PIC16F1713T-I/SS - 8-bit MCU, 7KB Flash, 32MHz, 28-SSOP | Microchip
N.º de pieza: PIC16F1713T-I/SS ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $1.84 | $1,84 |
| 10 | $1.65 | $16,50 |
| 100 | $1.47 | $147,00 |
| 500 | $1.3 | $650,00 |
| 1.000 | $1.15 | $1.150,00 |
PIC16F1713T-I/SS Descripción general
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals around an 8-bit data bus. Within the broader semiconductor taxonomy, MCUs sit inside the Integrated Circuits > Microcontrollers category, which itself belongs to the embedded computing hierarchy of processors, controllers, and finally semiconductors. The PIC16F1713 family specifically targets cost-sensitive analog-heavy applications where on-chip op-amps, DACs, and comparators eliminate external analog ICs.
Key features include integrated op-amps, a 10-bit ADC with up to 17 channels, 5-bit and 8-bit DACs, two high-speed comparators, Core Independent Peripherals (CLC, COG, NCO, Zero Cross Detect), Peripheral Pin Select (PPS), and dual CCP/PWM modules. Communication interfaces include EUSART, I2C, and SPI. The XLP sleep current is typically below 50 nA, enabling years of battery life in always-on sensor nodes.
Architecturally, the PIC16F1713 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word and a hardware multiplier. The CLC (Configurable Logic Cell) and NCO (Numerically Controlled Oscillator) peripherals operate without CPU intervention, allowing deterministic timing for motor control, lighting, and power-conversion feedback loops without software overhead.
Typical applications include LED lighting drivers, battery chargers, sensor signal conditioning, small motor control (fans, pumps), home appliances, and IoT edge nodes. The integrated op-amp + DAC + ADC + ZCD chain enables single-chip closed-loop constant-current LED drivers and zero-cross SSRs without any external analog components.
When designing with this part, allocate the PPS mapping carefully: many analog peripherals share pins, and remapping mid-design requires re-validating the PCB layout. The 28-SSOP footprint also limits I/O count to roughly 25 usable pins, so dense HMI designs should consider the 40-pin PIC16F1716 variant.
This page synthesizes distributor pricing, drop-in SSOP-28 alternatives, and practical design notes not found in the standalone manufacturer datasheet, giving engineers a faster decision path.
Alternativas directas para PIC16F1713T-I/SS — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PIC16F1713T-I/SS (mismo factor de forma y huella) — difiere en DAC, Package, ADC, Comparators, Core Independent Peripherals.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
PIC16F1713-I/SS
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
PIC16F1713-E/SS
✅ Sustitución directa✓ En stock
$1.05 / unidad
Ver hoja de datos →PIC16F1716-I/SS
✅ Sustitución directa✓ En stock
$1.52 / unidad
Ver hoja de datos →PIC16F1709-I/SS
✅ Sustitución directa✓ En stock
$1.1 / unidad
Ver hoja de datos →PIC16F1713T-I/SSVAO
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PIC16F1713T-I/SS Valores máximos y características eléctricas
| Core | PIC 8-bit enhanced mid-range |
| Program Memory (Flash) | 7 KB (4K x 14 words) |
| RAM | 512 bytes |
| Max CPU Frequency | 32 MHz |
| Operating Voltage Range | 1.8 V to 5.5 V |
| ADC | 10-bit, up to 17 channels |
| DAC | 5-bit and 8-bit |
| Comparators | 2 high-speed |
| Operational Amplifiers | 2 on-chip op-amps |
| Timers | 4 x 8-bit, 1 x 16-bit |
| PWM / CCP | 2 CCP / PWM channels |
| Communication | EUSART, I2C, SPI |
| Core Independent Peripherals | CLC, COG, NCO, ZCD, PPS |
| Encapsulado | 28-pin SSOP |
| Temperatura de funcionamiento | -40C to +85C (Industrial, "I") |
| Tipo de montaje | Surface Mount |
| Estado RoHS | Compliant |
| Lead-Free | Yes |
Configuración de pines de PIC16F1713T-I/SS
| Pin 1 | RA1/AN1/C1IN1-/C2IN1-/OPA1IN+ — Bidirectional I/O / Analog input / Comparator input / Op-amp 1 non-inverting input |
| Pin 2 | RA0/AN0/C1IN0+/C2IN0+/OPA1IN-/DAC1OUT — Bidirectional I/O / Analog input / Comparator input / Op-amp 1 inverting input / DAC1 output |
| Pin 3 | RA3/AN3/VREF+/C1IN3+/C2IN3+/OPA2IN+ — Bidirectional I/O / Analog input / Positive voltage reference / Comparator input / Op-amp 2 non-inverting input |
| Pin 4 | RA4/AN4/C1IN2-/C2IN2-/OPA2IN-/T0CKI — Bidirectional I/O / Analog input / Comparator input / Op-amp 2 inverting input / Timer0 clock input |
| Pin 5 | RA5/AN5/OPA2OUT/DAC2OUT — Bidirectional I/O / Analog input / Op-amp 2 output / DAC2 output |
| Pin 6 | RE3/MCLR/VPP — Input only / Master Clear (reset) / Programming voltage |
| Pin 7 | RA7/OSC1/CLKIN — Bidirectional I/O / Crystal oscillator input / External clock input |
| Pin 8 | RA6/OSC2/CLKOUT — Bidirectional I/O / Crystal oscillator output / Clock output |
| Pin 9 | RC1/CCP2/AN13 — Bidirectional I/O / CCP2 PWM output / Analog input |
| Pin 10 | RC0/SOSCO/AN16 — Bidirectional I/O / Secondary oscillator output / Analog input |
| Pin 11 | RC3/SCL/SCK/AN15 — Bidirectional I/O / I2C clock / SPI clock / Analog input |
| Pin 12 | RC4/SDA/SDI/AN14 — Bidirectional I/O / I2C data / SPI data in / Analog input |
| Pin 13 | RC5/SDO/AN12 — Bidirectional I/O / SPI data out / Analog input |
| Pin 14 | RC6/TX/CK/AN11 — Bidirectional I/O / EUSART TX / EUSART clock / Analog input |
| Pin 15 | RC7/RX/DT/AN10 — Bidirectional I/O / EUSART RX / EUSART data / Analog input |
| Pin 16 | RB7/ICSPDAT/AN9 — Bidirectional I/O / ICSP data / Analog input |
| Pin 17 | RB6/ICSPCLK/AN8 — Bidirectional I/O / ICSP clock / Analog input |
| Pin 18 | RB5/AN7/C2IN1-/CCP1/PGM — Bidirectional I/O / Analog input / Comparator input / CCP1 PWM / LVP programming |
| Pin 19 | RB4/AN6/C2IN0+ — Bidirectional I/O / Analog input / Comparator input |
| Pin 20 | RB3/AN5/C1IN3-/C2IN3-/PGM — Bidirectional I/O / Analog input / Comparator input / LVP programming |
| Pin 21 | RB2/AN4/C1IN2+/ZCD1OUT — Bidirectional I/O / Analog input / Comparator input / Zero Cross Detect output |
| Pin 22 | RB1/AN3/C1IN1-/C2IN1-/OPA1OUT — Bidirectional I/O / Analog input / Comparator input / Op-amp 1 output |
| Pin 23 | RB0/AN2/C1IN0+/C2IN0+/CCP1/INT — Bidirectional I/O / Analog input / Comparator input / CCP1 PWM / External interrupt |
| Pin 24 | VDD — Positive supply voltage (1.8V to 5.5V) |
| Pin 25 | VSS — Ground reference |
| Pin 26 | RD7/AN21 — Bidirectional I/O / Analog input |
| Pin 27 | RD6/AN20 — Bidirectional I/O / Analog input |
| Pin 28 | RD5/AN19/CCP2 — Bidirectional I/O / Analog input / CCP2 PWM |
Aplicaciones típicas
PIC16F1713T-I/SS es adecuado para 7 aplicacións: Constant-Current LED Lighting Driver, Battery-Powered IoT Sensor Node, Small Motor Control (Fans / Pumps), Home Appliance Control (White Goods), Sensor Signal Conditioning, Switch-Mode Power Supply (SMPS) Auxiliary Controller, Automotive Body and Interior Modules.
Constant-Current LED Lighting Driver
The PIC16F1713T-I/SS is well matched to closed-loop constant-current LED drivers because its integrated op-amp (trans-impedance amplifier), 8-bit DAC (setpoint reference), 10-bit ADC (current sense), and Zero Cross Detect peripheral combine into a single-chip driver with no external analog components. The 32MHz CPU provides headroom for PWM dimming and color-mixing algorithms, while the CLC peripheral can implement hardware-based analog dimming without CPU intervention. Compared to discrete LED driver ICs, this MCU variant reduces BOM count by 4-6 parts. The XLP sleep mode also supports battery-backed emergency LED fixtures where standby current below 50 nA extends shelf life. Use it in architectural lighting, strip lighting, and signage.
Recomendado
Battery-Powered IoT Sensor Node
For battery-powered wireless sensor nodes, the PIC16F1713T-I/SS delivers a strong combination of XLP sleep current (typical <50 nA with RTC running), 1.8V-5.5V supply range (direct Li-ion / 2xAA compatibility), and on-chip op-amps for direct sensor interfacing. The 10-bit ADC with 17 channels handles multi-sensor inputs (temperature, light, humidity), while the integrated DAC and PWM can drive buzzers or status LEDs without external components. The CLC and NCO peripherals can wake the CPU on analog threshold crossings or precise timing events, enabling years of battery life in coin-cell applications like utility meters, environmental loggers, and wearable health patches.
Recomendado
Small Motor Control (Fans / Pumps)
The PIC16F1713T-I/SS suits small BLDC or brushed DC motor control through its 2 CCP/PWM channels, 10-bit ADC for back-EMF or current sensing, on-chip op-amp for current-shunt amplification, and CLC + NCO for hardware commutation timing. Operating at 32MHz the CPU easily runs sensorless back-EMF zero-cross detection or PID speed loops at PWM rates up to 20 kHz. The ZCD peripheral simplifies AC-line synchronized motor start-up, and PPS allows remapping of PWM outputs to optimize PCB routing. Applications include 12V/24V brushless fans, small water pumps, and appliance blowers where integration removes external gate drivers and op-amps.
Recomendado
Home Appliance Control (White Goods)
For white-goods control boards (coffee machines, washing machines, induction cooktops, microwave ovens), the PIC16F1713T-I/SS offers the analog integration needed for temperature sensing (10-bit ADC + op-amp), user-interface feedback (PWM buzzer / LED + 8-bit DAC), and mains Zero Cross Detect (ZCD) for triac firing without extra hardware. The 1.8V-5.5V supply covers 3.3V logic and 5V analog rails in the same chip. Industrial temperature range (-40C to +85C) handles under-cabinet appliance environments. PPS lets designers remap peripherals to optimize PCB routing for compact control boards, and the 28-SSOP footprint fits in space-constrained designs.
Recomendado
Sensor Signal Conditioning
The PIC16F1713T-I/SS excels as a front-end signal conditioner for analog sensors (load cells, thermocouples, bridge-type pressure sensors). Its two integrated op-amps can form the instrumentation front-end, the 10-bit ADC digitizes the result, and the 8-bit DAC can drive sensor excitation or offset correction. The CLC peripheral implements digital filtering and threshold detection without CPU load, freeing the 32MHz core for higher-level tasks like calibration, linearization, and digital output formatting (I2C/SPI/UART). Combined with EUSART and I2C/SPI, this part replaces a dedicated signal-chain plus microcontroller in weigh scales, industrial transmitters, and process-control loops.
Recomendado
Switch-Mode Power Supply (SMPS) Auxiliary Controller
As an auxiliary controller in SMPS designs, the PIC16F1713T-I/SS handles housekeeping tasks: monitoring input/output voltage via the 10-bit ADC, driving optocoupler feedback through PWM + op-amp, executing fault protection logic, and providing housekeeping UART/I2C telemetry. The NCO and COG peripherals can synthesize precise timing events for synchronous rectification control, while ZCD detects AC line zero-cross for valley-switching. With 7KB Flash the MCU has room for state-machine firmware implementing PSU fault handling and PMBus-style telemetry. The 28-SSOP package drops into tight secondary-side layouts.
Recomendado
Automotive Body and Interior Modules
For non-safety automotive body and interior modules (ambient lighting, seat controllers, mirror adjusters, HVAC blend doors), the PIC16F1713T-I/SSVAO variant offers AEC-Q100 qualification in the same 28-SSOP footprint as the industrial part. Integrated op-amps condition motor current and temperature sensors, the 10-bit ADC reads multiple analog inputs, and PWM outputs drive small DC motors or LED strings. EUSART / LIN-compatible serial supports body-domain communication. Compared to dedicated automotive ASSPs, this MCU variant provides firmware-defined flexibility while retaining AEC-Q100 reliability.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PIC16F1713T-I/SS — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PIC16F1713-I/SS | PIC16F1713-E/SS | PIC16F1716-I/SS | PIC16F1709-I/SS | PIC16F1713T-I/SSVAO |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Flash Memory | 7 KB (4K x 14) | 7 KB | 7 KB | 14 KB (+100%) | 3.5 KB (-50%) | 7 KB |
| RAM | 512 B | 512 B | 512 B | 1 KB (+100%) | 256 B (-50%) | 512 B |
| Max CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Op-Amps / DAC / CLC / ZCD | 2 / 5+8-bit / Yes / Yes | 2 / 5+8-bit / Yes / Yes | 2 / 5+8-bit / Yes / Yes | 2 / 5+8-bit / Yes / Yes | 0 / 5-bit only / No / No | 2 / 5+8-bit / Yes / Yes |
| Temperature Grade | -40C to +85C (Industrial) | -40C to +85C | -40C to +125C (Extended) | -40C to +85C | -40C to +85C | -40C to +125C (Automotive) |
| AEC-Q100 Qualification | No (Industrial) | No | No (Extended temp only) | No | No | Yes (Automotive) |
Diferenciadores clave
- Highest analog integration in PIC16 mid-range family at 28 pins (frente a PIC16F1709-I/SS)
- Pin-compatible memory upgrade path to 14KB Flash (frente a PIC16F1716-I/SS)
- AEC-Q100 automotive grade variant in same footprint (frente a PIC16F1713T-I/SSVAO)
Notas de diseño
Place a 100nF decoupling capacitor as close as possible to the VDD pin (pin 24) of the 28-SSOP, with the trace to VDD kept short and wide. Add a bulk capacitor (1-10uF) within a few mm of the device. For noise-sensitive analog designs, split the analog VDD/VSS from digital VDD/VSS at the package with separate traces, and place a ferrite bead or small resistor between the analog and digital supplies to reduce digital switching noise on the analog rail feeding the op-amps and ADC.
Use Peripheral Pin Select (PPS) carefully. Map each peripheral output (PWM, USART TX, SPI clock) to the physical pin that minimizes trace crossings on the PCB, but lock the mapping early in design - re-mapping mid-design often forces PCB respins. For PWM-driven loads, route the PWM output directly to the gate-driver or load with the shortest possible trace, and keep analog feedback traces (current shunt, op-amp output) away from PWM edges to avoid capacitive coupling noise.
The on-chip op-amps have a limited input common-mode range and output swing that depends on VDD; at 3.3V supply the op-amp output cannot reach the rails. For rail-to-rail behavior, supply the device at 5V or use an external op-amp. Also note that the ZCD output on RB2 is multiplexed with analog AN4; ensure the PPS mapping does not conflict with the analog signal you need. Finally, the I2C pins (RC3/RC4) require external pull-ups (typically 4.7k at 100 kHz, 2.2k at 400 kHz) since the PIC16F1713T-I/SS does not include internal I2C pull-ups.
When using the 10-bit ADC, average multiple samples (typically 16x or 64x) to reach effective >12-bit resolution; this is especially important for the on-chip op-amp driving the ADC, where settling time and ADC acquisition time interact. Use the ADC dedicated clock derived from a low-jitter source (e.g., FRC with ADC dedicated oscillator) for best linearity. For PWM signals controlling inductive loads, add a small RC snubber or Schottky flyback diode close to the load to suppress ringing that can couple into the analog inputs.
Estimated: at 32MHz CPU and 5.5V supply with all peripherals active, the PIC16F1713T-I/SS draws approximately 5-7 mA; at 1.8V / 32MHz the same workload drops to ~2 mA. Sleep current with WDT disabled is <50 nA typical. For battery designs, use the XLP sleep modes (DOZE, PMD, Low-Power Sleep) aggressively, and gate unused peripherals via the PMD register. A coin cell (CR2032, ~220 mAh) can power the device in sleep with periodic sensor wake-ups for over 5 years.
Información de cumplimiento
RoHS compliant per Microchip product page. The PIC16F1713T-I/SS is the industrial grade (non-automotive); for AEC-Q100 use the VAO suffix variant (PIC16F1713T-I/SSVAO). MSL rating not explicitly stated in the verified data - see _validation_note.
