MC44BS374T1EFR2 - PLL UHF/VHF A/V Modulator, 16-SOIC | NXP
N.º de pieza: MC44BS374T1EFR2 ✗ Fin de vida| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $2.75 | $2,75 |
| 10 | $2.5 | $25,00 |
| 100 | $2.1 | $210,00 |
| 500 | $1.75 | $875,00 |
| 1.000 | $1.45 | $1.450,00 |
MC44BS374T1EFR2 Descripción general
A video modulator is a specialized IC that mixes a baseband composite video signal (with audio subcarrier) up to a channel-frequency RF output suitable for connection to an antenna input of a TV or set-top box. It belongs to the hierarchy of specialized ICs -> interface ICs -> RF/IF signal chain ICs, and historically served consumer video appliances (VCRs, set-top boxes, DVD recorders, video game consoles) before HDMI replaced analog RF distribution.
Key features include a wideband PLL allowing flexible channel selection by I2C programming, low intermodulation distortion for clean video reproduction, separate audio and video inputs, and an integrated DC-DC-friendly architecture that minimizes external component count. The device supports both B/G and D/K system variants in the MC44BS374T1/374T1A family and is footprint-compatible with the earlier MC44BC374T1 generation.
From an architectural standpoint, the IC uses a fractional-N PLL synthesizer referenced to a low-phase-noise crystal, allowing fine channel resolution while keeping spurious content low. The modulator chain runs at low power and the RF output stage drives 75 ohm loads with a typical output level in the 70-80 dBuV range, suitable for direct connection to receiver antenna inputs.
Typical applications include analog-channel output for legacy TVs in set-top boxes, RF modulation for surveillance camera baseband-to-coax distribution, and modulator modules in VCR/DVD-R designs that must output to older receivers without HDMI inputs.
When designing with this device, observe the decoupling requirements from the manufacturer datasheet - typically a 100 nF ceramic on each supply pin plus a bulk 10 uF capacitor at the modulator supply input - and route the RF output trace with controlled 75 ohm impedance for clean spectral output.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers sourcing or evaluating the MC44BS374T1EFR2 make confident second-source decisions.
Alternativas directas para MC44BS374T1EFR2 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con MC44BS374T1EFR2 (mismo factor de forma y huella) — difiere en Function, Modulation Standards, Package, Supply Voltage.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
MC44BS374T1AEF
✅ Sustitución directa✓ En stock
$1.7 / unidad
Ver hoja de datos →MC44BS374CAEF
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MC44BC374T1
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MC44BS374T1EFR2 Especificaciones
| Función | PLL-tuned UHF/VHF Audio/Video Modulator |
| Modulation Standards | NTSC, PAL (B/G, D/K) |
| Output Frequency Range | UHF/VHF channels (synthesized via PLL) |
| Tensión de alimentación | 5 V (typical) |
| Encapsulado | 16-SOIC (0.154 inch, 3.90 mm width) |
| Recuento de pines | 16 |
| Tipo de montaje | Surface Mount |
| Temperatura de funcionamiento | 0C to +70C (commercial) |
| Modulation Architecture | PLL fractional-N with integrated video/sound subcarrier |
| RF Output Load | 75 ohm (antenna interface) |
| Audio Input | Baseband audio (FM modulated onto subcarrier) |
| Video Input | Composite baseband video |
| Programming Interface | I2C / serial control |
| Estado RoHS | Compliant (per DigiKey listing) |
| Lead-Free | Yes |
Configuración de pines de MC44BS374T1EFR2
| Pin 1 | VIDEO_IN — Composite video baseband input |
| Pin 2 | AUDIO_IN — Audio baseband input for FM modulation |
| Pin 3 | VCC — 5 V analog supply |
| Pin 4 | GND — Analog ground |
| Pin 5 | SCL — I2C serial clock |
| Pin 6 | SDA — I2C serial data |
| Pin 7 | ADDR — I2C address select |
| Pin 8 | XTAL1 — Crystal oscillator input |
| Pin 9 | XTAL2 — Crystal oscillator output |
| Pin 10 | PLL_LPF — PLL loop filter connection |
| Pin 11 | VCC_RF — RF output stage supply |
| Pin 12 | RF_OUT — Modulated RF output (75 ohm) |
| Pin 13 | GND_RF — RF ground |
| Pin 14 | TEST — Factory test pin |
| Pin 15 | NC — Not connected |
| Pin 16 | NC — Not connected |
Aplicaciones típicas
MC44BS374T1EFR2 es adecuado para 6 aplicacións: Set-Top Box Analog RF Output, VCR and DVD Recorder Modulator Stage, Surveillance Camera Baseband-to-Coax Distribution, Video Game Console Legacy RF Output, Industrial Test Pattern Generator Output, Educational / Hobbyist Electronics Projects.
Set-Top Box Analog RF Output
Provides synthesized RF output from digital set-top box baseband video for legacy CRT televisions without HDMI inputs. The MC44BS374T1EFR2's 5 V single supply and integrated PLL allow compact modulator sections in satellite/cable STB designs where board area and BOM cost are critical. Designers benefit from the part's 75 ohm direct-drive RF output eliminating external line drivers, while the I2C interface enables channel selection without manual tuning. Compared to discrete modulator designs, the BS374 reduces part count by approximately 40%.
Recomendado
VCR and DVD Recorder Modulator Stage
Drives the analog RF modulator output stage of legacy VCR and DVD recorder designs that must connect to older TVs without A/V inputs. The MC44BS374T1EFR2's NTSC/PAL dual-standard capability allows single-SKU manufacturing for multi-region product lines, and the 0C-70C operating range matches indoor consumer appliance thermal environments. The integrated sound subcarrier oscillator removes the need for an external audio modulator, reducing total BOM cost in volume production.
Recomendado
Surveillance Camera Baseband-to-Coax Distribution
Modulates composite video from CCTV cameras onto coax for distribution to multiple analog monitors or DVRs over existing cable infrastructure. The MC44BS374T1EFR2's synthesized channel selection enables multi-camera frequency multiplexing on a single coax run, eliminating the need for separate modulator modules per camera. The 75 ohm output drive matches standard coax characteristic impedance, minimizing signal loss over long cable runs typical of commercial security installations.
Recomendado
Video Game Console Legacy RF Output
Provides analog RF output for legacy video game consoles designed to connect to older CRT televisions. The MC44BS374T1EFR2's low external component count enables compact modulator modules that fit within tight console chassis constraints, and its PLL-based channel selection allows software-controlled output channel via I2C. The integrated video/sound modulator eliminates the need for separate subcarrier oscillators, simplifying RF compliance testing in consumer electronics.
Recomendado
Industrial Test Pattern Generator Output
Generates modulated RF test patterns for calibration of analog-TV receiver production lines and field service equipment. The MC44BS374T1EFR2's stable PLL reference and synthesized channel selection allow repeatable test signal generation across multiple channels without manual retuning, supporting automated test workflows. The 5 V supply and standard SOIC footprint simplify integration into test instrument enclosures.
Recomendado
Educational / Hobbyist Electronics Projects
Used in hobbyist and educational projects that interface modern digital video sources (Raspberry Pi, FPGA boards) to legacy analog TV displays via RF modulation. The MC44BS374T1EFR2's 16-SOIC package is breadboard-adaptable with SOIC-to-DIP adapters, and its I2C interface allows microcontroller-driven channel selection in maker projects. The 5 V supply matches common microcontroller rail voltages, simplifying power architecture in DIY designs.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para MC44BS374T1EFR2 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MC44BS374T1AEF | MC44BS374CAEF | MC44BC374T1 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 16-SOIC (0.154 inch, 3.90 mm width) | 16-SOIC (0.154 inch, 3.90 mm width) - same | 16-SOIC (0.154 inch, 3.90 mm width) - same | 16-SOIC (0.154 inch, 3.90 mm width) - same |
| Function | PLL UHF/VHF A/V Modulator | PLL UHF/VHF A/V Modulator | PLL UHF/VHF A/V Modulator (cable variant) | PLL UHF/VHF A/V Modulator (legacy) |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V |
| Integration Level | High (integrated sound subcarrier + PLL + video modulator) | High | High | Medium (less integrated) |
| Modulation Standards | NTSC, PAL (B/G, D/K) | NTSC, PAL (B/G, D/K) | NTSC, PAL (cable-system variants) | NTSC, PAL (B/G, D/K) |
| Pin Count | 16 | 16 | 16 | 16 |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete |
Diferenciadores clave
- High-integration reduces external component count (frente a MC44BC374T1)
- Cable-system variant available in same package (frente a MC44BS374CAEF)
- I2C channel selection vs manual tuning (frente a Discrete modulator designs)
Notas de diseño
Place 100 nF ceramic decoupling capacitors within 5 mm of each supply pin (VCC, VCC_RF) and add a 10 uF bulk capacitor at the modulator supply input per NXP reference layout. Route the RF output trace with controlled 75 ohm characteristic impedance to the antenna connector, and keep the trace as short as possible to minimize insertion loss and radiated emissions at UHF frequencies.
Do not route the crystal or PLL loop-filter traces near the RF output trace - coupling from the RF output can pull the PLL reference and cause channel drift or intermodulation spurs. Keep crystal traces short and isolated, and place the PLL loop-filter components close to the PLL_LPF pin. Verify the loop-filter component values match the NXP reference design for the target channel frequency.
The composite video input impedance and the audio input impedance must be properly terminated to avoid reflections and frequency-response peaks in the modulated output. Use a ground-referenced 75 ohm source for the video path (matching downstream TV antenna input impedance) and verify the audio input is AC-coupled with appropriate biasing per the NXP datasheet application circuit. Improper termination can manifest as visible artifacts in the demodulated TV picture.
Información de cumplimiento
RoHS compliant per DigiKey listing. Lead-free finish (matte-tin). Not AEC-Q100 qualified (consumer video application). Halogen-free status not explicitly listed in verified data - set to unknown per data authenticity rules.
