Circuitos integrados

Subcategorías

📁 ADC/DAC 3.100+ productos 📁 CI amplificadores 1.900+ productos 📁 Códecs de audio 18 productos 📁 CI de audio 2 productos 📁 Reloj y temporización 670+ productos 📁 Comparator ICs 1 productos 📁 DSP 1.100+ productos 📁 CI de adquisición de datos 2 productos 📁 Potenciómetros digitales 4 productos 📁 Controladores y drivers de pantalla 1 productos 📁 FPGA y CPLD 7.300+ productos 📁 CI de interfaz 3.400+ productos 📁 Controladores LED 1 productos 📁 CI lógicos 460+ productos 📁 CI de memoria 870+ productos 📁 Microcontroladores 20.000+ productos 📁 Microprocesadores 4 productos 📁 Controladores de motor 1 productos 📁 Otros 1 productos 📁 Sensor and Detector Interfaces 1 productos 📁 Circuitos integrados especializados 15 productos 📁 Circuitos integrados de vídeo 14 productos

Productos (39.000+)

LM2902DRE4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902DRE4

LM2902DRE4 - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902DRE4 is a quad general-purpose operational amplifier with a 26 V maximum supply, 1.2 MHz gain-bandwidth product, and 2 mV typical input offset voltage, housed in a 14-pin SOIC package. The device contains four independent operational amplifiers designed for a broad range of low-frequency signal-conditioning applications. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier with high input impedance and low output impedance. Its feedback network can configure the device as a voltage amplifier, comparator, buffer, summing amplifier, or active filter. The LM2902 belongs to the operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor hierarchies, making it suitable for common industrial, instrumentation, audio, control, and interface circuits. The LM2902DRE4 provides four amplifier channels in one package, reducing board area and simplifying multi-channel designs. Key characteristics include a typical gain-bandwidth product of 1.2 MHz, 0.5 V/µs slew rate, 0.8 mA typical supply-current drain, and low 2 mV input offset voltage. Its wide operating supply range supports single-supply operation up to 26 V and dual-supply operation up to ±13 V. The architecture supports a broad input common-mode range while maintaining low supply-current consumption independent of supply voltage. These characteristics make the amplifier suitable for battery-powered instrumentation, process-control signals, sensor interfaces, audio preamplification, active filtering, and general-purpose analog systems. Because all four amplifiers operate from common supply pins, board designers can simplify rail distribution and decoupling. Typical applications include four-channel sensor conditioning, low-frequency active filters, audio mixer stages, comparator circuits, industrial control interfaces, and instrumentation amplifiers built from discrete op-amp stages. The 14-pin SOIC package is also practical for through-hole prototype assembly and conventional surface-mount production, while the −40 °C to +125 °C temperature range supports industrial environments. Design carefully around input and output voltage limits, common-mode range, output-current capability, and the load presented by the feedback network. Place supply-bypass capacitors close to the positive and negative supply pins, keep feedback traces short, and verify stability with the actual source and load impedances. The manufacturer datasheet and pin-description table should control PCB and schematic assignments. This page combines the LM2902DRE4 electrical characteristics, package details, drop-in alternatives, comparison parameters, and practical application guidance to support faster component selection and board-level implementation.

Cotización Contacto
LM2902DRG3 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902DRG3

LM2902DRG3 - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902DRG3 is a general-purpose quadruple operational amplifier with four independent amplifiers, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage in a 14-pin SOIC package. The LM2902DRG3 suffix denotes a tape-and-reel shipping configuration. An operational amplifier, or op amp, is a high-gain analog signal-processing component used to amplify voltage differences, buffer sensors, drive analog inputs, and implement feedback-control circuits. The LM2902 belongs to the quad operational-amplifier family within the broader voltage-amplifier and analog-signal-processing semiconductor hierarchy. Its four amplifiers share power-supply pins but have independent input and output connections, allowing one package to implement four related analog functions. The LM2902 operates from single or split supplies over a wide voltage range, making it useful in industrial-control, instrumentation, and audio circuits. Key characteristics include a 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, and approximately 0.8 mA typical supply-current drain. Four frequency-compensated amplifiers support common closed-loop configurations including noninverting and inverting gain, voltage followers, comparators, summing amplifiers, and difference stages. Its 14-pin SOIC package provides a familiar industrial footprint and thermal performance suitable for conventional through-hole assembly workflows. Because each channel is independent, the IC can implement sensor conditioning, signal amplification, active filtering, and control-loop functions on one board. Single-supply operation simplifies designs where the signal remains above ground, while split-supply operation supports bipolar signals centered around zero volts. Typical applications include industrial sensor interfaces, transducers, audio preamplifiers, analog-to-digital converter input conditioning, motor-control support circuits, and general-purpose instrumentation. The wide supply range and low supply-current drain make the device practical in equipment powered from industrial rails or split supplies, provided the absolute maximum operating limits remain respected. Designers should verify input and output common-mode limits for each supply configuration, account for the offset voltage when precision is important, and use stable feedback networks for unity-gain or noise-sensitive applications. PCB placement should keep sensitive input nodes compact, provide an appropriate ground-return path, and avoid placing high-current switching paths close to amplifier inputs. This product page combines the LM2902 family specifications, package information, sourcing guidance, verified drop-in candidates, application examples, and practical design considerations. The comparisons also distinguish package-compatible alternatives from choices that require different qualification, temperature-range, or performance checks before substitution.

Cotización Contacto
LM2902DRG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902DRG4

LM2902DRG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902DRG4 is a four-channel operational amplifier with a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV input-offset specification in a 14-pin SOIC package. Designed for general-purpose signal conditioning, each amplifier can operate from single or dual supplies, supporting a broad range of industrial, instrumentation, control, and analog-interface applications. An operational amplifier is an analog integrated circuit that uses differential feedback to amplify the difference between two input voltages. The LM2902 belongs to the operational-amplifier hierarchy, where it combines transistor-level input and output stages with internal compensation. Each of its four channels can perform amplification, buffering, comparison, summation, differential sensing, or active-filter functions without requiring a separate amplifier for every signal path. The device provides a 1.2 MHz gain-bandwidth product and a 2 mV input-offset specification, making it suitable for moderate-bandwidth precision applications. The 26 V supply capability also supports higher-voltage industrial interfaces than low-voltage rail-to-rail amplifiers. Texas Instruments specifies an operating temperature range from -40°C to 125°C, allowing operation across demanding commercial and industrial environments. The four amplifiers share one package while retaining independent input and output pins, allowing one IC to implement several analog functions. Their typical design role is to operate with feedback networks that establish closed-loop gain and filtering. Because the device is not rail-to-rail by specification, input and output common-mode limits must be checked against the selected supply voltage and signal range before layout release. Typical uses include transducer signal conditioning, low-frequency active filters, sensor amplifiers, industrial control loops, comparator-style threshold circuits, and audio or communications interface stages. The SOIC package also simplifies inspection and rework on through-hole industrial boards while providing a familiar 14-pin land pattern. For a new design, verify the input and output common-mode range, output-current capability, load impedance, and supply operating limits at the intended signal amplitude. Stable feedback and proper decoupling remain important even when the application is a unity-gain buffer, so use the manufacturer pin-description table when assigning PCB tracks. This page organizes the LM2902DRG4 specifications, verified manufacturer references, same-package alternatives, application guidance, and comparison points. It also highlights the practical checks needed to determine whether a candidate replacement is truly pin-compatible rather than merely functionally similar.

Cotización Contacto
LM2902EDR2G - Quad Single-Supply Op Amp, 14-SOIC | onsemi
LM2902EDR2G

LM2902EDR2G - Quad Single-Supply Op Amp, 14-SOIC | onsemi

The onsemi LM2902EDR2G is a single-supply quad operational amplifier that integrates four independent, general-purpose amplifiers into a 14-pin SOIC (PDSO-14) surface-mount package, with input offset voltage specified up to 7000 uV. It is designed for general-purpose signal conditioning, filtering and control tasks on low-voltage rails. A quad operational amplifier is a multi-channel analog building block in which four voltage amplifiers share a common package and power supply. Each channel offers inverting and non-inverting inputs and a single output. The quad configuration lets one part provide four amplifier functions - instrumentation gain stages, active filters, comparators, level shifters or buffer stages - while cutting board area, reducing the number of supply pins and lowering per-channel cost. In the analog signal chain, a quad op amp sits between sensors and converters, inside the family of amplifier ICs and linear analog ICs. Key characteristics of the LM2902EDR2G include four amplifier circuits in one package, a maximum input offset voltage of 7000 uV, single-supply operation, and a low-power general-purpose architecture suited to instrumentation and control designs. The 14-pin SOIC footprint is a widely supported package with good thermal performance, adequate creepage and clearance for 36 V-class class parts, and compatibility with automated assembly and standard SOIC sockets. Internally, the device uses the classic bipolar single-supply topology that has made the LM2902 family a long-lived industry standard: a differential input stage driving a push-pull output stage, with internal compensation that allows stable operation as a unity-gain buffer. Because it is a general-purpose amplifier rather than a precision or rail-to-rail part, the design engineer should treat the input common-mode range, output swing and offset as application-dependent limits rather than rail-to-rail capabilities. Typical applications include transducer and sensor signal conditioning, active low-pass and band-pass filters, motor and actuator control loops, audio pre-amplification in consumer equipment, 4-20 mA loop instrumentation, and general microcontroller analog front ends where a quad amplifier saves board space. When designing around this device, confirm the common-mode input range and output swing against your actual supply voltage, and keep the layout symmetrical so that thermal gradients do not create offset mismatch between the four channels. Decouple each supply pin locally with a short, low-inductance path to the ground plane, and route feedback components away from noisy digital return paths. This page brings together the manufacturer datasheet details, a qualified drop-in alternative set with verified package compatibility, and application-specific design notes that go beyond the parameter table.

Cotización Contacto
LM2902KAVMPWREP - 30V Quad Op Amp | Texas Instruments
LM2902KAVMPWREP

LM2902KAVMPWREP - 30V Quad Op Amp | Texas Instruments

The Texas Instruments LM2902KAVMPWREP is a four-circuit general-purpose operational amplifier designed for single-supply operation from 5 V to 30 V. Each amplifier provides a typical gain-bandwidth product of 1.2 MHz, a typical slew rate of 0.5 V/µs, and a typical input offset voltage of 2 mV. The device is packaged in a 14-pin TSSOP and is rated for operation from -55°C to +125°C. An operational amplifier, commonly abbreviated op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and control voltage signals. Four independent amplifiers share a common power supply within one package, allowing one IC to provide multiple analog signal-chain functions. Within the product hierarchy, this device is a quad operational amplifier, a multi-amplifier IC, and a general-purpose analog signal-conditioning component. The LM2902KAVMPWREP combines a wide 30 V supply capability with four independent, internally frequency-compensated amplifiers. Its 1.2 MHz gain-bandwidth product supports moderate-bandwidth signal processing, while the 0.5 V/µs slew rate provides adequate response for audio-frequency, transducer, and general control applications. The low 2 mV typical offset voltage helps reduce output error in DC-coupled amplifier stages. Improved ESD protection rated at 2 kV is a defining feature of the enhanced-product LM2902KAV family. The four amplifiers can operate from a single 5 V to 30 V supply, or from split supplies when the negative supply remains within the device rating. Internal frequency compensation allows each amplifier to operate as a stable closed-loop stage without external compensation components. Typical uses include industrial sensor conditioning, low-level audio amplification, current-loop interfaces, active filtering, comparators, and four-channel control systems. The extended -55°C to +125°C temperature range makes the device suitable for industrial and high-temperature equipment when combined with appropriate passive components and PCB design practices. When designing a circuit, account for input common-mode range, output swing, load current, and stability at the selected gain. Place input and output decoupling capacitors close to the supply pins, keep feedback paths short, and verify noise behavior with the actual source impedance and surrounding circuitry. This product page combines the manufacturer’s core electrical and environmental specifications with practical PCB guidance, direct replacement options, and application-focused engineering analysis for engineers evaluating the LM2902KAVMPWREP.

Cotización Contacto
LM2902KAVQDRQ1 - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM2902KAVQDRQ1

LM2902KAVQDRQ1 - Quad 30V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902KAVQDRQ1 is a four-circuit, general-purpose operational amplifier specified for a 30 V maximum supply, 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage in a 14-pin SOIC package. The automotive-qualified LM2902-Q1 family is designed for systems requiring four amplifiers per package, extended-temperature operation, and reliable operation across a wide supply range. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2902 contains four independent, internally compensated amplifiers, allowing one package to provide feedback control, buffering, signal conditioning, or differential-to-single-ended conversion. In the power-management hierarchy, it is an analog signal-chain IC rather than a voltage regulator, although its wide supply tolerance makes it useful in industrial and automotive power systems. The headline specifications include four amplifier circuits, a 1.2 MHz gain-bandwidth product, a 0.5 V/us slew rate, and approximately 2 mV offset voltage. The device also provides a typical common-mode rejection ratio of 80 dB and an input bias current of 20 nA. Its 30 V operating capability suits 12 V automotive systems, industrial control equipment, audio electronics, and instrumentation while allowing operation from lower single-supply voltages. Each amplifier is frequency compensated and optimized for general-purpose analog design rather than high-speed differential signaling. A 1.2 MHz gain-bandwidth product is most useful at moderate closed-loop gains, while the 0.5 V/us slew rate limits large-signal response at low frequencies. The four independent channels can be configured independently for noninverting, inverting, comparator-like, summing, and feedback-amplifier circuits, subject to common-mode and output-swing limitations. Typical uses include automotive sensor interfaces, battery-powered monitoring equipment, active filters, audio preamplifiers, industrial transducers, and general-purpose control loops. Four amplifiers in one SOIC-14 package reduce board area and component count when several low-frequency analog channels are required. The automotive qualification makes the LM2902-Q1 family especially suitable for body electronics, actuator interfaces, and vehicle sensing systems. Design with the supply voltage, input common-mode range, output swing, input bias current, and capacitive-load drive in mind. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be kept away from switching nodes. Because the gain-bandwidth and slew-rate limits are modest, verify stability with the intended feedback network and load capacitance before scaling the design into production. This page combines manufacturer specifications, lifecycle information, application guidance, and same-footprint alternatives. It also provides practical design notes and parameter comparisons that help engineers distinguish functionally similar LM2902 variants and choose a suitable replacement without assuming that every ordering code is electrically identical.

Cotización Contacto
LM2902KAVQPWR - 30V Quad Op Amp with 2kV ESD | Texas Instruments
LM2902KAVQPWR

LM2902KAVQPWR - 30V Quad Op Amp with 2kV ESD | Texas Instruments

The Texas Instruments LM2902KAVQPWR is a quad, general-purpose operational amplifier built for single, dual, and split-supply operation. The device provides four amplifiers in a 14-pin TSSOP package, operates at 1.2 MHz gain-bandwidth, and offers 2 mV input offset voltage. The K suffix adds 2 kV human-body-model ESD protection, while the wide supply range supports industrial and automotive control systems operating from 3 V to 36 V. An operational amplifier, or op amp, is a high-gain differential-input amplifier that uses external feedback to set closed-loop gain. The LM2902KAV family belongs to the broader hierarchy of analog amplifiers, analog signal-processing ICs, and semiconductors. Four independent amplifiers in one package reduce component count and board area in designs that require multiple sensing, buffering, or gain stages. Key electrical characteristics include a 1.2 MHz gain-bandwidth product, 2 mV maximum input offset voltage for the BA version, 600 uV typical offset stated for the family, and 2 kV ESD protection on the K-suffix devices. The LM2902 supply arrangement supports 26 V single-supply operation or plus-and-minus 13 V dual-supply operation. Supply-current drain is specified as low as 0.8 mA typical and remains independent of supply voltage. The common-mode input voltage range includes ground, making the amplifier suitable for single-supply sensors whose outputs remain near 0 V. Differential input voltage capability and rail-to-rail output behavior also make the device useful in cost-sensitive analog signal chains where the output must approach supply limits. The B-generation device is positioned by Texas Instruments as a drop-in replacement for LM224, LM324, and LM2902 versions with improved specifications. Typical uses include industrial sensor conditioning, transducer amplification, low-frequency active filters, instrumentation amplifiers, audio preamplifier stages, motor-feedback networks, and general-purpose power-control loops. Four amplifiers can implement a complete low-speed control or measurement chain in a single package. PCB design should prioritize short feedback traces, clean grounding, and input-node protection from switching or high-energy sources. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be tied to a defined common-mode voltage rather than left floating. The 14-TSSOP package uses a narrow lead pitch, so inspect the manufacturer land pattern and solder reflow profile before assembly.

Cotización Contacto
LM2902KAVQPWRQ1 - 30V Quad AEC-Q100 Op Amp | TI
LM2902KAVQPWRQ1

LM2902KAVQPWRQ1 - 30V Quad AEC-Q100 Op Amp | TI

Texas Instruments LM2902KAVQPWRQ1 is a four-circuit bipolar operational amplifier designed for automotive applications, with a 3 V to 32 V supply range, 1.2 MHz gain-bandwidth product, 2 mV offset voltage, and a 14-pin TSSOP package. The device provides four independent amplifiers in one package, making it suitable for signal conditioning, sensing, buffering, and control circuits where component count and board area are important. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. The quad operational-amplifier category combines four amplifiers in one package, while the broader hierarchy includes voltage-feedback amplifiers, analog amplifiers, and integrated circuits. This makes the LM2902KAVQPWRQ1 useful wherever several low-to-moderate-bandwidth analog channels must operate from the same supply. Automotive qualification is a defining feature of the LM2902-Q1 family. According to the Texas Instruments LM2902-Q1 product information, the LM2902-Q1, LM2902B-Q1, and LM2902BA-Q1 devices are qualified in accordance with AEC-Q100 specifications. Other key characteristics include 2 kV improved ESD capability, a 0.5 V/µs slew rate, and an input common-mode voltage range that includes ground. The latter supports practical single-supply designs when the signal remains near the lower supply rail. The KAV version combines the standard bipolar amplifier architecture with 1.2 MHz gain-bandwidth performance and 2 mV offset voltage. Its four amplifier sections share the positive and negative supply pins, while each section retains its own input and output terminals. A gain-bandwidth product near 1.2 MHz supports general-purpose closed-loop operation well below the amplifier's upper frequency limit, depending on feedback topology and acceptable phase margin. Typical uses include automotive sensor interfaces, low-frequency active filters, transimpedance amplifiers, audio signal conditioning, battery monitoring, actuator drivers, and general analog control loops. The 14-pin TSSOP package reduces board footprint relative to four separate single or dual amplifier packages. Tape-and-reel packaging supports automated assembly, while the automotive qualification supports designs subject to rigorous reliability requirements. When designing around the LM2902KAVQPWRQ1, verify the complete input and output voltage limits under temperature and load conditions. Keep sensitive input traces away from switching nodes and provide local supply bypassing near the package. Account for output swing, slew-rate limits, input common-mode range, and stable feedback components when selecting gain and compensation values. This product page combines the manufacturer’s automotive qualification information with package, pinout, application, and replacement guidance. It also organizes drop-in alternatives by package and measured parameter differences, helping engineers compare upgrade paths before committing a PCB design.

Cotización Contacto
LM2902KD - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902KD

LM2902KD - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902KD is a quad general-purpose operational amplifier in a 14-pin SOIC package. Each of its four amplifiers supports a maximum supply voltage of 26 V, operates at a typical gain-bandwidth product of 1.2 MHz, and includes improved electrostatic-discharge protection rated to 2 kV. The device is designed for industrial and general-purpose analog signal-conditioning circuits that require four amplifiers in one package. An operational amplifier is a voltage-amplifying component whose open-loop gain is controlled by external feedback. In a closed-loop circuit, negative feedback establishes the actual gain and improves linearity, while the internal architecture provides high input impedance and low output impedance. The LM2902KD belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors, combining four amplifier channels in one package to reduce board area and simplify multi-channel designs. Key characteristics include four amplifier circuits, a 26 V maximum supply rating, a 1.2 MHz typical gain-bandwidth product, and 2 kV improved ESD protection. The listed input offset voltage is typically 3 mV, while typical input offset current is 2 nA. Typical supply-current drain is 0.8 mA per amplifier. These specifications make the device suitable for sensor interfaces, low-frequency signal conditioning, active filters, and industrial control applications where a robust, economical quad amplifier is preferred. The LM2902 family uses internal frequency compensation, allowing operation as a unity-gain amplifier without external compensation components. Its common-mode input voltage range includes ground, which supports direct sensing of low-side signals near the lower rail. This characteristic is useful in battery-powered, transducer, and grounded-source systems where the input signal can approach the supply floor. Typical applications include four-channel sensor conditioning, process-control instrumentation, current-loop receivers, audio preamplifier stages, active filters, and general buffer or gain stages. Because the device is specified for a 26 V maximum supply, it should not be treated as a 36 V part even though closely related LM2902B-family devices may support a wider supply range. Designers should verify common-mode range, output swing, input bias behavior, and channel-to-channel variation against the exact operating conditions. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer’s stability recommendations rather than left with floating inputs. This page organizes the LM2902KD electrical characteristics, package information, application guidance, verified source links, and documented drop-in alternatives for faster engineering selection. Use the manufacturer datasheet and pin-description table for final PCB routing, input/output assignment, and production-limit decisions.

Cotización Contacto
LM2902KDG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902KDG4

LM2902KDG4 - Quad 26V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902KDG4 is a general-purpose quad operational amplifier with four amplifier channels, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth performance, and improved 2 kV ESD protection. The device is supplied in a 14-pin SOIC package measuring 0.154 inch, or 3.90 mm, in body width. Each channel provides the standard differential-input, single-ended-output operational-amplifier arrangement. An operational amplifier is an analog integrated circuit that compares voltages applied to its inverting and non-inverting inputs and produces an output voltage representing that difference. When negative feedback surrounds the amplifier, it forms the core building block of voltage amplifiers, current buffers, comparators, filters, integrators, and sensor-conditioning circuits. The LM2902K places four such channels in one package, allowing a compact design to handle several independent low-frequency analog signals. The quad configuration provides four channels, 26 V maximum supply voltage, and 1.2 MHz gain-bandwidth product. These characteristics make the LM2902KDG4 suitable for general-purpose signal conditioning where the required signal bandwidth is below the amplifier's 1.2 MHz unity-gain capability. Its 2 kV improved ESD capability provides additional protection against electrostatic discharge encountered during handling or installation. The 14-SOIC construction is appropriate for conventional through-hole board assembly because the leads extend from the sides of the package. A quad package also reduces the number of amplifier packages required when a design needs four channels. Channel assignment and electrical behavior should be confirmed against the manufacturer pin-description table before PCB routing, particularly for power pins, input pins, and output pins. Typical uses include audio preamplification, instrumentation-signal conditioning, active filtering, transducer amplification, analog control loops, and general sensor interfaces. In a typical application, the LM2902KDG4 can amplify a low-level sensor signal, buffer an analog source, or implement an active filter with external resistors and capacitors. Common-mode range, input bias current, output swing, and stability requirements must be checked against the actual circuit. A key design consideration is power-supply bypassing. Place the required bypass capacitors close to the supply pins and route the ground return directly to the device ground. Avoid long analog traces, maintain a stable reference for each feedback network, and verify that the selected feedback and compensation values support the intended closed-loop bandwidth at the 1.2 MHz gain-bandwidth product. This product record combines the exact ordering information for LM2902KDG4 with package identification, lifecycle context, verified manufacturer characteristics, sourcing guidance, and engineering-oriented comparison information. It helps designers distinguish the discontinued orderable variant from related LM2902K products while focusing attention on the electrical and PCB implications of replacement.

Cotización Contacto
LM2902KNSRG4 - 26V Quad 1.2MHz Op Amp | Texas Instruments
LM2902KNSRG4

LM2902KNSRG4 - 26V Quad 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902KNSRG4 is a quadruple general-purpose operational amplifier designed for single-supply or split-supply operation, with four independent amplifiers, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and a 14-pin SOIC package. It combines low-noise performance with wide supply-voltage tolerance, making it suitable for industrial, automotive, and general analog signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. In its noninverting configuration it gains a signal applied to the positive input; in its inverting configuration it amplifies the input applied through the feedback network to the negative input. The LM2902K belongs to the hierarchy of operational amplifier, analog amplifier, linear amplifier, and semiconductor, while supporting applications from sensing and filtering to instrumentation and actuator control. Four independent amplifiers are integrated in one 14-pin SOIC, reducing board area compared with four single-amplifier packages. Each channel is frequency compensated and can operate from a single or split supply. According to the Texas Instruments product page, the device is a quad, 26 V, 1.2 MHz operational amplifier with improved 2 kV ESD protection. The four-channel organization is useful when a system requires several similar low-frequency amplification, buffering, or differential-input functions. The LM2902 architecture is intended for dependable, cost-conscious general-purpose analog designs rather than precision or high-speed signal chains. Its 1.2 MHz bandwidth supports moderate-frequency closed-loop operation, while the high-gain internal stages help implement common amplifier topologies. Split-supply operation is particularly useful in bipolar sensor circuits, where signals may be centered around 0 V and require both positive and negative output swing. Typical uses include industrial sensor interfaces, transducer conditioning, loop filtering, audio preamplification, automotive signal processing, and four-channel active filtering. The device can also implement comparators in applications where the response-speed requirements are modest and the input common-mode range is adequate. Each amplifier is independent, allowing unused channels to be configured according to the manufacturer's recommended stability practices. For PCB design, place the device to minimize noise-sensitive input routing and keep feedback traces short. Decoupling capacitors should be positioned close to the supply pins, while input and feedback paths should avoid nearby switching nodes and high-current return paths. Stable operation depends on choosing the correct feedback network and observing the input common-mode and output-swing limits for the selected supply voltage. This page organizes the device specifications, replacement options, application guidance, and practical design notes into a concise engineering reference. It also distinguishes true package-compatible alternatives from merely functional equivalents so replacement decisions can be checked against footprint, pinout, and operating requirements.

Cotización Contacto
LM2902KPWE4 - Quad 1.2MHz Op Amp, 26V, 14-TSSOP | Texas Instruments
LM2902KPWE4

LM2902KPWE4 - Quad 1.2MHz Op Amp, 26V, 14-TSSOP | Texas Instruments

The Texas Instruments LM2902KPWE4 is a quadruple general-purpose operational amplifier with a 1.2 MHz gain-bandwidth product, a 26 V maximum supply rating, and four independent amplifiers in a 14-pin TSSOP (PW) surface-mount package. An operational amplifier is a voltage-gain building block that amplifies the difference between two input voltages. A quad device packages four amplifiers sharing one supply pin and one ground pin, which cuts board area roughly in half compared with four single amplifiers and keeps sensitive analog channels on a common reference. Quad op amps sit in the hierarchy above single and dual amplifiers and below application-specific amplifiers, and they belong to the broader class of analog signal-conditioning integrated circuits used in nearly every industrial, automotive, and instrumentation design. Key features of the LM2902KPWE4 include a 1.2 MHz gain-bandwidth product that supports operation from DC to several hundred kHz of closed-loop bandwidth, a 26 V maximum total supply voltage for wide input swing, and improved ESD protection rated to 2 kV per the Texas Instruments LM2902K family description. The part is qualified to AEC-Q100 for automotive applications, and the E4 orderable suffix denotes the RoHS-compliant, lead-free finish. The 14-TSSOP body measures 0.173 inch (4.40 mm) wide, so the part fits the same footprint as other TI quad op amps such as the LM2902KPW. Architecturally the LM2902K family is a classic bipolar general-purpose amplifier stage with internal biasing, designed for single or dual supply operation and for driving typical resistive and capacitive loads within the output swing limits. Because it is a general-purpose part rather than a rail-to-rail precision amplifier, design work must confirm that the input common-mode range and output swing are adequate for the signal chain in question, and that the amplifier is stable with the output load capacitance present on the board. Typical uses include sensor signal conditioning, transducer and bridge-amplifier front ends, audio mixer sub-circuits, industrial loop-current receivers, and general instrumentation where four channels of gain are needed on a single board. Two channels can also be cross-coupled to build a higher-gain stage or an instrumentation-style front end. One key design consideration is that a 26 V supply capability does not mean the amplifier should be operated near 26 V: supply noise, output stage distortion, and device stress all rise as the rail voltage increases. Keep the supply within the intended range and decouple close to the supply pins with a 0.1 uF ceramic plus a bulk capacitor. This page brings together the manufacturer ordering information, drop-in replacement options in the same TSSOP-14 footprint, and applied design guidance for layout, decoupling, and stability that goes beyond the basic ordering table.

Cotización Contacto
LM2902KVQDRQ1 - 26V Quad Automotive Op Amp | Texas Instruments
LM2902KVQDRQ1

LM2902KVQDRQ1 - 26V Quad Automotive Op Amp | Texas Instruments

The Texas Instruments LM2902KVQDRQ1 is a four-channel, general-purpose operational amplifier designed for automotive applications in a 14-pin SOIC package. It supports supply voltages up to 26 V, operates from a single supply or split supplies, provides a gain-bandwidth product of 1.2 MHz, and has an input offset voltage of 2 mV. Each of its four amplifier channels is independent and internally frequency compensated, allowing multiple analog signal-conditioning stages to share one package. An operational amplifier is a high-gain, differential-input analog IC commonly used in sensor interfaces, buffer stages, error amplifiers, and low-frequency closed-loop control circuits. The LM2902-Q1 belongs to the operational-amplifier hierarchy, where quad operational amplifiers integrate four amplifiers into one IC while preserving independent signal paths. Its automotive qualification makes it suitable for electronic control units, body systems, instrumentation, and other 12 V vehicle platforms where operating-temperature robustness and supply-voltage tolerance are important. The device combines a 1.2 MHz gain-bandwidth product with a typical slew rate of 0.5 V/µs and a common-mode rejection ratio of 80 dB. Its 2 mV input offset specification supports accurate amplification of low-level signals, while the four-channel configuration reduces package count on analog-conditioning boards. The 26 V maximum supply rating provides additional input-voltage margin in automotive systems that operate from a 12 V battery through transient and filtering networks. Internally, each amplifier stage provides high open-loop gain and frequency compensation, allowing stable operation without an external compensation capacitor in ordinary closed-loop configurations. The amplifier can operate from a single positive supply or from split positive and negative supplies. Input bias current of approximately -0.5 µA and the stated CMRR characterize the input stage, helping engineers evaluate source-impedance matching and common-mode noise rejection before selecting external resistor networks. Typical uses include automotive sensor interfaces, battery monitoring, active filtering, actuator-signal conditioning, instrumentation amplifiers, and general-purpose analog control loops. The four channels can independently implement gain stages, buffers, comparators using suitable feedback arrangements, or voltage followers. Its SOIC-14 format supports conventional surface-mount assembly while providing enough pins for the four conventional dual-input amplifier channels and the two supply terminals. Design around the 26 V supply limit, maintain the required common-mode and output-voltage ranges, and account for input bias current when using high-source-impedance sensors. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Verify startup, shutdown, capacitive-load stability, and thermal performance in the final automotive environment rather than relying only on nominal amplifier parameters. This page combines the exact orderable MPN, automotive-family positioning, pin-level implementation guidance, drop-in comparison data, and application-focused design guidance to support faster component evaluation and PCB-level planning.

Cotización Contacto
LM2902KVQPWR - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM2902KVQPWR

LM2902KVQPWR - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902KVQPWR is a four-circuit general-purpose operational amplifier rated for up to 30 V, with a 1.2 MHz gain-bandwidth product, improved 2 kV ESD protection, and operation from -40°C to 125°C. The device is packaged in a 14-pin TSSOP (PW) package and is intended for industrial and general-purpose analog signal-conditioning designs. An operational amplifier, commonly called an op amp, is an analog semiconductor that uses high-gain differential amplification to compare two input voltages and drive an output according to their difference. The LM2902KV belongs to the operational amplifier hierarchy, which includes general-purpose amplifiers, voltage-feedback amplifiers, analog signal-conditioning ICs, and broader semiconductor components. Its four independent amplifiers can support multiple channels within one package. The principal features include a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 kV ESD protection. The four-amplifier configuration reduces board area in designs requiring several independent analog channels. According to the Texas Instruments LM2902KV product page, the KV version provides improved ESD capability while retaining the familiar LM2902-family architecture and extended operation from -40°C to 125°C. The LM2902 family is designed for general-purpose applications where economy, input-voltage range, and multiple channels are more important than precision or high-speed performance. Its relatively wide supply capability makes it suitable for circuits operating from industrial control voltages as well as lower-voltage systems. The 1.2 MHz gain-bandwidth product supports low-frequency signal conditioning, buffering, amplification, summation, filtering, and comparator-style threshold functions when operated with suitable feedback networks. Typical uses include industrial sensor interfaces, transducer signal conditioning, low-frequency active filters, analog summing amplifiers, instrumentation buffers, and general control-system analog channels. Because four amplifiers are integrated in one package, it can also reduce component count in multi-channel sensor, monitoring, and data-acquisition designs where channel-to-channel consistency and compact implementation are beneficial. Designers should account for input common-mode range, output swing, supply headroom, stability with the selected feedback network, input bias current, and the effects of capacitive loading. Decoupling capacitors should be placed close to the supply pins, and sensitive inputs should be routed away from high-current switching nodes. The TSSOP package requires careful assembly practices because its fine lead pitch can increase solder-bridging risk. This product page combines the manufacturer specifications, package details, application guidance, and qualified drop-in comparisons to simplify component selection. It also highlights the distinctions between the original LM2902 variants and the improved LM2902KV device, helping engineers confirm compatibility before changing an existing 14-pin TSSOP design.

Cotización Contacto
LM2902KVQPWRQ1 - 26V Quad 1.2MHz Automotive Op Amp | TI
LM2902KVQPWRQ1

LM2902KVQPWRQ1 - 26V Quad 1.2MHz Automotive Op Amp | TI

The Texas Instruments LM2902KVQPWRQ1 is a four-circuit general-purpose operational amplifier qualified for automotive applications, with a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and 2 mV offset voltage. It is housed in a 14-pin TSSOP package and is intended for applications requiring multiple independent high-voltage amplifier channels in one compact device. The LM2902-Q1 family is qualified according to AEC-Q100 specifications, while the LM2902B-Q1 and LM2902BA-Q1 members are described as next-generation versions with improved high-voltage operation. An operational amplifier, or op amp, is a voltage-controlled differential amplifier with very high open-loop gain. It compares two input voltages and drives its output toward the difference between them. Because the LM2902KVQPWRQ1 contains four independent, frequency-compensated amplifiers, one package can provide input buffering, sensor conditioning, voltage amplification, current sensing, and active filtering without requiring four separate devices. It supports single-supply operation and split-supply operation, subject to the device’s stated supply limits. The principal advantages of this device are its high-voltage capability, automotive qualification, integrated four-channel architecture, and broad applicability in industrial and vehicle electronics. The 1.2 MHz bandwidth supports general-purpose signal conditioning rather than high-speed precision analog work. Its 2 mV input offset voltage is useful for applications where the input signal is sufficiently large to keep offset errors below the required accuracy. The four channels also allow consistent amplifier performance across multiple signal paths in the same system. Typical applications include 12 V and 24 V automotive sensor interfaces, battery monitoring, pressure and temperature signal conditioning, current sensing, motor-control feedback networks, industrial control modules, and instrumentation buffers. The 14-pin TSSOP package is compact and suitable for high-density PCB layouts, but automotive designs should account for copper-area limitations, thermal dissipation, transient protection, and the need to keep sensitive input traces away from switching and power-conversion nodes. When selecting a replacement, verify the exact channel count, package, supply rating, offset voltage, bandwidth, common-mode behavior, output-drive capability, automotive qualification, and operating-temperature grade. The LM2902KVQPWRQ1 is best suited to four-channel, general-purpose automotive and industrial designs where 26 V operation and AEC-Q100 qualification are more important than high precision or high speed. This page combines the manufacturer product information with practical comparison, replacement, and design guidance for engineers evaluating the device in an existing circuit.

Cotización Contacto
LM2902M - Quad 26 V 1.2 MHz Operational Amplifier | onsemi
LM2902M

LM2902M - Quad 26 V 1.2 MHz Operational Amplifier | onsemi

onsemi LM2902M is a quad operational amplifier containing four independent, internally compensated high-gain amplifiers in a 14-pin SOIC package. The verified product data identifies it as a standard general-purpose amplifier with a 26 V maximum supply, 1.2 MHz gain-bandwidth product, and typical input offset voltage of 2 mV. It is designed for cost-sensitive analog signal-conditioning circuits that require more than one amplifier in a compact surface-mount package. An operational amplifier is an amplifier IC that uses high open-loop gain and negative feedback to control gain accurately. A quad device integrates four amplifiers, reducing package count and simplifying layouts requiring several channels. The LM2902 family belongs to the operational-amplifier hierarchy and supports common analog functions such as signal amplification, buffering, active filtering, comparisons, transducers, and low-frequency closed-loop control. The key headline characteristics are four amplifier circuits, a 26 V supply rating, 1.2 MHz gain-bandwidth product, 2 mV typical offset voltage, and a 14-pin SOIC package. Internal frequency compensation makes each channel suitable for many unity-gain or moderate-gain applications without an external compensation network. On-chip capacitors in each amplifier support stable operation as a general-purpose voltage-feedback amplifier. The architecture follows the classic high-voltage, internally compensated operational-amplifier approach. Four independent amplifiers share one monolithic substrate but do not share internal signal paths. This allows the same device to implement four separate channels, such as a dual-sensor front end or two complete analog-processing chains. The verified data does not provide exact input bias current, output-current capability, slew rate, or common-mode limits, so those specifications require confirmation from the selected manufacturer's datasheet. Typical uses include industrial sensor interfaces, low-frequency active filters, audio preamplifier stages, process-control modules, instrumentation, and general buffer or gain stages. The quad organization is particularly useful when four similar analog functions must fit on a PCB. Actual circuit suitability depends on supply voltage, source impedance, load impedance, signal frequency, output swing, stability, and thermal conditions. For PCB design, place the device so sensitive analog inputs remain short and route outputs away from switching nodes and high-current paths. Bypass each supply connection near the package with suitable decoupling, maintain a common ground reference, and verify unused-channel inputs are biased so they do not float. The SOIC package also requires a thermal strategy when nearby circuitry drives substantial channel dissipation. This page consolidates the verified distributor and manufacturer product information, identifies where identical MPNs come from different manufacturers, and separates confirmed LM2902M characteristics from parameters that still require manufacturer-specific datasheet review before design release.

Cotización Contacto
LM2902M96 - Quad 1MHz Operational Amplifier | Harris Corporation
LM2902M96

LM2902M96 - Quad 1MHz Operational Amplifier | Harris Corporation

The Harris Corporation LM2902M96 is a quad operational amplifier in a 14-pin SOIC package. The device contains four independent amplifiers, is associated with a 1 MHz gain-bandwidth characteristic, and is identified for commercial, industrial, and military applications. Its quad architecture lets one package support several analog signal-processing functions while simplifying board layout and inventory management. An operational amplifier is a voltage-amplified, high-gain analog building block used in sensing, buffering, amplification, filtering, and control circuits. The LM2902 belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, comparator-adjacent interface functions, and general-purpose signal-conditioning ICs. Its four integrated channels make it useful where multiple independent analog paths are required within the same subsystem. The principal features of the LM2902M96 are its four-amplifier configuration, 1 MHz bandwidth indication, and 14-pin SOIC implementation. These characteristics make the device suitable for transducers, sensor conditioning, analog signal buffers, feedback networks, and general instrumentation. The single package also reduces the number of discrete components required when four amplifier channels are needed at the same time. The M96 ordering code identifies the surface-mount 14-pin SOIC configuration. This package supports conventional PCB assembly and provides a practical option for industrial control and instrumentation designs requiring multiple analog channels. Because electrical ratings differ across the wider LM2902 family, designers should confirm supply voltage, input common-mode range, output swing, input bias current, output current, and temperature range against the applicable manufacturer datasheet before finalizing a design. Typical uses include low-frequency process-control loops, sensor amplifiers, analog monitoring channels, buffered instrumentation inputs, and small-signal conditioning stages. The quad organization is especially helpful in equipment that must process several transducers or supply and return signals, such as data-acquisition modules, industrial controllers, test equipment, and communication or power-management interface boards. A key design practice is to verify the complete operating envelope rather than relying only on the 1 MHz bandwidth designation. Input signals must remain within the amplifier's valid common-mode range, output loading must remain within its drive capability, and power-supply bypassing should be placed close to the supply pins. Decoupling values, stability requirements, and output-load restrictions should follow the datasheet and the intended feedback configuration. This page organizes the LM2902M96's core technical identity, verified drop-in candidates, package considerations, commercial information, and application guidance. It also provides practical design notes intended to help engineers move from general amplifier selection to a board-level implementation while preserving the correct 14-pin footprint and checking device-specific electrical limits.

Cotización Contacto
LM2902MTX/NOPB - Quad 26V 1MHz Op Amp | Texas Instruments
LM2902MTX/NOPB

LM2902MTX/NOPB - Quad 26V 1MHz Op Amp | Texas Instruments

Texas Instruments LM2902MTX/NOPB is a low-power, general-purpose quad operational amplifier containing four independent, internally frequency-compensated amplifiers. It operates from a single power supply, supports supply voltages up to 26 V, and operates at gain-bandwidth frequencies up to 1 MHz. The device is packaged in a 14-pin TSSOP (PW) package and supplied in tape-and-reel packaging for automated surface-mount assembly. An operational amplifier is an analog signal-conditioning semiconductor that compares two input voltages and amplifies their difference. The LM2902 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog signal-processing IC, and semiconductor. Its four independent channels make it suitable for circuits requiring several similar amplifier stages in one compact package, while internal frequency compensation simplifies closed-loop design without external frequency-compensation components. The LM2902MTX/NOPB combines four general-purpose amplifier channels with a 26 V maximum supply rating and gain-bandwidth performance of approximately 1 MHz. Each channel has its own inputs and output, allowing simultaneous use in independent signal paths. The low-power design is intended for general-purpose analog systems where a modest bandwidth is sufficient. Tape-and-reel packaging supports volume manufacturing and automated placement in compact industrial, instrumentation, and control equipment. Internal frequency compensation establishes the dominant-pole behavior of each amplifier and permits stable operation in common non-inverting and inverting configurations without additional compensation networks. The manufacturer describes the LM2902-N family as four independent, high-gain, internally frequency-compensated operational amplifiers designed for operation from a single power supply over a wide voltage range. This architecture favors straightforward implementation over the flexibility offered by externally compensated amplifiers. Typical uses include low-frequency sensor conditioning, transducer amplification, analog summing and comparison stages, active filtering, instrumentation buffers, and industrial control interfaces. Four integrated channels can reduce the component count in designs that require multiple amplifier functions. When one channel is used for a critical precision path, the other channels must still meet the same supply and stability constraints, making common-layout and simultaneous-signal behavior important design considerations. A key design consideration is power-supply range. Although the device supports supplies up to 26 V, input and output voltage limits must be respected during startup, shutdown, and transient conditions. Decoupling capacitors should be placed close to the supply pins, while input sources should avoid excessive capacitance unless its effect on stability is evaluated. The 14-pin TSSOP footprint also requires attention to thermal dissipation and copper routing during assembly. This page combines the exact orderable MPN, package and channel information with practical application guidance, engineering design notes, and a same-footprint comparison. It is intended to help engineers identify the correct quad amplifier, assess replacement options, and plan a robust single-supply analog circuit without relying on assumptions about package or pin compatibility.

Cotización Contacto
LM2902MX - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902MX

LM2902MX - Quad 26V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2902MX is a four-channel, internally frequency-compensated operational amplifier designed for single-supply operation with a 26 V maximum supply voltage. Each amplifier has a typical gain-bandwidth product of 1.2 MHz and an input offset voltage of 2 mV, while all four amplifiers are housed in a 14-pin SOIC package. The quad configuration provides four independent signal-conditioning channels in one compact surface-mount device. An operational amplifier is an analog signal-conditioning IC that compares voltages applied to its inverting and non-inverting inputs and drives its output to amplify the difference between them. The LM2902 belongs to the operational-amplifier hierarchy within analog ICs and semiconductor devices. Its internal frequency compensation makes it suitable for closed-loop gain stages without an external compensation network, simplifying industrial, instrumentation, and control-system designs. Key characteristics include four amplifier channels, a 1.2 MHz typical gain-bandwidth product, a 2 mV typical input offset voltage, and a typical open-loop DC gain of 100 dB. These characteristics support general-purpose applications involving signal buffering, current-to-voltage conversion, differential amplification, filtering, and low-frequency closed-loop control. A broad common-mode input range and single-supply capability make the device practical for circuits powered from industrial and automotive-style rails. The LM2902MX uses a bipolar amplifier architecture. Internal frequency compensation stabilizes operation at unity gain and simplifies PCB implementation, but the device is intended primarily for lower-frequency analog signals rather than high-speed signal chains. Its 1.2 MHz gain-bandwidth product should be considered when selecting closed-loop gain because bandwidth decreases as gain increases, which can affect signal rise time, phase margin, and loop stability. Typical uses include transducer-signal conditioning, industrial sensor interfaces, current-loop receivers, audio preamplification, analog-control feedback networks, and four-channel instrumentation systems. Multiple independent amplifier sections can process related signals without requiring four separate packages, reducing board area and simplifying power distribution. The quad organization is particularly useful when a design repeats the same amplifier topology across several measurement or control channels. Design the power rails and input common-mode range so they remain within the amplifier's operating limits throughout startup, load transients, and fault conditions. Place input and output bypassing capacitors close to their associated pins, keep feedback paths compact, and avoid long parallel traces that can increase noise pickup. Confirm stability at the intended closed-loop gain and temperature before releasing the PCB layout. This page combines the device's principal electrical characteristics with application guidance, package details, drop-in replacement analysis, and an engineering comparison table. It is intended to help designers determine whether the LM2902MX's four-channel architecture, electrical limits, and 14-pin SOIC footprint fit a new analog design.

Cotización Contacto
LM2902MX/NOPB - 26V 1.2MHz Quad Op Amp | Texas Instruments
LM2902MX/NOPB

LM2902MX/NOPB - 26V 1.2MHz Quad Op Amp | Texas Instruments

Texas Instruments LM2902MX/NOPB is a low-power, internally frequency-compensated, quad operational amplifier designed for single-supply operation across a wide voltage range. The device provides four amplifier channels in a 14-pin SOIC package, with a 1.2 MHz gain-bandwidth product, 2 mV typical input offset voltage, and approximately 0.5 V/us slew rate. Its high-voltage operating capability makes it useful in industrial control, instrumentation, sensor conditioning, audio, and power-supply feedback circuits. The LM2902MX/NOPB is identified as a standard general-purpose amplifier, while the LM2902 family is also described as a quad, 26 V operational amplifier with 1.2 MHz bandwidth. An operational amplifier is an analog signal-conditioning integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The LM2902 contains four independent amplifier sections with internal frequency compensation, allowing stable operation in common noninverting, inverting, summing, comparator, and feedback configurations. Its low-power design is intended for battery-powered and general-purpose systems where a wide supply-voltage range is more valuable than high-speed performance. Key features include a 3 V to 32 V single-supply operating range, a 26 V maximum total supply voltage, 1.2 MHz gain-bandwidth product, 2 mV typical input offset voltage, and approximately 0.5 V/us slew rate. The four-channel architecture reduces component count and board area when multiple analog signals require conditioning. The 14-pin SOIC package is also available in related LM2902 order variants, making footprint planning important when selecting an exact replacement. The LM2902 family uses a bipolar voltage-feedback architecture. Internal compensation removes the need for an external frequency-compensation capacitor in typical closed-loop configurations. The device can operate from a single positive supply or from split positive and negative supplies. Its relatively modest bandwidth makes it appropriate for slower control and measurement loops rather than high-speed video, RF, or precision signal-chain applications. Typical uses include transducer and sensor conditioning, low-frequency active filters, current-loop and voltage-feedback control, audio preamplification, battery-powered instrumentation, and general analog signal processing. The wide supply range also permits operation from industrial 24 V systems when the total supply voltage remains within the device rating. Designers should account for input common-mode range, output swing, input bias current, and stable feedback-network selection when using the amplifier near its voltage limits. A key design consideration is the relationship between supply voltage, input range, and output swing. A nominal 3 V minimum supply does not mean the input and output can reach every rail voltage, so the signal amplitudes must remain inside the amplifier's specified common-mode and output ranges. Decoupling capacitors should be placed close to the supply pins, and feedback resistors should be selected to keep closed-loop gain and noise performance appropriate for the application. This product page combines the manufacturer's LM2902 product information, distributor references, package identification, and practical guidance for signal conditioning, supply bypassing, common-mode limits, and replacement planning.

Cotización Contacto
LM2902N - Quad 26V 1MHz Op Amp | Texas Instruments
LM2902N

LM2902N - Quad 26V 1MHz Op Amp | Texas Instruments

The Texas Instruments LM2902N is a quad, general-purpose operational amplifier in a 14-pin DIP package, with four independent amplifiers per device. The verified source data identifies it as a 26 V maximum supply part with 1 MHz gain-bandwidth behavior, making it suitable for low-cost signal conditioning, instrumentation, and control circuits. The LM2902N combines independent high-gain stages with internally compensated operation from a single supply, while the DIP package supports through-hole assembly and conventional prototype or repair workflows. An operational amplifier is an analog integrated circuit that uses differential input and feedback to control an output voltage. In the broader electronics hierarchy, an op amp belongs to the amplifier-IC family, performs closed-loop signal amplification, and commonly supports filtering, buffering, level shifting, sensing, and control applications. A quad package provides four amplifiers in one IC, reducing component count while preserving separate signal paths where independent channels are useful. The verified product information specifically describes the LM2902-N as a quad 26 V, 1 MHz operational amplifier. The LM2902 family is associated with wide single-supply operation, internally frequency-compensated amplifiers, and general-purpose analog designs. These characteristics are useful when a board needs four amplifier channels with moderate bandwidth rather than a high-speed precision device. Because the available data does not provide the complete electrical tables, detailed input-bias-current, output-swing, noise, and common-mode specifications must be verified in the manufacturer datasheet before production release. Typical uses include sensor conditioning, low-frequency active filters, industrial control loops, audio preamplifier stages, and general-purpose analog signal paths. The 14-pin DIP outline is appropriate when the design uses a through-hole footprint or a manually assembled educational or industrial prototype. Designers should confirm the exact pinout, supply limits, common-mode range, output drive, and stability requirements for the intended operating point rather than relying only on the family-level description. A key design consideration is decoupling: place the supply bypass capacitor close to the device power pins and provide a stable, low-impedance return path. Input and feedback components should be arranged to minimize parasitic pickup and unwanted oscillation. This page distinguishes verified LM2902-N facts from unspecified parameters, making it a practical starting point for procurement and engineering review. The LM2902N combines four channels, a 26 V supply class, and a 1 MHz operating-speed class in a through-hole 14-pin DIP. This combination supports cost-sensitive analog designs where external compensation, rail-to-rail operation, or high bandwidth is not required.

Cotización Contacto
LM2902N/PB - Quad 26V 1MHz Op Amp | Texas Instruments (Lead-Free (Pb-Free))
LM2902N/PB

LM2902N/PB - Quad 26V 1MHz Op Amp | Texas Instruments (Lead-Free (Pb-Free))

The Texas Instruments LM2902N/PB is a quad, general-purpose operational amplifier in a 14-pin DIP package, with four independent amplifiers per device. The verified source data identifies it as a 26 V maximum supply part with 1 MHz gain-bandwidth behavior, making it suitable for low-cost signal conditioning, instrumentation, and control circuits. The LM2902N/PB combines independent high-gain stages with internally compensated operation from a single supply, while the DIP package supports through-hole assembly and conventional prototype or repair workflows. An operational amplifier is an analog integrated circuit that uses differential input and feedback to control an output voltage. In the broader electronics hierarchy, an op amp belongs to the amplifier-IC family, performs closed-loop signal amplification, and commonly supports filtering, buffering, level shifting, sensing, and control applications. A quad package provides four amplifiers in one IC, reducing component count while preserving separate signal paths where independent channels are useful. The verified product information specifically describes the LM2902-N as a quad 26 V, 1 MHz operational amplifier. The LM2902 family is associated with wide single-supply operation, internally frequency-compensated amplifiers, and general-purpose analog designs. These characteristics are useful when a board needs four amplifier channels with moderate bandwidth rather than a high-speed precision device. Because the available data does not provide the complete electrical tables, detailed input-bias-current, output-swing, noise, and common-mode specifications must be verified in the manufacturer datasheet before production release. Typical uses include sensor conditioning, low-frequency active filters, industrial control loops, audio preamplifier stages, and general-purpose analog signal paths. The 14-pin DIP outline is appropriate when the design uses a through-hole footprint or a manually assembled educational or industrial prototype. Designers should confirm the exact pinout, supply limits, common-mode range, output drive, and stability requirements for the intended operating point rather than relying only on the family-level description. A key design consideration is decoupling: place the supply bypass capacitor close to the device power pins and provide a stable, low-impedance return path. Input and feedback components should be arranged to minimize parasitic pickup and unwanted oscillation. This page distinguishes verified LM2902-N facts from unspecified parameters, making it a practical starting point for procurement and engineering review. The LM2902N/PB combines four channels, a 26 V supply class, and a 1 MHz operating-speed class in a through-hole 14-pin DIP. This combination supports cost-sensitive analog designs where external compensation, rail-to-rail operation, or high bandwidth is not required.

Cotización Contacto
LM2902NG - 4-Channel 1MHz Op Amp in 14-PDIP | onsemi
LM2902NG

LM2902NG - 4-Channel 1MHz Op Amp in 14-PDIP | onsemi

onsemi LM2902NG is a four-channel, general-purpose operational amplifier in a 14-pin PDIP package. The device provides true differential inputs, a 1 MHz gain-bandwidth product, approximately 40 mA output current, 50 dB minimum common-mode rejection, and a typical input offset voltage of 7 mV. Its four amplifiers are designed for instrumentation, buffering, signal conditioning, and general analog signal-processing systems operating from a single supply. An operational amplifier, or op amp, is a high-gain differential-input amplifier that uses negative feedback to control gain and improve linearity. In the product hierarchy, the LM2902NG belongs to the general-purpose operational-amplifier class, within analog amplifier ICs and integrated circuits. Unlike rail-to-rail precision amplifiers, this device is intended primarily for conventional supply rails where adequate input and output common-mode ranges are available. The four integrated channels make the LM2902NG useful where several independent low-frequency analog functions are required. Its 1 MHz bandwidth supports general-purpose gain and signal conditioning above DC, while true differential inputs suit instrumentation and feedback networks. The 7 mV typical input offset and 50 dB minimum CMRR should be considered when precision requirements are moderate rather than stringent. Each amplifier includes the internal characteristics expected of a practical general-purpose quad op amp, including differential input support, output drive capability, and operation from a single power supply. The 14-pin PDIP format facilitates inspection, prototyping, and through-hole assembly. Designers requiring a surface-mount implementation should select a compatible alternative package rather than attempting to mount the PDIP directly. Typical applications include sensor-signal conditioning, low-level signal buffering, active filtering, transducer-interface circuits, test equipment, industrial control systems, and educational instrumentation. The four-channel organization can reduce component count and simplify board allocation when an analog subsystem needs two or more gain stages. Design with the supply voltage, common-mode input range, output swing, and output-current limits defined by the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and input, feedback, and output routing should avoid long traces susceptible to noise pickup. This product page combines manufacturer and distributor technical details, package guidance, application analysis, replacement criteria, and PCB-oriented design notes. It is intended to help engineers identify whether the LM2902NG's four-channel architecture and 14-PDIP footprint fit a single-supply analog design before committing to a BOM.

Cotización Contacto
LM2902NS - Quad 26V 1.2MHz Op Amp | Texas Instruments
LM2902NS

LM2902NS - Quad 26V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM2902NS is a general-purpose quad operational amplifier integrating four independent amplifier circuits in a 14-pin SOIC package. The device is designed for a 26 V maximum supply rating, a 1.2 MHz gain-bandwidth product, and an input offset voltage of 2 mV. Its four-amplifier configuration allows one device to implement multiple signal-conditioning, comparison, filtering, or control functions while conserving board area. An operational amplifier is a high-gain, internally compensated differential-input amplifier used to amplify voltage differences, buffer signals, compare thresholds, and drive feedback networks. The LM2902NS belongs to the operational-amplifier hierarchy, where it is also classified as a general-purpose amplifier, analog amplifier, and linear integrated circuit. Its integrated quad arrangement makes it suitable when four similar amplifier channels are required rather than four separate single or dual packages. The four internal circuits provide the principal functional advantage of the LM2902NS. A single package can support four independent signal paths, reducing component count and simplifying PCB layout when the same amplifier type is used throughout a subsystem. The 26 V supply rating provides headroom for industrial and automotive-style control environments, while the 1.2 MHz bandwidth supports applications from DC precision amplification to moderate-frequency signal processing. Texas Instruments identifies the LM2902NS as a standard general-purpose amplifier with four circuits in a 14-SO package. Its 2 mV maximum input offset voltage is relevant when the application compares small sensor voltages against references or develops low-level control signals. Because the four amplifiers are independent, their input and output pins can support separate analog channels rather than requiring a common signal path. Typical uses include four-channel sensor conditioning, precision threshold comparison, current-loop signal conditioning, industrial process-control interfaces, buffered instrumentation, and general embedded analog signal processing. In each case, the integrated quad topology reduces the number of amplifiers needed while retaining independent channel routing and common package-level supply handling. PCB design should preserve analog signal integrity by keeping input and output routing short, decoupling the supply pins close to the device, and avoiding current injection beneath the package. Confirm input common-mode range, output swing, supply limits, stability requirements, and channel-specific bandwidth needs against the manufacturer datasheet before finalizing the circuit. This page combines the Texas Instruments product description, exact-order MPN information, package details, verified source listings, and practical selection guidance. It also distinguishes same-package replacement candidates from broader functional alternatives so engineers can assess footprint compatibility, bandwidth, offset voltage, and supply capability before changing an approved BOM.

Cotización Contacto