DSPIC30F4013-30I/P - 16-bit DSC, 30 MIPS, 40-PDIP | Microchip
N.º de pieza: DSPIC30F4013-30I/P ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $12.2 | $12,20 |
| 10 | $10.85 | $108,50 |
| 100 | $9.6 | $960,00 |
| 500 | $8.55 | $4.275,00 |
| 1.000 | $7.75 | $7.750,00 |
DSPIC30F4013-30I/P Descripción general
What is a Digital Signal Controller? A DSC is a hybrid device that merges the deterministic interrupt response and peripheral set of a microcontroller with the single-cycle MAC, multiply-accumulate engine, and DSP library support of a digital signal processor. In the taxonomy of embedded processors, DSC sits between microcontroller (MCU) and digital signal processor (DSP), with the dsPIC30F family specifically targeting motor control, digital power conversion, and real-time signal conditioning where loop rates of a few to tens of kHz are common.
Key features of the DSPIC30F4013-30I/P include 84 base instructions, a 17x17-bit hardware multiplier, 40 MHz maximum clock (yielding 30 MIPS with a 4-cycle pipeline), and 20 general-purpose digital I/O pins. The device supports 3.0 V to 5.5 V single-supply operation across the industrial -40C to +85C range and provides a JTAG port plus an ICSP in-circuit serial programming interface. The 30I suffix denotes the -40C to +85C industrial operating range.
Architecturally the part uses a modified Harvard layout with separate program and data paths, dual 40-bit accumulators, and barrel shifter support for Q15 fractional math. The on-chip peripherals share a deterministic interrupt controller with 5-cycle latency, enabling the tight control loops required by brushless DC, AC induction, and switched-mode power supply designs.
Typical applications span 3-phase BLDC and PMSM motor drives, switch-mode power supply control loops, sensorless field-oriented control, audio processing front-ends, and industrial sensor conditioning. The 30 MIPS throughput is well-matched to low- to mid-speed drives and converters operating in the 1-50 kHz PWM range.
A key design consideration is input clock strategy - the integrated PLL requires careful loop filter component selection to meet motor-control EMI targets. The PDIP-40 package simplifies breadboard and through-hole prototyping and is widely supported by MPLAB X IDE, the XC16 compiler, and Microchip's motor-control application library.
This page synthesizes distributor pricing, drop-in package variants, and practical design considerations not always visible on a single manufacturer datasheet page.
Alternativas directas para DSPIC30F4013-30I/P — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con DSPIC30F4013-30I/P (mismo factor de forma y huella) — difiere en Core Architecture, Package, ADC, Operating Temperature, Timers.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
DSPIC30F4013-20I/P
✅ Sustitución directa✓ En stock
$4.55 / unidad
Ver hoja de datos →DSPIC30F4013-30I/P Valores máximos y características eléctricas
| Product Type | 16-bit Digital Signal Controller (DSC) |
| Core Architecture | Modified Harvard, dsPIC30F |
| Maximum CPU Speed | 30 MIPS (40 MHz oscillator, 4-cycle pipeline) |
| Program Memory (Flash) | 48 KB |
| RAM | 2 KB |
| Data EEPROM | 1 KB |
| Instruction Set | 84 base instructions, 17x17 hardware multiplier, dual 40-bit accumulators |
| Tensión de alimentación | 3.0 V to 5.5 V |
| Digital I/O Pins | 20 |
| ADC | 10-bit, 6 channels (Motor Control PWM-triggered) |
| Motor Control PWM | 6-channel, 16-bit resolution with dead-time control |
| Quadrature Encoder Interface (QEI) | Yes |
| Communication Peripherals | UART, SPI, I2C |
| Timers | 16-bit Timer (x3), 32-bit Timer |
| Temperatura de funcionamiento | -40C to +85C (Industrial) |
| Encapsulado | 40-pin PDIP (P) |
| Tipo de montaje | Through-Hole |
| Estado RoHS | Compliant |
Configuración de pines de DSPIC30F4013-30I/P
| Pin 1 | EMUD/EMUC — ICD primary communication pair / I/O port |
| Pin 2 | AVDD — Analog positive supply |
| Pin 3 | AVSS — Analog ground |
| Pin 4 | MCLR — Master Clear (reset) input |
| Pin 5 | RC15/OSC2/CLKO — Oscillator output / I/O port |
| Pin 6 | RC13/SOSC1/SOSCI — Secondary oscillator input / I/O port |
| Pin 7 | RC14/SOSC2/SOSCO — Secondary oscillator output / I/O port |
| Pin 8 | VDD — Digital positive supply |
| Pin 9 | VSS — Digital ground |
| Pin 10 | RB0/INT0 — External interrupt 0 / port B |
| Pin 11 | RB1/INT1 — External interrupt 1 / port B |
| Pin 12 | RB2/INT2 — External interrupt 2 / port B |
| Pin 13 | RB3/INT3 — External interrupt 3 / port B |
| Pin 14 | RB4/INT4 — External interrupt 4 / port B |
| Pin 15 | RB5 — I/O port B |
| Pin 16 | RB6/PGEC1 — ICSP clock / port B |
| Pin 17 | RB7/PGED1 — ICSP data / port B |
| Pin 18 | RD0 — I/O port D |
| Pin 19 | RD1 — I/O port D |
| Pin 20 | RD2 — I/O port D |
| Pin 21 | RD3 — I/O port D |
| Pin 22 | RD4 — I/O port D |
| Pin 23 | RD5 — I/O port D |
| Pin 24 | RD6 — I/O port D |
| Pin 25 | RD7 — I/O port D |
| Pin 26 | RC1/TXD — UART transmit / port C |
| Pin 27 | RC2/SCK/SCL — SPI clock / I2C clock / port C |
| Pin 28 | RC3/SDI/SDA — SPI data in / I2C data / port C |
| Pin 29 | RC4/SDO — SPI data out / port C |
| Pin 30 | RF6/U2RX — UART2 receive / port F |
| Pin 31 | RE8/INT1 — External interrupt 1 / port E |
| Pin 32 | RE9/INT2 — External interrupt 2 / port E |
| Pin 33 | RE0/PWM1H — PWM output 1 high-side / port E |
| Pin 34 | RE1/PWM1L — PWM output 1 low-side / port E |
| Pin 35 | RE2/PWM2H — PWM output 2 high-side / port E |
| Pin 36 | RE3/PWM2L — PWM output 2 low-side / port E |
| Pin 37 | RE4/PWM3H — PWM output 3 high-side / port E |
| Pin 38 | RE5/PWM3L — PWM output 3 low-side / port E |
| Pin 39 | RF7/U2TX — UART2 transmit / port F |
| Pin 40 | AVDD — Analog positive supply |
Aplicaciones típicas
DSPIC30F4013-30I/P es adecuado para 6 aplicacións: 3-Phase BLDC / PMSM Motor Drive, Switch-Mode Power Supply (SMPS) Control, Industrial Sensor Signal Conditioning, Audio Processing Front-End, Educational Robotics and Teaching Platforms, Uninterruptible Power Supply (UPS) / Inverter Controllers.
3-Phase BLDC / PMSM Motor Drive
The DSPIC30F4013-30I/P's 6-channel Motor Control PWM with dead-time control and 10-bit ADC triggered from PWM edges makes it a direct fit for 3-phase brushless DC and PMSM motor inverters at switching frequencies typically 8-20 kHz. The QEI module decodes Hall-effect or incremental-encoder feedback for rotor position, while the 30 MIPS throughput handles field-oriented control math within 25 us loop windows.
Recomendado
Switch-Mode Power Supply (SMPS) Control
For digital control of isolated and non-isolated DC-DC converters and PFC stages, the DSPIC30F4013-30I/P delivers interrupt latency below 5 cycles that suits current-mode control loops at 50-200 kHz switching frequency. The 10-bit ADC samples inductor current and output voltage with PWM-edge synchronization, while the integrated DSP engine executes PI/PID compensators in fractional Q15 math for fixed-point stability.
Recomendado
Industrial Sensor Signal Conditioning
Industrial sensor applications leveraging the DSPIC30F4013-30I/P include temperature, pressure, and flow signal conditioning at the network edge, where its 5 V I/O tolerance simplifies interface to legacy 4-20 mA loops and 24 V sensors. The DSP engine can FIR-filter and decimate the 10-bit ADC stream before passing values over UART/SPI to a host PLC, offloading preprocessing from the upstream controller.
Recomendado
Audio Processing Front-End
The DSPIC30F4013-30I/P suits digital audio front-ends such as effects units, parametric EQ, and active crossover controllers operating at 48 kHz sample rates. Its 17x17 hardware multiplier executes biquad IIR and FIR filter coefficients with single-cycle MAC, while SPI pairs with external 16-/24-bit codecs. The 30 MIPS throughput supports 8-16 simultaneous biquad sections per audio channel.
Recomendado
Educational Robotics and Teaching Platforms
University courses and robotics kits commonly specify the DSPIC30F4013-30I/P for its through-hole 40-PDIP package, which fits neatly on solderless breadboards and is easy to socket and reprogram. The MPLAB X IDE, the free XC16 compiler, and Microchip's motor-control library lower the barrier for teaching real-time control theory, sensor integration, and DSP algorithm implementation.
Recomendado
Uninterruptible Power Supply (UPS) / Inverter Controllers
In single-phase line-interactive UPS systems and solar microinverters, the DSPIC30F4013-30I/P implements grid synchronization, MPPT, and inverter current-control loops. The PWM module generates complementary gate-drive signals with programmable dead-time suited to IGBT half-bridge stages, while the ADC synchronizes to PWM center for low-distortion current sampling across the AC line cycle.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para DSPIC30F4013-30I/P — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | DSPIC30F4013-20I/P |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 40-PDIP | 40-PDIP - same |
| CPU Speed | 30 MIPS (40 MHz) | 20 MIPS (33% slower) |
| Flash Memory | 48 KB | 48 KB (same die) |
| RAM | 2 KB | 2 KB |
| Data EEPROM | 1 KB | 1 KB |
| Motor-Control PWM Channels | 6 channels (16-bit) | 6 channels (16-bit) |
| ADC | 10-bit, 6 channels | 10-bit, 6 channels |
| Supply Voltage | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Operating Temperature | -40C to +85C (Industrial, /30I/) | -40C to +85C (Industrial, /20I/) |
Diferenciadores clave
- Through-hole 40-PDIP package for breadboard prototyping (frente a DSPIC30F4013-30I/PT)
- DSC with DSP MAC engine at 30 MIPS (frente a DSPIC30F4012-30I/P)
- Single 5 V supply operation without external LDO (frente a MCU-only PIC24FJ64GA002)
Notas de diseño
The DSPIC30F4013-30I/P has moderate power dissipation in a 40-PDIP package; with typical 5 V VDD and 20-40 mA active current draw the die-to-ambient thermal resistance is acceptable for closed-enclosure industrial designs. Place decoupling capacitors (100 nF X7R close to each VDD/AVDD pin plus a bulk 10 uF tantalum) to minimize internal regulator stress. Estimate: at IDD = 30 mA and 5 V, internal dissipation is approximately 0.15 W; the 40-PDIP package easily dissipates this without a heatsink.
For 40-PDIP breadboard and through-hole prototypes, keep a tight analog/digital supply split: route AVDD/AVSS separately from VDD/VSS with a ferrite bead and cap on each AVSS pin. Place the 10-bit ADC input RC filters (typically 100 ohm + 1 nF) within 5 mm of the ANx pin to suppress PWM edge-coupled noise. GND return paths must not pass under the PLL/OSC traces to avoid jitter.
Estimated: when using the PLL in HS/PLL modes the loop filter component values must match the Microchip-supplied errata for the silicon revision; substituting non-standard resistor/capacitor ratios causes frequency drift or lock failure at temperature extremes. Always use the device configuration bits in the source code to control the oscillator mode and never hardcode fuse settings incorrectly - some early F4013 silicon did not tolerate certain PLL ratios. Validate timing with the MPLAB SIM simulator before hardware bring-up.
The 6-channel Motor Control PWM module produces high dV/dt edges (several kV/us) on the PWM1H/L through PWM3H/L pins; route these as short matched pairs to the gate driver, and keep analog ADC inputs physically separated on the PCB. Ground the MCLR pin through the standard ICSP programming circuit (typically 10 kohm pull-up to VDD with the ICSP reset line driving through a diode or isolator) and never leave MCLR floating.
Información de cumplimiento
RoHS compliant per Microchip product page data. AEC-Q100 qualification is not standard for this part; for automotive motor-control applications request the AEC-Q100-validated derivative from Microchip. Halogen-free status not explicitly confirmed in the verified data and is left as unknown.
