Circuitos integrados

PIC16F15276-I/PT

PIC16F15276-I/PT - 28KB Flash 8-bit MCU, 32MHz, 44-TQFP | Microchip

The Microchip Technology PIC16F15276-I/PT is a 28KB Flash 8-bit PIC microcontroller built on an enhanced mid-range RISC core with a 32 MHz maximum CPU clock, housed in a 44-pin TQFP (10x10 mm) package. It integrates 28KB of Flash program memory, 2KB of SRAM, hardware Core Independent Peripherals (CIPs), Intelligent Analog, and standard communication peripherals for cost-sensitive sensor and real-time control designs. An 8-bit PIC microcontroller is a single-chip CMOS device that combines an 8-bit CPU core, Flash program memory, SRAM, and on-chip peripherals in one package. The PIC16F152xx family occupies a specific tier in the Microchip hierarchy: 8-bit microcontroller -> PIC16 mid-range family -> PIC16F152xx sub-family -> eXtreme Low-Power (XLP) lineup. Its role in a system is to provide deterministic real-time control and sensor I/O with low active and sleep currents, sitting below 16-bit dsPIC and 32-bit SAM devices in computational capability but above simple timer/logic ICs in integration. Key features include 32 MHz maximum operation, 1.8V minimum supply for full-speed analog operation at 16 MHz, hardware 10-bit ADC, two PWM modules, two CCP modules, EUSART, SPI, I2C, Peripheral Pin Select (PPS), Hardware Limit Timer (HLT), Watchdog Timer, and XLP eXtreme Low-Power modes. The 36 programmable I/O lines and 44-pin TQFP footprint make this device well suited to mid-density IoT nodes, sensor hubs, and small industrial control boards. The architecture uses Microchip's enhanced mid-range core with a 16-level hardware stack and a 31-level software-managed stack extension. The integrated 10-bit ADC with internal reference, op amps, and comparators deliver Intelligent Analog, while CIPs such as the CWG (Complementary Waveform Generator) and HLT offload timing-critical functions from the CPU for deterministic, low-jitter response. Typical applications include low-power IoT sensor nodes, battery-powered remote controls, industrial sensor signal conditioning, home appliances, lighting control, and small motor/PWM control. The XLP nanoWatt sleep modes and 1.8V minimum supply make it especially attractive for energy-harvesting designs that must wake, sample, transmit, and return to deep sleep. When designing with this part, place decoupling capacitors within 3 mm of each VDD pin and keep analog traces short and guarded for ADC accuracy. PPS allows pin reassignment after PCB layout is complete, reducing iteration cost during hardware bring-up. This page synthesizes distributor pricing, drop-in alternatives drawn from the PIC16F152xx/153xx family, and practical design notes not collected in a single section of the manufacturer datasheet.

Cotización Contacto

PIC16F1527T-I/PT

PIC16F1527T-I/PT - 8-bit 20MHz MCU 28KB Flash 64-TQFP | Microchip

The Microchip Technology PIC16F1527T-I/PT is an 8-bit PIC16 family microcontroller built on Microchip's enhanced mid-range core, delivering 20 MHz CPU performance (200 ns instruction cycle) with 28 KB of self-programmable Flash program memory and 1.5 KB of SRAM in a 64-pin TQFP (PT) package supplied on tape and reel. Headline parameters include 28 KB Flash (16K x 14 words), 1.5 KB RAM, 256 B EEPROM, 20 MHz maximum clock, and a 1.8 V to 5.5 V wide operating voltage range. The device belongs to the PIC16F152x family which integrates 12-bit ADC, multiple timers, EUSART, MSSP (SPI/I2C) peripherals, and Microchip's nanoWatt XLP ultra-low-power technology. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, peripherals and I/O on one die. Within the semiconductor taxonomy, an MCU sits under microcontroller -> embedded processor -> integrated circuit -> semiconductor. The '8-bit' designation refers to the native data bus width; PIC16 MCUs use a modified Harvard RISC architecture with separate program and data buses, which accelerates instruction fetch and allows single-cycle execution for most instructions. This family is widely used in cost-sensitive, low-power embedded designs where deterministic real-time behaviour matters more than raw throughput. Key features of the PIC16F1527T-I/PT include 28 KB Flash with self-programmability, 1.5 KB SRAM, 256 B EEPROM, a 12-bit differential ADC with computed channels, up to 54 digital I/O pins, four 8-bit timers plus two CCP and one ECCP module, two EUSART, two MSSP (SPI/I2C), an integrated temperature indicator, and nanoWatt XLP sleep currents below 1 uA. The 64-TQFP package measures 10 x 10 mm with a 0.5 mm lead pitch. Architecturally, the PIC16F1527T-I/PT uses a 14-bit instruction word and a 16-level hardware stack, with an interrupt controller supporting both core and peripheral interrupt sources. The 12-bit ADC is supported by a dedicated FVR (Fixed Voltage Reference) and a DAC, enabling ratiometric measurements and on-chip analogue signal conditioning without external components. Typical applications include consumer appliance control, sensor interface modules, battery-powered handheld instruments, simple motor and lighting controllers, and industrial sensor hubs. The wide 1.8-5.5 V supply range allows direct operation from 2xAA/AAA cells or 3.3 V/5 V regulated rails. When designing with this MCU, confirm that the application's interrupt latency budget is compatible with the 20 MHz core; pin remapping is limited and I/O assignments should be planned during PCB layout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC16F15313-E/RF

PIC16F15313-E/RF - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip

The Microchip Technology PIC16F15313-E/RF is an 8-bit PIC microcontroller from the PIC16F15313 family featuring the enhanced mid-range core running at up to 32 MHz, with 3.5 KB (2K x 14) of self-read/write Flash program memory, 256 bytes of RAM, and packaged in an 8-pin UDFN (3x3 mm) with exposed pad (RF suffix). The part carries the E (extended) temperature grade and is part of Microchip's eXtreme Low Power (XLP) family, designed for battery-powered and energy-harvesting applications. An 8-bit microcontroller (MCU) is a compact processor integrating CPU, Flash, RAM, and peripherals on a single die. Within the broader taxonomy, the PIC16F15313-E/RF sits in the hierarchy: 8-bit MCU -> PIC16 family -> enhanced mid-range core -> PIC16F153xx sub-family -> eXtreme Low Power (XLP) series -> embedded microcontroller. Its 49-instruction set and 16-level stack make it code-compatible with the wider PIC16F1xxx family, allowing easy migration and tool reuse with MPLAB X IDE and the XC8 compiler. Key features include 4x 10-bit PWMs, a 10-bit ADC with computation, a 5-bit DAC, comparators, 4x Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), an EUSART, and SPI/I2C interfaces. Peripheral Pin Select (PPS) remaps digital peripherals to any I/O pin, simplifying PCB routing on this small 8-pin package. The XLP features IDLE and DOZE low-power modes plus Peripheral Module Disable (PMD) to switch off unused peripherals, achieving nanoWatt sleep currents. Typical applications include wireless charging control loops (replacing ASIC-based solutions), IoT sensor nodes, low-cost consumer electronics, LED lighting controllers, and battery-powered remote controls. The small 3x3 mm UDFN footprint suits space-constrained wearables and portable medical accessories. When designing with this MCU, leverage Peripheral Pin Select to free PCB routing from the strict pin-per-peripheral mapping of older PICs. Use PMD aggressively in sleep loops to drop quiescent current below 1 uA, and verify the UDFN exposed pad is properly soldered for thermal dissipation and electrical ground. This page synthesizes distributor pricing, drop-in alternative MPNs, comparison tables, and practical design notes not found in the manufacturer datasheet, giving engineers and procurement a single reference for the PIC16F15313-E/RF.

Cotización Contacto

PIC16F15313-E/SN

PIC16F15313-E/SN - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC16F15313-E/SN is an 8-bit PIC16F microcontroller (MCU) featuring 3.5KB (2K x 14) of Flash program memory, 256 bytes of RAM, and a 32MHz internal oscillator, housed in an 8-pin SOIC package. It belongs to the PIC16F15313 family of "full-featured" low-pin-count MCUs and operates from 2.3V to 5.5V across the extended industrial temperature range (-40C to +125C). An 8-bit microcontroller (MCU) is a small, low-power computer-on-a-chip that integrates a CPU, memory, and programmable I/O on a single die; the PIC16F15313-E/SN sits within the PIC16 family -> PIC16F1xxx enhanced mid-range -> 8-bit PIC microcontroller -> embedded MCU hierarchy. By integrating peripherals such as a DAC, ADC, comparators, PWM, CLC (Configurable Logic Cell), CWG (Complementary Waveform Generator), and EUSART/SPI/I2C, it eliminates many external components that designers previously had to add separately. Key features include 4xPWMs, 4x Configurable Logic Cells (CLC), 1x 5-bit DAC, 1x 10-bit ADC, 2x comparators with selectable references, a Complementary Waveform Generator (CWG), and EUSART with auto-baud detect. The device also supports SPI and I2C peripherals for sensor and display interfacing, plus eXtreme Low Power (XLP) technology for ultra-low sleep currents in battery-powered applications. The PIC16F15313-E/SN uses Microchip's enhanced mid-range 8-bit core, providing a single-cycle instruction set and 49 instruction types for efficient code density. Internal voltage regulation and a wide operating voltage range (2.3V to 5.5V) enable direct Li-ion, 3.3V, or 5V system operation without external regulators. The CLC blocks allow glue-logic replacement directly inside the MCU, reducing PCB complexity and BOM cost. Typical applications include Qi 1.1 5W wireless charging controllers, IoT sensor nodes, LED lighting controllers, small consumer appliances, battery-powered toys, fan and pump controllers, and general-purpose logic-replacement boards where a compact 8-pin footprint is required. When designing with this device, prioritize pin allocation early because the 8-pin SOIC exposes only 6 usable I/O pins. Use the MPLAB X IDE with MPLAB XC8 compiler and consider migrating legacy PIC10/12/16 code to the unified PIC16F1xxx platform to maximize code reuse. Add a 0.1uF decoupling capacitor within 5mm of VDD for stable operation.

Cotización Contacto

PIC16F15313-E/SNVAO

PIC16F15313-E/SNVAO - 8-bit MCU, 3.5KB Flash, 32MHz, AEC-Q100 | Microchip

The Microchip Technology PIC16F15313-E/SNVAO is an automotive-grade, full-featured 8-bit PIC16 microcontroller built on an enhanced mid-range core with 49 instructions and 16 stack levels, delivering 32 MHz CPU performance from a 2.3 V to 5.5 V supply. The device integrates 3.5 KB (2K x 14) of self read/write Flash program memory, 256 bytes of RAM, 4x 10-bit PWMs, a 5-channel 10-bit ADC, a 5-bit DAC, two comparators, a Complementary Waveform Generator (CWG), EUSART, and SPI/I2C peripherals, all in a compact 8-pin SOIC package. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral I/O on one die. Within the broader taxonomy, the PIC16F15313 belongs to the 8-bit MCU class, sits inside the PIC16 family of mid-range cores, and ships with Core Independent Peripherals (CIPs) that operate without CPU intervention, freeing the core for power-saving tasks. eXtreme Low Power (XLP) features such as IDLE and DOZE modes, plus Peripheral Module Disable (PMD), make the device especially attractive for battery-powered or energy-harvesting designs. Key differentiating features include the Memory Access Partition (MAP) for bootloader-style code protection, Peripheral Pin Select (PPS) for flexible signal routing, and an internal temperature indicator. The "VAO" suffix and operating range of -40 °C to +125 °C confirm AEC-Q100 automotive qualification, distinguishing this variant from the industrial-grade PIC16F15313-I/SN. The 8-SOIC footprint (3.90 mm body width) eases hand-soldering and visual inspection while remaining compatible with high-volume SMT lines. Architecturally, the enhanced mid-range core executes most instructions in one instruction cycle and supports interrupt-driven CIPs, allowing deterministic response times without software polling. The integrated 5-bit DAC and rail-to-rail comparators enable closed-loop analog control without external components, reducing BOM cost and PCB area in sensor-interface, lighting-control, and consumer appliance designs. Designers migrating from older PIC10/12/16F parts benefit from code compatibility through the standard instruction set. Typical applications include automotive body controllers, sensor signal conditioning, low-power IoT edge nodes, LED lighting control loops, and consumer remote-control transmitters. The combination of CIPs, PPS, and XLP modes also makes the part a strong fit for sealed-housing applications where post-assembly firmware updates via the self-write Flash minimize mechanical access requirements. When designing with this device, allocate the brown-out and watchdog timer configuration early, because changing these settings late in the development cycle can compromise functional safety arguments in automotive programs. Use the MAP feature to lock the bootloader region from accidental overwrite by the application image.

Cotización Contacto

PIC16F15313-I/P

PIC16F15313-I/P - 8-bit MCU, 3.5KB Flash, 32MHz, XLP | Microchip

The Microchip Technology PIC16F15313-I/P is an 8-bit PIC RISC microcontroller with 3.5KB Flash, 256B RAM, and 32MHz operation, housed in an 8-pin PDIP through-hole package. It operates from 2.3V to 5.5V and features eXtreme Low-Power (XLP) technology, 4 PWMs, comparator, ADC, 5-bit DAC, 4x Configurable Logic Cells (CLC), CWG, EUSART, and SPI/I2C peripherals. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM), and programmable I/O peripherals on one die. The PIC16F15313 belongs to the PIC16 family of 8-bit RISC microcontrollers, which fall within the broader category of embedded processors and microcontrollers, themselves a subset of semiconductor ICs used for system control and signal processing tasks in nearly every electronic product. Key features include 3.5KB self-programmable Flash program memory, 256B SRAM, 4 PWMs with complementary outputs, a 10-bit ADC with computation, a 5-bit DAC, comparator, and 4 Configurable Logic Cells that implement custom logic gates and state machines without external components. The 32MHz internal oscillator and XLP technology support sleep currents as low as 30 nA typical, enabling battery-powered designs. The PIC16F15313 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction set and hardware Multiply, peripheral pin select (PPS) for flexible signal routing, and on-board debugging via MPLAB ICD. Its integration of CIPs (Core Independent Peripherals) means many functions like waveform generation, signal conditioning, and timing run autonomously without CPU intervention, freeing the core for application logic. Typical applications include IoT sensor nodes, low-power wireless charging controllers (Qi 1.1 5W reference), battery-powered home automation, LED lighting controls, and general-purpose consumer product control. With only 6 I/O pins in the 8-pin PDIP, the device targets compact designs where software-defined peripheral functions (CLC, CWG, NCO) replace external glue logic. When designing with this device, ensure the ICSP programming pins (ICSPCLK/ICSPDAT) are accessible for in-circuit programming and that the MCLR pin has a proper pull-up circuit. Use the PPS feature carefully because re-routing pins may conflict with peripheral functions, and always check that the chosen clock mode provides adequate timing margin for the application. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a complete commercial and engineering view of the PIC16F15313-I/P.

Cotización Contacto

PIC16F15313-I/RF

PIC16F15313-I/RF - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip PIC16F15313-I/RF is an 8-bit PIC® XLP™ 16F-series microcontroller featuring 3.5 KB (2K x 14) of FLASH program memory, 256 bytes of RAM, and a maximum CPU clock speed of 32 MHz, housed in an 8-pin DFN (3x3 mm) package with exposed thermal pad. A microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory (typically FLASH), volatile working memory (RAM), and a rich set of on-chip peripherals such as timers, ADCs, communication interfaces, and configurable logic. MCUs sit at the top of the embedded-computing hierarchy - more capable than a simple ASIC for fixed logic, less expensive than a microprocessor/MPU that requires external RAM and storage, and indispensable for almost every modern electronic product. The PIC16F15313 specifically belongs to Microchip's enhanced mid-range 8-bit family (PIC16), which adds richer peripheral integration and lower power consumption than legacy baseline PIC10/12/16 parts. Key features include 4 PWM channels, an on-chip comparator, a 5-bit DAC, a 10-bit ADC with multiple channels, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and both EUSART and SPI/I2C serial interfaces. The XLP (eXtreme Low Power) designation brings sub-uA sleep currents, making this part attractive for battery-powered or energy-harvesting designs. Industrial-grade operating temperature range is -40C to +85C, and supply voltage spans 2.3V (at 16 MHz) to 5.5V. Architecturally the PIC16F15313 uses an enhanced mid-range 8-bit RISC core with a hardware multiplier, providing deterministic instruction execution and a single-cycle 8x8 multiply. The device integrates Core Independent Peripherals (CIPs) - CLC, CWG, NCO, and PWM - that operate without CPU intervention, offloading timing-critical functions and reducing firmware complexity while lowering overall system power. Typical applications include IoT sensor nodes, low-cost consumer appliances, white goods control boards, battery-powered wireless charging controllers, LED lighting effects, and general-purpose 8-bit embedded logic replacement. Designers choose it when cost, small footprint, and ultra-low standby power outweigh the need for higher MIPS. When laying out the PCB, follow Microchip's DFN-8 land-pattern recommendation and provide a thermal pad soldered to a copper pour for best thermal performance. Decoupling VDD with a 100 nF ceramic capacitor placed within 2 mm of the pin is recommended for ADC accuracy at higher sampling rates. This page synthesizes Microchip datasheet parameters, current distributor pricing, drop-in same-package alternatives, and practical design notes not found in the datasheet alone - giving engineers a one-stop reference for evaluating the PIC16F15313-I/RF against the PIC16F15313 family and competitor parts.

Cotización Contacto

PIC16F15313-I/SN

PIC16F15313-I/SN - 8-Bit 32MHz MCU, 3.5KB Flash | Microchip

The Microchip Technology PIC16F15313-I/SN is an 8-bit PIC16F microcontroller with eXtreme Low-Power (XLP) technology, 32 MHz CPU speed, 3.5 KB Flash program memory, 256 B SRAM, and 6 I/O pins, housed in an 8-pin SOIC (SN) package. According to the Microchip PIC16F15313 datasheet, the device integrates Intelligent Analog peripherals (10-bit ADC, 5/8-bit DAC, comparators), Core Independent Peripherals (CIPs) such as four Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and communication peripherals (EUSART, SPI, I2C). An 8-bit microcontroller is a single-chip computer that processes data 8 bits at a time, executing instructions from on-chip Flash program memory and operating on registers and SRAM. PIC microcontrollers use a RISC-based Harvard architecture (separate program and data buses), positioning them under the broader hierarchy: microcontroller -> embedded processor -> integrated circuit -> semiconductor. The 8-bit segment remains the workhorse of cost-sensitive, low-power consumer and industrial designs because of deterministic interrupt response, ease of programming in C or assembly, and the rich ecosystem of MPLAB X development tools. The PIC16F15313's key differentiating features include four 10-bit PWM outputs with independent timers, four Configurable Logic Cells that implement custom Boolean functions without CPU intervention, and a Complementary Waveform Generator for half-bridge and full-bridge drive. The device supports 1.8V-5.5V operation and features nanoWatt XLP sleep currents in the sub-100 nA range, enabling battery-powered designs that run for years on a single cell. Architecturally, the PIC16F15313 family uses a 14-bit instruction word and a 32 MHz internal oscillator, allowing software execution at 8 MIPS. The device integrates a power-on reset, brown-out reset, and low-voltage programming, eliminating external supervisory components. The 256 B SRAM and 3.5 KB Flash are sufficient for state machines, sensor processing, and small protocol stacks. Typical applications include battery-operated sensor nodes, IoT edge devices, consumer remote controls, LED lighting controllers, low-end motor control loops, and Qi 1.1 wireless-charging transmitter controllers. The 8-pin footprint makes it one of the smallest PIC16F devices available, allowing drop-in use in space-constrained products. When designing with the PIC16F15313-I/SN, ensure the ICSPDAT/ICSPCLK pin sharing is managed and that the MCLR pull-up is correctly configured for in-circuit serial programming. The four PWM channels are useful for driving LEDs or brushed DC motors without external timers. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and BOM decisions.

Cotización Contacto

PIC16F15313T-I/SN

PIC16F15313T-I/SN - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC16F15313T-I/SN is an 8-bit PIC microcontroller based on the enhanced mid-range core, operating at up to 32 MHz with 3.5 KB (2K x 14) of Flash program memory in an 8-pin SOIC (SN) package. The device is part of the PIC16(L)F153xx family and integrates Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for battery-friendly embedded designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates an 8-bit CPU core, Flash program memory, RAM, and a mix of digital and analog peripherals. PIC microcontrollers sit in the broader hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC16F15313T-I/SN belongs to the Microchip enhanced mid-range family, which adds C compiler-friendly instructions, peripheral pin select, and faster context switching relative to legacy baseline or mid-range cores. Key features include 256 bytes of SRAM, four 10-bit PWMs, a 5-bit DAC, a comparator, a 10-bit ADC, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), one EUSART, and SPI/I2C interfaces. The XLP IDLE and DOZE modes together with Peripheral Module Disable (PMD) allow aggressive current reduction by gating unused peripheral clocks. Peripheral Pin Select (PPS) lets remapable digital functions move between pins, simplifying PCB routing on the small 8-pin footprint. Architecture-wise the chip combines an 8-bit data path with a 14-bit instruction word, providing 49 instructions and 16 stack levels. The on-board 32 MHz internal oscillator eliminates the need for an external crystal in cost-sensitive designs, while the low-power brown-out reset and watchdog timer improve field reliability. Typical applications include consumer remote controls, IoT sensor nodes, low-power wireless companions, LED lighting controllers, battery chargers, and small appliance controls. Industrial use cases span HVAC damper actuators, smart thermostats, and portable instrumentation where the SOIC-8 footprint and 32 MHz performance fit the bill. When designing with this part, reserve an unused GPIO for In-Circuit Serial Programming (ICSP) to allow firmware updates in the field, and budget Flash endurance of 10K erase/write cycles plus 40-year data retention per Microchip datasheet. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC16F15323-E/JQ

PIC16F15323-E/JQ - 8-bit MCU 3.5KB Flash 32MHz XLP | Microchip

The Microchip Technology PIC16F15323-E/JQ is an 8-bit PIC microcontroller featuring 3.5 KB Flash program memory, 256 bytes of SRAM, and a maximum CPU clock of 32 MHz, housed in a 16-pin UQFN (4x4 mm) package with an exposed pad. It integrates four PWM channels, a comparator, a 5-bit DAC, a 10-bit ADC, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), EUSART, and SPI/I2C peripherals, all within the eXtreme Low-Power (XLP) PIC16F153xx family architecture. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripheral blocks on a single silicon die. The 8-bit PIC16F architecture from Microchip uses a modified Harvard structure with a RISC instruction set optimized for deterministic interrupt response and low power consumption. Within the broader taxonomy, the PIC16F15323 belongs to the 8-bit MCU family -> PIC16 family -> PIC16F153xx sub-family -> XLP low-power portfolio, which sits below 16-bit dsPIC and 32-bit ARM Cortex-M families in processing power but excels in cost-sensitive and battery-powered applications. Key differentiating features include a 2.3V to 5.5V wide operating voltage range, an extended industrial temperature range of -40C to +125C, 12 general-purpose I/O lines, and 6 ADC channels. The XLP technology delivers typical sleep currents below 50 nA with full RAM retention, enabling multi-year battery life on coin-cell or 2xAA supplies. Core Independent Peripherals (CIPs) such as CLC, CWG, and NCO allow hardware-level signal generation and logic functions without CPU intervention, reducing power consumption and freeing the core for application tasks. Technically, the device uses a 14-bit instruction word with a 2-stage pipeline, supports in-circuit serial programming (ICSP) and enhanced flash cell technology rated for 100K erase/write cycles. The integrated 32 MHz internal oscillator eliminates the need for an external crystal in most designs, and the on-chip voltage reference and temperature indicator simplify analog designs. Typical applications include IoT sensor nodes, battery-powered remote controls, low-cost consumer electronics, LED lighting controllers, appliance user-interface panels, and wearable fitness/health peripherals. The 16-pin UQFN package with EP enables compact PCB designs as small as 5 mm x 5 mm. When designing, place a 0.1 uF decoupling capacitor as close as possible to VDD and ensure the exposed pad is soldered to a thermal/power ground plane. The PIC16F15323 is pin-compatible with other PIC16F153x3 family members, allowing memory or peripheral upgrades without PCB redesign. This page synthesizes distributor pricing, parametric alternatives, and practical design notes not found in the manufacturer datasheet, with all data verified against current web sources as of 2026-09-19.

Cotización Contacto

PIC16F15323-E/SL

PIC16F15323-E/SL - 8-bit MCU, 3.5KB Flash, 32MHz, 14-SOIC | Microchip

The Microchip Technology PIC16F15323-E/SL is an 8-bit PIC16 microcontroller in the PIC16(L)F153xx family, featuring 3.5KB (2K x 14) of self-read/write Flash program memory, 256 bytes of RAM, and a 32MHz internal oscillator, housed in a 14-pin SOIC (SL) package with the extended (-E) temperature grade of -40C to +125C. A PIC16 8-bit microcontroller is a compact RISC processor built on Microchip's Enhanced Mid-Range Core, executing 49 instructions across 16 stack levels. Within the broader taxonomy, the PIC16F15323 belongs to the microcontroller (MCU) family, then to 8-bit MCUs, then to the PIC16 enhanced mid-range sub-family, and finally to the XLP (eXtreme Low-Power) category that targets battery-powered and always-on embedded designs. The PIC16F153xx line introduces Core Independent Peripherals (CIPs), Intelligent Analog, and Peripheral Pin Select (PPS), enabling designers to offload tasks such as signal generation, waveform detection, and communication framing from the CPU. Key differentiating specifications include: a 32MHz maximum CPU clock (8MHz instruction rate with 4-cycle execution), 12 I/O pins with PPS remapping, four 10-bit PWMs with complementary waveform generation, two operational amplifiers or comparators, a 5-bit DAC, a 10-bit ADC with up to 11 channels, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and EUSART plus SPI/I2C communication. The device also integrates the eXtreme Low-Power (XLP) IDLE and DOZE modes plus Peripheral Module Disable (PMD) for fine-grained power gating. On-chip peripherals such as the CLC, CWG, and NCO let complex timing or logic tasks run without CPU intervention, reducing firmware complexity and active-mode current. Typical applications include battery-powered IoT sensor nodes using the XLP sleep modes, LED lighting controllers leveraging the 4x PWMs and CWG for high-resolution dimming, consumer appliances requiring touch or capacitive sensing through the CIP block, low-cost motor control loops, and small home appliances where the integrated op-amps remove external analog components. The -E (extended) temperature grade and 14-SOIC footprint also suit industrial control boards and distributed sensor hubs. Designers should budget for a 1.8V to 5.5V supply, ensure decoupling on VDD with a 100nF ceramic cap placed within 5mm of the pin, and reserve the ICSP/ICD pins for in-circuit programming and debugging. The PPS feature lets peripheral signals be remapped across most I/O pins, simplifying PCB routing when the same die must fit multiple board layouts. For sourcing, the PIC16F15323-E/SL is widely stocked at major distributors in tube packaging as of 2026-09-19. The same die ships in 8-pin variants (PIC16F15313) and larger pin-count variants (PIC16F15344, PIC16F15356), giving designers a migration path within the family. This page synthesizes distributor pricing, drop-in SOIC-14 alternatives, and design notes that extend the manufacturer datasheet.

Cotización Contacto

PIC16F15323-E/ST

PIC16F15323-E/ST - 8-Bit 32MHz MCU, 3.5KB Flash, XLP | Microchip

The Microchip PIC16F15323-E/ST is an 8-bit PIC microcontroller from the PIC16F153xx family that combines Intelligent Analog, Core Independent Peripherals (CIPs), and communication peripherals with eXtreme Low-Power (XLP) technology. Built on an enhanced mid-range core with 49 instructions and 16 stack levels, it operates at up to 32 MHz, integrates 3.5 KB (2K x 14) of self-read/write Flash, 256 bytes of SRAM, and is housed in a 14-pin TSSOP package (suffix /ST). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and programmable I/O peripherals. The PIC16 architecture belongs to the broader 8-bit microcontroller category, which sits within the embedded computing -> microcontroller -> MCU IC -> semiconductor taxonomy. The 14-pin TSSOP variant is part of Microchip's general-purpose low-pin-count PIC16 family, intended for compact, low-power designs. Key differentiating features include 4x 10-bit PWMs with complementary waveform generation, 2x Configurable Logic Cells (CLC), a 5-bit DAC, a comparator, a 10-bit ADC with computation, plus EUSART, SPI, and I2C communication interfaces. Peripheral Pin Select (PPS) allows flexible signal routing, while Peripheral Module Disable (PMD) along with IDLE and DOZE modes enables aggressive power savings under battery operation. XLP technology supports nanoWatt sleep currents suitable for energy-harvesting or coin-cell applications. Typical applications span consumer electronics, IoT sensor nodes, battery-powered handheld devices, low-cost motor control (small DC fans, PWM-driven LED strings), and home appliance user-interface boards. The combination of CLCs, PWM, and ADC makes it well suited to mixed-signal front ends without external glue logic. When designing with the PIC16F15323-E/ST, route the ICSP/PGD/PGC programming signals to dedicated pins and provide adequate decoupling (100 nF close to VDD plus a bulk cap). Verify the chosen supply voltage (2.3V-5.5V) against the maximum clock frequency required, because the 32 MHz figure requires VDD >= 2.7V per the datasheet. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC16F15323-I/JQ

PIC16F15323-I/JQ - 8-bit MCU, 3.5KB Flash, 256B RAM | Microchip

The Microchip Technology PIC16F15323-I/JQ is an 8-bit PIC RISC microcontroller built around the enhanced mid-range core with 49 instructions and 16 stack levels, providing 3.5 KB of self-read/write Flash program memory, 256 bytes of SRAM, and up to 32 MHz operation in a 16-pin UQFN package with an exposed thermal pad. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip that integrates a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and a mix of analog and digital peripherals around a single 8-bit data bus. Within the broader taxonomy, the PIC16F15323 belongs to the 8-bit PIC MCU family -> enhanced mid-range core -> low-power XLP sub-family -> intelligent analog and Core Independent Peripherals (CIPs) branch -> semiconductor. The CIP philosophy places tasks like waveform generation, signal conditioning, and communication in hardware blocks so the CPU can remain in sleep, dramatically cutting system power. Key features of the PIC16F15323-I/JQ include four 10-bit PWMs, a 5-bit and 10-bit DAC, a comparator, an ADC with acquisition logic, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), an EUSART, and SPI/I2C peripherals. The device supports Peripheral Pin Select (PPS), which allows most digital I/O to be remapped to a wide range of physical pins - greatly easing PCB layout when signal routing conflicts arise. The IC uses a CMOS process with eXtreme Low Power (XLP) technology, providing IDLE and DOZE power-saving modes plus Peripheral Module Disable (PMD) to shut down unused peripherals. The device operates from 2.3 V to 5.5 V, supports both 3.3 V and 5 V rails, and is offered in industrial -40 C to +85 C temperature grade per the -I suffix. The UQFN-16 (JQ) exposed-pad package gives a compact 4x4 mm footprint suitable for space-constrained designs and aids thermal dissipation through the bottom pad. Typical applications include low-power IoT sensor nodes, consumer appliances with HMI control, battery-powered handheld instruments, LED lighting controllers using the CWG, and general-purpose logic replacement using the CLC blocks. The combination of small footprint, integrated intelligent analog, and XLP modes also suits remote controls, toys, and wearables. When designing with this part, place a 0.1 uF decoupling capacitor as close as possible to the VDD pin and tie the exposed thermal pad (EP) to a solid ground plane for electrical and thermal performance. Use PPS early in the schematic phase to lock pin assignments before laying out the PCB, since reassigning peripherals later may force a re-spin. This page synthesizes distributor pricing, drop-in alternatives, design notes and a side-by-side parametric comparison not always found in the manufacturer datasheet alone.

Cotización Contacto

PIC16F15323-I/P

PIC16F15323-I/P - 8-bit MCU, 3.5KB Flash, 32MHz, 14-PDIP | Microchip

The Microchip Technology PIC16F15323-I/P is an 8-bit PIC microcontroller built on the enhanced mid-range core with 49 instructions, 16 stack levels, and self read/write Flash, integrating 3.5KB (2K x 14) of program memory and 256 bytes of SRAM in a 14-pin PDIP (P) through-hole package. Operating from 2.3V to 5.5V with a 32MHz internal oscillator, the device pairs eXtreme Low-Power (XLP) IDLE and DOZE modes with a peripheral module disable (PMD) scheme and peripheral pin select (PPS) to optimize active and standby consumption in battery-powered systems. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and configurable peripherals. The PIC16F15323 belongs to the 8-bit PIC microcontroller family, which sits within the broader class of microcontrollers, embedded processors, and finally semiconductors. The 8-bit PIC architecture executes one instruction per cycle using a RISC-style instruction set, and the enhanced mid-range core extends this with 49 instructions, deterministic interrupt latency, and 16 hardware stack levels. Core differentiating features include 4x 10-bit PWM channels, a 5-bit DAC, a 10-bit ADC with computation, an on-chip comparator, two Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and serial peripherals including EUSART, SPI, and I2C. PPS remaps most digital peripherals to nearly any I/O pin, simplifying PCB routing on the 14-pin package. Self-write capable Flash supports in-field firmware updates via the bootloader-friendly architecture. Typical applications include low-power IoT sensor nodes, consumer white goods, LED lighting controllers, battery-powered handheld instruments, and small automation subsystems. The combination of 32MHz performance, CLC-based custom logic, and 10-bit ADC with computation makes the part well suited for sensor conditioning loops where analog signal chains and digital control share the same MCU. The automotive and industrial grade variants (PIC16F15323-E/P) extend the operating temperature to +125C. When designing with this device, mind the I/O count: 14-pin PDIP exposes 12 GPIO-capable pins after power and reset allocation. Decouple VDD with a 0.1uF ceramic capacitor placed within 5mm of the IC, and reserve the MCLR pin for a proper reset network unless the internal MCLR is configured in the configuration words. This page synthesizes XAIPART distributor pricing, drop-in PIC16F153xx and PIC16F152xx alternatives, and practical design notes that complement (rather than duplicate) the manufacturer datasheet, giving procurement and engineering teams a single, citable reference.

Cotización Contacto

PIC16F15323-I/SL

PIC16F15323-I/SL - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15323-I/SL is an 8-bit PIC microcontroller from the PIC16(L)F153XX family, delivering up to 32 MHz CPU performance with 3.5 KB (2K x 14) self-programmable Flash program memory in a 14-pin SOIC (SL) package. It features 256 bytes of RAM, an Enhanced Mid-Range core with 49 instructions, 16 stack levels, and integrates core-independent peripherals such as 4x 10-bit PWMs, a 5-bit DAC, a comparator, a Configurable Logic Cell (CLC) block, Complementary Waveform Generator (CWG), and EUSART/SPI/I2C communication. The -I suffix indicates the industrial temperature range of -40C to +85C, and the SL suffix denotes the 14-lead narrow-body SOIC surface-mount package. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash, RAM, EEPROM), and programmable peripherals into one IC. The PIC16F15323 belongs to the 8-bit enhanced mid-range MCU hierarchy, which sits between Microchip's baseline 8-bit cores and 16-bit PIC24/dsPIC families. Its peripheral pin select (PPS) and peripheral module disable (PMD) features allow flexible pin mapping and fine-grained power gating, while eXtreme Low Power (XLP) IDLE and DOZE modes help designers minimize active and standby current for battery-powered applications. Key features of the PIC16F15323 include eXtreme Low Power (XLP) technology for sub-microamp sleep currents, 4x 10-bit PWM outputs, 2x comparators with selectable references, a 5-bit DAC, 4x Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), EUSART (enhanced USART), SPI, I2C, and a 10-bit ADC. The device supports self-read/write Flash with a wide 2.3V to 5.5V operating voltage, making it suitable for both 3.3V and 5V systems. The PIC16F15323 also supports in-circuit serial programming (ICSP) and debugging. The PIC16F15323 uses a Harvard architecture with separate program and data buses, an internal oscillator accurate to ±1% typical, and a low-power 32 kHz secondary oscillator for RTC-like functions. This architecture enables deterministic instruction execution and rapid interrupt response, both of which are valuable in real-time control loops such as LED dimming, motor commutation, and sensor signal conditioning. Combined with 4 CLC blocks, designers can implement custom combinational and sequential logic in hardware without external glue chips. Typical applications include low-power IoT sensor nodes, LED lighting and signage controllers, battery-powered consumer devices, automotive body and accessory modules (where AEC-Q100 is not required), small home appliances, and general-purpose digital control replacing discrete logic. The combination of analog peripherals (ADC, DAC, comparator) and communication peripherals (EUSART, SPI, I2C) makes it a flexible system-on-chip for cost-sensitive embedded designs. When designing with this device, ensure that the internal oscillator accuracy is acceptable for your UART timing budget; otherwise, an external crystal or resonator may be required. Use Microchip's MPLAB X IDE and XC8 compiler for firmware development, and configure unused pins as digital low-power outputs to minimize current draw in sleep modes. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, providing a consolidated engineering reference for the PIC16F15323-I/SL.

Cotización Contacto

PIC16F15323T-I/SL

PIC16F15323T-I/SL - 8-bit 32MHz XLP MCU, 3.5KB Flash | Microchip

The Microchip Technology PIC16F15323T-I/SL is an 8-bit PIC® microcontroller built around the PIC16 CPU core running at up to 32 MHz, packaged in a 14-pin SOIC (SL) with Tape & Reel delivery. It integrates 3.5 KB (2K x 14) of Flash program memory, 256 bytes of SRAM, and Microchip's eXtreme Low-Power (XLP) technology for battery-friendly operation. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip that combines a CPU, program memory (Flash/ROM), working memory (SRAM), and peripherals on a single die. PIC microcontrollers use a modified Harvard RISC architecture with a 14-bit instruction word optimized for deterministic interrupt response and very low active/idle power, making them a workhorse of the 8-bit embedded market alongside the AVR and 8051 families. Key features of the PIC16F15323T-I/SL include a 5-bit DAC, 10-bit ADC with computation, two comparators, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), four PWM channels, and a 32 MHz internal oscillator. Communication is handled by EUSART, SPI, and I²C peripherals, while Core Independent Peripherals (CIPs) such as the CLC and CWG offload tasks from the CPU, lowering power and code size. The device operates from 2.3 V to 5.5 V with a -40 °C to +85 °C industrial temperature range and is qualified to MSL Level 3 (168 hours). The XLP variants target nanoWatt sleep currents, making the part attractive for battery-powered sensor nodes, IoT endpoints, and always-on household appliances where sleep current dominates the energy budget. Typical applications include low-power IoT sensor nodes, battery-powered home appliances, LED lighting control, motor control loops, and general-purpose logic replacement. Designers should consult Microchip's MPLAB X IDE and XC8 compiler toolchain and reference the CLC/CWG application notes from Microchip for hard real-time tasks. When designing in the PIC16F15323T-I/SL, decouple VDD with a 100 nF ceramic capacitor placed within 5 mm of the pin and use the internal 32 MHz HFINTOSC to avoid external crystal pads on cost-sensitive boards. The CWG block can synthesize complementary gate-drive waveforms, but always verify dead-band timing against your MOSFET's input capacitance.

Cotización Contacto

PIC16F15323T-I/ST

PIC16F15323T-I/ST - 8-Bit 32MHz MCU 3.5KB Flash 14-TSSOP | Microchip

The Microchip Technology PIC16F15323T-I/ST is an 8-bit PIC microcontroller from the PIC16(L)F153xx family, integrating 3.5KB (2K x 14 words) of Flash program memory and 256 bytes of SRAM in a 14-pin TSSOP package. The device runs at up to 32MHz from the internal oscillator and features Microchip's enhanced mid-range core with 49 instructions and 16-level deep hardware stack. Tape-and-reel packaging (-T suffix) and the industrial -40C to +85C temperature range (I-grade) target volume production. What is a PIC16 8-bit microcontroller? An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile Flash program memory, data RAM, and a rich set of peripherals on one die. PIC16 MCUs use a RISC-style modified Harvard architecture and sit inside the broader category of microcontrollers -> embedded controllers -> semiconductor ICs. The PIC16F153xx family adds Core Independent Peripherals (CIPs) and eXtreme Low Power (XLP) features, enabling complex timing, signal generation, and communication tasks without CPU involvement. The PIC16F15323T-I/ST integrates four 10-bit PWMs, a 5-bit DAC, comparators with selectable references, a 10-bit ADC with computation, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and an EUSART plus SPI/I2C communications. Peripheral Pin Select (PPS) allows flexible remapping of digital peripherals to any I/O pin, simplifying PCB routing on the 14-pin footprint. Architecturally, the device pairs the enhanced mid-range core with Intelligent Analog and CIP blocks to offload real-time tasks from the CPU, achieving deterministic response in motor control, lighting, and sensor-interface applications. The XLP feature set provides IDLE and DOZE low-power modes, plus Peripheral Module Disable (PMD) to shut down unused peripherals and minimize quiescent current. Typical applications include low-power IoT sensor nodes, consumer appliances with capacitive touch, LED lighting controllers, battery-powered handheld instruments, and small motor/valve drivers. The 14-TSSOP footprint fits compact boards where the PIC10/PIC12 8-pin parts cannot offer enough peripherals. When designing with this MCU, leverage Peripheral Pin Select to route peripherals to convenient pins, and use CLC + CWG combinations for hardware-driven timing so the CPU can sleep in XLP modes. Always configure unused pins as outputs and ensure ICD/ICSP connections follow Microchip guidelines for in-circuit debugging. This page combines authoritative datasheet specifications, distributor pricing, drop-in TSSOP alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides, helping engineers make a confident sourcing and design decision.

Cotización Contacto

PIC16F15324-E/7NVAO

PIC16F15324-E/7NVAO - 7KB Flash MCU, 32MHz, 16-VQFN | Microchip

The Microchip Technology PIC16F15324-E/7NVAO is an 8-bit PIC microcontroller built around the enhanced mid-range core, integrating 7KB of Flash program memory (4K x 14 words), 512 bytes of SRAM, and a rich set of Core Independent Peripherals (CIPs). The device runs at up to 32 MHz and ships in a 16-pin VQFN (4x4 mm) package with an exposed thermal pad, supplied in automotive-grade AEC-Q100 qualification per the /VAO suffix. Its combination of intelligent analog and eXtreme Low-Power (XLP) features targets low-power embedded designs that need deterministic peripheral behaviour without CPU intervention. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data memory, and peripherals on a single die. The PIC16F family belongs to the mid-range PIC architecture hierarchy: 8-bit MCU -> enhanced mid-range core -> PIC16F1xxx family -> 16-pin sub-family. PIC microcontrollers are widely used in automotive body electronics, white goods, sensor nodes, and consumer devices because they offer deterministic instruction execution, low active and sleep currents, and a long-life Flash program memory that supports frequent firmware updates in the field. The part integrates 4x 10-bit PWMs with complementary waveforms, a 5-bit DAC, a comparator, a 10-bit ADC with computation, the Configurable Logic Cell (CLC), the Complementary Waveform Generator (CWG), and two Enhanced USART modules that also support SPI/I2C and LIN master mode. The Peripheral Pin Select (PPS) feature allows digital peripheral I/O to be remapped to most device pins, which simplifies PCB routing when multiple communication interfaces must coexist on a 16-pin package. The /NVAO suffix designates this variant as automotive-grade AEC-Q100 qualified and supplied on tape-and-reel in a VQFN package. Typical applications include automotive body controllers, LIN nodes for sensor and actuator interfacing, low-power IoT sensor endpoints, white-goods user-interface boards, and battery-powered consumer devices. The 16-VQFN (4x4 mm) footprint suits space-constrained modules, while PPS, CIPs, and XLP enable the device to remain in sleep mode for extended periods while still responding to asynchronous events without CPU wake-up overhead. When designing with this part, place a 0.1 uF decoupling capacitor within 2 mm of the VDD pin and bond the exposed pad to a contiguous ground copper pour for thermal dissipation and signal integrity. Programming is supported by Microchip's MPLAB X IDE and the PICkit or Snap in-circuit programmers; the device can also self-program via bootloader code stored in Flash. AEC-Q100 qualification makes the /VAO variant suitable for under-hood and cabin automotive electronics with operating temperatures from -40C to +125C. This page consolidates distributor pricing, same-family drop-in alternatives, application notes, and design guidance that complement the manufacturer datasheet to accelerate design-in and qualification decisions.

Cotización Contacto

PIC16F15324-E/SL

PIC16F15324-E/SL - 8-bit MCU, 7KB Flash, 32MHz, SOIC-14

The Microchip PIC16F15324-E/SL is an 8-bit PIC microcontroller built on the enhanced mid-range core, delivering 32 MHz CPU performance with 7 KB (4K x 14 words) of self-programmable Flash program memory, 512 bytes of SRAM, and no on-chip EEPROM. It is housed in a 14-pin SOIC package (SL suffix) and operates from 2.3 V to 5.5 V across the -40 °C to +125 °C extended industrial temperature range. An 8-bit microcontroller (MCU) is a small, low-power computer-on-a-chip that integrates a CPU, memory, and peripherals (timers, ADC, communications) on a single die. The PIC16F15324 belongs to the Microchip PIC16F family, which sits in the broader hierarchy of microcontroller -> embedded controller -> semiconductor device. The 8-bit architecture is purpose-built for deterministic, interrupt-driven control tasks where low cost, simple instruction sets, and ultra-low standby current outweigh the need for higher arithmetic throughput. Key features include four Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), two EUSART modules supporting LIN/IrDA, SPI, and I²C (master/slave), four 10-bit PWMs, an 11-channel 10-bit ADC, a 5-bit DAC, two comparators, and eXtreme Low-Power (XLP) technology with a deep-sleep current under 50 nA typical. The device family is described as 'Intelligent Analog with Core Independent Peripherals' by Microchip, meaning complex sequencing can be done in hardware without CPU intervention. Architecturally, the part uses a Harvard RISC design with a 14-bit instruction word, a single-cycle multiplier, and a 31-level hardware stack. The CIP block (CLC + CWG + NCO + PWM + ADC + DAC) lets designers build state machines, waveform synthesizers, and signal-conditioning chains that run autonomously. The XLP nanoWatt XLP peripherals (RTC, WDT, BOR) target battery-sustained applications. Typical uses include sensor nodes, IoT end-points, low-cost motor/PWM drivers, LED lighting controllers, smart-home appliances, battery chargers, consumer white goods, and small human-machine interface (HMI) panels. The 14-pin SOIC footprint is friendly to hand-soldering and traditional through-hole-style manufacturing. When designing with this part, select an MPLAB X IDE project with the XC8 compiler and configure configuration-word fuses for oscillator, watchdog, brown-out reset, code protection, and LVP. Always place a 100 nF decoupling capacitor within 3 mm of VDD and reserve an ICSP header on every prototype for in-circuit programming and debugging.

Cotización Contacto

PIC16F15324-E/SLVAO

PIC16F15324-E/SLVAO - 8-bit 32MHz 7KB Flash MCU 14-SOIC | Microchip

The Microchip Technology PIC16F15324-E/SLVAO is an 8-bit PIC microcontroller from the PIC16F153xx family featuring 7KB (4K x 14 words) of Flash program memory, 512 bytes of SRAM, and 0 bytes of EEPROM. It operates at up to 32 MHz on the enhanced mid-range PIC16 core with an internal oscillator, and integrates Intelligent Analog peripherals, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology. Housed in a 14-pin SOIC package, the automotive-grade "VAO" suffix designates parts qualified to Microchip's automotive quality flow. An 8-bit microcontroller (MCU) is a small, self-contained computing element that integrates a CPU, RAM, non-volatile program memory, and peripherals onto a single silicon die. It belongs to the broader hierarchy: microcontroller -> embedded processor -> semiconductor -> integrated circuit. PIC microcontrollers are widely used in cost- and power-sensitive embedded systems where deterministic real-time behaviour and low part count are priorities. The PIC16F153xx family combines traditional PIC simplicity with modern analog and CIP blocks. Key features include four 10-bit PWM outputs, a comparator, a 5-bit/8-bit DAC, a 10-bit ADC with computation, a Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC), and two Enhanced USART peripherals supporting SPI and I²C. The XLP variants deliver nanoWatt sleep currents, making the part attractive for battery-powered and always-on designs such as sensor nodes and remote controls. Architecturally, the device combines a RISC Harvard-style CPU with on-chip debug, a wide operating voltage range of 2.3 V to 5.5 V, and flexible clocking from internal 32 MHz HFINTOSC down to 31 kHz LFINTOSC. Its CIPs (CLC, CWG, NCO, PWM) execute logic without CPU intervention, offloading timing-critical tasks and reducing firmware complexity. Typical applications include automotive body electronics, sensor signal conditioning, LED lighting controllers, low-power IoT edge nodes, and general-purpose user-interface boards. The combination of analog integration and XLP makes it especially well suited to mixed-signal nodes that must sleep deeply and wake on analog thresholds. When designing with this part, place decoupling capacitors (100 nF plus 1 µF) close to VDD/VSS, route the MCLR line carefully if used, and confirm the SOIC-14 footprint matches your PCB land pattern. Always verify the "VAO" automotive flow acceptance against your project's PPAP and quality requirements.

Cotización Contacto

PIC16F15324-E/ST

PIC16F15324-E/ST - 8-bit MCU, 7KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15324-E/ST is an 8-bit PIC microcontroller built on the enhanced mid-range core, delivering 32MHz CPU speed with 7KB Flash, 512B SRAM, and 256B EEPROM in a 14-pin TSSOP package. The -E temperature grade indicates an extended industrial operating range of -40C to +125C, making the part suitable for harsh-environment embedded designs. The device integrates rich on-chip analog and digital peripherals including a 10-bit ADC, two 8-bit DACs, comparators, four 16-bit PWMs, CWG, four CLC blocks, and two EUSART/SPI/I2C interfaces. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and configurable peripherals. Within the semiconductor hierarchy, MCUs sit inside the broader integrated circuit (IC) family, are classified as embedded processors, and specifically the PIC16F15324 belongs to Microchip's PIC16 mid-range 8-bit MCU family. The 8-bit PIC architecture is widely adopted for cost-sensitive, deterministic, low-power applications such as sensor nodes, appliance controls, and battery-powered IoT devices. Key features of the PIC16F15324 include the eXtreme Low-Power (XLP) technology with deep-sleep currents in the nanoampere range, Core Independent Peripherals (CIPs) that offload tasks from the CPU, and Intelligent Analog peripherals including a 10-bit ADC with computation (ADC2), two 8-bit DACs, and zero-cross detection. The four Configurable Logic Cells (CLCs) allow hardware-level custom glue logic without software overhead, while the Complementary Waveform Generator (CWG) simplifies motor and lighting drive topologies. Technically, the device supports 1.8V to 5.5V operation (F-version), offers up to 32MHz internal oscillator operation, and provides 12 I/O pins with interrupt-on-change capability. The 14-bit instruction word and 8-level hardware stack reflect the classic PIC16 mid-range architecture, ensuring deterministic interrupt latency suitable for real-time control loops. Internal voltage reference and temperature indicator support additional analog housekeeping functions without external components. Typical applications include IoT sensor nodes, low-power wireless nodes, LED lighting controllers, small motor and fan controls, battery chargers, home appliance user interfaces, and remote controls. The extended -40C to +125C temperature range enables deployment in automotive under-hood, industrial sensor, and outdoor equipment environments. The compact TSSOP-14 footprint allows placement on space-constrained boards while still exposing the full peripheral set. When designing with the PIC16F15324-E/ST, ensure decoupling capacitors (100nF plus 1uF bulk) are placed within a few millimeters of VDD/AVDD, and that the MCLR pin is properly pulled-up through a resistor if in-circuit serial programming (ICSP) is needed. Configure unused I/O pins as outputs with logic low to minimize power consumption in deep sleep. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC16F15324-I/JQ

PIC16F15324-I/JQ - 8-bit MCU 7KB Flash 32MHz UQFN-16 | Microchip

The Microchip Technology PIC16F15324-I/JQ is an 8-bit PIC microcontroller featuring 7KB (4K x 14 words) of self-read/write Flash program memory, 512 bytes of SRAM, and a maximum CPU clock of 32 MHz, housed in a 16-pin UQFN (4x4 mm) package. It belongs to the PIC16(L)F153xx family that integrates Intelligent Analog peripherals, Core Independent Peripherals (CIPs) such as CLC and CWG, and eXtreme Low-Power (XLP) modes for energy-constrained designs. What is a PIC 8-bit microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and peripherals on one die. The PIC16F family uses Microchip's enhanced mid-range core with 49 instructions, 16-level hardware stack, and Peripheral Pin Select (PPS) for flexible signal routing. Within the semiconductor taxonomy, an MCU sits under microcontroller -> embedded processor -> digital IC -> integrated circuit. The 8-bit data path prioritizes deterministic real-time response, low cost, and ultra-low standby current over raw arithmetic throughput. Key features include a 10-bit ADC with up to 11 channels, a 5-bit DAC, two comparators, four 10-bit PWMs, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), two EUSART (LIN-capable) modules, and I2C/SPI peripherals. Brown-out Reset (BOR), Power-on Reset (POR), and Peripheral Module Disable (PMD) reduce active and sleep currents to nanoampere levels, enabling years of operation from a single coin cell. Architecture-wise, the device pairs the enhanced mid-range core with hardware multiplier support, DMA-free CIP blocks, and PPS that remaps most digital peripherals to nearly any I/O pin. The internal 32 MHz oscillator eliminates the external crystal in cost-sensitive layouts while still allowing an external oscillator reference for timing-critical UART or LIN-bus stacks. Typical applications include IoT sensor nodes, wearable health bands, battery-powered remote controls, LIN slave nodes in automotive body electronics, low-cost PWM fan or LED controllers, and small appliance user interfaces. The wide 1.8V-5.5V VDD range and XLP nanoWatt sleep modes directly address battery and energy-harvesting designs. When designing with this device, always read the latest Microchip device datasheet and errata before committing layout. Place a 0.1 uF decoupling capacitor within 3 mm of VDD, keep analog AVSS/AVDD traces short, and leave at least one NC-tolerant pin free for PPS remapping flexibility. This page combines manufacturer specifications, distributor pricing tiers, and drop-in same-package alternatives so engineers can compare, qualify, and source the PIC16F15324-I/JQ faster than datasheet-only review.

Cotización Contacto

PIC16F15324-I/P

PIC16F15324-I/P - 8-bit 32MHz 7KB Flash MCU 14-DIP | Microchip

The Microchip Technology PIC16F15324-I/P is an 8-bit PIC16 enhanced mid-range microcontroller delivering 32 MIPS performance with 7KB Flash program memory, 512 bytes SRAM and 256 bytes EEPROM in a 14-pin PDIP package. The -I/P suffix denotes the industrial temperature grade (-40C to +85C) in through-hole PDIP form factor with 32 MHz maximum CPU clock frequency. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path and Harvard architecture, typically used to read sensors, drive actuators, and run embedded control firmware in cost- and power-sensitive applications. The PIC16F15324 belongs to the PIC16 (L)F153xx family of eXtreme Low-Power (XLP) MCUs, occupying a hierarchy of: MCU -> microcontroller -> embedded controller -> semiconductor IC. The device integrates Core Independent Peripherals (CIPs) such as CLC, CWG, NCO and PWM, plus Intelligent Analog including a 10-bit ADC with computation, a 5-bit DAC, and a comparator, enabling sensor and power-conversion loops without CPU intervention. Key features include 7KB self-read/write Flash, 4x 10-bit PWM outputs, 2x EUSART, SPI/I2C, Peripheral Pin Select (PPS) for flexible signal routing, Peripheral Module Disable (PMD) for current budgeting, and XLP IDLE/DOZE modes that drop active current into the microamp range. The 14-pin device exposes up to 12 I/O pins with 11 ADC channels. A 32 kHz to 32 MHz internal oscillator plus PLL eliminates external crystals in many designs. Typical applications include low-power IoT sensor nodes, battery-powered consumer devices, home appliances, LED lighting controllers, and general-purpose embedded control where small package, low quiescent current, and rich analog integration outweigh raw CPU throughput. Designers should budget I/O: only 12 of 14 pins are usable I/O on the 14-pin variant, so verify signal mapping against the pinout before committing to PCB layout. Decouple VDD with at least 100 nF and a bulk 1-10 uF tantalum or aluminum polymer capacitor close to the pins for reliable ADC and core operation. This page synthesizes distributor pricing, drop-in alternatives and engineering design notes that go beyond the manufacturer datasheet to accelerate board bring-up and BOM decisions.

Cotización Contacto

PIC16F15324-I/SL

PIC16F15324-I/SL - 7KB Flash 8-bit MCU, 32MHz, 14-SOIC | Microchip

The Microchip Technology PIC16F15324-I/SL is an 8-bit PIC microcontroller built on the enhanced mid-range core with 49 instructions, 16 stack levels, and 32 MHz maximum CPU performance, integrating 7 KB self-write flash program memory, 512 B SRAM, and zero data EEPROM in a 14-pin SOIC (SL) package. The part is qualified across the industrial temperature range of -40C to +85C and supports a wide 2.3 V to 5.5 V operating voltage range, making it directly compatible with both 3.3 V and 5 V system rails common in industrial, consumer, and battery-powered designs. An 8-bit microcontroller is a single-chip computer whose internal data path is 8 bits wide; it sits in the broader taxonomy of microcontrollers -> microprocessors -> semiconductors. 8-bit MCUs remain dominant in cost-sensitive, deterministic, low-power applications such as sensor nodes, household appliances, and human-interface boards. Within Microchip's portfolio, the PIC16F153xx family is positioned at the intersection of Core Independent Peripherals (CIPs) and Intelligent Analog integration, providing hardware state-machine behavior without CPU intervention, and belongs to the broader PIC16 (L)F153XX 8-bit product family that combines eXtreme Low-Power (XLP) operation with rich analog and communication peripherals. Key features include 4 Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), two Enhanced USART peripherals supporting SPI/I2C, 4 PWM channels, a 10-bit ADC, a 5-bit DAC, two comparators, and Peripheral Pin Select (PPS) for flexible signal routing. The 14-pin SOIC footprint preserves board compatibility with legacy 8-bit designs while exposing the rich peripheral mix of the newer generation. PPS in particular lets designers remap digital peripheral I/O onto almost any general-purpose pin, simplifying PCB layout and BOM reuse across SKUs. Architecturally, the PIC16F15324 combines a Harvard-style enhanced mid-range CPU with Intelligent Analog peripherals and Core Independent Peripherals, allowing the device to handle complex timing and signal conditioning tasks without CPU wake events - a hallmark of modern low-power embedded design. The 32 MHz core delivers approximately 8 MIPS, and the CWG can synthesize complementary dead-time-controlled outputs for half-bridge FET driving, while the 4xCLC blocks implement custom combinational/sequential logic that runs independently of the core. Typical applications include low-power IoT sensor endpoints, battery-powered consumer devices, LED lighting controls, e-metering sub-systems, and general-purpose digital interfaces. The wide voltage range and rich peripherals also suit industrial Human-Machine Interface (HMI) boards, remote-control units, and small appliance mainboards where the SL (SOIC-14) footprint is preferred for hand-soldering during prototyping. When designing with this MCU, prioritize PPS assignments early in schematic capture to avoid rework, and verify that active peripherals are individually disabled through PMD (Peripheral Module Disable) registers before entering sleep to minimize quiescent current into the sub-uA range. The 14-SOIC footprint simplifies hand-soldering and rework during prototyping, but for high-volume production the TSSOP or UQFN variants in the same family are typically preferred. This page synthesizes distributor pricing, drop-in same-family alternatives, design considerations, and pin-compatible cross-reference information that is not assembled in any single manufacturer document or distributor listing.

Cotización Contacto

Subcategorías

Productos (38.000+)

PIC16F15276-I/PT - 28KB Flash 8-bit MCU, 32MHz, 44-TQFP | Microchip

PIC16F1527T-I/PT - 8-bit 20MHz MCU 28KB Flash 64-TQFP | Microchip

PIC16F15313-E/RF - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip

PIC16F15313-E/SN - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F15313-E/SNVAO - 8-bit MCU, 3.5KB Flash, 32MHz, AEC-Q100 | Microchip

PIC16F15313-I/P - 8-bit MCU, 3.5KB Flash, 32MHz, XLP | Microchip

PIC16F15313-I/RF - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F15313-I/SN - 8-Bit 32MHz MCU, 3.5KB Flash | Microchip

PIC16F15313T-I/SN - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F15323-E/JQ - 8-bit MCU 3.5KB Flash 32MHz XLP | Microchip

PIC16F15323-E/SL - 8-bit MCU, 3.5KB Flash, 32MHz, 14-SOIC | Microchip

PIC16F15323-E/ST - 8-Bit 32MHz MCU, 3.5KB Flash, XLP | Microchip

PIC16F15323-I/JQ - 8-bit MCU, 3.5KB Flash, 256B RAM | Microchip

PIC16F15323-I/P - 8-bit MCU, 3.5KB Flash, 32MHz, 14-PDIP | Microchip

PIC16F15323-I/SL - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

PIC16F15323T-I/SL - 8-bit 32MHz XLP MCU, 3.5KB Flash | Microchip

PIC16F15323T-I/ST - 8-Bit 32MHz MCU 3.5KB Flash 14-TSSOP | Microchip

PIC16F15324-E/7NVAO - 7KB Flash MCU, 32MHz, 16-VQFN | Microchip

PIC16F15324-E/SL - 8-bit MCU, 7KB Flash, 32MHz, SOIC-14

PIC16F15324-E/SLVAO - 8-bit 32MHz 7KB Flash MCU 14-SOIC | Microchip

PIC16F15324-E/ST - 8-bit MCU, 7KB Flash, 32MHz | Microchip

PIC16F15324-I/JQ - 8-bit MCU 7KB Flash 32MHz UQFN-16 | Microchip

PIC16F15324-I/P - 8-bit 32MHz 7KB Flash MCU 14-DIP | Microchip

PIC16F15324-I/SL - 7KB Flash 8-bit MCU, 32MHz, 14-SOIC | Microchip