ADUM3154BRSZ-RL7 - SPI Digital Isolator 3750Vrms | Analog Devices
N.º de pieza: ADUM3154BRSZ-RL7 ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $6.5 | $6,50 |
| 10 | $5.85 | $58,50 |
| 100 | $5.2 | $520,00 |
| 500 | $4.68 | $2.340,00 |
| 1.000 | $4.16 | $4.160,00 |
ADUM3154BRSZ-RL7 Descripción general
A digital isolator is a component that provides galvanic isolation between two circuits while allowing digital signals to pass across the isolation barrier. It is used to protect sensitive electronics from high voltages, ground loops, and noise, and is essential in industrial, medical, and communication systems where safety and signal integrity are critical. Digital isolators are part of the broader category of isolation components, which also includes optocouplers and magnetic isolators.
Key features of the ADUM3154BRSZ-RL7 include a 3750Vrms isolation rating, 4 forward channels and 3 reverse channels, a data rate of 34 Mbps, and a common-mode transient immunity (CMTI) of 25 kV/µs. The device operates with a supply voltage range of 3.0V to 3.6V on VDD1 and 4.5V to 5.5V on VDD2, ensuring compatibility with standard logic levels. The low propagation delay and jitter make it ideal for high-speed SPI communication.
The ADUM3154BRSZ-RL7 uses iCoupler technology, which employs chip-scale transformers to transmit data across the isolation barrier. This technology offers advantages over optocouplers, including higher data rates, lower power consumption, and better reliability. The device also features a multiple-slave SPI configuration, allowing it to interface with up to four SPI slave devices without additional components.
Typical applications include isolated SPI interfaces in industrial automation, motor control, data acquisition systems, and medical equipment. The device is also suitable for use in communication systems where galvanic isolation is required to protect against voltage transients and ground potential differences.
When designing with this device, it is important to ensure proper PCB layout to minimize coupling across the isolation barrier. The datasheet recommends that any coupling that occurs should affect all pins equally on a given component side to prevent voltage differentials that could exceed absolute maximum ratings.
Alternativas directas para ADUM3154BRSZ-RL7 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con ADUM3154BRSZ-RL7 (mismo factor de forma y huella) — difiere en Technology, Number of Channels, Isolation Voltage, Package, RoHS Status.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
ADUM3154BRSZ
✅ Sustitución directa✓ En stock
$3.1 / unidad
Ver hoja de datos →ADUM3153BRSZ-RL7
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$3.1 / unidad
Ver hoja de datos →ADUM3151BRSZ-RL7
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$7.45 / unidad
Ver hoja de datos →ADUM3154ARIZ
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
ADUM3154BRIZ
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
ADUM3154BRSZ-RL7
✅ Sustitución directa✓ En stock
$4.16 / unidad
Ver hoja de datos →ADUM3154BRSZ-RL7 Especificaciones
| Isolation Voltage | 3750 Vrms |
| Number of Channels | 7 (4 forward, 3 reverse) |
| Velocidad de datos | 34 Mbps |
| Common-Mode Transient Immunity (CMTI) | 25 kV/µs |
| SPI Clock Rate | 17 MHz |
| Supply Voltage VDD1 | 3.0 V to 3.6 V |
| Supply Voltage VDD2 | 4.5 V to 5.5 V |
| Rango de temperatura de funcionamiento | -40°C to +125°C |
| Encapsulado | 20-SSOP (0.209", 5.30mm Width) |
| Tipo de montaje | Surface Mount |
| Technology | iCoupler |
| Number of Slave Devices Supported | 4 |
| Estado RoHS | Compliant |
Configuración de pines de ADUM3154BRSZ-RL7
| Pin 1 | VDD1 — Primary supply voltage (3.0V to 3.6V) |
| Pin 2 | GND1 — Primary ground |
| Pin 3 | CLK — SPI clock input |
| Pin 4 | MO/SI — Master out, slave in data |
| Pin 5 | MI/SO — Master in, slave out data |
| Pin 6 | SS1 — Slave select 1 |
| Pin 7 | SS2 — Slave select 2 |
| Pin 8 | SS3 — Slave select 3 |
| Pin 9 | SS4 — Slave select 4 |
| Pin 10 | GND1 — Primary ground |
| Pin 11 | VDD2 — Secondary supply voltage (4.5V to 5.5V) |
| Pin 12 | GND2 — Secondary ground |
| Pin 13 | CLK_ISO — Isolated SPI clock output |
| Pin 14 | MO/SI_ISO — Isolated master out, slave in data |
| Pin 15 | MI/SO_ISO — Isolated master in, slave out data |
| Pin 16 | SS1_ISO — Isolated slave select 1 |
| Pin 17 | SS2_ISO — Isolated slave select 2 |
| Pin 18 | SS3_ISO — Isolated slave select 3 |
| Pin 19 | SS4_ISO — Isolated slave select 4 |
| Pin 20 | GND2 — Secondary ground |
Aplicaciones típicas
ADUM3154BRSZ-RL7 es adecuado para 6 aplicacións: Industrial Automation, Motor Control, Data Acquisition Systems, Medical Equipment, Communication Systems, Test and Measurement.
Industrial Automation
The ADUM3154BRSZ-RL7 provides galvanic isolation for SPI communication between PLCs, sensors, and actuators. Its 3750Vrms isolation and 25kV/µs CMTI ensure reliable operation in noisy industrial environments. The 17MHz SPI clock rate supports high-speed data transfer for real-time control, while the multiple-slave capability allows connection of up to four SPI devices, reducing component count and simplifying design.
Recomendado
Motor Control
In motor control systems, the ADUM3154BRSZ-RL7 isolates the microcontroller from the power stage, protecting against high-voltage transients and ground loops. The low propagation delay and jitter ensure accurate timing for PWM signals, while the 34Mbps data rate allows fast communication with encoder interfaces. The wide operating temperature range (-40°C to +125°C) makes it suitable for harsh motor environments.
Recomendado
Data Acquisition Systems
The ADUM3154BRSZ-RL7 is ideal for isolating SPI buses in data acquisition systems, where it prevents ground loops and noise from corrupting analog measurements. Its 3750Vrms isolation protects sensitive ADCs from high common-mode voltages. The support for up to four SPI slaves allows multiple sensors to be connected through a single isolator, simplifying PCB layout and reducing cost.
Recomendado
Medical Equipment
In medical devices, patient safety requires galvanic isolation between the patient-connected circuitry and the main control unit. The ADUM3154BRSZ-RL7 provides 3750Vrms isolation, meeting safety standards for medical equipment. Its low power consumption and high reliability make it suitable for battery-powered devices. The multiple-slave SPI support enables connection of various sensors and actuators while maintaining isolation.
Recomendado
Communication Systems
The ADUM3154BRSZ-RL7 is used in communication systems to isolate SPI interfaces between baseband processors and RF front-ends, preventing ground loops and reducing noise. Its high CMTI (25kV/µs) ensures reliable operation in environments with high electromagnetic interference. The 17MHz SPI clock rate supports high-speed configuration of RF transceivers, while the compact SSOP package saves board space.
Recomendado
Test and Measurement
In test and measurement equipment, the ADUM3154BRSZ-RL7 isolates the measurement circuitry from the host controller, ensuring accurate readings by eliminating ground noise. Its 3750Vrms isolation protects sensitive inputs from high voltages. The low jitter and propagation delay are critical for maintaining signal integrity in high-speed SPI communication, making it ideal for oscilloscopes, data loggers, and spectrum analyzers.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ADUM3154BRSZ-RL7 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | ADUM3154BRSZ | ADUM3153BRSZ-RL7 | ADUM3151BRSZ-RL7 |
|---|---|---|---|---|
| Package | 20-SSOP | 20-SSOP | 20-SSOP | 20-SSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Isolation Voltage | 3750 Vrms | 3750 Vrms | 3750 Vrms | 3750 Vrms |
| Number of Channels | 7 (4 forward, 3 reverse) | 7 (4 forward, 3 reverse) | 6 (3 forward, 3 reverse) | 4 (2 forward, 2 reverse) |
| Data Rate | 34 Mbps | 34 Mbps | 34 Mbps | 34 Mbps |
| CMTI | 25 kV/µs | 25 kV/µs | 25 kV/µs | 25 kV/µs |
| SPI Clock Rate | 17 MHz | 17 MHz | 17 MHz | 17 MHz |
| Supply Voltage VDD1 | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V |
Diferenciadores clave
- Supports up to four SPI slave devices (frente a ADUM3153BRSZ-RL7)
- Higher isolation voltage than ADUM3154ARIZ (frente a ADUM3154ARIZ)
- Tape and reel packaging for automated assembly (frente a ADUM3154BRSZ)
Notas de diseño
Ensure proper PCB layout to minimize coupling across the isolation barrier. The datasheet recommends that any coupling that occurs should affect all pins equally on a given component side to prevent voltage differentials that could exceed absolute maximum ratings. Use a solid ground plane under the device and keep the isolation barrier clear of copper traces.
Decouple both VDD1 and VDD2 with 0.1µF ceramic capacitors placed as close to the pins as possible. Additionally, use a 10µF bulk capacitor on each supply rail to handle transient currents. The device operates with VDD1 from 3.0V to 3.6V and VDD2 from 4.5V to 5.5V, so ensure stable supplies within these ranges.
Do not exceed the absolute maximum ratings for input voltages or output currents. The device is designed for SPI communication, so ensure that the SPI signals are properly terminated and that the clock rate does not exceed 17 MHz. Also, verify that the isolation rating is sufficient for your application's safety requirements.
Información de cumplimiento
RoHS compliance indicated on Veswin Electronics product page. Other compliance information not specified in provided data.