SI3215-C-GM - Single-Channel SLIC/Codec | Silicon Labs
N.º de pieza: SI3215-C-GM ✓ ActivoSI3215-C-GM Descripción general
A Subscriber Line Interface Concept, or SLIC, is a telecom interface integrated circuit that connects a telephone line to a digital voice system. It combines voice conversion, line-current control, ring-signal generation, tone generation, and telephone-signaling functions. In the signal chain, the SI3215-C-GM sits between the analog subscriber line and a PCM, GCI, or SPI digital interface, reducing the need for separate line-interface circuitry.
Key features include software-programmable internal balanced ringing up to 90 VPK and support for up to 5 REN, subject to line-length and REN conditions. The device performs the BORSCHT functions required for subscriber-line supervision, while integrated DTMF generation supports telephone tone signaling. A 3.13 V to 5.25 V operating range accommodates both 3.3 V and 5 V system environments, while GCI, PCM, and SPI interfaces provide flexible connectivity to digital voice processors.
The SI3215-C-GM integrates a DC-DC converter and battery supply, allowing the device to supply line-side operating power without a separate high-voltage supply design. This architecture is intended for economical single-channel or low-channel-count voice systems. Programmable ringing and line parameters permit adaptation to different country requirements, including the Japan and China signaling requirements identified in the manufacturer datasheet.
Typical applications include subscriber-line access, voice-over-IP terminal equipment, digital loop carrier systems, voice gateways, embedded telephony controllers, and single-channel voice-processing boards. Its GCI, PCM, and SPI interfaces allow integration with a host processor, digital signal processor, or telephony application-specific circuit while retaining the required line-side functions in one package.
Designers should pay close attention to the exposed-pad thermal path, high-voltage line connections, bypass-capacitor placement, and the requirements of the integrated DC-DC converter. Use the manufacturer reference circuit and pin-description table to define component values and board clearances. Do not substitute normal low-voltage routing practices for the line-side isolation and clearance shown by the application design.
This page combines the SI3215-C-GM operating characteristics, interface options, replacement considerations, and practical implementation guidance in a form that supports initial component selection and board-layout planning. The manufacturer datasheet remains the controlling reference for final electrical limits, pin assignments, timing, and production design changes.
Alternativas directas para SI3215-C-GM — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con SI3215-C-GM (mismo factor de forma y huella) — difiere en Package, Power Dissipation, Product Type.
SI3215-C-FM
✅ Sustitución directaConsulte el precio
Ver hoja de datos →SI3215-C-GM Especificaciones
| Product Type | Single-channel SLIC/Codec |
| Number of Circuits | 1 channel |
| Supply Voltage Range | 3.13 V to 5.25 V |
| Typical Supply Current | 88 mA |
| Power Dissipation | 700 mW |
| Rango de temperatura de funcionamiento | -40 °C to +85 °C |
| Digital Interfaces | GCI, PCM, SPI |
| Programmable Internal Ringing | Up to 90 VPK |
| Maximum Ringing Load | 5 REN at 4 kft |
| Ringing Load at Longer Line Length | 3 REN at 8 kft |
| Telephone Functions | Integrated BORSCHT functions |
| Tone Generation | Integrated DTMF generation |
| Country-Specific Signaling | Supports Japan and China requirements |
| DC-DC Converter | Integrated |
| Battery Supply | Integrated |
| Encapsulado | 38-pin QFN, 5 mm x 7 mm |
| Tipo de montaje | Surface mount |
| Lead-Free Status | Lead-free |
Guía de configuración de pines de SI3215-C-GM 38-pin qfn, 5 mm x 7 mm
Configuración de pines para SI3215-C-GM (encapsulado 38-pin qfn, 5 mm x 7 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para SI3215-C-GM.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
SI3215-C-GM es adecuado para 6 aplicacións: Voice-over-IP Terminal Equipment, Digital Loop Carrier Terminal, Embedded Voice Gateway, Industrial Telephone Control Card, Analog Telephone Adapter, VoIP Network Interface Module.
Voice-over-IP Terminal Equipment
The SI3215-C-GM fits a Voice-over-IP terminal that connects an analog telephone line to a digital voice processor. Its GCI, PCM, and SPI interfaces provide several host-connection options, while the integrated BORSCHT functions, DTMF generation, and programmable ringing reduce the number of separate line-interface components. Operating from 3.13 V to 5.25 V permits use in both 3.3 V and 5 V equipment. The design must still provide suitable line protection, isolation, and connector surge handling, while the 38-pin QFN exposed pad needs a low-impedance thermal path.
Recomendado
Digital Loop Carrier Terminal
The SI3215-C-GM is appropriate for a low-channel digital loop carrier terminal requiring subscriber-line ringing and supervision. Its integrated converter can generate balanced ringing up to 90 VPK without requiring a separate high-voltage ringing supply, and the programmable line parameters support different deployment conditions. The listed ringing capability includes 5 REN at 4 kft and 3 REN at 8 kft, so designers should verify actual cable length and off-hook load. GCI or PCM connectivity allows the device to interface efficiently with a carrier-processing platform.
Recomendado
Embedded Voice Gateway
An embedded voice gateway can use the SI3215-C-GM to add a controlled analog line channel to an embedded processor platform. The codec's GCI, PCM, and SPI interfaces support flexible processor connections, while integration of line supervision, tone generation, battery supply, and the DC-DC converter simplifies the analog front end. Its 3.13 V to 5.25 V operating range supports common embedded supply rails. Firmware configuration must be reviewed carefully because ringing current, DC feed, and country-specific telephone behavior are programmable parts of the system design.
Recomendado
Industrial Telephone Control Card
The SI3215-C-GM suits an industrial telephone control card that must supervise a subscriber line and generate ring and DTMF signals. Its -40 °C to +85 °C operating range supports controlled industrial environments, and the 88 mA typical supply current provides a defined starting point for power budgeting. The integrated converter reduces the number of external high-voltage supply components, but it does not replace line-side protection. Engineers should follow the manufacturer reference circuit for magnetics, protection, bypass capacitors, and exposed-pad thermal construction.
Recomendado
Analog Telephone Adapter
The SI3215-C-GM can form the line-side core of an analog telephone adapter connected to a digital voice system. Programmable ringing up to 90 VPK, integrated BORSCHT supervision, DTMF generation, and multiple digital interfaces allow the adapter to provide more than basic voice conversion. The 3.13 V minimum supply voltage supports 3.3 V system architectures, while the 5.25 V maximum permits 5 V designs. Production evaluation should confirm country-specific line parameters, ringing margin, and firmware compatibility for the intended telephone network.
Recomendado
VoIP Network Interface Module
The SI3215-C-GM is suitable for a VoIP network interface module that must bridge an analog subscriber line and a digital packet-processing platform. PCM and SPI connectivity makes it adaptable to different processor architectures, while the integrated converter handles line-side power generation more compactly than a discrete discrete high-voltage design. Typical supply current is 88 mA, which must be considered alongside processor and network-interface loads on a shared power rail. The 38-pin QFN package supports compact designs, although proper thermal vias and controlled layout around the line-sense and switching nodes remain essential.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para SI3215-C-GM — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SI3215-C-FM |
|---|---|---|
| Product Type | Single-channel programmable SLIC/Codec | Single-channel legacy SLIC |
| Brand | Silicon Labs | Silicon Labs |
| Package | 38-pin QFN, 5 mm x 7 mm | 38-pin QFN |
| Number of Channels | 1 channel | 1 channel |
| Supply Voltage Range | 3.13 V to 5.25 V | 3.3 V/5 V |
| DC-DC Converter | Integrated | Integrated |
Diferenciadores clave
- Single-channel SLIC/codec integration (frente a SI3215-C-FM)
- Programmable balanced ringing (frente a SI3215-C-FM)
- Multiple digital host interfaces (frente a SI3215-C-FM)
Notas de diseño
Treat the exposed pad as the primary thermal and electrical connection for the 38-pin QFN. Use the manufacturer land pattern and recommended via arrangement, keep the pad connection short, and provide uninterrupted ground-plane area beneath the device. The listed 700 mW power value makes thermal-path design important in compact systems, particularly during repeated hook-state transitions or ringing. Confirm the final junction temperature against the latest manufacturer limits using the actual board construction and enclosure.
Follow the manufacturer reference circuit for input bypass, converter components, line-side networks, and protection placement. Place high-frequency bypass capacitors directly between the relevant supply and ground pins, with the shortest possible loop and minimal via inductance. Separate the high-energy subscriber-line routing from sensitive digital interface traces, and do not allow protection-device current to flow through signal or ground return paths intended for the codec.
Do not assume that the integrated DC-DC converter eliminates the need for telephone-network protection. The subscriber line requires suitable surge and overvoltage handling, and the board must satisfy the isolation or separation requirements of the intended network and regulatory environment. Also confirm the programmed ringing limit against the attached REN load and cable length; the SI3215-C-GM specifies 5 REN at 4 kft and 3 REN at 8 kft.
Budget the 3.13 V to 5.25 V supply for the typical 88 mA operating current plus transient margin during hook-state changes, converter startup, and ringing. Use the manufacturer power-conversion component values and loop layout rather than substituting generic inductors or capacitors. A shared 3.3 V rail can simplify the design, but the host processor, network interface, and line converter should be checked for startup sequencing and rail droop.
Información de cumplimiento
The SI3215-C-GM is identified as a lead-free device. RoHS, REACH, halogen-free, and conflict-minerals declarations were not stated in the available product information.