Circuitos integrados

PIC12F675T-I/MD

PIC12F675T-I/MD - 8-Bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip Technology PIC12F675T-I/MD is an 8-bit Flash-based CMOS microcontroller in the PIC12F family, packaged in an 8-lead DFN (4x4 mm, exposed pad) with tape and reel packaging. It integrates a 20 MHz core, 1.75 KB (1K x 14 words) of Flash program memory, 64 bytes of RAM, 128 bytes of EEPROM, a 10-bit ADC with 4 channels, and an on-chip 4 MHz internal oscillator. The device operates from 2.0V to 5.5V and features 6 general-purpose I/O pins. What is a Flash-based 8-bit microcontroller? An 8-bit microcontroller is a small computer-on-a-chip that processes data in 8-bit chunks and integrates CPU, memory (Flash for program storage, RAM for data, EEPROM for non-volatile data), peripherals (ADC, timers, communication), and I/O on a single die. Flash memory allows in-circuit reprogramming via ICSP, making these MCUs ideal for prototyping, low-volume production, and field-upgradable designs. PIC microcontrollers are widely used in cost-sensitive embedded applications due to their deterministic RISC architecture, low power consumption, and a 35-instruction set that simplifies firmware development. The PIC12F675 delivers 200 ns instruction execution, hardware UART, comparators, and an enhanced PWM module. Its nanopower technology provides low sleep current for battery-operated designs. The integrated 10-bit ADC with 4 channels eliminates external analog components in many sensing applications. Six GPIO pins support direct interfacing to sensors, switches, LEDs, and communication lines. The device also features a programmable brown-out reset (BOR), watchdog timer, and in-circuit serial programming (ICSP) for in-field firmware updates. The architecture is built on Microchip's enhanced mid-range 8-bit RISC core with a single accumulator and hardware multiplier support. The Harvard architecture separates program (Flash) and data (RAM) buses, allowing simultaneous instruction fetch and data access. The 14-bit wide instruction word reduces code density issues common with 12-bit PIC parts. The 10-bit ADC uses successive approximation with internal or external voltage reference selection. Typical applications include low-power sensor nodes, battery management, LED lighting controllers, automotive interior electronics, consumer appliance control, and small IoT edge devices. The wide operating voltage range supports direct connection to 2xAA/3xAA battery packs as well as regulated 3.3V and 5V rails. Designers benefit from Microchip's MPLAB X IDE and XC8 compiler ecosystem, which provide free development tools. When designing with the PIC12F675, ensure ICSP programming header access is preserved on the PCB. The internal 4 MHz oscillator eliminates the external crystal in many designs, but precision timing applications should still use an external resonator or crystal. Decoupling capacitors (100 nF plus bulk) must be placed close to VDD. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet, helping engineers select, source, and apply the PIC12F675T-I/MD with confidence.

Cotización Contacto

PIC12F675T-I/MF

PIC12F675T-I/MF - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip

The Microchip Technology PIC12F675T-I/MF is an 8-bit CMOS Flash-based microcontroller in a PIC® 12F family architecture, delivering 20MHz (200 ns instruction execution) performance with 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and 128 bytes of EEPROM. Housed in an 8-pin DFN-S (6x5 mm) surface-mount package, the device integrates 6 I/O pins, a 4-channel 10-bit ADC, one comparator, and a hardware USART/SCI module, all operating from a 2.0V to 5.5V supply. The part is specified for the industrial temperature range of -40°C to +85°C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data RAM, and configurable peripherals. The 8-bit MCU class, including the PIC12F family, is widely used in cost- and space-constrained applications that need deterministic real-time response rather than high computational throughput. PIC12F microcontrollers sit at the entry level of Microchip's 8-bit portfolio, prioritizing low pin count, low power, and ease of development with only 35 single-word instructions. Key features of the PIC12F675T-I/MF include 1.75KB self-programmable Flash, 128 bytes of EEPROM for non-volatile data storage, an internal 4MHz oscillator with software-selectable calibration, and a 10-bit ADC with 4 input channels that can also be used as digital I/O. The integrated comparator supports simple analog signal conditioning, while the USART/SCI module enables asynchronous serial communication with baud rates up to several hundred kbps. The device also provides an in-circuit serial programming (ICSP) interface that allows field firmware updates via two standard pins. Architecturally, the PIC12F675 uses a Harvard RISC core with a 14-bit instruction word, 8-bit data path, and a single accumulator (W register) that delivers predictable, deterministic instruction timing. The Flash memory uses a 14-bit word organization that maps to 1024 instruction words (1.75KB). The internal 4MHz oscillator and four available clock modes allow designers to balance active current consumption against execution speed, and the device supports both internal and external oscillator configurations for EMI-sensitive designs. Typical applications include battery-powered sensor nodes, consumer appliance control, LED driver controllers, simple state machines, and automotive accessory modules where AEC-Q100 grade variants (e.g., PIC12F675-I/MF in automotive screening) are acceptable. The small 8-pin DFN package is well suited for space-limited PCB designs such as remote keyless entry fobs, smart thermostats, and personal medical accessories. Designers should note that the DFN-8 (6x5 mm) exposed pad must be soldered to a sufficient copper area for thermal dissipation and electrical grounding. Decoupling capacitors of 100nF and 10µF should be placed within 3 mm of the VDD pin to ensure stable operation across the 2.0V to 5.5V supply range. For noise-sensitive ADC readings, AVSS should be tied directly to the ground plane, and the analog inputs should be guarded by digital traces. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Cotización Contacto

PIC12F675T-I/SN

PIC12F675T-I/SN - 8-Bit 20MHz CMOS Flash MCU, 1.75KB | Microchip

The Microchip Technology PIC12F675T-I/SN is an 8-bit RISC CMOS Flash-based microcontroller delivering 20 MHz (200 ns instruction cycle) performance from a 1.75 KB (1K x 14) Flash program memory and 64 bytes of RAM in an 8-pin SOIC package. It integrates a 4-channel 10-bit Analog-to-Digital Converter, one capture/compare/PWM module, and an internal 4 MHz oscillator with software-selectable calibration, enabling compact designs that minimize external component count. An 8-bit microcontroller is a microprocessor core that processes data 8 bits at a time and is optimized for embedded control tasks such as sensing, timing, and GPIO expansion. Within the broader semiconductor taxonomy, this PIC12F675 belongs to the 8-bit microcontroller family -> microcontroller unit (MCU) -> embedded processor -> integrated circuit. The PIC12F675 sits in Microchip's PIC12F mid-range architecture, the smallest-footprint sub-family of the PIC® mid-range line, designed for low-pin-count applications where PCB area, BOM count, and cost dominate the design trade-off. Key features include a 35-instruction RISC instruction set (single-cycle except branches), an 8-level deep hardware stack, interrupt capability, 6 digital I/O pins (5 GPIO + 1 input-only), an internal comparator with on-chip reference, and Flash program memory with self-programmability for in-field firmware upgrades. The 'T' suffix indicates Tape & Reel packaging and the 'I' suffix denotes the industrial temperature range of -40 °C to +85 °C. The device operates from 2.0 V to 5.5 V, supporting both 3.3 V and 5 V system rails. Technically, the PIC12F675 uses a Harvard architecture with separate program and data buses, allowing instruction fetch and operand read to occur in the same cycle. Its enhanced FLASH memory uses 14-bit-wide instructions, the wider word size enabling 35 opcodes that cover arithmetic, bit-manipulation, and peripheral control. The 10-bit ADC achieves a typical acquisition time suitable for slow-changing sensor signals such as thermistors, photocells, and battery monitors. Typical applications include low-power sensor nodes, automotive body electronics, industrial control loops, AC power measurement, smoke detectors, and any place a small analog/mixed-signal MCU is required. Pairing the internal ADC with the on-chip comparator makes it especially well-suited to battery chargers and threshold-detection circuits. When designing with this part, ensure decoupling capacitors are placed within 5 mm of VDD, route the MCLR pin through a 10 kΩ pull-up for reliable reset, and budget Flash endurance at 100K erase/write cycles per the manufacturer datasheet. This page synthesizes distributor pricing, drop-in alternatives within the PIC12F family, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC12F683-E/MD

PIC12F683-E/MD - 8-Bit 20MHz MCU 3.5KB Flash 8-DFN | Microchip

The Microchip Technology PIC12F683-E/MD is an 8-bit PIC12 family CMOS flash microcontroller delivering 20 MHz instruction throughput (200 ns instruction cycle) with 3.5 KB (2K x 14) of Flash program memory, 128 bytes SRAM, and 256 bytes of EEPROM, housed in a compact 8-pin DFN (4x4 mm) package. It integrates a 4-channel 10-bit ADC, two 8-bit timers plus one 16-bit timer, a 4-channel hardware PWM module, an enhanced USART, and an internal 8 MHz precision oscillator selectable via software across 31 kHz to 8 MHz. An 8-bit microcontroller (MCU) is a single-chip computer that integrates an 8-bit CPU core, program memory (Flash/ROM), data memory (SRAM), non-volatile EEPROM, and a fixed set of peripherals onto one die. PIC12F microcontrollers sit within Microchip's mid-range 14-bit instruction architecture hierarchy, which itself belongs to the broader PIC family of RISC microcontrollers (PIC -> PIC10/12/16/18 -> PIC12F low-pin-count subfamily). The PIC12F683 specifically targets space-constrained designs that still require analog sensing and PWM control, blending digital I/O with a precision 10-bit ADC on a minimal 8-pin footprint. Key features of the PIC12F683-E/MD include an operating voltage range of 2.0 V to 5.5 V, industrial extended temperature range of -40 °C to +125 °C, low-power nanoWatt technology with typical sleep current under 1 µA, and a configurable 8 MHz internal oscillator that eliminates the need for an external crystal in most designs. Its 4-channel 10-bit ADC supports both standard and high-speed conversions, while the enhanced capture/compare/PWM (ECCP) module drives MOSFETs, LEDs, or motor phases directly from the GPIO pins. The architecture uses a 14-bit wide instruction word, 8-level hardware stack, and 35 single-word instructions, simplifying firmware development. The /MD suffix indicates a 4x4 mm DFN surface-mount package, the most compact option in the PIC12F683 family, while the -E prefix indicates the extended -40 °C to +125 °C industrial temperature range. Code protection, a 1k erase/program cycle endurance rating on Flash, and 100k cycle endurance on EEPROM make it suitable for field-deployed embedded nodes. Typical applications include battery chargers, LED lighting controllers, fan speed regulators, small sensor signal conditioners, and low-cost consumer appliance controls. Its tiny DFN-8 footprint and integrated peripherals make it ideal for designs where PCB area is at a premium. When designing with this device, reserve adequate copper area for the exposed pad thermal dissipation and follow Microchip's recommended decoupling network (100 nF plus 10 µF bulk) within 5 mm of the VDD pin. This page combines distributor stock and pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC12F683-E/P

PIC12F683-E/P - 8-bit 20MHz 3.5KB Flash MCU | Microchip

The Microchip PIC12F683-E/P is an 8-bit Flash-based CMOS microcontroller built on Microchip's mid-range 14-bit instruction set architecture, offered in an 8-pin PDIP through-hole package. The device integrates 3.5 KB (2K x 14) of Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM data memory, with a maximum CPU clock of 20 MHz derived from the internal oscillator or an external crystal. It operates across an extended industrial temperature range (-40C to +125C), as indicated by the -E (extended) suffix, with a supply voltage range of 2.0 V to 5.5 V. An 8-bit microcontroller (MCU) is a small single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), volatile working memory (RAM), non-volatile data memory (EEPROM), and a set of programmable I/O pins on a single silicon die. 8-bit MCUs sit at the entry level of the embedded computing hierarchy (8-bit -> 16-bit -> 32-bit MCU -> microprocessor -> SoC) and remain dominant where cost, simplicity, and deterministic real-time response matter more than raw throughput. The PIC12F683 is the highest-spec member of Microchip's 8-pin PIC12F family and adds peripherals absent on smaller cousins such as the PIC12F508/509. Key features include a 4-channel 10-bit Analog-to-Digital Converter (ADC), one Enhanced Capture/Compare/PWM (ECCP) module, one Capture/Compare/PWM (CCP) module, four 8-bit timers plus one 16-bit timer, an internal 8 MHz precision oscillator, a comparator module, and nanoWatt power-management modes for low-power battery applications. Six general-purpose I/O pins are available, all capable of interrupt-on-change wake-up. The -E temperature grade and PDIP-8 form factor make this part particularly well suited to prototyping, hobby projects, and through-hole industrial designs that must survive harsh thermal environments. The PIC12F683 architecture is built on a 14-bit-wide instruction word with single-cycle execution on most instructions (except branches), giving 200 ns instruction time at 20 MHz. Internal peripherals are mapped into a unified data-memory SRAM area and configured through Special Function Registers (SFRs). The nanoWatt technology provides multiple idle and sleep modes that can reduce quiescent current to the sub-microamp range, enabling years of operation from a coin cell. Typical applications include LED lighting control, battery chargers, sensor signal conditioning, low-power remote controls, smoke detectors, and small appliance motor control. The integrated ADC and PWM peripherals allow direct interface to analog sensors and MOSFET/IGBT gate drivers without external analog circuitry, reducing bill-of-materials cost and PCB area. When designing with the PIC12F683, ensure that MCLR is pulled high through a 10 kohm resistor and that the ICSP programming header is accessible for field updates. Designers migrating from older PIC12F parts should review the ECCP initialization sequence, which differs from the CCP modules on legacy devices. This page synthesizes verified distributor pricing, drop-in 8-pin PDIP alternatives from the PIC12F family, and practical design notes not consolidated on the manufacturer datasheet.

Cotización Contacto

PIC12F683-I/MD

PIC12F683-I/MD - 8-bit 20MHz MCU 3.5KB Flash 6 I/O | Microchip

The Microchip Technology PIC12F683-I/MD is an 8-bit PIC microcontroller featuring a mid-range x14 RISC architecture, 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and 256 bytes of EEPROM data memory. The part operates up to 20 MHz instruction clock and integrates a 4-channel 10-bit ADC, a precision internal oscillator, and a nanoWatt power-saving mode set, packaged in an 8-pin DFN (4x4 mm) with an exposed pad. Background: An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for embedded control tasks such as sensor reading, simple actuation, glue logic, and protocol conversion. Microchip's PIC12 family targets ultra-low-pin-count applications (8 pins) where PCB real estate is constrained. Within the broader taxonomy, the PIC12F683 belongs to: microcontroller -> 8-bit MCU -> mid-range PIC architecture -> flash-based programmable MCU -> embedded computing IC. Key features include a wide operating voltage range of 2.0V to 5.5V, six general-purpose I/O pins with interrupt-on-change capability, an internal 8 MHz oscillator (calibrated to ±1% across Vdd and temperature), one Enhanced Capture/Compare/PWM (ECCP) module, one comparator, and nanoWatt sleep modes that drop quiescent current to the microamp range for battery-powered designs. Technically, the PIC12F683 executes one instruction per clock cycle (200 ns at 20 MHz) using the 14-bit instruction word, giving deterministic timing for control loops. The device is supported by the MPLAB X IDE and the XC8 C compiler, enabling C-based firmware development alongside assembly. The integrated 10-bit ADC samples up to four analog channels, while the ECCP and PWM peripherals support motor, LED, and signal-conditioning topologies without external circuitry. Typical applications include battery-powered sensor nodes, IR remote controls, simple LED drivers, capacitive-touch interface replacements, and auxiliary housekeeping logic on larger boards. The 8-pin DFN footprint (~9 mm² of board area) is significantly smaller than SOIC-18 alternatives, enabling miniaturized products such as wearables, IoT edge nodes, and disposable medical indicators. When designing with this part, allocate the exposed pad (EP) as a thermal and ground bond; route ground and decoupling to it on the top layer. Verify Vdd decoupling with a 0.1 µF ceramic placed within 5 mm of the supply pin, and ensure in-system serial programming (ICSP) pads are accessible for production flashing. This page synthesizes distributor pricing, drop-in PIC12 family alternatives, and practical layout notes for compact PCB designs - content not found in the manufacturer datasheet alone.

Cotización Contacto

PIC12F683-I/P

PIC12F683-I/P - 8-Bit 20MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12F683-I/P is an 8-bit Flash-based CMOS microcontroller in the PIC12 mid-range family, delivering 20MHz CPU performance with 3.5KB (2K x 14) of Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM data memory, all housed in a through-hole 8-pin PDIP package. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, memory, and peripherals into a single IC. The PIC12F683 belongs to Microchip's mid-range x14 architecture family, positioned in the broader hierarchy of microcontroller -> embedded controller -> semiconductor device. It is widely used as a compact glue-logic replacement, sensor-interface controller, and low-power autonomous subsystem in cost-sensitive designs. Key features include a 4-channel 10-bit ADC with internal voltage reference, one 8-bit and one 16-bit timer, enhanced PWM/capture/compare module, a comparator with programmable on-chip reference, and nanoWatt Technology power management for ultra-low sleep currents below 1 µA typical. The device supports In-Circuit Serial Programming (ICSP) via two pins, allowing firmware updates after PCB assembly. The PIC12F683-I/P operates from 2.0V to 5.5V and offers six general-purpose I/O pins with individual direction control and weak pull-ups. Its mid-range instruction set provides 35 single-word instructions, all single-cycle except branches. This combination of integrated peripherals, small footprint, and proven toolchain support (MPLAB X IDE, XC8 compiler) makes the part popular for hobbyist and industrial applications. Typical applications include LED drivers, sensor signal conditioning, battery chargers, simple motor control, and consumer appliance user-interface modules. Its internal 8MHz oscillator and on-chip peripherals minimize external component count, enabling two-layer through-hole designs. When designing with the PIC12F683-I/P, plan for ICSP header access even on prototypes - the ICSP pins (GP0/GP1) are multiplexed with the serial interface. Decouple VDD with a 100nF ceramic capacitor placed within 5mm of the package, and reserve an area for an optional 32.768kHz crystal on GP4/GP5 if low-power RTCC operation is needed. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC12F683-I/SN

PIC12F683-I/SN - 8-bit 20MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC12F683-I/SN is an 8-bit Flash-based CMOS microcontroller in an 8-pin SOIC package, featuring a 20 MHz maximum CPU clock, 3.5 KB (2K x 14) of Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM data memory. Built on Microchip's mid-range 14-bit instruction set architecture, it integrates a 4-channel 10-bit ADC, one 8-bit and one 16-bit timer, a capture/compare/PWM (CCP) module, and an enhanced USART. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory, RAM, and configurable peripherals. The PIC12F683 belongs to the low-pin-count (8-pin) Flash MCU family, a sub-category of 8-bit microcontrollers targeted at cost- and size-sensitive embedded designs where only a handful of I/O lines are needed but on-chip analog and timing peripherals are still required. Key features of this device include a wide 2.0 V to 5.5 V operating voltage range, ultra-low-power nanoWatt technology with standby current of approximately 50 nA, and operating currents of roughly 11 µA at 32 kHz and 220 µA at 4 MHz. It also provides six independently configurable bidirectional I/O pins, an internal 8 MHz oscillator with software calibration, and an integrated analog comparator. The 'I' suffix designates the industrial temperature grade of -40 °C to +85 °C, while '/SN' denotes the 8-pin SOIC package. Typical applications for the PIC12F683-I/SN include battery-powered sensor nodes, LED lighting controllers, simple motor and fan control loops, consumer remote controls, and small home appliances. The combination of nanoWatt sleep modes and on-chip peripherals makes it well suited for designs that must run for years on a single coin-cell battery. When designing with this part, choose the appropriate internal or external oscillator configuration early in the firmware planning stage and budget Flash and RAM carefully against the 2K x 14 program word limit and 128-byte data SRAM. Decoupling the VDD pin with a 0.1 µF ceramic capacitor placed within a few millimeters of the device is strongly recommended. This page synthesizes distributor pricing, drop-in SOIC-8 alternatives from the same PIC12F family, and practical design notes not found in the manufacturer datasheet, helping engineers select and source the right PIC12F variant for cost-sensitive, low-pin-count embedded designs.

Cotización Contacto

PIC12F683T-E/MF

PIC12F683T-E/MF - 8-Bit 20MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC12F683T-E/MF is an 8-bit PIC® RISC flash microcontroller running up to 20 MHz instruction rate, packaged in an 8-pin DFN-S EP (6x5 mm) with exposed thermal pad and shipped on tape-and-reel. The PIC12F683T-E/MF integrates 3.5 KB (2K x 14) of self-programmable flash program memory, 256 bytes of EEPROM data memory, and 128 bytes of SRAM on a mid-range 14-bit instruction core that executes most instructions in 200 ns. Four 10-bit ADC channels, one enhanced capture/compare/PWM (ECCP) module, and an internal 8 MHz / 31 kHz oscillator cluster make it a complete SoC in 8 pins. A microcontroller (MCU) is a single-chip computer that combines a CPU, program and data memory, peripherals, and I/O on one die. The PIC12F683 belongs to the mid-range PIC12 family, part of the broader 8-bit PIC microcontroller architecture that evolved from the original Harvard-design PIC1650. Within Microchip's portfolio, the PIC12 sub-family targets low-pin-count, cost-sensitive embedded designs that still need on-chip EEPROM, ADC, and PWM. The 'F' denotes flash program memory, which allows in-circuit re-programming for field upgrades and development iteration. Key features of the PIC12F683 include 5 or 6 general-purpose I/O pins (depending on oscillator selection), four 10-bit ADC channels with internal 1.024V / 2.048V / 4.096V voltage references selectable via the FVRCON register, a 16-bit ECCP module for motor/PWM control, hardware USART, an SR-latch, comparator module with absolute voltage reference, and the nanoWatt power-managed modes that drop standby current to ~50 nA typical. Watchdog timer with on-chip RC oscillator, brown-out reset, and low-voltage programming are all standard. Operating from 2.0 V to 5.5 V across -40 °C to +125 °C (E = extended temperature), the PIC12F683 is built on a CMOS process optimized for low static current and wide supply tolerance. The enhanced mid-range core extends the instruction set to 35 single-word instructions while preserving pin and code compatibility with legacy PIC12 and PIC16 devices, which eases migration. The DFN-S package (also called 8-VDFN exposed-pad) measures 6 x 5 mm and provides a low thermal-resistance path to PCB copper, supporting the industrial temperature range without an explicit heatsink. Typical applications include low-pin-count consumer and industrial sensor conditioning, LED lighting drivers, battery chargers, motor control loops for small DC fans and pumps, remote-keyless entry (RKE) transmitters, and home-automation nodes. The 4x10-bit ADC and 16-bit PWM together suit closed-loop tasks such as PID-controlled solenoid drive or constant-current LED dimming. Internal oscillator options (INTOSC 31 kHz to 8 MHz with PLL) eliminate external crystals, reducing BOM cost in price-sensitive designs. A key design consideration is the DFN exposed-pad layout: the central EP must be soldered to a thermal pad tied to ground to meet the datasheet thermal envelope. Engineers should also verify that the oscillator selection bit configuration leaves at least four usable I/O pins; with the 8 MHz INTOSC selected, GP5 becomes an oscillator pin and only five GPIOs remain. Programming is supported by Microchip's MPLAB X IDE and the XC8 compiler at no charge. This page consolidates drop-in DFN alternatives, distributor pricing as of 2026-09-15, and design notes beyond the Microchip datasheet summary to help engineers shorten the PIC12F683T-E/MF selection cycle.

Cotización Contacto

PIC12F752-E/MF

PIC12F752-E/MF - 8-bit MCU 1.75KB Flash 6 I/O 20MHz | Microchip

The Microchip Technology PIC12F752-E/MF is an 8-bit PIC microcontroller built on the mid-range core, delivering 5 MIPS at 20 MHz operation and integrating 1.75 KB (1K x 14) of self-read/write Flash program memory with 64 bytes of SRAM and a 20 MHz internal oscillator in an 8-pin DFN-EP (3x3) package. The PIC12F752 family is engineered for cost-sensitive analog-intensive applications, pairing a RISC instruction set with two high-speed analog comparators (20 ns response), one Capture-Compare-PWM (CCP) module, a 9-bit DAC and four 10-bit ADC channels in a footprint that fits where 6-pin or 8-pin discretes previously ruled. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory (Flash), and peripheral interfaces on one die, optimized for deterministic real-time control rather than throughput. PIC12F devices sit at the small-pinned end of Microchip's PIC mid-range architecture, hierarchically classified as: PIC microcontroller -> PIC12 family -> PIC12F sub-family -> 8-pin OTP/Flash parts. This taxonomy matters because the PIC12F752 shares tools, instruction set, and pinout conventions with the broader PIC12F series while specializing in analog signal conditioning. Key features of the PIC12F752-E/MF include six general-purpose I/O pins (re-mappable via peripheral pin select on compatible siblings), one 8-bit and one 16-bit timer, two analog comparators with programmable reference, an enhanced PWM with auto-shutdown, and an internal 8 MHz oscillator that can be tuned across 32 kHz to 20 MHz via the OSCTUNE register. The device operates from 2.0 V to 5.5 V and includes in-circuit serial programming (ICSP) plus a 64-byte EEPROM emulation region in Flash. The architecture uses a Harvard 14-bit instruction word with a 13-bit program counter and an 8-level hardware stack, yielding deterministic interrupt latency and single-cycle instruction execution except for branches. The integrated analog peripherals allow direct interfacing to sensors without external op-amps, which is the principal reason designers select PIC12F752 over general-purpose 8-bit alternatives. NanoWatt power management offers idle, sleep and watchdog-based wake modes with currents measured in microamps. Typical applications include SMPS auxiliary control, LED lighting drivers, battery chargers, sensor signal conditioning, and small motor or fan controllers. The DFN-EP package exposes a thermal pad that doubles as an additional ground and provides low theta-JA for the modest power dissipation of this device, making it suitable for hand-held and sealed enclosures. When designing with this part, reserve pin 4 (GP3/MCLR) for either reset or digital input only - it is not a true bidirectional I/O on this family. Ensure the exposed pad is soldered to a ground plane for thermal and electrical performance. This page synthesizes distributor pricing, verified parametric data, and practical design notes not found in the manufacturer datasheet alone, supporting engineers evaluating the PIC12F752-E/MF for new designs or as a drop-in upgrade path.

Cotización Contacto

PIC12F752-E/P

PIC12F752-E/P - 8-Bit 5MIPS Flash MCU | Microchip Technology

The Microchip Technology PIC12F752-E/P is an 8-bit PICmicro flash microcontroller with 1.75 KB of program memory, 64 bytes of RAM, six general-purpose I/O pins, an 8 MHz internal oscillator, and 5 MIPS processing performance, supplied in an 8-pin PDIP package. The PIC12F752-E/P uses the E temperature grade and is listed in production by Microchip, although the manufacturer identifies PIC16F1703 as a newer device. A PICmicro microcontroller is a compact RISC-based embedded controller combining flash program memory, data RAM, general-purpose I/O, oscillators, and optional analog or timing peripherals on one integrated circuit. This device belongs to the PIC12 family hierarchy, where the 12 designation identifies a small-footprint controller intended for embedded logic, sensing, and control tasks requiring modest program space and low component count. The verified device data identifies 1.75 KB, organized as 1K by 14 words, of flash program memory and 64 bytes of RAM. Its six I/O pins provide enough external connectivity for basic digital control, status indicators, switches, and simple peripheral interfaces. An 8 MHz internal oscillator supports operation without an external crystal, while the listed 5 MIPS performance rate provides ample throughput for compact control loops and sequential logic. The PIC12F752/HV752 architecture uses a 13-bit program counter capable of addressing an 8K by 14 program-memory space, although only the first 1K by 14 words are physically implemented in the PIC12F752. This architecture reduces unnecessary program-memory capacity when a design does not need a larger code space. The related HV752 family is distinguished by the inclusion of higher-voltage operating capability, so it should not be assumed to be a performance-identical substitute without reviewing the manufacturer data sheet. Typical uses include compact appliance controls, small sensor interfaces, LED status systems, simple timers, and dedicated embedded automation where an internal oscillator and a small PDIP footprint simplify prototyping and through-hole assembly. The six available I/O pins make the device most appropriate when the external interface is modest and the firmware does not require extensive communications resources. Designers should preserve adequate decoupling near the supply pins, route oscillator-sensitive signals away from switching nodes, and verify every peripheral assignment against the package-specific pin table. The temperature-grade code E and the /P package suffix must be checked against environmental and assembly requirements. Software should also be validated for clock tolerance, brownout behavior, and programming configuration before production release. This page consolidates manufacturer status information, verified distributor specifications, pricing context, compatible-package candidates, and engineering-oriented selection guidance. Its practical value is the comparison of memory organization, I/O availability, package compatibility, temperature-grade choices, and design constraints that engineers must verify before treating an alternative as a drop-in replacement.

Cotización Contacto

PIC12F752-E/SN

PIC12F752-E/SN - 8-bit MCU, 1.75KB Flash, 6 I/O, 20MHz | Microchip

The Microchip Technology PIC12F752-E/SN is an 8-bit PIC® mid-range microcontroller built on a RISC architecture, delivering up to 20 MHz (5 MIPS) of CPU performance in a compact 8-pin SOIC (SN) package. The device integrates 1.75 KB (1K x 14) of self-read/write Flash program memory, 64 bytes of RAM, and 128 bytes of EEPROM, with 6 general-purpose I/O pins supporting peripheral pin select flexibility for digital and analog functions. An 8-bit microcontroller is a single-chip computer that combines a CPU, RAM, non-volatile program memory, and peripherals on one die. Within the broader taxonomy, the PIC12F752 belongs to the 8-bit MCU class -> microcontrollers -> embedded processors -> integrated circuits -> semiconductors. The 8-bit class remains popular for cost- and power-sensitive applications where raw computational throughput is less critical than deterministic I/O handling, simple BOM, and a well-supported development ecosystem. Key features include two high-speed analog comparators with 20 ns propagation delay, one Capture/Compare/PWM (CCP) module, a 10-bit ADC with 4 channels and 100K samples-per-second conversion, two 8-bit timers and one 16-bit timer, an internal 8 MHz oscillator, and an on-chip voltage reference. The -E suffix denotes the extended industrial temperature grade of -40°C to +125°C, making the device suitable for harsh-environment applications. The PIC12F752's enhanced mid-range core executes 35 single-word instructions and supports hardware interrupt context saving, easing firmware architecture for motor control and power conversion. Internal oscillator calibration supports ±1% accuracy across voltage and temperature, eliminating the need for an external crystal in most designs. The 8-pin SOIC footprint simplifies hand-prototyping and rework while supporting reflow profiles compatible with lead-free surface-mount assembly per JEDEC J-STD-020. Typical applications include LED lighting controllers, BLDC motor commutation, fan control, battery chargers, sensor signal conditioning, and low-cost consumer appliances where the 6-I/O constraint fits the use case. The internal voltage reference and high-speed comparators enable primary-side regulation in flyback converters and direct comparator-based feedback loops. When designing with this part, reserve at least one I/O for in-circuit serial programming (ICSP) and use the recommended MPLAB X IDE configuration bits to select the internal oscillator and disable unused peripherals. For analog designs, allocate adequate PCB ground pour around the AVSS/AVDD pair and decouple both with 100 nF ceramic capacitors placed within 5 mm of the supply pins. This page synthesizes verified distributor pricing, package-correct drop-in alternatives, and application-specific design guidance that supplements the Microchip datasheet and PIC12F752 product page.

Cotización Contacto

PIC12F752-I/MF

PIC12F752-I/MF - 8-Bit MCU 20MHz 1.75KB Flash 8-DFN | Microchip

The Microchip Technology PIC12F752-I/MF is an 8-bit PIC microcontroller in the PIC12F family, featuring a mid-range core running at up to 20 MHz instruction rate with 1.75 KB (1K x 14) of self-read/write Flash program memory, packaged in an 8-pin DFN (3x3 mm) with exposed thermal pad. It integrates 2 high-speed analog comparators with 20 ns propagation delay, 1 Capture/Compare/PWM (CCP) module, and an internal 8 MHz oscillator that eliminates the need for an external crystal in many designs. The device targets low-pin-count cost-sensitive applications requiring on-chip analog and digital peripherals without external components. A PIC12F-series microcontroller is a member of Microchip's 8-bit mid-range architecture family, which provides a balance of low cost, low power, and adequate processing throughput for simple embedded control tasks. PIC microcontrollers use a Harvard architecture with separate program and data buses, and the 12F sub-family specifically targets applications requiring only 6-8 I/O pins. The PIC12F752 extends the 12F line by adding two fast analog comparators and a CCP module, making it suitable for power-conversion and signal-conditioning tasks where discrete analog components would otherwise be required. Key features of the PIC12F752 include 64 bytes of SRAM, 128 bytes of EEPROM, 5 channels of 10-bit ADC, a 5-bit DAC, an enhanced PWM with dead-band control, and a 4-bit comparator with programmable reference. The device operates from 2.0 V to 5.5 V across the industrial -40C to +85C range and supports In-Circuit Serial Programming (ICSP) via two pins. The internal oscillator can be tuned to 8 MHz with ±1% accuracy after calibration, allowing designs to operate without external timing components. The PIC12F752 architecture uses a 14-bit instruction word with single-cycle execution (except branches), giving roughly 5 MIPS throughput at 20 MHz. Peripherals are mapped to a banked register file accessible through dedicated SFRs, and the core supports hardware context save/restore for interrupt-driven firmware. The analog comparators can directly trigger the CCP for hardware-based control loops such as peak-current-mode power supplies or zero-crossing detectors. Typical applications include LED lighting drivers, battery chargers, switch-mode power supply control, small motor control, sensor signal conditioning, and consumer appliance user-interface controllers. The CCP and high-speed comparator combination is particularly well suited to peak-current-mode converters and synchronous rectifier timing. When designing with the PIC12F752, note that the device has only 6 general-purpose I/O pins. Designers must plan pin allocation carefully when using ICSP (which consumes two pins) and the analog peripherals simultaneously. The internal oscillator accuracy is sufficient for UART-free applications but external timing is recommended for serial communication. A decoupling capacitor of 100 nF placed within 5 mm of the VDD pin is recommended per Microchip's analog design guidelines.

Cotización Contacto

PIC12F752-I/P

PIC12F752-I/P - 8-bit MCU, 1.75KB Flash, 8-PDIP | Microchip

The Microchip Technology PIC12F752-I/P is an 8-bit PIC microcontroller featuring 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and a 20 MHz maximum CPU speed, housed in an 8-pin PDIP (through-hole) package with industrial temperature grade (-40C to +85C). It is part of the PIC12F mid-range core family, integrating 5 general-purpose digital I/O pins, 2 high-speed analog comparators (20 ns response), 1 Capture-Compare-PWM (CCP) module, and an internal 8 MHz oscillator that delivers 5 MIPS instruction throughput. An 8-bit PIC microcontroller is a compact, Harvard-architecture RISC processor that executes one instruction per cycle (excluding branches), combining CPU core, non-volatile Flash program memory, data RAM, and configurable peripherals in a single IC. In the broader taxonomy, the PIC12F752 belongs to: microcontroller -> 8-bit MCU -> PIC microcontroller -> PIC12F mid-range family -> semiconductor. Microcontrollers are the foundation of embedded intelligence in everything from appliance controls to automotive subsystems. Key differentiating features include the 8 MHz internal oscillator (factory calibrated, eliminating external crystal cost), 2 analog comparators with 20 ns propagation delay (rare in this pin-count class), and a single 10-bit PWM/CCP channel with up to 10-bit resolution for motor or LED control. The device operates across 2.0V to 5.5V VDD, supports in-circuit serial programming (ICSP) via two pins, and includes a power-on reset / brown-out reset (BOR) block. Architecturally the PIC12F752 uses the enhanced mid-range 14-bit instruction set with 8-level hardware stack and 25 instruction opcode count. It integrates a 4-channel 10-bit ADC (with the 6-pin variant supporting up to 6 analog inputs) and a configurable 8-bit timer (Timer0/Timer1/Timer2) set, providing a balanced analog/digital peripheral mix for low-pin-count embedded designs. Typical applications include battery chargers, LED lighting drivers, small motor control (fans, pumps), appliance primary control boards, smoke detectors, and IoT sensor node MCU roles. In each case, the part's 8-pin footprint and internal oscillator reduce BOM cost while the comparators enable fast analog threshold detection. When designing with this part, verify that the 5 GPIO pins are sufficient for your application including any required UART/SPI/I2C interfaces (which are bit-banged on this device). Add a 0.1uF decoupling capacitor directly across VDD/VSS pins, kept within 5 mm trace length. For designs above 16 MHz CPU clock, the internal oscillator accuracy may require software trim or an external crystal on RA4/RA5. This page synthesizes distributor pricing, drop-in alternatives from the same PIC12F family, and practical design notes not found in the standalone manufacturer datasheet.

Cotización Contacto

PIC12F752-I/SN

PIC12F752-I/SN - 20MHz 8-Bit Flash MCU | Microchip Technology

The Microchip Technology PIC12F752-I/SN is an 8-bit PIC mid-range flash microcontroller rated for operation up to 20 MHz, with 1.75 KB of flash program memory organized as 1K x 14 words and 64 bytes of data RAM. The device is packaged in an 8-pin SOIC and provides six I/O lines, two high-speed analog comparators, and one Capture/Compare/PWM module. Its internal 8 MHz oscillator supports a 5 MIPS instruction rate when operating with the appropriate clock configuration. A PIC mid-range 8-bit microcontroller is a compact embedded-control device that combines a processor core, flash memory, RAM, oscillators, and dedicated peripherals on one integrated circuit. The PIC architecture belongs to the broader 8-bit microcontroller and embedded-controller hierarchy, making it useful for products requiring inexpensive deterministic control, flexible serial programming, and mixed analog and digital signal acquisition. PIC12F752 is positioned for compact control, sensing, and low-pin-count automation products. The PIC12F752-I/SN combines 1.75 KB of self-programmable flash with 64 bytes of data RAM. Two analog comparators provide 20 ns response performance, while the Capture/Compare/PWM peripheral supports timing and basic waveform-generation functions. Six I/O pins make the device useful for small control loops, sensor interfaces, and compact embedded products. The internal 8 MHz oscillator eliminates the need for an external clock in designs that do not require a different clock frequency. The mid-range PIC core executes a 35-instruction set and supports a 200 ns instruction cycle at the 20 MHz maximum operating frequency. The MCU also includes an internal oscillator, self-read/write flash capability, and the low-pin-count protections described in the PIC12F752/HV752 family datasheet. These characteristics make the device practical for applications in which program memory is sufficient for compact control firmware rather than intensive computation. Typical uses include simple motor or actuator control, temperature and industrial sensor interfaces, LED status and signage controllers, compact power-system monitoring, and small consumer products. The two comparators are especially useful for direct threshold detection, while the CCP module can reduce external timing-component requirements. The six available I/O lines should be considered carefully when designing a system that needs multiple digital signals and analog inputs. For PCB implementation, use the manufacturer's SOIC pinout and pin-description table, provide the required programming and decoupling connections, and maintain a clear signal path between the six I/O pins. The -I suffix denotes the industrial-temperature grade, while /SN identifies the SOIC package. Before production release, validate startup, oscillator behavior, programming configuration, peripheral pin assignments, and analog switching at the lowest intended supply voltage. This product page combines the manufacturer datasheet, distributor specifications, lifecycle information, and practical design guidance for evaluating the PIC12F752-I/SN in compact embedded-control designs. It also distinguishes confirmed drop-in alternatives from variants that use different package dimensions or pin arrangements, helping engineers make a PCB-compatible sourcing decision.

Cotización Contacto

PIC12F752T-I/SN

PIC12F752T-I/SN - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip

The Microchip Technology PIC12F752T-I/SN is an 8-bit PIC microcontroller based on the enhanced mid-range core, delivering up to 20MHz instruction execution from a 1.75KB (1K x 14) Flash program memory and 64 bytes of RAM, housed in an 8-pin SOIC (SN) package. It integrates a precision 20MHz internal oscillator, two high-speed analog comparators with 20ns response time, one Capture-Compare-PWM (CCP) module, and a 10-bit Analog-to-Digital Converter (ADC), positioning it as a feature-dense MCU for compact analog-intensive embedded designs. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of 8/16/32-bit Harvard-architecture microcontrollers from Microchip Technology. The PIC12F752 belongs to the mid-range core family, which sits between the baseline 12-bit core and the enhanced 16-bit core. PIC microcontrollers fall under the broader category of microcontrollers (MCUs) -> embedded controllers -> semiconductors -> integrated circuits. The 8-pin PIC12F series is purpose-built for low pin-count analog and timing applications where PCB real estate is at a premium. Key features of the PIC12F752T-I/SN include 5 I/O pins (6 total I/O including MCLR/RA3), internal 8MHz oscillator with PLL support for 20MHz operation, two 20ns analog comparators ideal for power supply feedback loops and zero-crossing detection, one CCP module supporting PWM up to 10-bit resolution, 4 channels of 10-bit ADC, and an extended operating voltage range of 2.0V to 5.5V. The I in the part number designates the industrial temperature grade of -40C to +85C, and the /SN suffix identifies the 8-pin SOIC package on tape and reel (T = Tape & Reel). The PIC12F752 architecture uses a RISC instruction set with only 35 instructions to learn, simplifying firmware development. It features self-read/write Flash capability enabling in-application programming (IAP), a 4 hardware timer module stack (Timer0, Timer1, Timer2, WDT), and patented low pin-count analog IP. The integrated 8MHz internal oscillator eliminates the need for external crystal components, reducing BOM cost and PCB area. Typical applications include LED lighting drivers, DC-DC converter secondary-side control, battery chargers, motor control for small DC fans and pumps, power supply monitoring, and consumer appliance control. The two high-speed comparators make it well-suited for switch-mode power supply (SMPS) peak current-mode control loops. When designing with this MCU, allocate at least 10uF of bulk decoupling near the VDD pin and place a 100nF ceramic bypass capacitor as close to the IC as possible. The internal oscillator is factory-calibrated to within +/-1% typical accuracy, eliminating external timing components for most cost-sensitive designs. This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC12F mid-range family, and practical design notes not found in the manufacturer datasheet alone, providing engineers a single source for sourcing and replacement decisions.

Cotización Contacto

PIC12HV609-E/MS

PIC12HV609-E/MS - 8-bit Flash MCU, 1.75KB, 8MSOP | Microchip

The Microchip Technology PIC12HV609-E/MS is an 8-pin, 8-bit flash-based CMOS microcontroller from the PIC12 family, featuring 1.75 KB of Flash program memory (1K x 14), 64 bytes of RAM, and 6 I/O pins housed in an 8-MSOP (MS) package. It integrates an internal 8 MHz oscillator and supports instruction execution up to 20 MHz when driven from an external source, while the high-voltage (HV) variant accepts an unregulated supply up to the maximum VDD rating without requiring a local regulator on the input rail. What is a PIC12 microcontroller? The PIC12 family is Microchip's baseline 8-bit mid-range microcontroller line, using a RISC-style Harvard architecture with a small instruction set (typically 35 instructions), single-cycle execution at the system clock, and integrated peripherals such as comparators, timers, and a watchdog. Within the broader hierarchy, PIC12 sits below PIC16/PIC18, and PIC microcontrollers belong to the 8-bit microcontroller category of embedded semiconductors. Key features of the PIC12HV609-E/MS include 1.75 KB Flash (1K x 14 words), 64 bytes RAM, an 8 MHz internal oscillator, one 8-bit timer (TMR0), one 16-bit timer (TMR1), an enhanced mid-range core with 35 instructions and 8 hardware stack levels, 25 mA source/sink I/O drive, and a user-configurable analog comparator with hysteresis. The HV prefix means the device includes a built-in shunt regulator, allowing direct operation from 2.0 V to user-defined maximum (typical application: unregulated battery or rectified supply) without external regulation. The -E suffix denotes the -40C to +125C extended industrial temperature grade. Architecturally, the PIC12HV609 uses the same enhanced mid-range core as the standard PIC12F609, but with an internal shunt regulator front-end instead of a direct VDD pin. This internal regulator drops the high input voltage down to the core's regulated logic rail, simplifying designs that would otherwise require external zener or LDO regulators. Program memory is Flash and self-programmable under software control, supporting in-circuit serial programming (ICSP). Typical applications include battery-powered products where an unregulated stack must feed the MCU directly (HV variant specific), consumer appliances, simple sensor conditioning nodes, automotive body electronics within the -40C to +125C range, low-cost motor control loops, and any general-purpose 8-bit replacement for legacy PIC10/PIC12 designs requiring a small pin-count footprint. The device also fits remote controls, lighting controllers, and standby controllers in white goods. When designing with this part, leave adequate ground copper under the exposed MSOP pad for thermal relief, place the 0.1 uF VDD decoupling capacitor within 2-3 mm of the VDD pin, and ensure ICSP connections (PGD/PGC) are accessible for production programming. The internal shunt regulator dissipates significant power at high input voltages, so derate VDD_MAX by application voltage to stay within the thermal envelope.

Cotización Contacto

PIC12HV609-E/P

PIC12HV609-E/P - 8-bit Flash MCU, 1.75KB, 8-Pin PDIP | Microchip

The Microchip PIC12HV609-E/P is an 8-bit Flash-based CMOS microcontroller in an 8-pin PDIP package, built on Microchip's mid-range PIC core with 35 instructions and 8 hardware stack levels. It integrates 1.75 KB of Flash program memory, 64 bytes of RAM, and a high-voltage shunt regulator (4 mA to 50 mA range) that allows direct operation from a high-voltage supply without a separate 5V regulator. The device runs from 2.0V to user-defined HV input with internal 4 MHz or 8 MHz oscillator options, providing flexible timing for cost-sensitive embedded designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, timers, I/O peripherals, and interrupt logic. Within the broader taxonomy, the PIC12HV609 belongs to the 8-bit microcontroller class -> RISC microcontroller family -> embedded controller -> semiconductor IC. The PIC12HV609 specifically sits in the PIC10/12/16 mid-range family, characterized by a 14-bit instruction word, 8-level hardware stack, and the lowest pin counts in the Microchip portfolio (6/8/14 pin). The "HV" prefix indicates the integrated shunt voltage regulator, which is the defining feature distinguishing it from the standard PIC12F609 variant. Key features include 5 general-purpose I/O pins plus 1 input-only pin with 25 mA source/sink capability for direct LED drive, individually programmable weak pull-ups, an analog comparator with programmable on-chip voltage reference, one 8-bit timer (TMR0), one 16-bit timer (TMR1), watchdog timer (WDT), enhanced power-on reset, brown-out reset (BOR), and in-circuit serial programming (ICSP). The wide operating voltage range and high-current I/O eliminate many external components typically required by competing MCUs. Architecture-wise, the device uses a Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and data access. The mid-range core executes one instruction per clock cycle (except branched instructions), delivering ~1 MIPS at 4 MHz. The integrated shunt regulator uses an external resistor network tied to the HV pin, providing regulated VDD for the core from a higher-voltage source. Typical applications include AC line-powered appliance control, LED lighting drivers, battery chargers, smart sensors, white goods control boards, and any cost-sensitive embedded application requiring a high-voltage-tolerant MCU without an external regulator. The high-voltage shunt simplifies isolated offline designs where a small switching supply feeds the HV pin directly. When designing with this part, choose the shunt resistor value based on the expected supply current (typically 4-50 mA range) and verify power dissipation in the shunt element. For battery applications where the HV input is not used, consider the PIC12F609 family instead to avoid quiescent current draw through the shunt path.

Cotización Contacto

PIC12HV609-E/SN

PIC12HV609-E/SN - 8-bit 20MHz MCU 1.75KB Flash | Microchip

The Microchip PIC12HV609-E/SN is an 8-bit Flash-based CMOS microcontroller in the PIC12 family, integrating 1.75 KB (1K x 14) of Flash program memory, 64 bytes of RAM, and a high-voltage shunt regulator on a single 8-pin SOIC die. It runs up to 20 MHz instruction rate from a wide 2.0V–5.5V supply, with the unique HV variant capable of operating directly from a 2.5V/3.3V/5V bus without a separate regulator stage. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that combines a CPU, non-volatile program memory (Flash), working RAM, and peripheral set into one package. Within the broader embedded hierarchy, the PIC12HV609 belongs to the PIC10/12/16 mid-range core family, itself a sub-family of Microchip's 8-bit PIC microcontrollers, which in turn sit inside the embedded MCU category of integrated circuits. The "HV" prefix indicates an integrated shunt regulator, allowing direct supply from higher-voltage rails without external regulation — a useful differentiator in low-component-count designs. Key features include an internal 4/8 MHz precision oscillator, a user-configurable comparator with hysteresis, one 8-bit timer (TMR0), one 16-bit timer (TMR1), a watchdog timer (WDT), brown-out reset (BOR), power-on reset (POR), in-circuit serial programming (ICSP), and 25 mA source/sink I/O drive. Six GPIO pins are available, of which five are multiplexed with analog comparator and timer inputs. The -E suffix denotes the extended -40 °C to +125 °C industrial temperature grade, and the /SN suffix specifies the 8-SOIC (3.90 mm) package. Architecturally, the device uses Microchip's 14-bit instruction word mid-range core with 8-level hardware stack and 35 instructions, providing deterministic interrupt latency and Harvard bus separation. The high-voltage shunt regulator on the VDD pin simplifies power design in battery and bus-powered applications where a low-cost Zener-resistor supply would otherwise be required. Typical applications include low-power sensor nodes, LED driver controllers, simple state machines, automotive body electronics (AEC-Q100 qualified), battery chargers, and consumer white-goods control. The wide voltage range and integrated HV regulator make it especially attractive for cost-sensitive 5 V or 12 V appliances and for replacing discrete logic plus Zener diode combinations. When designing with this device, note that only one comparator is provided — analog-heavy designs should consider the PIC12F617 or PIC12F1501 instead. Decoupling the VDD pin with a 100 nF ceramic capacitor placed within 3 mm of the pin is essential for stable HV regulator operation. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC12 family, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC12HV609-I/MF

PIC12HV609-I/MF - 8-Pin 1.75KB Flash 8-Bit MCU | Microchip

The Microchip Technology PIC12HV609-I/MF is an 8-pin, 8-bit CMOS Flash microcontroller with integrated high-voltage shunt regulator support, offering 1.75 KB (1K x 14) of program memory, 64 bytes of RAM, and 5 configurable I/O pins in a compact 8-VDFN (DFN-8) exposed-pad package. According to Microchip product information, the device operates from 2.0 V to 5.5 V (with high-voltage shunt operation up to 4.5 V regulated output) at internal clock speeds up to 20 MHz, supported by a factory-calibrated 4 MHz / 8 MHz internal oscillator option. An 8-bit PIC microcontroller (MCU) is a small, low-power computer-on-a-chip that integrates a CPU core, Flash program memory, RAM, peripherals, and I/O on a single die. The PIC12HV609 belongs to Microchip's PIC12F family of 8-pin microcontrollers, sitting in the broader taxonomy: PIC12F -> PIC10/12/16/18 family -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The HV variant adds an internal shunt regulator suitable for direct connection to higher-voltage supplies such as 12 V or 24 V industrial rails without an external regulator. Key features include 1.75 KB Flash program memory (1K x 14 words), 64 bytes data RAM, hardware multiply, six I/O with individual direction control, one 8-bit timer (TMR0) and one 16-bit timer (TMR1), an enhanced capture/compare/PWM (ECCP) module, an analog comparator, and a 4-channel 10-bit Analog-to-Digital Converter (ADC). The internal 8 MHz oscillator with PLL can be configured for 4 MHz or 8 MHz operation, eliminating the need for external crystals in cost-sensitive designs. The PIC12HV609-I/MF uses a RISC architecture with 35 single-cycle instructions (excluding branches), a 14-bit instruction word, and a 2-stage pipeline for deterministic execution. The HV shunt regulator block enables direct connection to 2.0 V - 5.5 V sources and supports high-voltage input via external shunt components for fan-control and appliance applications. Typical applications include small fan-speed controllers, DC-DC converter housekeeping, LED lighting control, battery chargers, smoke detectors, and general-purpose 8-bit embedded control in industrial and consumer products. The 8-VDFN package suits space-constrained surface-mount designs. When designing with this device, ensure the exposed thermal pad on the 8-VDFN package is soldered to the PCB ground plane for proper thermal dissipation. The HV input pin requires external shunt resistor selection per Microchip application note AN1031 to set the regulated rail voltage. This page synthesizes distributor pricing from DigiKey, Mouser, and LCSC, drop-in alternatives within the Microchip PIC12F family, and practical design notes not aggregated in any single source.

Cotización Contacto

PIC12HV609-I/MS

PIC12HV609-I/MS - 8-bit Flash MCU 1.75KB 20MHz MSOP-8 | Microchip

The Microchip Technology PIC12HV609-I/MS is an 8-bit flash-based CMOS microcontroller from the PIC® 12F family, housed in an 8-pin MSOP package with a 20 MHz maximum CPU clock, 1.75 KB (1K x 14 words) of flash program memory, and 64 bytes of data RAM. The 'HV' suffix indicates integrated high-voltage support that allows the device to operate directly from a 2.0 V to user-defined VDD source and to handle higher-voltage I/O switching through internal shunt regulator circuitry. An 8-bit PIC microcontroller is a RISC-class single-chip MCU built around a Harvard architecture with separate program and data buses. The PIC12F/12HV family targets low-pin-count, cost-sensitive embedded applications where minimal BOM, on-chip peripherals, and nanoWatt sleep modes outweigh the need for higher MIPS. In a typical product taxonomy: PIC12HV609 -> PIC12F series -> PIC12 family -> PIC10/12/14/16/18 mid-range 8-bit MCU lineup -> Microcontroller -> Microprocessors & Controllers -> Semiconductors. Each PIC12 core executes one instruction per clock cycle (excluding branches), delivering ~5 MIPS at 20 MHz. Key differentiating features include: 1.75 KB self-programmable flash with 100K endurance cycles, 64 bytes SRAM, 128 bytes EEPROM, an internal 8 MHz oscillator (with optional 31 kHz LF oscillator), six I/O pins with individual direction control, an 8-bit timer (TMR0) with an 8-bit prescaler, a 16-bit timer (TMR1), an enhanced PWM/capture/compare (ECCP) module, a 10-bit ADC with 4 input channels, a comparator with hysteresis, and the high-voltage shunt regulator that lets the chip run from 2.0 V-5.5 V with internal regulation. The MSOP-8 package has a typical theta-JA of ~206 C/W and supports industrial -40C to +85C operation. Architecturally, the device uses a 14-bit instruction word with a 35-instruction RISC core, an 8-level hardware stack, and Microchip's nanoWatt Technology for sub-microamp sleep currents. The HV shunt regulator eliminates the need for an external regulator in 9V/12V battery or industrial bus applications, while the integrated ADC and comparator allow direct sensor conditioning without an external analog front end. Typical applications include 9V/12V battery-powered sensor nodes, AC line-voltage zero-cross detection (via high-voltage tolerant I/O), fan-speed control loops, white-goods user-interface panels, and low-cost IR remote transmitters where the 20 MHz core delivers ample headroom for RC5/SIRC protocols. The HV regulator is also valuable in industrial 24V systems where the MCU can be powered directly from the bus through a series Zener. When designing with this part, ensure the HV shunt regulator's current limit (sometimes called 'zener current') is respected: total current draw through the regulator must remain within the device's specification, otherwise internal heating may exceed the package's thermal envelope. For designs not requiring high-voltage tolerance, the PIC12F609 in the same MSOP-8 pinout is a drop-in lower-cost option.

Cotización Contacto

PIC12HV609-I/P

PIC12HV609-I/P - 8-bit Flash MCU, 1.75KB Flash, 8MHz, PDIP-8

The Microchip Technology PIC12HV609-I/P is an 8-bit, 8-pin Flash-based CMOS microcontroller in the PIC12 mid-range family, supplied in a PDIP-8 (through-hole) package. It integrates 1.75 KB (1024 x 14) of self-programmable Flash program memory, 64 bytes of data RAM, and an internal 8 MHz oscillator (selectable to 4 MHz or 31 kHz LF), allowing standalone operation without an external crystal. The device supports supply voltages of 2.5 V, 3.3 V, or 5 V and is qualified for the industrial -40C to +85C operating range. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, I/O peripherals, and clock generation. The 8-bit PIC architecture uses a RISC instruction set with 35 single-word instructions and a 200 ns instruction cycle at 20 MHz, simplifying code generation in MPLAB X IDE while keeping deterministic real-time response. The PIC12 sub-family specifically targets space-constrained, low-pin-count applications such as appliance control, sensor front-ends, and battery-powered devices. Key features include four timers (Timer0, Timer1, Timer2, WDT), one enhanced Capture/Compare/PWM (ECCP) module, two analog comparators with selectable references, 6 general-purpose I/O pins, an internal shunt regulator for high-voltage operation (the "HV" suffix), Brown-Out Reset (BOR), Power-On Reset (POR), and an ICD debug interface. The PIC12HV609 is electrically identical to the PIC12F609 but adds an internal shunt regulator, allowing direct operation from supplies up to ~13.5 V without an external 5V regulator. Typical applications include LED lighting drivers, battery chargers, power-supply auxiliary controllers, smoke detectors, fan controls, and small appliance interfaces. The combination of Flash memory, internal oscillator, and high-voltage tolerance minimizes external component count. When designing with the PIC12HV609-I/P, verify that the high-voltage (HV) shunt current rating matches your supply; the internal shunt dissipates Vdd_delta * I_shunt. Always use a 0.1 uF decoupling capacitor within 5 mm of the Vdd pin and keep the ICSP clock/data traces short for reliable in-circuit programming. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto

PIC12HV609-I/SN

PIC12HV609-I/SN - 8-Bit 20MHz MCU, 1.75KB Flash, 8-SOIC | Microchip

The Microchip Technology PIC12HV609-I/SN is an 8-bit RISC flash microcontroller featuring the PIC12 CPU core, 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and a maximum operating frequency of 20MHz, housed in an 8-pin SOIC (SN) package with industrial -40C to +85C temperature grade. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip integrating a CPU, program memory, data RAM, and peripherals into a single silicon die. The PIC12HV609 belongs to the mid-range PIC12 family of 8-bit PIC microcontrollers, itself part of the larger PIC microcontroller hierarchy (PIC10/12/16/18) within the broader category of microcontrollers (MCU) and embedded computing ICs. Its defining feature is the 'HV' suffix, indicating integrated high-voltage shunt regulator support allowing direct operation from 2V to user-defined higher rails via an internal shunt regulator - unusual for 8-pin flash MCUs. Key features include a 20MHz internal/external clock, 8-bit architecture with 35 single-word instructions, four channels of 10-bit ADC, one 8-bit and one 16-bit timer, an internal voltage reference, and an enhanced capture/compare/PWM module. The HV variant integrates a 5.1V-13V shunt regulator on the supply pin, allowing direct connection to rectified mains or higher DC buses without an external regulator. Brown-out reset, power-on reset, and a watchdog timer provide system reliability. Designed for fan control, LED lighting, and high-voltage sensing applications, the PIC12HV609's enhanced PWM and integrated HV shunt simplify closed-loop BLDC and brushless fan designs. The Harvard RISC architecture executes instructions in a single cycle, achieving 200ns instruction time at 20MHz. Primary uses include BLDC ceiling fan motor control, AC-line-powered LED drivers, appliance controls, and low-cost high-voltage sensor interfaces. Industrial temperature range suits automotive and appliance environments. The 8-pin SOIC footprint enables compact designs while preserving easy hand-soldering. When designing with this device, ensure the shunt regulator current budget matches the application - the internal shunt dissipates excess voltage as heat. For AC mains rectification applications, isolate the digital logic from line-voltage transients with adequate PCB clearance and TVS protection. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto

PIC12HV609T-I/MD

PIC12HV609T-I/MD - 1.75KB Flash 8-bit MCU | Microchip | 8-DFN

The Microchip Technology PIC12HV609T-I/MD is an 8-bit flash-based CMOS microcontroller in the PIC12 family, offered in an 8-pin DFN-EP surface-mount package (3 x 3 mm, 0.90 mm height) and supplied on Tape and Reel. It integrates 1.75 KB of flash program memory, 64 bytes of RAM, and an internal 8 MHz oscillator, and operates across an industrial -40C to +85C temperature range at 2.5V/3.3V/5V supply rails. A PIC microcontroller (MCU) is a single-chip computer that combines a RISC CPU core, non-volatile flash program memory, RAM, and configurable peripherals around a compact die. The PIC12HV609 specifically is a low-pin-count (8-pin) member of Microchip's mid-range PIC family, optimized for cost-sensitive embedded applications where board area and BOM count matter more than raw computational throughput. It belongs to the broader hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. Key features of the PIC12HV609T-I/MD include a 20 MHz maximum CPU clock via the internal oscillator block, hardware timers (Timer0/Timer1/Timer2), a 10-bit Analog-to-Digital Converter (ADC) on selected pins, and a comparator with a programmable voltage reference. The "HV" suffix indicates an internal shunt voltage regulator that allows direct operation from higher-voltage supplies (such as 9V or 12V battery stacks) by regulating them down to the 5V internal rail. The device uses Microchip's enhanced mid-range 8-bit RISC architecture with 35 single-word instructions and a 14-bit instruction word. Two I/O pins are 5V-tolerant on most variants, supporting mixed-voltage digital interfaces. The on-chip in-circuit serial programming (ICSP) interface lets the same chip be programmed after PCB assembly using only two signal lines, eliminating programming sockets and reducing manufacturing cost. Typical applications include low-power sensor nodes, LED controllers, battery chargers, smoke detectors, and small appliance controls. The wide supply range (2.5V-5V) and built-in brown-out reset make it suitable for unregulated mains-powered or battery-powered systems. Industrial designs favor the -40C to +125C extended parts (PIC12HV609-E/MD), while the -I grade PIC12HV609T-I/MD is specified for commercial and light-industrial environments. A key design tip is that the internal shunt regulator of the "HV" variant dissipates significant power when fed from a high-voltage source. At 9V VIN and 5 mA internal draw, expect roughly 20 mW of continuous dissipation, so the exposed pad (EP) must be soldered to a copper pour for thermal relief. Layout this ground pad generously to keep junction temperature in check. This page synthesizes DigiKey distributor pricing, verified Microchip datasheet specs, same-package drop-in alternatives from Microchip's PIC12 family, and practical design guidance not found in any single distributor listing.

Cotización Contacto

Subcategorías

Productos (39.000+)

PIC12F675T-I/MD - 8-Bit 20MHz 1.75KB Flash MCU | Microchip

PIC12F675T-I/MF - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip

PIC12F675T-I/SN - 8-Bit 20MHz CMOS Flash MCU, 1.75KB | Microchip

PIC12F683-E/MD - 8-Bit 20MHz MCU 3.5KB Flash 8-DFN | Microchip

PIC12F683-E/P - 8-bit 20MHz 3.5KB Flash MCU | Microchip

PIC12F683-I/MD - 8-bit 20MHz MCU 3.5KB Flash 6 I/O | Microchip

PIC12F683-I/P - 8-Bit 20MHz MCU 3.5KB Flash | Microchip

PIC12F683-I/SN - 8-bit 20MHz 3.5KB Flash MCU | Microchip

PIC12F683T-E/MF - 8-Bit 20MHz 3.5KB Flash MCU | Microchip

PIC12F752-E/MF - 8-bit MCU 1.75KB Flash 6 I/O 20MHz | Microchip

PIC12F752-E/P - 8-Bit 5MIPS Flash MCU | Microchip Technology

PIC12F752-E/SN - 8-bit MCU, 1.75KB Flash, 6 I/O, 20MHz | Microchip

PIC12F752-I/MF - 8-Bit MCU 20MHz 1.75KB Flash 8-DFN | Microchip

PIC12F752-I/P - 8-bit MCU, 1.75KB Flash, 8-PDIP | Microchip

PIC12F752-I/SN - 20MHz 8-Bit Flash MCU | Microchip Technology

PIC12F752T-I/SN - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip

PIC12HV609-E/MS - 8-bit Flash MCU, 1.75KB, 8MSOP | Microchip

PIC12HV609-E/P - 8-bit Flash MCU, 1.75KB, 8-Pin PDIP | Microchip

PIC12HV609-E/SN - 8-bit 20MHz MCU 1.75KB Flash | Microchip

PIC12HV609-I/MF - 8-Pin 1.75KB Flash 8-Bit MCU | Microchip

PIC12HV609-I/MS - 8-bit Flash MCU 1.75KB 20MHz MSOP-8 | Microchip

PIC12HV609-I/P - 8-bit Flash MCU, 1.75KB Flash, 8MHz, PDIP-8

PIC12HV609-I/SN - 8-Bit 20MHz MCU, 1.75KB Flash, 8-SOIC | Microchip

PIC12HV609T-I/MD - 1.75KB Flash 8-bit MCU | Microchip | 8-DFN