ATSAML22G17A-MUT - 32MHz Cortex-M0+ MCU 128KB Flash | Microchip
N.º de pieza: ATSAML22G17A-MUT ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $4.18 | $4,18 |
| 10 | $3.76 | $37,60 |
| 100 | $3.18 | $318,00 |
| 500 | $2.74 | $1.370,00 |
| 1.000 | $2.46 | $2.460,00 |
| 3.000 | $2.21 | $6.630,00 |
ATSAML22G17A-MUT Descripción general
An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed by Arm that delivers higher code density and energy efficiency than 8/16-bit cores while maintaining a low gate count. It sits within the broader hierarchy of microcontroller -> embedded processor -> SoC -> semiconductor. Microchip's SAM L22 family targets battery-powered and energy-harvesting applications by combining a Cortex-M0+ core with sophisticated power management technologies, on-chip peripherals, and segment LCD driving capability.
Key features include the Cortex-M0+ core with single-cycle hardware multiply, 128KB Flash, 16KB SRAM, a 12-bit ADC, multiple SERCOM interfaces configurable as UART/SPI/I2C, Full-Speed USB 2.0 with device and host modes, a segment LCD controller (up to 4x40 segments), and an Event System for peripheral-to-peripheral signalling without CPU involvement. The 48-QFN package integrates an exposed pad for improved thermal dissipation and board-level grounding.
The SAM L22 architecture pairs the Cortex-M0+ core with a low-leakage process technology and a dedicated SleepWalking peripheral set. Power domains can be gated independently so SERCOM, ADC, or timer activity does not wake the CPU unless required. This makes the device well-suited for always-on sensor reading, smart-metering, and wearable designs that demand years of battery life.
Typical applications include battery-powered IoT sensor nodes, smart thermostats and metering devices, wearable health monitors, remote controls, segment-LCD user-interface panels, USB peripherals, and industrial sensor hubs. The integrated segment-LCD controller eliminates an external driver IC, reducing both BOM cost and PCB area for any product that needs a numeric or alphanumeric display.
When designing with this device, plan power-rail sequencing carefully because the SAM L22 has separate AVDD/VDDIO/VDDIN rails. Use a 1uF X7R ceramic decoupling capacitor on each supply pin placed as close to the IC as possible, and provide a USB- compliant 1uF capacitor on VBUS when the USB peripheral is used. Refer to Microchip application notes for low-power firmware patterns and segment-LCD bias generation.
This page synthesizes distributor pricing from DigiKey and Mouser, drop-in alternatives from the SAM L22 family and the Sitel MPN cross-reference, and practical design notes that go beyond what is printed in the manufacturer datasheet.
Alternativas directas para ATSAML22G17A-MUT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con ATSAML22G17A-MUT (mismo factor de forma y huella) — difiere en Package, Operating Temperature, ADC, Active Current, SRAM.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
ATSAML22G16A-MUT
✅ Sustitución directa✓ En stock
$2.45 / unidad
Ver hoja de datos →ATSAML22G17A-AUT
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$3.35 / unidad
Ver hoja de datos →ATSAML21G17B-MUT
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$2.25 / unidad
Ver hoja de datos →ATSAML21E16B-MUT
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$2.3 / unidad
Ver hoja de datos →ATSAML22G17A-MUT Valores máximos y características eléctricas
| Core Processor | ARM Cortex-M0+ |
| Core Size | 32-Bit Single-Core |
| Maximum CPU Clock | 32 MHz |
| Flash Memory | 128 KB (128K x 8) |
| SRAM | 16 KB |
| Supply Voltage (VDD) | 1.6 V to 3.6 V |
| Temperatura de funcionamiento | -40 C to +85 C |
| Encapsulado | 48-QFN (7x7 mm) |
| Tipo de montaje | Surface Mount |
| Connectivity | I2C, SPI, UART, USB |
| USB | Full-Speed USB 2.0 (Device and Host) |
| Peripherals | LCD controller, ADC, DMA, POR, WDT, RTC |
| ADC | 12-bit SAR ADC |
| Active Current (CoreMark) | 39 uA/MHz (typ) |
| Backup Current with RTC | 490 nA (typ, ultra-low-power backup mode) |
| Nivel MSL | 3 (per JEDEC J-STD-020) |
| Estado RoHS | Compliant |
| Carrier Type | Tape & Reel (MUT suffix) |
Configuración de pines de ATSAML22G17A-MUT
| Pin 1 | VDDIO — Digital I/O supply voltage |
| Pin 2 | PA00 — GPIO / SERCOM1[0] |
| Pin 3 | PA01 — GPIO / SERCOM1[1] |
| Pin 4 | PA02 — GPIO / AIN0 (ADC) |
| Pin 5 | PA03 — GPIO / AIN1 (ADC) |
| Pin 6 | GND — Ground |
| Pin 7 | PA04 — GPIO / AIN2 (ADC) |
| Pin 8 | PA05 — GPIO / AIN3 (ADC) |
| Pin 9 | PA06 — GPIO / AIN4 (ADC) |
| Pin 10 | PA07 — GPIO / AIN5 (ADC) |
| Pin 11 | PA08 — GPIO / NTP13 |
| Pin 12 | PA09 — GPIO / NTP14 |
| Pin 13 | PA10 — GPIO / NTP15 |
| Pin 14 | PA11 — GPIO / NTP0 |
| Pin 15 | VDDIN — Voltage regulator input supply |
| Pin 16 | GND — Ground |
| Pin 17 | PA12 — GPIO / NTP2 |
| Pin 18 | PA13 — GPIO / NTP3 |
| Pin 19 | PA14 — GPIO / NTP4 |
| Pin 20 | PA15 — GPIO / NTP5 |
| Pin 21 | PA16 — GPIO / SERCOM1[0] |
| Pin 22 | PA17 — GPIO / SERCOM1[1] |
| Pin 23 | PA18 — GPIO / SERCOM1[2] |
| Pin 24 | PA19 — GPIO / SERCOM1[3] |
| Pin 25 | PA20 — GPIO / SERCOM3[0] |
| Pin 26 | PA21 — GPIO / SERCOM3[1] |
| Pin 27 | PA22 — GPIO / SERCOM3[2] |
| Pin 28 | PA23 — GPIO / SERCOM3[3] |
| Pin 29 | PA24 — GPIO / USB_DM |
| Pin 30 | PA25 — GPIO / USB_DP |
| Pin 31 | PA26 — GPIO |
| Pin 32 | PA27 — GPIO |
| Pin 33 | PA28 — GPIO / RESET_N |
| Pin 34 | PA29 — GPIO / SWDIO |
| Pin 35 | PA30 — GPIO / SWCLK |
| Pin 36 | PA31 — GPIO |
| Pin 37 | PB00 — GPIO / LCD segment |
| Pin 38 | PB01 — GPIO / LCD segment |
| Pin 39 | PB02 — GPIO / LCD segment |
| Pin 40 | PB03 — GPIO / LCD segment |
| Pin 41 | PB04 — GPIO / LCD common |
| Pin 42 | PB05 — GPIO / LCD common |
| Pin 43 | PB06 — GPIO |
| Pin 44 | PB07 — GPIO |
| Pin 45 | PB08 — GPIO |
| Pin 46 | PB09 — GPIO |
| Pin 47 | AVDD — Analog supply voltage |
| Pin 48 | VSW — Voltage regulator switching output |
Aplicaciones típicas
ATSAML22G17A-MUT es adecuado para 6 aplicacións: Battery-Powered IoT Sensor Node, Smart Meter / Segment-LCD Display, Wearable Health Monitor, USB Human-Interface Device (HID), Smart Thermostat with Segment LCD, Industrial Sensor Hub / Modbus Bridge.
Battery-Powered IoT Sensor Node
The ATSAML22G17A-MUT's 39 uA/MHz active current and 490 nA backup-mode draw make it ideal for coin-cell or energy-harvesting IoT sensor nodes that must run for years without maintenance. The 128 KB Flash accommodates LoRaWAN/Sigfox/Thread stacks plus sensor drivers and a secure boot loader, while 16 KB SRAM handles wireless protocol buffers and sensor fusion. SleepWalking peripherals let UART, ADC, and GPIO wake the CPU only when real work is needed, eliminating idle polling. The 1.6V to 3.6V supply range supports single-cell alkaline, NiMH, and Li-MnO2 cells with direct connection to the integrated low-dropout regulator.
Recomendado
Smart Meter / Segment-LCD Display
The integrated segment LCD controller (up to 4x40 segments) eliminates an external driver IC on electricity, water, gas, and heat meters, reducing BOM cost and PCB area. The ATSAML22G17A-MUT's ultra-low-power backup mode with full SRAM and RTC retention lets the meter track cumulative consumption and time-stamp events for years on the backup battery alone. The 12-bit ADC can sample CT or shunt signals at low duty cycles while the CPU stays asleep, and SleepWalking lets ADC compare-result events wake the application layer only when thresholds are crossed. The wide 1.6V to 3.6V supply range accommodates lithium primary cells that decay gracefully.
Recomendado
Wearable Health Monitor
Wearable fitness bands and continuous-health monitors demand sub-mA average current draw and small PCB area. The ATSAML22G17A-MUT's Cortex-M0+ core delivers the throughput needed for heart-rate, SpO2, and accelerometer signal processing while spending most of its time in backup mode. The 490 nA RTC-retention current combined with SleepWalking GPIO wake-ups lets a wearable idle on a coin cell for months between charges. The integrated segment LCD controller drives small status displays without a separate driver chip, and the 48-QFN's 7x7 mm footprint fits wristband PCBs. USB support enables firmware updates and battery charging with no extra bridge IC.
Recomendado
USB Human-Interface Device (HID)
The on-chip Full-Speed USB 2.0 device-and-host controller lets the ATSAML22G17A-MUT implement keyboards, mice, game controllers, custom HID peripherals, and USB-to-UART bridges without an external PHY. The 128 KB Flash holds USB stacks plus HID report handlers and DFU boot loaders, while 16 KB SRAM serves as USB endpoint buffer space. The integrated 48 MHz internal PLL with USB clock recovery removes the cost of an external crystal on many designs. Low active current and SleepWalking peripherals keep USB dongles and battery-powered peripherals cool and energy-efficient.
Recomendado
Smart Thermostat with Segment LCD
Smart thermostats combine a segment LCD for status display, low-power wireless (Zigbee, Thread, BLE, or Wi-Fi co-processor), and mains or battery power. The ATSAML22G17A-MUT's integrated segment LCD controller eliminates the display-driver cost, and the Cortex-M0+ core handles UI logic, schedule storage, and sensor polling. Six SERCOM modules talk to the wireless co-processor, NVRAM, and temperature/humidity sensors over SPI, I2C, or UART. The 128 KB Flash stores UI translations, scheduling algorithms, and a wireless-stack bridge, while ultra-low-power modes extend battery life when AC power is removed.
Recomendado
Industrial Sensor Hub / Modbus Bridge
Industrial sensor hubs and Modbus bridges aggregate analog and digital sensor data and forward it to a PLC or cloud gateway. The ATSAML22G17A-MUT's 12-bit ADC, multiple SERCOM (UART/SPI/I2C) interfaces, and Event System let a single MCU poll many sensors with minimal CPU involvement. The wide 1.6V to 3.6V supply accommodates industrial 24V rails via a simple LDO, and the -40C to +85C industrial temperature rating covers most factory environments. DMA-driven SERCOM transfers and SleepWalking ADC compare wake-ups keep idle current below 1 mA even with multiple sensors polled.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ATSAML22G17A-MUT — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | ATSAML22G16A-MUT | ATSAML22G17A-AUT | ATSAML21G17B-MUT | ATSAML21E16B-MUT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 48-QFN (7x7) | 48-QFN (7x7) - same | 48-TQFP - different mechanical | 48-QFN (7x7) - same | 48-QFN (7x7) - same |
| Core | ARM Cortex-M0+ 32 MHz | ARM Cortex-M0+ 32 MHz | ARM Cortex-M0+ 32 MHz | ARM Cortex-M0+ 48 MHz (SAM L21) | ARM Cortex-M0+ 48 MHz (SAM L21) |
| Flash | 128 KB | 64 KB (-50%) | 128 KB (same) | 128 KB (same) | 64 KB (-50%) |
| SRAM | 16 KB | 8 KB (-50%) | 16 KB (same) | 16 KB (same) | 8 KB (-50%) |
| USB | Full-Speed USB 2.0 device/host | Full-Speed USB 2.0 device/host | Full-Speed USB 2.0 device/host | Full-Speed USB 2.0 device/host | Full-Speed USB 2.0 device/host |
| Segment LCD Controller | Yes (up to 4x40 segments) | Yes | Yes | No (SAM L21 omits LCD) | No (SAM L21 omits LCD) |
Diferenciadores clave
- Integrated segment LCD controller with ultra-low-power retention (frente a ATSAML21G17B-MUT)
- Higher Flash density at the same QFN-48 pinout (frente a ATSAML22G16A-MUT)
- 490 nA backup-mode current with full RTC and SRAM retention (frente a ATSAML21E16B-MUT)
Notas de diseño
Decouple every supply pin of the ATSAML22G17A-MUT with a 1uF X7R ceramic capacitor placed within 2 mm of the pin. VDDIN supplies the on-chip voltage regulator that generates VDDCORE; a 1uF cap on VDDIN is critical for clean regulation during SleepWalking events. VSW (the regulator switching node) needs its own 1uF cap. Provide separate analog (AVDD) and digital (VDDIO) grounds tied together at a single point near the IC to avoid injecting digital switching noise into ADC readings. Estimated: with three 1uF ceramic caps and one 100nF cap on each SERCOM pair, total BOM cost is under 0.10 USD.
The 48-QFN exposed thermal pad must be soldered to the board ground plane to keep junction temperature in spec. Per Microchip layout guidelines, the pad should contain at least eight 0.3 mm thermal vias arranged in a 3x3 grid connecting to a 1 square inch copper plane on the opposite side of the PCB. At 39 uA/MHz active current and 3.3 V supply, typical full-speed power is only 4 mW, so thermal management is rarely a concern - the via pattern matters more for electrical grounding than heat dissipation. Estimated: with a 1 square inch 1 oz copper plane, theta_JA drops to ~30 C/W, well within the -40 C to +85 C industrial range.
Route the USB D+/D- pair (PA24/PA25) as a 90-ohm differential pair with no stubs, keeping them short and matched within 150 mil. Place the 27-ohm series termination resistors and the USBLC6-2SC6 ESD protection array as close to the USB connector as possible. The SWDIO/SWDCLK pair (PA29/PA30) should also be kept short and routed away from switching signals to support clean firmware debug. Avoid routing the segment LCD signals under noisy traces - they are sensitive to capacitive coupling which can cause ghost segments on the display.
Do not leave the RESET_N line floating - it requires an external 10 kohm pull-up to VDDIO. Failure to provide a clean reset will cause boot failures and unpredictable behavior on power-up. The SERCOM I/O pins are multiplexed and must be configured via the PORT multiplexer before use; configuring a peripheral function on the wrong pin group is a common source of 'dead GPIO' debugging sessions. Always enable the brown-out detector (BOD33) in firmware to safely recover from low-voltage brown-out events on battery-powered designs.
Información de cumplimiento
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - automotive applications should reference -AUT/-MUT part numbers with explicit automotive-grade ordering codes. Lead-free matte-tin plating on the QFN package. MSL-3 floor life per JEDEC J-STD-020.
