FUSB302MPX - USB Type-C Controller with PD | onsemi
N.º de pieza: FUSB302MPX ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
FUSB302MPX Descripción general
A USB Type-C controller is a dedicated interface IC that manages the CC (Configuration Channel) lines of a USB Type-C connector. In the system hierarchy, it sits between the USB power path / USB 3.1 physical connector and the host microcontroller, handling attach detection, cable orientation, role swap, and PD message negotiation so the application processor does not need to bit-bang the PD protocol.
Key features of the FUSB302MPX include full USB Type-C CC-line termination and detection, a full-featured PD PHY supporting BMC (Biphase Mark Coding) signaling on the CC line, an I2C slave interface for host control, and integrated VCONN support for powering electronically marked cables. The programmable architecture lets firmware implement sink, source, or dual-role power policies in software.
Technically, the device integrates a PD transceiver with BMC encoding/decoding, comparator-based CC voltage monitoring for attach and orientation detection, and register-based configuration accessible over I2C at up to 400 kHz clock rates. The exposed-pad MLP-14 package provides low thermal impedance and short trace lengths, which benefits CC-line signal integrity at BMC data rates. RoHS-compliant, lead-free construction supports modern environmental requirements.
Typical applications include USB Type-C power adapters and chargers, smartphone and tablet port controllers, notebook and dock power negotiation, power banks with PD sink input, and monitor or display-port alternate-mode designs. In each case the FUSB302MPX handles CC attach detection and PD contract negotiation while the system MCU manages the actual power conversion stage.
A key design consideration: onsemi explicitly recommends the FUSB302BMPX for new designs; the FUSB302B family incorporates updates aligned to later USB-C specification releases, and per onsemi the B version is a drop-in replacement requiring no software optimization.
This page adds value beyond the manufacturer datasheet by synthesizing distributor availability, drop-in alternative guidance, design notes, and comparison data in one engineer-oriented reference.
Alternativas directas para FUSB302MPX — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con FUSB302MPX (mismo factor de forma y huella) — difiere en Package, Host Interface, Operating Temperature, Product Type, Function.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
FUSB302BMPX
✅ Sustitución directa✓ En stock
$0.42 / unidad
Ver hoja de datos →FUSB302B01MPX
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
FUSB302TMX
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
FUSB302MPX Valores máximos y características eléctricas
| Función | Programmable USB Type-C Controller with Power Delivery |
| USB Standard | USB 3.1 |
| Interfaz | I2C |
| Supply Voltage Range | 2.8 V to 5.5 V |
| Encapsulado | 14-MLP (2.5x2.5 mm), Exposed Pad |
| Tipo de montaje | Surface Mount |
| Número de pines | 14 |
| PD PHY | BMC signaling on CC line |
| CC Line Detection | Attach, orientation, role detection |
| VCONN Support | Yes |
| Programming | Firmware-programmable via I2C registers |
| Estado RoHS | Compliant |
| Packaging | Tape and Reel (T/R) |
Guía de configuración de pines de FUSB302MPX 14-mlp (2.5x2.5 mm), exposed pad
Configuración de pines para FUSB302MPX (encapsulado 14-mlp (2.5x2.5 mm), exposed pad). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para FUSB302MPX.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
FUSB302MPX es adecuado para 6 aplicacións: USB PD Chargers and Adapters, Smartphones and Tablets USB Type-C Ports, Laptops, Docks and Hubs, Power Banks with PD Input, Monitors and Display Alternate-Mode Systems, Embedded and Development Platforms.
USB PD Chargers and Adapters
The FUSB302MPX fits USB PD charger designs because its integrated BMC PD PHY negotiates voltage and current contracts on the CC line while its 2.8V to 5.5V supply range is easily met by charger housekeeping rails. In a typical source design, the controller senses attach and cable orientation on CC1/CC2, enables VCONN for e-marked cables, and relays negotiated contracts over I2C to the system MCU, which then commands the flyback or buck power stage to the requested PD voltage. Because PD protocol timing is handled in hardware, even a small, low-cost MCU can run the complete source policy. The trade-off is firmware complexity: all policy logic lives in host code rather than in autonomous silicon, which is why onsemi recommends the FUSB302B step for new designs facing current compliance testing.
Recomendado
Smartphones and Tablets USB Type-C Ports
Mobile devices were the primary target market for the FUSB302 family: the 2.5x2.5 mm 14-MLP package and low external-component count fit dense smartphone and tablet PCBs. The controller performs CC-line attach detection, orientation resolution, and role detection (sink, source, or audio accessory), and its PD PHY negotiates fast-charge contracts up to the levels allowed by the platform policy. Power consumption is minimal, preserving battery life in standby, and the I2C register interface integrates cleanly with application-processor power-management firmware. Designers should route CC1/CC2 as short matched traces to the connector to protect BMC signal integrity, and place the exposed pad on a solid ground pour. Onsemi recommends the FUSB302B variant for new mobile designs due to updated USB-C spec alignment.
Recomendado
Laptops, Docks and Hubs
In notebook docking stations and USB hubs, the FUSB302MPX acts as the Type-C port controller that manages attach, orientation, and PD contract negotiation between the host and upstream power. Docks typically operate as PD sinks on the upstream port while providing source functionality downstream, and the programmable register architecture of the FUSB302MPX lets firmware implement such dual-role policies flexibly. VCONN support powers electronically marked cables so the design can source above 3A where the cable rating permits. The exposed-pad MLP-14 package provides good thermal and ground performance for continuous high-power delivery. Because PD messaging timing is handled on-chip, the dock's main MCU is relieved of real-time protocol duties, simplifying firmware architecture and reducing bill-of-material cost.
Recomendado
Power Banks with PD Input
Power banks benefit from the FUSB302MPX in its sink role: the controller negotiates a PD contract with an external charger to recharge the bank's cells at the highest mutually supported voltage, then acts as a source when charging connected devices. The programmable nature of the FUSB302MPX makes role swapping straightforward, with firmware toggling CC terminations between Rd (sink) and Rp (source) via I2C registers. Its 2.8V to 5.5V operating range is compatible with the bank's boost-converter housekeeping rail. For e-marked 5A cables, VCONN output enables reading cable capability so the bank never advertises more current than the cable safely carries. Designers must ensure the CC pins are protected against ESD at the connector, per standard Type-C port requirements.
Recomendado
Monitors and Display Alternate-Mode Systems
Type-C monitors use controllers like the FUSB302MPX to negotiate PD power and signal role-swap or alternate-mode intent on the CC line. While SuperMUTeCapable alternate-mode configuration typically involves a separate superspeed mux controlled by the system, the FUSB302MPX supplies the PD messaging foundation: it detects attach, resolves orientation (which the mux needs for lane steering), and negotiates the power contract that determines how many watts the monitor receives or delivers upstream. The register-level interface lets monitor firmware coordinate PD events with DisplayPort link training and mux switching. Onsemi recommends the FUSB302B step for new monitor platforms to ease USB-C compliance testing under the current specification releases.
Recomendado
Embedded and Development Platforms
Single-board computers, development boards, and industrial embedded systems adopting USB Type-C ports use the FUSB302MPX as the low-cost CC and PD front end. Open-source driver libraries exist for the family, simplifying integration with Linux and RTOS hosts, and the I2C register interface means any MCU with a standard I2C peripheral can implement PD policy. The controller handles orientation detection so USB 3.1 superspeed muxes can be steered correctly, and its PD PHY negotiates input power for boards drawing 15W to 100W from PD chargers. For industrial designs, verify the operating temperature range in the current onsemi datasheet. New designs should use the FUSB302B variant per onsemi's recommendation for specification compliance.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para FUSB302MPX — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | FUSB302BMPX | FUSB302B01MPX | FUSB302TMX |
|---|---|---|---|---|
| Package | 14-MLP (2.5x2.5 mm), Exposed Pad | 14-MLP (2.5x2.5 mm), Exposed Pad - same | 14-MLP (2.5x2.5 mm), Exposed Pad - same | 14-MLP (2.5x2.5 mm), Exposed Pad - same |
| Brand | onsemi | onsemi | onsemi | onsemi (originally Fairchild) |
| Supply Voltage | 2.8 V to 5.5 V | 2.8 V to 5.5 V | 2.8 V to 5.5 V | 2.8 V to 5.5 V |
| USB Standard | USB 3.1 | USB 3.1 | USB 3.1 | USB 3.1 |
| PD PHY / BMC | Yes | Yes | Yes | Yes |
| USB-C Spec Alignment | Original revision (earlier spec releases) | Updated to latest spec releases | Updated to latest spec releases | Original revision |
| Recommended for New Designs | No (use B-step) | Yes | Yes | No |
Diferenciadores clave
- Confirmed drop-in replacement path exists (frente a FUSB302BMPX)
- Fully programmable PD policy (frente a FUSB302TMX)
- Compact exposed-pad MLP-14 package (frente a Cross-brand Type-C controllers (e.g., ST STUSB4500, QFN-12))
Notas de diseño
Connect the exposed pad of the 14-MLP package to a solid ground plane through an array of 4-9 vias directly under the pad. This exposed pad is the main ground return for the PD transceiver, so a floating or poorly connected pad degrades BMC signal quality on the CC lines and can cause PD message CRC failures during negotiation. Place the 0.1uF VDD decoupling capacitor within 1-2 mm of the supply pin, and add a 1uF bulk capacitor nearby for PD burst-current transients.
Route CC1 and CC2 from the connector to the FUSB302MPX as short, length-matched traces (ideally under 15 mm) on a layer adjacent to ground. The PD BMC waveform shares these pins with DC attach-level sensing, so coupling from adjacent switching regulator nodes or high-speed USB 3.1 superspeed pairs can corrupt PD arbitration. Keep a ground guard or at least 3x trace-width spacing from switching nodes, and add the standard ESD protection at the connector per USB Type-C port requirements.
The most common integration pitfall is software, not hardware: the original FUSB302 was developed while the USB-C specification was still changing, and per onsemi the FUSB302B variant incorporates updates that make USB-IF compliance easier and is the recommended part for new designs. When replacing an FUSB302MPX with the FUSB302BMPX, onsemi confirms no software optimization is required, but new firmware development should target the B-step register behavior and validate against current USB-C compliance test suites.
Información de cumplimiento
RoHS compliant and lead-free per onsemi/DigiKey product listings. REACH, halogen-free, and conflict-minerals status not stated in verified data - confirm via onsemi environmental documentation.
