PIC18LF6585-I/PT - 8-Bit 40MHz MCU 48KB Flash ECAN | Microchip
N.º de pieza: PIC18LF6585-I/PT ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $8.1 | $8,10 |
| 10 | $7.45 | $74,50 |
| 100 | $6.72 | $672,00 |
| 500 | $5.98 | $2.990,00 |
| 1.000 | $5.31 | $5.310,00 |
PIC18LF6585-I/PT Descripción general
A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), data memory (RAM), and a rich set of peripheral blocks (timers, ADC, communication controllers, I/O). The PIC18F family sits in the 8-bit RISC tier of Microchip's portfolio and is widely adopted in automotive node, industrial control, and consumer applications where deterministic behavior and long product lifetimes matter.
Key features of the PIC18LF6585-I/PT include 48 KB of Flash program memory organized as 24K x 16 words, 3,328 bytes of RAM, an 8-channel 10-bit ADC, two analog comparators, two CCP modules, an Enhanced CAN 2.0B controller, and up to 52 digital I/O pins. The CPU core runs up to 40 MHz at 3.3V, with on-chip oscillator options and four programmable edge-triggered interrupt sources. The integrated ECAN peripheral supports CAN 2.0B active/passive and listens-only modes, device net filtering, and bit rates up to 1 Mbps.
The architecture is built around a Harvard RISC core with a 16-bit instruction word, an 8-bit data path, hardware multiply, and a vectored interrupt controller. The instruction pipeline and 32-level hardware stack deliver deterministic interrupt latency suitable for real-time CAN and control loops.
Typical applications include CAN-based industrial automation nodes, automotive body and chassis ECUs (non-safety critical), building automation HVAC controllers, sensor aggregation hubs, and low-power remote telemetry units. When designing with this part, pay attention to the decoupling network around VDD/VSS pairs, route the ECAN TX/RX lines as a matched differential pair, and program the CONFIG words at the top of Flash to lock oscillator, watchdog, and brown-out settings.
Alternativas directas para PIC18LF6585-I/PT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PIC18LF6585-I/PT (mismo factor de forma y huella) — difiere en Package, ADC, Core Architecture, Timers, I/O Pins.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
PIC18F6585-I/PT
✅ Sustitución directa✓ En stock
$6.95 / unidad
Ver hoja de datos →PIC18LF6685-I/PT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PIC18LF8585-I/PT
✅ Sustitución directa✓ En stock
$6.2 / unidad
Ver hoja de datos →PIC18LF4685-I/PT
✅ Sustitución directa✓ En stock
$5.55 / unidad
Ver hoja de datos →PIC18LF6525T-I/PT
✅ Sustitución directa✓ En stock
$5.95 / unidad
Ver hoja de datos →PIC18LF6585-I/PT Valores máximos y características eléctricas
| Core Architecture | 8-bit PIC18F RISC |
| Program Memory (Flash) | 48 KB (24K x 16 words) |
| Data Memory (RAM) | 3,328 bytes |
| Maximum CPU Frequency | 40 MHz |
| Operating Voltage Range | 2.0 V to 3.3 V (LF core) |
| I/O Pins | 52 |
| ADC | 8-channel, 10-bit |
| Analog Comparators | 2 |
| CCP Modules | 2 |
| CAN Controller | ECAN 2.0B active/passive |
| Encapsulado | 64-TQFP (PT) 10x10 mm |
| Temperatura de funcionamiento | -40 C to +85 C (Industrial) |
| Tipo de montaje | Surface Mount |
| Estado RoHS | Compliant |
Configuración de pines de PIC18LF6585-I/PT
| Pin 1 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| Pin 2 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| Pin 3 | RA2/AN2/VREF- — PORTA bit 2 / Analog input 2 / ADC VREF- |
| Pin 4 | RA3/AN3/VREF+ — PORTA bit 3 / Analog input 3 / ADC VREF+ |
| Pin 5 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pin 6 | RA5/AN4 — PORTA bit 5 / Analog input 4 |
| Pin 7 | RA6/OSC2 — PORTA bit 6 / Oscillator output |
| Pin 8 | RA7/OSC1 — PORTA bit 7 / Oscillator input |
| Pin 9 | VDD — Positive supply (2.0V-3.3V) |
| Pin 10 | VSS — Ground |
| Pin 11 | RB0/INT0 — PORTB bit 0 / External interrupt 0 |
| Pin 12 | RB1/INT1 — PORTB bit 1 / External interrupt 1 |
| Pin 13 | RB2/INT2 — PORTB bit 2 / External interrupt 2 |
| Pin 14 | RB3/INT3 — PORTB bit 3 / External interrupt 3 |
| Pin 15 | RB4 — PORTB bit 4 |
| Pin 16 | RB5 — PORTB bit 5 |
| Pin 17 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Pin 18 | RB7/PGD — PORTB bit 7 / ICSP data |
| Pin 19 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock |
| Pin 20 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| Pin 21 | RC2/CCP1 — PORTC bit 2 / CCP1 |
| Pin 22 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Pin 23 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Pin 24 | RC5/SDO — PORTC bit 5 / SPI data out |
| Pin 25 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| Pin 26 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| Pin 27 | RD0/C1IN+ — PORTD bit 0 / Comparator 1 non-inverting input |
| Pin 28 | RD1/C1IN- — PORTD bit 1 / Comparator 1 inverting input |
| Pin 29 | RD2/C2IN+ — PORTD bit 2 / Comparator 2 non-inverting input |
| Pin 30 | RD3/C2IN- — PORTD bit 3 / Comparator 2 inverting input |
| Pin 31 | RD4 — PORTD bit 4 |
| Pin 32 | RD5 — PORTD bit 5 |
| Pin 33 | RD6 — PORTD bit 6 |
| Pin 34 | RD7 — PORTD bit 7 |
| Pin 35 | RE0/RD/AN5 — PORTE bit 0 / Read / Analog input 5 |
| Pin 36 | RE1/WR/AN6 — PORTE bit 1 / Write / Analog input 6 |
| Pin 37 | RE2/CS/AN7 — PORTE bit 2 / Chip select / Analog input 7 |
| Pin 38 | VDD — Positive supply (2.0V-3.3V) |
| Pin 39 | VSS — Ground |
| Pin 40 | CANTX — ECAN transmit output |
| Pin 41 | CANRX — ECAN receive input |
| Pin 42 | RF0 — PORTF bit 0 |
| Pin 43 | RF1 — PORTF bit 1 |
| Pin 44 | RF2 — PORTF bit 2 |
| Pin 45 | RF3 — PORTF bit 3 |
| Pin 46 | RF4 — PORTF bit 4 |
| Pin 47 | RF5 — PORTF bit 5 |
| Pin 48 | RF6 — PORTF bit 6 |
| Pin 49 | RF7 — PORTF bit 7 |
| Pin 50 | RG0 — PORTG bit 0 |
| Pin 51 | RG1 — PORTG bit 1 |
| Pin 52 | RG2 — PORTG bit 2 |
| Pin 53 | RG3 — PORTG bit 3 |
| Pin 54 | RG4 — PORTG bit 4 |
| Pin 55 | MCLR/VPP — Reset / Programming voltage |
| Pin 56 | VDD — Positive supply (2.0V-3.3V) |
| Pin 57 | VSS — Ground |
| Pin 58 | NC — Not connected (per datasheet) |
| Pin 59 | NC — Not connected (per datasheet) |
| Pin 60 | NC — Not connected (per datasheet) |
| Pin 61 | NC — Not connected (per datasheet) |
| Pin 62 | OSC1/CLKI — External oscillator input |
| Pin 63 | OSC2/CLKO — External oscillator output |
| Pin 64 | AVDD — Analog positive supply (2.0V-3.3V) |
Aplicaciones típicas
PIC18LF6585-I/PT es adecuado para 6 aplicacións: Industrial CAN Sensor Nodes, Automotive Body and Chassis ECUs, Building Automation HVAC Controllers, Low-Power Remote Telemetry Units, Motor Control Front-End Controllers, LED Lighting Control Nodes.
Industrial CAN Sensor Nodes
The PIC18LF6585-I/PT fits industrial CAN sensor nodes by combining on-chip ECAN 2.0B with 48 KB Flash and 3,328 bytes RAM. Placed at each sensor pod, the MCU aggregates ADC samples and streams them over the bus at up to 1 Mbps. The LF 2.0V-3.3V supply lets the design share a 3.3V rail with sensors and radios, while the 40 MHz core handles protocol overhead without offloading.
Recomendado
Automotive Body and Chassis ECUs
The PIC18LF6585-I/PT is widely used in non-safety automotive body and chassis ECUs thanks to its integrated ECAN, 52 I/O, and -40C to +85C industrial temperature grade. It drives lamp loads, mirror controls, and door modules while communicating over CAN to a central gateway. The 10-bit ADC reads position sensors and the 8-channel input handles multi-axis feedback within a compact 64-TQFP footprint.
Recomendado
Building Automation HVAC Controllers
The PIC18LF6585-I/PT suits building HVAC controllers that must communicate with rooftop units and air-handlers over CAN. The MCU's 48 KB Flash holds the BACnet/CAN gateway translation logic, while its 10-bit ADC reads temperature and humidity sensors. Industrial temperature rating and 52 I/O support multi-relay damper and valve control within a single MCU plus companion driver chips.
Recomendado
Low-Power Remote Telemetry Units
The PIC18LF6585-I/PT fits remote telemetry units where its LF 2.0V-3.3V core minimizes sleep current while the ECAN controller reports back to a gateway. Sleep current under 1 uA (with peripherals disabled) lets the unit run from small battery or solar sources. The 40 MHz active core wakes on CAN activity, processes payloads, and returns to sleep, with the 48 KB Flash storing local calibration data.
Recomendado
Motor Control Front-End Controllers
The PIC18LF6585-I/PT is used as a front-end controller for small brushed or stepper motor drives, providing CAN connectivity, sensor feedback via 10-bit ADC, and PWM generation through two CCP modules. The 64-TQFP package fits on compact PCBs alongside gate drivers and H-bridges, with the 52 I/O available for limit-switch inputs, encoder feedback, and fault signals.
Recomendado
LED Lighting Control Nodes
The PIC18LF6585-I/PT drives networked LED lighting controllers using ECAN to receive dimming commands from a central controller. PWM via CCP modules provides smooth dimming, and the 52 I/O handle multi-channel RGBW fixtures. Industrial temperature rating suits outdoor luminaires, while 3.3V operation simplifies co-design with constant-current LED drivers that share the same supply rail.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PIC18LF6585-I/PT — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PIC18F6585-I/PT | PIC18LF6685-I/PT | PIC18LF8585-I/PT | PIC18LF4685-I/PT | PIC18LF6525T-I/PT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (PT) 10x10 mm | 64-TQFP (PT) - same | 64-TQFP (PT) - same | 64-TQFP (PT) - same | 64-TQFP (PT) - same | 64-TQFP (PT) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Flash | 48 KB | 48 KB | 96 KB | 96 KB | 96 KB | 48 KB |
| RAM | 3,328 bytes | 3,328 bytes | 7,168 bytes | 3,328 bytes | 3,328 bytes | 2,048 bytes |
| Operating Voltage | 2.0V to 3.3V (LF) | 4.2V to 5.5V (F) | 2.0V to 3.3V (LF) | 2.0V to 3.3V (LF) | 2.0V to 3.3V (LF) | 2.0V to 3.3V (LF) |
| ECAN 2.0B | Yes | Yes | Yes | Yes | No | No |
| Max CPU Frequency | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| I/O Pins | 52 | 52 | 52 | 52 | 52 | 52 |
Diferenciadores clave
- Integrated Enhanced CAN 2.0B controller with DeviceNet filtering (frente a PIC18LF4685-I/PT)
- 2.0V-3.3V low-voltage LF core for battery-powered designs (frente a PIC18F6585-I/PT)
- Compact 64-TQFP 10x10 mm package with 52 I/O (frente a PIC18LF4585-I/PT)
Notas de diseño
Place a 100 nF ceramic decoupling capacitor as close as possible to each VDD/VSS pair of the PIC18LF6585-I/PT. Add a bulk 10 uF tantalum or ceramic capacitor at the supply entry. The LF core draws low sleep current, but the ECAN module wakes on bus activity; bulk capacitance prevents VDD droop during CAN TX bursts that may otherwise trigger brown-out reset.
Route the CANTX and CANRX lines as a matched differential pair with characteristic impedance of 120 ohm, terminated at the bus ends (not at the MCU). Keep the pair away from switching nodes such as the oscillator traces to preserve signal integrity. Route the 40 MHz primary oscillator traces short and guard them with a ground pour to minimize radiated EMI.
Always configure the MCLR pin with the proper pull-up and ensure the ICSP PGC/PGD lines (RB6/RB7) are not loaded by external circuitry that prevents in-circuit programming. The CONFIG words at the top of Flash must be programmed to disable watchdog, set the oscillator mode, and enable brown-out reset; failure to set these defaults may cause the part to lock up or run at an unexpected clock rate.
Información de cumplimiento
RoHS compliant per Microchip product page. AEC-Q100 qualification status not specified for the LF variant; automotive safety-critical designs should consider AEC-Q100 qualified PIC18 variants. Halogen-free status unknown from provided data.
