SIM7600CE-A - 4G LTE Cat-4 150Mbps Module | SIMCom
N.º de pieza: SIM7600CE-A ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $13.99 | $13,99 |
| 10 | $13.49 | $134,90 |
| 100 | $12.99 | $1.299,00 |
| 500 | $12.49 | $6.245,00 |
| 1.000 | $11.99 | $11.990,00 |
SIM7600CE-A Descripción general
A cellular module of this type is a self-contained RF transceiver system that implements the modem baseband, RF front-end, and protocol stack of an LTE network terminal. Within the system hierarchy, it sits between the antenna connector and the host application processor, communicating over AT commands or USB, and forms the connectivity layer of the power management and communications subsystem of an IoT or M2M device.
Key features include LTE Cat-4 peak throughput of 150 Mbps downlink / 50 Mbps uplink, backward compatibility with TD-SCDMA (384 Kbps downlink), HSPA+, EVDO, GSM/GPRS/EDGE, and integrated GNSS positioning (GPS + GLONASS + BeiDou). The compact 30 x 30 mm footprint makes it suitable for space-constrained industrial designs requiring both high-speed data and positioning.
Technically, the SIM7600 series implements a multi-mode modem supporting LTE-TDD/FDD, TD-SCDMA, CDMA/EVDO, and GSM bands, allowing seamless fallback to 2G/3G networks where LTE coverage is unavailable. Data transfer over USB, UART, and optional audio interfaces enables straightforward integration with microcontrollers and Linux-based hosts via standard AT command sets and dial-up networking.
Typical applications include industrial IoT gateways, vehicle tracking and telematics, smart metering backhaul, and security/camera systems that need reliable cellular data plus satellite positioning from a single module.
Design consideration: LTE Cat-4 transmitters draw burst currents above 2 A at peak power; the host power supply must provide a stable 3.3-4.2 V rail with low impedance and adequate bulk capacitance to avoid voltage drops during transmit bursts and network registration.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Alternativas directas para SIM7600CE-A — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con SIM7600CE-A (mismo factor de forma y huella) — difiere en Downlink Data Rate, GNSS, Interfaces, Mounting Type, RoHS Status.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
SIM7600CE
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SIM7600CE-T
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SIM7600CE-CNSE
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SIM7600E-H
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
SIM7600G-H
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$43.98 / unidad
Ver hoja de datos →Quectel EC21
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
Fibocom L610
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SIM7600CE-A Especificaciones (publicadas por el fabricante)
| Network Category | LTE Cat-4 |
| Downlink Data Rate | Up to 150 Mbps (LTE) |
| Uplink Data Rate | Up to 50 Mbps (LTE) |
| TD-SCDMA Downlink | Up to 384 Kbps |
| TD-SCDMA Uplink | Up to 128 Kbps |
| LTE-TDD Bands | B38/B39/B40/B41 |
| 3G Fallback | TD-SCDMA B34/B39, HSPA+, EVDO |
| 2G Fallback | GSM/GPRS/EDGE quad-band |
| GNSS | GPS + GLONASS + BeiDou |
| Dimensions | 30 x 30 x 2.9 mm |
| Package Type | LCC (SMD) |
| Interfaces | USB, UART, SIM, audio, GPIO |
| Tipo de montaje | Surface Mount (LCC pad) |
| Estado RoHS | Compliant |
Interfaces y conectores de SIM7600CE-A
No hay disponible una lista de interfaces publicada por el fabricante para SIM7600CE-A. Consulte la documentación del fabricante para obtener detalles sobre conectores y cabeceras.
Consulte la documentación del fabricante para ver el patillaje completo del conector de expansión y la numeración de pines del conector.
Aplicaciones típicas
SIM7600CE-A es adecuado para 6 aplicacións: Industrial IoT Gateways, Vehicle Tracking and Telematics, Smart Metering Backhaul, Security Cameras and Surveillance, POS and Payment Terminals, Remote Monitoring and Smart Agriculture.
Industrial IoT Gateways
The SIM7600CE-A's LTE Cat-4 throughput of 150 Mbps downlink and 50 Mbps uplink provides ample bandwidth for industrial gateways aggregating Modbus, CAN, or RS-485 field data into cloud platforms, while TD-SCDMA and GSM fallback maintains connectivity in areas without LTE coverage. Placed on the gateway main board as an LCC-mounted modem with USB interface to the host processor, the module supports always-on VPN tunnels and OTA firmware distribution. Its integrated GNSS allows location stamping of mobile or field-deployed gateways without a separate positioning chip, reducing BOM cost by one component. The main design consideration is the 2 A+ burst current of the Cat-4 transmitter, which requires a low-impedance 3.3-4.2 V rail with bulk capacitance near the VBAT pads.
Recomendado
Vehicle Tracking and Telematics
For fleet trackers, the SIM7600CE-A combines GPS + GLONASS + BeiDou positioning with LTE Cat-4 data in a single 30 x 30 mm LCC package, eliminating a discrete GNSS receiver and saving board area and cost. Position reports, CAN-bus telematics data, and driver-facing camera thumbnails can all be uploaded over the 50 Mbps uplink, while 2G fallback keeps trackers reporting even in coverage gaps. The LCC soldered mounting withstands automotive vibration better than pigtail or socket-mounted modems. Engineers should route the GNSS antenna away from the LTE transmit path to protect positioning sensitivity, and size the power rail for registration bursts that can momentarily exceed 2 A during cold-start network search at vehicle ignition.
Recomendado
Smart Metering Backhaul
Smart electricity and gas meters transmit interval load data and alarms over cellular networks where wired backhaul is unavailable. The SIM7600CE-A's multi-mode fallback (LTE-TDD B38/B39/B40/B41 down to GSM/GPRS/EDGE) matches the long 10-15 year service life of meters, surviving network technology transitions in the deployment region. Daily meter readings consume kilobytes, so the 150 Mbps Cat-4 link operates far below capacity - engineers prioritizing cost may instead select the pin-compatible SIM7600CE-T (Cat-1), which shares the same LCC footprint and lets one PCB design serve both high- and low-bandwidth meter tiers. Low-power SMS and data transmission modes keep quiescent battery draw acceptable in non-mains installations.
Recomendado
Security Cameras and Surveillance
Wireless surveillance cameras and NVR uplinks benefit directly from the SIM7600CE-A's 150 Mbps downlink and 50 Mbps uplink, sufficient for multiple 1080p H.264/H.265 video streams where wired Ethernet cannot reach. The module's LTE-TDD B38/B39/B40/B41 band support targets China-region private and carrier networks commonly used in city surveillance projects. Connected via USB to the camera SoC with AT-command control, the module adds negligible integration effort. Because sustained video upload drives the transmitter at high duty cycle, thermal design matters: the LCC pad array should be connected to a ground plane with adequate thermal vias to dissipate RF power amplifier heat, and the supply rail must sustain continuous multi-ampere bursts without droop-induced resets.
Recomendado
POS and Payment Terminals
Mobile point-of-sale terminals require dependable cellular connectivity for payment authorization plus optional location logging. The SIM7600CE-A provides both with its integrated GNSS and LTE Cat-4 modem: transactions are small packets where Cat-4 headroom simply guarantees low latency under congestion, while GPS/GLONASS/BeiDou positioning supports delivery-confirmation and fraud-screening workflows. Its compact 30 x 30 x 2.9 mm LCC package fits handheld enclosure constraints where mini-PCIe cards would be too bulky. Designers should implement the SIM card interface with ESD protection and ensure the 3.3-4.2 V battery rail tolerates the transmit burst profile; payment terminals certified for regional networks should confirm carrier band approval for the CE-region band plan before deployment.
Recomendado
Remote Monitoring and Smart Agriculture
Agricultural sensor nodes - soil moisture, weather stations, irrigation valves - use the SIM7600CE-A where 2G shutdowns have stranded GPRS-only designs: the module's GSM fallback and LTE-TDD support bridge legacy and modern networks. Sensor telemetry is low-rate, so the 150 Mbps capability provides future headroom for camera-based crop monitoring on the same infrastructure. The module's low-power SMS and data modes suit solar-bowered stations. One PCB can later carry the pin-compatible SIM7600CE-T or Fibocom L610 Cat-1 modules to cut recurring power and unit cost once bandwidth needs are fixed. Key layout practice: keep the antenna feedline short (50-ohm microstrip) and include a U.FL connector option for external high-gain antennas in field installations.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para SIM7600CE-A — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SIM7600CE | SIM7600CE-T | SIM7600CE-CNSE | Quectel EC21 |
|---|---|---|---|---|---|
| Package | LCC 30x30x2.9 mm | LCC 30x30x2.9 mm - same | LCC 30x30x2.9 mm - same | LCC 30x30x2.9 mm - same | LCC (verify pad map) |
| Brand | SIMCom Wireless Solutions | SIMCom Wireless Solutions | SIMCom Wireless Solutions | SIMCom Wireless Solutions | Quectel |
| LTE Category | Cat-4 (150/50 Mbps) | Cat-4 | Cat-1 (per etei.com) | Cat-4 | Cat-1/Cat-4 by variant |
| 2G/3G Fallback | TD-SCDMA / GSM-GPRS-EDGE / EVDO | Yes | Yes | Yes | GSM fallback (variant-dependent) |
| TDD-LTE Bands | B38/B39/B40/B41 | B38/B39/B40/B41 | B38/B39/B40/B41 | B38/B39/B40/B41 | Regional variant dependent |
| RoHS | Compliant | Compliant | Compliant | Compliant | Compliant |
Diferenciadores clave
- Integrated GNSS in the same footprint (frente a SIM7600CE-CNSE)
- LTE Cat-4 bandwidth advantage (frente a SIM7600CE-T)
- 2G/3G multi-mode fallback (frente a Fibocom L610)
Notas de diseño
LTE Cat-4 transmitters draw high burst currents during network registration and continuous uplink. The SIM7600CE Hardware Design guide requires a low-impedance 3.3-4.2 V battery rail with substantial bulk capacitance placed close to the VBAT pads. Estimated: if the module draws 2 A burst on a rail with 100 mOhm series impedance, the supply droop is 0.2 V - enough to trigger brown-out resets if the rail margin is thin. Use wide power traces or a dedicated plane and verify with an oscilloscope during PDP context activation.
The SIM7600CE-A is an LCC (leadless) module and must be assembled on a correctly defined land pattern with the recommended stencil aperture design for the perimeter pads and center ground area. Connect the center pad array to the main ground plane through an array of thermal vias to dissipate RF power amplifier heat and provide RF grounding. Follow the SIM7600CE/C Hardware Design V1.01 document for the exact land pattern dimensions before releasing the PCB footprint to fabrication.
Keep the 50-ohm antenna feedline as short as possible and provide a U.FL connector for external antennas in shielded enclosures. Separate the GNSS antenna from the LTE transmit path - simultaneous transmission at 23 dBm while receiving GNSS can desensitize positioning. Add ESD protection on the SIM interface and USB lines, since these are user-accessible in many terminal designs. Route USB differential pairs with 90-ohm controlled impedance when connecting to a high-speed host.
Información de cumplimiento
RoHS compliance per JLCPCB part listing for SIM7600CE-A. Other certifications not stated in provided data.
