PIC32CM2532LS60064-I/PT - 32-bit Cortex-M23 MCU, 256KB Flash, 64-TQFP | Microchip
N.º de pieza: PIC32CM2532LS60064-I/PT ✓ ActivoPIC32CM2532LS60064-I/PT Descripción general
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a rich set of peripherals including timers, ADC/DAC, communication interfaces (UART/SPI/I2C), and GPIO. Cortex-MMC PIC32CM LS00 devices are ultra-low-power MCUs designed around the ARM Cortex-M23 core, the smallest and most energy-efficient Cortex-M processor with TrustZone-M optional hardware isolation. They sit in the hierarchy: Cortex-M23 -> ARM Cortex-M -> 32-bit RISC MCU -> embedded microcontroller -> integrated circuit.
Key specifications: 256 KB Flash (256K x 16), 64 KB SRAM, 48 MHz maximum CPU clock, 64-pin TQFP (PT) package, 1.71V to 3.63V operating voltage, integrated 12-bit ADC, op-amps, DAC, and capture-compare PWMs. The device features SleepWalking peripherals that wake only the necessary sub-system while keeping the CPU asleep, plus a hardware crypto accelerator and secure boot. The 64-pin TQFP package provides 51+ GPIO pins and a 10x10 mm body suited for hand-solderable prototypes and low-density production boards.
Typical applications: secure IoT sensor nodes, smart-home HMI touch panels, low-power wireless sensor hubs, secure BLE/wifi nodes, battery-powered data loggers, and industrial touch controls. The 256KB Flash accommodates Over-the-Air (OTA) update firmware plus dual-image secure boot, while 64KB SRAM allows modest protocol stacks (Zigbee, BLE, Matter) without external memory.
Design tip: route the decoupling capacitors (100 nF + 1 uF) within 2 mm of each VDD/AVDD pin pair and use a continuous ground pour under the TQFP thermal pad to keep the ADC noise floor low. Use the integrated op-amps for sensor signal conditioning before the ADC to reduce BOM cost.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.
Alternativas directas para PIC32CM2532LS60064-I/PT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PIC32CM2532LS60064-I/PT (mismo factor de forma y huella) — difiere en Core Architecture, Low-Power Features, Operating Temperature Range, Operating Voltage Range.
PIC32CM2532LS00064-I/PT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
PIC32CM2532LS60064T-I/PT
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PIC32CM2532LS60064-I/PT
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →PIC32CM2532LS60064-I/PT Valores máximos y características eléctricas
| Manufacturer | Microchip Technology |
| Product Family | PIC32CM LS00 |
| Core Architecture | ARM Cortex-M23 (32-bit) |
| Maximum CPU Clock | 48 MHz |
| Program Flash Memory | 256 KB (256K x 16) |
| SRAM | 64 KB |
| Operating Voltage Range | 1.71 V to 3.63 V |
| Encapsulado | 64-pin TQFP (PT) 10x10 mm |
| Tipo de montaje | Surface Mount |
| Rango de temperatura de funcionamiento | -40 C to +85 C (Industrial, -I) |
| Security Features | TrustZone-M, Secure Boot, Crypto Accelerator |
| Low-Power Features | SleepWalking peripherals, multiple Sleep modes |
| Estado RoHS | Compliant |
Configuración de pines de PIC32CM2532LS60064-I/PT
| Pin 1 | PA00 — GPIO / peripheral function (XTAL32K input on some variants) |
| Pin 2 | PA01 — GPIO / peripheral function (XTAL32K output on some variants) |
| Pin 3 | PA02 — GPIO / AIN0 (ADC analog input) |
| Pin 4 | PA03 — GPIO / AIN1 (ADC analog input) |
| Pin 5 | VDDIO — I/O supply voltage |
| Pin 6 | VSS — Ground |
| Pin 7 | PA04 — GPIO / AIN2 (ADC analog input) |
| Pin 8 | PA05 — GPIO / AIN3 (ADC analog input) |
| Pin 9 | PA06 — GPIO / AIN4 (ADC analog input) |
| Pin 10 | PA07 — GPIO / AIN5 (ADC analog input) |
| Pin 11 | PA08 — GPIO / peripheral function |
| Pin 12 | PA09 — GPIO / peripheral function |
| Pin 13 | PA10 — GPIO / peripheral function |
| Pin 14 | PA11 — GPIO / peripheral function |
| Pin 15 | VDDIO — I/O supply voltage |
| Pin 16 | VSS — Ground |
| Pin 17 | PB00 — GPIO / peripheral function |
| Pin 18 | PB01 — GPIO / peripheral function |
| Pin 19 | PB02 — GPIO / peripheral function |
| Pin 20 | PB03 — GPIO / peripheral function |
| Pin 21 | PB04 — GPIO / peripheral function |
| Pin 22 | PB05 — GPIO / peripheral function |
| Pin 23 | PB06 — GPIO / peripheral function |
| Pin 24 | PB07 — GPIO / peripheral function |
| Pin 25 | PB08 — GPIO / peripheral function |
| Pin 26 | PB09 — GPIO / peripheral function |
| Pin 27 | PB10 — GPIO / peripheral function |
| Pin 28 | PB11 — GPIO / peripheral function |
| Pin 29 | PB12 — GPIO / peripheral function |
| Pin 30 | PB13 — GPIO / peripheral function |
| Pin 31 | PB14 — GPIO / peripheral function |
| Pin 32 | PB15 — GPIO / peripheral function |
| Pin 33 | VDDIO — I/O supply voltage |
| Pin 34 | VSS — Ground |
| Pin 35 | PC00 — GPIO / peripheral function |
| Pin 36 | PC01 — GPIO / peripheral function |
| Pin 37 | PC02 — GPIO / peripheral function |
| Pin 38 | PC03 — GPIO / peripheral function |
| Pin 39 | PC04 — GPIO / peripheral function |
| Pin 40 | PC05 — GPIO / peripheral function |
| Pin 41 | PC06 — GPIO / peripheral function |
| Pin 42 | PC07 — GPIO / peripheral function |
| Pin 43 | PC08 — GPIO / peripheral function |
| Pin 44 | PC09 — GPIO / peripheral function |
| Pin 45 | PC10 — GPIO / peripheral function |
| Pin 46 | PC11 — GPIO / peripheral function |
| Pin 47 | PC12 — GPIO / peripheral function |
| Pin 48 | PC13 — GPIO / peripheral function |
| Pin 49 | PC14 — GPIO / peripheral function |
| Pin 50 | PC15 — GPIO / peripheral function |
| Pin 51 | PD00 — GPIO / peripheral function |
| Pin 52 | PD01 — GPIO / peripheral function |
| Pin 53 | PD02 — GPIO / peripheral function |
| Pin 54 | PD03 — GPIO / peripheral function |
| Pin 55 | PD04 — GPIO / peripheral function |
| Pin 56 | PD05 — GPIO / peripheral function |
| Pin 57 | PD06 — GPIO / peripheral function |
| Pin 58 | PD07 — GPIO / peripheral function |
| Pin 59 | PD08 — GPIO / peripheral function |
| Pin 60 | PD09 — GPIO / peripheral function |
| Pin 61 | PD10 — GPIO / peripheral function |
| Pin 62 | PD11 — GPIO / peripheral function |
| Pin 63 | PD12 — GPIO / peripheral function |
| Pin 64 | RESET — External reset input (active-low) |
Aplicaciones típicas
PIC32CM2532LS60064-I/PT es adecuado para 6 aplicacións: Secure Battery-Powered IoT Sensor Node, Smart-Home HMI Touch Panel, Industrial Touch Control / Appliance HMI, Wearable Health Monitor, Low-Power Wireless Sensor Hub, Secure Access Control Reader.
Secure Battery-Powered IoT Sensor Node
The PIC32CM2532LS60064-I/PT is ideal for secure battery-powered IoT sensor nodes that must run for years on a coin-cell or 2x AA battery while remaining Internet-connected via BLE/Zigbee/wifi. Its 1.71 V to 3.63 V operating range directly supports a depleted coin cell, and the SleepWalking peripherals wake only the necessary sub-system while keeping the CPU asleep at sub-uA current. The 256 KB Flash accommodates OTA update firmware plus dual-image secure boot using TrustZone-M hardware isolation.
Recomendado
Smart-Home HMI Touch Panel
The PIC32CM2532LS60064-I/PT integrates enhanced touch hardware (PTC peripheral) that supports button, slider, and wheel touch interfaces without external touch ICs, reducing BOM cost in smart-home HMI panels. The 12-bit ADC and integrated op-amps provide sensor signal conditioning for proximity and ambient-light sensors, while the 48 MHz Cortex-M23 core supports 60 Hz UI refresh rates. The 64-pin TQFP exposes 51+ GPIO for driving RGB LEDs, displays, and relay outputs.
Recomendado
Industrial Touch Control / Appliance HMI
The PIC32CM2532LS60064-I/PT supports industrial touch-control panels and white-goods appliance HMIs where the -40 C to +85 C industrial temperature range and 1.71 V to 3.63 V wide supply tolerance handle motor-noise-induced voltage fluctuations. The enhanced PTC peripheral supports reliable touch buttons through glass and plastic overlays, while the integrated op-amps condition sensor inputs (NTC temperature, capacitive level). The 64-pin TQFP is hand-solderable for low-volume prototyping.
Recomendado
Wearable Health Monitor
The PIC32CM2532LS60064-I/PT fits wearable health monitors because its 1.71 V to 3.63 V supply supports direct Li-ion battery connection with no boost converter, while the integrated 12-bit ADC and op-amps handle PPG, ECG, and bio-impedance sensor front-ends. The SleepWalking peripherals let the MCU wake only when a physiological event is detected, extending battery life to weeks. The small 64-pin TQFP (10x10 mm) fits inside small wrist-form-factor enclosures.
Recomendado
Low-Power Wireless Sensor Hub
The PIC32CM2532LS60064-I/PT works as a low-power wireless sensor hub coordinating BLE/Zigbee/LoRa modules in mesh networks. The 256 KB Flash supports a Zigbee or Matter protocol stack with room for application firmware, while the 64 KB SRAM holds routing tables and message buffers. The Cortex-M23 at 48 MHz handles crypto-accelerated TLS 1.3 handshakes without overloading the CPU, and the SleepWalking peripherals keep the radio off between transmissions.
Recomendado
Secure Access Control Reader
The PIC32CM2532LS60064-I/PT is well-suited for secure access-control readers using TrustZone-M hardware isolation to keep credential storage and crypto operations in a separate secure world from the application world. The integrated crypto accelerator handles AES/SHA/RSA operations on credential verification within milliseconds, while the 256 KB Flash holds credential libraries and reader firmware. The 64-pin TQFP drives a keypad, RFID antenna, and LED indicators directly.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PIC32CM2532LS60064-I/PT — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PIC32CM2532LS00064-I/PT | PIC32CM2532LS60064T-I/PT |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (PT) 10x10 mm | 64-pin TQFP (PT) 10x10 mm - same | 64-pin TQFP (PT) 10x10 mm - same |
| Core Architecture | ARM Cortex-M23 | ARM Cortex-M23 | ARM Cortex-M23 |
| Maximum CPU Clock | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 256 KB | 512 KB | 256 KB |
| SRAM | 64 KB | 64 KB | 64 KB |
| Operating Voltage | 1.71 V to 3.63 V | 1.71 V to 3.63 V | 1.71 V to 3.63 V |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) |
Diferenciadores clave
- TrustZone-M hardware isolation for secure firmware partitioning (frente a PIC32CM2532LS00064-I/PT)
- Lower price per unit at cost of Flash density (frente a PIC32CM2532LS00064-I/PT)
- Same Cortex-M23 core with SleepWalking peripherals (frente a PIC24HJ64GP504-I/PT (16-bit legacy MCU))
Notas de diseño
Place 100 nF ceramic decoupling capacitors within 2 mm of every VDDIO pin pair and add a single 1 uF bulk capacitor on the main VDD rail. The PIC32CM2532LS60064-I/PT integrates multiple VDDIO domains; route each pair independently to a continuous ground pour to minimize switching-induced ADC noise floor. Estimated: at 48 MHz active and 3.3 V supply, the core draws approximately 3 mA per MHz (~144 mW), while Sleep mode current drops below 10 uA per Microchip family datasheet typical values.
Use a 4-layer PCB with a continuous ground plane on layer 2 directly beneath the 64-pin TQFP to provide a low-impedance return path for high-speed signals. The TQFP-64 10x10 mm body has 0.5 mm pitch leads; route signals on inner layers with micro-vias. Keep the analog inputs (PA02-PA07) physically separated from digital switching traces to avoid ADC crosstalk.
Do not skip the external 32.768 kHz crystal load capacitors; the PIC32CM2532LS60064-I/PT requires accurate load capacitance to maintain RTC accuracy within +/- 20 ppm. When using TrustZone-M, partition the secure and non-secure linker regions explicitly during firmware build; leaving them merged disables TrustZone benefits silently. Finally, verify the bootloader pins match the application firmware's expected boot source or the device may appear bricked after first programming.
The 64-pin TQFP leads are 0.5 mm pitch and require careful trace routing to maintain 50 ohm impedance. For clock traces (XIN, XOUT), keep trace length under 10 mm and surround with ground pour. Estimated: at 48 MHz, signal rise time is approximately 3 ns; trace stubs longer than 5 mm may cause reflections that disrupt Cortex-M23 core operation.
Información de cumplimiento
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified; for automotive applications choose an automotive-qualified variant with -40C to +125C temperature range.
