PIC16F1779-E/ML - 28KB Flash 8-bit MCU, 44-QFN | Microchip
N.º de pieza: PIC16F1779-E/ML ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $4.2 | $4,20 |
| 10 | $3.78 | $37,80 |
| 100 | $3.32 | $332,00 |
| 500 | $2.91 | $1.455,00 |
| 1.000 | $2.55 | $2.550,00 |
PIC16F1779-E/ML Descripción general
The PIC16F1779 belongs to the broader category of 8-bit RISC microcontrollers (MCU). An 8-bit MCU executes instructions on 8-bit-wide data paths and is widely used in cost-sensitive embedded designs where deterministic GPIO control, low power consumption, and rich on-chip analog integration outweigh the need for higher CPU throughput. The PIC16F1779 family sits at the upper end of Microchip's PIC16 mid-range line, where intelligent analog peripherals allow designers to implement closed-loop SMPS, LED drivers, motor commutation, and battery charging without external analog ICs.
Key features include 100 mA high-current I/O pins, Peripheral Pin Select (PPS) for flexible signal routing, SPI/I2C and EUSART serial interfaces, 10/16-bit PWMs with independent time bases, four operational amplifiers, 10-bit DAC, and core-independent peripherals (CIPs) that operate without CPU intervention. The -E suffix denotes an extended operating temperature range of -40C to +125C, while /ML identifies the 44-pin QFN package.
Architecturally, the PIC16F1779 uses a modified Harvard RISC core with a 14-bit instruction word, providing deterministic interrupt latency and a single-cycle instruction execution at 32 MHz (8 MIPS). On-chip peripherals are interconnected through Microchip's PPS fabric and signal routing matrix, enabling the COG, PWM, comparator, and op-amp outputs to drive each other and the GPIO ports with minimal CPU load, which simplifies real-time control firmware.
Typical applications include LED lighting drivers, switch-mode power supply (SMPS) digital control, battery charging systems, BLDC/PMSM motor control, and general-purpose industrial automation. The high 100 mA I/O sink/source capability allows direct drive of power MOSFETs, opto-isolators, and relay coils without external buffers.
When designing with this MCU, allocate the 28 KB Flash budget across bootloader, application, and EEPROM emulation regions early in firmware planning. The PPS matrix must be locked at runtime if any pin is reassigned to avoid glitches, and unused high-current I/O pins should be configured as outputs driving low to minimize quiescent current.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet.
Alternativas directas para PIC16F1779-E/ML — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PIC16F1779-E/ML (mismo factor de forma y huella) — difiere en Package, DAC, Operating Temperature, Program Memory (Flash), ADC.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
PIC16F1779-I/ML
✅ Sustitución directa✓ En stock
$3.04 / unidad
Ver hoja de datos →PIC16F1778-I/ML
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
PIC16F1769-I/ML
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$1.62 / unidad
Ver hoja de datos →PIC16F1768-I/ML
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$1.55 / unidad
Ver hoja de datos →PIC16F1719-I/ML
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
PIC16F1527-I/PT
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$3.25 / unidad
Ver hoja de datos →PIC16F1779-E/ML Valores máximos y características eléctricas
| Core Processor | PIC |
| Core Size | 8-bit |
| Program Memory Size | 28 KB (16K x 14) Flash |
| RAM Size | 2 KB |
| Frecuencia de reloj máxima | 32 MHz |
| Instruction Set | PIC16 (14-bit instruction word) |
| Data Converters | A/D 12x10b; D/A 1x10b |
| Encapsulado | 44-QFN (8x8 mm) |
| Rango de temperatura de funcionamiento | -40C to +125C |
| Tensión de alimentación | 2.3 V to 5.5 V |
| I/O Pins | 36 (with 100 mA high-current capability) |
| Peripherals | Brown-out Detect, PWM, WDT, OpAmp, Comparator, ZCD, PRG, COG, PPS |
| Connectivity | I2C, SPI, EUSART |
| PWM Resolution | 10/16-bit |
| Tipo de montaje | Surface Mount |
| Nivel MSL | 3 (168 hours) |
| Estado RoHS | Compliant |
Configuración de pines de PIC16F1779-E/ML
| Pin 1 | RA5/SS/HLVDIN/VCAP — GPIO / SPI slave select / high/low-voltage detect input / regulator output cap |
| Pin 2 | RA4/AN4/CPS4/T0CKI — GPIO / analog input 4 / cap touch 4 / Timer0 clock |
| Pin 3 | RA3/AN3/CPS3/Vref+/MDCARL — GPIO / analog input 3 / Vref+ / COG modulation carrier low |
| Pin 4 | RA2/AN2/CPS2/Vref-/MDCARH — GPIO / analog input 2 / Vref- / COG modulation carrier high |
| Pin 5 | RA1/AN1/CPS1/MDSRC — GPIO / analog input 1 / COG modulation source |
| Pin 6 | RA0/AN0/CPS0/MDOUT — GPIO / analog input 0 / COG modulation output |
| Pin 7 | VSS — Ground reference |
| Pin 8 | RA7/OSC1/CLKIN — GPIO / crystal oscillator input / external clock input |
| Pin 9 | RA6/OSC2/CLKOUT — GPIO / crystal oscillator output / clock output |
| Pin 10 | RC0/SOSCO — GPIO / secondary oscillator output |
| Pin 11 | RC1/SOSCI — GPIO / secondary oscillator input |
| Pin 12 | RC2/AN12/CPS12 — GPIO / analog input 12 |
| Pin 13 | RC3/AN13/CPS13 — GPIO / analog input 13 |
| Pin 14 | RC4/AN14/CPS14 — GPIO / analog input 14 |
| Pin 15 | RC5/AN15/CPS15 — GPIO / analog input 15 |
| Pin 16 | RC6/AN16/CPS16 — GPIO / analog input 16 |
| Pin 17 | RC7/AN17/CPS17 — GPIO / analog input 17 |
| Pin 18 | RD0 — GPIO port D bit 0 |
| Pin 19 | RD1 — GPIO port D bit 1 |
| Pin 20 | RD2 — GPIO port D bit 2 |
| Pin 21 | RD3 — GPIO port D bit 3 |
| Pin 22 | RD4 — GPIO port D bit 4 |
| Pin 23 | RD5 — GPIO port D bit 5 |
| Pin 24 | RD6 — GPIO port D bit 6 |
| Pin 25 | RD7 — GPIO port D bit 7 |
| Pin 26 | VSS — Ground reference |
| Pin 27 | VDD — Positive supply voltage |
| Pin 28 | RE0/AN5 — GPIO / analog input 5 |
| Pin 29 | RE1/AN6 — GPIO / analog input 6 |
| Pin 30 | RE2/AN7 — GPIO / analog input 7 |
| Pin 31 | RE3/MCLR/Vpp — GPIO / master clear reset / programming voltage |
| Pin 32 | RB0/AN8/CPS8/CCP4 — GPIO / analog input 8 / CCP4 PWM |
| Pin 33 | RB1/AN9/CPS9/PWM5 — GPIO / analog input 9 / 16-bit PWM5 |
| Pin 34 | RB2/AN10/CPS10/PWM6 — GPIO / analog input 10 / 16-bit PWM6 |
| Pin 35 | RB3/AN11/CPS11/PWM7 — GPIO / analog input 11 / 16-bit PWM7 |
| Pin 36 | RB4/SDA1/SDI1 — GPIO / I2C1 data / SPI1 data in |
| Pin 37 | RB5/SCL1/SCK1 — GPIO / I2C1 clock / SPI1 clock |
| Pin 38 | RB6/TX/CK — GPIO / EUSART TX / EUSART clock |
| Pin 39 | RB7/RX/DT — GPIO / EUSART RX / EUSART data |
| Pin 40 | VSS — Ground reference |
| Pin 41 | VDD — Positive supply voltage |
| Pin 42 | RF0 — GPIO port F bit 0 |
| Pin 43 | RF1 — GPIO port F bit 1 |
| Pin 44 | EP — Exposed thermal pad - connect to VSS for thermal dissipation |
Aplicaciones típicas
PIC16F1779-E/ML es adecuado para 6 aplicacións: Switch-Mode Power Supply (SMPS) Digital Control, BLDC and PMSM Motor Control, LED Lighting Drivers and Dimmers, Battery Charging and Power Management, Industrial Sensor Signal Conditioning, Automotive Body and Lighting ECUs.
Switch-Mode Power Supply (SMPS) Digital Control
The PIC16F1779-E/ML's on-chip op-amps, 10-bit DAC, 16-bit PWM, and zero-cross detect enable a fully digital peak-current-mode controller for isolated and non-isolated DC-DC converters. The op-amp closes the current-sense loop, the 16-bit PWM with 7.8 ns resolution drives the synchronous MOSFET gate driver, and the COG module adds programmable dead-time insertion without CPU overhead. The 100 mA I/O directly drives low-side gate drivers, eliminating external buffers. Combined with the 32 MHz / 8 MIPS core, this allows 500 kHz switching frequency control loops with less than 20% CPU utilization, leaving headroom for housekeeping and PMBus telemetry over I2C or EUSART.
Recomendado
BLDC and PMSM Motor Control
The PIC16F1779-E/ML drives sensorless BLDC and PMSM motors through the integrated Complementary Output Generator (COG), 16-bit PWM, ZCD for back-EMF sensing, and four op-amps that condition the current-sense shunt signals. The COG produces complementary 3-phase PWM with hardware dead-band insertion in as little as 8 ns, while the 100 mA I/O sinks/source directly into gate-driver opto-isolators or low-side drivers. PPS lets the firmware reassign PWM channels to any GPIO, simplifying PCB routing on multi-axis drives. The -40C to +125C extended temperature grade supports under-hood automotive and industrial fan/pump deployments.
Recomendado
LED Lighting Drivers and Dimmers
The PIC16F1779-E/ML is well suited to high-brightness LED drivers, using the 10-bit DAC to set constant-current references and the 16-bit PWM to dim with 16-bit resolution (>15 bits effective at 1 kHz). The op-amps sense high-side or low-side shunt current, while the COG generates the complementary buck/boost FET timing. The 100 mA I/O pins drive logic-level MOSFETs directly for sub-100 W luminaires. PPS allows the designer to map PWM, DAC, and comparator outputs to any pin during PCB layout, easing mechanical integration. The 2 KB RAM supports full DALI-2 or DMX-512 protocol stacks for professional lighting fixtures.
Recomendado
Battery Charging and Power Management
Lithium-ion battery chargers and uninterruptible power supplies benefit from the PIC16F1779-E/ML's integrated 10-bit ADC (12 channels), 10-bit DAC, op-amp current sense, and 16-bit PWM. The device executes CC/CV charge profiles with sub-1% current regulation by combining hardware PWM current-mode control with periodic ADC calibration. The 36 GPIOs handle multi-cell balancing FETs, thermistor inputs, SMBus/I2C communication, and charger-inhibit signalling. The extended -40C to +125C temperature grade enables outdoor energy-storage installations and electric vehicle supply equipment where ambient temperatures exceed 85C.
Recomendado
Industrial Sensor Signal Conditioning
The PIC16F1779-E/ML combines four on-chip op-amps, a 10-bit DAC, and a 12-channel 10-bit ADC to perform analog signal conditioning for bridge sensors, thermocouples, RTDs, and 4-20 mA current loops. The op-amps provide fixed-gain instrumentation amplification before digitization, while the 10-bit DAC trims sensor offsets in real time. The 36 GPIOs read end-of-travel limit switches and drive indicator LEDs. PPS routes SPI/I2C to any combination of pins, simplifying PCB routing for dense sensor hubs. The extended temperature grade and 100 mA I/O capability make it suitable for harsh factory-floor instrumentation.
Recomendado
Automotive Body and Lighting ECUs
The PIC16F1779-E/ML targets automotive body controllers, HVAC actuators, interior/exterior lighting, and LIN-slave nodes. The -E extended temperature grade ensures operation from -40C to +125C in cabin and engine-bay environments. The 100 mA high-current I/O drives power MOSFETs, relays, and LED strings directly, while the 16-bit PWM supports smooth fade-in/fade-out dimming with hardware dead-time insertion through COG. EUSART and I2C implement LIN 2.x slave stacks. Compared with Q-Grade automotive parts, the -E temperature grade provides the same silicon die at a lower cost for non-safety body applications.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PIC16F1779-E/ML — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PIC16F1779-I/ML | PIC16F1778-I/ML | PIC16F1769-I/ML | PIC16F1719-I/ML | PIC16F1527-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-QFN (8x8 mm) | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same |
| Flash Memory | 28 KB | 28 KB | 28 KB | 14 KB | 28 KB | 28 KB |
| RAM Size | 2 KB | 2 KB | 2 KB (reduced) | 1 KB | 2 KB | 1.5 KB |
| Max Clock Frequency | 32 MHz (8 MIPS) | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 20 MHz |
| Operating Temperature | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| COG / PRG / ZCD | Yes (all three) | Yes | Yes | Yes | No | No |
| Operational Amplifiers | 4 | 4 | 3 | 2 | 2 | 0 |
| 100 mA High-Current I/O | Yes | Yes | Yes | Yes | Yes | No |
| Unit Price (qty 100, USD, as of 2026-09-20) | 3.32 | 3.10 | 3.20 | 2.85 | 3.00 | 2.65 |
Diferenciadores clave
- Extended -40C to +125C operating temperature grade with same die as PIC16F1779-I/ML (frente a PIC16F1779-I/ML)
- Full Intelligent Analog suite (COG, PRG, ZCD, 4 op-amps) versus reduced analog on PIC16F1719 (frente a PIC16F1719-I/ML)
- Higher 32 MHz / 8 MIPS throughput versus 20 MHz on PIC16F1527 (frente a PIC16F1527-I/PT)
Notas de diseño
Place a 1 uF X7R ceramic bypass capacitor within 5 mm of each VDD pin (pins 27 and 41) and a 10 uF bulk capacitor on the same VDD rail. The PIC16F1779-E/ML's internal voltage regulator requires a 1 uF low-ESR capacitor on the VCAP pin (pin 1). Estimated: at 32 MHz with all peripherals active, the core draws approximately 8 mA; with all GPIOs as inputs and PPS unlocked, add 2-4 mA. Use sleep mode (1 uA typical) for battery-powered sensor applications and wake via WDT or interrupt.
Solder the exposed thermal pad (pin 44) directly to a continuous VSS copper pour of at least 25 mm^2 to keep junction temperature below 100C in enclosed industrial housings. Keep analog signal traces (ANx, op-amp inputs) at least 3 mm away from PWM switching traces and route them over a continuous ground pour to minimize crosstalk into the 10-bit ADC. Use a 4-layer PCB stack-up with dedicated ground and power planes for switching power designs where the PIC16F1779-E/ML drives high-current MOSFETs.
When using the Peripheral Pin Select (PPS) matrix, lock the PPS registers after configuration to prevent runaway writes that could remap peripherals to invalid pins. Do not enable the 100 mA high-current I/O pins as inputs without external current-limiting resistors, as the input structure is not rated for high-current source. The MCLR pin (pin 31) requires a 10 kohm pull-up to VDD if not used as a reset; floating MCLR causes unpredictable resets in noisy motor-control environments.
Estimated: at 32 MHz with four op-amps, COG, two PWMs, and ADC continuously active, the PIC16F1779-E/ML dissipates approximately 120 mW (24 mA at 5 V). With a 44-QFN junction-to-ambient thermal resistance of approximately 28 C/W on a JEDEC EIA/JESD51 4-layer test board, the temperature rise above ambient is approximately 3.4 C, keeping the junction well below the +125C extended limit. In sealed enclosures without airflow, derate clock frequency to 8 MHz (16 MIPS effective via PLL alternative parts) to maintain margin.
Información de cumplimiento
RoHS and REACH compliance per Microchip material declaration. The PIC16F1779-E/ML itself is not AEC-Q100 qualified (only the -EQ automotive suffix parts are); the -E temperature grade extends to +125C but does not constitute automotive qualification.