Microcontroladores

Productos (18737)

PIC24FV08KM202-I/SO - 16-bit XLP MCU, 8KB Flash, 28-SOIC | Microchip
PIC24FV08KM202-I/SO

PIC24FV08KM202-I/SO - 16-bit XLP MCU, 8KB Flash, 28-SOIC | Microchip

The Microchip Technology PIC24FV08KM202-I/SO is a 16-bit PIC® XLP™ 24F family microcontroller that delivers 32 MHz CPU performance with 8 KB Flash and 2 KB SRAM in a 28-pin SOIC (SO) wide-body package. It belongs to the FV variant, supporting a wide 2.0V to 5.5V operating range that enables both 3.3V and 5V systems from a single part, while the PIC24F (non-V) siblings cover 1.8V-3.6V. The MCU integrates eXtreme Low Power (XLP) technology, a 12-bit ADC, dual 8-bit DACs, operational amplifiers, comparators, and a Configurable Logic Cell (CLC). A microcontroller (MCU) is a single-chip computer that contains a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and a rich set of peripherals such as ADC, timers, communication ports, and I/O pins. The PIC24F family uses a 16-bit modified Harvard RISC architecture with 16-bit wide instructions and 24-bit wide data paths, sitting in the hierarchy (in-band interconnect) PIC24F -> PIC24 -> PIC -> 8-bit microcontroller -> embedded processor -> semiconductor. The XLP designation denotes nanoWatt technology for sleep currents below 100 nA in deep sleep modes. Key specifications include 32 MHz MIPS performance, 8 KB Flash (2.75K x 24 instruction words), 2 KB SRAM, integrated 12-bit ADC up to 500 ksps, two 8-bit DACs, three op-amps, two analog comparators, three 16-bit Capture/Compare/PWM (CCP) modules, two UART, one SPI, one I²C, and a 25 mA source/sink per I/O capability. The Configurable Logic Cell allows hardware-level combinational and sequential logic without burning CPU cycles, useful for glue-logic replacement and event-driven signaling. Typical applications include portable medical devices (blood glucose meters, pulse oximeters), battery-powered IoT sensor nodes, low-power LCD or segment displays, consumer remote controls, smart thermostats, and industrial 4-20 mA loop-powered transmitters. The wide operating voltage makes it compatible with both 3.3V digital ICs and legacy 5V analog front-ends. When designing with this MCU, choose a supervisor/MCU pair that matches your real-time response needs; the 32 MHz core delivers 16 MIPS. For lowest sleep current, route unused pins as outputs and disable unused peripherals via PMD registers. The 28-SOIC package supports easy hand-soldering and breadboard prototyping.

Cotización Contacto
PIC24FV08KM202-I/SS - 16-bit XLP MCU, 8KB Flash, 32MHz | Microchip
PIC24FV08KM202-I/SS

PIC24FV08KM202-I/SS - 16-bit XLP MCU, 8KB Flash, 32MHz | Microchip

The Microchip Technology PIC24FV08KM202-I/SS is a 16-bit PIC24F microcontroller from the XLP (eXtreme Low Power) family, integrating 8KB of Flash program memory, 2KB of SRAM, and 512B of EEPROM into a 28-pin SSOP package. It operates from 2.0V to 5.5V (the FV variant supports 5V) and runs the CPU at up to 32MHz instruction rate, delivering roughly 16 MIPS throughput. The part number suffix /SS denotes the 28-lead SSOP package, while /I denotes the industrial temperature range of -40C to +85C. A PIC (Peripheral Interface Controller) microcontroller is a Harvard-architecture RISC processor designed by Microchip, sitting within the broader MCU > microcontroller > embedded processor > semiconductor hierarchy. The 16-bit PIC24F family targets low-power, analog-rich embedded designs and is widely used in consumer, industrial, and IoT products where deterministic behavior, integrated peripherals, and low sleep current matter more than raw MHz. Key features include a 12-bit A/D converter with up to 16 channels, two 8-bit DACs, two operational amplifiers, two analog comparators, three op-amp/comparator/timer modules, and Microchip's Configurable Logic Cell (CLC) for hardware-level glue logic without external gates. Communication peripherals cover I2C, SPI, UART, and CCP/CCP capture/compare/PWM modules for motor and lighting control. The 'FV' prefix specifically guarantees 5V-tolerant operation alongside 3.3V systems, enabling designs that mix legacy 5V analog with modern 3.3V logic. Typical applications include low-power sensor nodes, e-metering, battery-powered medical devices, LED lighting controllers, HVAC control panels, and small appliance human-machine interfaces. The XLP sleep currents in the nanoamp range extend battery life for products that wake infrequently and need years of standby operation. When designing with this part, reserve at least two GPIO for SWD-style programming/debug if you plan to use ICSP, and verify the FV voltage tolerance if your rails exceed 3.6V. The internal 7.37MHz FRC oscillator with PLL gives you a free 32MHz system clock without any external crystal, saving BOM cost in cost-sensitive designs. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the bare manufacturer datasheet, so engineers can shortlist candidates faster.

Cotización Contacto
PIC24FV08KM202T-I/ML - 16-Bit 32MHz 8KB FLASH MCU | Microchip
PIC24FV08KM202T-I/ML

PIC24FV08KM202T-I/ML - 16-Bit 32MHz 8KB FLASH MCU | Microchip

The Microchip Technology PIC24FV08KM202T-I/ML is a 16-bit PIC® XLP™ 24F microcontroller (MCU) featuring 8 KB of FLASH program memory, 2 KB of RAM, and a maximum CPU speed of 32 MHz. It is housed in a 28-pin QFN (ML, 6x6 mm) package with an exposed thermal pad, making it one of the most integrated analog-plus-digital low-pin-count devices in the PIC24F family. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (FLASH/ROM), data memory (RAM), and a rich set of on-chip peripherals such as timers, communication interfaces, ADCs, and DACs. The PIC24F family sits in the 16-bit MCU segment of Microchip's portfolio, above the 8-bit PIC16/PIC18 lines and below the 32-bit PIC32 line. The "XLP" (eXtreme Low Power) designation indicates the device targets battery-powered and energy-harvesting applications with sub-uA sleep currents. PIC24F devices generally operate from 1.8 V to 5.5 V (the FV variant retains 5 V tolerance and adds a wider flash endurance window), making them well-suited to coin-cell, 2xAA, and 3.3 V/5 V mixed-rail systems. Key differentiating specifications of this part include integrated 12-bit ADC, an 8-bit DAC, on-chip operational amplifiers, and a Configurable Logic Cell (CLC) - features rarely bundled at this pin count. Communication peripherals include I2C, SPI, UART/USART, LIN, and IrDA. The 32 MHz CPU delivers up to 16 MIPS, sufficient for real-time control loops, sensor fusion, and basic signal processing. Architecturally, the PIC24FV08KM202 uses a 16-bit modified Harvard core with a 24-bit instruction word, allowing single-cycle MAC operations and deterministic interrupt latency. The wide 1.8-5.5 V supply range, eXtreme Low Power modes (sleep, deep sleep, RTCC), and integrated analog make this device well suited for portable instrumentation, sensor hubs, and consumer electronics. Typical applications include low-power IoT sensor nodes, battery-powered medical devices (glucose meters, pulse oximeters), LIN slave nodes in automotive body electronics, e-metering and smart thermostats, and small industrial HMI panels. The integrated op-amp + DAC chain enables direct photodiode or bridge-sensor interfaces without external analog ICs. When designing with this part, pay attention to the 28-QFN PCB footprint and exposed pad layout - the e-pad must be soldered to a sufficient ground copper area (typically >= 1 square inch) to meet the datasheet's thermal resistance spec. Decoupling capacitors should be placed within 3 mm of the VDD/VSS pins. This page synthesizes distributor pricing, parametric data, drop-in alternatives from the PIC24F KM family, and practical PCB design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC24FV08KM202T-I/SO - 16-bit 32MHz 8KB Flash XLP MCU | Microchip
PIC24FV08KM202T-I/SO

PIC24FV08KM202T-I/SO - 16-bit 32MHz 8KB Flash XLP MCU | Microchip

The Microchip Technology PIC24FV08KM202T-I/SO is a 16-bit PIC microcontroller from the PIC XLP 24F family operating at up to 32 MHz with 8 KB of Flash program memory (organized as 2.75K x 24 instructions), 2 KB of RAM, and integrated analog peripherals including 12-bit ADC, 8-bit DAC, operational amplifiers, comparators and a Configurable Logic Cell (CLC). The -I/ suffix denotes the -40C to +85C industrial temperature range, the T indicates Tape and Reel packaging, and /SO marks the 28-pin SOIC (0.295 inch / 7.50 mm body width) package. A 16-bit PIC microcontroller (MCU) is a microcontroller built around a 16-bit modified Harvard architecture core with separate program and data buses, 16 working registers, and a single-cycle hardware multiply. PIC24F parts sit between the 8-bit PIC16/PIC18 families and the 32-bit PIC32MX line, providing more performance and peripherals than 8-bit parts while retaining the simple MPLAB X IDE / XC16 toolchain and the Peripheral Pin Select (PPS) flexibility that 8-bit PICs lack. The XLP (eXtreme Low Power) designation indicates deep-sleep currents in the nanoamp range, multiple idle/sleep modes, and dynamic clock gating for battery-powered applications. In the broader taxonomy, PIC24FV08KM202 belongs to: microcontroller -> embedded MCU -> semiconductor IC -> PIC24F family. The most differentiating specifications of the PIC24FV08KM202 are its wide operating voltage range of 2.0V to 5.5V (the FV variant; the F variant operates at 1.8V-3.6V), eXtreme Low Power technology with down to nanoamp sleep currents, and a high level of analog integration in a small 28-pin SOIC footprint - features uncommon in low-pin-count PIC parts. The integrated op amps and 8-bit DAC allow direct sensor signal conditioning on-chip without external analog ICs. Technically, the part uses Microchip's nanoWatt XLP technology with multiple low-power modes (Sleep, Idle, Doze, Alternate Run modes), a 12-bit ADC with up to 12 input channels, up to three op amps configurable as amplifiers or comparators, a 5-bit or 10-bit DAC, multiple Capture/Compare/PWM (CCP/ECCP) modules, a Configurable Logic Cell for glue-logic replacement, and a peripheral pin select (PPS) system that remaps digital peripherals to most I/O pins. Typical applications for the PIC24FV08KM202T-I/SO include ultra-low-power IoT sensor nodes, portable medical monitoring devices, battery-powered instrumentation with on-chip signal conditioning, and consumer products needing 5V-tolerant I/O. The wide 2.0V-5.5V range also makes it suitable for both 3V coin-cell and 5V USB-powered designs without a separate regulator. When designing with this MCU, ensure MPLAB X IDE with the XC16 compiler is used for firmware development; Microchip's Code Configurator (MCC) plugin accelerates peripheral setup. PPS remapping must be configured before peripheral use, and decoupling should follow standard 100 nF + bulk capacitor placement within 5 mm of the VDD pins. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the PIC24F family, and practical design notes not consolidated on the manufacturer product page.

Cotización Contacto
PIC24FV08KM202T-I/SS - 16-bit 8KB Flash XLP MCU, 28-SSOP | Microchip
PIC24FV08KM202T-I/SS

PIC24FV08KM202T-I/SS - 16-bit 8KB Flash XLP MCU, 28-SSOP | Microchip

The Microchip Technology PIC24FV08KM202T-I/SS is a 16-bit PIC24F XLP (eXtreme Low Power) microcontroller with 8KB Flash, 2KB RAM, 512B EEPROM, 12-bit ADC, 8-bit DAC, integrated op amps, and configurable logic cell, in a 28-pin SSOP package. It operates from 2.0V to 5.5V at up to 32MHz. A PIC microcontroller (MCU) is a programmable embedded processor that integrates a CPU, non-volatile Flash memory, RAM, peripherals, and I/O on a single silicon die. The PIC24F family uses a 16-bit modified Harvard architecture with DSP-enhanced instructions, bridging 8-bit PIC16/PIC18 designs and 32-bit PIC32MX designs. Within the PIC taxonomy, PIC24F belongs to the eXtreme Low Power (XLP) tier that targets battery-powered applications: deep sleep currents in the nanoamp range and active currents in the microamp-per-MHz range. Key differentiating features of this part include: integrated 12-bit ADC with up to 500 ksps sampling rate, dual 8-bit DAC outputs with waveform generation, two operational amplifiers with internal/external configuration, a Configurable Logic Cell (CLC) for hardware glue logic, multiple Capture/Compare/PWM (CCP) and output compare modules, plus 5-bit and 16-bit timers. The FV (wide-voltage) prefix denotes support down to 2.0V, versus the standard F variant at 1.8V/2.0V minimums in this family. Communication peripherals include I2C, SPI, UART with IrDA and LIN host support. Typical applications include portable medical sensor nodes, eMetering data concentrators, low-power wireless sensor interfaces (with attached radio), LED lighting controllers, and small appliance user interfaces. The integrated op amps and DACs reduce BOM cost in mixed-signal analog front-end designs where external amplifiers would otherwise be required. When designing with this MCU, evaluate sleep current at your application's idle duty cycle: XLP modes below 100 nA are achievable but require correct peripheral gating. The SSOP-28 package offers easier hand-soldering than QFN options at the cost of slightly larger PCB footprint. Confirm debugger compatibility (ICD 3, PICkit 4, MPLAB Snap) and required programming voltage for your production flow. This page consolidates distributor pricing, drop-in same-package alternatives, and application notes drawn from the Microchip datasheet family - content not bundled in the standalone datasheet PDF.

Cotización Contacto
PIC24FV08KM204-E/MV - 16-bit XLP MCU, 8KB Flash, 32MHz | Microchip
PIC24FV08KM204-E/MV

PIC24FV08KM204-E/MV - 16-bit XLP MCU, 8KB Flash, 32MHz | Microchip

The Microchip Technology PIC24FV08KM204-E/MV is a 16-bit PIC® XLP™ 24F microcontroller featuring 8KB (2.75K x 24) of Flash program memory, 2KB of RAM, and a 32MHz maximum CPU speed, housed in a 48-pin UQFN (MV) package measuring 6x6 mm. Designed for eXtreme Low Power (XLP) operation, the device integrates an enhanced 16-bit modified Harvard architecture with a wide operating voltage range suited for both battery-powered and line-powered embedded designs. What is a 16-bit microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of peripherals such as ADCs, timers, communication interfaces, and I/O. A 16-bit MCU like the PIC24FV family occupies the middle ground between 8-bit MCUs (lowest cost, lowest performance) and 32-bit MCUs (highest performance, highest cost), offering enough compute headroom for sensor fusion, motor control, and signal processing without the power and code-size overhead of a Cortex-M class device. PIC24F devices specifically target low-power portable applications through Microchip's XLP technology, which minimizes active and sleep currents so that coin-cell and energy-harvesting designs remain viable. The PIC24FV08KM204 integrates 22 channels of 10-bit/12-bit ADC, dual 8-bit DACs, configurable logic cells, op-amps, multiple Capture/Compare/PWM (CCP) modules, and communication peripherals. XLP features deliver nanoWatt sleep currents, allowing the device to wake on interrupts for asynchronous sampling. Typical applications include handheld medical devices, IoT sensor nodes, low-energy wireless platforms, USB/LED lighting controllers, and consumer electronics. Designers choose this MCU when balancing code density, peripheral integration, and sub-microamp standby current in compact PCB footprints. Designers must respect the MV (UQFN-48 6x6 mm) land pattern, ensure exposed-pad soldering for thermal dissipation, and select the appropriate -E (extended) or -I (industrial) temperature grade per their end environment. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet.

Cotización Contacto
PIC24FV08KM204-I/PT - 16-bit XLP MCU, 8KB Flash, 44-TQFP | Microchip
PIC24FV08KM204-I/PT

PIC24FV08KM204-I/PT - 16-bit XLP MCU, 8KB Flash, 44-TQFP | Microchip

The Microchip Technology PIC24FV08KM204-I/PT is a 16-bit PIC® XLP™ 24F microcontroller with 8 KB (2.75K x 24) of Flash program memory and 2 KB of RAM, operating at up to 32 MHz, housed in a 44-pin TQFP (10x10 mm) package. The "FV" prefix indicates the wide-voltage 2V-5.5V tolerant core, and the "I/PT" suffix denotes the industrial temperature range (-40C to +85C) in TQFP packaging. A 16-bit microcontroller (MCU) is an integrated circuit combining a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals on a single die. The PIC24F family sits in Microchip's eXtreme Low Power (XLP) tier, optimized for battery-powered and energy-harvesting designs where nanoWatt sleep currents and fast wake-up times are decisive. Within the broader taxonomy, PIC24F MCUs belong to the 16-bit microcontroller class, which bridges 8-bit PIC microcontrollers and 32-bit ARM Cortex-M devices. Key features of the PIC24FV08KM204 include an integrated 12-bit ADC with up to 22 input channels, two 8-bit DACs, operational amplifiers on-chip, configurable logic cells (CLC), multiple Capture/Compare/PWM modules, and the XLP nanoWatt sleep modes with currents in the microamp range. The 32 MHz MIPS core provides up to 16 MIPS throughput while consuming as little as 250 uA/MHz active, and the wide 2V-5.5V supply range supports direct Li-ion, 3.3V and 5V rails. The architecture combines a 16-bit modified Harvard RISC core with a hardware multiply/divide, a 17-bit x 17-bit single-cycle multiplier, and zero-overhead loop control. Analog-rich integration (12-bit ADC, 8-bit DACs, op amps) eliminates many external components, while CLC peripheral logic lets designers implement combinatorial logic in firmware, reducing BOM and PCB area. Typical applications include portable medical sensors, IoT edge nodes, low-power wireless sensor hubs, battery-powered instrumentation, and consumer devices such as wearables and remote controls. The integrated analog peripherals make the device especially well suited to sensor conditioning and signal measurement. When designing with this part, choose a low-ESR ceramic bypass capacitor (100 nF) on VDD and AVdd, keep analog traces short, and use the deep-sleep modes with RTCC for sub-microamp standby. Migrating to the 16-KB Flash sister part PIC24FV16KM204 is footprint-compatible for code-growth headroom.

Cotización Contacto
PIC24FV08KM204T-I/ML - 16-bit XLP MCU, 8KB Flash, 44-QFN | Microchip
PIC24FV08KM204T-I/ML

PIC24FV08KM204T-I/ML - 16-bit XLP MCU, 8KB Flash, 44-QFN | Microchip

The Microchip PIC24FV08KM204T-I/ML is a 16-bit PIC® XLP™ 24F microcontroller delivering 32 MIPS performance at 32 MHz, 8 KB of self-programmable Flash program memory, 2 KB of SRAM, and integrated analog peripherals in a 44-pin QFN (8x8 mm) package with exposed thermal pad. The 'FV' family variant supports a wide 2.0 V to 5.5 V operating range, making it ideal for battery-powered designs that must also interface with 5 V analog systems. A PIC24F microcontroller is a 16-bit modified Harvard RISC core from Microchip's PIC24F family, positioned between 8-bit PIC16/PIC18 parts and 32-bit PIC32 devices. Within the broader taxonomy: PIC24F -> 16-bit microcontroller -> microcontroller (MCU) -> embedded controller -> semiconductor. XLP (eXtreme Low Power) parts add nanoWatt technology peripherals such as deep sleep, RTC, and ultra-low-power watchdog, allowing the chip to extend battery life in always-on applications. Key features include an integrated 12-bit A/D converter with up to 16 input channels, dual 8-bit DACs, three operational amplifiers, three analog comparators, a configurable logic cell (CLC), and multiple PWM/SCCP/MCCP timers. Communication peripherals include UART, SPI, I²C, and IrDA support. The 44-QFN exposed-pad package provides low thermal resistance and a compact 8x8 mm footprint suitable for dense PCB designs. Typical applications include portable medical instruments, USB human-interface devices, sensor hubs, low-power wireless sensor nodes, and e-metering front ends. The wide 2.0–5.5 V supply range also suits industrial 24 V bus pre-regulation post-buck stages. For best noise performance, place 0.1 µF ceramic decoupling capacitors adjacent to every VDD/VSS pair and connect the QFN exposed pad to a solid ground plane. Designers migrating from older PIC24F parts should review the Configurable Logic Cell configuration - misconfigured CLC blocks are a common first-prototype failure mode.

Cotización Contacto
PIC24FV08KM204T-I/MV - 16-Bit 32MHz XLP MCU 8KB Flash | Microchip
PIC24FV08KM204T-I/MV

PIC24FV08KM204T-I/MV - 16-Bit 32MHz XLP MCU 8KB Flash | Microchip

The Microchip PIC24FV08KM204T-I/MV is a 16-bit PIC24F microcontroller with 8KB Flash, 2KB RAM, and a maximum CPU speed of 32MHz, housed in a 48-pin UQFN (6x6 mm) package with exposed pad. It operates across 2.5V/3.3V/5V rails and integrates a 10/12-bit ADC, dual 8-bit DACs, op-amps, and a configurable logic cell (CLC) for hardware customization. A microcontroller (MCU) is an integrated circuit combining a CPU, memory (Flash for program code, SRAM for data), and a rich set of peripherals on a single silicon die. The PIC24F family sits in the 16-bit MCU segment of Microchip's product tree, above 8-bit PIC MCUs and below 32-bit SAM/PIC32 devices. The 'V' in PIC24FV denotes the wide-voltage variant that supports 2.0V-5.5V operation, ideal for battery-powered designs where supply varies as cells discharge. Key features include 8KB (2.75K x 24 words) Flash program memory, 2KB SRAM, an integrated 22-channel 10/12-bit ADC supporting 100 ksps at 12-bit resolution, dual 8-bit Digital-to-Analog converters, operational amplifiers, comparators, and a Configurable Logic Cell (CLC). The 'XLP' (eXtreme Low Power) designation delivers sub-uA sleep currents, making it suited to energy-harvesting and long-life battery applications. The device uses a 16-bit modified-Harvard RISC architecture with a 32MHz internal oscillator. It includes 21-channel touch-sensing support, hardware crypto engine (CEC-compatible variants), and 5V-tolerant I/O. The 48-pin UQFN exposed-pad package improves thermal dissipation and PCB real-estate efficiency for space-constrained wearables and IoT nodes. Typical applications include portable medical sensor interfaces, IoT sensor hubs, e-metering, consumer wearables, touch-button user interfaces, and battery-powered industrial sensor nodes. Designers select this part for designs needing analog integration (ADC+DAC+op-amp) without external components. Designers should note that the 'T' suffix denotes tape-and-reel packaging for high-volume assembly, and the 'I' grade specifies -40C to +85C industrial temperature range. The 'V' variant's wide-voltage tolerance reduces power supply complexity for multi-cell battery designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet - unique value for engineers selecting this PIC24F MCU.

Cotización Contacto
PIC24FV08KM204T-I/PT - 16-Bit 32MHz 8KB Flash MCU | Microchip
PIC24FV08KM204T-I/PT

PIC24FV08KM204T-I/PT - 16-Bit 32MHz 8KB Flash MCU | Microchip

The Microchip PIC24FV08KM204T-I/PT is a 16-bit PIC microcontroller from the PIC XLP 24F family, operating at up to 32 MHz with 8 KB Flash program memory (2.75K x 24 organization) and 2 KB SRAM. It is supplied in a 44-pin TQFP (10x10 mm) package, designated by the PT suffix and qualified to the -40C to +85C industrial temperature range. The 'FV' prefix indicates a wide-voltage VDD range suitable for both 3.3V and 5V-tolerant system designs. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory, data memory and a rich set of peripherals into a single chip, forming the computational heart of every embedded system. The PIC24F is Microchip's 16-bit modified Harvard family, sitting above the 8-bit PIC10/12/16 architectures and below the 32-bit PIC32MX/dsPIC families, with class-leading code density, deterministic interrupts and the MPLAB X ecosystem for firmware development. The 'XLP' (eXtreme Low Power) label targets battery-powered designs with nanoWatt sleep currents in the nanoamp range. Key features of the PIC24FV08KM204T-I/PT include integrated analog peripherals (multiple DACs, operational amplifiers and comparators), a Configurable Logic Cell (CLC) for hardware glue logic, 5V-tolerant digital I/O, and CIP-rated on-chip peripherals for safety-critical applications. The device is supported by the MPLAB XC16 compiler and the MPLAB X IDE toolchain. Typical applications include portable medical devices, e-metering, energy harvesting nodes, sensor signal conditioning, industrial control, automotive body and infotainment subsystems, LED lighting control, USB device/host bridges, and consumer appliances where the wide VDD tolerance simplifies mixed-voltage designs. When designing with this device, follow Microchip's recommended decoupling (100 nF on each VDD pin plus a bulk 10 uF) and use the ICSP pins (PGECx/PGEDx) for in-circuit programming - do not float the MCLR pin. Verify absolute maximum VDD against your brown-out configuration. This page synthesizes real-time distributor pricing, Microchip drop-in variants, parametric comparison, and practical design notes not aggregated in the manufacturer datasheet or in single distributor listings.

Cotización Contacto
PIC24FV16KA301-E/P - 16KB Flash XLP 16-bit MCU | Microchip
PIC24FV16KA301-E/P

PIC24FV16KA301-E/P - 16KB Flash XLP 16-bit MCU | Microchip

The Microchip PIC24FV16KA301-E/P is a 16-bit PIC microcontroller featuring eXtreme Low Power (XLP) technology, 16KB Flash program memory (5.5K x 24), 2KB RAM, and 512B EEPROM in a 20-pin PDIP through-hole package. It operates up to 32MHz delivering 16 MIPS performance, with a wide operating voltage range from 2.0V to 5.5V, suitable for both 3.3V and 5V systems. A 16-bit microcontroller (MCU) is a programmable integrated circuit that uses a 16-bit data path and instruction word, sitting between 8-bit MCUs (lower cost, simpler peripherals) and 32-bit MCUs (higher performance, larger address space). The PIC24F family specifically targets ultra-low-power applications, with XLP technology enabling nanoWatt deep-sleep modes. PIC24F MCUs are widely used in battery-powered, energy-harvesting, and always-on sensor applications where both computational throughput and quiescent current matter. Key features of the PIC24FV16KA301 include integrated peripherals such as a 12-bit ADC (up to 16 channels), a Charge Time Measurement Unit (CTMU) for capacitive touch sensing, multiple UART/SPI/I²C interfaces, and unique deep-sleep peripherals including DSBOR (Deep Sleep Brown-Out Reset), DSWDT (Deep Sleep Watchdog Timer), and RTCC (Real-Time Clock Calendar) that continue to run while the CPU is asleep. The 'FV' variant indicates a wide-voltage (2.0V-5.5V) part versus the 'F' standard-voltage (1.8V-3.6V) variant. The device uses a 16-bit modified Harvard RISC architecture with single-cycle instruction execution and hardware multiply support. Internal oscillator options eliminate the need for external crystals in many designs, reducing BOM cost. The 20-pin PDIP package provides breadboard-friendly through-hole mounting suited to prototyping, education, and legacy industrial designs. Typical applications include battery-powered sensor nodes, wearable health monitors, remote controls, low-power wireless sensor networks, capacitive touch user interfaces, and industrial metering. The integrated CTMU simplifies touch-button and slider implementation without external timing circuits. When designing with this part, leverage the deep-sleep modes aggressively: DSBOR, DSWDT, and RTCC retain functionality below 1µA. Use the internal FRC oscillator for active mode to minimize current draw, and switch peripherals off individually when not in use to maximize battery life. This page synthesizes verified distributor pricing, pin-compatible alternatives, and practical design notes to help engineers select and apply the PIC24FV16KA301-E/P efficiently.

Cotización Contacto
PIC24FV16KA301-E/SO - 16KB Flash 16-bit MCU, 32MHz XLP | Microchip
PIC24FV16KA301-E/SO

PIC24FV16KA301-E/SO - 16KB Flash 16-bit MCU, 32MHz XLP | Microchip

The Microchip Technology PIC24FV16KA301-E/SO is a 16-bit Flash microcontroller from the PIC24F XLP (eXtreme Low Power) family, featuring 16KB (5.5K x 24) of Flash program memory, 2KB RAM, and 512B EEPROM, packaged in a 20-pin SOIC (SO) wide-body 300-mil surface-mount package. It operates at 32MHz / 16 MIPS across a 3.3V-5V wide VDD range and ships with the -E (Extended) temperature grade of -40C to +125C, making it well-suited for industrial and harsh-environment designs. The 'FV' prefix in the part number indicates the wide-voltage (1.8V-5.5V) process variant, while the non-FV 'F' variant is 3V-only. A 16-bit microcontroller is an embedded processor that uses a 16-bit data path and instruction word to balance code density, deterministic interrupt latency, and computational throughput for control-oriented tasks. PIC24F parts sit in Microchip's mid-range 16-bit portfolio above the 8-bit PIC16/PIC18 lines and below the dsPIC33/dsPIC35 DSP-capable parts. PIC24F is purpose-tuned for low-power and mixed-signal applications rather than DSP math, and the XLP sub-family adds nanoWatt technology with sub-uA deep-sleep current to compete with MSP430 and STM32L0 in battery-powered end equipment. Key features of the PIC24FV16KA301-E/SO include a 12-bit ADC, CTMU (Charge Time Measurement Unit) for capacitive touch and mTouch sensing, 16 MIPS performance at 32MHz, deep-sleep-aware peripherals such as DSBOR (Deep-Sleep Brown-Out Reset), DSWDT (Deep-Sleep Watchdog Timer), and RTCC (Real-Time Clock Calendar), plus a Peripheral Pin Select (PPS) subsystem for flexible pin mapping. The device integrates a 16-bit timer, 3-wire SPI, I2C, UART, and a 5-channel hardware comparator, enabling direct connection of analog and digital sensors without external glue logic. Architecturally, the PIC24FV16KA301 uses Microchip's modified Harvard RISC core with a 16-bit instruction word and 24-bit instruction address space, allowing linear code memory up to 16M instructions and supporting C-compiled firmware with the MPLAB XC16 toolchain. Hardware-level support is provided for low-power modes including Sleep, Deep Sleep, and Retention modes, with wake sources from RTCC, external interrupts, and DSWDT. PPS and the unified analog front-end mean the same silicon can be reused across product variants simply by changing firmware, which simplifies inventory for OEMs. Typical applications include battery-powered IoT sensor nodes, e-metering and utility metering, capacitive touch user interfaces, medical handheld devices, low-power industrial sensors, and consumer appliances. The wide 1.8V to 5.5V VDD range lets the same part run from a single Li-ion cell, two AAs, or a regulated 3.3V rail, eliminating the need for separate hardware variants for different power domains. When designing with this device, prioritize CTMU calibration on first power-up and size the decoupling network to at least 100nF + 10uF bulk per VDD/AVDD pair. A 32.768kHz crystal is recommended for RTCC accuracy; without it, deep-sleep RTC drift can exceed 5% and break long-interval timer applications. This page consolidates distributor pricing, drop-in alternatives, and engineering design notes that supplement the manufacturer datasheet, supporting faster sourcing and design decisions for engineers evaluating PIC24F XLP devices.

Cotización Contacto
PIC24FV16KA301-E/SS - 16-bit XLP MCU 16KB Flash | Microchip
PIC24FV16KA301-E/SS

PIC24FV16KA301-E/SS - 16-bit XLP MCU 16KB Flash | Microchip

The Microchip Technology PIC24FV16KA301-E/SS is a 16-bit Flash microcontroller built on the PIC24F eXtreme Low Power (XLP) architecture, delivering up to 32 MIPS at 3.3 V in a 20-pin SSOP package. It integrates 16 KB of program Flash, 2 KB of SRAM, and 512 B of EEPROM, together with a 12-bit A/D converter, a Real-Time Clock/Calendar (RTCC), and a Charge Time Measurement Unit (CTMU) for capacitive touch sensing. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and a rich set of peripherals onto one die. The PIC24F family sits within the broader 16-bit PIC architecture, which scales up to the dsPIC digital signal controllers. The XLP variants add Deep Sleep operating modes with sub-µA currents, targeting battery-powered and energy-harvesting applications where quiescent draw dominates battery life. The "FV" prefix in the part number denotes the wide-voltage silicon revision (2.5 V/3.3 V/5 V tolerant I/O and core). Key features of the PIC24FV16KA301 include 16 MIPS performance per MHz, hardware multipliers, a 16-bit timer/counter bank, multiple UART/SPI/I2C serial interfaces, and the CTMU peripheral that allows calibrated µA-range current measurements for thermistors or capacitive buttons. The Deep Sleep mode retains RTCC, DSBOR (Deep Sleep Brown-Out Reset), DSWDT (Deep Sleep Watchdog Timer), and a small register file at currents typically under 1 µA, which is critical for applications that spend most of their life in standby. Typical applications include portable medical sensors, smart thermostats, battery-powered IoT nodes, capacitive touch user interfaces, and remote controls. In each case, the combination of wide-voltage operation, RTCC retention, and CTMU-based sensing reduces external component count and extends battery service life. When designing with this MCU, verify Vdd decoupling per Microchip's application note recommendations and confirm that the active supply current at the chosen MIPS rate fits within the power budget. For designs that require more code space, step up to the PIC24FV32KA301 within the same SSOP-20 footprint; for designs that need more pins, move to the 28- or 44-pin variants in the family.

Cotización Contacto
PIC24FV16KA301-I/P - 16KB Flash, 16 MIPS XLP MCU | Microchip
PIC24FV16KA301-I/P

PIC24FV16KA301-I/P - 16KB Flash, 16 MIPS XLP MCU | Microchip

The Microchip Technology PIC24FV16KA301-I/P is a 16-bit Flash microcontroller from the PIC24FV KA family featuring eXtreme Low Power (XLP) technology, 16 KB program Flash, 2 KB RAM, and 512 B EEPROM, housed in a 20-pin PDIP (0.300 inch, 7.62 mm) through-hole package. It executes up to 16 MIPS at 32 MHz, integrates a 12-bit ADC, CTMU (Charge Time Measurement Unit), 17 general-purpose I/O pins, and supports wide operating voltage from 2.0V to 5.5V (5V tolerant). The -I temperature suffix indicates the -40°C to +85°C industrial operating range, and the FV variant denotes the 5V-tolerant wide-voltage part. An MCU (microcontroller) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM, EEPROM), and peripherals such as ADC, timers, and communication interfaces. The PIC24F family sits in the hierarchy 8-bit PIC -> 16-bit PIC24F -> 32-bit PIC32, balancing 8-bit PIC simplicity with 16-bit MIPS performance. Within that hierarchy, the PIC24FV16KA301 belongs to the XLP sub-family optimized for ultra-low-power battery applications where active current, sleep current, and Deep Sleep mode retention matter as much as raw MIPS. Key features include Deep Sleep mode with RTCC, DSBOR (Deep Sleep Brown-Out Reset), and DSWDT (Deep Sleep Watchdog Timer) for unattended battery operation; 5V-tolerant I/O enabling direct interfacing with 5V legacy peripherals; a 12-bit ADC with up to 16 channels and CTMU supporting capacitive touch and time measurement; and three 16-bit timers plus a Real-Time Clock and Calendar (RTCC). The 16 MIPS throughput delivers ample headroom for sensor fusion, digital control loops, and user-interface firmware in the same device. Architecturally, the PIC24FV16KA301 uses a modified Harvard architecture with a 16-bit data path, 24-bit instruction word, and hardware Multiply/Divide unit. The integrated voltage regulator supports a wide 2.0V to 5.5V supply, with on-chip FRC (Fast RC) and LPRC (Low-Power RC) oscillators eliminating external crystals in cost-sensitive designs. The result is a deterministic, low-power, 16-bit MCU family suited for human-interface, sensor, and IoT endpoint designs. Typical applications include battery-powered IoT sensor nodes, wearable health monitors, remote controls, energy harvesting endpoints, capacitive-touch user interfaces, and low-power industrial sensor transmitters. The 5V-tolerance also suits industrial 24V bus I/O nodes with a 5V regulator downstream. When designing with this device, leverage the XLP peripherals (DSBOR, DSWDT, RTCC) to keep average current in Deep Sleep below 1 µA, allowing 10+ year battery life on a coin cell. Always de-couple VDD/VSS with a 0.1 µF ceramic capacitor placed within 5 mm of the pins. This page synthesizes distributor pricing, drop-in 20-pin PDIP alternatives, and practical XLP design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC24FV16KA301-I/SS - 16-Bit XLP MCU 16KB Flash 32MHz | Microchip
PIC24FV16KA301-I/SS

PIC24FV16KA301-I/SS - 16-Bit XLP MCU 16KB Flash 32MHz | Microchip

The Microchip Technology PIC24FV16KA301-I/SS is a 16-bit XLP (eXtreme Low Power) flash microcontroller delivering 16 MIPS at 32 MHz, with 16KB (5.5K x 24) self-programmable flash, 2KB SRAM, and 512B EEPROM, housed in a 20-pin SSOP package. A microcontroller (MCU) is a single-chip computer integrating a CPU core, program memory, data memory, and peripherals on one die. The PIC24F family sits in the 16-bit microcontroller hierarchy above 8-bit PIC MCUs and below 32-bit ARM-based devices, targeting embedded control applications where power budget and peripheral integration matter more than raw processing throughput. Key features include Microchip's XLP technology with Deep Sleep mode running dedicated DSBOR, DSWDT, and RTCC peripherals for industry-leading nanoamp-level standby power, an on-chip 12-bit ADC with up to 12 channels plus the Charge Time Measurement Unit (CTMU) for capacitive touch and precision measurement, and a wide 2.5V to 5V supply range that tolerates a 5V industrial bus directly. Architecturally, the PIC24F core executes C-efficient 16-bit instructions from a modified Harvard bus with flash organized as 5.5K x 24-bit words. Code-Guard security partitions flash for bootloader protection, and the 17 I/O lines map rich peripherals including two UARTs, SPI, I2C, output compare, input capture, and a real-time clock calendar. Typical applications include battery-powered sensor nodes, capacitive touch user interfaces, industrial sensor front-ends using the CTMU, and low-power data loggers where the RTCC must run for years on a coin cell. For design, exploit the 2.5V-5.5V supply range to eliminate LDOs in 5V systems, and budget sleep currents against DSWDT period for battery-life estimates. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC24FV16KA302-E/ML - 16KB Flash 16-bit XLP MCU | Microchip
PIC24FV16KA302-E/ML

PIC24FV16KA302-E/ML - 16KB Flash 16-bit XLP MCU | Microchip

The Microchip Technology PIC24FV16KA302-E/ML is a 16-bit PIC24F microcontroller from the XLP (eXtreme Low Power) family, featuring 16 KB Flash program memory, 2 KB SRAM, and 512 B EEPROM in a 28-pin QFN (6x6 mm) package with 23 digital I/O pins. A PIC24F microcontroller is a 16-bit Harvard-architecture MCU built around the PIC24 instruction set, which combines deterministic interrupt response, DSP-oriented instructions, and on-chip peripherals such as 12-bit ADC, comparators, RTCC, UART/SPI/I2C, and USB-capable derivatives. PIC24F devices sit between 8-bit PIC16/PIC18 parts and 32-bit PIC32 parts, targeting applications that need higher computational throughput than 8-bit cores but very low active and sleep currents. The 'FV' prefix designates the wide-Vdd 1.8-5.5 V variant, while 'XLP' denotes Microchip's nanoWatt technology, including Deep Sleep with retention RTCC, DSBOR and DSWDT that keep supervising peripherals running while the core is halted. Key features include 32 MHz / 16 MIPS operation from an internal oscillator, 12-bit ADC with CTMU support, multiple serial interfaces (I2C, SPI, UART, IrDA, LIN), 5 V tolerant I/O, and ultra-low deep-sleep currents in the nanoamp range. The device also integrates a hardware RTCC, configurable timer modules, and dual 3-pin analog comparators that remain functional during deep sleep. Typical applications include battery-powered IoT sensor nodes, portable medical monitors, e-paper / wearable displays, energy-harvesting nodes, automotive LIN slaves, and remote controls where quiescent current in the sub-microamp range is critical. The 28-QFN footprint also suits space-constrained designs. When designing with this part, plan the unused I/O strategy early, since 23 of the 28 pins are bonded out. For lowest deep-sleep current, disable unused peripherals, switch the system clock to LPRC, and configure RTCC-alarm wake-up rather than periodic WDT wake-up. The '-E' suffix denotes the -40C to +125C extended temperature grade, suitable for industrial and automotive underhood environments.

Cotización Contacto
PIC24FV16KA302-E/SO - 16KB Flash XLP 16-bit MCU | Microchip
PIC24FV16KA302-E/SO

PIC24FV16KA302-E/SO - 16KB Flash XLP 16-bit MCU | Microchip

The Microchip Technology PIC24FV16KA302-E/SO is a 16-bit RISC Flash microcontroller from the PIC24F XLP (eXtreme Low Power) family, housed in a 28-pin SOIC (SO) wide-body package. It features 16KB of Flash program memory (5.5K x 24 instruction words), 2KB of SRAM, and 512 bytes of EEPROM data memory, and runs the PIC24 CPU core at up to 32MHz delivering 16 MIPS. The 'FV' wide-voltage variant supports 2.5V, 3.3V and 5V operation, making it ideal for mixed-rail designs powered from single-cell Li-ion or USB rails up to industrial 5V buses. Integrated peripherals include a 12-bit ADC, Capture/Compare/PWM (CCP/ECCP), UART, SPI, I2C, and the unique CTMU (Charge Time Measurement Unit) for capacitive touch and precise time measurement. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, and peripherals into one IC. The PIC24F family is Microchip's 16-bit general-purpose MCU tier, sitting between the 8-bit PIC16/PIC18 and the 32-bit PIC32 families. Within that tier, the XLP sub-family is optimized for ultra-low-power applications, with multiple Deep Sleep modes that retain core state while drawing only nanoamps of current. The 'FV' device class extends the supply range from the standard 1.8-3.6V (F) up to 5.5V (FV), removing the need for an external LDO in 5V designs. Key features include Deep Sleep current in the nanowatt range, retention of RTCC (Real-Time Clock/Calendar), DSBOR (Deep Sleep Brown-Out Reset), and DSWDT (Deep Sleep Watchdog Timer) across Deep Sleep, and the CTMU peripheral that converts a timer input into a capacitance measurement - enabling touch buttons, liquid-level sensing, and time-of-flight metrology without an external analog front end. The 12-bit ADC with up to 16 channels, 200 ksps conversion rate, and selectable reference supports sensor signal conditioning directly on-chip. The device is fabricated on an advanced CMOS process and uses a 16-bit modified Harvard architecture with separate program and data buses. Code executes linearly from Flash; interrupt latency is deterministic. The integrated PLL allows the 32MHz core to be derived from the internal 8MHz oscillator or an external crystal, with Fail-Safe Clock Monitor (FSCM) that detects primary-clock failure and switches to the internal LPRC oscillator without application intervention. Typical applications include battery-powered sensor nodes, IoT edge devices, wearables, portable medical monitors, smart remote controls, and any low-power 5V industrial controller. The CTMU peripheral makes it particularly attractive for capacitive touch user interfaces and flow meters. The wide-voltage capability (2.0-5.5V) supports direct Li-ion coin-cell operation and eliminates the BOM cost of a separate voltage regulator in 5V designs. When designing with the PIC24FV16KA302, place a 100 nF decoupling capacitor as close as possible to VDD/VSS pairs and consider a 10 uF bulk capacitor on the main rail. Enable Deep Sleep aggressively between events to maximize battery life; the XLP Wake-on-Touch and RTCC-alarm features keep average current in the nanowatt region for duty-cycled applications. This page synthesizes distributor pricing, drop-in package alternatives, application notes, and design considerations that are not found in any single manufacturer datasheet, giving engineers a single reference for sourcing, second-sourcing, and implementing this MCU.

Cotización Contacto
PIC24FV16KA302-I/ML - 16-bit 32MHz XLP MCU 16KB Flash | Microchip
PIC24FV16KA302-I/ML

PIC24FV16KA302-I/ML - 16-bit 32MHz XLP MCU 16KB Flash | Microchip

The Microchip Technology PIC24FV16KA302-I/ML is a 16-bit Flash microcontroller from the PIC24F XLP (eXtreme Low Power) family, featuring a 32 MHz maximum CPU clock, 16 KB (5.5K x 24 instruction words) of program Flash, 2 KB of RAM, and 512 bytes of EEPROM in a 28-pin QFN (6x6 mm) package. The "FV" device variant operates across a wide 1.8 V to 3.6 V supply range (with 5 V tolerant digital inputs), distinguishing it from the non-"F" PIC24F variants that share the same silicon footprint. A 16-bit microcontroller (MCU) is a programmable processor core with 16-bit datapath registers, instruction fetch width, and ALU, allowing efficient C-code execution and DSP-style operations compared to 8-bit MCUs. The PIC24F sits in the hierarchy: microcontroller -> embedded processor -> semiconductor device, and the XLP variant targets ultra-low-power applications through deep-sleep operating modes that retain RAM and peripheral state. Key features include 17 general-purpose I/O pins, a 12-bit A/D converter with up to 16 input channels, a Charge Time Measurement Unit (CTMU) for capacitive touch and precise time measurement, five 16-bit timers, two UART/SPI/I2C™ modules, and a Real-Time Clock/Calendar (RTCC) that continues incrementing in deep sleep. XLP technology adds features such as Deep Sleep Brown-Out Reset (DSBOR), Deep Sleep Watchdog Timer (DSWDT), and a low-power RTCC drawing microamp-level current for battery-backed timekeeping. The PIC24FV16KA302-I/ML is built on an enhanced 16-bit modified Harvard architecture with a 24-bit instruction word, single-cycle hardware multiply, and a deterministic interrupt response suitable for real-time control loops. Its wide supply range and 5 V-tolerant I/O allow direct interfacing to legacy 5 V sensors without level shifters, simplifying mixed-voltage designs. Typical applications include battery-powered IoT sensor nodes, wearable health monitors, energy-harvesting devices, remote controls, low-power wireless sensor hubs, and any general-purpose 16-bit embedded controller where idle current and RTC retention are critical. The CTMU peripheral also enables capacitive touch buttons and sliders. When designing with this MCU, prioritize using the deep-sleep modes (DSBOR + RTCC) for idle current budgets below 1 µA, place a 0.1 µF decoupling capacitor adjacent to every VDD/VSS pair, and verify trace lengths on the 32 MHz system clock to avoid EMI. Program the configuration bits explicitly to lock the oscillator source and watchdog state for production firmware. This page consolidates distributor pricing, verified drop-in same-family alternatives, and practical XLP design notes not found in the manufacturer datasheet - designed for engineers comparing Microchip's 16-bit XLP lineup against competing low-power MCUs.

Cotización Contacto
PIC24FV16KA302-I/SO - 16KB Flash 16-bit XLP MCU | Microchip
PIC24FV16KA302-I/SO

PIC24FV16KA302-I/SO - 16KB Flash 16-bit XLP MCU | Microchip

The Microchip Technology PIC24FV16KA302-I/SO is a 16-bit eXtreme Low Power (XLP) microcontroller IC with 16KB (5.5K x 24) of Flash program memory, 2KB of SRAM, and 512B of EEPROM, operating at up to 32 MIPS at 32 MHz from a wide 1.8 V to 5.5 V supply, housed in a 28-pin SOIC (SO) package rated -40 C to +85 C. According to the verified manufacturer page, the PIC24FV16KA302 family is designed for battery-powered and power-constrained applications, featuring unique deep-sleep peripherals such as DSBOR, DSWDT, and RTCC that continue to operate while the CPU core is parked for industry-leading sleep current performance. What is a 16-bit microcontroller? A microcontroller (MCU) is a single-chip computer integrating a CPU, non-volatile program memory, RAM, peripherals, and I/O. A 16-bit MCU class is a microcontroller whose data path, registers, and ALU operate on 16-bit words, offering a balance between the simplicity of 8-bit parts and the throughput of 32-bit Cortex-M parts. The PIC24F sub-family uses a modified Harvard architecture with a 16-bit instruction set and 24-bit instructions, positioning it above 8-bit PIC MCUs but below 32-bit Cortex devices, while the XLP branding emphasizes extreme low power consumption. Key features include 17 general-purpose I/O, a 12-bit A/D converter with up to 16 analog inputs, a charge time measurement unit (CTMU) for capacitive touch and precise time measurement, multiple serial interfaces (UART, SPI, I2C), 5V-tolerant I/O, and on-chip op amps/comparators on select packages. The 'FV' voltage designation indicates the wide 1.8 V to 5.5 V operating range, while the 'F' (5V) variant is 1.8 V to 3.6 V - the FV part gives both 3.3 V and 5 V rail flexibility in a single die. Architecturally, the PIC24FV16KA302 uses the PIC24F CPU core running at up to 32 MHz with 16 MIPS throughput, a 2-cycle hardware multiplier, and a 16-bit DSP engine. The XLP implementation adds deep-sleep current as low as 20 nA typical with RTCC active, plus multiple low-power operating states (Doze, Sleep, Deep Sleep) controlled by the onboard RTCC and DSBOR/DSWDT. Typical applications include wearable medical devices, battery-powered IoT sensor nodes, low-power remote controls, energy harvesting systems, and capacitive touch user interfaces where deep-sleep current, wide voltage range, and integrated CTMU deliver BOM cost and PCB area savings. When designing with this device, ensure decoupling with 100 nF ceramic capacitors on VDD/VSS pairs placed close to the IC, and use the RTCC, DSBOR, and DSWDT features to maximize deep-sleep efficiency. Verify programming/debugging with the ICSP interface using PICkit or MPLAB ICD tools. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC24FV16KA302-I/SP - 16-bit XLP MCU, 16KB Flash, 28-SPDIP | Microchip
PIC24FV16KA302-I/SP

PIC24FV16KA302-I/SP - 16-bit XLP MCU, 16KB Flash, 28-SPDIP | Microchip

The Microchip PIC24FV16KA302-I/SP is a 16-bit Flash microcontroller in the PIC24F XLP family with eXtreme Low Power technology, packaged in a 28-pin SPDIP (SP) through-hole form factor operating at up to 32 MHz MIPS performance. The device integrates 16 KB of Flash program memory (5.5K x 24 words), 2 KB of SRAM, and 512 bytes of EEPROM, delivering ultra-low-power operation suitable for battery-powered and energy-harvesting applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and programmable peripherals into one package. Microcontrollers in the PIC24F class are 16-bit modified-Harvard RISC architectures from Microchip Technology, sitting above 8-bit PIC10/12/16 MCUs and below 32-bit PIC32 devices in the company's product hierarchy. Within the PIC24F family, the FV16KA3xx sub-series is positioned for ultra-low-power general-purpose applications, competing with low-power ARM Cortex-M0+ MCUs from STMicroelectronics, NXP, and Renesas in the eXtreme Low Power (XLP) tier. Distinguishing features of this part include 17 general-purpose I/O pins, integrated 12-bit ADC with up to 16 input channels, 5-bit DAC, multiple timers (Timer1, Timer2/3, RTCC), I2C, SPI, UART peripherals, and CTMU for capacitive touch sensing. The 'FV' prefix confirms a wide VDD range of 2.0 V to 5.5 V, supporting both 3.3V and 5V system rails, while the 'I' suffix denotes the -40C to +85C industrial temperature grade. Typical applications include portable medical devices, IoT sensor nodes, wearable fitness bands, industrial sensor hubs, and battery-powered wireless accessories where Deep Sleep currents in the order of 20-50 nA extend coin-cell battery life to multiple years. When designing with this part, place the ICSP programming header footprint on the board even in production designs - this allows in-field firmware updates without desoldering the MCU.

Cotización Contacto
PIC24FV16KA302-I/SS - 16-Bit XLP MCU, 16KB Flash, 28-SSOP | Microchip
PIC24FV16KA302-I/SS

PIC24FV16KA302-I/SS - 16-Bit XLP MCU, 16KB Flash, 28-SSOP | Microchip

The Microchip PIC24FV16KA302-I/SS is a 16-bit PIC® microcontroller with eXtreme Low Power (XLP) technology, 16KB Flash, 2KB RAM, and 32 MHz (16 MIPS) operation, supplied in a 28-pin SSOP package. The wide 1.8V to 5.5V supply range and integrated features target power-constrained and battery-powered designs across consumer, industrial, and medical segments. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), and on-chip peripherals such as timers, ADC, communication interfaces, and I/O. The PIC24F family uses a 16-bit modified Harvard RISC architecture that delivers up to 16 MIPS while retaining the PIC instruction set's deterministic, single-cycle characteristics. XLP variants add power-management hardware such as Deep Sleep mode with DSBOR (Deep Sleep Brown-Out Reset), DSWDT (Deep Sleep Watchdog Timer), and a real-time clock calendar (RTCC) that runs while the core is asleep. Key features include 16KB (5.5K x 24) self-programmable Flash, 2KB SRAM, 512 bytes EEPROM, a 12-bit ADC with up to 16 input channels, a Charge Time Measurement Unit (CTMU) for capacitive touch and precise timing, and a 17-bit Single Cycle 16x16 Multiply hardware engine. The 5V-tolerant I/O allows direct interface with legacy 5V logic or analog signal-conditioning front-ends without level shifters. The architecture supports two supply rails — a 3.3V VDD for the core and an optional 5V-tolerant AVDD for analog — and peripherals include UART, SPI, I2C, and a parallel master port (PMP). Microchip's MPLAB X IDE with the XC16 compiler provides a full tool chain for code development and on-chip debugging, including built-in support for the device's unique low-power modes. Typical applications include low-power wireless sensor nodes, battery-powered medical instruments such as glucose meters, e-metering data loggers, and consumer remote controls. The CTMU and 12-bit ADC combination also suits capacitive-touch user interfaces. The 28-SSOP package gives a 0.65 mm pitch and a low ~1.75 mm profile, making it suitable for compact hand-held enclosures. When designing with the PIC24FV16KA302-I/SS, evaluate the VDD/AVDD decoupling network (typically 0.1 µF X7R per rail plus 10 µF bulk) and route the analog and digital grounds as a star to minimize ADC noise. Verify that the chosen sleep mode meets the application's average current budget — Deep Sleep draws only nanoamps while still waking on RTCC or external interrupts. This page synthesizes distributor pricing, drop-in PIC24F/dsPIC alternatives in the same SSOP-28 footprint, and practical low-power design notes not collected in the manufacturer datasheet.

Cotización Contacto
PIC24FV16KA302T-I/ML - 16-bit XLP MCU, 32MHz, 16KB Flash | Microchip
PIC24FV16KA302T-I/ML

PIC24FV16KA302T-I/ML - 16-bit XLP MCU, 32MHz, 16KB Flash | Microchip

The Microchip Technology PIC24FV16KA302T-I/ML is a 16-bit PIC® XLP™ (eXtreme Low Power) microcontroller running at up to 32 MHz (16 MIPS) from a 1.8 V to 3.6 V supply, integrating 16 KB Flash program memory, 2 KB SRAM, and 512 B EEPROM into a 28-pin QFN package (6x6 mm). It is part of the PIC24FV16KA304 family of 20/28/44/48-pin general-purpose 16-bit Flash microcontrollers featuring XLP Technology. The 'FV' in the part number designates the wide 1.8 V to 3.6 V supply variant, ideal for battery-powered applications. What is a Microcontroller (MCU)? A microcontroller is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM and EEPROM), and programmable peripherals on one die. An MCU hierarchy looks like: 16-bit MCU -> microcontroller -> embedded controller -> semiconductor -> integrated circuit. The 16-bit MCU class typically delivers 10-100 MIPS with deterministic interrupt response, sitting between 8-bit MCUs (lower cost, lower performance) and 32-bit ARM Cortex-M MCUs (higher performance, larger code). The PIC24F family is renowned for ultra-low-power XLP technology with sub-uA deep-sleep current. Key differentiating features include eXtreme Low Power (XLP) technology with sub-uA Deep Sleep current, 12-bit ADC with up to 16 channels, Charge Time Measurement Unit (CTMU) for capacitive touch sensing, Real-Time Clock and Calendar (RTCC) that runs even in Deep Sleep mode, plus DSBOR and DSWDT (Deep Sleep Brown-Out Reset and Deep Sleep Watchdog Timer). The 'T' suffix denotes tape-and-reel packaging; the 'I' indicates the industrial -40 °C to +85 °C operating temperature range. The device is built on a Harvard-architecture PIC24F CPU core with 16-bit instructions, allowing compact code density. The CTMU peripheral enables touch buttons, sliders, and proximity sensing. The integrated RTCC eliminates external clock chips for time-stamped data logging in low-power products. With 17 user I/O pins in the 28-QFN variant, the device provides flexible mixed-signal design. Typical applications include IoT sensor nodes, wearable fitness devices, handheld instrumentation, low-power wireless sensor networks, capacitive touch user interfaces, and battery-powered industrial data loggers. The Deep Sleep modes with running RTCC enable years of operation from a single coin cell. When designing with this MCU, choose the device's integrated RTCC over external RTC chips when PCB real estate and BOM cost matter. Always characterize sleep-mode entry/exit timing against worst-case Wake-from-Sleep scenarios. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC24FV16KA302T-I/SO - 16-bit MCU, 32MHz, 16KB Flash | Microchip
PIC24FV16KA302T-I/SO

PIC24FV16KA302T-I/SO - 16-bit MCU, 32MHz, 16KB Flash | Microchip

The Microchip Technology PIC24FV16KA302T-I/SO is a 16-bit Flash microcontroller from the PIC24F XLP family, delivering 32 MIPS performance at 32 MHz with 16 KB Flash program memory, 2 KB RAM, and 512 B EEPROM. It operates across a wide 1.8 V to 3.6 V supply range (5 V tolerant I/O) and is housed in a 28-pin SOIC package. A 16-bit microcontroller (MCU) is a microprocessor that processes data and addresses in 16-bit widths, providing higher throughput and richer peripherals than 8-bit MCUs while consuming less power than many 32-bit parts. PIC24F devices belong to the broader category of microcontrollers (MCUs) within integrated circuits (ICs), positioned between 8-bit PIC16/PIC18 and 32-bit PIC32 in Microchip's portfolio. The XLP (eXtreme Low Power) designation indicates ultra-low sleep current with peripheral operation in Deep Sleep mode. Key features include 17 general-purpose I/O pins, a 12-bit ADC with 16 channels supporting up to 500 ksps conversion rate, a Charge Time Measurement Unit (CTMU) for capacitive touch sensing, multiple communication interfaces (UART, I2C, SPI), 5 CCP/ECCP modules, RTCC with Deep Sleep, and on-chip DSBOR/DSWDT low-power brown-out and watchdog timers. The PIC24FV variant supports 5V operation on I/O lines, enabling direct interface to legacy 5V systems. The PIC24FV16KA302T-I/SO uses a modified Harvard RISC architecture with a 16-bit wide datapath and dual-bus memory fetch, executing most instructions in one cycle. The 16 KB self-programmable Flash supports ICSP (In-Circuit Serial Programming) via PGECx/PGEDx pin pairs, with code-protection features that prevent unauthorized read-back. CTMU hardware enables mTouch capacitive touch sensing with no external components beyond sensor electrodes. Typical applications include battery-powered sensor nodes, capacitive touch user interfaces, low-power IoT endpoints, consumer electronics with 5V mixed-signal interfaces, and industrial control modules requiring 16-bit math performance with extended battery life. When designing with this part, place a 0.1 µF decoupling capacitor as close to VDD as possible. Use the RTCC with Deep Sleep to wake the MCU at scheduled intervals, keeping active current below the 1 µA Deep Sleep range for maximum battery life. This page synthesizes XAIPART distributor pricing, drop-in PIC24F family alternatives, CTMU/Deep Sleep design notes, and cross-brand comparisons not found in the manufacturer datasheet alone.

Cotización Contacto
PIC24FV16KA304-E/MV - 16KB Flash XLP 16-Bit MCU 32MHz | Microchip
PIC24FV16KA304-E/MV

PIC24FV16KA304-E/MV - 16KB Flash XLP 16-Bit MCU 32MHz | Microchip

The Microchip Technology PIC24FV16KA304-E/MV is a 16-bit PIC24F microcontroller from the eXtreme Low Power (XLP) family, featuring 16KB of Flash program memory (5.5K x 24 words), 2KB of SRAM, and 512 bytes of EEPROM. The device operates at up to 32MHz delivering 16 MIPS and is housed in a 48-pin UQFN (MV) 6x6mm package with an exposed thermal pad. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), non-volatile data storage (EEPROM), and a rich set of peripherals on one silicon die. PIC24F XLP microcontrollers belong to the broader 16-bit microcontroller family and are positioned within Microchip's portfolio as ultra-low-power MCUs optimized for battery-powered and energy-harvesting applications. Key features include a wide operating voltage range of 2.0V to 5.5V, ultra-low-power operation with sub-uA sleep currents, integrated 12-bit ADC, CTMU (Charge Time Measurement Unit) for capacitive touch sensing, Real-Time Clock and Calendar (RTCC) with Deep Sleep retention, DSBOR and DSWDT ultra-low-power supervisory peripherals, and multiple communication peripherals including UART, SPI, and I2C. The wide voltage range supports both 3.3V and 5V system designs without external level translation. Architecturally, the PIC24FV16KA304 uses a 16-bit modified Harvard CPU with a 24-bit instruction word, achieving deterministic interrupt response and 16 MIPS throughput. The 'FV' voltage variant supports 5.5V VDD operation while the 'F' variant tops out at 3.6V, making the FV version ideal for mixed 3.3V/5V analog signal chains. The integrated CTMU enables touch button or capacitive proximity sensing without external analog ICs. Typical applications include battery-powered IoT sensor nodes, wearable health and fitness devices, remote controls and human interface panels, low-power wireless sensor networks, energy harvesting systems, and consumer electronics requiring capacitive touch buttons. The Deep Sleep mode with RTCC retention makes the part especially suitable for applications that spend >99% of operating life in sleep state. When designing with this device, consider the trade-off between using the on-chip 12-bit ADC versus an external precision ADC: the internal ADC is convenient but limited to 12-bit resolution and approximately 200 ksps. For applications requiring higher precision, an external 16-bit or 24-bit delta-sigma ADC may be paired with the MCU via SPI. This page synthesizes distributor pricing, drop-in alternatives within the PIC24F XLP family, and practical design notes that go beyond what is found in the manufacturer datasheet alone.

Cotización Contacto