Controladores LED
Productos (130)
PCA9633TK,118 - 4-bit 25mA I2C LED Driver HVSON8 | NXP
The NXP PCA9633TK,118 is a 4-bit 25 mA I2C-bus controlled LED driver optimized for Red/Green/Blue/Amber (RGBA) color mixing applications, housed in an 8-pin HVSON (3x3 mm) package. Each of the four LED outputs provides 8-bit resolution (256 steps) of fixed frequency PWM brightness control, and the device supports a 1 MHz Fast-Mode Plus (Fm+) I2C interface for high-speed host communication. A LED driver (Light-Emitting Diode driver) is an active electronic circuit that regulates current or voltage through one or more LEDs to set brightness, color mixing, and on/off timing. Within the broader power-management hierarchy, the PCA9633 sits under constant-current LED drivers -> LED drivers -> power management ICs -> semiconductors. The PCA9633TK variant uses voltage-switch (open-drain) outputs, making it well suited to driving low-voltage LEDs or external MOSFET-controlled higher-current strings while the host MCU retains color-mixing intelligence. Key differentiating features include per-output 8-bit PWM at 97.6 kHz nominal frequency to eliminate audible flicker in RGBA mixing, software-programmable output state inversion, group PWM/blink control, and a hardware-reset input with power-on reset. The wide 2.3 V-5.5 V supply range supports both 3.3 V and 5 V logic rails commonly found in RGB backlights and indicator panels. Architecturally the part uses an I2C slave state machine, a 4 MHz internal oscillator (divided down for PWM), and four open-drain output drivers rated at 25 mA continuous each. Outputs can be paralleled for higher current without external logic changes, and the device supports up to 126 selectable I2C addresses in the 16-pin version, enabling large addressable LED arrays. Typical applications include RGBA color-mixing for signage and architectural lighting, RGB keypad backlighting in consumer electronics, status indicators on networking hardware, and LED-blinking alert patterns on industrial HMIs. Designers choose this part when they need fine-grained PWM control of four low-current LEDs without an external driver FET. When designing, confirm that each LED's forward voltage does not exceed the open-drain pull-up tolerance and select a current-limit resistor (or constant-current driver) sized for the chosen LED bin. Decouple VDD with a 100 nF ceramic capacitor placed within 2 mm of the supply pin to suppress switching transients during PWM transitions. This page synthesizes distributor pricing, drop-in HVSON8 alternatives, and practical design considerations not consolidated on the manufacturer product page.
PCA9685PW - 16-Channel 12-bit PWM I2C LED Controller | NXP TSSOP-28
The NXP Semiconductors PCA9685PW is a 16-channel, 12-bit PWM Fm+ I2C-bus LED controller housed in a 28-pin TSSOP (SOT361-1) package, optimized for Red/Green/Blue/Amber (RGBA) color backlighting. Each of the 16 LED outputs has its own 12-bit resolution (4096 steps) fixed-frequency PWM controller that operates at a programmable frequency from typically 24 Hz to 1526 Hz, with a duty cycle adjustable from 0% to 100% for fine-grained brightness control. The device is rated for 25 mA sink current per output and operates from a 1 MHz Fast-Mode Plus I2C interface, allowing up to 62 devices to share a single bus via six hardware address pins. An LED driver is an integrated circuit that switches current through light-emitting diodes at controlled duty cycles and frequencies, allowing microcontrollers to drive many more LEDs than their limited GPIO pins can support directly. The PCA9685 belongs to the LED driver / PWM controller product family within the display driver hierarchy, which sits inside power management and lighting sub-systems. Compared to discrete MOSFETs driven by GPIO bit-banging, a dedicated LED controller IC delivers programmable frequency, smooth 12-bit dimming, hardware current sinking, and synchronized multi-channel phase shifting - critical for avoiding audible flicker and for removing the MCU's software timing burden. Key features include six hardware-selectable I2C addresses, a 1 MHz Fm+ capable SCL clock, programmable open-drain totem-pole output structure with 25 mA continuous sink, per-output 12-bit duty cycle plus 4-bit group Blink/Blink-at-fixed-frequency mode, and a 40 mA active-low Output Enable (OE) input for synchronized dimming via external PWM. The internal 25 MHz oscillator provides the time base and supports the wide 24 Hz - 1526 Hz PWM range with sub-percent duty cycle resolution. The PCA9685PW architecture combines an I2C slave decoder, a frequency prescaler, and 16 independent 12-bit PWM latches, all driven by a single on-chip 25 MHz RC oscillator. Outputs can be configured as totem-pole (push-pull) or open-drain, providing flexibility to drive both LED cathodes to GND and LED anodes to V+. The OE pin enables global phase-shifted PWM dimming - critical when multiple PCA9685PW ICs must be synchronized to a common refresh rate for large LED matrices. Typical applications include LCD TV/monitor RGBA LED backlighting, RGB LED strip driving, servo motor control via PWM (hobby robotics), LED matrix displays, and PC case lighting. Designers choose the PCA9685PW when they need more than the 4-6 PWM channels a typical MCU offers, require 12-bit dimming depth, or must chain multiple drivers on one I2C bus. When designing with this device, place the 220 nF bypass capacitor on VDD and the 1 uF + 2.2 uF bulk capacitors on V+ as close as possible to the pins, and keep the SDA/SCL traces short. The OE pin must be tied HIGH when not used; leaving it floating can cause undefined output behavior. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing a faster comparison surface for engineers evaluating LED controllers for backlight or robotics designs.
PD69101ILQ-TR - 1-Port PoE+ PSE Controller 802.3at | Microchip
The Microchip Technology PD69101ILQ-TR is a single-port, mixed-signal, high-voltage Power over Ethernet (PoE) PSE controller and manager supporting IEEE 802.3af (PoE) and IEEE 802.3at (PoE+) standards, delivering up to 30 W port power in a 24-pin QFN (4x5 mm) package with exposed pad, rated for industrial temperature ranges. A PoE PSE (Power Sourcing Equipment) controller is a power management IC that lives inside Ethernet switches, injectors, and midspans. It governs how power is safely delivered over the same Cat-5/Cat-6 cable that carries data: it detects whether a connected Powered Device (PD) is genuinely PoE-compliant, classifies its power draw, monitors current and voltage, and disconnects power safely when a device is removed. This prevents damage to legacy non-PoE equipment and ensures the Ethernet port never exceeds negotiated power budgets. The PD69101 provides detection of IEEE 802.3af-2003 compliant PDs and IEEE 802.3at high-power devices, ensuring safe power feeding and disconnection per the standard. Its mixed-signal architecture integrates the precision analog detection and classification circuitry with a management interface, and the MODE0/MODE1 configuration pins support a serial monitoring mode in which the device continuously transmits the content of nine internal registers for system health diagnostics. LED I/O pins support port-status indication. Typical applications include Ethernet switch ports, PoE midspan injectors, security camera and wireless access point infrastructure, and industrial network equipment where the industrial-grade temperature rating is required. Designers should budget port power dissipation: at a 30 W PoE+ port the datasheet example shows about 180 mW in the sense element and 108 mW in the external MOSFET at 600 mA, so an appropriate low-Rds(on) external pass MOSFET and sense resistor are key to thermal margin. The QFN-24 exposed pad must be soldered to a grounded copper pour for heat spreading. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-10-19.
PSSI2021SAY115 - 50mA Constant Current Source SOT-353 | Nexperia
The Nexperia PSSI2021SAY115 is a resistor-equipped PNP transistor integrated with two diodes on a single die, packaged in a 5-lead SOT-353 (SC-88A, UMT5) surface-mount housing, and function as a programmable constant current source. According to the Nexperia product page, it delivers a stabilized output current between 15 uA and 50 mA by selecting one external resistor between pins 4 and 5, with a maximum supply input of 75 V and a total power dissipation of 335 mW. The device is supplied on Tape & Reel (115 suffix) and is RoHS compliant, making it suitable for high-density automated assembly. A constant current source is a fundamental building block in modern electronics that delivers a load current independent of supply voltage, temperature, and load impedance variations. The PSSI2021SAY115 belongs to the discrete semiconductor family of current regulators, which sit hierarchically under transistors, then semiconductor devices. By integrating the bias resistor and two steering diodes together with the pass transistor on one chip, Nexperia eliminates the need for multiple discretes, reduces PCB area, and improves matching between the reference diodes and the PNP base-emitter junction. This integration delivers better temperature coefficient than discrete equivalents because the on-chip elements track each other across temperature. Key features include a wide programmable output range from 15 uA to 50 mA, a high 75 V input voltage rating for direct connection to industrial rails, low temperature drift due to monolithic construction, and a miniature SOT-353 footprint measuring only 2.0 x 1.25 mm. The device requires no additional bias network beyond the single external resistor, simplifying BOM and reducing design risk. Architecturally, the PSSI2021SAY115 uses the base-emitter junction of the PNP transistor as the reference element, with the two series diodes compensating the VBE temperature coefficient. The external resistor sets the reference current through the diodes, which is then mirrored to the output through the PNP pass transistor, providing the regulated load current. This topology provides stable biasing even at low output currents where discrete designs typically struggle. Typical applications include LED driver circuits, biasing of sensor bridges, precision reference currents for instrumentation amplifiers, battery chargers, and active loads. The SOT-353 package makes it particularly suitable for compact portable designs and high-density PCB layouts where board area is at a premium. When designing with this device, ensure the external resistor has a tolerance of 1% or better and adequate voltage rating. Power dissipation is calculated as (Vin - Vload) multiplied by Iout; verify this against the 335 mW maximum rating. The output pin should be decoupled with a small capacitor if driving fast transient loads to prevent oscillation. This page synthesizes distributor pricing, drop-in SOT-353 alternatives, and practical design notes that supplement the manufacturer datasheet, supporting both parametric searches and engineering reference workflows.
RT8462GS - High-Voltage LED Driver Controller | Richtek | Buck/Boost
The Richtek RT8462GS is a high-voltage, high-current LED driver controller built on a current-mode PWM architecture that drives an external MOSFET for high-power LED applications. The device integrates a 36 V rated input section with an output stage capable of 60 V, supports step-down (Buck), step-up (Boost), and step-down/step-up (Buck-Boost) topologies from a single 14-SOP package, and provides analog plus PWM dimming capability. Operating at a fixed switching frequency up to 1 MHz, the RT8462GS gives designers flexibility to optimize the inductor and EMI filter while still meeting tight current regulation across the load range. An LED driver controller is a power management integrated circuit (PMIC) that regulates the current flowing through a string of high-brightness LEDs. It belongs to the broader hierarchy of LED drivers -> power management IC -> power management -> semiconductor. Unlike a fixed-voltage regulator that targets a DC rail, an LED driver maintains constant current so that LED brightness and color temperature stay consistent regardless of supply variation, temperature drift, or forward-voltage bin spread. Key features of the RT8462GS include a low-side current sense amplifier with programmable threshold, an internal soft-start to limit inrush current, under-voltage lockout (UVLO), over-current protection (OCP), and over-temperature protection (OTP). The analog dimming input accepts a 0 to 1.2 V DC signal and the PWM dimming input accepts a TTL-level duty cycle from 100 Hz to 20 kHz, both supporting high-contrast dimming ratios needed for display backlight and architectural lighting. The RT8462GS uses peak current-mode control with a transconductance error amplifier referenced to an internal bandgap. The high-side gate driver output swings to the BST pin voltage, allowing use with logic-level N-channel MOSFETs. This topology provides simple loop compensation with a single Type-II network and inherent cycle-by-cycle current limiting. Typical applications include LCD monitor and TV LED backlight drivers, automotive interior and exterior lighting, architectural and stage lighting fixtures, and high-power portable lighting where efficiency and dimming flexibility matter. When designing with the RT8462GS, choose the external MOSFET and inductor to match the LED string current and switching frequency; ensure the BST capacitor and gate-drive resistor are sized per the manufacturer's typical application circuit. Provide adequate PCB copper for the power-stage ground return and route the current-sense traces as a Kelvin connection to avoid ground bounce. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet summary.
RT8475GS - 36V 350kHz LED Driver PWM Controller | Richtek
The Richtek RT8475GS is a current-mode PWM controller IC designed to drive an external MOSFET for high-current LED applications, housed in a 14-pin SOP (Small-Outline Package). With a current-sense amplifier threshold of 190 mV and a maximum operating input voltage of 36 V, the device supports output voltages up to 90 V, making it ideal for buck, boost, and buck-boost topologies in lighting and backlight designs. Typical switching frequency is 350 kHz, with an analog and PWM dimming control interface for brightness adjustment. An LED driver controller is a specialized power management IC that regulates the brightness of solid-state light sources by controlling the current flowing through one or more LEDs. Unlike simple resistor-based current limiters, an LED driver maintains constant current regardless of input voltage variation, temperature drift, or forward-voltage spread between LED batches. The RT8475GS falls into the PWM-controller sub-category of LED drivers (LED driver controller -> LED driver -> power management IC -> semiconductor), where it generates a PWM gate-drive signal for an external switching MOSFET rather than integrating the switch itself - giving designers freedom to choose MOSFET RDS(on), package, and thermal performance for high-power strings. Key features of the RT8475GS include analog and PWM dimming capability, a 350 kHz typical switching frequency that balances magnetics size against switching loss, and an enable/soft-start pin for controlled startup. The 190 mV low-side current-sense threshold minimizes losses on the sense resistor while preserving regulation, and the wide VIN range (4.5 V to 36 V) accommodates both 5 V/12 V bus systems and 24 V industrial rails. Analog dimming is supported via a linear DIM input, while PWM dimming accepts an external logic signal for high-contrast dimming ratios exceeding 1000:1. The RT8475GS uses a peak-current-mode control architecture with internal slope compensation, providing good line rejection, simple loop compensation, and cycle-by-cycle current limiting. The external MOSFET topology means designers can scale LED current simply by selecting a lower-inductance sense resistor (RSNS = 190 mV / ILED) - a critical advantage over integrated-switch LED drivers when currents exceed 1 A or when thermal budgets require spreading heat across the PCB rather than concentrating it inside the IC. Typical applications include high-brightness LED backlighting for LCD panels, architectural and stage lighting, automotive interior/exterior lighting, signage illumination, and DC/DC LED drivers in industrial machine-vision systems. The wide VIN range also suits portable lighting and battery-powered torches when paired with a boost topology. When designing with this controller, select the external MOSFET and inductor based on peak LED current, switching frequency (350 kHz), and maximum VIN. The sense resistor must be a low-inductance, low-drift type (1% tolerance or better), and the loop bandwidth should remain well below the switching frequency to avoid subharmonic oscillation when operating above 50% duty cycle. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from the same Richtek controller family, and practical design notes not found in the manufacturer datasheet.
RT8475ZS - 350kHz LED Driver Buck/Boost Controller | Richtek
The Richtek RT8475ZS is a 350 kHz constant-current LED driver controller with one DC-DC output supporting both step-down (Buck) and step-up (Boost) topologies, housed in a 14-pin SOP (Small Outline Package) with 3.90 mm body width. The device integrates analog and PWM dimming interfaces, making it suitable for driving high-brightness LED strings from a wide range of input voltages. According to distributor catalog descriptions, it functions as a PMIC LED Driver IC 1-Output DC-DC Controller with analog/PWM dimming in a 14-SOP package. An LED driver controller is a power management IC that regulates current through one or more strings of LEDs, maintaining brightness uniformity and protecting the LEDs from overcurrent conditions. In the broader taxonomy, LED driver controllers belong to PMIC -> power management IC -> driver IC -> constant-current regulator -> semiconductor. By regulating current rather than voltage, these controllers compensate for variations in LED forward voltage (Vf), temperature drift, and aging, ensuring consistent lumen output across the operating range. Key features of the RT8475ZS include its 350 kHz switching frequency, which keeps the converter above the AM band and allows compact inductor selection, and its dual topology flexibility (Buck or Boost) that lets a single part handle both step-down and step-up LED strings. The controller supports both analog dimming and PWM dimming, allowing brightness control from either a DC level or a duty-cycle signal for high-contrast dimming down to sub-1% levels. The 14-SOP package provides adequate thermal dissipation in surface-mount designs and supports standard reflow profiles. The RT8475ZS uses Richtek's proprietary constant-current control architecture to regulate the high-side MOSFET switch current through an external sense resistor, achieving cycle-by-cycle current limiting. The 350 kHz oscillator is internally trimmed, eliminating the need for an external RT resistor, and the dual dimming inputs (ADIM and PDIM) interface easily to microcontrollers or analog reference voltages. A typical application circuit uses an N-channel MOSFET, a Schottky diode, an inductor, and a sense resistor to form a complete buck or boost LED driver capable of driving strings of 1 W to 5 W LEDs. Typical applications include LED backlight drivers for LCD panels, architectural and decorative LED lighting, automotive interior lighting, and signage or indicator illumination. The wide input voltage tolerance of the controller supports both 12 V and 24 V bus systems commonly found in these applications. The analog dimming input is particularly useful for closed-loop feedback designs where ambient light sensing adjusts the LED current automatically. When designing with the RT8475ZS, ensure that the external MOSFET, inductor, and sense resistor are chosen for the target LED string voltage and current. PCB layout should minimize the loop area of the power stage to reduce EMI and use a ground plane for stable operation. The PWM dimming frequency should be selected above 100 Hz to avoid visible flicker in lighting applications. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes for the RT8475ZS, providing engineering guidance that goes beyond the standard distributor product listing.
SC600DIMLTRT - 120mA Dimming Charge-Pump LED Driver | Semtech
Semtech SC600DIMLTRT is a one-output, switched-capacitor charge-pump LED driver rated for 120 mA and packaged in a 10-lead MLPD measuring 3 x 3 mm. It accepts a 2.5 V to 6.5 V input range and offers selectable fixed outputs of 5.0 V, 4.5 V, or 4.0 V, depending on the specific device option. This version also supports LED dimming for portable-lighting and battery-powered products. A charge-pump LED driver is a power-management IC that transfers energy through switched capacitors rather than using an inductive DC-DC converter. This topology can provide a regulated LED drive voltage from a battery while avoiding the inductor used in a conventional buck or boost converter. The SC600 belongs to the LED-driver, DC-DC regulator, and power-management IC hierarchy. Key benefits include peak efficiency above 90%, short-circuit and over-temperature protection, a soft-start function, and shutdown current below 1 microamp. The small MLPD-10 package enables compact PCB layouts. The verified product listing identifies SC600DIMLTRT as a dimmable 120 mA LED driver, while the family datasheet describes 120 mA versions at 4.5 V and 4.0 V and 60 mA versions at other output settings. The SC600 uses a charge-pump topology to regulate the LED drive rail and includes selectable fixed output options. Soft start reduces the initial current surge during startup, while the protection functions improve robustness in portable applications. The exposed-pad package also requires attention to thermal layout when operating continuously near its rated current. Typical uses include battery-powered LED flashlights, portable lighting, status indicators, and compact consumer devices where a small, efficient LED drive voltage is useful. The 2.5 V to 6.5 V input range suits systems powered from one or more low-voltage cells. Dimming support makes the device relevant to products that need adjustable LED brightness. For PCB design, place the input, flying, and output capacitors close to their associated pins and follow the manufacturer’s recommended layout. Confirm the actual output-voltage option and pin configuration before placing a replacement. Keep exposed-pad copper available for thermal dissipation and verify startup, shutdown, dimming, and fault behavior in the finished system. This page consolidates verified distributor listings, the SC600 family datasheet information, package details, application guidance, and replacement-status notes. Pricing is referenced only where a verified amount was supplied; otherwise, request a current quote from XAIPART. The listed alternatives are functional comparison leads, not guaranteed drop-in replacements, because package and pin-level cross-reference data were not supplied.
SI3471A-A01-IMR - 90W 802.3bt PoE PSE Controller | Skyworks
The Skyworks Solutions SI3471A-A01-IMR is a single-channel Power over Ethernet (PoE) Power Sourcing Equipment (PSE) controller supporting IEEE 802.3af, 802.3at, and 802.3bt standards, delivering up to 90W per port in a 38-pin QFN (5x7 mm) package. A PoE PSE controller is the power-management device that lives on the switch or injector side of a PoE link. It is responsible for safely discovering whether a Powered Device (PD) is connected at the far end of the Ethernet cable, classifying its power requirement, and only then closing the internal or external MOSFET path to deliver power. The PSE controller hierarchy sits under power management ICs, and the Si3471 sits in its top tier because it implements the 802.3bt Type 4 / Class 8 specification, which raises per-port power to 90W using all four twisted pairs. Key features of the Si3471 include full IEEE 802.3bt compliance for detection, connection check, classification, and power-on sequencing, single-signature and dual-signature PD support, and operation across an industrial -40C to +85C temperature range. The controller supervises the pass MOSFETs and manages inrush current limiting, overcurrent protection, and fault reporting, all functions mandated by the IEEE standard and required for interoperability with certified PDs. Technically, the Si3471 follows the IEEE 802.3bt state machine for detection (two-point DC discovery), connection check, classification (including Layer 2 LLDP-based power negotiation handled at system level), and controlled power-on. The datasheet illustrates operation waveforms for both single-signature and dual-signature PD topologies, which determine whether power is delivered on two or four pairs and how the PD presents its detection signature. Typical applications include enterprise Ethernet switches, PoE midspan injectors, security camera and wireless access point infrastructure, and industrial networking equipment that must power 4-pair Class 8 loads such as PTZ cameras, video phones, and thin clients. A key design consideration is thermal management of the external pass MOSFETs at 90W: at a 54V PSE rail and typical PoE cable resistance, the controller itself dissipates little power, but Rds(on) of the external FETs directly drives port efficiency and connector temperature rise. This page synthesizes distributor pricing, verified specifications, ordering-option differences, and practical design notes not found in the manufacturer datasheet alone.
STLED316SMTR - 6-Digit LED Controller w/ Key Scan, SO-24 | STMicroelectronics
The STMicroelectronics STLED316SMTR is a serial-interfaced 6-digit LED controller with integrated key-scan, designed to drive 7-segment displays through a compact 3-wire SPI-compatible interface. It provides 14 constant-current sink outputs (8 segment lines + 6 digit lines) with 40 mA per-segment drive capability, while a 2x2 key-scan matrix supports up to 4 key inputs. The part operates from a 4.5 V to 5.5 V supply (3 V LED front-panel applications) and is offered in a 24-pin SO-24 small-outline surface-mount package with tape-and-reel packaging for high-volume assembly. What is an LED display controller? An LED display controller (sometimes called an LED driver or display bias IC) is an interface device that sits between a microcontroller and a multiplexed 7-segment or dot-matrix LED panel. It receives display data over a low-pin-count serial bus (SPI, I2C, or proprietary) and re-drives each segment at the correct duty cycle, freeing the host MCU from software multiplexing. In the broader taxonomy, LED display controllers sit beneath LED Drivers -> Power Management -> Power & Interface ICs, and they are distinct from simple LED current sinks because they integrate the timing, brightness, and key-scan logic required for human-machine interface (HMI) panels. Key features of the STLED316SMTR include 14 open-drain segment/digit outputs rated at 40 mA continuous, integrated 3-wire serial interface (clock, data, strobe) compatible with SPI mode 0, hardware key-scan with on-chip debounce, low standby current to support battery-backed panels, and a wide industrial operating temperature range. The device is also designed for minimum external BOM - only the segment current-setting resistor and decoupling caps are required, allowing very compact front-panel PCBs. Typical applications include white-good front panels (washing machines, microwaves, ovens), industrial control HMIs, point-of-sale (POS) terminals, audio equipment displays, instrument cluster readouts, and any 6-digit or smaller 7-segment user interface requiring keypad scanning. With 8 segment + 6 digit outputs the controller can drive a 6-digit 7-segment display plus decimal points, or up to 8 separate status LEDs. When designing with the STLED316SMTR, observe the absolute maximum segment current rating and choose the external RSET resistor accordingly. Ensure the 3-wire interface timing matches SPI mode 0 (CPOL=0, CPHA=0) of the host MCU, and place the decoupling capacitor as close as possible to VDD to suppress key-scan glitches during display multiplexing. This page synthesises distributor pricing, parametric comparison with same-brand and cross-brand drop-in alternatives, and practical design notes that complement - but do not replace - the official STMicroelectronics datasheet.
TAS5760L 21W Stereo I2S Class-D Audio Amplifier | TI
The Texas Instruments TAS5760L (TAS5760LDDCA) is a flexible, general-purpose stereo Class-D speaker amplifier with a digital I2S input serial audio port, delivering 21 W per channel in stereo or 42 W mono into a BTL load from a single 4.5 V to 16.4 V supply in a 48-pin HTSSOP package with exposed thermal pad. A Class-D audio amplifier is a switching amplifier that uses PWM modulation of power output stages to achieve efficiencies far above linear Class-AB designs, typically above 85-90 percent. Within the power-management and audio-signal-chain hierarchy, the TAS5760L sits between a digital audio source (SoC, DSP, or MCU with I2S/TDM output) and the loudspeaker, integrating DAC, processing, and power stage in one IC, reducing board area and EMI-filtering complexity compared to discrete solutions. Key features include both hardware-mode (strap-pin) and software-mode (I2C) control, an integrated digital clipper that protects speakers from overdriven signals, multiple gain settings, and two speed modes supporting a wide range of audio clock configurations. The 48-pin package also integrates a headphone or line-output driver path, eliminating an external DAC-headphone amplifier in many designs. Architecturally, the TAS5760L processes the incoming I2S stream digitally - including volume, EQ-based gain options, and clipping control - before driving a closed- or open-loop PWM power stage with integrated FETs. This digital-in architecture avoids the noise and mismatch of an external analog DAC-to-amp path and keeps the audio signal in the digital domain until final amplification. Typical applications include smart speakers and voice-assistant devices, portable Bluetooth speakers, soundbars, TV audio, and general-purpose powered-speaker designs. The wide 4.5 V to 16.4 V supply range covers single lithium-ion battery packs through 12 V wall adapters. Design tip: choose hardware mode for lowest BOM cost, but software mode (I2C) unlocks the full register set for volume, EQ, and diagnostics; always provide adequate copper area under the thermal pad for the 42 W mono condition.
TCA6507PW - 7-Bit I2C/SMBus LED Driver, 14-TSSOP | Texas Instruments
The Texas Instruments TCA6507PW is a 7-bit low-voltage LED driver with I2C and SMBus interface, supporting output current up to 40 mA per channel across 7 outputs in a 14-pin TSSOP (PW) package. It operates from a 1.65 V to 5.5 V supply range and is designed to control or dim LEDs through the two-wire bidirectional bus without continuous microcontroller involvement, freeing valuable processor time for other tasks. Background: A LED driver IC is a power-management semiconductor that regulates current through light-emitting diodes and provides brightness control. The TCA6507PW belongs to the I2C/SMBus-controlled LED driver category, which sits within the broader LED driver family inside power-management ICs. These devices relieve the host microcontroller from PWM-timing chores by generating the dimming waveform autonomously, while remaining configurable through a standard two-wire serial interface. Typical use cases are status indicators, keypad backlights, RGB funlights, and small LCD bias/supply chains. The 7-bit architecture means each of the seven outputs can be programmed independently, supporting combination of on/off and PWM brightness states simultaneously. Key features: seven programmable outputs selectable as on, off, slow on/off (programmable blink rates), or PWM dimming; software shutdown mode with a dedicated configuration register; per-pin 40 mA sink capability; 1.65 V to 5.5 V VCC range; integrated I2C/SMBus slave with selectable address; 25 mA quiescent current; and small-footprint 14-TSSOP (PW) package with 4.40 mm body width. The integrated brightness-control logic supports two user-selectable blink rates per output, allowing designers to mix steady-on indicators with blinking alerts without MCU overhead. Architecture: internally the TCA6507PW combines an I2C/SMBus-compatible serial interface, a bank of seven configurable output drivers with open-drain architecture, and a control register that selects between four modes per pin. The device operates as a slave on the I2C bus, with three address pins allowing up to eight TCA6507 devices on a single bus for expandability. The open-drain outputs can both sink current to drive LEDs tied to VCC, and accept logic-level inputs read back through the input register. Typical applications: LED status indication on routers/switches, mobile-phone keypad and funlight control, ultra-mobile PC indicator panels, industrial HMI status lamps, and any I2C/SMBus-backed multi-LED front panel. The TSSOP package suits compact handheld and space-constrained mainboards. Design consideration: place a 0.1 uF decoupling capacitor close to VCC (pin 14) and route the I2C SCL/SDA lines with 4.7 kohm pull-ups to the host-side VCC; the open-drain outputs require either an external resistor or a fixed load to VCC, never to GND, otherwise the LED will not illuminate. For multi-device buses, set the A0/A1/A2 address pins thoughtfully to avoid conflicts. Unique value: this page merges verified distributor pricing, parameter-validated drop-in alternatives, and PCB-level design guidance into one engineering-ready datasheet preview not present in the OEM datasheet alone.
TEA2096T - GreenChip Dual Synchronous Rectifier Controller | NXP
The NXP Semiconductors TEA2096T is a GreenChip dual synchronous rectifier (SR) controller IC for switched-mode power supplies, driving two SR MOSFETs from an 8-pin SO (SO-8) package with an adaptive gate drive method for maximum efficiency at any load. A synchronous rectifier controller replaces the conventional output diodes of an SMPS secondary side with MOSFETs, switching them on only when forward current flows. Because a modern low-RDS(on) MOSFET dissipates far less power than a Schottky diode at high current, SR control is a key efficiency lever in the power-supply hierarchy (SR controller -> power supply controller -> power management IC). The TEA2096T is a dedicated secondary-side controller for synchronous rectification on resonant converters, such as LLC and partially resonant (quasi-resonant) topologies used in high-efficiency adapters and supplies. Key features include two integrated driver stages for driving two SR MOSFETs, an adaptive gate-drive scheme that maximizes efficiency across the full load range, and GreenChip design principles that minimize standby and light-load losses. Dedicated sensing inputs allow the controller to detect the conduction state of each SR MOSFET and prevent cross-conduction and premature turn-off, which protects efficiency gains in continuous-conduction and burst modes. Technically, the device handles the challenging SR timing problem in resonant converters: because resonant tank current is sinusoidal, naive SR control causes body-diode conduction losses or reverse-current events. The TEA2096T adaptively adjusts turn-on and turn-off timing based on measured drain-source voltage behavior, ensuring the SR MOSFETs conduct only during the proper current interval. This is especially valuable at light load and in discontinuous operation, where fixed-timing SR controllers lose efficiency or risk shoot-through. Typical applications include LLC resonant converters in notebook adapters, USB-PD chargers, LED TV power supplies, server and telecom auxiliary supplies, and high-density industrial power modules where secondary-side diode loss dominates. Two driver channels allow a center-tapped secondary or full-wave SR arrangement from a single controller. Design consideration: proper layout of the sense connections is critical; keep the drain-sense traces short and away from gate-driver loops to avoid false triggering from dv/dt, and follow NXP layout guidance in the TEA2096T datasheet. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TLC5947DAPR - 24-Ch 12-Bit PWM LED Driver | Texas Instruments
The Texas Instruments TLC5947DAPR is a 24-channel, 12-bit constant-current sink LED driver with an internal oscillator, housed in a 32-pin HTSSOP (DAP) package with PowerPAD. Each of the 24 channels is individually adjustable with 4096 PWM grayscale steps, and the current of all 24 outputs is set by a single external resistor. Per-channel output current is rated at 30 mA. What is a constant-current LED driver? A constant-current LED driver is a specialized power management IC that regulates the current flowing through each LED string to a precise setpoint, regardless of variations in forward voltage, temperature, or supply voltage. Compared to a simple current-limiting resistor, it improves brightness uniformity, extends LED lifetime, and enables per-channel grayscale dimming. Constant-current sinks sit hierarchically inside LED drivers, which themselves are a sub-category of power management ICs alongside voltage regulators and battery management devices. The TLC5947DAPR further extends this role by adding 12-bit PWM grayscale control, dimming that circuit apart from any discrete MOSFET dimmer or boost-converter driver. Key differentiating features include 30 mA per-channel constant-current sinking, 12-bit (4096-step) PWM grayscale resolution, an internal oscillator that removes the need for an external PWM clock, a serial shift-register interface for cascaded multi-device chains, and integrated thermal shutdown. The wide VCC supply range supports battery and bus-powered designs, while 24 channels per IC minimize driver count in large LED matrices and signage. Architecturally, the TLC5947DAPR uses a serial-in/parallel-out shift register feeding 24 internal PWM counters that are clocked by the internal oscillator. Gray scale (GS) data is latched into the device via the serial interface and automatically replayed each PWM cycle, freeing the host microcontroller from continuous refresh. A single external IREF resistor sets the global current for all 24 channels, simplifying BOM while preserving per-pixel dimming accuracy. Typical applications include full-color LED video displays, RGB signage, architectural lighting, decorative and stage lighting, and large LED matrix backlighting. The cascading serial interface also makes it well suited to daisy-chained WS2812x-style "NeoPixel" replacement designs where deterministic, hardware-refreshed grayscale is required without MCU overhead. When designing with this device, place the IREF resistor close to the IREF pin to minimize noise pickup, and ensure the PowerPAD is soldered to a sufficient copper area (typically 1 square inch) to keep junction temperature within the 150 C thermal-shutdown limit under full 24-channel load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
TLC5955RTQR - 48-Ch 16-Bit PWM LED Driver w/ DC, BC | TI
The Texas Instruments TLC5955RTQR is a 48-channel, constant-current sink LED driver with 16-bit (65,536-step) PWM grayscale control, 7-bit (128-step) dot correction, and 8-bit brightness control, housed in a 56-pin QFN (RTQ) 8x8 mm package. It supports per-channel sink current up to 23.9 mA when VCC ≤ 3.6 V (MC = 5) and 31.9 mA when VCC > 3.6 V (MC = 7), with on-chip open/short LED detection. An LED driver is a specialized power-management IC that translates low-voltage digital brightness data into precisely regulated constant currents, allowing each LED in a matrix to be set to an exact luminance level. The TLC5955 belongs to the constant-current LED driver sub-category within Power Management ICs, sitting between generic GPIO expanders and high-voltage LED matrix drivers. It is typically used in displays where uniform brightness and fine grayscale steps matter more than raw current capability. Key features include 48 individually-controllable constant-current sink outputs, 16-bit Enhanced Spectrum or Conventional PWM grayscale, 7-bit dot correction that compensates brightness mismatch between LED channels, 8-bit global brightness control, on-chip circuitry that detects open or shorted LEDs failures in real time, an internal current setting register eliminating many external resistors, and a 30 MHz cascadable serial interface. The serial shift register design lets multiple TLC5955s share one SPI/QSPI bus for very large panels. Internally, the device uses a precision bandgap reference and matched current-mirror sinks. A global 8-bit brightness register scales all 48 channels simultaneously for overall panel brightness, while the 7-bit DC register fine-tunes each channel's bias current to mask LED forward-voltage variation. The 16-bit PWM counter is clocked from an external GS reference clock, and Enhanced Spectrum PWM spreads the switching edges across multiple sub-frames to reduce EMI peak energy. Open/short detection compares each output voltage against programmable thresholds between successive PWM refresh cycles without disturbing the panel image. Typical applications include full-color RGB LED video displays, indoor/outdoor LED signs, LED billboard panels, decorative architectural lighting, and stage lighting fixtures. The TLC5955 is especially well suited to high-channel-count panels where a single MCU cannot provide enough PWM pins and where uniform brightness across thousands of LEDs is critical. When designing with this part, route the GSCLK and SCLK lines as controlled-impedance traces and keep them away from the constant-current outputs to avoid coupling. Place the 0.1 µF VCC decoupling capacitor within 3 mm of the supply pin and follow the datasheet ground-plane recommendations. Note that VCC must be in the 3 V to 5.5 V range while the LED supply (VLED) can be higher, and the sink outputs can withstand up to 17 V per channel. This page consolidates distributor pricing, true drop-in alternatives, and practical design notes that go beyond the bare datasheet, giving an engineer a single reference for selecting and sourcing the TLC5955RTQR.
TLC6C5712QPWPRQ1 - 12-Ch AEC-Q100 LED Driver | Texas Instruments
The Texas Instruments TLC6C5712QPWPRQ1 is an automotive-grade 12-channel constant-current-sink LED driver with full diagnostics and PWM dimming, delivering up to 75 mA per channel from a 3 V to 5.5 V supply in a 28-pin HTSSOP (PWP) package. Per the TI product page, the device is qualified to AEC-Q100 for -40C to +125C operation. A constant-current-sink LED driver is a type of linear LED driver IC that regulates the current flowing through each LED string by sinking a precisely controlled current to ground. Within the power-management hierarchy, it sits under LED drivers -> linear current regulators -> power management ICs. Unlike simple resistive ballast or open-drain switches, a constant-current sink holds LED brightness constant despite forward-voltage variation, supply drift, and temperature change, which is essential for color and brightness consistency. Key features include 12 independent current-sink outputs rated at 75 mA each, PWM-based dimming for precise brightness control, and a comprehensive diagnostic suite that detects open-circuit, short-circuit, and other fault scenarios. TI designed this device specifically for safety-critical automotive cluster lighting, where system-level functional-safety considerations demand per-channel fault detection to maintain brightness and color-temperature consistency across many LEDs. Technically, the device uses a 12-bit architecture with internal current-setting registers and serial control, allowing the microcontroller to program per-channel current and read back diagnostic status. The current-sink topology is linear, adding no switching noise to the LED rails, while PWM dimming achieves wide-range average brightness without color shift. Output voltage rating of 7 V provides headroom for LED stack variation. Typical applications include automotive instrument-cluster backlighting, indicator and telltale LEDs, and other safety-critical multi-channel LED lighting in vehicles. The 12-channel density reduces BOM count versus discrete transistor solutions while adding diagnostics unavailable in discrete designs. A key design consideration is thermal dissipation: at 75 mA per channel with a large LED-headroom voltage, package power dissipation must be checked against the HTSSOP PowerPAD thermal capability, using copper pour under the pad. This page adds value beyond the datasheet by synthesizing distributor pricing, availability, drop-in alternative analysis, and practical design notes in one place.
TLC6C5724QPWPRQ1 - 24-Channel 50mA LED Driver, AEC-Q100 | TI
The Texas Instruments TLC6C5724QPWPRQ1 is an automotive-grade 24-channel constant-current RGB LED driver with full LED diagnostics, delivering up to 50 mA per output channel in a 38-pin HTSSOP (PWP) package with exposed pad. It features 7-bit dot correction with two ranges per output, 8-bit group intensity control per color group, and 12-, 10-, or 8-bit PWM dimming resolution. A constant-current LED driver is a type of power management IC that regulates current (rather than voltage) through LED strings. Because LED brightness and color depend directly on forward current, constant-current drivers eliminate the brightness variation that plagues simple resistive ballast designs. Within the power management hierarchy, the TLC6C5724-Q1 belongs to the linear LED driver family with integrated PWM dimming and dot correction, positioned as a system-level solution for matrix and string LED lighting control. Key differentiating features include the per-channel 7-bit dot correction with two selectable current ranges, which lets a single design compensate for LED forward-voltage binning across red, green, and blue dies; group-level 8-bit intensity control that simplifies color calibration; and a selectable 12-bit PWM engine supporting dimming ratios suited to automotive interior and exterior lighting. The full-diagnostics subsystem detects open-circuit and short-circuit LED faults, output shorts to GND, and provides fault reporting for functional-safety-oriented designs. Architecturally, the TLC6C5724-Q1 combines a constant-current sink per channel with an external resistor that sets the full-scale 50 mA maximum output current, a serial data interface for configuration, and an on-chip diagnostic engine that scans LED health during operation. Grayscale and dot-correction data are latched internally, allowing PWM dimming to continue glitch-free while new data shifts in, an important behavior for seamless brightness transitions. Typical applications include automotive RGB ambient interior lighting, rear combination lamps and turn indicators, architectural and accent lighting, and RGB status or backlighting in industrial displays. Its AEC-Q100 qualification and full diagnostics make it especially suitable for safety-relevant exterior lighting where fault reporting is required. When designing, set the external current-setting resistor so the 50 mA absolute maximum per-channel current is respected across temperature, and budget thermal dissipation for the worst-case channel currents in the exposed-pad HTSSOP package with an adequate copper pour. This page synthesizes verified distributor data, drop-in same-family alternatives, AEO-optimized FAQs, and practical design notes not found in the manufacturer datasheet.
TLD11141EPXUMA1 - 180mA 40V LITIX Basic+ LED Driver | Infineon
The Infineon TLD11141EPXUMA1 is a single-channel high-side LED driver IC from the LITIX Basic+ family, delivering up to 180 mA of regulated constant current to a high-side connected LED load from a 40 V supply rail, housed in a 14-pin PG-TSDSO-14 surface-mount package with exposed thermal pad. It integrates an output stage and a single-channel driver, supporting both DC operation and PWM dimming for accurate brightness control across automotive and industrial lighting. Background Knowledge: An LED driver IC is a specialized constant-current source that regulates the current through a high-brightness LED (HB-LED), protecting it from supply transients and thermal runaway while enabling brightness control. The category hierarchy is: LED driver -> lighting driver -> power management IC -> semiconductor. High-side drivers, like the TLD1114-1EP, place the current source between the supply rail and the LED anode, leaving the LED cathode at ground, which simplifies wiring in chassis-grounded systems and avoids ground-shift issues. This makes them ideal for automotive body and tail-light applications where one terminal is chassis-referenced. The TLD11141EPXUMA1 delivers up to 180 mA per channel, supports a wide 5.5 V to 40 V supply range (load-dump tolerant), and provides PWM dimming capability for variable brightness. Its integrated output stage minimizes external component count, while built-in protection features include over-temperature shutdown, short-circuit protection, and reverse-polarity robustness typical of Infineon's LITIX Basic+ family. The PG-TSDSO-14 exposed-pad package provides low thermal resistance, allowing reliable operation at the device's rated current. Internally, the device uses a precision bandgap reference and a current-sense architecture that regulates output current independent of LED forward voltage variations across temperature. The high-side drive topology simplifies PCB routing and supports parallel-channel configurations via multiple TLD1114-1EP devices for higher-current LED strings or multi-channel lighting systems. Typical applications include automotive tail lights, brake lights, daytime running lights (DRL), interior ambient lighting, status indicators, and industrial signage. The PWM dimming interface allows direct connection to a microcontroller for dynamic brightness adjustment, supporting safety features such as dynamic turn signals. When designing with this device, observe the maximum junction temperature rating and use adequate PCB copper area on the exposed pad to maintain thermal performance. Always verify the output current setting resistor value against the LED manufacturer's recommended forward current, and add an input capacitor close to the supply pin for load-dump and EMI robustness. This page synthesizes distributor stock data, drop-in alternative MPNs from the LITIX Basic+ family, and practical thermal/design guidance that goes beyond the manufacturer datasheet excerpts.
TLD1124ELXUMA1 - 360mA 1-Ch Linear LED Driver | Infineon LITIX
The Infineon TLD1124ELXUMA1 is a one-channel high-side linear LED driver IC from the LITIX™ Basic family, delivering up to 360 mA continuous output current to drive high-power LEDs in automotive lighting systems. Housed in a 14-pin PG-SSOP-14-EP (exposed pad) package, it integrates the output stage, current sense, and protection circuitry to provide a compact, robust solution for constant-current LED strings fed from a 5 V to 40 V supply rail. A linear LED driver (also called an LED controller or linear current regulator) is a power-management IC that maintains a constant, programmed current through an LED or LED string rather than a constant voltage. Within the broader power hierarchy, linear LED drivers sit beneath switching DC-DC LED drivers and above simple ballast resistors; they trade conversion efficiency for ultra-low EMI, fast PWM dimming response, and minimal external component count — making them the preferred topology for noise-sensitive or cost-sensitive automotive lamp modules. Key features of the TLD1124ELXUMA1 include an adjustable constant output current up to 360 mA set by a single external sense resistor, a wide supply range suited to automotive 12 V and 24 V bus systems, integrated PWM dimming via an enable/dimming input, and comprehensive protection including open-LED, short-to-GND, short-to-battery, over-temperature, and over-current diagnostics. The exposed thermal pad of the PG-SSOP-14-EP package provides a low θJA path to the PCB copper, which is essential when dissipating several watts in a linear topology. The device is qualified to AEC-Q100 for automotive use and is targeted at rear lamps, daytime running lights, interior mood lighting, and instrument-panel backlighting. Typical design tips: choose a sense resistor of roughly 0.5 Ω to 1.5 Ω to program the 360 mA nominal current, keep the input bypass capacitor within 5 mm of the VS pin, and connect the exposed pad to a copper area of at least 1 cm². This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
TLD1125ELXUMA1 - 1-Ch 360mA Linear LED Driver | Infineon LITIX
The Infineon TLD1125ELXUMA1 is a one-channel high-side constant-current LED driver IC from the LITIX Basic family, delivering up to 360 mA of regulated output current in a 14-pin PG-SSOP-14-EP package with exposed thermal pad. It is designed for linear driving of low- to medium-power LEDs in automotive and industrial lighting applications, with PWM dimming support for brightness control. What is a linear LED driver? A linear LED driver is a semiconductor device that regulates the current flowing through an LED string by dissipating excess voltage as heat across an internal pass element, instead of switching the inductor as a DC-DC converter does. Linear LED drivers sit within the broader power-management IC hierarchy: linear LED driver -> constant-current driver -> LED driver -> power management IC -> semiconductor. They are valued for low EMI, no inductor requirement, and very small PCB footprint, at the cost of reduced electrical efficiency compared to switching topologies. The TLD1125EL integrates an output stage that sustains load currents up to 360 mA, supports PWM dimming for precise brightness modulation, and includes protection features such as over-temperature shutdown, open-LED detection, and short-to-ground protection. Its 14-pin SSOP with exposed pad enables efficient heat removal on the PCB copper, which is essential because the linear topology converts the VIN-VLED drop into thermal energy. Automotive qualification per AEC-Q100 makes it directly suitable for tail lamps, daytime running lights (DRL), turn indicators, and interior ambient lighting. The output stage architecture combines a reference, error amplifier, and power transistor monolithically, achieving tight output-current accuracy and stable behavior across temperature. The exposed thermal pad (EP) on the bottom of the package provides a low thermal-resistance path to the PCB copper, enabling sustained high-current operation without external heatsinking. Typical applications include automotive rear combination lamps, turn signal indicators, daytime running lights, interior ambient lighting, and industrial signage or status indicators. Its footprint compatibility with other Infineon LITIX Basic family members allows platform reuse across lighting variants with different current ratings. When designing with this part, size the PCB copper pour beneath the exposed pad to keep the junction temperature below 150 C, and ensure that VIN does not exceed the absolute maximum rating even during load-dump transients. Place the decoupling capacitor close to the supply pin to stabilize the internal reference. This page synthesizes distributor pricing, pin-to-pin compatible alternatives, and practical design notes that supplement the manufacturer datasheet for faster engineering decisions.
TLD11731ETXUMA1 - 400mA Linear LED Driver | Infineon LITIX
The Infineon TLD11731ETXUMA1 is a single-channel low-side LED driver IC with 400 mA output current, packaged in a 16-pin PG-TFDSO-16-1 (TSSOP-16 exposed pad) surface-mount package. The device integrates a 1-channel linear current sink with PWM dimming support and Infineon's proprietary power shift feature for improved thermal performance in space-constrained automotive lighting modules. It is qualified to AEC-Q100 for automotive applications. A linear LED driver (constant-current sink) is a type of LED driver IC that regulates current through an LED string by dissipating excess voltage as heat, rather than switching it. Linear drivers sit within the broader LED driver IC category, alongside switching buck/boost LED drivers; they are preferred for applications where low EMI, no audible noise, and minimal external component count are priorities, at the cost of lower efficiency when VIN approaches VLED. They belong to the power management semiconductor family. Key features of the TLD11731ETXUMA1 include a wide input voltage range of 4.5 V to 40 V, an output voltage tolerance rated up to 36 V, 400 mA maximum output current per channel, integrated PWM dimming input, and the LITIX power shift feature that redistributes power dissipation for better thermal spreading. The exposed thermal pad enables direct PCB heatsinking without external heatsinks in typical automotive rear-light and interior-lighting layouts. The device uses a bipolar-based linear regulator architecture with internal control logic, current sense, and thermal protection circuitry. An internal reference and sense resistor set the output current; the device regulates the drop across its OUT pin to keep current constant regardless of LED forward-voltage variations. Thermal shutdown and load-disconnect protection improve system robustness against short-to-ground and open-load faults on the LED string. Typical applications include automotive rear combination lamps (tail, brake, turn), interior ambient lighting, dashboard backlighting, side-marker lights, daytime running light segments, and general-purpose industrial LED strips. The AEC-Q100 qualification plus wide 4.5 V–40 V input range also suits 12 V/24 V commercial-vehicle lighting. In power-rail systems, the TLD11731ETXUMA1 typically replaces discrete resistor-current-limit networks with a single IC, reducing PCB area and improving LED brightness uniformity. When designing with the TLD11731ETXUMA1, calculate worst-case power dissipation as PD = (VIN - VLED) x ILED and ensure the PCB copper area tied to the exposed pad keeps junction temperature below the thermal-shutdown threshold. The PWM dimming input accepts logic-level signals; for analog dimming, the device must be operated within its PWM duty-cycle range. This page synthesizes distributor pricing, drop-in alternatives from the Infineon LITIX family, and practical thermal/layout design notes not found in the manufacturer datasheet.
TLD1310ELXUMA1 - 3-Ch 120mA LED Driver LITIX Basic | Infineon
The Infineon TLD1310ELXUMA1 is a three-channel high-side LED driver IC from the LITIX Basic family, capable of driving up to 120 mA per channel with integrated output stages. Housed in a 14-pin PG-SSOP-14-5 package with exposed thermal pad, it is designed to control LEDs in automotive and industrial lighting applications where linear current regulation is preferred over switching topologies. What is an LED driver IC? An LED driver IC is a specialized power management integrated circuit that regulates the current flowing through one or more LED strings, maintaining constant brightness despite variations in supply voltage, temperature, and forward voltage. LED drivers are a subcategory of PMIC (Power Management IC) within the broader semiconductor hierarchy. High-side linear drivers like the TLD1310EL place the regulator between the supply and the LED load, providing accurate current control without the EMI emissions of switching converters. Key features of the TLD1310ELXUMA1 include three independently controlled constant-current output channels rated at up to 120 mA per channel, an operating supply voltage range compatible with 9V/12V/15V/18V/24V automotive systems, and an analog/digital dimming interface. The LITIX Basic architecture combines low dropout voltage with high current accuracy across the full automotive temperature range. The device also integrates protection features including open-load detection, short-to-ground detection, and over-temperature shutdown. The TLD1310EL uses bipolar transistor-based output stages with a precision bandgap reference, delivering stable current regulation even with large supply variations typical of automotive cranking and load-dump transients. The exposed pad PG-SSOP-14-5 package provides a low thermal resistance path, enabling sustained operation at high ambient temperatures. Built-in diagnostic outputs enable fault reporting to a host microcontroller. Typical applications include automotive rear combination lamps, turn indicators, daytime running lights (DRL), interior ambient lighting, and industrial signage. It is particularly suited for applications requiring AEC-Q100 qualification where multiple LED channels must be driven with precise current matching. When designing with this device, ensure that the supply voltage provides adequate headroom above the LED string forward voltage at full current. Use a low-ESR decoupling capacitor near the supply pin to suppress voltage transients on the automotive bus. The exposed pad must be soldered to a sufficient copper pour to dissipate heat at maximum load.
TLD21313EPXUMA1 - 3-Ch 60mA LED Driver, 40V LITIX Linear | Infineon
The Infineon TLD21313EPXUMA1 is a 3-channel linear current source LED driver from the LITIX family, delivering up to 60 mA per channel across an input voltage range of 5.5 V to 40 V, housed in a 14-pin PG-TSDSO-14 exposed-pad (TSSOP-14-EP) package. AEC-Q100 qualified, it is purpose-built for automotive exterior and interior lighting where a stable, regulated current is required to drive high-brightness LEDs from a fluctuating automotive supply rail. Each of the three outputs is independently PWM-dimmable, enabling precise brightness control for tail lamps, daytime running lights, and indicator functions. An LED driver IC is a specialized power management device that regulates the current flowing through an LED string, rather than simply setting the voltage. By forcing a constant current, the driver eliminates the brightness variation that would otherwise occur with temperature drift, supply fluctuation, or LED forward-voltage binning spread. Within the broader semiconductor taxonomy, the TLD21313EPXUMA1 belongs to the LITIX Linear family, which sits inside the Power Management IC (PMIC) category of linear LED drivers - a sub-class of voltage regulators that are optimized for low-noise, low-EMI current regulation rather than high-efficiency conversion. Key features include a 5% output current accuracy, integrated reverse-polarity protection, an enable/diagnostic pin, and built-in thermal shutdown with auto-recovery. The exposed thermal pad on the TSSOP-14-EP package keeps junction temperatures manageable even when all three channels are active at full 60 mA load, while the wide 5.5 V to 40 V input range tolerates load-dump transients common in 12 V and 24 V automotive systems. Typical applications include automotive rear combination lamps, turn indicators, brake lights, and interior ambient lighting, where the TLD21313EPXUMA1's combination of three independently dimmable channels in a single compact package reduces BOM cost and PCB area. Each output is driven by a constant-current sink, so the same board design can be reused across vehicle programs simply by changing the external sense resistor. When designing with this part, ensure the exposed pad is soldered to a sufficiently large copper pour to keep junction temperature below the thermal shutdown threshold. The PWM dimming input accepts logic-level signals, but a small RC filter on the PWMI pin reduces EMI. Designers should also leave adequate headroom above the LED string's total forward voltage to maintain constant-current regulation across the full dimming range. This page synthesizes distributor pricing, automotive-grade drop-in alternatives, and practical PCB layout guidance not collected in any single datasheet.
TLD21413EPXUMA1 - Triple 80mA LED Driver IC | Infineon
The Infineon TLD21413EPXUMA1 is a triple-channel high-side LED driver IC from the LITIX Basic+ family, providing three independent constant-current outputs of up to 80 mA per channel in a 14-pin PG-TSDSO-14 package with exposed thermal pad. It operates from a wide 5.5 V to 40 V supply range and supports PWM dimming via a dedicated DIM pin, with each output stage integrating a power transistor and current-setting reference for tight channel-to-channel matching. A high-side LED driver is a semiconductor device that sources current through an LED string from the positive supply rail while the LEDs sit between the driver output and ground. The high-side topology simplifies PCB routing by allowing multiple LED strings to share a common ground, eliminates ground-loop concerns, and enables per-string diagnostics. As a member of the LITIX Basic+ family, the TLD21413EPXUMA1 targets cost-sensitive automotive and industrial lighting where moderate current, fault detection, and small PCB area are critical requirements. Key features include 80 mA per channel continuous output current (60 mA per the typical-application range), built-in PWM dimming capability down to low duty cycles, three independently controlled constant-current outputs, integrated reverse-polarity protection, and an exposed-pad TSSOP-14 package providing low thermal resistance for sustained high-current operation. Each output stage is trimmed to deliver accurate, channel-matched current without external ballast resistors, which simplifies BOM and improves reliability. The TLD21413EPXUMA1 uses a precision bandgap reference and matched output transistors to achieve tight current regulation across load, supply, and temperature variations. The high-side current source architecture allows the device to drive LEDs connected to chassis ground, simplifying harness design in automotive rear-combination lamps, signal light modules, and interior RGB ambient lighting strips where channel independence and low EMI are mandatory. Typical applications include automotive rear lighting (tail, brake, turn signal), RGB ambient interior lighting, status indicator clusters, decorative LED strips, and general industrial signage. The wide 5.5 V to 40 V input range also supports 12 V and 24 V vehicle buses directly without additional pre-regulation. When designing with the TLD21413EPXUMA1, observe the thermal limits of the PG-TSDSO-14 exposed pad and place sufficient copper pour on the PCB to dissipate up to 1 W per channel. The DIM pin accepts a PWM signal at logic levels; ensure the dimming frequency is below the device's specified maximum to avoid output-stage ringing. This page consolidates distributor pricing, drop-in compatible LITIX Basic+ alternatives, and practical PCB/thermal design notes - engineering content that goes beyond what is summarized in the manufacturer datasheet.