Analog Devices

MAX3232EEWE+ - 1Mbps RS-232 Transceiver | Analog Devices

N.º de pieza: MAX3232EEWE+ ✓ Activo
3.0V to 5.5V Vdss Down to 10nA Id 16-pin SOIC Package
MOQ: 1 |

MAX3232EEWE+ Descripción general

The Analog Devices MAX3232EEWE+ is a dual-driver, dual-receiver RS-232 transceiver operating from 3.0V to 5.5V, supporting data rates up to 1Mbps in a 16-pin SOIC package. The device provides ±15kV ESD protection and a low-power design with shutdown current down to 10nA. It is a production-status, true RS-232 interface suitable for industrial control, instrumentation, data acquisition, and embedded serial communication systems.

An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 levels and converts incoming RS-232 signals back into logic-level signals. The MAX3232 belongs to the RS-232 transceiver family within interface ICs, where the dual-driver and dual-receiver arrangement provides two complete point-to-point serial channels. Its charge-pump-assisted implementation supports both 3.0V and 5.5V systems without requiring a negative supply.

Key features include operation across a 3.0V to 5.5V supply range, data rates up to 1Mbps, ±15kV ESD protection, and shutdown current down to 10nA. Two transmitters and two receivers allow simultaneous bidirectional communication on separate RS-232 links. The 16-pin SOIC package supports conventional surface-mount PCB assembly, while the manufacturer designates the MAX3232 family as production and provides the associated data sheet with a revision number of 10.

The MAX3232EEWE+ is identified as a full-duplex, 2/2 RS-232 transceiver. Its integrated charge-pump circuitry generates the voltage levels required by true RS-232, while the receiver side restores usable logic levels for the host controller. This combination allows a microcontroller, programmable logic controller, or UART-equipped processor to communicate with legacy RS-232 equipment through a compact two-channel interface.

Typical uses include factory automation equipment, industrial sensors, barcode and test instruments, serial adapters, and embedded control boards. The 1Mbps capability is useful when a system needs more link bandwidth than conventional low-speed serial interfaces provide. The ±15kV ESD rating adds protection at connector-facing pins, although board-level grounding, shielding, and signal-routing practices remain necessary in electrically noisy installations.

Designers should follow the manufacturer pin-description table when assigning connector and logic signals, and should place required charge-pump and bypass capacitors close to their designated pins. The unused driver output or receiver input should be handled according to the manufacturer guidance so that an unused channel does not float. Keep the RS-232 traces away from sensitive analog nodes and route chassis and signal-ground connections according to the system grounding strategy.

This page combines the manufacturer's device identification with practical interface guidance, package details, sourcing information, and drop-in alternatives. It is intended to help engineers evaluate the MAX3232EEWE+ for a new RS-232 design or identify a compatible substitute for an existing 16-pin SOIC assembly.

Alternativas directas para MAX3232EEWE+ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con MAX3232EEWE+ (mismo factor de forma y huella) — difiere en Package, ESD Protection, Product Type, Supply Voltage Range, Maximum Data Rate.

Texas Instruments
Package: 16-SSOP, 5.30 mm width
ESD Protection: +/-15 kV terminal-to-terminal
Product Type: RS-232 line driver/receiver transceiver
Comparar con MAX3232EEWE+ →
Texas Instruments
ESD Protection: ±15 kV IEC ESD protection
Product Type: Dual RS-232 line driver and receiver
Supply Voltage Range: 3 V to 5.5 V
Comparar con MAX3232EEWE+ →
Analog Devices
Package: 16-SOIC
Comparar con MAX3232EEWE+ →
Texas Instruments
Package: 16-SOIC (0.154 inch, 3.90 mm width)
ESD Protection: ±15 kV
Product Type: Dual RS-232 line driver/receiver transceiver
Comparar con MAX3232EEWE+ →
Texas Instruments
Package: 16-pin TSSOP
Product Type: Dual RS-232 line driver and receiver
Supply Voltage Range: 3V to 5.5V
Comparar con MAX3232EEWE+ →

MAX3232IPWR

✅ Sustitución directa
Texas Instruments
📦 16-pin SOIC
Dual RS-232 line driver and receiver · 2 channels · 2 channels · 3V to 5.5V · 250kbit/s · ±15kV · 5V logic · 0.1µF

Consulte el precio

Ver hoja de datos →

MAX3232EIDR

✅ Sustitución directa
Texas Instruments
📦 16-pin SOIC
Dual RS-232 line driver/receiver transceiver · 2 drivers · 2 receivers · 250 kbps · 3 V to 5.5 V · 3.3 V · RS-232 · ±15 kV

Consulte el precio

Ver hoja de datos →

MAX3232ECDR

✅ Sustitución directa
Texas Instruments
📦 16-pin SOIC
Dual RS-232 line driver and receiver · 2 channels · 3 V to 5.5 V · 250 kbps · ±15 kV IEC ESD protection · RS-232 · 2 transmit and 2 receive functions · 16-pin SOIC

Consulte el precio

Ver hoja de datos →

MAX3232CDBR

✅ Sustitución directa
Texas Instruments
📦 16-pin SOIC
RS-232 line driver/receiver transceiver · 2 · 2 · 3 V to 5.5 V · 250 kbit/s · 5 V logic · 300 uA · 0.1 uF

Consulte el precio

Ver hoja de datos →

ICL3232IBNZ-T

✅ Sustitución directa
📦 16-pin SOIC
Same 16-pin SOIC class and 2/2 RS-232 configuration; supply range, data rate, ESD rating, and temperature grade differ and must be confirmed against the design.

📋 Alternativa de referencia (no en el catálogo)

ICL3232ECBNZ-T

✅ Sustitución directa
📦 16-pin SOIC
Same 16-pin SOIC class and dual RS-232 channel arrangement; maximum data rate and low-power specifications may differ from the 1Mbps MAX3232EEWE+.

📋 Alternativa de referencia (no en el catálogo)

MAX3232EEWE+ Especificaciones

Product Type Dual RS-232 transceiver
Supply Voltage Range 3.0V to 5.5V
Maximum Data Rate 1Mbps
Number of Drivers 2
Number of Receivers 2
Duplex Mode Full duplex
ESD Protection ±15kV
Corriente de apagado Down to 10nA
Encapsulado 16-pin SOIC
Tipo de montaje Surface mount
Interface Standard True RS-232
Production Status Production
Manufacturer Data Sheet Revision Rev. 10

Guía de configuración de pines de MAX3232EEWE+ 16-pin soic

Configuración de pines para MAX3232EEWE+ (encapsulado 16-pin soic). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 16-pin soic para MAX3232EEWE+

No hay datos detallados de patillaje disponibles para MAX3232EEWE+.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

MAX3232EEWE+ es adecuado para 6 aplicacións: Factory Automation Controllers, Industrial Sensor and Data Acquisition, Test and Measurement Equipment, Embedded Serial Port Expansion, Barcode and Identification Terminals, Serial Adapters and Communication Cables.

🏭

Factory Automation Controllers

The MAX3232EEWE+ fits factory automation controllers that connect PLC modules, operator panels, and sensors over RS-232. Its two drivers and two receivers support two full-duplex channels, while the 3.0V to 5.5V supply range accommodates both modern controller rails and established 5V interfaces. Operation up to 1Mbps provides useful timing margin for bursts of configuration or diagnostic data. The ±15kV ESD protection strengthens connector-facing circuitry in industrial environments, although proper grounding, shielding, and surge control remain required.

📡

Industrial Sensor and Data Acquisition

The MAX3232EEWE+ is appropriate for industrial sensor hubs and data-acquisition equipment that must bridge a host UART to RS-232 instruments. Its dual full-dupplex arrangement can serve separate instrument and control links, while the 1Mbps maximum rate accommodates high-volume measurement bursts better than slow legacy serial links. The 3.0V to 5.5V range simplifies shared supply design, and ±15kV ESD protection helps manage charge associated with connector handling. Signal-ground routing should follow the selected equipment's grounding architecture.

🔧

Test and Measurement Equipment

The MAX3232EEWE+ supports test and measurement instruments that communicate with a PC, controller, or service terminal. A full-duplex channel can support command transmission and response reception without switching the data direction manually. The 1Mbps capability provides more bandwidth than conventional 115.2kbps links, while the dual-channel arrangement can connect two independent ports. Its 16-pin SOIC package is practical for compact instrument boards, and the 3.0V to 5.5V operating range eases migration between mixed-voltage logic systems.

🖥️

Embedded Serial Port Expansion

The MAX3232EEWE+ can add legacy RS-232 connectivity to an embedded controller that lacks a suitable transceiver. Two transmitters and two receivers allow two RS-232 ports to share one device without using separate single-channel transceivers. Because the MAX3232EEWE+ operates from 3.0V to 5.5V, it can be paired with either a 3.3V or 5V UART domain, subject to the logic-level specifications. Its 1Mbps capability supports both legacy control traffic and faster diagnostic protocols.

📱

Barcode and Identification Terminals

The MAX3232EEWE+ can interface barcode scanners, identification readers, and local terminals with RS-232 host ports. Full-duplex communication allows commands to be sent while status or read data returns on the same link, and the 1Mbps capability accommodates high-rate scan streams. The 16-pin SOIC package supports compact surface-mount assemblies, while shutdown current down to 10nA is useful in portable or intermittently powered equipment. Cable shielding and ground-reference practices should be selected for the installation environment.

🔌

Serial Adapters and Communication Cables

The MAX3232EEWE+ is suitable for active serial adapters that add true RS-232 capability to embedded equipment. Two full-duplex channels can support a data link plus hardware-flow-control signals or two related ports. The 3.0V to 5.5V supply compatibility permits operation from common USB-to-serial controller rails, and ±15kV ESD protection is valuable when the adapter may be connected and disconnected frequently. The 16-pin SOIC footprint supports compact adapter boards, but connector protection and cable shielding remain separate design requirements.

What is the MAX3232EEWE+?
The MAX3232EEWE+ is a dual-driver, dual-receiver, full-duplex RS-232 transceiver made by Analog Devices. According to the manufacturer product page, it operates from 3.0V to 5.5V, supports data rates up to 1Mbps, provides ±15kV ESD protection, and is packaged in a 16-pin SOIC. It converts between logic-level UART signals and true RS-232 voltage levels.
What is the operating voltage of MAX3232EEWE+?
The MAX3232EEWE+ operates from 3.0V to 5.5V. According to the Analog Devices MAX3232 product page, this range supports both common low-voltage and legacy 5V system rails. The integrated charge-pump circuitry supports true RS-232 operation without a separate negative supply, simplifying the power architecture compared with older discrete-interface implementations.
How fast can MAX3232EEWE+ transmit RS-232 data?
The MAX3232EEWE+ supports RS-232 data rates up to 1Mbps. The Analog Devices product page identifies the MAX3232 family as a low-power, true RS-232 transceiver with a maximum data rate of 1Mbps. This capability is suitable for instrument-control links and embedded systems that need more throughput than a low-speed serial connection.
How many RS-232 channels does MAX3232EEWE+ provide?
The MAX3232EEWE+ provides two RS-232 drivers and two receivers, forming two full-duplex channels. The manufacturer product page identifies the device as a 2/2 full-duplex transceiver. Each channel can support communication between an RS-232 port and a host UART, subject to the data-rate and wiring requirements of the connected equipment.
Does MAX3232EEWE+ include ESD protection?
Yes, the MAX3232EEWE+ provides ±15kV ESD protection on the RS-232 interface. The Analog Devices MAX3232 data-sheet description identifies the device as a ±15kV ESD-protected transceiver. This protection strengthens connector-facing circuits, but engineers should still apply appropriate board layout, grounding, shielding, and surge-protection practices.
Where can I download the MAX3232EEWE+ datasheet PDF?
The official MAX3232EEWE+ datasheet can be accessed through the Analog Devices MAX3232 product page at https://www.analog.com/en/products/max3232.html. The product page links to the manufacturer data sheet, identified as Rev. 10, and includes the MAX3232 family selection table. Use its pin-description and typical-application sections when assigning the 16 SOIC pins.
Where can I find the MAX3232EEWE+ pinout?
The MAX3232EEWE+ pinout is available in the pin-description table of the Analog Devices MAX3232 data sheet. The device uses a 16-pin SOIC package and contains two transmitters, two receivers, charge-pump connections, supply pins, enable/shutdown control, and ground connections. Assign PCB tracks by following the numbered package drawing and manufacturer pin table exactly.
What are the key specifications of MAX3232EEWE+ that engineers should know?
The principal MAX3232EEWE+ specifications are a 3.0V to 5.5V supply range, 1Mbps maximum data rate, two drivers, two receivers, full-duplex operation, ±15kV ESD protection, and shutdown current down to 10nA. According to the Analog Devices product page, the device is a production-status true RS-232 transceiver in a 16-pin SOIC package.
Is MAX3232EEWE+ suitable for industrial equipment?
The MAX3232EEWE+ is suitable for many industrial serial interfaces because it combines a 3.0V to 5.5V supply range, 1Mbps operation, and ±15kV ESD protection. Its long-established 16-pin SOIC package and dual-channel arrangement suit PLC peripherals, test equipment, and factory data-acquisition systems. Site-specific EMC, surge, grounding, and environmental requirements still determine the final qualification.
What is the best drop-in replacement for MAX3232EEWE+?
The closest drop-in choices include the Analog Devices MAX3232IPWR, MAX3232EIDR, MAX3232ECDR, and MAX3232CDBR when their specified electrical ratings meet the design requirements. Renesas ICL3232IBNZ and ICL3232ECBNZ are also listed as similar parts. Confirm pin assignments, supply range, data rate, shutdown behavior, and ESD rating before approving any substitution.
Can MAX3232IPWR replace MAX3232EEWE+?
The MAX3232IPWR can serve as a board-compatible alternative in designs using the 16-pin SOIC footprint, but it is not automatically electrically identical. Check the supply range, maximum data rate, ESD rating, enable and shutdown behavior, and receiver thresholds against the original design. The manufacturer family information supports pin and package compatibility, while individual variant ratings must still be reviewed.
MAX3232EEWE+ vs ICL3232IBNZ-T: which is better for a new design?
Choose the MAX3232EEWE+ when its Analog Devices documentation and production status are preferred for the product being developed. The ICL3232IBNZ-T is identified as a similar 16-pin RS-232 transceiver and can serve as a sourcing alternative. The decisive criteria are verified supply range, data rate, ESD protection, shutdown current, lifecycle status, and qualification requirements.
When should I choose MAX3232EEWE+ over MAX3232ECDR?
Choose the MAX3232EEWE+ when the design requires the MAX3232E-style 1Mbps performance, ±15kV ESD protection, or shutdown current down to 10nA. Select MAX3232ECDR when its lower data rate and specified electrical characteristics are acceptable and its availability better fits the project. Both use the same 16-pin SOIC class of package, but functional features and ratings must be compared.
Where can I buy MAX3232EEWE+ and check its lead time?
Use the Request a Quote form on this page to ask about MAX3232EEWE+ availability, lead time, and order quantity. The form routes the request for current sourcing confirmation without presenting a static commercial figure. Engineers should include the required 16-pin SOIC variant, production quantity, and any automotive or industrial qualification requirements in the request.
What can replace MAX3232EEWE+ in a pin-compatible RS-232 design?
Several 16-pin SOIC alternatives can replace the MAX3232EEWE+ when their electrical ratings are acceptable. Same-manufacturer options include MAX3232IPWR, MAX3232EIDR, MAX3232ECDR, and MAX3232CDBR. The Renesas ICL3232IBNZ and ICL3232ECBNZ are listed as similar alternatives. Validate pinout, voltage range, data rate, ESD rating, and shutdown behavior before replacement.

Datos de referencia de ingeniería para MAX3232EEWE+ — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the MAX3232EEWE+ for a new 16-pin SOIC design that needs two full-duplex RS-232 channels, operation from 3.0V to 5.5V, data rates up to 1Mbps, ±15kV ESD protection, and shutdown current down to 10nA. It is especially appropriate for industrial instruments, controllers, and adapters requiring a current production-status family member. Consider MAX3232IPWR when its specific ratings meet the design and its sourcing position is preferable, but review its data-rate and shutdown limits. MAX3232EIDR is the closest same-family option for PCB reuse, subject to temperature and ordering-code checks. MAX3232ECDR or MAX3232CDBR may suit lower-speed links after their electrical limits are confirmed. For a second-source strategy, ICL3232IBNZ-T or ICL3232ECBNZ-T can fit the same 16-pin SOIC class, but the supply range, data rate, ESD rating, temperature grade, and lifecycle requirements must be verified before schematic approval.

Comparación con alternativas

Parámetro Este producto MAX3232IPWR MAX3232EIDR MAX3232ECDR MAX3232CDBR ICL3232IBNZ-T
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Renesas Electronics
Package 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC
Product Type Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver
Number of Drivers 2 2 2 2 2 2
Number of Receivers 2 2 2 2 2 2

Diferenciadores clave

  • Higher supported data rate than lower-speed MAX3232 family alternatives (frente a MAX3232ECDR)
  • Lower-power shutdown capability for intermittently powered systems (frente a MAX3232IPWR)
  • Documented connector-facing ESD protection (frente a MAX3232CDBR)

Notas de diseño

Place the charge-pump capacitors and supply bypass capacitors exactly where shown in the manufacturer typical-application diagram, using the shortest practical ground returns. The 16-pin SOIC footprint does not eliminate the need for careful trace length control: excessive loop area around charge-pump paths can increase radiated noise and reduce margin in sensitive installations.

Route each RS-232 driver and receiver trace directly toward its connector-side circuitry, and keep the differential path between the transceiver and connector as short and symmetric as practical. Separate RS-232 routes from clocks, sensor inputs, and precision analog signals. Use a deliberate signal-ground strategy at the connector rather than allowing return current to flow through unrelated digital ground paths.

Do not treat ±15kV ESD protection as a substitute for external surge or lightning protection. Verify the unused receiver input and unused driver output states, confirm the enable and shutdown levels for the selected logic rail, and confirm that the connected RS-232 equipment uses compatible signal-ground conventions. These checks prevent intermittent failures that can be mistaken for a defective transceiver.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The manufacturer page identifies the MAX3232 family as production, but the available product information does not explicitly state the compliance status of the MAX3232EEWE+ suffix. Environmental and quality requirements should be confirmed for the exact ordering code.

Datos verificados el: 2026-11-17 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

MAX3232EEWE+ datasheet MAX3232EEWE+ datasheet pdf MAX3232EEWE+ pinout MAX3232EEWE+ specifications Analog Devices MAX3232EEWE+ MAX3232EEWE+ 16 pin SOIC MAX3232EEWE+ RS-232 transceiver MAX3232EEWE+ equivalent MAX3232EEWE+ replacement MAX3232EEWE+ vs ICL3232IBNZ-T MAX3232EEWE+ cross reference MAX3232EEWE+ footprint MAX3232EEWE+ application circuit MAX3232EEWE+ price MAX3232EEWE+ stock

Componentes & términos relacionados

Analog Devices Maxim Integrated MAX3232EEWE+ MAX3232 MAX3232IPWR MAX3232EIDR MAX3232ECDR MAX3232CDBR ICL3232IBNZ-T ICL3232ECBNZ-T RS-232 transceiver interface IC line driver line receiver full-duplex communication charge-pump circuitry 3.0V to 5.5V power supply 1Mbps data rate ±15kV ESD protection 10nA shutdown current 16-pin SOIC SOIC package family surface-mount device UART interface industrial automation
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ