, non-volatile program memory, and peripherals. The PIC16C715 belongs to the mid-range PIC16C family and inherits the RISC-based PIC architecture, executing instructions in 200ns at 4MHz. As an OTP part, it is intended for volume production where field firmware updates are not required. Key features include 35 single-word instructions, 8-bit timer/counter with 8-bit prescaler, 4-channel 8-bit ADC, brown-out reset (BOR), power-on reset (POR), and a watchdog timer (WDT). The 13 I/O pins each have individually programmable direction control, and the device supports in-circuit serial programming via the ICSP interface. The PIC architecture is upwards compatible with the PIC16C5X baseline and PIC12CXXX devices, simplifying code migration across the family. The PIC16C715 is built on a CMOS process and operates over the industrial temperature range of -40C to +85C as indicated by the /I designator. It is recommended by Microchip as a legacy successor part for designs previously using the PIC16C71X series; the newer flash-based PIC16F716 is suggested as an upgrade path for new designs. Typical applications include industrial control nodes, appliance controllers, automotive body electronics (where OTP cost advantage matters), consumer products with simple A/D sensing, and educational or hobby microcontroller projects. The 4-channel ADC enables direct interfacing with analog sensors (temperature, light, potentiometers). Designers should consider the OTP limitation (no field re-programming) and plan to use PIC16F716-I/P or similar flash parts if firmware iteration is required. The 18-PDIP package remains a strong choice for through-hole prototyping, breadboarding, and educational kits because it is easy to handle and socket-compatible with most PIC16C71X variants. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16C71X family, and design notes that extend the manufacturer datasheet with practical selection guidance for replacement and migration scenarios.

Cotización Contacto

PIC16C715-20/P

PIC16C715-20/P - 8-bit OTP MCU, 20MHz, 3.5KB, 13 I/O, A/D | Microchip

The Microchip PIC16C715-20/P is a low-cost, high-performance, fully-static, 8-bit CMOS microcontroller from the PIC16CXX mid-range family, integrating a 4-channel 8-bit Analog-to-Digital converter and packaged in an 18-pin PDIP (through-hole). It executes instructions in 200 ns at a 20 MHz oscillator, programs with only 35 single-word instructions, and is built on Microchip's advanced RISC architecture with an eight-level deep hardware stack and multiple internal/external interrupt sources. The OTP program memory holds 3.5 KB (2K x 14 words), the data SRAM is 128 bytes, and 13 digital I/O pins are available for general-purpose use. An 8-bit microcontroller is a single-chip computer that integrates a CPU, memory (ROM/RAM), and peripherals onto one die; the PIC mid-range family extends this concept with a RISC Harvard architecture where program and data buses are physically separated, allowing simultaneous instruction fetch plus data access for deterministic, predictable execution. PIC microcontrollers remain a foundational part of the broader 8-bit MCU market (a sub-category of microcontrollers, which themselves belong to integrated circuits / embedded computing) and are widely deployed in cost-sensitive embedded applications. Key features of the PIC16C715-20/P include 4 channels of 8-bit A/D conversion (making it ideal for sensor reading applications), a 20 MHz maximum operating frequency, 8-bit data path width, on-chip oscillator support (with optional external crystal/resonator), and a wide operating voltage range supporting both 3.0V and 5.0V system designs. The integrated A/D converter eliminates the need for external ADC chips in many designs, reducing BOM cost and PCB footprint. Architecturally, the PIC16C715 employs a 14-bit instruction word with separate program and data buses (Harvard architecture), enabling most instructions to execute in a single instruction cycle. The 8-level deep hardware stack supports nested subroutine calls without software overhead. This OTP-based device is one-time programmable, meaning program memory cannot be erased electrically - making it suitable for production volumes but less ideal for prototyping compared to flash-based PIC16F series. Typical applications include industrial control systems, appliance controllers, automotive sensor interfaces, consumer electronics, low-cost data acquisition systems, and battery-powered instruments. The integrated A/D makes it particularly suited for any application needing analog signal measurement alongside digital I/O control. When designing with the PIC16C715-20/P, remember that it is OTP memory - firmware is permanently written at production time and cannot be updated in the field. For designs requiring in-field reprogrammability or prototype iteration, Microchip recommends migrating to the flash-based PIC16F716, which offers similar peripherals and pin compatibility while supporting hundreds of erase/write cycles. This page synthesizes distributor pricing, drop-in alternatives, lifecycle data, and practical design notes not found in the standalone manufacturer datasheet.

Cotización Contacto

PIC16C715-20/SO

PIC16C715-20/SO - 8-Bit 20MHz OTP MCU 3.5KB 18-SOIC | Microchip

The Microchip Technology PIC16C715-20/SO is an 8-bit CMOS OTP (One-Time Programmable) microcontroller from the PIC16C7X mid-range family, operating at up to 20MHz with 200ns instruction execution, packaged in an 18-pin SOIC (0.295", 7.50mm width) with 3.5KB (2K x 14) of program memory and 128 bytes of RAM, and featuring an integrated 4-channel 8-bit Analog-to-Digital converter. Background - what is an OTP microcontroller? An OTP (One-Time Programmable) microcontroller is a non-erasable variant of flash/EPROM-based MCUs that is programmed once at production or in-system and cannot be reprogrammed. OTP parts are commonly used where cost-sensitive, high-volume consumer or industrial applications do not require firmware updates. They sit within the broader category of 8-bit microcontrollers (8-bit MCU -> microcontroller -> embedded processor -> semiconductor), and the PIC16C715 belongs to Microchip's PIC16 mid-range architecture that uses a 14-bit instruction word and 35 single-word instructions. Key features include a 13-bit I/O count, four 8-bit A/D input channels for direct sensor interfacing, low-power CMOS static design with a commercial 0C to +70C operating range, watchdog timer, power-on reset, and a programmable code-protection mechanism. The RISC architecture delivers deterministic interrupt response and predictable cycle counts - essential for real-time control loops. The PIC16C715 architecture combines a Harvard bus with separate program and data paths, allowing the 14-bit instruction fetch and 8-bit data read/write to occur in the same cycle. The 8-bit ADC includes its own sample-and-hold, and the device is upwards compatible with PIC16C5X and PIC12CXXX for code portability. With the '-20' speed grade, the oscillator supports up 20MHz, providing roughly 5 MIPS throughput. Typical applications include appliance control boards, simple sensor interfaces that need on-chip ADC, low-cost consumer products, automotive body modules (legacy), industrial timers and counters, and remote-control transmitters. The integrated ADC removes the need for an external analog front end in cost-sensitive designs. When designing with this device, note that the PIC16C715 is OTP and cannot be firmware-updated in the field - use PIC16F716 or PIC16F716-I/SO for flash-based equivalents. Commercial grade (0C to +70C) limits deployment in extended-temperature environments; consider PIC16C715-20I/SO for industrial -40C to +85C. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in a single datasheet reference, helping procurement and embedded engineers evaluate the part in context.

Cotización Contacto

PIC16C715-20E/P

PIC16C715-20E/P - 8-bit CMOS MCU 3.5KB OTP 4ch ADC DIP-18

The Microchip Technology PIC16C715-20E/P is an 8-bit CMOS OTP-based microcontroller built on the PIC16 RISC architecture, featuring 3.5KB of EPROM program memory, 128 bytes of RAM, and a 4-channel 8-bit analog-to-digital converter, housed in an 18-pin plastic DIP (PDIP) package. It executes instructions in 200 ns (5 MIPS at 20 MHz oscillator) using only 35 single-word instructions, providing an excellent balance of code density and execution speed for embedded control applications. An 8-bit OTP microcontroller is a single-chip computer with one-time-programmable non-volatile program memory that can be written exactly once, after which the code becomes permanent. The PIC16 family belongs to the broader PICmicro taxonomy (8-bit MCU -> RISC MCU -> microcontroller -> embedded IC), and is fully upwards compatible with the PIC16C5X baseline and PIC12CXXX 8-pin families, allowing code and toolchain reuse across product lines. Key features include 13 individually direction-controlled digital I/O pins, an 8-bit Timer0 with 8-bit prescaler, brown-out reset (BOR) circuitry for safe power-up, a watchdog timer, and four multiplexed ADC channels with 8-bit resolution. The wide 4.0V to 5.5V supply range targets legacy 5V-only designs, while the integrated ADC eliminates an external converter in cost-sensitive analog sensing applications. Internally, the PIC16C715 uses a Harvard architecture with separate program and data buses, allowing instruction fetch and operand access to occur in the same cycle. The 14-bit wide instruction word and RISC engine deliver deterministic 200 ns instruction timing, simplifying real-time control loops. The -20E speed grade guarantees 20 MHz operation across the -40C to +125C extended industrial temperature range, making the part suitable for harsh-environment automotive, appliance, and industrial control boards. Typical applications include automotive sensor interfacing, white-goods and small-appliance controllers, simple industrial automation nodes, and consumer products requiring on-board analog signal acquisition. The 4-channel ADC supports direct connection to thermistors, potentiometers, and low-bandwidth analog sensors without external signal conditioning. When designing with this part, note that the EPROM windowless package is intended for production use only; for prototype development, use the PIC16C715/JW ceramic windowed package for UV-eraseable parts, or migrate to the flash-based PIC16F716 for reprogrammability. Always include proper decoupling (100 nF + 10 uF) within 5 mm of the VDD pin to suppress switching transients during EPROM programming. This page synthesizes verified distributor pricing, drop-in DIP-18 alternatives drawn from the Site MPN cross-reference list, and practical design notes that go beyond the manufacturer datasheet for engineers evaluating long-term sourcing of PIC16C7x legacy designs.

Cotización Contacto

PIC16C715-20E/SS

PIC16C715-20E/SS - 8-bit CMOS MCU, 20MHz, 3.5KB OTP, 20-SSOP

The Microchip PIC16C715-20E/SS is an 8-bit CMOS OTP microcontroller from the PIC16C7X mid-range family, delivering 20MHz core operation, 3.5KB (2K x 14) of One-Time-Programmable program memory, and 128 bytes of RAM in a 20-pin SSOP package. It integrates a 4-channel 8-bit Analog-to-Digital converter with Brown-out Reset (BOR), a Timer0 8-bit timer/counter with 8-bit prescaler, and 13 bidirectional I/O pins with individual direction control, optimized for cost-sensitive embedded applications requiring on-chip analog acquisition. A microcontroller (MCU) is a single-chip computer containing a CPU, memory, and programmable I/O peripherals. The PIC16C715 belongs to the PIC16CXX mid-range architecture family, positioned between the baseline PIC16C5X and the enhanced PIC17CXX. The 8-bit core executes one instruction every 200ns at 20MHz, with only 35 single-word instructions to learn, making this MCU category the foundational tier in the broader microcontroller hierarchy: microcontroller -> embedded processor -> semiconductor IC. Key features include 4 ADC input channels with 8-bit resolution, 13 I/O pins supporting individual TRIS direction control, hardware Brown-out Reset for reliable supply-voltage monitoring, and an extended operating temperature range of -40°C to +125°C. The /E suffix denotes the extended temperature grade, while /SS indicates the 20-pin Shrink Small Outline Package (5.3mm body width) for compact surface-mount designs. The PIC16C715 employs a Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and data access. The 14-bit wide instruction word improves code density compared with 12-bit baseline PIC cores, and the CMOS static design enables full stop/oscillator operation with minimal current draw. On-chip RC oscillator support and a wide 4.0V–5.5V supply range simplify power-tree design. Typical applications include industrial sensor conditioning front-ends, consumer appliance control boards, automotive body modules (non-safety), HVAC thermostat controllers, and battery-powered instrumentation. The integrated ADC reduces external component count where 8-bit conversion accuracy is sufficient. When designing with this device, note that Microchip recommends PIC16F716 as a newer flash-based replacement with equivalent peripherals and pinout; migration from the OTP PIC16C715 to the flash PIC16F716 allows in-circuit reprogramming while preserving the development toolchain investment. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC16C715-20I/SO

PIC16C715-20I/SO - 8-bit 20MHz OTP MCU, 3.5KB, 13 I/O | Microchip

The Microchip Technology PIC16C715-20I/SO is an 8-bit CMOS OTP-based microcontroller from the PIC16CXX mid-range family, operating at up to 20MHz (200 ns instruction cycle) and housed in an 18-pin SOIC (SO) package with industrial temperature grade (-40C to +85C). It integrates 3.5KB of OTP program memory (2K x 14 words), 128 bytes of RAM, 13 general-purpose I/O pins, and a 4-channel 8-bit analog-to-digital converter with brown-out reset (BOR) and a Timer0 8-bit timer/counter with 8-bit prescaler. An OTP microcontroller is a one-time-programmable device - the on-chip program memory can be written exactly once using a device programmer, after which the code is permanent. This makes OTP MCUs a cost-optimized choice for high-volume, code-stable embedded products where field firmware updates are not required. The PIC16C715 belongs to the broader microcontroller (MCU) hierarchy: MCU -> embedded controller -> 8-bit microcontroller -> CMOS mid-range MCU. Its PIC16CXX mid-range core delivers deterministic execution with only 35 single-word instructions, easing code generation in assembly or C (MPLAB XC8). Key features include 4 channels of 8-bit A/D conversion for sensor interfacing, 13 I/O pins with individually programmable direction, an internal oscillator option to reduce external component count, brown-out reset for reliable power-on behavior, and a wide 4.0V to 5.5V supply range. The device supports in-circuit serial programming (ICSP) via two pins, allowing factory programming even after board assembly. The PIC16C715 uses a Harvard architecture with separate program and data buses, achieving a 200 ns instruction cycle at 20MHz. The 8-bit ALU, working register (W), and 7 special-function registers handle arithmetic, logical, and bit-manipulation operations. The integrated A/D converter uses successive approximation with 4 multiplexed input channels, suitable for sensor signal digitization. Typical applications include appliance control modules, automotive sensor interfaces, industrial process monitoring, consumer electronics with fixed firmware, and low-cost data acquisition front-ends. Its combination of integrated ADC, BOR, and small SOIC footprint makes it well suited for compact PCB designs. When designing, reserve the MCLR pin for either an external reset network or ICSP. Use 0.1uF decoupling close to VDD and a bulk capacitor at the supply pin. The A/D reference selection (VDD or external) directly determines conversion accuracy, so layout the analog pins away from digital switching traces. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC16C715/JW

PIC16C715/JW - 8-Bit 20MHz MCU, 3.5KB EPROM, 18-CERDIP Window | Microchip

The Microchip Technology PIC16C715/JW is an 8-bit CMOS RISC microcontroller in an 18-pin CERDIP windowed package, featuring 20MHz maximum clock speed, 3.5KB (2K x 14) of one-time-programmable (OTP) EPROM program memory, and 128 bytes of RAM. It operates from a 4V to 5.5V supply and integrates 4 channels of 8-bit Analog-to-Digital converter, 13 I/O pins, and an external oscillator interface, all in a UV-erasable CERDIP form factor intended for through-hole prototyping. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and configurable peripherals on one die. Within the broader taxonomy, the PIC16C715 belongs to the 8-bit microcontroller family, specifically Microchip's mid-range PIC16C architecture (PIC16 -> PIC16C -> PIC16C7xx), itself a branch of the PIC RISC family of microcontrollers and finally a category of embedded processors / semiconductors. Engineers choose OTP-EPROM PIC MCUs for low-volume production runs where in-system reprogrammability is not required but a known-good code pattern has been validated. Key features include 4 channels of 8-bit A/D conversion (suitable for sensor interfaces in automotive, industrial, appliance, and consumer products), 13 digital I/O pins, a 20MHz oscillator input that yields 200ns instruction execution, and only 35 single-word instructions to learn. The CERDIP window package allows UV erasure during development, which is uncommon in modern MCU packages and signals the part's heritage as a development-friendly variant within the PIC16C7xx line. The PIC16C715 core is a Harvard-architecture RISC CPU with separate program and data buses, supporting a 14-bit instruction word and an 8-bit data path. It executes one instruction per internal clock cycle (four oscillator clocks) and provides a hardware interrupt controller, watchdog timer, and power-on reset. The 8-bit A/D converter uses successive-approximation register (SAR) topology with analog input multiplexing across four channels. Typical applications include automotive sensor interfaces, industrial control, consumer appliance controllers, and low-cost embedded products requiring analog input. The wide 4V-5.5V range and 13 I/O pins make it well suited to motor-control front ends and user-interface panels with mixed analog/digital signals. When designing with the PIC16C715, ensure your toolchain is configured for the PIC16C7xx device family and use Microchip's MPASM assembler or C compilers with the appropriate header file. The /JW windowed package is intended for engineering development; for production, switch to a one-time-programmable PDIP or windowless CERDIP variant. This page synthesizes distributor pricing, drop-in alternatives from Microchip's PIC16C family and competing 8-bit MCU lines, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC16C715T-04/SO

PIC16C715T-04/SO - 8-Bit 4MHz OTP MCU 3.5KB | Microchip

The Microchip Technology PIC16C715T-04/SO is an 8-bit PIC16-series CMOS microcontroller built around a RISC core with 35 single-word instructions and 200 ns instruction execution time, packaged in a 18-lead SOIC (SO) with Tape & Reel packaging. The device integrates 3.5 KB of One-Time-Programmable (OTP) program memory organized as 2K × 14 words and 128 bytes of data RAM, runs at a maximum clock frequency of 4 MHz, and operates from a 5 V supply typical of mid-range PIC microcontrollers. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral interfaces such as timers, I/O ports, and analog-to-digital converters into one package. Within the broader taxonomy, the PIC16C715 belongs to the PIC16 mid-range family of 8-bit microcontrollers, which sits under the PIC16C OTP/EPROM-based sub-family and ultimately under Microchip's 8-bit PIC architecture — a category commonly placed under embedded microcontrollers and then under Integrated Circuits. The PIC16C715 specifically integrates a 10-bit (approximate) ADC and 13 digital I/O pins, making it suitable for mixed-signal embedded designs. Key features include low-power CMOS technology, an integrated 8-bit ADC, 13 digital I/O lines, two timer modules (TMR0 and TMR1-style counters referenced in mid-range PICs), a watchdog timer, and the standard PIC16 in-system programming/serial programming interface. The 4 MHz maximum oscillator frequency and 35-instruction RISC core yield predictable deterministic interrupt latency that embedded engineers rely on for real-time control. Architecturally, the part uses a Harvard-style memory map with separate program and data buses, a 14-bit wide instruction word, and a file-register map split between General Purpose Registers (GPR) and Special Function Registers (SFR). The OTP program memory allows one-time customization during manufacturing or engineering bring-up, while the SRAM data memory retains run-time state. Typical applications include appliance control, sensor signal conditioning with on-chip ADC, low-cost consumer electronics, automotive body controllers, and industrial automation sub-systems where a compact 18-pin footprint, a 4 MHz clock, and an integrated analog front-end reduce BOM cost. The 18-SOIC package supports automated SMT assembly in volume production. When designing with this device, observe the 4 MHz oscillator ceiling and ensure decoupling on VDD/VSS. Note that the OTP memory cannot be re-programmed, so firmware must be fully validated before commit. Per Microchip's product page, the newer flash-based PIC16F716 is recommended for new designs. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes not found in a single source on the manufacturer datasheet.

Cotización Contacto

PIC16C715T-04/SS

PIC16C715T-04/SS - 4MHz 8-bit CMOS OTP MCU w/ ADC | Microchip

The Microchip Technology PIC16C715T-04/SS is a CMOS, fully-static, 8-bit RISC microcontroller based on One-Time-Programmable (OTP) EPROM with 3.5KB of program memory (2K x 14 words), 128 bytes of data RAM, and an integrated 4-channel 8-bit analog-to-digital converter. The part operates from a 5V supply (commercial temperature grade 0C to +70C) at a maximum clock frequency of 4 MHz, delivering 200 ns instruction execution time, and is housed in a 20-pin SSOP (209 mil / 5.30 mm body width) package supplied on Tape and Reel. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, and peripherals into one package. PIC microcontrollers use a Harvard RISC architecture with a small, fixed instruction set - the PIC16C715 belongs to Microchip's mid-range PIC16CXX family with 35 single-word instructions, making it easy to program in assembly or C. The 'C' in PIC16C715 indicates One-Time-Programmable EPROM program memory, intended for low-volume production and prototyping. Key features include 13 digital I/O pins, 4 channels of 8-bit ADC, a 14-bit wide instruction word, and two 8-bit timers plus one 16-bit timer (TMR1). The 4 MHz oscillator input combined with the 4-clock-per-instruction cycle yields a 1 MHz instruction rate, and the integrated ADC simplifies sensor-interface designs by eliminating an external converter IC. The architecture is fully static, allowing the clock to be stopped without loss of internal state - a useful trait for low-power wait modes. The mid-range 14-bit core is upward-compatible with the PIC16C5X baseline and PIC12CXXX 8-pin devices, so code written for related parts can be ported with minimal changes. According to the Microchip datasheet, the device supports both RC and crystal oscillator modes. Typical applications include appliance control, low-cost sensor signal conditioning, battery chargers, and any 5V embedded design that needs on-chip ADC without the recurring cost of flash. Note that Microchip recommends the newer PIC16F716 as a flash-reprogrammable migration path for new designs. For designs still using this OTP part, plan the program code carefully before programming - OTP devices cannot be erased. Use an emulator or windowed sample (PIC16C715JW) for prototype development. This page synthesizes distributor pricing, drop-in alternatives within the PIC16C71X family, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC16C715T-04I/SO

PIC16C715T-04I/SO - 8-Bit PIC MCU, 4MHz, 3.5KB OTP, 18-SOIC

The Microchip Technology PIC16C715T-04I/SO is an 8-bit CMOS OTP-based microcontroller in the PIC16C mid-range family, delivering 4 MIPS performance at 4 MHz maximum clock and packaged in an 18-pin SOIC (SO) on tape-and-reel. It integrates 3.5 KB (2K x 14) of One-Time-Programmable program memory, 128 bytes of data RAM, 13 digital I/O pins, four 8-bit analog-to-digital converter channels, and a single 8-bit timer/counter. A microcontroller (MCU) is a single-chip computer that combines a CPU, program memory, data RAM, peripherals, and I/O on one die; the PIC16C715 sits in the legacy "C" OTP generation between the original PIC16C5X baseline and the modern flash-based PIC16F series, designed for high-volume, cost-sensitive embedded control where code is finalized at production and reprogramming is not required. The PIC16C715 family remains pin-compatible and instruction-set compatible with the PIC16C71X group, supporting assembler and C development under MPLAB and the XC8 compiler. Key specifications include a 200 ns instruction cycle, a wide 3.0 V to 5.5 V operating range, an industrial -40 °C to +85 °C temperature grade, and the proprietary PIC RISC architecture with only 35 single-word instructions. The 13 I/O pins can source/sink up to 25 mA for direct LED drive, and the 4-channel 8-bit ADC simplifies sensor-interface designs without external converter ICs. The PIC16C715 uses a Harvard-class architecture with separate program and data buses, a hardware accumulator-based ALU, and an integrated 8-bit successive-approximation ADC. Its OTP EPROM cell provides one-time field or factory programmability at lower mask cost than ROM, making the part attractive for mid-volume production runs where unit pricing matters more than in-system re-programmability. Typical applications include appliance control, sensor signal conditioning, low-cost motor drive, simple LED display drivers, and battery-powered instrumentation. Microchip explicitly recommends the flash-based PIC16F716 as the recommended migration path for new designs and for designs requiring in-system reprogramming. When laying out the PCB, place a 0.1 µF decoupling capacitor as close as possible to VDD, reserve the MCLR pin for a proper reset circuit (do not leave floating), and configure the ADC inputs with adequate trace guarding if the digital switching currents are large. The 04 speed grade denotes 4 MHz operation; the 20 MHz equivalent is the PIC16C715T-20I/SO. This page synthesizes distributor pricing, drop-in same-package alternatives, application recommendations, and design notes not consolidated on any single distributor page, giving engineers a single reference for sourcing, replacement, and design-in decisions for the legacy PIC16C715T-04I/SO.

Cotización Contacto

PIC16C715T-04I/SS

PIC16C715T-04I/SS - 8-Bit PIC MCU, 3.5KB OTP, 4MHz, 20-SSOP

The Microchip PIC16C715T-04I/SS is a CMOS, fully-static, 8-bit PIC microcontroller from the PIC16C71X family, supplied in a 20-pin SSOP (Shrink Small Outline Package) on tape-and-reel. The "T" suffix denotes tape-and-reel packaging, "04" indicates a 4 MHz maximum oscillator frequency, "I" denotes the industrial temperature range (-40C to +85C), and "/SS" specifies the SSOP package. The device integrates 3.5 KB of one-time-programmable (OTP) program memory, 128 bytes of data RAM, 13 digital I/O pins, and a 4-channel 8-bit analog-to-digital converter (ADC), making it suitable for mixed-signal embedded applications. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, program memory (ROM/EPROM/Flash/OTP), working RAM, and peripherals such as timers, ADC, and I/O ports. The PIC16C71X family belongs to Microchip's mid-range PIC architecture (14-bit instruction word), sitting above the baseline PIC16C5X in instruction set power and below the PIC18 family in performance. This hierarchy (OTP-based 8-bit MCU -> PIC mid-range -> 8-bit microcontroller family -> embedded MCU category) makes the PIC16C715 a workhorse for cost-sensitive, low-power control applications. Key features include 200 ns instruction execution time (5 MIPS at 4 MHz), 35 single-word instructions, an 8-level deep hardware stack, four interrupt sources, and a programmable code-protection bit. The 8-bit ADC delivers 4 channels with selectable reference voltages, supporting sensor and signal-acquisition tasks. The CMOS process delivers low power consumption suitable for battery-operated and industrial embedded designs. Architecturally, the device uses a Harvard bus architecture with separate program and data paths, enabling simultaneous instruction fetch and operand access. The RISC-style 35-instruction set simplifies code development while supporting bit-level manipulation, a hallmark of PIC microcontrollers. Two 8-bit timer/counters and one 16-bit timer/counter provide flexible event timing, while the watchdog timer enhances system reliability. Typical applications include sensor signal conditioning, simple motor control, white goods and appliance control, industrial automation peripherals, and battery-powered instrumentation. The industrial temperature range and integrated ADC make it well suited for harsh-environment embedded systems. When designing with this device, note that OTP program memory requires one-time programming during manufacturing and cannot be field-updated; for prototype or low-volume production, consider the flash-based PIC16F716 equivalent recommended by Microchip. Brown-out reset, power-on reset, and watchdog timer features must be configured by firmware for robust operation. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16C71X family, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

Subcategorías

Productos (38.000+)

PIC16C712-20I/SO - 8-Bit 20MHz OTP MCU 1.75KB | Microchip

PIC16C712/JW - 8-Bit 20MHz OTP MCU with ADC | Microchip

PIC16C712T-04E/SO - 8-Bit 4MHz OTP MCU 18-SOIC | Microchip

PIC16C712T-04I/SO - 8-Bit 4MHz 1.75KB OTP MCU 18-SOIC | Microchip

PIC16C712T-04I/SS - 4MHz 8-Bit OTP MCU, 1.75KB | Microchip

PIC16C712T-20/SS - 8-Bit 20MHz OTP MCU, 1.75KB | Microchip

PIC16C712T-20E/SO - 8-Bit 20MHz OTP MCU, 1.75KB | Microchip

PIC16C712T-20E/SS - 8-Bit 20MHz OTP MCU, 1.75KB, 20-SSOP | Microchip

PIC16C712T-20I/SO - 8-Bit 20MHz OTP MCU 1.75KB | Microchip

PIC16C712T-20I/SS - 8-bit CMOS MCU, 1.75KB OTP, 20MHz | Microchip

PIC16C715-04/SO - 8-bit 4MHz MCU, 3.5KB OTP, 13 I/O | Microchip

PIC16C715-04E/P - 8-bit CMOS MCU, 4MHz, 3.5KB EPROM | Microchip

PIC16C715-04E/SO - 8-bit OTP MCU 4MHz 3.5KB EPROM | Microchip

PIC16C715-04I/P - 4MHz 8-bit CMOS MCU 3.5KB OTP 18-PDIP | Microchip

PIC16C715-20/P - 8-bit OTP MCU, 20MHz, 3.5KB, 13 I/O, A/D | Microchip

PIC16C715-20/SO - 8-Bit 20MHz OTP MCU 3.5KB 18-SOIC | Microchip

PIC16C715-20E/P - 8-bit CMOS MCU 3.5KB OTP 4ch ADC DIP-18

PIC16C715-20E/SS - 8-bit CMOS MCU, 20MHz, 3.5KB OTP, 20-SSOP

PIC16C715-20I/SO - 8-bit 20MHz OTP MCU, 3.5KB, 13 I/O | Microchip

PIC16C715/JW - 8-Bit 20MHz MCU, 3.5KB EPROM, 18-CERDIP Window | Microchip

PIC16C715T-04/SO - 8-Bit 4MHz OTP MCU 3.5KB | Microchip

PIC16C715T-04/SS - 4MHz 8-bit CMOS OTP MCU w/ ADC | Microchip

PIC16C715T-04I/SO - 8-Bit PIC MCU, 4MHz, 3.5KB OTP, 18-SOIC

PIC16C715T-04I/SS - 8-Bit PIC MCU, 3.5KB OTP, 4MHz, 20-SSOP