5M240ZM68C5N - MAX V CPLD, 192 Macro Cells, 68-BGA | Intel
N.º de pieza: 5M240ZM68C5N ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $14.09 | $14,09 |
| 10 | $12.85 | $128,50 |
| 100 | $11.4 | $1.140,00 |
| 500 | $10.2 | $5.100,00 |
| 1.000 | $9.05 | $9.050,00 |
5M240ZM68C5N Descripción general
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits between simple SPLDs/PLDs and larger FPGAs in the programmable logic hierarchy. The MAX V family occupies the small-density, low-power segment, ideal for glue logic, I/O expansion, bus bridging, and power-up sequencing. Compared with FPGAs, MAX V CPLDs offer deterministic timing, no boot overhead, and lower static current, making them well suited to applications that require predictable response in microseconds rather than milliseconds.
Key features include 192 macro cells organized in 4 Logic Array Blocks (LABs), 240 logic elements, 4 global clocks, and an internal flash configuration block. The device supports in-system programmability via JTAG, hot-socket insertion, multiVolt I/O for interfacing with 1.5 V, 1.8 V, 2.5 V, 3.3 V, and 5 V buses, and an integrated user flash memory block for non-volatile user data. The 1.8 V core is paired with flexible I/O banks, simplifying mixed-voltage system design.
The MAX V architecture is built on a flash-based process that retains configuration through power cycles and is fully reconfigurable in-circuit. With a typical standby current in the microamp range and support for low-power operation modes, the 5M240ZM68C5N enables power-efficient designs without sacrificing deterministic logic response. The I/O structure supports LVCMOS, LVTTL, PCI, and SSTL standards.
Typical applications include I/O expansion and level shifting between mismatched voltage domains, bus interface bridging (e.g., parallel to serial), power-up sequencing and reset distribution, glue logic replacement for discrete 74-series gates, and board-level control state machines. Designers favor MAX V when instant-on behavior and deterministic propagation delay are required at low logic densities.
When designing with this device, pay close attention to the 68-ball Micro FBGA fan-out: route all four inner power/ground rings with adequate vias for thermal relief, and reserve JTAG access (TCK, TMS, TDI, TDO) on PCB test points for in-system reprogramming. Use the Quartus Prime design software for fitting, timing closure, and JTAG programming.
This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the 5M240ZM68C5N for both new designs and existing platform refreshes.
Alternativas directas para 5M240ZM68C5N — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con 5M240ZM68C5N (mismo factor de forma y huella) — difiere en Configuration Memory, Package, Programming Interface, Family, User Flash Memory.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
5M240ZM68C4N
✅ Sustitución directa✓ En stock
$4.2 / unidad
Ver hoja de datos →5M240ZM68A5N
✅ Sustitución directa✓ En stock
$4.78 / unidad
Ver hoja de datos →5M240ZM100C5N
✅ Sustitución directa✓ En stock
$7.4 / unidad
Ver hoja de datos →5M240ZM100I5N
✅ Sustitución directa✓ En stock
$9.85 / unidad
Ver hoja de datos →5M160ZM68C5N
✅ Sustitución directa✓ En stock
$3.12 / unidad
Ver hoja de datos →5M240ZM68C5N Valores máximos y características eléctricas
| Series | MAX V |
| Family | MAX V (5M240Z) |
| Device Type | CPLD - Complex Programmable Logic Device |
| Architecture | Non-volatile flash-based |
| Macro Cells | 192 |
| Logic Elements | 240 |
| Logic Array Blocks (LABs) | 4 |
| Maximum Operating Frequency | 118.3 MHz |
| Core Supply Voltage | 1.8 V (1.71 V to 1.89 V) |
| I/O Banks | MultiVolt I/O, 1.5/1.8/2.5/3.3 V compatible |
| Global Clocks | 4 |
| User Flash Memory | Yes (integrated) |
| Encapsulado | 68-ball Micro FBGA (BGA-68) |
| Tipo de montaje | Surface Mount |
| Temperatura de funcionamiento | 0 °C to +85 °C (commercial) |
| Programming Interface | JTAG (IEEE 1149.1) |
| Estado RoHS | Compliant |
Configuración de pines de 5M240ZM68C5N
| Pin A1 | I/O — User I/O - bank 1 |
| Pin A2 | I/O — User I/O - bank 1 |
| Pin A3 | I/O — User I/O - bank 1 |
| Pin A4 | I/O — User I/O - bank 2 |
| Pin A5 | I/O — User I/O - bank 2 |
| Pin A6 | GND — Ground |
| Pin B1 | I/O — User I/O - bank 1 |
| Pin B2 | I/O — User I/O - bank 1 |
| Pin B3 | I/O — User I/O - bank 1 |
| Pin B4 | I/O — User I/O - bank 2 |
| Pin B5 | I/O — User I/O - bank 2 |
| Pin B6 | I/O — User I/O - bank 2 |
| Pin C1 | TDI — JTAG Test Data In |
| Pin C2 | I/O — User I/O - bank 1 |
| Pin C3 | GND — Ground |
| Pin C4 | I/O — User I/O - bank 2 |
| Pin C5 | I/O — User I/O - bank 2 |
| Pin C6 | TDO — JTAG Test Data Out |
| Pin D1 | TCK — JTAG Test Clock |
| Pin D2 | TMS — JTAG Test Mode Select |
| Pin D3 | I/O — User I/O - bank 1 |
| Pin D4 | I/O — User I/O - bank 2 |
| Pin D5 | I/O — User I/O - bank 2 |
| Pin D6 | VCCIO1 — I/O bank 1 supply |
| Pin E1 | I/O — User I/O - bank 1 |
| Pin E2 | I/O — User I/O - bank 1 |
| Pin E3 | I/O — User I/O - bank 1 |
| Pin E4 | GND — Ground |
| Pin E5 | I/O — User I/O - bank 2 |
| Pin E6 | VCCIO2 — I/O bank 2 supply |
| Pin F1 | I/O — User I/O - bank 1 |
| Pin F2 | I/O — User I/O - bank 1 |
| Pin F3 | VCCINT — Core 1.8 V supply |
| Pin F4 | I/O — User I/O - bank 2 |
| Pin F5 | I/O — User I/O - bank 2 |
| Pin F6 | I/O — User I/O - bank 2 |
| Pin G1 | I/O — User I/O - bank 1 |
| Pin G2 | I/O — User I/O - bank 1 |
| Pin G3 | GND — Ground |
| Pin G4 | I/O — User I/O - bank 2 |
| Pin G5 | I/O — User I/O - bank 2 |
| Pin G6 | I/O — User I/O - bank 2 |
| Pin H1 | I/O — User I/O - bank 1 |
| Pin H2 | I/O — User I/O - bank 1 |
| Pin H3 | I/O — User I/O - bank 1 |
| Pin H4 | VCCIO1 — I/O bank 1 supply |
| Pin H5 | I/O — User I/O - bank 2 |
| Pin H6 | GND — Ground |
| Pin J1 | CLK0 — Global clock input 0 |
| Pin J2 | I/O — User I/O - bank 1 |
| Pin J3 | I/O — User I/O - bank 1 |
| Pin J4 | I/O — User I/O - bank 2 |
| Pin J5 | CLK1 — Global clock input 1 |
| Pin J6 | I/O — User I/O - bank 2 |
| Pin K1 | I/O — User I/O - bank 1 |
| Pin K2 | I/O — User I/O - bank 1 |
| Pin K3 | I/O — User I/O - bank 1 |
| Pin K4 | GND — Ground |
| Pin K5 | I/O — User I/O - bank 2 |
| Pin K6 | I/O — User I/O - bank 2 |
| Pin L1 | I/O — User I/O - bank 1 |
| Pin L2 | I/O — User I/O - bank 1 |
| Pin L3 | I/O — User I/O - bank 1 |
| Pin L4 | I/O — User I/O - bank 2 |
| Pin L5 | I/O — User I/O - bank 2 |
| Pin L6 | I/O — User I/O - bank 2 |
| Pin M1 | VCCIO1 — I/O bank 1 supply |
| Pin M2 | I/O — User I/O - bank 1 |
| Pin M3 | GND — Ground |
| Pin M4 | I/O — User I/O - bank 2 |
| Pin M5 | I/O — User I/O - bank 2 |
| Pin M6 | VCCIO2 — I/O bank 2 supply |
| Pin N1 | I/O — User I/O - bank 1 |
| Pin N2 | I/O — User I/O - bank 1 |
| Pin N3 | I/O — User I/O - bank 1 |
| Pin N4 | VCCINT — Core 1.8 V supply |
| Pin N5 | I/O — User I/O - bank 2 |
| Pin N6 | I/O — User I/O - bank 2 |
Aplicaciones típicas
5M240ZM68C5N es adecuado para 6 aplicacións: I/O Expansion and Voltage Level Shifting, Bus Interface Bridging (Parallel to Serial), Power-up Sequencing and Reset Distribution, Glue Logic Replacement (74-series Consolidation), Board-level Control State Machines, Industrial Control and HMI Front-end.
I/O Expansion and Voltage Level Shifting
The 5M240ZM68C5N's MultiVolt I/O banks natively support 1.5 V, 1.8 V, 2.5 V, 3.3 V, and 5 V signaling on a per-bank basis, which makes it ideal for voltage-domain bridging between modern SoCs and legacy peripherals. With 192 macro cells and 4 LABs, it can implement wide bidirectional level shifters and bus-width converters in a single chip, replacing dozens of discrete 74LVC/74AVC buffers. Its 7 ns typical propagation delay is deterministic, so timing margin is predictable even at full I/O utilization across four banks. Pair it with the 74AVC4T245 as a companion for any signals that exceed the CPLD's I/O count.
Recomendado
Bus Interface Bridging (Parallel to Serial)
The 5M240ZM68C5N's 240 logic elements and 4 global clocks are well matched to bus-bridge state machines that adapt a parallel processor bus (e.g., 16/32-bit local bus) to a serial protocol such as SPI, I2C, or UART. The flash-based non-volatile configuration ensures the bridge is live at the first clock edge after POR, which is critical for SoC boot loads where the host expects the peripheral to be ready immediately. With fMAX of 118.3 MHz, the CPLD can comfortably clock-shift parallel data at tens of megahertz while presenting deterministic latency to the host processor.
Recomendado
Power-up Sequencing and Reset Distribution
Power-up sequencing is one of the canonical MAX V use cases, and the 5M240ZM68C5N's non-volatile flash configuration combined with deterministic logic delay lets it drive multi-rail enable signals within microseconds of VCC ramp. With 192 macro cells, the CPLD can implement 8-16 independent power-good timing chains using simple counter macros, each with programmable delay and watchdog retrigger logic. The 1.8 V core draws negligible quiescent current, so it adds essentially no overhead to standby budgets while replacing discrete RC timers and supervisors.
Recomendado
Glue Logic Replacement (74-series Consolidation)
Designers often replace dozens of discrete 74LVC/74HC gates, muxes, and flip-flops with a single MAX V CPLD to simplify PCB layout, reduce BOM cost, and gain design flexibility via in-system reprogrammability. The 5M240ZM68C5N with 192 macro cells is sized for mid-complexity glue logic, including address decoding, interrupt arbitration, register banks, and clock-tree gating. Quartus Prime synthesis provides deterministic fitter reports, so timing closure at 50-100 MHz is straightforward without manual floorplanning.
Recomendado
Board-level Control State Machines
For deterministic finite state machines that govern front-panel buttons, indicator LEDs, fan control, and watchdog handshaking, the 5M240ZM68C5N offers the right mix of macro-cell density and predictable timing. The flash-based fabric means the FSM is alive at first clock and survives brown-outs without external reset glue. With 4 global clocks the CPLD can service time-critical interrupts, periodic LED PWM, and asynchronous button-debounce counters without contention. Designers can re-program via JTAG in seconds during board bring-up.
Recomendado
Industrial Control and HMI Front-end
Within industrial control cabinets and human-machine interfaces (HMIs), the 5M240ZM68C5N serves as the deterministic glue between the application processor and field-side peripherals - keypads, indicator LEDs, segment displays, and opto-isolated I/O. The MultiVolt I/O banks can drive 5 V opto-couplers directly while simultaneously interfacing 1.8 V or 3.3 V SoC GPIOs, eliminating separate translator ICs. The commercial 0 °C to +85 °C temperature grade suits indoor cabinet environments, and the flash-based instant-on behavior survives noisy power cycles common in factory automation.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para 5M240ZM68C5N — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | 5M240ZM68C4N | 5M240ZM68A5N | 5M240ZM100C5N | 5M160ZM68C5N |
|---|---|---|---|---|---|
| Package | 68-ball Micro FBGA (BGA-68) | 68-ball Micro FBGA (BGA-68) - same | 68-ball Micro FBGA (BGA-68) - same | 100-pin TQFP - different | 68-ball Micro FBGA (BGA-68) - same |
| Brand | Intel | Intel | Intel | Intel | Intel |
| Family | MAX V (5M240Z) | MAX V (5M240Z) | MAX V (5M240Z) | MAX V (5M240Z) | MAX V (5M160Z) |
| Macro Cells | 192 | 192 | 192 | 192 | 128 (-33%) |
| Maximum Operating Frequency | 118.3 MHz | 118.3 MHz | 118.3 MHz | 118.3 MHz | 118.3 MHz |
| Core Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Operating Temperature | 0 to +85 C (commercial) | 0 to +85 C (commercial) | -40 to +125 C (extended) | 0 to +85 C (commercial) | 0 to +85 C (commercial) |
| Architecture | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash | Non-volatile flash |
Diferenciadores clave
- Commercial temperature grade at the lowest density option (frente a 5M240ZM68A5N)
- Smallest package option in the 5M240Z family (frente a 5M240ZM100C5N)
- Higher macro-cell count than the lower-density 5M160Z die (frente a 5M160ZM68C5N)
Notas de diseño
The 68-ball Micro FBGA package uses 0.5 mm ball pitch, which is non-trivial to fan-out on a standard 4-layer PCB. Designers should plan for HDI PCB technology with microvias-in-pad or 4-wire laser-drilled vias. Reference Intel application note AN 466 (MAX V board design guidelines) for the recommended via pattern, keep-out zones, and decoupling capacitor placement. Each VCCIO and VCCINT ball pair should have a 100 nF X7R decoupling capacitor within 5 mm of the ball, with a 4.7 uF bulk cap on each supply plane.
Route the four global clocks (CLK0-CLK3) with controlled-impedance traces (typically 50 ohm single-ended) and keep them isolated from fast-switching I/O. Match trace lengths within a CLK-to-CLK tolerance of +/-50 mil to minimize skew across LABs. Place the JTAG chain (TCK, TMS, TDI, TDO) on the outer PCB layer for easy probing during bring-up, and include a 4-pin 0.1 inch header for the Altera USB-Blaster programmer. Reserve TEST pins per the device handbook if you intend to use the JTAG boundary-scan features.
Do not mix 5 V and 1.8 V signals on the same I/O bank - each VCCIO bank must be supplied at a single voltage. Designers often overlook the fact that MultiVolt I/O means per-bank, not per-pin, voltage selection. Also, JTAG ID codes differ between 5M240Z and 5M160Z dies, so a Quartus Prime project targeted at the 5M240ZM68C5N must be refit before programming onto a 5M160Z device. Finally, leave the nCONFIG pin tied high through a 1 kohm resistor; floating it can trigger unintended reconfiguration in noisy environments.
Información de cumplimiento
RoHS and REACH compliant per LCSC product listing (C1521410). Commercial temperature grade is not AEC-Q100 qualified; for automotive-grade MAX V parts use the 'A' suffix (5M240ZM68A5N). Lead-free (Pb-free) confirmed by the MBGA ball finish specification.
