Circuitos integrados

PIC32CM5164LS00100-I/PF

PIC32CM5164LS00100-I/PF - 512KB Flash Cortex-M23 MCU | Microchip

The Microchip PIC32CM5164LS00100-I/PF is a 32-bit ARM Cortex-M23 microcontroller from the PIC32CM LS00 family, delivering 48 MHz CPU performance with 512 KB Flash, 64 KB SRAM and 8 KB EEPROM in a 100-pin TQFP (14x14 mm) package. The device integrates ultra-low-power techniques including SleepWalking peripherals, Arm TrustZone security, and enhanced touch hardware for HMI designs. A microcontroller (MCU) is a single-chip computer that combines a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and configurable peripherals (GPIO, timers, ADC, communication interfaces) on one die. Within the embedded hierarchy, this PIC32CM part sits in the ultra-low-power 32-bit MCU tier, above 8-bit PIC MCUs and below high-performance Cortex-M4/M7 application processors. The Cortex-M23 core targets the lowest active power per MHz while keeping a Thumb-2 instruction set and TrustZone-M isolation. Key features include 80 general-purpose I/O, a 1.62 V to 3.63 V supply range, on-chip 12-bit ADC, multiple SERCOM (USART/SPI/I2C) channels, a hardware cryptographic module, and a peripheral touch controller that offloads touch scanning from the CPU. The LS suffix denotes the security-enhanced variant, while the LS00 sub-family emphasizes energy harvesting-ready sleep modes with sub-microamp standby currents. Technically, the die pairs a Cortex-M23 core with Microchip's proprietary SleepWalking event fabric, allowing peripherals to wake the core only on qualified events. TrustZone-M partitions Flash and SRAM into secure/non-secure regions for firmware IP protection, useful in connected-node applications. Typical applications include IoT end nodes, secure authentication tokens, low-power wireless sensor hubs, smart-home touch panels, industrial HMI keypads, and battery-powered metering. The 100-pin TQFP exposes enough I/O for color TFTs and parallel sensor buses. When designing, budget decoupling capacitors per the supply-rail count and verify SleepWalking event configuration against your wake-up latency budget. This page synthesizes distributor pricing, drop-in PIC32CM family alternatives, and practical design notes not consolidated in the Microchip datasheet.

Cotización Contacto

PIC32CM5164LS60048-I/U5B

PIC32CM5164LS60048-I/U5B - 512KB Flash Cortex-M23 MCU | Microchip

The Microchip Technology PIC32CM5164LS60048-I/U5B is a 32-bit secure Arm Cortex-M23 microcontroller with 512KB Flash and integrated Trust Platform security (ATECC608), housed in a 48-pin VQFN package with exposed pad. It operates from 2.0V to 3.63V at up to 48 MHz, delivering 2.64 CoreMark/MHz and 1.03 DMIPS/MHz efficiency. The device integrates ultra-low-power SleepWalking peripherals, Arm TrustZone technology, and immutable secure boot for hardened IoT edge nodes. A microcontroller (MCU) is an integrated circuit that combines a CPU core, memory (Flash, SRAM), and programmable peripherals on a single die. Cortex-M23 is an Armv8-M Baseline architecture core optimized for energy efficiency and deterministic interrupt response in deeply embedded applications. Within the system hierarchy, this part sits at the MCU level: MCU -> embedded microcontroller -> semiconductor IC. The LS60 family is Microchip's top-tier PIC32CM variant, adding hardware cryptography and secure element integration on top of the standard LS00 feature set. Key features include 512KB Flash, 64KB SRAM, up to 48 MHz CPU speed, integrated ATECC608 secure element, TrustZone for Cortex-M, secure boot with immutable root of trust, SleepWalking peripherals, PTC (Peripheral Touch Controller) for capacitive touch, and a 12-bit 1 Msps ADC with up to 16 channels. The device also supports up to 6 SERCOM (serial communication) interfaces configurable as I2C/SPI/UART, and integrates a 24-bit Sigma-Delta ADC option for precision sensing. Architecturally, the LS60 family uses a low-leakage process technology combined with multiple low-power modes (IDLE, STANDBY, BACKUP, OFF) and event-driven SleepWalking that wakes the CPU only when a peripheral requires service. This enables years of battery life on coin-cell powered IoT endpoints. The 48-pin VQFN package with exposed pad supports efficient thermal dissipation for continuous-duty industrial applications. Typical applications include secure IoT endpoints, smart home and building automation, smart metering, electronic locks and access control, wireless sensor nodes, medical wearables, secure payment terminals, and industrial HMI with touch. TrustZone plus ATECC608 make it especially suited to any application requiring certificate-based authentication, secure firmware update, and protection against physical tamper. Design consideration: when migrating from LS00 to LS60, verify that TrustZone-aware firmware and ATECC608 provisioning are integrated into your secure-boot chain, otherwise the security features cannot be exercised. Plan for an extra I2C or GPIO to interface to the secure element during provisioning. This page synthesizes distributor stock signals, same-family pin-compatible variants, cross-brand benchmarks, and practical low-power design notes not collected on a single manufacturer page.

Cotización Contacto

PIC32CM5164LS60048T-I/U5B

PIC32CM5164LS60048T-I/U5B - Secure Cortex-M23 MCU, 512KB Flash | Microchip

The Microchip Technology PIC32CM5164LS60048T-I/U5B is a 32-bit secure microcontroller built on the Arm Cortex-M23 processor core with 512 KB of Flash and 64 KB of SRAM, housed in a 48-pin VQFN package with an exposed thermal pad. The PIC32CM LS60 family integrates hardened security features including Trust Platform ATECC608, Arm TrustZone technology, immutable secure boot, and secure key storage, while delivering ultra-low-power operation, advanced touch sensing, and smart analog integration in a single device. A secure MCU is a microcontroller that integrates hardware root-of-trust, cryptographic accelerators, secure boot, and tamper detection directly into the silicon so that firmware, keys, and runtime data can be protected against physical and remote attacks. Secure MCUs belong to the broader category of microcontrollers within the embedded processor hierarchy, sitting between general-purpose MCUs and dedicated security ICs such as TPMs and SE chips. They are essential in IoT and edge devices where the device identity, firmware integrity, and credential storage cannot be left to software alone. Key features include a Cortex-M23 core running up to 48 MHz, 512 KB of Flash program memory, 64 KB of SRAM, an integrated ATECC608 Trust Platform, Arm TrustZone for Cortex-M, secure boot with immutable root of trust, multiple low-power modes with SleepWalking peripherals, an advanced touch controller supporting self- and mutual-capacitive sensing, a 12-bit ADC, op-amps, DACs, and comparators, plus USB and SERCOM interfaces. These features enable connected, touch-enabled products that must meet modern IoT security requirements without sacrificing energy efficiency. The architecture pairs an ARMv8-M baseline core with single-cycle I/O access and a peripheral event system that allows autonomous data movement between ADC, DAC, and crypto blocks without CPU intervention, lowering active current and reducing wake cycles. Security logic, signal chain integrity, and analog subsystems share a low-noise internal voltage rail, which improves ADC SNR and stabilizes touch measurement under dynamic load. Typical applications include secure IoT end nodes, smart locks and access control, smart home hubs with touch panels, connected health wearables, industrial sensor nodes with signed firmware, and Matter/Thread/Zigbee edge devices. Designers favor this part when an integrated secure element, low power, and capacitive touch are all required in a compact 48-pin QFN footprint. When designing with this device, allocate PCB area for the exposed thermal pad and provide direct solder connection to the inner ground plane for heat spreading. Place the ATECC608 I2C lines as short as possible to the MCU and add 4.7 kohm pull-ups to the host supply; for USB, the internal pull-up and D+/D- traces must be 90 ohm differential and length-matched.

Cotización Contacto

PIC32CM5164LS60064-I/5LX

PIC32CM5164LS60064-I/5LX - 512KB Flash Cortex-M23 MCU with TrustZone | Microchip

The Microchip Technology PIC32CM5164LS60064-I/5LX is a 32-bit ARM Cortex-M23 microcontroller from the PIC32CM LS60 family, integrating 512 KB Flash and 64 KB SRAM in a 64-pin VQFN (5LX) package with hardened security and ultra-low-power peripherals. It operates from 2.0V to 3.63V at up to 48 MHz core clock across -40C to +85C, delivering 2.64 CoreMark/MHz and 1.03 DMIPS/MHz with single-cycle hardware multiplier, hardware divider, NVIC and Memory Protection Unit. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile memory (SRAM), non-volatile memory (Flash), and a rich set of peripherals such as timers, communication interfaces, ADC/DAC, and GPIO. Within the broader semiconductor hierarchy, an MCU sits between a microprocessor (MPU, which requires external memory and peripherals) and a system-on-chip (SoC, which adds application-specific accelerators). The Cortex-M23 core specifically targets low-power, deterministic embedded applications that benefit from the ARMv8-M baseline architecture, including TrustZone for ARMv8-M and the Cortex-M23 instruction subset, while preserving bit-band-free deterministic interrupt latency. Key features of the PIC32CM5164LS60064 include an integrated Trust Platform ATECC608 secure element, Arm TrustZone for hardware-isolated secure/non-secure firmware domains, immutable root-of-trust secure boot, innovative SleepWalking peripherals that allow I/O and analog blocks to operate autonomously while the CPU remains asleep, industry-leading water-tolerant touch sensing, on-chip op amps, and a 12-bit ADC with up to 1 Msps conversion rate. The device family also integrates DAC, comparators and zero-crossing detectors. Architecturally, the LS60 variant extends the lower-power LE/LS00 line with the embedded ATECC608 secure element and full TrustZone support, enabling secure key storage, ECDSA/Boot verification, and tamper detection. Compared with Cortex-M0+ designs, the M23 adds hardware divide, faster interrupt entry, and deterministic Thumb-only instruction execution, making this part well-suited to IoT edge nodes, secure authentication endpoints, and human-machine-interface panels. Typical applications include secure IoT end nodes, home and building automation controllers, smart appliances with capacitive touch HMIs, wireless sensor hubs pairing with external radios, low-power medical wearables, and industrial HMI panels. When designing with this part, allocate the 64-pin VQFN land pattern early because the 5LX variant is the largest 64-pin option in the family and a smaller 48-pin VQFN (U5B) or 64-pin TQFP (PT) layout would require pin remapping.

Cotización Contacto

PIC32CM5164LS60064-I/PT

PIC32CM5164LS60064-I/PT - 512KB Flash 64KB SRAM Cortex-M23 MCU | Microchip

The Microchip Technology PIC32CM5164LS60064-I/PT is a 32-bit microcontroller from the PIC32CM LS60 family, built around an Arm Cortex-M23 core and packaged in a 64-pin TQFP (PT). It integrates 512 KB Flash and 64 KB SRAM, hardened security (TrustZone for Armv8-M and embedded ATECC608 Trust Platform), ultra-low-power peripherals, superior touch sensing, and smart analog in a single device aimed at connected, secure, battery-aware embedded designs. A 32-bit microcontroller (MCU) is a programmable System-on-Chip that combines a processor core, non-volatile program memory (typically Flash), volatile working memory (SRAM), and a rich peripheral set on one die. Modern MCUs sit at the hierarchy MCU -> embedded controller -> semiconductor. Cortex-M23 specifically is the smallest Armv8-M core with TrustZone security extensions, positioned between Cortex-M0+ (basic) and Cortex-M4 (DSP+FPU), making it ideal for low-power secure IoT endpoints. Key features of this part include 512 KB Flash for firmware, 64 KB SRAM for working data, TrustZone isolation, hardware crypto accelerators via ATECC608, up to 64 KB EEPROM emulation, multiple SERCOM-configurable peripherals (USART, I2C, SPI), 12-bit ADC with up to 16 channels, and integrated touch controller hardware with driven shield support for robust proximity sensing. The 64-pin TQFP offers ample I/O for human-machine interface and mixed-signal designs. Architecturally, the device uses an ultra-low-power architecture featuring multiple sleep modes (IDLE, STANDBY, BACKUP with full RAM retention), an Event System for autonomous peripheral interaction without CPU wake-up, and a Sleepwalking Peripheral System. The integrated ATECC608 Trust Platform provides immutable secure boot, secure key storage, and cryptographic authentication. Typical applications include secure IoT endpoints (TLS-authenticated sensors, smart locks), consumer HMI with touch (appliance panels, smart thermostats), industrial sensor hubs with secure firmware update, battery-powered wearables, and home automation bridges. The combination of low-power sleep modes and TrustZone security makes it especially compelling for always-on edge nodes that must authenticate cloud connections without draining battery reserves. When designing with this part, choose a toolchain from MPLAB X (XC32 compiler) and configure TrustZone from project initialization. Plan the pinout around the integrated touch channels if you intend to use driven shield, and budget Flash/RAM to leave room for a secure bootloader image in the secure region. This page synthesizes distributor availability, parametric drop-in alternatives, and practical design notes beyond the manufacturer datasheet - including pinout, comparison, and TrustZone-aware design tips not always consolidated in the device brief.

Cotización Contacto

PIC32CM5164LS60064T-I/5LX

PIC32CM5164LS60064T-I/5LX - 512KB Flash MCU, Cortex-M23, 64-VQFN | Microchip

The Microchip PIC32CM5164LS60064T-I/5LX is an ultra-low-power 32-bit microcontroller built on the Arm Cortex-M23 core running at up to 48 MHz, integrating 512 KB of Flash and 64 KB of SRAM in a 64-pin VQFN (9x9 mm) package. It belongs to the PIC32CM LS60 family and combines hardened security features (integrated ATECC608 Trust Platform, Arm TrustZone, immutable secure boot, secure debug) with SleepWalking peripherals that wake only the needed subsystem, reducing active-mode current to a fraction of conventional Cortex-M0+ designs. The 'I' temperature grade supports -40C to +85C operation. Background Knowledge - What is a Cortex-M23 microcontroller? A Cortex-M23 microcontroller is a 32-bit MCU IP core from Arm designed for energy-efficient embedded applications; it sits between the older Cortex-M0+ and the more capable Cortex-M4 in the Arm hierarchy, with full Armv8-M Baseline architecture including TrustZone for Cortex-M. The PIC32CM LS60 family extends this with Microchip's proprietary low-power techniques including picoPower, SleepWalking, and Event System. The taxonomy for this part is: 32-bit microcontroller -> Arm Cortex-M MCU -> Cortex-M23 family -> PIC32CM LS60 family -> Microchip PIC microcontroller line. Key features include up to 48 MHz CPU clock, 2.64 CoreMark/MHz performance, 1.03 DMIPS/MHz, single-cycle hardware multiplier, hardware divider, Nested Vector Interrupt Controller (NVIC), Memory Protection Unit (MPU), integrated touch controller and op-amps (smart analog), 2.0V-3.63V supply for LS60 variants, and 5x5 mm to 9x9 mm package options depending on pin count. The LS60 suffix indicates the security-enabled variant with ATECC608 crypto authentication integrated on-die. The architecture pairs a Cortex-M23 core with bus matrix connected to Flash, SRAM, peripherals and the Event System for zero-CPU-overhead peripheral hand-off. SleepWalking allows peripherals to inspect incoming data autonomously and only wake the CPU when relevant events arrive, dramatically reducing average power in IoT sensor nodes. TrustZone for Cortex-M partitions memory and peripherals into Secure and Non-Secure worlds. Typical applications include IoT end nodes (battery-powered sensors), secure connected devices with crypto authentication (smart locks, asset trackers), touch-interface industrial controls, smart home and building automation hubs, medical wearables (low-power BLE body monitors), and secure payment terminals. The combination of low power, integrated crypto, and touch makes it well-suited to edge nodes that must authenticate to a cloud. Design consideration - The 2.0V-3.63V supply range means this MCU cannot be powered directly from a single-cell Li-Ion (4.2V max) without an LDO; pair with a low-Iq regulator such as MCP1700. Decouple VDD with a 100 nF X7R ceramic placed within 3 mm of each power pin group. This page synthesizes distributor pricing, drop-in PIC32CM alternatives, and design notes not found in the standalone manufacturer datasheet, including a same-package comparison versus LS00 (no ATECC608) and LS00 (no security) family variants.

Cotización Contacto

PIC32CM5164LS60064T-I/PT

PIC32CM5164LS60064T-I/PT - 64-Pin MCU, Cortex-M23, 512KB | Microchip

The Microchip Technology PIC32CM5164LS60064T-I/PT is a 32-bit microcontroller from the PIC32CM LS60 family, built on the Arm Cortex-M23 processor core, with 512 KB Flash and 64 KB SRAM, packaged in a 64-pin TQFP (PT) form factor. It integrates the Trust Platform ATECC608 hardware crypto element, Arm TrustZone technology, immutable secure boot, and Microchip's ultra-low-power picoPower architecture, making it suited for hardened IoT endpoints and battery-powered secure applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals. The Cortex-M23 is an Armv8-M Baseline core optimized for energy efficiency with TrustZone security extensions for isolated firmware execution. The PIC32CM LS60 family sits in Microchip's ultra-low-power MCU portfolio, bridging the gap between simple Cortex-M0+ parts and higher-tier Cortex-M4 devices by combining strong security, low power, and smart analog integration in a single die. Key features include a 48 MHz maximum CPU clock, 512 KB Flash, 64 KB SRAM, a 12-bit ADC with up to 16 channels, multiple SERCOM interfaces configurable as UART/SPI/I2C, and PTC (Peripheral Touch Controller) for capacitive touch sensing. The integrated ATECC608 secure element provides hardware-based ECDSA, ECDH, AES-128, SHA-256, and secure key storage, while the TrustZone-aware secure boot enforces immutable root-of-trust at reset. The architecture leverages a Cortex-M23 core with single-cycle multiply and a 2-stage pipeline, balancing deterministic interrupt response with low dynamic current. Multiple low-power modes (Idle, Standby, Backup, and Off) extend battery life to single-digit microampere levels in sleep. Hardware crypto accelerators offload ECC and AES operations from the CPU, enabling faster TLS handshakes at lower energy budgets. Typical applications include IoT end nodes, secure sensor hubs, smart-home devices with touch interfaces, industrial sensor modules, secure access control, and medical wearables. The integrated touch controller and crypto accelerators remove the need for external secure ICs, reducing BOM cost and PCB footprint. Design considerations for this MCU include ensuring the 64-pin TQFP layout supports the required decoupling network (typically 100 nF per VDD pin and 4.7 µF bulk) and that firmware configures TrustZone boundaries correctly to prevent accidental asset lockout. Migration between LS60 family members with different Flash/RAM densities is straightforward because all variants share the same pinout. This page synthesizes Microchip PIC32CM5164LS60064T-I/PT distributor pricing, drop-in replacement alternatives, and practical design notes not consolidated in the manufacturer datasheet alone, accelerating BOM decisions for secure low-power embedded designs.

Cotización Contacto

PIC32CM5164LS60100-I/PF

PIC32CM5164LS60100-I/PF - 48MHz M23 MCU 512KB Flash | Microchip

The Microchip PIC32CM5164LS60100-I/PF is a 32-bit ARM Cortex-M23 microcontroller from the PIC32CM LS60 family, integrating 512 KB Flash and 64 KB SRAM in a 100-pin TQFP package. Operating up to 48 MHz, the device delivers 2.64 CoreMark/MHz and 1.03 DMIPS/MHz, with a 1.62V-3.63V supply range and industrial -40C to +85C temperature grade. The LS60 variant adds hardened security with an integrated Microchip Trust Platform ATECC608 secure element, Arm TrustZone, immutable secure boot, and crypto acceleration. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (ADC, timers, communication controllers). The PIC32CM LS60 belongs to the ultra-low-power Cortex-M23 class, optimized for battery-powered IoT endpoints that need deterministic real-time response plus cryptographic identity for authentication, secure firmware update, and anti-cloning. Within the hierarchy: MCU -> embedded microcontroller -> 32-bit ARM MCU -> Cortex-M23 -> Microchip PIC32CM family. Key features include the integrated ATECC608 secure element (hardware ECC/NIST P-256, secure key storage, ECDH/ECDSA), hardware touch support for capacitive button/slider interfaces, a 12-bit 1 MSPS ADC, two 16-bit DAC channels, four SERCOM-style serial interfaces configurable as UART/SPI/I2C, and a Smart Analog peripheral block. The on-chip Memory Protection Unit (MPU) and TrustZone combine to enforce firmware isolation between secure and non-secure code regions. The LS60 architecture also embeds a SleepWalking peripheral event system, Event System interconnect, and an ultra-low-power RUN/IDLE/STANDYB/STOP/RETENTION/RESET sleep modes family that enables sub-microamp current consumption during duty-cycled sensing, which is critical for coin-cell IoT nodes. Typical applications include secure IoT sensor nodes with authenticated cloud onboarding, capacitive touch user interfaces for white goods and locks, secure medical wearables with encrypted patient data, smart-metering edge nodes, and asset trackers with secure boot and over-the-air firmware updates. Industrial HMI and home-automation keypads also benefit from the integrated touch engine and ATECC608 identity. Designers should budget enough PCB area for a 100-pin TQFP at 14x14 mm (0.5 mm pitch), plan decoupling (100 nF close to each VDD pair plus bulk 4.7 uF), and reserve I/O for the integrated touch channels to fully leverage the MCU's differentiators. Carefully review the secure-element I2C lines - they must remain reachable from the host controller to provision credentials during manufacturing. This page synthesizes distributor pricing, validated drop-in and same-package alternatives, and practical design notes not aggregated on the manufacturer product page.

Cotización Contacto

PIC32CM5164LS60100T-I/PF

PIC32CM5164LS60100T-I/PF - 512KB Flash Cortex-M23 MCU | Microchip

The Microchip Technology PIC32CM5164LS60100T-I/PF is an ultra-low-power 32-bit microcontroller built on the Arm Cortex-M23 core with 512 KB of Flash and 64 KB of SRAM, packaged in a 100-pin TQFP (PF) footprint with industrial -40C to +85C temperature rating. Key features include an integrated Trust Platform ATECC608 secure element, Arm TrustZone for Cortex-M technology, immutable secure boot, and up to 48 MHz CPU clock with SleepWalking peripherals that keep sensors active while the CPU sleeps. The device also integrates a 12-bit ADC, op-amps, DACs, comparators, and a Cryptographic Accelerator supporting AES, SHA, and RSA operations alongside a true random number generator (TRNG). A microcontroller (MCU) is a compact integrated circuit containing a CPU core, program memory, RAM, and programmable peripherals in a single chip. The PIC32CM LS60 family positions itself within the hierarchy of: microcontroller -> 32-bit MCU -> Cortex-M class MCU -> secure low-power MCU -> IoT/edge security MCU -> semiconductor. Compared to legacy PIC24/PIC32MX parts, Cortex-M23 cores execute the Thumb-2 instruction set and deliver higher code density per MHz. The LS60 family is designed for hardened-security IoT endpoints, smart-home hubs, industrial sensor nodes, and touch-enabled human-machine interfaces. Sleep currents in the microamp range and active mode below 100 uA/MHz make it suitable for battery-powered edge devices that must remain in the field for years. The 100-pin TQFP provides abundant GPIO for parallel displays, capacitive touch matrices, and multiple serial interfaces including SERCOM, I2C, SPI, and CAN-FD. Typical applications include secure IoT nodes with certificate-based authentication, industrial HMI panels with touch and TFT support, low-power wireless sensor nodes, smart meters, and home automation gateways. When designing with this device, reserve adequate PCB area for the TQFP-100 footprint and follow the QSPI/SERCOM routing guidance in the Microchip application notes for best EMC performance.

Cotización Contacto

PIC32CM6408MC00032-E/PT

PIC32CM6408MC00032-E/PT - 64KB Flash 32-bit M0+ MCU | Microchip

The Microchip Technology PIC32CM6408MC00032-E/PT is a 32-bit ARM Cortex-M0+ microcontroller with 64KB Flash, 8KB SRAM, and 2KB EEPROM, running up to 48MHz, housed in a 32-pin TQFP (7x7mm) package. It operates from 2.7V to 5.5V, with 26 general-purpose I/O pins, integrated motor-control peripherals (12-bit ADC, 16-bit Sigma-Delta ADC, 10-bit DAC), SERCOM modules, and LIN support. The device is AEC-Q100 qualified for automotive, consumer, commercial, and industrial motor-control applications in electrically noisy environments. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory (Flash), data memory (SRAM), and peripheral interfaces. The PIC32CM family belongs to the Cortex-M0+ class - the most energy-efficient ARM core - optimized for low power, deterministic interrupt response, and simple C programming. It sits within the hierarchy: ARM Cortex-M0+ -> 32-bit MCU -> microcontroller -> semiconductor -> embedded system building block. The PIC32CM MC sub-family is purpose-built for motor control, integrating analog front-ends and PWM timers optimized for field-oriented control (FOC) of BLDC, PMSM, and stepper motors. Key features of the PIC32CM6408MC00032-E/PT include 48MHz core clock, 64KB Flash with ECC, 8KB SRAM with ECC, 2KB EEPROM, and an operating temperature range of -40C to +125C (extended automotive grade). Integrated motor-control peripherals include a 16-bit Sigma-Delta ADC (ideal for shunt current sensing), a 12-bit ADC, and a 10-bit DAC for analog feedback loops. Communication interfaces include SERCOM (configurable as UART/SPI/I2C), LIN, and I2S. The Cortex-M0+ core uses a 2-stage pipeline and single-cycle I/O port, offering high code density and deterministic behavior. Hardware CRC, a 32kHz low-power oscillator, and Event System enable low-power operation. The 32-pin TQFP package (7x7mm body) provides ample thermal dissipation and easy hand-soldering for prototype work, while the AEC-Q100 qualification supports automotive under-hood and industrial applications. Typical applications include BLDC/PMSM motor control (fans, pumps, e-bikes), HVAC compressor control, automotive body electronics, industrial drives, and consumer appliances. The wide 5V-tolerant supply rail and 125C temperature grade also suit solar inverters and battery-management interfaces. When designing with this MCU, ensure the supply rail decoupling follows Microchip's recommended 100nF + 4.7uF pattern near VDD pins, and route the analog and digital ground planes carefully to avoid injecting switching noise into the Sigma-Delta ADC inputs. Use MPLAB X IDE with Harmony or MCC for peripheral configuration to accelerate development. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that supplement the manufacturer datasheet with selection guidance for motor-control system architects.

Cotización Contacto

PIC32CM6408MC00032-E/RTB

PIC32CM6408MC00032-E/RTB - 48MHz Cortex-M0+ MCU 64KB Flash VQFN-32 | Microchip

The Microchip Technology PIC32CM6408MC00032-E/RTB is an automotive-grade 32-bit ARM Cortex-M0+ microcontroller with 64 KB Flash and 8 KB SRAM, packaged in a 32-pin VQFN (5x5 mm) with an exposed thermal pad and shipped in Tray packaging. The -E temperature variant supports the -40C to +125C extended automotive range and is AEC-Q100 qualified, with the Cortex-M0+ core clocked at 48 MHz for deterministic real-time control. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and programmable peripherals (timers, ADC, communication interfaces) onto one die. The PIC32CM MC00 series is classified within the hierarchy: microcontroller -> 32-bit MCU -> ARM Cortex-M0+ MCU -> motor-control MCU -> automotive AEC-Q100 MCU -> embedded system IC. It sits in Microchip's PIC32CM family of 5V-tolerant Cortex-M0+ parts designed for noisy industrial, commercial and automotive environments. Key features include Cortex-M0+ core running at 48 MHz, 64 KB Flash program memory, 8 KB SRAM, 5V-tolerant I/O, and a rich analog (set of motor-control peripherals such as the Analog Comparator and one toggle among PWM, QEI, and PTC/timer signals), plus SERCOM-configurable USART/SPI/I2C and an LIN-capable UART for automotive networks. The integrated Motor Control PWM, Quadrature Encoder Interface (QEI), and 24-bit signal capture chain along with the 24-bit Analog Comparison and one toggle of the 12-bit ADC provide deterministic field-oriented control of BLDC and PMSM motors in noisy environments. The architecture combines an ARM Cortex-M0+ core with Microchip's SAM-style peripheral bus, giving low interrupt latency (12 cycles typical) and DMA-assisted data movement so the CPU can offload motor-control loop housekeeping. The 5V-tolerant I/O and on-chip LIN transceiver support directly address 12V automotive battery rails when paired with an external transceiver. Typical applications include automotive HVAC blower control, BLDC/PMSM field-oriented motor control (sensored for servo pumps, sensorless for fans), 32V-tolerant I/O and fan pump controller, 24-bit signal capture chain along with 12-bit ADC general-purpose industrial control, and consumer 32V-tolerant I/O and home appliance white-goods motor control. The wide 2.7V to 5.5V supply and 5V I/O are particularly valuable in industrial 24V signal nodes. When designing with this device, ensure the PCB provides a sufficient copper pour under the exposed thermal pad and route the SERCOM lines as impedance-controlled differential pairs if using high-speed SPI. The part is AEC-Q100 qualified so for non-automotive-grade variants the PIC32CM8932LS60100-I/PF counterpart is available. This page synthesizes Microchip distributor pricing, AEC-Q100 automotive-grade variants, drop-in same-package alternatives and 32-pin VQFN same-package microcontrollers, plus practical design notes for 5V Cortex-M0+ motor control systems not collected in the manufacturer datasheet.

Cotización Contacto

PIC32CM6408MC00032-I/PT

PIC32CM6408MC00032-I/PT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip

The Microchip Technology PIC32CM6408MC00032-I/PT is a 32-bit ARM Cortex-M0+ microcontroller designed for motor control and rugged 5V applications, featuring 64 KB Flash, 8 KB SRAM, and 2 KB EEPROM in a 32-pin TQFP (7x7 mm) package. It operates up to 48 MHz with a single-core architecture and provides 26 GPIO pins for peripheral expansion, plus integrated motor control peripherals such as PWM, ADC, and analog comparators. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), working memory (RAM), data EEPROM, and a rich set of on-chip peripherals. In the broader taxonomy, the PIC32CM MC00 family sits under 32-bit microcontrollers, then ARM Cortex-M0+ based MCUs, then microcontrollers, then embedded semiconductors. This 5V-tolerant family is engineered for consumer, commercial, industrial, and automotive use in electrically noisy environments where 3.3V-only parts would be unreliable. Key features include a wide 2.7 V to 5.5 V supply range, hardware LIN support, multiple SERCOM-style serial interfaces (I2C, SMBus, IrDA, RS-485), 12-bit ADC, and a powerful motor control PWM with complementary outputs and dead-band insertion. The device also integrates a true random number generator (TRNG) and supports capacitive touch via the Peripheral Touch Controller (PTC), enabling HMI and motor drive combinations on a single die. Architecturally, the PIC32CM MC00 combines an ARM Cortex-M0+ core licensed from Arm with Microchip's proprietary peripheral set and CIP (Core Independent Peripherals) such as the Event System, Configurable Custom Logic (CCL), and motor-control timer/counter. Designers benefit from the dual ecosystem: the ARM toolchain (CMSIS, GCC, IAR, Keil) for code development, plus Microchip's MPLAB X IDE, MCC code generator, and Harmony framework for middleware and motor-control libraries. Typical applications include BLDC and PMSM motor drives (fans, pumps, appliance compressors), HVAC actuators, e-bike controllers, power tools, automotive body and accessory modules, and industrial sensor hubs. The 5V tolerance and LIN bus support make it a strong fit for cost-sensitive nodes that previously relied on 8-bit MCUs but need Cortex-M0+ compute for field-oriented control (FOC). When designing with this part, allocate the 8 KB SRAM carefully - use the 2 KB EEPROM for non-volatile parameter storage to avoid wear-leveling on Flash, and reserve DMA channels for high-speed ADC-to-PWM data paths in motor loops. The 32-pin TQFP leaves limited analog channel count; choose the 48- or 64-pin variants if more ADC inputs or PWMs are required. This page synthesizes distributor pricing, drop-in pin-compatible alternatives across the PIC32CM MC00 family, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC32CM6408MC00032-I/RTB

PIC32CM6408MC00032-I/RTB - 48MHz 32-VQFN Motor Control MCU | Microchip

The Microchip Technology PIC32CM6408MC00032-I/RTB is a 5V ARM Cortex-M0+ microcontroller in the PIC32CM MC00 family, integrating 64KB Flash, 8KB SRAM, and 2KB EEPROM in a 32-pin VQFN (5x5 mm) package. It runs at up to 48 MHz, supports 2.7V to 5.5V operation, and exposes 26 general-purpose I/O for motor-control and industrial front-ends. The -I suffix denotes the industrial -40C to +85C temperature grade; the RTB suffix indicates tape-and-reel packaging on the 32-VQFN (RTB) footprint. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory, working RAM, and a rich set of peripherals (ADC, timers, communication interfaces) on a single die. PIC32CM MC00 parts sit inside the broader PIC32CM family (32-bit Cortex-M0+), which itself belongs to Microchip's 32-bit PIC32 MCU portfolio. The MC sub-family adds dedicated peripherals for motor-control loops such as PWM, encoder interfaces, and high-speed ADCs, placing these MCUs in the power-management and motor-drive segment of Microchip's product hierarchy. Key features include the SERCOM-configurable serial engine (USART/SPI/I2C), built-in LIN support for automotive body networks, a 12-bit ADC with up to 1 Msps, and multiple 16-bit timers suitable for field-oriented control (FOC) of brushless DC (BLDC) and permanent-magnet synchronous motors (PMSM). The Cortex-M0+ core delivers deterministic interrupt latency and is supported by Microchip's MPLAB X IDE, MPLAB Harmony, and the XC32 toolchain, plus the open-source Keil MDK-Arm environment for migration projects. Typical applications span consumer appliances (small fans, pumps, vacuum robots), commercial HVAC dampers, industrial low-power motor drives, automotive body modules (seat/door/window, LIN nodes), and general-purpose 5V embedded replacements for legacy PIC16/PIC24 designs. The wide 2.7V-5.5V supply range means the part can be powered directly from a USB rail, a 3.3V LDO, or a 5V switching pre-regulator without level shifters on most signals. When designing with this MCU, allocate one SERCOM instance per communication channel and reserve one ADC channel per phase current shunt for FOC firmware. Program Flash endurance is 10k cycles typical; the integrated EEPROM block eliminates external non-volatile storage for parameter retention tasks.

Cotización Contacto

PIC32CM6408MC00032T-I/PT

PIC32CM6408MC00032T-I/PT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip

The Microchip PIC32CM6408MC00032T-I/PT is a 32-bit ARM Cortex-M0+ microcontroller from the PIC32CM MC family, integrating 64 KB of Flash, 8 KB of SRAM and 2 KB of EEPROM, and operating at up to 48 MHz core frequency in a 32-pin TQFP (7x7 mm) package with 26 GPIO. The device is fabricated on a 5V-tolerant CMOS process, runs from a 2.7 V to 5.5 V supply, and includes a dedicated motor-control PWM subsystem, making it targeted at brushless DC (BLDC), permanent-magnet synchronous motor (PMSM) and switched reluctance drives. What is a microcontroller (MCU)? A microcontroller is a single-chip computer containing a CPU core, non-volatile program memory, working RAM, and a rich set of on-chip peripherals such as timers, ADCs, communication interfaces and PWM channels. Within the embedded hierarchy, an MCU sits below microprocessors (MPUs) in integration and is the central building block of virtually every embedded product - from consumer appliances and IoT nodes to industrial automation, automotive body and motor-control modules. The PIC32CM series combines an ARM Cortex-M0+ core (a widely adopted 32-bit architecture from ARM) with Microchip's 5V-tolerant peripherals. Key features of the PIC32CM6408MC00032T-I/PT include its motor-control PWM peripheral (designed for 3-phase field-oriented control), 12-bit ADC with up to 12 channels, multiple SERCOM-style USART/SPI/I2C serial interfaces, and 32 KB of user-configurable Flash for boot/option storage. The device's industrial-grade -40C to +85C temperature range and automotive-targeted peripherals allow it to be deployed in harsh-electrical environments where ESD and conducted noise are common. Compared to legacy PIC16/PIC24 parts, the Cortex-M0+ core offers cleaner toolchain support via GCC, IAR and Keil. From an architectural standpoint, the PIC32CM MC family uses a Harvard bus architecture with separate code and data paths to the Flash and SRAM, plus a tightly coupled EEPROM block for non-volatile data. The motor-control PWM unit supports complementary outputs, programmable dead-time, ADC trigger, and fault inputs, allowing direct interface to a 3-phase gate driver such as the Microchip MCP8024 or dsPIC33 companion parts. Typical applications include 3-phase BLDC/PMSM motor drives (fans, pumps, e-bikes, appliances), HVAC damper and compressor control, industrial servo and stepper control front-ends, automotive auxiliary pumps and fans, and low-cost 5V industrial sensor hubs. The wide 2.7 V to 5.5 V supply range also supports 3.3 V and 5 V mixed-signal designs without level shifters. When designing with this MCU, ensure your PWM switching frequency and dead-time are sized to the chosen MOSFET/IGBT driver. Place the ADC sample-and-hold capacitor close to the MCU and use the dedicated analog VDD/VSS pins; the integrated Cortex-M0+ core simplifies firmware migration from other ARM parts. This page synthesizes distributor pricing, drop-in alternatives, and practical motor-control design notes not always collected in the manufacturer datasheet.

Cotización Contacto

PIC32CM6408MC00032T-I/RTB

PIC32CM6408MC00032T-I/RTB - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip

The Microchip Technology PIC32CM6408MC00032T-I/RTB is a 32-bit ARM Cortex-M0+ microcontroller from the PIC32CM MC family, integrating 64KB Flash and 8KB SRAM, operating at up to 48MHz, and housed in a 32-pin VQFN (5x5 mm) package with industrial -40C to +85C temperature rating. Designed for motor control and noisy-environment applications, the part combines a 5V-tolerant core with the Cortex-M0+ instruction set, providing deterministic performance for real-time control loops. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and I/O onto one die; the Cortex-M0+ is an ARM architecture that emphasizes small footprint, low power, and deterministic interrupt latency, while the PIC32CM MC family is Microchip's 5V-tolerant extension of that core aimed at consumer, commercial, industrial, and automotive nodes where higher-voltage signaling is common. The 'MC' suffix indicates the inclusion of motor-control PWMs, fast ADC, and op-amps optimized for field-oriented control of brushed, brushless DC, and stepper motors. Key features include 64KB on-chip Flash, 8KB SRAM, hardware multiplier and divider, a 12-bit ADC with up to 16 channels, multiple SERCOM-configurable serial interfaces, and integrated PWM channels with complementary outputs and dead-band generation. The 5V-tolerant I/O simplifies interfacing to legacy analog signal chains without external level shifters, and the dedicated PWM/ADC synchronization logic supports center-aligned and edge-aligned switching patterns typical of FOC motor loops. On the architectural side, the device pairs the Cortex-M0+ core (Armv6-M, Thumb/Thumb-2 instructions) with Microchip peripheral IP, including the SERCOM module (re-configurable as UART, SPI, or I2C), a 16-bit timer/counter array, and motor-control PWM with fault inputs. The 32-VQFN package exposes a high-pin-count variant suitable for three-phase motor drive boards, while the 5V-tolerant pads ease industrial bus compliance. Typical applications include BLDC/PMSM motor control, ceiling fans and pumps, appliance motor drives, HVAC actuators, automotive body and LIN nodes, and industrial servo controllers. The wide temperature range and 5V tolerance make the family especially well suited to appliances and 12V/24V industrial subsystems. When designing with this device, plan for a stable 5V or 3.3V supply rail, dedicate the motor-control PWM channels to a three-phase H-bridge gate driver, and use the integrated op-amps for current shunt amplification to keep the BOM small.

Cotización Contacto

PIC32CM6408MC00048-E/U5B

PIC32CM6408MC00048-E/U5B - 64KB Flash Cortex-M0+ MCU w/ Motor Control | Microchip

The Microchip PIC32CM6408MC00048-E/U5B is a 32-bit ARM Cortex-M0+ microcontroller engineered for motor control and noisy-environment applications, integrating 64KB of Flash and 8KB of SRAM in a 48-pin VQFN (7x7 mm) package. The part operates at up to 48 MHz with a single-core architecture and is qualified to AEC-Q100 for automotive deployment. An MCU (microcontroller unit) is a single-chip computer containing a CPU core, program memory (Flash), working memory (SRAM), and a rich set of on-chip peripherals. In the product hierarchy it sits inside the broader class of microcontrollers -> embedded processors -> semiconductor ICs. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for deterministic real-time control with a streamlined instruction set and Thumb-2 support. This PIC32CM MC variant extends the core with motor-control PWMs, 5V-tolerant I/O, and CAN-FD capable peripherals. Key features include 64KB on-chip Flash (64K x 8), 8KB SRAM, 48 MHz max CPU clock, integrated motor-control PWM peripherals, SERCOM-style serial interfaces, and LIN support. The 48-VQFN package offers an exposed thermal pad and compact 7x7 mm footprint, making the part suitable for space-constrained BLDC, PMSM, and stepper drive boards. Architecturally, the PIC32CM MC combines an ARM Cortex-M0+ core with Microchip's PIC-style peripheral set, giving designers a familiar MPLAB X IDE workflow with Cortex-M toolchain support. The 5V-tolerant I/O and AEC-Q100 qualification make it robust against electrical noise typical in automotive and industrial environments. Typical applications include BLDC and PMSM motor controllers, automotive body and comfort modules, industrial sensor nodes, and consumer appliances. The combination of motor-control PWMs, CAN/LIN, and 5V I/O lets a single part serve as the system controller without external glue logic. When designing with this device, ensure the PCB provides adequate copper under the exposed pad for thermal dissipation and that the supply rail is decoupled with 100 nF + bulk ceramic per the datasheet. Review the device errata for any pre-silicon silicon revisions before committing to high-volume production. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a one-stop reference for selection and sourcing decisions.

Cotización Contacto

PIC32CM6408MC00048-E/Y8X

PIC32CM6408MC00048-E/Y8X - 48MHz Cortex-M0+ MCU | Microchip

The Microchip PIC32CM6408MC00048-E/Y8X is a 32-bit ARM Cortex-M0+ microcontroller from the PIC32CM-MC family, featuring 64KB Flash, 8KB SRAM, and a 48MHz core speed in a 48-pin TQFP (7x7 mm) package. It integrates advanced motor control peripherals (PWM, QEI, ADC with hardware triggering) and is AEC-Q100 qualified for automotive, industrial, and commercial applications operating up to 125C. The device is part of Microchip's 5V tolerant PIC32CM series designed for noisy environments. An ARM Cortex-M0+ microcontroller is a low-power, energy-efficient 32-bit processor core featuring a von Neumann architecture with a single-cycle hardware multiplier, Thumb/Thumb-2 instruction support, and tightly coupled peripherals for deterministic embedded control. Within the hierarchy: microcontroller -> MCU -> embedded processor -> semiconductor, the M0+ class is the smallest and most power-efficient ARM core, typically used in cost-sensitive real-time control applications like motor control, sensor hubs, and IoT endpoints. Key features of the PIC32CM6408MC00048 include 64KB Flash program memory, 8KB SRAM, integrated SERCOM configurable as UART/SPI/I2C, a 12-bit ADC with up to 16 channels, multiple 16-bit timer/counters, and motor-control-specific peripherals such as the PWM with complementary outputs and quadrature encoder interface. The 5V tolerant I/O and wide operating voltage range (2.7V-5.5V) make it suitable for industrial and automotive noise environments. Technical depth: the device uses Microchip's proprietary on-chip debug (SWD) and supports MPLAB X IDE plus Harmony 3 framework. The motor-control PWM engine supports edge-aligned, center-aligned, and variable-frequency modes, enabling Field-Oriented Control (FOC) of 3-phase BLDC and PMSM motors. Hardware fault protection (current-limit, over-voltage) integrates without CPU intervention, critical for safety-relevant drives. Typical applications include BLDC/PMSM motor control in appliances and automotive auxiliaries, HVAC fan and pump control, e-bike and small-EV traction, industrial servo drives, and consumer appliances requiring quiet operation. The integrated motor-control peripherals reduce external component count versus discrete MCU + gate-driver architectures. When designing with this MCU, ensure decoupling on VDD/AVDD pairs and provision for the SWD interface to retain in-circuit programming capability. Use the Harmony 3 motor-control framework to accelerate development, but note that core mark-up at 48MHz places performance ceilings on high-end FOC loops. This page synthesizes distributor pricing from LCSC, DigiKey, Mouser, real-time stock indicators, and engineering application notes specific to motor-control design - not found in the manufacturer datasheet alone.

Cotización Contacto

PIC32CM6408MC00048-I/Y8X

PIC32CM6408MC00048-I/Y8X - 48MHz Cortex-M0+ MCU | Microchip

The Microchip Technology PIC32CM6408MC00048-I/Y8X is a 32-bit ARM Cortex-M0+ microcontroller engineered for motor control and robust industrial applications. It integrates 64KB of Flash memory, 8KB of SRAM, and runs at a maximum CPU speed of 48MHz, all housed in a 48-pin TQFP (7x7 mm) package. The device operates across a wide 2.7V to 5.5V supply range and is rated for industrial temperature operation from -40C to +85C. A 32-bit microcontroller is an integrated circuit that combines a 32-bit processor core, program memory (Flash), data memory (SRAM), and a rich set of peripherals on a single silicon die. Within the broader hierarchy, this part is a member of the MCU (microcontroller unit) class of semiconductors, which sits under the Embedded IC family in the larger Power Management and Embedded Systems category. The Cortex-M0+ core used here is instruction-set compatible with the earlier Cortex-M0 and is upward-compatible with Cortex-M3/M4 designs, simplifying software portability. Key features of the PIC32CM6408MC00048-I/Y8X include dedicated motor-control peripherals (PWM, encoder interface, and 12-bit ADC with dedicated sample-and-hold), SERCOM-configurable serial interfaces for UART/SPI/I2C, an on-chip 12-bit ADC, and a Peripheral Touch Controller (PTC). It also features an integrated LIN transceiver interface, making it well suited to automotive body and comfort networks. The architecture combines a deterministic Cortex-M0+ core with Microchip's SAM-style peripheral set, allowing deterministic motor control loops while retaining easy code development in MPLAB X IDE and MPLAB Harmony. The wide 5V-tolerant I/O and 5V supply tolerance simplify interfacing to legacy industrial sensors and actuators without level shifters. Typical applications include BLDC and PMSM motor control (fans, pumps, small appliances), HVAC actuators, industrial sensor nodes, automotive body controllers, consumer appliances with capacitive touch, and LIN-connected slave nodes. According to the PIC32CM MC00 Family Data Sheet, the device family is qualified for consumer, commercial, industrial, and automotive use. When designing with this MCU, ensure adequate decoupling (100nF + 1uF minimum) close to the supply pins, route the analog and digital ground domains separately, and reserve a dedicated trace for the crystal or external clock. The integrated peripherals reduce external BOM cost, but motor-control loops still benefit from a 4-layer PCB with a continuous ground plane. This page synthesizes distributor pricing, same-brand drop-in variants, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC32CM6408MC00048T-I/U5B

PIC32CM6408MC00048T-I/U5B - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

The Microchip PIC32CM6408MC00048T-I/U5B is a 32-bit ARM Cortex-M0+ microcontroller from the PIC32CM MC family, featuring 64KB Flash, 8KB SRAM, and a 48MHz core clock in a 48-pin VQFN (7x7 mm) package with wettable flank leads. It is designed for motor control, consumer, commercial, industrial, and automotive applications operating in electrically noisy environments, and integrates dedicated motor-control peripherals alongside the SERCOM serial-communication module and LIN support. What is a Cortex-M0+ microcontroller? An ARM Cortex-M0+ MCU is an ultra-low-power 32-bit microcontroller core built on the ARMv6-M architecture, optimized for deterministic interrupt response, low active-current draw, and minimal die area. It sits below Cortex-M3/M4 cores in the ARM hierarchy and is widely used as the main processor in motor-control, sensor-interface, and battery-powered embedded designs where simple deterministic control loops dominate the workload. Key features of the PIC32CM6408MC00048T-I/U5B include 64KB of on-chip Flash (64K x 8), 8KB SRAM, a 48MHz maximum CPU clock, and an integrated motor-control peripheral set tailored for field-oriented control (FOC) of BLDC and PMSM motors. The 5V-tolerant I/O and LIN transceiver support make it robust for harsh industrial and automotive buses, while the 48-VQFN (U5B) package with wettable flanks enables reliable automated optical inspection (AOI) on high-volume production lines. Architecturally, the device pairs the Cortex-M0+ core with Microchip's PIC32CM MC motor-control IP, multiple 16-bit timers with PWM, a 12-bit analog-to-digital converter (ADC), and SERCOM instances configurable as USART, I2C, or SPI. This integration eliminates the need for an external motor-control coprocessor, reducing both BOM cost and PCB area in compact variable-frequency-drive designs. Typical applications include BLDC and PMSM motor control (fans, pumps, e-bikes, drones), field-oriented-control compressor drives for HVAC, appliance motor boards, small appliance control, automotive body and accessory ECUs, and industrial sensor-actuator nodes. The wide operating temperature range (industrial -40C to +85C) supports outdoor and under-hood deployments. When designing with this part, allocate sufficient copper area beneath the exposed pad for thermal dissipation, especially in continuous high-current PWM drive stages, and follow Microchip AN2520 motor-control layout guidelines to minimize dv/dt-induced noise on the ADC sense paths. This page synthesizes distributor pricing, parametric proximity to drop-in alternatives, and practical motor-control design guidance not consolidated on any single distributor page.

Cotización Contacto

PIC32CM6408MC00048T-I/Y8X

PIC32CM6408MC00048T-I/Y8X - 64KB Flash ARM Cortex-M0+ MCU | Microchip

The Microchip PIC32CM6408MC00048T-I/Y8X is a 32-bit ARM Cortex-M0+ microcontroller in the PIC32CM MC family, integrating 64KB Flash and 8KB SRAM with dedicated motor-control peripherals in a 48-pin TQFP (Y8X) package. The device is built around the Cortex-M0+ core running at up to 48 MHz and is targeted at 5V-tolerant consumer, commercial, industrial and automotive motor-control applications in electrically noisy environments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and - in the MC family - motor-control PWM and quadrature decoder blocks. MCUs sit at the heart of every embedded system, replacing discrete logic and providing configurable, software-defined control. The PIC32CM MC family inherits Microchip's SAM heritage and combines it with PIC ecosystem familiarity. Key features of the PIC32CM6408MC00048T-I/Y8X include 64KB (64K x 8) Flash, 8KB SRAM, a 32-bit single-core Cortex-M0+ CPU at 48 MHz, and an integrated Peripheral Touch Controller (PTC) supporting capacitive touch sensing. The MC variant additionally provides dedicated motor-control peripherals including a 24-bit motor-control PWM, a quadrature encoder interface, and analog comparators with DAC references for current-shunt sensing, making it a single-chip solution for brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) control. The architecture leverages the Cortex-M0+ v6-M instruction set with a single-cycle IO bus for deterministic GPIO response, and integrates SERCOM-configurable serial interfaces that can be assigned to USART, I2C, or SPI roles. With 5V-tolerant I/O and an operating voltage range of 2.7V to 5.5V, the device interfaces directly to 5V gate drivers and Hall-effect sensors without level shifters. The 48-pin TQFP package provides ample I/O for parallel motor bridges, encoder signals, and CAN/LIN transceivers required for body and industrial control modules. Typical applications include sensorless and sensored BLDC fan and pump controllers, HVAC blower motors, small appliance drives, robotic joint controllers, e-bike traction units, and industrial servo amplifiers. The MC peripherals also suit LED lighting drivers and power-conversion control loops where precise PWM edge placement matters. When designing with this part, designers should add 0.1uF + 10uF decoupling at every supply pin, route the analog AGND and digital GND back to a single star point under the exposed pad, and follow the Microchip AN2685 motor-control layout guide for high-current switching loops to avoid tripping the brown-out detector. This page synthesizes distributor pricing, pin-compatible alternatives, and practical motor-control layout notes not consolidated in the manufacturer datasheet, providing engineers with a one-stop reference for evaluating the PIC32CM6408MC00048T-I/Y8X against competing 48 MHz Cortex-M0+ motor-control MCUs.

Cotización Contacto

PIC32MK0256GPG048-E/7MX

PIC32MK0256GPG048-E/7MX - 32-bit 80MHz MCU, 256KB Flash, 48-VQFN | Microchip

The Microchip Technology PIC32MK0256GPG048-E/7MX is a high-performance 32-bit microcontroller built on the MIPS32 microAptiv core, integrating a single-core 80MHz CPU with DSP and FPU capabilities. The device delivers 256KB of ECC-protected Flash and 64KB of SRAM in a compact 48-pin VQFN (6x6 mm) package with wettable flanks for automated optical inspection. A 32-bit microcontroller (MCU) is an integrated circuit that combines a microprocessor core, program memory (Flash), data memory (SRAM), and programmable peripherals on a single silicon die. Within the broader hierarchy, a 32-bit MCU sits above 16-bit MCUs and 8-bit MCUs in computational capability, and below application-specific SoCs and microprocessors (MPU). The PIC32MK family specifically targets motor control, digital power conversion, industrial automation, and IIoT applications requiring deterministic real-time performance and DSP-grade signal processing. Key features include 120MHz maximum MIPS performance, an integrated single-precision FPU and DSP extensions for efficient signal-processing workloads, a 12-bit ADC with up to 18 analog channels, dual 12-bit DACs, and CAN FD connectivity for industrial networking. The integrated DSP instructions accelerate motor-control loops, digital filtering, and field-oriented control (FOC) algorithms without offloading to a companion DSP chip. The architecture combines a 5-stage pipeline MIPS32 microAptiv core with tightly-coupled SRAM, configurable instruction cache, and a peripheral set mapped through a multi-channel DMA engine. ECC protection on Flash improves reliability in safety-critical applications, while the wettable-flank QFN package enhances solder-joint inspection yield on automotive-grade production lines. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) control, industrial servo drives, solar micro-inverters, digital power conversion, CAN-FD networked sensors, and IIoT edge nodes. The PIC32MK0256GPG048-E/7MX in particular suits compact designs requiring CAN-FD, dual DAC outputs, and 18-channel ADC sampling. When designing with this part, allocate the 80MHz system clock and DSP pipeline carefully - sustained DSP workloads require deterministic interrupt latency. The wettable-flank QFN footprint simplifies AOI inspection but requires proper pad geometry to ensure reliable solder joints on the 0.4mm pitch. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes beyond the manufacturer datasheet, providing a single reference for engineers evaluating the PIC32MK0256GPG048-E/7MX for motor-control and IIoT designs.

Cotización Contacto

PIC32MK0256GPG048T-E/Y8X

PIC32MK0256GPG048T-E/Y8X - 32-bit 80MHz 256KB FLASH MCU | Microchip

The Microchip Technology PIC32MK0256GPG048T-E/Y8X is a 32-bit MIPS32 microAptiv PIC32MK microcontroller featuring 256 KB of ECC-protected Flash program memory, 64 KB of SRAM, and a maximum CPU clock of 80 MHz (the GPG sub-family is the 80 MHz tier, distinct from the 120 MHz MCJ/MCM tiers). It integrates 18 channels of 12-bit Analog-to-Digital Conversion (ADC), 2 channels of 12-bit Digital-to-Analog Conversion (DAC), and a peripheral set targeting general-purpose embedded control. The device is housed in a 48-pin TQFP (7x7 mm) package with an operating voltage range of 2.3 V to 3.6 V and an automotive-grade -40 C to +125 C operating junction temperature window. What is a PIC32MK microcontroller? A PIC32MK MCU is a 32-bit Flash microcontroller built on the MIPS32 microAptiv core from Microchip Technology, positioned within the broader taxonomy as: PIC32MK -> PIC32 family -> 32-bit MCU -> microcontroller -> embedded IC. Compared to traditional 8-bit PIC MCUs, the PIC32MK offers higher computational throughput, larger memory addressing, DSP instructions, and a richer analog/motor-control peripheral set, placing it in the middle of Microchip's 32-bit MCU portfolio between lower-power PIC32MX and higher-end SAM devices. Key features include up to 256 KB Flash with ECC, 64 KB SRAM, 80 MHz core frequency with a 4-stage pipeline MIPS32 core, hardware multipliers for DSP, dual I2C, I2S, SPI, and UART interfaces, and multiple general-purpose timers. The 12-bit ADC supports up to 18 channels with sample-and-hold for multi-channel analog sampling, and the 12-bit DAC provides two channels for waveform generation or bias control without external components. The PIC32MK0256GPG048T-E/Y8X uses the MIPS32 microAptiv core with DSP and microMIPS ISA support, allowing tight C-code density and deterministic interrupt latency. ECC on Flash and SRAM supports functional-safety applications where single-event upsets must be detected, and the integrated dual-bank Flash allows live firmware updates via in-application programming. Internal PLLs and a flexible clock tree support multiple oscillator sources for noise-immune motor-control loops. Typical applications include BLDC/PMSM motor control (FOC), industrial sensor conditioning, building automation, LED lighting control, low-cost HMI panels, USB-to-UART bridges, and automotive body ECUs. The wide temperature range and ECC memory make it especially attractive for automotive body and chassis subsystems and industrial sensor hubs requiring long-term reliability. When designing with this part, allocate adequate decoupling (100 nF + 1 uF bulk) at each VDD/VSS pair, keep ADC traces short, and reserve the analog supply pin pair (AVDD/AVSS) for low-noise analog reference. For motor-control applications, use the dedicated PWM outputs and QEI interface rather than bit-banging to achieve deterministic switching behavior. This page synthesizes distributor pricing, parameter-verified drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Cotización Contacto

PIC32MK0256GPG048T-I/7MX

PIC32MK0256GPG048T-I/7MX - 32-Bit 120MHz MCU, 256KB Flash | Microchip

The Microchip Technology PIC32MK0256GPG048T-I/7MX is a 32-bit MIPS32 microAptiv PIC32MK microcontroller operating at 120 MHz with 256KB of Flash memory and 48-pin VQFN (6x6 mm) package. It belongs to the PIC32MK General Purpose (GPG) sub-family that combines high-performance 120 MHz processing with ECC-protected Flash and a rich peripheral set. The GPG variants are designed for general-purpose embedded designs while sharing the architecture with the motor-control (MCJ) family. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), and integrated peripherals such as timers, ADCs, communication interfaces, and GPIO. 32-bit MCUs occupy the high-performance tier of the embedded hierarchy: microcontroller -> 32-bit MCU -> ARM/MIPS Cortex-class MCU -> application-specific MCU -> system-on-chip. The microAptiv core implements the MIPS32 instruction set and includes DSP extensions and a single-precision FPU on PIC32MK variants. Key features of this part include a 120 MHz CPU with 1.55 DMIPS/MHz performance, 256KB ECC-protected Flash, 32KB SRAM with parity, 12-bit 5 MSPS ADC, up to 6 UART/SPI/I2C channels, multiple PWM outputs suitable for motor control, and 5V-tolerant GPIO with 22 mA source/sink capability. The device supports industrial temperature range -40C to +85C (I-grades) and is offered in the compact 48-pin 6x6 mm VQFN package which suits space-constrained industrial designs. The PIC32MK0256GPG048T-I/7MX uses the MIPS32 microAptiv core with hardware multiply/divide and DSP ASE, paired with a 7-stage pipeline that delivers deterministic interrupt response. The integrated 12-bit ADC and dedicated motor-control PWM make the part a strong fit for mixed-signal applications, while the ECC Flash improves reliability in safety-sensitive industrial systems. The "NO CAN-FD" designation in distributor listings distinguishes this GPG variant from MCJ parts that include CAN-FD peripherals. Typical applications include industrial control boards, IIoT edge nodes, factory automation, BLDC motor control boards, and general-purpose 32-bit embedded platforms. The combination of 120 MHz performance and large Flash also supports protocol stacks such as Modbus, EtherNet/IP gateways, and graphical HMI interfaces. Designers should note the operating voltage range, decoupling requirements around the analog supply pins, and PCB thermal dissipation for the VQFN-48 exposed pad. Programming is supported by MPLAB X IDE with the XC32 compiler and the MPLAB Harmony framework for peripheral configuration. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes not always consolidated on the manufacturer product page or distributor listings.

Cotización Contacto

PIC32MK0256GPG064-E/PT

PIC32MK0256GPG064-E/PT - 32-bit 120MHz MCU, 256KB Flash | Microchip

The Microchip Technology PIC32MK0256GPG064-E/PT is a 32-bit MIPS32 microAptiv PIC microcontroller running at up to 120 MHz, integrating 256 KB of ECC-protected Flash and 64 KB of SRAM in a 64-pin TQFP package. It belongs to the PIC32MK General Purpose (GP) sub-family, designed for motor control, industrial control, and Industrial Internet of Things (IIoT) applications where DSP-class math and high-resolution analog are required. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (typically Flash), volatile working memory (SRAM), and a configurable set of peripherals such as timers, ADCs, communication controllers, and GPIO. The PIC32MK0256GPG064-E/PT sits in the hierarchy: 32-bit MCU -> MIPS32 microAptiv core -> PIC32MK family -> PIC32MK General Purpose (GP) sub-family -> semiconductor. Compared with 8-bit or 16-bit MCUs, a 32-bit core delivers higher MIPS per MHz, native DSP instructions, and larger linear address space, which matters when running motor-control loops, FOC algorithms, or TCP/IP stacks in real time. Key features include 256 KB Flash with error-correcting code (ECC) for Class B safety integrity, 64 KB SRAM, four independent 12-bit ADC pairs capable of 3.2 Msps aggregate conversion, four op-amps and three comparators in the analog front end, and a hardware CryptoEngine (the 'GPG' letter group indicates NO CAN-FD variant). The device supplies 6 UART, 4 SPI, 4 I2C, and USB 2.0 Full-Speed On-The-Go, plus 9 general-purpose 16-bit timers and 4 dedicated PWM generators with 8 outputs. Technically the PIC32MK0256GPG064-E/PT executes the MIPS32 microAptiv instruction set with DSP ASE, single-cycle hardware multiply-accumulate, and a 5-stage pipeline, achieving 1.52 DMIPS/MHz. The dual-rail analog architecture - one pair of 12-bit ADC rails plus dedicated op-amp/comparator analog resources - lets it close a single-shunt or three-shunt FOC loop without an external analog front-end IC, reducing BOM count for motor drives. Typical applications are BLDC/PMSM motor control, industrial automation PLCs, IIoT edge nodes, multi-channel sensor aggregation, and consumer appliances requiring UL/IEC 60730 Class B firmware self-test. The wide -40C to +125C operating range and ECC Flash suit the part to unattended industrial and appliance-class deployments. When designing with this MCU, reserve dedicated analog power and ground pins (AVDD/AVSS) and keep the 12-bit ADC traces short and guarded; ECC Flash does not eliminate read-disturb mitigation needs in long-lifecycle firmware. Pair with Microchip's MPLAB Harmony v3 for the motor-control or TCP/IP stacks and configure the CFGCON register's JTAG bit before first programming to free diagnostic pins. This page synthesizes 2026 distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

Subcategorías

Productos (32784)

PIC32CM5164LS00100-I/PF - 512KB Flash Cortex-M23 MCU | Microchip

PIC32CM5164LS60048-I/U5B - 512KB Flash Cortex-M23 MCU | Microchip

PIC32CM5164LS60048T-I/U5B - Secure Cortex-M23 MCU, 512KB Flash | Microchip

PIC32CM5164LS60064-I/5LX - 512KB Flash Cortex-M23 MCU with TrustZone | Microchip

PIC32CM5164LS60064-I/PT - 512KB Flash 64KB SRAM Cortex-M23 MCU | Microchip

PIC32CM5164LS60064T-I/5LX - 512KB Flash MCU, Cortex-M23, 64-VQFN | Microchip

PIC32CM5164LS60064T-I/PT - 64-Pin MCU, Cortex-M23, 512KB | Microchip

PIC32CM5164LS60100-I/PF - 48MHz M23 MCU 512KB Flash | Microchip

PIC32CM5164LS60100T-I/PF - 512KB Flash Cortex-M23 MCU | Microchip

PIC32CM6408MC00032-E/PT - 64KB Flash 32-bit M0+ MCU | Microchip

PIC32CM6408MC00032-E/RTB - 48MHz Cortex-M0+ MCU 64KB Flash VQFN-32 | Microchip

PIC32CM6408MC00032-I/PT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip

PIC32CM6408MC00032-I/RTB - 48MHz 32-VQFN Motor Control MCU | Microchip

PIC32CM6408MC00032T-I/PT - 48MHz Cortex-M0+ 64KB Flash MCU | Microchip

PIC32CM6408MC00032T-I/RTB - 48MHz Cortex-M0+ MCU, 64KB Flash | Microchip

PIC32CM6408MC00048-E/U5B - 64KB Flash Cortex-M0+ MCU w/ Motor Control | Microchip

PIC32CM6408MC00048-E/Y8X - 48MHz Cortex-M0+ MCU | Microchip

PIC32CM6408MC00048-I/Y8X - 48MHz Cortex-M0+ MCU | Microchip

PIC32CM6408MC00048T-I/U5B - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip

PIC32CM6408MC00048T-I/Y8X - 64KB Flash ARM Cortex-M0+ MCU | Microchip

PIC32MK0256GPG048-E/7MX - 32-bit 80MHz MCU, 256KB Flash, 48-VQFN | Microchip

PIC32MK0256GPG048T-E/Y8X - 32-bit 80MHz 256KB FLASH MCU | Microchip

PIC32MK0256GPG048T-I/7MX - 32-Bit 120MHz MCU, 256KB Flash | Microchip

PIC32MK0256GPG064-E/PT - 32-bit 120MHz MCU, 256KB Flash | Microchip