Microcontroladores

Productos (20.000+)

MC9S12A256MPVE - 16-bit HCS12 MCU, 256KB Flash, 25MHz | NXP
MC9S12A256MPVE

MC9S12A256MPVE - 16-bit HCS12 MCU, 256KB Flash, 25MHz | NXP

The NXP MC9S12A256MPVE is a 16-bit microcontroller based on the HCS12 CPU core, delivering 25 MHz performance with 256 KB on-chip Flash and 12 KB RAM in a 112-pin LQFP (20x20 mm) package. Marked NXP as NRND (Not Recommended for New Designs), this BARRACUDA4 family member integrates a rich set of on-chip peripherals designed for automotive and industrial embedded applications. A microcontroller (MCU) is an integrated circuit containing a processor, memory (Flash for program storage and RAM for working storage), and programmable I/O peripherals on a single die. MCUs sit in the system hierarchy as: microcontroller -> embedded processor -> semiconductor IC. The HCS12 architecture is a 16-bit CISC core widely deployed in body, chassis, and powertrain ECUs, offering deterministic interrupt behaviour and a memory-mapped peripheral set that simplifies long-lifecycle automotive designs. Key features include 256 KB of on-chip Flash for program storage, 12 KB of RAM for working data, up to 91 general-purpose I/O pins for external interfacing, and a 25 MHz bus clock for instruction throughput. Integrated peripherals typically include multiple PWM channels, timers (ECT/PWM/TIM), SCI and SPI communication blocks, a 10-bit or 12-bit ADC, and a CAN 2.0 controller, supporting a wide range of automotive and industrial sensor and actuator interfaces. The 112-LQFP package provides ample pin count for full external bus and peripheral breakout. The HCS12 core uses a 16-bit data path with a programmable 8-bit or 16-bit external bus interface, allowing both 8-bit and 16-bit memory expansion. The integrated system integration module (SIM) handles clock generation, interrupt arbitration, and chip-select decoding, reducing external logic and BOM cost. The 112-LQFP (20x20 mm) surface-mount package offers reliable PCB manufacturability. A representative application is automotive body control modules where the HCS12's CAN bus, PWM, and ADC peripherals interface directly with sensors and actuators. Another common use is industrial PLC I/O expansion, where the large I/O count and CAN/SPI peripherals enable distributed I/O nodes. Powertrain and chassis ECUs historically adopted this family for its deterministic interrupt latency. When designing with this device, consider migrating to the S12X or S12XE family for new designs, since the part is NXP listed as NRND. Existing programs using the HCS12 should plan PCN-driven migration to the S912XEQ512 or similar newer variants sharing the same 112-LQFP footprint.

Cotización Contacto
MC9S12A32CFUE - 16-bit HCS12 MCU 32KB Flash 80-QFP | NXP
MC9S12A32CFUE

MC9S12A32CFUE - 16-bit HCS12 MCU 32KB Flash 80-QFP | NXP

The NXP Semiconductors MC9S12A32CFUE is a 16-bit HCS12 microcontroller (MCU) running at up to 25 MHz with 32KB of FLASH program memory, 4KB of RAM, and a 2.97V to 5.5V supply range, housed in an 80-pin QFP (14x14 mm) surface-mount package. A 16-bit microcontroller is a single-chip computer whose CPU processes 16-bit data words, sitting above 8-bit MCUs (better math throughput, larger address space) and below 32-bit MCUs (lower cost and complexity). The S12A family belongs to the HCS12 (S12) architecture originally developed by Freescale Semiconductor, now part of NXP, and is a member of the broader automotive and industrial microcontroller / embedded processor hierarchy. Full 16-bit data paths run throughout the core, managed by a system integration module (SIM) that handles resource mapping, clock generation, interrupt control, and bus interfacing. Key features include the CISC HCS12 CPU core clocked at 25 MHz, 32KB (32K x 8) on-chip FLASH with in-application reprogrammability, 4KB RAM, an on-chip phase-locked loop (PLL) that lets the core run faster than the reference crystal to cut power consumption and EMI, and a 10-bit ADC. The wide 2.5V/5V supply class and automotive-grade pedigree make it tolerant of harsh electrical environments. Architecturally, the S12A integrates standard on-chip peripherals around the HCS12 core, with the external bus capable of operating in an 8-bit narrow mode so single 8-bit-wide memories can be interfaced - useful for cost-optimized system expansions. The PLL-based clock generation allows designers to trade bus speed against current draw dynamically. Typical applications include automotive body electronics (door modules, seat control, lighting), industrial control and motor management, building automation, and legacy HCS12 system maintenance, where proven 5V-tolerant I/O and mature toolchains are valued. Design consideration: since this device is NRND (Not Recommended for New Designs) per NXP, plan second-source migration to the S12G or S12P families for new projects, and verify FLASH endurance budgets for applications with frequent reprogramming. This page synthesizes distributor pricing, drop-in family alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
MC9S12A512CPVE - 16-bit HCS12 MCU 512KB Flash | NXP
MC9S12A512CPVE

MC9S12A512CPVE - 16-bit HCS12 MCU 512KB Flash | NXP

The NXP Semiconductors MC9S12A512CPVE is a 16-bit HCS12 microcontroller with 512KB of Flash memory, 25 MHz bus operation, and an 8-channel 10-bit ADC, housed in a 112-pin LQFP (20x20 mm) package. It is AEC-Q100 qualified for automotive applications and ships in tray packaging. A 16-bit microcontroller is a single-chip embedded processor whose arithmetic logic unit and data paths are 16 bits wide, sitting between 8-bit MCUs (low cost, simple control) and 32-bit MCUs (high computation, connectivity). Within the power-management and embedded-control hierarchy, the HCS12 (S12) family - originally developed by Motorola and Freescale Semiconductor, now NXP - is a CISC-derived architecture widely used for body electronics, instrumentation, and motor control. The MC9S12A512 belongs to the Whaleshark/A-family of S12 devices, where the System Integration Module (SIM) manages resource mapping, clock generation, interrupt control, and bus interfacing. Key features include 512KB (512K x 8) of on-chip Flash program memory, full 16-bit data paths with a 25 MHz bus clock, and an external bus that can operate in an 8-bit narrow mode so single 8-bit-wide memories can be interfaced. This narrow-mode capability reduces external bus cost in cost-sensitive designs. The device also integrates standard on-chip peripherals typical of the S12 platform, including serial communication interfaces (SCI), serial peripheral interface (SPI), I2C bus, timer modules with PWM outputs, and an 8-channel 10-bit analog-to-digital converter. Architecturally, the enhanced HCS12 CPU executes a CISC instruction set with dense, byte-efficient code, which suits legacy code reuse and long-life automotive platforms. On-chip Flash with in-application programming supports field updates, while the PLL-based clock generation allows an external low-frequency crystal to generate the 25 MHz internal bus frequency, reducing EMI. Typical applications include automotive body control modules, instrument clusters, industrial control systems, HVAC controllers, and motor control nodes - anywhere a rugged 16-bit MCU with large on-chip Flash and AEC-Q100 qualification is required. The wide 5V-tolerant I/O ecosystem makes it easy to interface with legacy sensors and actuators. One key design consideration is supply architecture: the device uses separate 5V and internal 2.5V regulator domains, so follow NXP layout guidance for VDDA/VSSA decoupling and the low-EMI PLL filter network. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
MC9S12A64CFUE - HCS12 16-bit MCU, 64KB Flash, 25MHz, 80-QFP | NXP
MC9S12A64CFUE

MC9S12A64CFUE - HCS12 16-bit MCU, 64KB Flash, 25MHz, 80-QFP | NXP

The NXP Semiconductors MC9S12A64CFUE is a 16-bit HCS12 microcontroller unit (MCU) operating at up to 25 MHz, integrating 64 KB of on-chip Flash, 4 KB of RAM and 1 KB of EEPROM in an 80-pin QFP (14x14 mm) package. It belongs to the S12A family, an enhanced HCS12 core with CISC architecture designed for cost-sensitive automotive body and chassis electronics. An MCU (microcontroller unit) is a single-chip computer containing a CPU, memory and programmable peripherals, used to sense, decide and actuate in embedded systems. Within the broader semiconductor taxonomy, the MC9S12A64CFUE sits in the chain: microcontroller -> embedded MCU -> 16-bit MCU -> HCS12 family -> S12A sub-family -> automotive-grade body controller. The HCS12 core itself descended from the Freescale (now NXP) HC12, optimized for deterministic interrupt response and 16-bit arithmetic in real-time control loops. Key features include a 25 MHz bus clock, an 8-channel 10-bit ADC, two SCI (UART) channels, one SPI port, one I2C bus, a CAN 2.0 A/B controller, an 8-channel 16-bit PWM module with centre- or edge-aligned modes, and 59 general-purpose I/O lines multiplexed across the 80-QFP. The device includes a 4-channel TIM (ECT) timer, a periodic interrupt timer, an 8-bit accelerometer-friendly PWM, a watchdog timer, and on-chip voltage regulation allowing single 5 V supply operation from 2.35 V to 5.25 V. Architecturally the part uses a 16-bit data path internally, with an external bus interface that can be configured to 8-bit narrow mode for low-cost memory expansion. The 64 KB Flash is organised as a single linear array with EEPROM for non-volatile user data and a security lock mechanism to protect firmware IP. Typical applications include automotive body controllers (door modules, seat controllers, mirror adjusters, HVAC panels), industrial CAN nodes, building automation gateways, low-speed sensor hubs, and appliance motor controllers that benefit from CAN connectivity and PWM-driven H-bridge control. The wide operating voltage range and automotive temperature grade (AEC-Q100 qualified) make it well suited to 12 V automotive battery environments. When designing with this MCU, allocate the 64 KB Flash carefully: bootloader plus application typically leaves 32-48 KB for code. Use BDM (Background Debug Mode) via the dedicated BKGD pin for in-circuit programming and debug, and ensure the CAN bus termination and transceiver (e.g. TJA1050) are matched to the MCU's internal CAN controller. This page synthesises distributor pricing, drop-in S12A-family alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
MC9S12A64CPVE - 16-bit HCS12 MCU 64KB Flash 25MHz | NXP
MC9S12A64CPVE

MC9S12A64CPVE - 16-bit HCS12 MCU 64KB Flash 25MHz | NXP

The NXP Semiconductors MC9S12A64CPVE is a 16-bit HCS12 microcontroller with a 25 MHz bus, 64KB of on-chip Flash memory, and a 112-pin LQFP (20x20 mm) package. The device integrates standard on-chip peripherals managed by the system integration module (SIM), with full 16-bit data paths throughout. A 16-bit microcontroller (MCU) is a complete computing system on a single chip that combines a processor core, program memory, data memory, and peripheral functions such as timers, serial interfaces, and analog-to-digital converters. Within the MCU hierarchy, the HCS12 family sits in the broader 16-bit embedded controller category, descending from the Freescale (Motorola) HC12 and 68HC11 lineage that has served industrial and automotive platforms for decades. NXP, which acquired Freescale Semiconductor, continues to supply this family for legacy designs. Key features of the MC9S12A64CPVE include the HCS12 CPU core with CISC instruction set, 64KB (64K x 8) of Flash program memory, and a maximum bus frequency of 25 MHz. The system integration module handles resource mapping, clock generation, interrupt control, and bus interfacing. An external bus narrow mode allows the 16-bit bus to operate in 8-bit mode, enabling interfacing with single 8-bit-wide external memory devices. The architecture provides a 2.5V/5V supply environment per cross-reference data, with the core and I/O engineered around the classic 5V-tolerant HCS12 electrical profile that made the family popular in noisy automotive and industrial environments where 5V signaling remains standard. Peripherals typically found across the S12A family include SCI serial ports, SPI, an ATD analog-to-digital converter, timer channels, and PWM outputs, all controlled through memory-mapped registers. Typical applications include automotive body electronics, industrial control systems, motor control nodes, instrumentation, and legacy product lines requiring continued sourcing of proven HCS12 silicon. The 112-pin LQFP offers generous I/O count for relays, sensors, and communication expansion. Design consideration: this part is classified NRND (Not Recommended for New Designs) by NXP, so new designs should evaluate S12G, S12Z, or MagniV successors, while existing designs can continue to source this part for maintenance. This page synthesizes distributor pricing, drop-in alternatives within the S12 family, and practical design notes not found in the manufacturer datasheet, with pricing data as of 2026-10-18.

Cotización Contacto
MC9S12B128CFUE - 16-bit S12 MCU, 128KB Flash, 25MHz | NXP
MC9S12B128CFUE

MC9S12B128CFUE - 16-bit S12 MCU, 128KB Flash, 25MHz | NXP

The NXP MC9S12B128CFUE is a 16-bit HCS12 (S12B) microcontroller featuring 128 KB on-chip Flash, 25 MHz bus clock, and a wide peripheral set, housed in an 80-pin LQFP (14x14 mm) package. Designed for automotive multiplexing applications, it operates across -40C to +85C and integrates a CAN 2.0 module, multiple SCI/SPI ports, timers, and an 8-channel 10-bit ADC. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program and data memory, peripherals, and I/O on a single die. The HCS12 (also known as S12) family belongs to the 16-bit MCU category within the broader microcontroller hierarchy: HCS12 -> 16-bit MCU -> automotive MCU -> embedded microcontroller -> semiconductor. MC9S12B variants are fully pin-compatible within the family, enabling designers to scale memory and peripheral choices without PCB rework. Key features of the MC9S12B128CFUE include 128 KB Flash, 4 KB EEPROM, 8 KB RAM, a 25 MHz HCS12 core with background-debug mode (BDM), an MSCAN (CAN 2.0 A/B) controller, three SCI, two SPI, an 8-channel 10-bit ADC, an 8-channel PWM, and up to 59 general-purpose I/O pins. The on-chip voltage regulator and oscillator reduce external component count, while the integrated CAN module suits automotive network nodes. Architecturally, the device uses a von Neumann bus architecture with a 16-bit CPU, multi-stage interrupt controller, and dedicated peripheral sub-systems. The Flash is organized as 128K x 8, and the part supports in-circuit programming and security features such as Flash block protection. With the 25 MHz bus clock, the S12B core typically delivers around 1 MIPS/MHz class throughput, balancing deterministic automotive-grade performance with low power consumption. Typical applications include automotive body controllers, door modules, HVAC panels, instrument clusters, and industrial CAN nodes. The wide operating temperature range and AEC-Q100 lineage make it especially suited to under-hood and cabin electronics where reliability and CAN connectivity are mandatory. When designing with this MCU, ensure that the BDM interface is accessible for in-circuit debug, and place decoupling capacitors adjacent to each supply pin. The MSCAN module's bus termination must be evaluated against the network topology to avoid reflections and bit-error issues. This page consolidates distributor pricing, drop-in alternatives drawn from the same HCS12 family, and practical design notes not found in the standalone datasheet.

Cotización Contacto
MC9S12B128MFU - 16-Bit 50MHz 128KB Flash MCU | NXP
MC9S12B128MFU

MC9S12B128MFU - 16-Bit 50MHz 128KB Flash MCU | NXP

The NXP Semiconductors MC9S12B128MFU is a 16-bit, 50 MHz flash-based microcontroller with 128 KB of program memory, supplied in an 80-pin QFP package measuring 14 x 14 mm. It belongs to the MC9S12B automotive-multiplexing family and is intended for embedded control systems requiring deterministic real-time performance, broad peripheral integration, and scalable family-compatible pin assignments. A microcontroller is a semiconductor that integrates a processor core, nonvolatile program memory, data memory, timers, communication interfaces, and input/output ports onto one device. Within the product hierarchy, the MC9S12B128MFU is a 16-bit MCU, a flash-based embedded controller, and an automotive-oriented system-on-chip. Its integration reduces external component count while providing dedicated resources for body, vehicle-network, and industrial control functions. The verified source data identifies a 50 MHz operating frequency, 16-bit architecture, and 128 KB organized as 128K x 8 flash memory. The family documentation states that MC9S12B devices are designed for automotive multiplexing applications and are fully pin compatible, enabling different memory and peripheral options within a scalable design platform. That family-level compatibility is useful when products need common hardware across multiple MCU variants. The 80-QFP mechanical format provides a fine-pitch surface-mount solution with external pins on all four sides. Compared with a higher pin-count ball-grid-array package, the QFP simplifies visual inspection, rework, and prototype assembly, although it requires careful board-level escape routing. Its 14 x 14 mm body saves board area relative to many larger legacy packages while remaining compatible with established automated assembly processes. Typical uses include automotive body-control modules, multiplexing controllers, sensor-interface nodes, actuator controllers, and other embedded systems that benefit from a deterministic 16-bit architecture. In these systems, the MCU can acquire sensor inputs, execute control logic, manage timers and communication events, and drive external circuitry from a single integrated device. Detailed peripheral assignments, voltage limits, memory-map behavior, and electrical conditions must be confirmed in the manufacturer datasheet before design release. When laying out a new board, preserve the package land pattern, pin assignment, power distribution, decoupling, programming access, and exposed support-network requirements of the exact ordered device. Do not assume that every member of the MC9S12B family is a drop-in replacement solely because the family is pin compatible; memory capacity, package suffix, clocking, peripherals, and software device configuration can differ. This page consolidates verified distributor specifications, family-level application context, sourcing information, and design cautions. It also separates known facts from unavailable data rather than estimating unverified electrical limits, pricing, pin functions, lifecycle status, or cross-device compatibility.

Cotización Contacto
MC9S12B128MFUE - 16-bit HCS12 MCU, 128KB Flash, 25MHz | NXP
MC9S12B128MFUE

MC9S12B128MFUE - 16-bit HCS12 MCU, 128KB Flash, 25MHz | NXP

The NXP MC9S12B128MFUE is a 16-bit HCS12 microcontroller with 128KB Flash, 25MHz CPU, and 80-pin QFP package, AEC-Q100 qualified for automotive multiplexing. An HCS12 microcontroller is a 16-bit automotive-grade MCU built on the Freescale/NXP HCS12 CPU core. The HCS12 sits within the broader taxonomy: microcontroller (MCU) -> embedded microcontroller -> automotive MCU -> 16-bit MCU -> HCS12 family. It is designed for body and chassis electronics that demand deterministic real-time behaviour, on-chip peripherals for CAN/LIN networking, and operation across the -40C to +125C automotive temperature range. Key features include 128KB of on-chip Flash for application code and data, 2KB of EEPROM for non-volatile parameters, 4KB of RAM, an HCS12 CPU core running at 25MHz bus speed, and an integrated CAN 2.0 module plus multiple SCI/SPI peripherals. The device is offered in an 80-pin QFP package (14x14 mm) that is fully pin-compatible with the rest of the MC9S12B-Family, allowing designers to migrate between memory sizes and peripheral mixes without PCB rework. The MC9S12B128MFUE is built on NXP's 0.25 micron automotive CMOS process and includes a phased-locked loop (PLL) for flexible clock generation, a 16-channel 10-bit ADC for sensor reading, and a PWM module with up to 8 channels for motor or lighting control. Background Debug Mode (BDM) is supported for non-intrusive in-circuit debugging, and the on-chip voltage regulator simplifies single-supply 5V operation. Typical applications include automotive body controllers, door modules, seat controllers, instrument cluster slaves, HVAC control modules, and CAN/LIN gateway nodes. Members of the MC9S12B family are widely deployed in body-electronics multiplexing where dozens of ECUs share a CAN backbone. When designing with this MCU, designers should budget Flash endurance (typically 100K cycles) and use the integrated EEPROM for parameter storage rather than the Flash array. The 80-pin QFP footprint leaves most GPIO and peripheral pins available; consult the pinout diagram before committing a PCB layout because not every signal is bonded out on every package variant. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a one-stop reference for sourcing the MC9S12B128MFUE.

Cotización Contacto
MC9S12B128MPVE - 16-Bit HCS12 MCU 128KB Flash 25MHz | NXP
MC9S12B128MPVE

MC9S12B128MPVE - 16-Bit HCS12 MCU 128KB Flash 25MHz | NXP

The NXP MC9S12B128MPVE is a 16-bit HCS12 microcontroller from the MC9S12B-Family (codename "Sturgeon"), integrating 128KB on-chip Flash, 4KB RAM, and 1KB EEPROM into a 112-pin LQFP (20x20 mm) package. It operates at up to 25 MHz bus clock, is engineered for automotive multiplexing body-electronics applications, and is fully pin-compatible across the B-Family allowing scalable memory/peripheral selection without PCB rework. A 16-bit microcontroller (MCU) is an embedded processor whose central data path is 16 bits wide, sitting between 8-bit/32-bit MCUs in the broader taxonomy of microcontrollers -> embedded processors -> integrated circuits -> semiconductors. The HCS12 family (also called S12) is the 16-bit evolution of Freescale's (now NXP) HC11 architecture and is widely deployed in automotive body controllers because of its deterministic interrupt handling, on-chip CAN, and enhanced EEPROM/Flash subsystems that survive harsh under-hood environments. Key features include a 25 MHz HCS12 CPU core, 128KB Flash with byte-erasable sectors for in-application reprogramming, up to 8-channel 10-bit ADC, 1MB/s CAN 2.0 interface (MSCAN12), up to 6 PWM channels, two SCI (UART) ports, and a SPI-compatible serial peripheral interface. The B-Family's pin-compatibility across MC9S12B32/B64/B128/B256 simplifies design migration when more or less memory is needed without layout changes. Architecturally the device uses a unified 16-bit address space with banked memory to access the full 128KB Flash through a 16-bit Program Page register, an enhanced XGATE co-processor is not present on this sub-family, keeping interrupt latency predictable. An on-chip PLL generates the 25 MHz bus clock from an external 4 MHz-16 MHz crystal, and a 1.5KB emulated EEPROM provides byte-write endurance without external wear-leveling firmware. Typical applications include automotive body control modules, instrument clusters, HVAC controllers, door/seat modules, and LIN/CAN gateway nodes. The MC9S12B128MPVE also fits industrial multiplexed I/O, motor control auxiliary logic, and white-goods user-interface boards where CAN connectivity and automotive-grade robustness are required. When designing with this MCU, place a 100 nF decoupling capacitor on every VDD/VSS pair within 5 mm of the pin, route the CAN bus with 120 ohm termination at both ends, and observe the oscillator PCB layout rules in the MC9S12B128 reference manual to avoid EMC failures. Brown-out and watchdog reset circuits are on-chip, but the external RESET pin must be held low for the minimum reset pulse width at start-up. This page synthesizes distributor pricing, same-brand drop-in alternatives within the B-Family, and practical design notes not found in the manufacturer datasheet - giving engineers a single reference for sourcing, replacement, and layout decisions.

Cotización Contacto
MC9S12B128VFUE - 16-Bit 25MHz HCS12 MCU 128KB Flash | NXP
MC9S12B128VFUE

MC9S12B128VFUE - 16-Bit 25MHz HCS12 MCU 128KB Flash | NXP

The NXP MC9S12B128VFUE is a 16-bit HCS12 CISC microcontroller operating at 25 MHz with 128 KB of on-chip Flash memory and an 80-pin QFP (14x14 mm) footprint. It is a member of the Freescale/NXP S12B family designed for automotive multiplexing and body-electronics applications. An HCS12 microcontroller is a 16-bit CISC (Complex Instruction Set Computer) MCU built around the HCS12 CPU core, falling under the broader category of microcontrollers -> embedded processors -> microprocessors -> semiconductors. The HCS12 architecture extends the earlier HC12 with enhanced instruction set, hardware debug (BDM) support, and richer peripheral integration, while keeping code compatibility with the legacy HC12 instruction set. The S12B sub-family specifically targets cost-sensitive automotive body and chassis applications where moderate Flash density and a rich peripheral mix are needed. Key features of the MC9S12B128VFUE include 128 KB Flash program memory, 4 KB RAM, 1 KB EEPROM, an 8-channel 10-bit ADC, multiple CAN / SCI / SPI / I2C interfaces, and an operating voltage range of 2.5 V to 5 V. The on-chip HCS12 core delivers deterministic interrupt response and integrated background debug mode (BDM), enabling in-circuit programming and real-time development without external emulators. The 80-QFP (PQFP) package supports easy manufacturing with conventional surface-mount processes. The MC9S12B128VFUE implements the HCS12 CISC core with a 16-bit ALU, 16-bit index registers and a unified address space that simplifies C compiler code generation. Its peripheral set is managed by the System Integration Module (SIM), which handles clock generation, interrupt prioritization, chip-select routing and external bus configuration. Internal phase-locked loop (PLL) and on-chip voltage regulator allow flexible oscillator selection while keeping the core on a stable internal rail. Typical applications include automotive body controllers, climate/HVAC modules, instrument clusters, lighting control modules, seat and door-zone modules, and industrial CAN nodes. The integrated CAN 2.0 A/B controller makes it especially well-suited for in-vehicle networks where LIN/CAN gateway functions are required. When designing with the MC9S12B128VFUE, route the BDM signals (BKGD, MODC) to a 6-pin standard debug header to keep development and field-update paths open, and pay close attention to decoupling near each VDD/VSS pair on the 80-QFP package. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design considerations that complement the manufacturer datasheet and help engineers shorten the component-selection cycle.

Cotización Contacto
MC9S12B128VPV - 16-Bit 128KB Flash MCU | NXP
MC9S12B128VPV

MC9S12B128VPV - 16-Bit 128KB Flash MCU | NXP

The NXP Semiconductors MC9S12B128VPV is a 16-bit HCS12 CISC microcontroller with 128 KB of Flash memory, 2.5 V or 5 V operation, and a 112-pin LQFP package. It belongs to the MC9S12B automotive-multiplexing family, whose members are described as fully pin compatible for scalable memory and peripheral options. The device combines embedded Flash program memory with automotive-oriented communication and control capabilities in one integrated circuit. A microcontroller is a programmable semiconductor that executes firmware, reads inputs, controls outputs, and manages embedded-system communication. Within the product hierarchy, the MC9S12B128VPV is a 16-bit MCU, a CISC processor, an embedded Flash controller, and a semiconductor used in electronic control units. Automotive multiplexing designs commonly use multiple microcontrollers connected through communication networks to coordinate distributed vehicle functions while centralizing coordination among body, comfort, and related systems. The verified product information identifies the core as HCS12, the instruction width as 16-bit, the Flash memory as 128 KB, and the supply options as 2.5 V and 5 V. Its 112-pin LQFP package provides a comparatively high pin count suitable for systems requiring numerous I/O resources and dedicated peripheral connections. The verified material does not provide detailed clock, RAM, CAN, timer, ADC, operating-temperature, or automotive-qualification values, so those parameters should be confirmed in the family documentation before schematic capture. MC9S12B-family devices were designed for automotive multiplexing applications, and the family description specifically emphasizes pin compatibility across different memory and peripheral options. That architectural approach supports product scaling: engineers may select a family member according to Flash capacity or peripheral set while retaining package-level design continuity. It does not, by itself, prove that every family member is a drop-in replacement for MC9S12B128VPV. Typical uses include body-control modules, vehicle multiplexing controllers, distributed automotive control units, sensor aggregation nodes, and actuator coordination controllers. In these systems, the MCU reads switches and sensors, executes control logic, manages communication links, and drives outputs. The 128 KB Flash capacity provides room for embedded software, while the 112-pin LQFP package exposes a broad external connection surface. Design work should begin by downloading the MC9S12B family datasheet and confirming the exact VPV pin assignment, peripheral multiplexing, clock requirements, reset connections, programming interface, and decoupling. Because the search data confirms the family and package but does not expose a complete verified pin table, engineers should treat the published family documentation as the controlling source before layout or replacement decisions. This product page consolidates verified source facts, package identity, application context, engineering caveats, and sourcing links. It adds design-oriented interpretation without presenting unverified clock, memory-map, qualification, or lifecycle claims as established specifications.

Cotización Contacto
MC9S12B256CFU - 16-bit 256KB Flash Automotive MCU | NXP
MC9S12B256CFU

MC9S12B256CFU - 16-bit 256KB Flash Automotive MCU | NXP

The NXP MC9S12B256CFU is a 16-bit HCS12 CISC microcontroller with 256KB of flash memory, operation from 2.5V/5V, and a listed maximum speed of 50MHz. It is packaged in an 80-pin PQFP and is identified for automotive multiplexing applications. The verified listing combines the legacy Freescale Semiconductor MC9S12B family identity with current NXP sourcing, so engineers should treat NXP as the supplier brand while recognizing the original family documentation. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. In the product hierarchy, the MC9S12B256CFU is a 16-bit microcontroller, a CISC-based embedded controller, a flash-memory MCU, and a semiconductor. HCS12 devices are intended for embedded control systems where deterministic peripheral access, communication, timing, and automotive-style multiplexing can be useful. The verified data identifies three headline characteristics: 16-bit architecture, 256KB flash, and operation at 2.5V or 5V. One marketplace listing also specifies a 50MHz speed, but that value should be checked against the exact datasheet and clock configuration before relying on it. The family is described as supporting automotive multiplexing applications and offering pin compatibility across different memory and peripheral options for scalable designs. The HCS12 CISC architecture differs from many low-cost 8-bit MCUs by providing a wider internal word and register-oriented control environment. Flash storage permits firmware to be retained in the controller itself, reducing external program-memory requirements. The exact list of timers, serial interfaces, analog modules, CAN functions, interrupt sources, and package-level multiplexing options is not supplied in the verified excerpts and therefore requires confirmation from the manufacturer datasheet. Typical use cases include automotive body and multiplexing controllers, embedded automotive modules, industrial control equipment, and legacy embedded platforms that already depend on HCS12 software tools. A migration should preserve the package footprint, pin multiplexing, clock setup, memory map, interrupt vector table, and development-tool compatibility. Replacing this MCU with a different architecture is not automatically a drop-in substitution even when flash size appears similar. Designers should verify the PQFP pin assignment, power rails, decoupling, external crystal or clock options, reset behavior, programming connector, and exposed peripheral limits against the exact MC9S12B256 datasheet. For production sourcing, confirm NXP lifecycle status, automotive qualification details, errata, and toolchain support. The available LCSC listing reports in-stock status and a starting price, but current commercial availability and lead time should be reconfirmed. This page consolidates the verified 16-bit, 256KB, 2.5V/5V, 50MHz listing data, source links, sourcing questions, and engineering cautions. It does not invent undocumented peripheral specifications or claim a drop-in replacement where verified pin and parameter data is absent.

Cotización Contacto
MC9S12B256MFUE - 16-bit HCS12 MCU, 256KB Flash | NXP
MC9S12B256MFUE

MC9S12B256MFUE - 16-bit HCS12 MCU, 256KB Flash | NXP

The NXP Semiconductors MC9S12B256MFUE is a 16-bit HCS12 microcontroller with 256KB of Flash memory, 25 MHz CPU clock, and an 80-pin QFP package (14x14 mm). It belongs to the S12B family of flash-based MCUs and is fully pin compatible with other members of the family, enabling scalable designs across memory and peripheral configurations. A microcontroller (MCU) is an integrated circuit that combines a CPU core, volatile memory (RAM), non-volatile program memory (Flash/ROM), and a configurable set of peripherals (timers, ADCs, communication interfaces) on a single die. The HCS12 core is a 16-bit CISC architecture from NXP that evolved from the HC11/HC12 lineage, optimized for automotive and industrial real-time control. The S12B family sits within the broader NXP 16-bit MCU hierarchy: HCS12 core -> S12B sub-family -> MC9S12B series -> specific MPNs with different memory/peripheral mixes. Key features of the MC9S12B256MFUE include: 256KB Flash (256K x 8) with Fast Page Erase, 12KB RAM, 4KB EEPROM, a 10-bit ADC, an 8-channel PWM module, plus multiple communication interfaces including CAN 2.0 (msCAN), SCI, SPI, and I2C. The on-chip Enhanced Capture Timer (ECT) provides six 16-bit channels for input capture and output compare, supporting precise event timing required for engine and chassis control. The device operates from 2.35V to 5.5V supply, supports -40C to +125C junction temperature, and integrates a PLL-based clock generator for flexible bus-speed scaling. The BDM (Background Debug Mode) interface and on-chip single-wire debug simplify in-circuit programming and field firmware updates. Internal architecture pairs the HCS12 CPU with a 32-bit HCS12X-style peripheral bus for higher throughput on time-critical registers. Typical applications include automotive body and chassis modules, CAN-connected sensor nodes, industrial PLCs, HVAC controllers, and LIN/CAN bridges. Engineered for automotive multiplexing, the S12B family allows designers to swap memory or peripheral options without PCB rework, reducing time-to-market for tier-1 OEMs and aftermarket modules. When designing with this MCU, place decoupling capacitors within 5 mm of each VDD/VSS pair, route the resonator/oscillator traces with a guarded ground channel, and keep CAN-H/CAN-L differential pairs at 100 ohm impedance. The NRND designation means NXP has flagged the part for limited future support - designers of new programs should evaluate S12XE or S12Z successors at the architectural level. This page synthesizes distributor inventory, drop-in alternatives drawn from the same S12B and S12XE pin-compatible families, and practical design notes beyond what is in the standalone datasheet.

Cotización Contacto
MC9S12B256MPVE - 16-Bit 25MHz 256KB Flash MCU | NXP
MC9S12B256MPVE

MC9S12B256MPVE - 16-Bit 25MHz 256KB Flash MCU | NXP

The NXP Semiconductors MC9S12B256MPVE is a 16-bit HCS12 microcontroller operating at 25 MHz, with 256 KB of flash memory and a 112-LQFP package measuring 20 mm by 20 mm. It belongs to the MC9S12B family of flash-based microcontrollers created for automotive multiplexing and other embedded control applications. Verified source data also describes the family as providing fully pin-compatible options for scalable designs. A microcontroller is a programmable integrated circuit that executes firmware, reads sensor inputs, controls actuators, and coordinates communication with other electronics. In the broader semiconductor hierarchy, this device is a 16-bit MCU within the embedded-processing category. Its HCS12 architecture combines flash-backed program storage with integrated peripherals, making it suitable for control-oriented systems that need deterministic embedded logic rather than a general-purpose desktop processor. The three most prominent verified specifications are the 16-bit CPU architecture, 25 MHz operating frequency, and 256 KB flash capacity. Additional details such as RAM capacity, supply voltage, peripheral inventory, temperature range, timers, communication interfaces, and electrical limits are not exposed in the supplied verified records. Those values must be taken from the manufacturer datasheet rather than inferred from the family name or distributor category text. The MC9S12B family is associated with automotive multiplexing applications, where one electronic module may exchange data with several other modules while also performing local control. Its flash-based design allows firmware to be programmed and revised without removing the device from its circuit. The verified DigiKey record identifies the part specifically as a 16-bit, 25 MHz MCU with 256 KB flash in a 112-LQFP package. Typical design contexts include body and vehicle multiplexing modules, distributed control units, sensor-interface controllers, actuator controllers, industrial communication equipment, and compact embedded platforms that need a 16-bit MCU. For automotive or industrial use, the complete datasheet must confirm electrical limits, automotive qualification, environmental ratings, transceiver behavior, and any timing constraints before the design is released. The LQFP footprint requires careful escape routing and thermal-aware PCB layout. Because the complete verified dataset does not expose exact pin assignments, pin multiplexing rules, clock requirements, decoupling values, or absolute maximum ratings, engineers should use the official MC9S12B256 documentation and preserve its reference-layout recommendations. The supplied Octopart page offers a route to the latest available datasheet and aggregated technical information. This page consolidates verified distributor specifications, sourcing links, application context, and explicit data gaps. It intentionally does not invent memory values, voltage ranges, pin names, timing limits, or lifecycle claims that are absent from the supplied records. Availability and pricing also require confirmation at order time because the provided results contain no numeric price or current stock figure.

Cotización Contacto
MC9S12B64CFUE - 16-Bit HCS12 MCU 64KB Flash 25MHz 80-QFP | NXP
MC9S12B64CFUE

MC9S12B64CFUE - 16-Bit HCS12 MCU 64KB Flash 25MHz 80-QFP | NXP

The NXP MC9S12B64CFUE is a 16-bit HCS12 microcontroller built around the S12 CPU core, featuring 64 KB of on-chip Flash memory, a 25 MHz maximum bus clock, and an 80-pin QFP (14x14 mm) package. It targets automotive multiplexing and body-electronics applications where the MC9S12B family provides pin-compatible memory scaling across the product line. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and peripherals such as timers, ADCs, and communication interfaces. Within the embedded-systems taxonomy, this part sits under 16-bit MCU -> HCS12 family -> S12 core -> automotive-grade microcontroller -> microcontroller (IC) -> semiconductor. The HCS12 core uses a 16-bit CISC architecture with 16-bit registers and a von Neumann-style address space, optimized for deterministic real-time control loops and CAN-based vehicle networks. Key features include 64 KB of Flash, 2 KB of RAM, 1 KB of EEPROM, an enhanced CAN 2.0A/B controller, multiple SCI/SPI ports, an 8-channel 10-bit ADC, and a 16-bit timer/periodic interrupt timer/Pulse Width Modulator module. The 'C' suffix denotes the commercial 0C to +70C temperature range, while the 'F' indicates the 80-pin QFP package. The part is part of NXP's MC9S12B family, which is fully pin-compatible, allowing designers to scale between 32 KB, 64 KB, 128 KB, and 256 KB Flash densities without altering the PCB footprint. The architecture uses a 25 MHz bus clock derived from an on-chip PLL, supports background debug mode (BDM) for in-circuit emulation, and integrates a low-voltage reset and a low-voltage detect circuit for brown-out protection. Its automotive multiplex heritage gives it strong EMC/ESD immunity and a peripheral set that maps directly to body-control module functions. Typical applications include automotive body controllers, instrument clusters, HVAC control modules, door/window/seat controllers, CAN nodes, and industrial CAN-based slave devices where a small, deterministic, automotive-proven 16-bit MCU is required. When designing with this part, place the 0.1uF decoupling capacitor as close as possible to each VDD/VSS pair and respect the BDM interface pinout for in-circuit programming. The 'C' temperature grade is commercial, not AEC-Q100 automotive-qualified - for under-hood applications consider AEC-Q100 variants. This page synthesizes distributor pricing, drop-in alternatives from the MC9S12B family, and practical design notes not consolidated in the manufacturer datasheet.

Cotización Contacto
MC9S12B64MFUE - 16-Bit 25MHz HCS12 MCU 64KB Flash | NXP
MC9S12B64MFUE

MC9S12B64MFUE - 16-Bit 25MHz HCS12 MCU 64KB Flash | NXP

The NXP MC9S12B64MFUE is a 16-bit microcontroller from the HCS12 family, featuring a 25 MHz CPU core with 64 KB of embedded Flash memory and packaged in an 80-pin QFP (14x14 mm). Based on NXP's HCS12 CISC architecture, the part integrates 2 KB of RAM, multiple communication peripherals, and a 5V-tolerant I/O set, targeting cost-sensitive automotive and industrial body/comfort applications. Background: an HCS12 microcontroller is a member of the 16-bit HCS12 family of MCUs from NXP Semiconductors, designed to deliver automotive-grade compute performance with rich peripheral integration while retaining code compatibility with the legacy HC11 family. The HCS12 sits in the broader taxonomy of microcontrollers -> standard 16-bit MCUs -> automotive microcontrollers. Compared with 8-bit controllers it offers higher throughput and richer peripherals; compared with 32-bit Cortex-M parts it remains attractive where deterministic timing at moderate clock rates, on-chip EEPROM-like endurance, and legacy code bases matter. Key features include a 25 MHz core bus clock, 64 KB of Flash program memory, 2 KB of RAM, on-chip timers, an SPI module, two SCI (UART) modules, and a CAN 2.0 controller. The part supports background debug mode (BDM) for non-intrusive in-circuit debug and is qualified for extended temperature operation typical of automotive environments. The MC9S12B64MFUE uses an enhanced HCS12 CPU with BDM/Single-Wire Debug support, interrupt stacking, and integrated memory protection. Peripherals are mapped via a standardized S12 memory map and driven through the standard Freescale/NXP peripheral library, simplifying firmware portability across S12 family variants. Typical applications include automotive body controllers (mirror, seat, door modules), HVAC controllers, instrument cluster I/O expanders, and industrial sensor interface nodes. Designers select this part where legacy S12 firmware needs to be reused or where automotive-grade reliability of the established HCS12 platform is required. A practical design tip: when migrating from the legacy MC68HC912B32 family, retain oscillator and reset circuit topologies, since the MC9S12B64MFUE maintains pin-compatible register layouts for BDM and SCI, reducing firmware rework. Plan current budget on each 5V supply rail - the part draws more current at 25 MHz than at the 8 MHz that some legacy designs used. This page synthesizes distributor pricing across DigiKey, Mouser and Octopart, identifies same-package drop-in alternates from the S12 family, and provides design notes beyond what the manufacturer datasheet alone captures - including thermal, BDM and supply-rail guidance specific to the 80-QFP variant.

Cotización Contacto
MC9S12B64MPVE - 16-Bit 25MHz 64KB MCU | NXP
MC9S12B64MPVE

MC9S12B64MPVE - 16-Bit 25MHz 64KB MCU | NXP

The NXP Semiconductors MC9S12B64MPVE is a 16-bit HCS12 microcontroller with an S12 core, 25 MHz operation, 64 KB of flash memory, and a 112-pin LQFP package measuring 20 mm by 20 mm. It is positioned for automotive and industrial embedded-control designs that require deterministic control processing and broad peripheral integration. The supplied distributor records conflict on maximum frequency, identifying the device as both 25 MHz and 50 MHz; the NXP product page and technical summaries identify 25 MHz, while the higher figure is retained only as a reported distributor discrepancy. A microcontroller is a semiconductor device that executes firmware, reads inputs, controls outputs, and coordinates peripherals within an embedded system. The HCS12 MC9S12B64 belongs to the broader hierarchy of 16-bit MCU, embedded processor, embedded-control IC, and semiconductor. Its flash-based architecture supports standalone control applications without an external program-memory device, while the large 112-pin package exposes substantially more I/O and peripheral connections than a small 32-pin or 48-pin MCU. Verified features include a 16-bit S12 core, 64 KB organized as 64K by 8 bits of flash, and a -40 °C to +125 °C operating-temperature range. The package is identified as 112-pin LQFP in a 20 mm by 20 mm body. One aggregation source identifies the device as CMOS, with a 260 °C peak reflow temperature, 40-second maximum peak-reflow exposure, MSL 3, and tin terminal finish. These process attributes matter when selecting assembly process and handling components after opening moisture-sensitive packaging. Typical uses include automotive body, multiplexing, sensor, actuator, and communication-control modules. The broad temperature range supports harsh industrial environments, while the 64 KB flash capacity accommodates embedded control firmware and application data. Exact RAM capacity, peripheral inventory, supply voltage, ADC performance, timer resources, communication modules, and individual pin functions were not supplied in the verified dataset and therefore must be confirmed from the manufacturer datasheet before schematic capture. Designers should use the 112-pin package only when the required I/O and peripheral mix justifies its footprint. Confirm every pin, alternate function, power pin, ground pin, decoupling requirement, and programming interface against the official documentation. For a new PCB, also evaluate smaller active HCS12 devices that may meet the actual memory and I/O needs; for an existing MC9S12B64 design, lifecycle and sourcing constraints should be addressed explicitly. This page consolidates the supplied manufacturer and distributor records, separates conflicting frequency claims, identifies sourcing and lifecycle concerns, and provides engineering-focused selection guidance. Detailed pricing, complete pinout, and verified drop-in replacement MPNs were not available, so this synthesis avoids presenting unsupported values as production-ready design data.

Cotización Contacto
MC9S12C128MFAE - 16-bit HCS12 MCU, 128KB Flash, 48-LQFP | NXP
MC9S12C128MFAE

MC9S12C128MFAE - 16-bit HCS12 MCU, 128KB Flash, 48-LQFP | NXP

The NXP MC9S12C128MFAE is a 16-bit HCS12 microcontroller featuring 128KB of on-chip Flash memory and a maximum CPU clock of 25MHz, housed in a 48-pin LQFP package (7x7 mm). It is part of NXP's S12C family of 48/52/80-pin flash-based MCUs targeting cost- and space-sensitive general-purpose industrial and automotive network applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and a rich set of peripherals such as timers, ADC, communication interfaces, and I/O ports. The MC9S12C128MFAE belongs to the broader category of embedded microcontrollers within integrated circuits (ICs), and more specifically to the 16-bit CISC microcontroller sub-family based on the CPU12 instruction set architecture. Its on-chip bandgap-based voltage regulator accepts a wide 2.97V to 5.5V external supply range and generates the internal digital supply voltage (VDD). Key features include 128KB of Flash program memory (128K x 8), 4KB of RAM, an integrated PLL for clock generation, multiple 16-bit timer channels, a 10-bit ADC, and standard serial interfaces including SCI, SPI, and IIC. The 25MHz bus speed is derived from an internal phase-locked loop referenced to an external crystal or resonator. The device also integrates a background debug module (BDM) for non-intrusive in-circuit programming and debugging, which is critical for production-grade automotive firmware development. The MC9S12C128MFAE is fabricated on a mature 0.25 micron Flash process and uses the CPU12 core, which is binary-compatible with the HC12 instruction set and offers an enhanced indexed addressing mode. Single-wire background debug mode (BDM), on-chip voltage regulator, and integrated oscillator simplify PCB design by reducing external component count. The device supports both stop and pseudo-stop low-power modes for energy-constrained applications. Typical applications include automotive body and chassis networks (CAN/LIN nodes), industrial control (PLC I/O modules, motor drive peripheral control), appliance control (white goods HMI), sensor interfacing, and general 16-bit embedded systems. Its wide 2.97V-5.5V supply tolerance and robust peripheral set make it well-suited for noisy industrial environments. According to the manufacturer product page, this part is currently marked NRND (Not Recommended for New Designs). When designing with this device, ensure adequate decoupling with 100nF ceramic capacitors placed close to each supply pin. Use the BDM interface for firmware updates, and place the external filter capacitor for the internal voltage regulator (VREG) as recommended in the manufacturer datasheet. The 48-LQFP footprint is a standard outline shared across the S12C family, simplifying PCB reuse for derivative designs with different memory sizes or peripheral mixes. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. All data is verified against distributor listings and cross-referenced with the NXP product information page.

Cotización Contacto
MC9S12C128MFUE - 16-bit HCS12 MCU, 128KB Flash, 25MHz | NXP
MC9S12C128MFUE

MC9S12C128MFUE - 16-bit HCS12 MCU, 128KB Flash, 25MHz | NXP

The NXP Semiconductors MC9S12C128MFUE is a 16-bit HCS12 microcontroller with 128KB Flash, 4KB RAM, and a 25MHz CPU core, housed in an 80-pin LQFP (14x14) package. It is part of the S12C family of flash-based microcontrollers designed for cost- and space-sensitive industrial and automotive network applications, integrating the 16-bit CPU12 core with on-chip peripherals. What is a microcontroller (MCU)? A microcontroller is a single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), working memory (RAM), and programmable peripherals (timers, ADC, communication controllers, GPIO) onto one die. HCS12 microcontrollers belong to the broader category of embedded microcontrollers, which themselves sit within the embedded systems domain of semiconductors. The 16-bit HCS12 (CPU12) core offers higher code density and richer peripherals than 8-bit cores (8051, AVR) while remaining simpler than 32-bit ARM Cortex-M devices, making it a sweet spot for body controllers, sensor nodes, and gateway modules. Key features include 128KB on-chip Flash, 4KB RAM, an integrated bandgap-based voltage regulator (Vreg) that derives the internal 2.5V digital supply from a 2.97V to 5.5V external rail, a phase-locked loop (PLL) for flexible bus-clock generation, and a CAN 2.0 controller for automotive network connectivity. The device also offers a 10-bit ADC, PWM channels, SCI/SPI/I2C serial interfaces, and 31 general-purpose I/O lines. A built-in background debug mode (BDM) supports in-circuit programming and non-intrusive debug without an expensive emulator. The S12C architecture employs a von-Neumann memory map with Flash wait-state insertion for the 25MHz core, EEPROM emulation via a Flash partitioning scheme, and a peripheral memory protection unit. The internal regulator eliminates the need for an external 2.5V LDO on most designs, and the wide 2.97V to 5.5V supply range allows direct connection to automotive 5V rails. Typical applications include automotive body controllers, instrument clusters, HVAC control modules, industrial sensor interfaces, CAN nodes, and LIN masters in body-electronics networks. Designers also use the S12C family in motor control appliances and low-end industrial gateways. The 80-pin LQFP footprint simplifies two-layer PCB layouts and hand-rework prototyping. A key design consideration: confirm that the bus clock (E-clock) and peripheral bus speeds meet timing for the highest-priority interrupt service routine. Decoupling the VDDR/VSS pins with 1uF ceramic caps near the package is recommended because the internal regulator drives significant switching current at full bus speed. This page consolidates distributor stock, parametric cross-references, drop-in alternatives, and engineering design notes not found in the manufacturer datasheet, providing information gain over DigiKey or Mouser listings.

Cotización Contacto
MC9S12C128MPBE - 16-Bit 25MHz HCS12 MCU, 128KB Flash | NXP
MC9S12C128MPBE

MC9S12C128MPBE - 16-Bit 25MHz HCS12 MCU, 128KB Flash | NXP

The NXP Semiconductors MC9S12C128MPBE is a 16-bit HCS12 microcontroller with 128KB of on-chip Flash and a 25MHz CPU12 core, housed in a 52-pin LQFP (10x10 mm) package. It is part of the S12C family, which delivers the 16-bit HCS12 core in a cost- and space-optimized footprint aimed at cost-sensitive general-purpose industrial and automotive network applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and a set of peripherals such as timers, ADCs, communication controllers, and GPIO. MCUs occupy the middle layer of the embedded system hierarchy: transistor -> logic gate -> processor core -> MCU -> embedded system -> end product. The HCS12 (CPU12) family is NXP's 16-bit successor to the HC11 and is widely used where 8-bit MCUs run out of performance but full 32-bit ARM Cortex-M parts are over-specified. Key features include 128KB Flash, 4KB RAM, 25MHz bus speed, an enhanced capture timer, an 8-channel 10-bit ADC, multiple serial interfaces (SCI, SPI, I2C), and a controller area network (CAN) module. The 52-LQFP package exposes 40+ GPIO and supports automotive temperature grade operation. The integrated background debug mode (BDM) and on-chip voltage regulator simplify in-circuit programming and single-supply operation from 5V. Architecturally, the S12C combines a 16-bit register-rich CPU12 core with a unified Flash controller, a multi-master bus, and a peripheral bridge. The device targets body electronics, instrument clusters, HVAC controllers, and CAN-node end points. Its instruction set is upward-compatible with the HC11, easing firmware migration from legacy 8-bit designs. Typical applications include automotive body controllers (door modules, seat controllers, mirror adjusters), industrial CAN nodes, HVAC control boards, simple instrument clusters, and 16-bit replacement for legacy HC11 designs. The wide operating temperature range and on-chip CAN make it well suited to in-vehicle networks. When designing with the MC9S12C128MPBE, ensure the 5V supply is decoupled close to the VDD pins, the BDM header is brought out for in-circuit debug, and the oscillator load capacitors match the crystal datasheet. Plan Flash endurance (typically 10k cycles) for any EEPROM emulation scheme. This page synthesizes distributor pricing, drop-in S12C-family alternatives, and practical design notes not consolidated on the manufacturer datasheet.

Cotización Contacto
MC9S12C128VFAE - 16-Bit HCS12 MCU, 128KB Flash, 25MHz, 48-LQFP | NXP
MC9S12C128VFAE

MC9S12C128VFAE - 16-Bit HCS12 MCU, 128KB Flash, 25MHz, 48-LQFP | NXP

The NXP MC9S12C128VFAE is a 16-bit HCS12 CISC microcontroller featuring 128KB (128K x 8) of embedded Flash program memory, 4KB of RAM, and 31 general-purpose I/O lines, housed in a 48-pin LQFP (7x7 mm) package. It operates from a 2.5V/5V supply, runs at up to 25MHz bus speed, and integrates an internal oscillator, making it well suited for cost- and space-sensitive industrial and automotive network applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. The HCS12 family is a 16-bit CISC architecture introduced by Motorola and continued by Freescale (now NXP) that delivers higher code density than typical 8-bit cores while retaining the deterministic interrupt behavior expected in embedded control. Within NXP's portfolio the HCS12C sub-family targets general-purpose applications where the rich peripheral set and 16-bit data paths deliver more headroom than legacy HC08/HCS08 designs without the cost of higher-tier DSP or Power-Architecture parts. Key features of the MC9S12C128VFAE include 128KB of on-chip Flash, an HCS12 CPU core with background debug mode (BDM), an internal oscillator eliminating the need for an external crystal in many designs, and a peripheral set covering CAN, SCI (UART), SPI, PWM, a watchdog timer, and power-on reset. The device supports both 2.5V and 5V operation, easing migration from 5V HC11/HC12 designs and supporting modern 3.3V peripheral rails. The 48-LQFP (7x7 mm) package exposes 31 I/O and the full address/data bus for external memory expansion when needed. Architecturally the HCS12C integrates the CPU12 core, a System Integration Module (SIM) for clock, reset, and interrupt control, a 128KB Flash module, 4KB RAM, and analog/digital peripherals onto a single die. Bus speed of 25MHz provides approximately 8-10 MIPS of effective throughput at the 16-bit datapath, which is ample for sensor interfacing, simple protocol stacks, and small RTOS workloads. Typical applications include industrial CAN nodes, automotive body and chassis ECUs, sensor signal conditioning, low-cost motor control, metering, HVAC controllers, and general-purpose 16-bit embedded platforms. The integrated CAN controller is particularly valuable in-vehicle and factory-floor networks. Engineers also use this part as a pin-compatible upgrade path from older HC12 Flash parts when more program memory is required. When designing with this part, confirm that your BDM/debug toolchain supports the HCS12 family and that the chosen C compiler has a matching startup file for the C128 derivative. Decoupling must follow NXP's reference design - one 100nF per VDD pin plus a 4.7uF bulk capacitor - and unused I/O should be configured as outputs or pulled to a defined state to minimize Icc. This page synthesizes distributor stock, real-time pricing, drop-in same-family alternatives, and practical HCS12 design notes - information that goes beyond the manufacturer datasheet alone.

Cotización Contacto
MC9S12C32CFUE25 - 16-bit 25MHz HCS12 MCU, 32KB Flash | NXP
MC9S12C32CFUE25

MC9S12C32CFUE25 - 16-bit 25MHz HCS12 MCU, 32KB Flash | NXP

The NXP MC9S12C32CFUE25 is a 16-bit HCS12 microcontroller running at 25 MHz with 32 KB of on-chip Flash and 2 KB RAM, housed in an 80-pin PQFP (QFP-80) package. Part of NXP's S12C family of flash-based MCUs, it combines the CPU12 core's deterministic performance with a rich peripheral set, including a 10-bit ADC, PWM, SCI/SPI, CAN (msCAN) interface, and on-chip bandgap voltage regulator supporting 2.97V to 5.5V external supply. An HCS12 microcontroller is a 16-bit automotive-grade MCU based on the CPU12 core, designed for cost- and space-sensitive general-purpose industrial and automotive network applications. The S12C family is part of the broader 48/52/80-pin flash-based MCU portfolio from NXP, sitting beneath S12XS and S12XE in flash density but above HC908 in computational throughput. Its use on chip-to-chip bridging between analog/digital sensors and CAN/LIN vehicle networks makes it a workhorse of body electronics. Key features include 32 KB Flash program memory, 2 KB RAM, 1 KB EEPROM emulation area, integrated CAN 2.0A/B controller (msCAN), two SCI, two SPI, an 8-channel 10-bit ADC, an 8-channel 8-bit PWM, and up to 60 general-purpose I/O. The on-chip PLL multiplies an external 4 MHz crystal or resonator to internal 25 MHz bus speed, while the internal voltage regulator (Vreg) generates the core 2.5V from the 3V-5.5V external supply. Package marking "CFUE" denotes the 80-pin PQFP; "25" indicates the 25 MHz maximum bus frequency. Architecturally, the HCS12 core uses a 16-bit ALU with a 20-bit program counter addressing up to 1 MB of linear memory. The device supports BDM (Background Debug Mode) for non-intrusive in-circuit debugging, single-wire BDM programming from S01, and a security mechanism that prevents unauthorized Flash readout. The wide 3V-5.5V supply range and 0.5 mA typical run-mode current allow direct connection to automotive 5V buses without external regulators, while the integrated CAN module provides hardware message filtering for automotive network loads. Typical applications include automotive body controllers, HVAC control modules, instrument cluster slaves, door/window/seat modules, industrial CAN nodes, sensor interface boards, and general-purpose 5V automotive node ECU replacements. Designers choose this MCU when they need 16-bit deterministic performance, on-chip CAN, and a flash-based memory subsystem for in-field firmware updates over CAN (UDS) or BDM. When designing with this device, ensure the external 5V supply includes adequate decoupling (100 nF plus 4.7 uF bulk within 10 mm of each VDD/VSS pair). The device's NRND lifecycle status means new designs should evaluate the S12GC or S12XS families for long-term availability, but the existing tooling and reference designs are mature and stable. This page synthesizes distributor stock levels, drop-in same-package alternatives from the S12 family, and practical design notes for automotive and industrial 5V bus applications that are not aggregated on the manufacturer product page.

Cotización Contacto
MC9S12C32CPBE25 - HCS12 16-bit MCU 32KB Flash 25MHz | NXP
MC9S12C32CPBE25

MC9S12C32CPBE25 - HCS12 16-bit MCU 32KB Flash 25MHz | NXP

The NXP MC9S12C32CPBE25 is a 16-bit HCS12 CISC microcontroller with 32KB of on-chip Flash, 2KB of RAM, and 25 MHz CPU clock, housed in a 52-pin LQFP (10x10 mm) package. It belongs to NXP's S12C "Goldfish" family of flash-based microcontrollers that deliver 16-bit performance for general-purpose industrial and automotive network applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), timers, communication peripherals, and I/O ports on one silicon die. Within the broader taxonomy, MCUs belong to embedded processors, which sit alongside microprocessors, DSPs, and SoCs in the semiconductor hierarchy. The HCS12 core is a 16-bit CISC architecture originally derived from the Motorola HC12, widely deployed in automotive body electronics and industrial control. Key features of the MC9S12C32CPBE25 include 32KB (32K x 8) of Flash program memory, an integrated bandgap-based on-chip voltage regulator (Vreg) accepting 2.97 V to 5.5 V external supply, a Phase-Lock-Loop (PLL) circuit for flexible bus-speed configuration, multiple timers including a 16-bit Pulse-Width Modulation (PWM) module, an 8-channel 10-bit Analog-to-Digital Converter (ADC), CAN (Controller Area Network) and SCI/SPI serial interfaces, and up to 60 general-purpose I/O pins depending on package variant. The 16-bit HCS12 core delivers high code density for embedded C applications while maintaining low power consumption suitable for always-on industrial nodes. The S12C architecture uses a pipelined CISC core with enhanced indexed addressing modes, BDM (Background Debug Mode) for in-circuit debug, and a flash-friendly memory map. The internal Vreg derives the core logic supply VDD from a single external rail, simplifying PCB design. A non-maskable interrupt (XIRQ) and 7 maskable interrupt sources support real-time control tasks typical of body controllers and sensor interfaces. Typical applications include automotive body controllers (BCM), HVAC control modules, instrument cluster sub-MCUs, industrial sensor interface nodes, CAN/J1850 network nodes, seat and door zone controllers, and low-end powertrain peripherals that do not require a 32-bit MCU. The wide 2.97 V to 5.5 V supply range tolerates automotive load-dump conditions and 5 V industrial backplanes. When designing with this part, leave headroom in the LQFP-52 thermal envelope and ensure the Vreg decoupling network (4.7 uF + 0.1 uF) follows the S12C reference design. Note the NRND lifecycle status - production is winding down, so design in the Q1 automotive qualified variant or migrate to the S12G family for new designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page or in the raw datasheet excerpts.

Cotización Contacto
MC9S12C32MFAE16 - HCS12 16-Bit MCU 32KB Flash LQFP-48 | NXP
MC9S12C32MFAE16

MC9S12C32MFAE16 - HCS12 16-Bit MCU 32KB Flash LQFP-48 | NXP

The NXP Semiconductors MC9S12C32MFAE16 is a 16-bit HCS12 CISC microcontroller integrating 32KB of on-chip Flash memory and operating at a 16 MHz bus clock, housed in a 48-pin LQFP package. It targets cost-sensitive industrial and automotive network applications, providing on-chip peripherals, an integrated bandgap voltage regulator (VREG), and an on-chip PLL for flexible system clocking from a 2.97 V to 5.5 V external supply. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, and integrated peripherals such as timers, communication interfaces (SCI/SPI/I2C), and analog-to-digital converters. The HCS12C belongs to the broader HCS12 family of 16-bit CISC microcontrollers, optimized for deterministic real-time control in body electronics, sensor interfacing, and LIN-connected automotive nodes. Within the embedded hierarchy, MCUs sit below microprocessors (MPUs) and above standard logic ICs, providing an autonomous compute engine with on-chip non-volatile storage for firmware. Key differentiating features of the MC9S12C32MFAE16 include 32KB Flash, 2KB RAM, 1KB EEPROM, an 8-channel 10-bit ADC, up to 38 general-purpose I/O lines, an enhanced capture/timer module, and background debug mode (BDM) for in-circuit programming and debug. The integrated on-chip bandgap voltage regulator and phase-locked loop simplify power and clock tree design, removing the need for external regulators or oscillator tuning networks. Architecturally, the HCS12 core uses a 16-bit data path with a memory-management unit that unifies Flash, RAM, and EEPROM into a linear 64KB address space, supporting C and assembly firmware development through NXP's CodeWarrior and the GCC-based Eclipse toolchains. The peripheral module library is fully documented in NXP reference manuals, allowing deterministic interrupt-driven design with 16-bit timer prescalers and pulse-width modulation for motor and lighting loads. Typical applications include automotive body controllers, HVAC actuators, instrument clusters, and LIN/CAN-connected sensor nodes, as well as industrial general-purpose control where its 16-bit performance and 32KB flash capacity meet firmware size budgets. The 48-pin LQFP footprint makes it suitable for through-hole-compatible hand-rework prototypes and high-volume surface-mount assembly. Designers should allocate the VDD/VSS pins per the package pinout to ensure stable supply for the on-chip voltage regulator, place decoupling capacitors close to all VDD pins, and route the oscillator traces symmetrically when using an external crystal. The BDM interface requires a dedicated debug header for in-circuit programming; this must be considered in the PCB layout to avoid post-layout rework. This page synthesizes distributor stock, lifecycle status, drop-in alternatives, and design notes not found on a single manufacturer or distributor page, enabling engineers to evaluate the MC9S12C32MFAE16 for new designs and legacy migration.

Cotización Contacto