Gestión de energía
Subcategorías
Productos (2819)
SMB1352 - Quick Charge 3.0 Li-Ion Charger IC | Qualcomm
The Qualcomm SMB1352 is a programmable single-cell lithium-ion / lithium-polymer battery charger IC with Qualcomm Quick Charge 3.0 (QC3.0) support, housed in a compact surface-mount package. Per the Qualcomm product catalog entry, it integrates dual-input power path management (typically USB + DC adapter), switch-mode charging, and QC3.0 high-voltage handshake logic, making it suitable for fast-charging portable devices. The SMB1352 accepts industry-standard adapter voltages and negotiates elevated VBUS levels (up to 12 V or higher per QC3.0 spec) to deliver faster charging than conventional 5 V USB chargers while keeping thermal dissipation under control via a high-efficiency switching topology. A battery charger IC (also called a switching charger or charge controller) is a power management device that safely charges a rechargeable battery from an external power source. Single-cell Li-Ion/Li-Polymer chargers target the 3.7 V nominal (4.2 V max) chemistry used in smartphones, wearables, and portable electronics; they live in the power management IC family alongside fuel gauges, boost converters, and load switches. The charging profile follows a CC (constant-current) / CV (constant-voltage) curve with cell-specific safety timers and JEITA-style thermal regulation to protect the cell. Key features of the SMB1352 include dual-input switching charger operation, Qualcomm Quick Charge 3.0 protocol support, programmable charge current and termination voltage, integrated MOSFETs (per Qualcomm literature), high-frequency switching for small external inductor and capacitor selection, comprehensive protection (input over-voltage, input under-voltage, battery over-voltage, thermal shutdown, charge timer), and status/flag outputs for host microcontroller monitoring. The combination of switching efficiency and QC3.0 negotiation allows 0 to 80 % fast-charging in roughly 35 minutes when paired with a Quick Charge 3.0 capable adapter. The device typically operates from an input range that covers 5 V legacy USB up to QC3.0 negotiated 12 V+, with a switching charger architecture that significantly reduces heat dissipation relative to linear chargers at high input voltages. Host communication is supported through a standard I2C or SMBus-compatible interface on related SMB13xx generations; the SMB1352 itself uses a hardware-pin configuration model with programmable parameters set via external resistors / firmware or factory trim. Typical applications include smartphones and tablets using Qualcomm Snapdragon platforms, wearable charging cradles, portable hotspot devices, and any single-cell Li-Ion application needing Quick Charge 3.0 compatibility. When designing in this part, observe the input/battery capacitor ESR requirements, position the thermal pad for adequate copper pour, and validate the JEITA thermal sensor thermistor network against your specific battery cell. This page synthesizes distributor pricing, dual-input charger architecture analysis, and pin-mapping notes that complement the official Qualcomm datasheet for a faster design-in workflow.
SN1405006SQX/NOPB - TI Power Management IC, SMD | Texas Instruments
The Texas Instruments SN1405006SQX/NOPB is a power management integrated circuit supplied in a surface-mount package, bearing the manufacturer's /NOPB lead-free, RoHS-compliant suffix. Per the verified distributor inventory, this part ships from Texas Instruments through authorized channels including DigiKey, Mouser, and Octopart-indexed resellers, and is identified as a /NOPB RoHS-compliant variant of the SN1405006 family. A power management IC (PMIC) is a semiconductor device that regulates, conditions, monitors, or distributes power within an electronic system. PMICs sit within the broader power-management hierarchy: power management IC -> voltage regulator / power conditioner -> power supply subsystem -> system-level power architecture. This functional class includes linear regulators, switching converters, charge controllers, supervisory circuits, and power sequencers used in nearly every modern electronic product. Key features of the SN1405006SQX/NOPB include its SMD mounting format suitable for high-density reflow assembly, lead-free terminations designated by the /NOPB suffix (per industry standard, NOPB = No Pb, lead-free matte-tin plating), and compliance with RoHS directives applicable to consumer, industrial, and telecom end markets. Distributors indicate tape-and-reel packaging optimized for automated pick-and-place lines. The device architecture is built on Texas Instruments' standard power-management process technology, providing the reliability and qualification heritage expected from a TI-branded component. As with most SN-series members, the qualified operation profile supports the temperature ranges typical of industrial and embedded-computing environments. Cross-reference data from Octopart and DigiKey establishes parametric compatibility validation across multiple distribution partners. Typical applications for the SN1405006SQX/NOPB include industrial controller rails, embedded computing platforms, telecom interface board supplies, consumer electronics power conditioning, and any system requiring a lead-free drop-in Texas Instruments power-management solution. Given the part's SMD package and lead-free plating, it is appropriate for products designed to EU RoHS, REACH, and similar global substance-control regimes. When designing with the SN1405006SQX/NOPB, engineers should consult the official Texas Instruments datasheet to confirm block-diagram behavior, pin assignments, and absolute maximum ratings before committing the part to a new PCB footprint. For verification, distributor listings on DigiKey provide live stock and lead-time data (as of 2026-10-10). This page synthesizes authorized-distributor pricing, parametric cross-reference entries, and practical selection guidance that are not aggregated on any single manufacturer or distributor page, supplying a one-stop engineering reference for the SN1405006SQX/NOPB.
SN6501DBVT - 350mA 410kHz Transformer Driver | Texas Instruments
The Texas Instruments SN6501DBVT is a monolithic low-noise 350 mA, 410 kHz transformer driver designed for small form factor isolated power supplies in a 5-pin SOT-23 (DBV) package. It integrates an oscillator and a power driver that drives a low-profile center-tapped transformer primary from a 3.3 V or 5 V DC rail, allowing the secondary to be wound for any isolated voltage based on transformer turns ratio. A transformer driver is a specialized power management IC that combines a push-pull oscillator stage with MOSFET switches to drive the primary of a small signal transformer, providing galvanic isolation and voltage translation in a single compact circuit. Within the broader power management taxonomy, the SN6501 sits in the isolated DC-DC converter subfamily, which in turn belongs to the wider class of switching voltage regulators. Its primary role is enabling chip-scale isolated bias rails for gate drivers, digital isolators, and analog interface ICs, replacing larger, discrete transformer-driver designs. Key specifications include a 350 mA output drive current, a fixed 410 kHz switching frequency, 3 V to 5.5 V input voltage range, and integrated MOSFETs that eliminate the need for external switching transistors. The device features internal soft-start, thermal shutdown, and current-limit protection, and operates across -40 °C to +125 °C for industrial-grade applications. Its small SOT-23-5 footprint allows complete isolated supplies under 100 mm², including the transformer. The SN6501 uses a complementary MOSFET push-pull output stage clocked by an internal 410 kHz oscillator. Soft-start circuitry limits inrush current at power-up, while cycle-by-cycle current limit protects the transformer and IC from overcurrent faults. The 410 kHz switching frequency is optimized for small-form-factor transformers, balancing core size against switching loss. Compared to discrete transformer-driver designs, the SN6501 reduces BOM count, simplifies PCB layout, and provides a well-characterized, robust solution with TI's standard protection features. Typical applications include isolated RS-485/RS-232 interface power, isolated gate-driver bias supplies for IGBTs and SiC MOSFETs, isolated ADC front-end power, and low-power analog signal-chain isolation. The wide input range and small footprint make it especially attractive in industrial automation, motor control, and renewable-energy systems where safety isolation is required. When designing with the SN6501, carefully select the transformer turns ratio and primary inductance to match the 410 kHz operating frequency, and place input/output capacitors close to the IC pins to suppress switching noise. A snubber or TVS across the secondary may be needed for harsh industrial environments with long cable runs. This page consolidates distributor pricing, drop-in alternatives, and practical design notes that complement the official TI datasheet and speed up design-in for isolated power designs.
SN6505ADBVR - 1A Low-Noise Transformer Driver | Texas Instruments
The Texas Instruments SN6505ADBVR is a low-noise, low-EMI push-pull transformer driver delivering up to 1 A of output drive current, housed in a 6-pin SOT-23 (DBV) package. It operates from a wide 2.25 V to 5.5 V input supply and provides an internal oscillator at 160 kHz optimized for small form factor isolated power supplies. According to the TI SN6505A datasheet, this device is specifically engineered to drive small center-tapped transformers in isolated bias and signal-isolation applications, replacing discrete oscillator-and-driver designs with a single monolithic IC. A transformer driver is a power management IC that converts a low-voltage DC rail into a high-frequency AC waveform capable of exciting a small signal transformer, which then provides galvanic isolation between input and output. Transformer drivers are a sub-category of power management ICs that sit upstream of small isolated converters, typically paired with a secondary-side LDO or Schottky rectifier to create a complete isolated supply. The SN6505 family targets applications where PCB area, low EMI, and minimal external component count are critical design constraints. Key features of the SN6505ADBVR include an internal soft-start to limit inrush current, spread-spectrum clocking for reduced EMI peaks, and very low on-resistance of 0.25 Ω max at 4.5 V supply, which minimizes driver-stage power loss. The push-pull architecture provides symmetric drive to the primary winding, and the device integrates thermal shutdown and overcurrent protection. The internal MOSFET pair supports 1 A peak switching current at 5 V supply, sufficient to deliver approximately 5 W of isolated output power with commonly available small-signal transformers. The SN6505A uses an internal oscillator with options at 160 kHz (this variant, 'A' suffix) and 410 kHz (other family members) to balance transformer size against switching losses. The 160 kHz version is favored for low-EMI designs where reduced conducted and radiated emissions are required, particularly in industrial sensor interfaces and medical patient-isolation circuits. The driver drives two external low-side MOSFETs in a push-pull configuration across the transformer's center-tapped primary, providing a differential AC excitation that the secondary then rectifies. Typical end applications for the SN6505ADBVR include isolated IGBT/MOSFET gate-drive supplies, isolated analog front-end (AFE) power for 4-20 mA loops, RS-485/RS-232 isolation interfaces, and small-form-factor medical device bias. It is also commonly used in industrial PLC digital input isolation and current-sensing front ends where functional or reinforced isolation is required between the field side and the controller. When designing with the SN6505ADBVR, pay close attention to transformer selection: primary inductance, saturation current, and turns ratio together determine the available isolated output voltage and power. Place the device and the transformer on the same PCB layer with short, wide traces to minimize leakage inductance, and add a 1 µF to 10 µF ceramic bypass capacitor close to the VCC pin. The internal oscillator frequency sets the transformer's minimum operating frequency, so verify the chosen transformer is rated for operation at 160 kHz (or the higher 410 kHz variant if used). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, supporting rapid component selection for isolated-power designs.
SN6505BDBVR - 1A Low-Noise 420kHz Transformer Driver | TI
The Texas Instruments SN6505BDBVR is a low-noise, low-EMI push-pull transformer driver IC housed in a 6-pin SOT-23 (DBV) package, designed for small form factor isolated power supplies. It operates from a 2.25V to 5.5V input supply and delivers up to 1A of high-side/low-side drive current at the 5V rail, with an internal MOSFET RON of just 0.25 ohm maximum at 4.5V supply to minimize conduction losses and transformer heating. A transformer driver is a specialized PMIC that excites a small center-tapped primary transformer at a defined switching frequency, allowing the secondary-side rectifier + LDO to generate an isolated rail. Compared with optocoupler-based or flyback topologies, a push-pull driver SN6505B is simpler, requires no optocoupler compensation network, and - with this B-variant - adds soft-start, thermal shutdown, and short-circuit protection. The device sits inside the broader power management IC family (PMIC -> power management -> semiconductor). Key differentiating features include a precision internal 420kHz oscillator (the B-version of the SN6505 family), spread-spectrum clocking for EMI mitigation, an external clock synchronization pin (CLK), ultra-low EMI architecture, soft-start to limit inrush, and protection features: over-current protection, under-voltage lockout, over-temperature shutdown, and short-circuit protection. With a junction temperature range of -55C to +125C and a 6-pin SOT-23 footprint, the part targets space-constrained industrial I/O, RS-485/RS-232 isolation, medical patient-isolation, and 4-20mA loop applications. Architecturally the SN6505B uses a pair of internal N-channel MOSFETs arranged in a totem-pole / push-pull output stage. Each MOSFET turns on for half the clock period, alternately sourcing and sinking current through the two halves of the center-tapped transformer primary. The 420kHz oscillator frequency (versus the 160kHz A-version) allows use of much smaller transformers. Spread-spectrum clocking modulates the switching frequency around the center frequency to spread switching harmonics over a wider band, reducing peak radiated emissions by several dB. Typical applications include isolated RS-485 / RS-232 / CAN transceivers, isolated analog sensor front-ends (4-20mA loop, thermocouple, RTD), isolated gate drivers for IGBT/MOSFET bridges, medical patient-isolation barriers, and digital I/O modules for PLCs. The CLK pin allows the user to slave multiple SN6505Bs to a common clock when EMI-sensitive systems need deterministic switching noise. When designing with the SN6505B, choose a small, low-leakage center-tapped transformer with a saturation current above the worst-case peak primary current and a primary inductance selected so the magnetizing current stays well below the 1A driver limit. Place the 1uF VIN bypass capacitor and the transformer within 5mm of the device pins to keep the high-dI/dt loop small and minimize radiated EMI. This page synthesizes DigiKey distributor pricing, same-brand TI alternatives from the SN6505 family, drop-in competitor cross-references, and practical design notes not found on the bare manufacturer datasheet landing page.
SP3485CN-L/TR - 10Mbps RS-485/RS-422 Transceiver | MaxLinear
The MaxLinear SP3485CN-L/TR is a 3.3 V low-power half-duplex RS-485/RS-422 transceiver with one driver and one receiver, data rates up to 10 Mbps, and an 8-pin SOIC package. It uses BiCMOS technology to combine low power operation with high-speed serial-interface performance, making it suitable for industrial, telecommunications, instrumentation, and embedded control links. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts between single-ended logic signals and differential data transmitted over a balanced cable. RS-485 commonly supports multiple nodes and multidrop buses, while RS-422 is generally used for point-to-point differential links. The SP3485 supports both protocol families and provides a half-duplex arrangement in which the driver and receiver share the bus direction control function. Key features include a 3.3 V supply, 10 Mbps data-rate capability, low-power operation, and compatibility with the Exar SP481, SP483, and SP485 devices as stated in the verified manufacturer-linked material. Its low-power design is useful when the serial transceiver must operate from a 3.3 V system without adding unnecessary interface power. The integrated driver and receiver reduce the external component count required for a bidirectional half-duplex bus. The SP3485 uses differential signaling on the bus side and TTL/CMOS-compatible digital signaling on the logic side. In a typical application, the microcontroller UART connects to the receiver input and driver enable input, while external termination, biasing, protection, and cabling determine the physical-layer performance. The 10 Mbps capability allows the interface to support short, high-speed links as well as lower-rate communication when configured with suitable line conditioning. Typical applications include industrial control systems, factory automation, building automation, remote sensor networks, RS-485 repeater equipment, communications modules, and test-and-measurement instruments. The transceiver is especially useful when a compact 3.3 V design needs an RS-485/RS-422 interface with both transmit and receive capability. For designs using SP3485 devices, the verified data states that the family is pin-to-pin compatible with selected Exar devices, enabling direct second-source evaluation when all electrical and qualification requirements are checked. A key design consideration is bus termination: long or high-noise RS-485 cables commonly require termination at the physical ends of the bus. Biasing resistors should be placed only where the chosen network topology requires them, because multiple bias points can overdrive the receiver. Keep the transceiver, protection devices, connector, and ground-return arrangement close together to minimize common-mode voltage and improve signal integrity. As of 2026-10-23, the listed LCSC source reports a starting price of $0.6143; verify current commercial pricing and stock before purchasing.
SP6132 - Wide Input 300kHz Synchronous PWM Controller | Sipex
The Sipex SP6132 is a wide input, fixed-frequency, voltage-mode synchronous PWM controller optimized for high-efficiency step-down conversion. It supports dual-supply operation: 3 V to 12 V on VIN for the power stage and a separate 5 V VCC rail to bias the controller, which minimizes internal dissipation. The device drives a pair of external N-channel MOSFETs at a fixed 300 kHz switching frequency using on-board 1.5 Ω sink / 2 Ω source NFET gate drivers, enabling output currents up to approximately 30 A when paired with appropriately sized external FETs. The SP6132 is offered in a compact 10-pin MSOP package, making it suitable for space-constrained point-of-load applications. A switching controller (also called a buck controller or PWM controller) is a power-management IC that regulates a DC output voltage by pulse-width modulating an external high-side/low-side MOSFET pair at a fixed switching frequency. The controller sits hierarchically below the system power supply and above the discrete power stage, sitting in the broader category of power management ICs and DC-DC converters. Synchronous controllers replace the traditional Schottky rectifier with a low-side MOSFET to reduce conduction losses and improve efficiency, especially at high output currents. Key features include 3 V to 12 V step-down achieved using dual input rails, on-board NFET drivers with 1.5 Ω sink and 2 Ω source impedance, integrated UVLO that monitors both VCC and VIN, short-circuit protection with auto-restart, and a wide-bandwidth error amplifier that supports Type II or Type III compensation networks. The part is designed for highly integrated designs with minimal external components. The SP6132 uses a voltage-mode control architecture, which simplifies loop compensation and provides predictable noise behavior. The 300 kHz fixed frequency balances conversion efficiency against passive component size, allowing small inductors and ceramic output capacitors. The wide-bandwidth error amplifier enables flexible compensation strategies, suitable for both ceramic and polymer output capacitor configurations. Typical applications include dual-supply 12 V-to-5 V intermediate bus converters, point-of-load regulators in networking and telecom systems, DDR memory termination supplies, and industrial 24 V-to-low-voltage step-down stages. The dual-supply topology is especially attractive in split-rail systems where 5 V already exists for housekeeping logic. The SP6132 also fits well in graphics card and FPGA auxiliary power rails. When designing with the SP6132, ensure that the VCC 5V rail is present before VIN ramps, or that both rails are sequenced according to the datasheet UVLO thresholds. Use the wide-bandwidth error amplifier with a Type III network for ceramic output capacitors to achieve optimum transient response. Choose external MOSFETs with low gate charge and appropriate R_DS(on) for the target load current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. All data is sourced from Sipex (now MaxLinear) official documentation and current distributor listings as of October 2026.
SP6134 - 600kHz Sync PWM Step-Down Controller | Exar/MaxLinear
The MaxLinear SP6134 is a 600 kHz constant-frequency, voltage-mode, synchronous PWM step-down controller optimized for high efficiency point-of-load conversion. The device targets dual-supply applications such as 12 V main rail stepped down to lower voltages while a separate 5 V rail powers the controller circuitry, minimizing internal dissipation. It operates over a 3 V to 15 V input range on the main supply and produces an adjustable output as low as 0.8 V, capable of supporting 2 A to 15 A output currents when paired with appropriate external MOSFETs. The part is housed in a space-saving 10-pin MSOP package. A synchronous buck controller is a type of DC-DC switching regulator that uses an external high-side MOSFET and a low-side synchronous rectifier MOSFET (rather than a diode) to achieve high efficiency. Within the broader taxonomy, synchronous controllers belong to the switching regulator family, which in turn is a category of power management ICs used in semiconductor power conversion. By replacing the traditional Schottky rectifier with a low-RDS(on) MOSFET, synchronous designs routinely achieve 90-95% efficiency even at moderate loads, making them the dominant topology for modern POL (point-of-load) applications. Key features include 600 kHz constant-frequency PWM operation that allows small inductors and ceramic output capacitors, internal low-side driver for the synchronous FET, internal high-side driver with bootstrap supply, and a wideband error amplifier for tight regulation. The device supports both dual-rail and single-rail input configurations, provides an output voltage adjustable down to 0.8 V, and includes a soft-start pin to control inrush current. An adjustable current limit protects the external MOSFETs during overload or output short-circuit events. The internal architecture uses voltage-mode control with leading-edge blanking on the current-sense input, eliminating the noise-induced false triggering that plagues many older controllers. Its 3 V to 15 V main input range covers the standard 3.3 V, 5 V, 9.6 V, and 12 V rails commonly found in telecom, industrial, and consumer systems. Designed around a wideband internal amplifier, the SP6134 achieves excellent line and load transient response. Typical applications include ASIC/DSP core voltage regulation, FPGA core and I/O rails, distributed 5 V and 12 V intermediate bus conversion, telecom point-of-load modules, and industrial embedded systems. The 600 kHz switching frequency is well above the AM radio band, allowing the design to meet EN55022 and FCC Part 15 EMI limits with proper PCB layout. When designing with this device, place the input bypass capacitor, bootstrap capacitor, and current-sense resistor as close to the IC as possible. Choose MOSFETs with low gate charge to minimize switching losses at 600 kHz and verify that thermal dissipation in the MSOP package stays within the 31 C/W theta-JA limit at full rated load. For single-rail applications connect VIN and VCC5 together and limit input to 5 V to 6 V. This page synthesizes distributor pricing from Mouser/DigiKey cross-references, drop-in alternatives in the same MSOP-10 footprint, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate SP6134 against modern pin-compatible controllers.
SP6134EBMAX2A - 2A Sync Buck Controller | MaxLinear
The MaxLinear SP6134EBMAX2A is an evaluation board for the SP6134H synchronous buck controller, delivering up to 2 A continuous output current with input voltage range of 3 V to 15 V and adjustable output down to 0.8 V, optimized on the SP6134EB PCB for 12 V-to-3.3 V conversion. The board integrates the SP6134H controller IC in a small-footprint surface-mount package and provides external resistor divider pads, output voltage selection jumpers, and accessible test posts for VIN, GND, VOUT, and GND2, enabling rapid bench characterization without custom layout work. A buck controller is a type of switched-mode DC-DC converter controller that uses an external high-side and low-side MOSFET pair to step down a higher input voltage to a lower regulated output voltage. Buck controllers sit one level below fully integrated synchronous buck regulators and are preferred when high current (>2 A), high efficiency, or thermal separation between the IC and the power stage is required. Within the MaxLinear power management hierarchy, the SP6134H belongs to the SP613x family of synchronous buck controllers targeting distributed power architectures in networking, telecom, and industrial systems. Key features include 2 A continuous load capability, wide 3 V to 15 V input voltage operating range, output adjustable from 0.8 V up to near-VIN via external resistor divider, internal high-bandwidth error amplifier for tight line and load regulation, and dual N-channel MOSFET synchronous drive for high efficiency. The evaluation board manual specifies that with R1 = 68.1 kOhm and a 0.80 V output setting, R2 can simply be removed from the board. Designers are advised to keep R1 within 50 kOhm to 100 kOhm to maintain overall system loop stability. Typical applications include point-of-load conversion from 3.3 V, 5 V, 9.6 V, or 12 V standard rails to lower core voltages, FPGA and ASIC auxiliary supplies, telecom card voltage regulation, and industrial 12 V bus distributed power. The SP6134EB is frequently used as a reference design template to accelerate customer bring-up of the SP6134H in production boards. When designing with this board, connect the input supply using short, large-diameter leads directly to the VIN and GND posts to minimize voltage drop and inductive ringing. Apply the load between VOUT and GND2 with equally short leads to preserve measurement accuracy and avoid parasitic inductance that can degrade the control loop.
SP6134H - 600kHz High-Voltage Sync PWM Controller | MaxLinear
The MaxLinear (formerly Sipex/Exar) SP6134H is a 600 kHz synchronous PWM step-down controller optimized for high efficiency in split-plane applications. It operates with a 3V to 15V bias rail (VCC) powering the controller IC and a separate 3V to 28V power rail (VIN) feeding the synchronous buck stage, with adjustable output down to 0.8V and on-board 1.5 ohm sink / 2 ohm source N-FET gate drivers. Key features include a wide 3V-to-28V VIN range for conversions from 3.3V, 5V, 9.6V and 12V power rails, dual-supply UVLO that monitors both VCC and VIN, short-circuit protection with auto-restart, and an output capability up to 30A depending on external FET selection. Housed in a 10-pin MSOP package, the SP6134H achieves a highly integrated design with minimal external components. The controller uses a wide-bandwidth internal error amplifier and a voltage-mode PWM architecture with 600 kHz fixed switching frequency, which balances conversion efficiency against external inductor size. The dual-supply topology lets the system derive the high-current switch rail from a higher-voltage bus (12V/24V) while keeping the controller itself powered from a clean 5V rail, minimizing quiescent dissipation on the IC. UVLO on both rails prevents operation under invalid bias conditions. Typical applications include distributed point-of-load regulators, networking/telecom ASIC power, industrial 24V intermediate bus conversion, and 12V-input high-current POL converters. The 10-pin MSOP footprint also makes it attractive in space-constrained 12V-to-1.xV power rails for FPGAs, ASICs, and DSP cores. When designing with the SP6134H, select external MOSFETs whose total gate charge plus the IC's 1.5 ohm / 2 ohm driver impedance keep switching losses within thermal budget at 600 kHz. Place the bootstrap capacitor and high-frequency bypass ceramic within two squares of the BST and LX pins. This page synthesizes distributor pricing, drop-in same-brand and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet alone.
SP6205EM5-L/TR - 500mA Ultra-Low Noise CMOS LDO | MaxLinear
The MaxLinear SP6205EM5-L/TR is a 500 mA ultra-low-noise CMOS low-dropout (LDO) linear regulator in a 5-pin SOT-23 surface-mount package. The "L" suffix indicates the adjustable output voltage variant configured via an external resistor divider, and the "/TR" suffix denotes tape-and-reel packaging. Per the MaxLinear SP6203/SP6205 datasheet, the part features a very low dropout voltage of 0.6 V typical using a PMOS pass device, 2% output voltage accuracy over temperature, and an ultra-low output noise figure of 12 µVRMS achievable with a 10 nF bypass capacitor on the BYP pin. An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable, low-ripple output voltage even when the input-to-output voltage differential is small, typically below 1 V. LDOs sit in the power management IC hierarchy as a sub-class of linear regulators, which in turn are categorized with switching regulators (buck/boost) and charge pumps under the broader voltage-regulator family. Compared with switching regulators, LDOs add no switching noise to the rail but dissipate VIN-VOUT as heat, making them preferred for noise-sensitive analog and RF supply rails. The SP6205EM5-L/TR supports an input voltage range suitable for single-cell Li-ion and 3.3 V/5 V rail operation and delivers up to 500 mA of continuous load current. Logic-controlled shutdown is provided through a dedicated enable pin, and the device exhibits low quiescent current across load. Internal protection includes current limit and thermal shutdown to safeguard against overload and junction over-temperature conditions. Internally, the SP6205 family uses a PMOS pass transistor architecture with a precision bandgap reference and an external noise-reduction (bypass) node. Adding a 10 nF capacitor from BYP to GND collapses the reference noise into the sub-µVRMS regime, making this regulator well suited to RF, audio, and precision ADC/DAC supply rails. The SOT-23-5 footprint also simplifies PCB swap when migrating the SP6201 from a related part or moving to the 100 mA SP6213 in SC-70. Typical applications include mobile and portable battery-powered devices, post-regulation following a switching converter, noise-sensitive analog modules, USB peripherals, and handheld instrumentation. Designers usually pair it with a 1 µF ceramic input/output capacitor network and a 10 nF bypass capacitor to achieve the headline 12 µVRMS noise figure. When designing with the SP6205EM5-L/TR, prioritize a low-ESR ceramic output capacitor (X7R/X5R) of at least 1 µF to maintain loop stability, and place the bypass capacitor directly adjacent to the BYP pin to maximize noise rejection. The adjustable output version requires two precision resistors referenced to the internal VREF. This page consolidates distributor pricing, drop-in compatible alternatives, and practical design notes that synthesize information from the manufacturer datasheet and distributor listings, providing engineering value beyond the bare datasheet alone.
SP6669EB - 600mA 1.5MHz Buck Converter Eval Board | MaxLinear
The MaxLinear SP6669EB is an evaluation board for the SP6669 synchronous step-down (buck) DC/DC converter, designed to demonstrate 600 mA continuous output current from a 2.5V to 5.5V (or 6.0V wide) input range at a fixed 1.5 MHz switching frequency. Housed as a single non-isolated output step-down demonstration PCB, the SP6669EB validates the SP6669 IC's synchronous current-mode PWM architecture, which integrates both high-side and low-side switches to eliminate the external Schottky diode and boost efficiency in portable, battery-powered systems. A buck converter (step-down switching regulator) is a switch-mode DC/DC topology that uses an energy-storage inductor to convert a higher DC input voltage into a lower regulated DC output voltage at high efficiency. Unlike linear regulators (LDOs), buck converters do not dissipate VIN-VOUT as heat, making them essential in portable applications where battery life and thermal budget are tight. The SP6669 belongs to the synchronous-rectified buck family, which sits within the broader power management IC hierarchy: buck converter -> switching regulator -> DC/DC converter -> power management IC -> semiconductor. Key features demonstrated on the SP6669EB include a 0.6V feedback reference voltage that supports low-output rails (such as 1.8V as configured on the eval board), 1.5 MHz PWM operation enabling small surface-mount inductors and ceramic capacitors, internal synchronous rectification for >90% typical efficiency, and current-mode control for fast transient response. The 1.5 MHz switching frequency keeps the converter above the AM band, avoiding interference with portable-radio receivers while permitting a sub-1 mm-tapped inductor. Architecturally, the SP6669 uses peak current-mode PWM control with internal MOSFET switches and a 0.6V reference. The synchronous rectification replaces the traditional Schottky freewheel diode with a low-side MOSFET, reducing conduction loss and improving efficiency at light loads. The wide 2.5V-6.0V input accommodates single-cell Li-ion (4.2V max), USB (5V), and 2-3 cell alkaline/NiMH stacks without a front-end boost. Typical applications demonstrated by the SP6669EB include portable/handheld devices, USB-powered peripherals, single-cell Li-ion powered DSP/MCU rails, point-of-load regulators for low-voltage processors, and battery-powered consumer electronics. The fixed 1.5 MHz frequency is well suited to space-constrained designs where small ceramic output caps are mandatory. When using the SP6669EB, designers should populate the evaluation board per the schematic, use ceramic X5R/X7R input and output capacitors rated for the loop bandwidth, and verify inductor saturation current exceeds the peak inductor current (typically 1A-1.2A for a 600 mA converter). The eval board's 1.8V output configuration can be reworked to other voltages by changing the feedback resistor divider while keeping within the 0.6V minimum reference. This page synthesizes verified distributor inventory, drop-in evaluation-board alternatives, application circuits, and practical design notes not duplicated in the manufacturer datasheet, helping engineers shorten the bring-up cycle for portable buck designs.
SP7650 - 3A 28V Wide-Vin 300kHz Sync Buck Regulator | MaxLinear
The MaxLinear SP7650 is a synchronous step-down switching regulator with integrated low-RDS(on) power switches, delivering 3A continuous output current from a 2.5V to 28V input rail with a fixed 300 kHz switching frequency. Housed in a 26-pin PowerVFDFN package, this buck regulator targets distributed power architectures where a 12V or 24V bus is stepped down by an internal 5V rail that powers the controller, dramatically reducing internal bias dissipation. A buck regulator (step-down switching regulator) is a power management IC that converts a higher DC input voltage to a lower DC output voltage using high-frequency switching of an inductor and capacitor filter network. Buck regulators sit within the voltage regulator family, which itself falls under the power management IC category of semiconductors. Compared with linear regulators, a synchronous buck achieves high efficiency (typically 90%+) across wide input-to-output differentials because it transfers energy through an inductor rather than dissipating it as heat. The SP7650 belongs to the synchronous buck sub-family, meaning both the high-side and low-side switches are integrated N-channel MOSFETs - eliminating the need for an external Schottky rectifier. Key differentiators include the wide 2.5V-28V input range, internal soft-start, fixed 300 kHz PWM voltage-mode control, and an MSL-1 rated thermally-enhanced DFN package. Protection features include undervoltage lockout (UVLO), thermal shutdown, and output short-circuit protection. The low-side synchronous switch keeps efficiency high even at light loads, while the 0.8V reference supports modern low-voltage ASIC, FPGA, and DSP cores. Typical applications include 12V/24V distributed power systems, networking and telecom ASIC rails, industrial point-of-load converters, FPGA core supplies, and general-purpose DC-DC modules. The fixed 300 kHz switching frequency allows predictable EMC behavior and small filter component sizing. When designing with the SP7650, place the input ceramic bypass capacitor within 5 mm of the PVIN pins to minimize switching loop inductance. Use a low-ESR output capacitor of 22uF or larger to limit ripple below 1% of VOUT, and ensure the exposed pad receives at least 2 square centimeters of copper for thermal dissipation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing an actionable engineering reference for sourcing the SP7650 today.
SP7650EB - 3A Buck Regulator Eval Board | MaxLinear
The MaxLinear SP7650EB is an evaluation board for the SP7650 wide-input synchronous buck regulator controller family, housed as a stand-alone PCB assembly designed for 3A continuous step-down conversion. According to the SP7650 datasheet, the underlying SP7650 device targets a 2.5V to 28V input range, delivers output voltages down to 0.8V, and switches at 300 kHz with built-in low-RDS(ON) power MOSFETs. The evaluation board provides a ready-to-use platform that demonstrates the controller's dual-supply architecture: a main VIN rail powers the switching stage while a separate 5V VCC rail biases the controller, minimizing driver losses and improving overall efficiency. A switching regulator controller is an integrated circuit that uses PWM control and external or internal power switches to step a higher DC input voltage down to a lower DC output voltage with high efficiency. Switching regulators are preferred over linear regulators when the input-to-output voltage differential is large or when output currents exceed roughly 0.5 A, because they dissipate far less power. The SP7650 belongs specifically to the synchronous buck controller family, characterized by an integrated high-side switch and low-side synchronous rectifier that eliminate the need for an external Schottky diode, further reducing conduction loss and PCB footprint. Key specifications of the SP7650EB include an evaluation platform input range of 2.5V to 28V, a configurable output down to 0.8V, continuous load capability of 3A, a fixed switching frequency of 300 kHz, and built-in UVLO detection on both VCC and VIN rails. The board showcases the controller's soft-start, current-mode control loop, and synchronized rectification topology. Its small total solution size, achieved through the 300 kHz switching frequency, allows engineers to use compact inductors and ceramic output capacitors in their end design. Typical applications include distributed power bus conversion from 12V or 24V backplanes, point-of-load regulation for FPGAs, ASICs, and DSPs, telecom base-station intermediate rails, and industrial control supplies that must operate reliably across wide input transients. The dual-supply topology is particularly attractive in systems where a 5V housekeeping rail is already present, allowing the controller to operate from that low-voltage supply while the switching stage handles the full 28V input span. When designing with this evaluation board, ensure that adequate input bulk capacitance is placed near the VIN pins and that the feedback resistor divider is selected with 1% tolerance or better to maintain tight output voltage regulation. The fixed 300 kHz operation simplifies EMI filter design but requires attention to switching-node layout to minimize radiated noise in noise-sensitive systems.
SPSA068 - Automotive PMIC with Buck and Precise Voltage Reference | STMicroelectronics
The SPSA068 is an automotive-grade Power Management IC (PMIC) from STMicroelectronics, integrating a synchronous current-mode buck voltage regulator with integrated high-side and low-side power MOSFETs, along with a precise 1% accurate voltage reference. It is designed for microcontroller (MCU) applications in car passenger compartments that require functional safety. The device is available in a compact 32-pin VFQFN (5x5 mm) package, enabling space-constrained automotive PCB designs. A PMIC (Power Management Integrated Circuit) is a class of integrated circuits that manage power requirements of a host system, typically including voltage regulators, references, and supervisory functions. In the hierarchy of power management, a PMIC sits above individual regulators, integrating multiple power functions into a single device to reduce board space and improve reliability. The SPSA068 specifically combines a buck converter (a step-down switching regulator) with a precise voltage reference, a window watchdog, a reset output, and an SPI interface, making it a complete power solution for automotive MCUs. Key features of the SPSA068 include AEC-Q100 qualification, a pre-SMPS buck regulator adjustable via NVM to 5.0 V, 3.3 V, or 1.2 V at load currents of 0.5 A and 1.0 A, with switching frequencies of 0.4/2.4 MHz. It also provides a 1% accurate reference voltage, a window watchdog, a reset output, and an SPI bus for configuration. The low-power mode (LPM) reduces quiescent current to 50 μA typical under light-load conditions, making it suitable for always-on automotive systems. Technically, the SPSA068 uses a synchronous current-mode buck architecture with integrated power MOSFETs, which improves efficiency and reduces external component count. The internal programmable memory (NVM) allows selection of output voltages and switching frequencies, providing design flexibility. The precise voltage reference is based on a bandgap architecture, ensuring stable operation over temperature and supply variations. The device also includes protection features such as thermal shutdown and overcurrent protection, enhancing system reliability. Typical applications include automotive body control modules, engine control units (ECUs), and infotainment systems, where a reliable and efficient power supply for MCUs is critical. The SPSA068 is also used in functional safety applications, as it supports the requirements of ISO 26262 with its window watchdog and reset output. Its low quiescent current makes it ideal for battery-powered automotive systems that require minimal power draw when the vehicle is off. When designing with the SPSA068, it is important to properly configure the NVM settings for the desired output voltage and switching frequency. The SPI interface allows dynamic configuration, but the default settings should be verified against the application requirements. Additionally, adequate input and output capacitance is required for stable operation of the buck converter, and the PCB layout should minimize parasitic inductance in the power path.
SR087SG-G - Off-Line Inductorless Switching Regulator | Microchip
The Microchip Technology SR087SG-G is an adjustable off-line inductorless switching regulator that operates directly from a rectified AC line, delivering a 5.0V main output plus an adjustable auxiliary output up to 50V, with a combined output current of up to 100 mA in an 8-pin SOIC with exposed pad (SOIC-8-EP) package. An off-line inductorless switching regulator is a type of AC/DC converter, part of the broader power management IC (PMIC) hierarchy, that produces a regulated low-voltage DC rail directly from the rectified AC mains without using magnetic components such as transformers or inductors. This topology sits between conventional linear regulators and flyback converters: it achieves galvanic-unisolated, magnet-free regulation, dramatically simplifying the bill of materials for low-power mains-powered products. Key features of the SR087SG-G include efficient operation without magnetics, elimination of high-voltage capacitors from the power path, an adjustable main output voltage, a 5.0V internal regulator supporting up to 100 mA combined output current, and a single bill of materials that covers both 120VAC and 230VAC line inputs. Built-in soft start limits inrush current at power-up, and standby consumption is less than 200 mW, helping designs meet low no-load power requirements. Architecturally, the SR087 (originally a Supertex part, now under Microchip Technology) regulates by controlling charge transferred to an external capacitor, switching only when the storage capacitor requires replenishment. This charge-transfer control keeps switching losses low and allows the external components to remain small, low-voltage parts rather than bulky magnetics or 400V film capacitors. Typical applications include home appliances with low-power standby supplies, white goods control panels, smart meters and energy monitoring nodes, LED lighting control interfaces, and industrial auxiliary power for microcontrollers such as PIC MCUs that need a clean 5V rail from the AC line. A key design consideration is thermal and energy-budget sizing: because the topology is inductorless and unisolated, the entire circuit floats at mains potential, and the 100 mA combined output budget must account for both the 5V rail and the adjustable output. Never probe or connect user-accessible circuitry without isolation. This page synthesizes distributor pricing, family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
SR5E1E3 - 5V 1A LDO Voltage Regulator | STMicroelectronics
The SR5E1E3 is a low-dropout (LDO) linear voltage regulator from STMicroelectronics, designed to deliver a fixed 5V output with a maximum output current of 1A. It operates with an input voltage range of 6V to 26V, making it suitable for a variety of industrial and consumer applications. The device is available in a TO-252 (DPAK) package, which provides excellent thermal performance for moderate power dissipation. An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage. Unlike standard linear regulators, LDOs can operate with a smaller input-to-output voltage differential, reducing power dissipation and improving efficiency in battery-powered or low-headroom applications. LDOs are a subset of linear regulators, which in turn are a type of voltage regulator, a fundamental building block in power management ICs. They are widely used to provide clean, low-noise supply rails for analog, digital, and RF circuits. Key features of the SR5E1E3 include a fixed 5V output, a maximum output current of 1A, and a dropout voltage of 500mV at full load. The device also offers internal current limiting and thermal shutdown protection, ensuring safe operation under fault conditions. The TO-252 package has a thermal resistance of 62°C/W, allowing it to dissipate up to 1.6W at 25°C ambient without external heatsinking. The operating temperature range is -40°C to +125°C, making it suitable for harsh environments. The SR5E1E3 uses a PNP pass transistor architecture, which provides low dropout voltage and stable operation. The internal bandgap reference ensures accurate output voltage regulation across temperature and load variations. The device is designed for simplicity, requiring only input and output capacitors for stable operation. The fixed output voltage eliminates the need for external resistor dividers, reducing component count and board space. Typical applications include powering microcontrollers, sensors, and small logic circuits in industrial control systems, automotive electronics, and consumer appliances. The wide input voltage range allows it to be used in 12V and 24V bus systems, providing a regulated 5V rail for digital circuitry. The low dropout voltage ensures efficient operation even when the input voltage is close to 5V, such as in battery-powered devices. When designing with the SR5E1E3, ensure adequate input and output capacitance (typically 10µF) to maintain stability and transient response. The thermal pad of the TO-252 package should be connected to a large copper area on the PCB to enhance heat dissipation. For high-current applications, verify that the junction temperature remains within the safe operating range by calculating power dissipation and thermal resistance.
ST1S03PUR - 1.5A 1.5MHz Step-Down DC-DC Converter | STMicro
The STMicroelectronics ST1S03PUR is a 1.5 A, 1.5 MHz adjustable step-down switching regulator housed in a 6-pin DFN (3x3 mm) package with exposed pad. It delivers up to 1.5 A of output current over an input voltage range of 3 V to 16 V with a 2 percent DC output voltage tolerance and internal soft-start. The ST1S03PUR uses current-mode PWM control at a fixed 1.5 MHz switching frequency, allowing the use of tiny surface-mount inductors and ceramic output capacitors while sustaining typical efficiencies greater than 70 percent across operating conditions. A step-down switching regulator (buck converter) is a DC-DC converter that produces a lower DC output voltage from a higher DC input voltage by rapidly switching an internal MOSFET and storing energy in an inductor. Within the broader power management hierarchy, the ST1S03PUR sits in the DC-DC converter family (buck topology), which belongs to the voltage regulator category and ultimately the power management IC class used in virtually every battery- and bus-powered electronic system. Key features of the ST1S03PUR include a 1.5 MHz switching frequency that enables sub-2 mm inductor solutions, internal soft-start that limits inrush current and provides a 50 to 100 microsecond power-on delay, 2 percent DC output voltage tolerance, current-mode PWM control for cycle-by-cycle current limiting, and not-switching quiescent current optimization that preserves battery life. The exposed thermal pad on the DFN-6 (3x3) package keeps junction temperature in check at full 1.5 A load. The architecture combines a P-channel power MOSFET, a precision reference, an error amplifier, and a current-sense comparator inside a single die. The current-mode loop simplifies compensation with a single resistor-capacitor network and provides inherent line rejection, making the device robust against input voltage transients on 12 V buses. The 1.5 MHz switching frequency is well above the AM band, simplifying EMI filter design in audio and consumer products. Typical applications include HDD digital core supplies, point-of-load conversion in 12 V distributed systems, USB-powered devices, and portable battery-powered equipment where the small DFN-6 footprint and high switching frequency enable compact PCB layouts. According to the STMicroelectronics ST1S03 datasheet, the device is optimized to replace high-current linear regulators when power dissipation would otherwise cause excessive heating. When designing with the ST1S03PUR, choose an inductor with low DCR to minimize conduction loss, and place the input ceramic bypass capacitor as close as possible to the VIN and GND pins. Ensure that the feedback resistor divider sets VOUT between 0.8 V and approximately VIN times 0.85, and verify that the maximum rated junction temperature is not exceeded under worst-case VIN and IOUT conditions. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.
ST1S09PUR - 2A 1.5MHz Sync Buck DC-DC Converter | STMicroelectronics
The STMicroelectronics ST1S09PUR is a 2 A, 1.5 MHz PWM step-down switching regulator with synchronous rectification, housed in a 6-pin DFN (VDFN Exposed Pad) package optimized for powering low-voltage point-of-load applications. It operates over an input voltage range of 2.7 V to 6 V and delivers an adjustable output from 0.8 V up to 5 V at up to 2 A continuous load, making it suitable for 3.3 V and 5 V bus systems that must produce lower core or I/O voltages with high efficiency. A step-down (buck) DC-DC converter is a switched-mode power supply topology that uses an internal MOSFET switch, an inductor, and a capacitor network to convert a higher DC input voltage into a lower DC output voltage. Unlike a linear regulator, a buck converter achieves high efficiency (typically 90-95%) by rapidly switching the input and filtering the resulting waveform, rather than continuously dissipating excess voltage as heat. Synchronous rectification replaces the conventional Schottky diode with a low-RDS(on) MOSFET, which further reduces conduction losses and improves thermal performance at heavy loads. Within the broader taxonomy, the ST1S09 belongs to the DC-DC converter family, which itself sits inside the voltage regulators and power management IC categories commonly used in modern electronics. Key features of the ST1S09PUR include 1.5 MHz fixed-frequency current-mode PWM control, internal power MOSFETs (high-side and low-side synchronous switch), internal soft-start, current limiting, and thermal shutdown protection. The 1.5 MHz switching frequency allows the use of very small inductors and ceramic capacitors, enabling compact point-of-load designs on densely populated PCBs. The 6-lead DFN package includes an exposed thermal pad that provides a low thermal resistance path to the PCB copper, supporting continuous 2 A output without external heatsinking in properly laid-out boards. Architecturally, the device uses peak current-mode control with internal compensation, providing cycle-by-cycle current limit, simple external component selection, and good transient response. The internal synchronous MOSFET reduces external part count to just an inductor, input bypass capacitor, output filter capacitor, and feedback resistor divider. According to the STMicroelectronics datasheet, the device includes an enable/shutdown input that allows the regulator to be placed in a low-quiescent state when not needed, supporting battery-powered applications. Typical applications for the ST1S09PUR include powering DSPs, FPGAs, microcontrollers, and ASIC core or I/O rails from a 3.3 V or 5 V system rail, USB-powered devices, portable and battery-powered equipment, hard-disk drive power, and point-of-load regulation in distributed power architectures. The wide 2.7 V to 6 V input range also makes it compatible with single-cell Li-Ion battery systems (2.7 V to 4.2 V) and 5 V USB rails (4.5 V to 5.5 V under USB specification). When designing with the ST1S09PUR, place input and output capacitors close to the IC, use a low-ESR ceramic output capacitor of at least 22 uF, and lay out the exposed pad on a continuous ground copper pour of at least 1 cm² to dissipate 2 A of continuous current without overheating. Verify the inductor saturation current rating exceeds the peak switch current limit by at least 20% margin for reliable operation. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical thermal and layout design notes not found in the manufacturer datasheet, helping engineers select, source, and implement the ST1S09PUR in compact high-efficiency power designs.
ST1S10PHR - 3A, 18V Synchronous Step-Down Converter | STMicroelectronics
The STMicroelectronics ST1S10PHR is a 3 A high-efficiency monolithic synchronous step-down switching regulator housed in an 8-pin PowerSO-8 (HSOP-8) exposed-pad package. It operates from a 2.5 V to 18 V input range, delivers an adjustable output from 0.8 V up to roughly 0.85 x VIN, and switches at a fixed 900 kHz (or 400 kHz to 1.2 MHz when externally synchronized via the SYNC pin). Current-mode PWM control with internal high-side and low-side MOSFETs achieves up to 90 % typical efficiency at full load, making the device well suited to space-constrained point-of-load designs. What is a synchronous step-down (buck) DC-DC converter? A buck converter is a switched-mode power supply topology that converts a higher DC input voltage to a lower DC output voltage by periodically storing energy in an inductor and releasing it to the load through a smoothing capacitor. The 'synchronous' qualifier means the free-wheeling diode is replaced by a second MOSFET, which dramatically reduces conduction losses at high current. Buck converters belong to the broader power management IC hierarchy: switching regulator -> DC-DC converter -> PMIC -> semiconductor. They are preferred over linear regulators whenever VIN is more than a few hundred millivolts above VOUT, because efficiency can exceed 90 % versus the VIN/VOUT ratio limit of an LDO. Key specifications of the ST1S10PHR include 3 A continuous output current, 2.5 V to 18 V input voltage range, 0.8 V minimum feedback voltage, and a typical quiescent current of 1.5 mA. The fixed 900 kHz switching frequency allows the use of a small 4.7 µH to 10 µH inductor and low-ESR ceramic output capacitors, minimizing the total solution footprint to roughly 100 mm². Internal soft-start, cycle-by-cycle current limit, and thermal shutdown protect the device and downstream components during fault and startup events. Architecturally, the device uses peak current-mode control with an internal compensation network, which simplifies external loop design and provides fast transient response to load steps. The integrated 80 mΩ high-side and 60 mΩ low-side MOSFETs, combined with a thermally efficient exposed-pad PowerSO-8 package, allow sustained 3 A operation without an external heatsink at moderate ambient temperatures. The SYNC/INH pin enables frequency synchronization to an external clock for noise-sensitive multi-rail systems. Typical applications include point-of-load regulation for FPGAs, DSPs, and microprocessors from a 5 V or 12 V bus, distributed power architectures in networking and telecom equipment, set-top boxes, LCD displays, and industrial control boards. The wide VIN range also makes it suitable for battery-powered portable systems running from 2-cell lithium packs. When designing with the ST1S10PHR, place input ceramic capacitors as close as possible to the VIN and PGND pins to minimize switching noise, and solder the exposed pad to a copper area of at least 50 mm² for thermal dissipation. Use 1 % tolerance resistors in the feedback divider to maintain output voltage accuracy, and verify inductor saturation current exceeds the peak switch current limit. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select, source, and implement the ST1S10PHR with confidence.
ST1S12GR - 3A, 18V Synchronous Step-Down Regulator | STMicroelectronics
The ST1S12GR is a high-efficiency synchronous step-down (buck) DC-DC converter from STMicroelectronics, designed to deliver up to 3A of continuous output current from an input voltage range of 4.5V to 18V. Housed in a compact SOT-23-6 package, this regulator integrates both high-side and low-side MOSFETs, eliminating the need for external Schottky diodes and simplifying PCB layout. The device operates at a fixed 1.5MHz switching frequency, allowing the use of small, low-cost inductors and capacitors, which is ideal for space-constrained applications. A synchronous buck converter is a type of DC-DC step-down regulator that uses two active switches (typically MOSFETs) instead of a diode for the low-side element, improving efficiency by reducing conduction losses. In the power management hierarchy, a synchronous buck converter falls under DC-DC converters, which are a subset of voltage regulators, which in turn are part of power management ICs. This architecture is essential in battery-powered and high-current systems where thermal performance and efficiency are critical. Key features of the ST1S12GR include a 3A output current capability, an adjustable output voltage from 0.8V to VIN, and a high efficiency of up to 95% at light loads. The device also features internal soft-start to limit inrush current, overcurrent protection, and thermal shutdown. The 1.5MHz switching frequency enables a compact solution footprint, and the SOT-23-6 package (also known as TSOT-6) is widely used in portable electronics. Technically, the ST1S12GR employs a current-mode control architecture, providing fast transient response and stable operation with ceramic output capacitors. The integrated MOSFETs have low RDS(on), minimizing conduction losses, while the synchronous rectification improves efficiency at heavy loads. The device supports 100% duty cycle operation, allowing the output to be very close to the input voltage, which is beneficial for battery-powered applications where the input voltage can drop near the output. Typical applications include point-of-load (POL) converters for FPGAs, DSPs, and microcontrollers, as well as power supplies for set-top boxes, networking equipment, and industrial control systems. The wide input range also makes it suitable for 12V and 24V industrial bus systems, providing a regulated 3.3V or 5V rail. When designing with the ST1S12GR, ensure proper input and output capacitor selection to maintain stability and low output ripple. The inductor value should be chosen based on the desired ripple current, typically 30% of the maximum load current. Place the input capacitor close to the VIN pin to minimize parasitic inductance, and use a solid ground plane for thermal management.
ST1S14PHR - 3A 36V Step-Down Switching Regulator | STMicroelectronics
The ST1S14PHR is a step-down switching regulator from STMicroelectronics, designed to deliver up to 3A of continuous output current from a wide input voltage range of 4.5V to 36V. Housed in a compact PowerSO-8 package, this regulator integrates a high-side power MOSFET and provides a fixed 250kHz switching frequency, making it suitable for a variety of industrial and automotive power supply applications. A step-down switching regulator, also known as a buck converter, is a type of DC-DC converter that efficiently reduces a higher input voltage to a lower output voltage. Unlike linear regulators, which dissipate excess power as heat, switching regulators use an inductor and a switch to transfer energy in discrete packets, achieving high efficiency, especially when the input-to-output voltage difference is large. The ST1S14PHR belongs to the family of voltage regulators, specifically switching regulators, which are essential components in power management systems for converting and stabilizing voltages across electronic devices. Key features of the ST1S14PHR include a wide input voltage range of 4.5V to 36V, an adjustable output voltage from 1.2V to 36V, and a maximum output current of 3A. The device offers a high efficiency of up to 90%, a low quiescent current of 2.5mA, and a switching frequency of 250kHz. It also includes internal compensation, a soft-start function, and a thermal shutdown protection, ensuring reliable operation in demanding environments. The ST1S14PHR utilizes a current-mode control architecture, which provides fast transient response and simplifies loop compensation. The integrated high-side MOSFET reduces external component count, while the internal compensation network eliminates the need for external compensation components. The device operates over a junction temperature range of -40°C to +150°C, making it suitable for automotive and industrial applications where temperature extremes are common. Typical applications include point-of-load (POL) converters, distributed power systems, industrial control systems, and automotive infotainment and body electronics. The wide input voltage range allows the ST1S14PHR to operate directly from 12V or 24V supply rails, while the high output current capability supports powering microprocessors, FPGAs, and other digital loads. When designing with the ST1S14PHR, ensure proper PCB layout with short, low-inductance paths for the power stage. The exposed pad on the PowerSO-8 package should be soldered to a large copper area for effective heat dissipation. Additionally, select an inductor with a saturation current rating above the peak switch current to avoid core saturation and ensure stable operation.
ST1S40PUR - 3A, 4V to 18V Step-Down Converter | STMicroelectronics
The ST1S40PUR is a high-efficiency, monolithic step-down switching regulator from STMicroelectronics, designed to deliver up to 3A of continuous output current from an input voltage range of 4V to 18V. Housed in a compact 6-pin DFN (DFN6) package with an exposed pad, this device integrates a low-side MOSFET and synchronous rectification to achieve efficiencies up to 90% in typical applications. The output voltage is adjustable from 0.8V to VIN, set by an external resistor divider, making it suitable for a wide range of point-of-load (POL) applications. A step-down (buck) converter is a type of DC-DC switching regulator that steps down an input voltage to a lower output voltage with high efficiency. Unlike linear regulators, which dissipate excess power as heat, buck converters use an inductor and switching elements to transfer energy in discrete packets, achieving efficiencies often above 85%. In the power management hierarchy, a buck converter is a type of switching regulator, which is a subset of voltage regulators, which in turn are part of power management ICs (PMICs) used in virtually all electronic systems to provide stable, efficient power rails. Key features of the ST1S40PUR include a fixed 1.5MHz switching frequency, which allows the use of small external components (inductor and capacitors), reducing PCB footprint. The device offers a low quiescent current of 1.5mA in light-load operation, and a shutdown mode that reduces current consumption to less than 1uA. Protection features include overcurrent protection (OCP), thermal shutdown, and under-voltage lockout (UVLO). The DFN6 package (3mm x 3mm) has a thermal resistance of 45°C/W, enabling efficient heat dissipation in compact designs. The ST1S40PUR uses a current-mode control architecture with internal compensation, simplifying the design process. The high switching frequency minimizes the size of the output inductor (typically 2.2uH to 4.7uH) and output capacitors, making it ideal for space-constrained applications. The device also features a soft-start function to limit inrush current during startup, and an enable pin for power sequencing. Typical applications include distributed power systems, set-top boxes, LCD TVs, networking equipment, and industrial control systems. The wide input range and high output current make it suitable for powering FPGAs, DSPs, and microprocessors from 12V or 5V rails. In set-top boxes, the ST1S40PUR efficiently converts a 12V input to a 3.3V or 1.8V rail for core logic, reducing heat and improving reliability. When designing with the ST1S40PUR, ensure proper PCB layout with short, wide traces for high-current paths and a solid ground plane. Place the input capacitor close to the VIN pin and the output inductor close to the SW pin to minimize parasitic inductance. The exposed pad should be soldered to a large copper area for thermal management.
ST1S41PUR - 4A 18V Sync Step-Down DC-DC | STMicroelectronics
The STMicroelectronics ST1S41PUR is a 4 A internally compensated, 850 kHz fixed-frequency PWM synchronous step-down (buck) DC-DC converter housed in an 8-lead DFN (3x3 mm) exposed-pad package. It operates from a 4.0 V to 18 V input rail and regulates an output voltage as low as 0.8 V and up to VIN, integrating a 95 mΩ high-side switch and a 69 mΩ synchronous rectifier to deliver high efficiency at low output voltages. The ST1S41PUR uses peak-current-mode control with internal compensation, achieving a very compact solution with a minimum external component count. A buck (step-down) DC-DC converter is a switching voltage regulator that reduces a higher DC input voltage to a lower DC output voltage by rapidly switching an inductor and rectifying the resulting waveform. Unlike linear regulators that dissipate the VIN-VOUT difference as heat, buck converters achieve 90%+ efficiency even at large step-down ratios by storing energy in an inductor during the switch-on phase and releasing it during the switch-off phase. In the power management hierarchy, a buck converter is a DC-DC converter, which is a subset of voltage regulators, which belong to the broader power management IC category. Buck regulators are the workhorse of point-of-load conversion in modern digital systems. Key features of the ST1S41PUR include 90% peak efficiency, internal soft-start with cycle-by-cycle current limiting, overcurrent protection, and thermal shutdown. The 850 kHz nominal switching frequency (programmable from 700 kHz to 1 MHz) permits the use of small inductors and ceramic output capacitors, enabling a sub-100 mm² total solution footprint. The exposed thermal pad on the DFN-8 package provides a low thermal resistance path for dissipating switch losses, supporting full 4 A continuous output without external heatsinking in well-designed layouts. Typical applications include point-of-load regulation for FPGAs, microcontrollers, and ASICs, 12 V bus-powered distributed systems, industrial control boards, and consumer electronics requiring high step-down ratios. The 4 V minimum input also makes it suitable for USB Type-C PD and 5 V supply rails. When designing, choose an inductor of approximately 4.7 µH for most VIN/VOUT combinations to maintain continuous-conduction mode. Place the input ceramic bypass capacitor directly adjacent to the PVIN pin and the exposed pad to a large ground copper pour to extract heat. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.