TJA1086GHN/0Z - FlexRay Active Star Coupler 2 Branch | NXP
N.º de pieza: TJA1086GHN/0Z ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $8.95 | $8,95 |
| 10 | $8.1 | $81,00 |
| 100 | $7.25 | $725,00 |
| 500 | $6.6 | $3.300,00 |
| 1.000 | $5.9 | $5.900,00 |
TJA1086GHN/0Z Descripción general
An active star coupler is a network topology element used in automotive and industrial in-vehicle networks. Unlike a passive star, which simply splits the bus signal, an active star receives a frame on one branch, regenerates it, and re-transmits it to all other branches. This regeneration decouples electrical faults on one branch from the rest of the network, improving fault containment, signal integrity, and overall network robustness. In the hierarchy of in-vehicle networking ICs, the TJA1086G sits above simple bus line transceivers (such as FlexRay node transceivers) and belongs to the class of network interface and communication ICs.
Key features include full-duplex point-to-point branch links, TRXD0/TRXD1 receiver interfaces that allow several TJA1085G and TJA1086G devices to be cascaded to increase the number of branches in the network, and branch-related fault handling so a short or low-ohmic fault on one branch does not take down the whole star. The 44-HVQFN package with an exposed thermal pad provides low inductance and good thermal dissipation for the 9 x 9 mm footprint.
Technically, the device implements the analog front end and control logic needed to drive and receive FlexRay differential signals on each branch at 10 Mbit/s, with wake-up and sleep handling compatible with the FlexRay electrical physical layer. The /0Z ordering suffix identifies the standard grade and tape-and-reel delivery of this silicon. Moisture sensitivity level is MSL 1 with a 260 C peak reflow rating, simplifying SMT assembly.
Typical applications include chassis and body-domain FlexRay stars in passenger cars, gateway nodes aggregating multiple FlexRay branches, and safety-critical backbone networks where deterministic 10 Mbit/s communication with dual-channel redundancy is required.
When designing with this part, route each FlexRay branch as a matched differential pair and observe the bus termination guidelines of the FlexRay electrical physical layer specification; verify supply and enable pin configurations against the latest NXP datasheet before layout sign-off.
This page synthesizes distributor pricing references, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone.
Alternativas directas para TJA1086GHN/0Z — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
TJA1086GHN/0Z
✅ Sustitución directa✓ En stock
$5.9 / unidad
Ver hoja de datos →TJA1085GHN
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TJA1086GHN/0Z Especificaciones
| Product Type | FlexRay active star coupler |
| Number of Branches | 2 |
| Network Standard | FlexRay electrical physical layer V3.0.1 / ISO 17458-4 |
| Velocidad de datos | 10 Mbit/s |
| Cascade Interfaces | TRXD0 / TRXD1 |
| Encapsulado | 44-HVQFN (9 x 9 mm) |
| Tipo de montaje | Surface Mount |
| Nivel de sensibilidad a la humedad (MSL) | 1 |
| Peak Reflow Temperature | 260 C |
| Time at Peak Reflow Temperature | 30 s |
| Terminal Finish (JESD-609) | e4 (Nickel Palladium Gold Silver) |
| Number of Receivers / Drivers | 1 / 1 |
| Protocols Supported | FlexRay |
Guía de configuración de pines de TJA1086GHN/0Z 44-hvqfn (9 x 9 mm)
Configuración de pines para TJA1086GHN/0Z (encapsulado 44-hvqfn (9 x 9 mm)). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para TJA1086GHN/0Z.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
TJA1086GHN/0Z es adecuado para 6 aplicacións: Automotive FlexRay Backbone Networks, Chassis and Body Domain Star Topologies, Gateway Nodes with Multiple FlexRay Branches, Safety-Critical X-by-Wire Communication, Industrial and Test FlexRay Networks, Commercial Vehicle and Off-Highway Networks.
Automotive FlexRay Backbone Networks
The TJA1086GHN/0Z serves as the two-branch active star element in a vehicle FlexRay backbone, where deterministic 10 Mbit/s communication and branch fault isolation are mandatory. Because it complies with the FlexRay electrical physical layer V3.0.1 / ISO 17458-4, regenerated frames preserve the timing and signal quality requirements of the protocol across each branch. In a backbone role, a short or heavily attenuated branch does not bring down the entire network, a decisive advantage over passive bus wiring. The 44-HVQFN 9 x 9 mm package integrates the analog front ends for two branches in a single footprint, reducing BOM count versus discrete driver/receiver implementations, while the TRXD0/TRXD1 interfaces allow stacking additional couplers where more than two branches are required.
Recomendado
Chassis and Body Domain Star Topologies
In chassis and body domains, ECUs are grouped on physical branches that terminate at a central star point. The TJA1086GHN/0Z regenerates FlexRay frames at 10 Mbit/s between these branch groups, keeping signal amplitude and symmetry within V3.0.1 limits even when branch wiring lengths differ substantially. Its active regeneration contains electrical faults to a single branch, so a damaged harness segment affects only the ECUs on that branch - a critical property for availability-focused body functions. Designers typically place the coupler near the central harness junction; the exposed-pad HVQFN provides the grounding and thermal path needed for continuous full-traffic operation, and MSL 1 simplifies high-volume reflow assembly at automotive Tier-1 production lines.
Recomendado
Gateway Nodes with Multiple FlexRay Branches
Central gateways that bridge FlexRay to CAN, LIN, or Ethernet frequently terminate several FlexRay branches at one point. The TJA1086GHN/0Z provides two regenerated branches per device, and multiple devices connect through TRXD0/TRXD1 interfaces, per NXP, so a gateway can scale its star size with identical silicon. This uniformity eases qualification because all branch interfaces share one datasheet, one layout pattern, and one compliance story under ISO 17458-4. The 44-HVQFN 9 x 9 mm footprint keeps the gateway's FlexRay section compact; careful matched-pair routing from each branch pin to the connector preserves the 10 Mbit/s eye, and the e4 NiPdAu finish supports standard lead-free automotive assembly processes.
Recomendado
Safety-Critical X-by-Wire Communication
X-by-wire systems (steer-by-wire, brake-by-wire) rely on FlexRay's deterministic, dual-channel communication, and the active star coupler is the recommended topology element for fault containment in these safety-related networks. The TJA1086GHN/0Z isolates a faulty branch at 10 Mbit/s without propagating the fault, supporting the redundancy concepts required by safety-oriented in-vehicle networks. Its compliance with FlexRay electrical physical layer V3.0.1 / ISO 17458-4 ensures consistent bus timing across all branches, which deterministic protocols depend on. Designers should implement the wake-up and fault-handling behavior described in the NXP datasheet and validate the star's fail-operation behavior at network level, since branch isolation strategy is a system-safety decision.
Recomendado
Industrial and Test FlexRay Networks
Beyond road vehicles, FlexRay is used in industrial automation, robotics, and HIL test benches that emulate automotive networks. The TJA1086GHN/0Z lets test engineers create 10 Mbit/s star topologies that replicate the electrical behavior of a vehicle FlexRay plant, including branch fault injection, because its V3.0.1 / ISO 17458-4 compliance matches production ECUs. Its TRXD0/TRXD1 cascade capability allows bench setups with more than two branches using standard parts. The 44-HVQFN 9 x 9 mm package suits evaluation boards with controlled-impedance branch routing, and MSL 1 handling simplifies small-batch reflow work in lab environments. Verify termination resistor values against the FlexRay physical layer specification when building custom bench stars.
Recomendado
Commercial Vehicle and Off-Highway Networks
Trucks, buses, and off-highway machines adopt FlexRay where deterministic high-speed communication is needed for advanced driveline and stability functions. The TJA1086GHN/0Z provides the branch fault isolation that long, harshly routed harnesses demand: one damaged segment does not silence the whole star. With 10 Mbit/s regeneration compliant to FlexRay V3.0.1 / ISO 17458-4, frames maintain protocol timing across physically separated chassis zones. The rugged 44-HVQFN 9 x 9 mm package with exposed pad supports the vibration and thermal environment of commercial vehicles when properly soldered to an adequate ground pour, and the e4 NiPdAu terminal finish is compatible with lead-free automotive assembly standards used by commercial-vehicle Tier-1 suppliers.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TJA1086GHN/0Z — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | TJA1086GHN/0Z (Rochester Electronics) | TJA1085GHN |
|---|---|---|---|
| Package | 44-HVQFN (9 x 9 mm) | 44-HVQFN (9 x 9 mm) - same | 44-HVQFN - same family package |
| Brand | NXP Semiconductors | NXP Semiconductors (second source) | NXP Semiconductors |
| Network Standard | FlexRay V3.0.1 / ISO 17458-4 | FlexRay V3.0.1 / ISO 17458-4 | FlexRay V3.0.1 / ISO 17458-4 |
| TRXD Cascade Interface | TRXD0 / TRXD1 | TRXD0 / TRXD1 | TRXD0 / TRXD1 |
| Data Rate | 10 Mbit/s | 10 Mbit/s | 10 Mbit/s |
Diferenciadores clave
- Two-branch active star in a single package (frente a TJA1085GHN)
- FlexRay V3.0.1 / ISO 17458-4 compliance (frente a Generic node transceivers (e.g., TJA1080))
- Second-source availability of identical silicon (frente a TJA1086GHN/0Z via Rochester Electronics)
Notas de diseño
Route each FlexRay branch from the TJA1086GHN/0Z as a matched differential pair with controlled impedance per the FlexRay electrical physical layer V3.0.1 specification, and keep stub lengths to termination networks minimal. Solder the HVQFN exposed pad to a solid ground pour with an adequate via array - this pad is both the main ground return and thermal path for the 44-pin 9 x 9 mm package. Place decoupling capacitors within a few millimeters of the supply pins. Verify all 44 pin assignments against the NXP datasheet before layout release.
Because the TJA1086G regenerates frames at 10 Mbit/s, input and output branch networks should follow the termination values in the FlexRay electrical physical layer specification to keep eye diagrams within V3.0.1 masks. When cascading multiple couplers via TRXD0/TRXD1, keep these interface traces short and reference them to a continuous ground plane to avoid added skew that could erode protocol timing margin across the expanded star.
Do not treat the TJA1085GHN as a guaranteed drop-in without datasheet verification: while it belongs to the same FlexRay star-coupler family and shares the HVQFN housing, branch configuration and pinout details must be confirmed against the NXP datasheet. Also note that pricing for this specialized part varies widely (aggregator references from $0.55 to $64.20 per unit as of 2026-09-13), so secure allocation or a second source (Rochester Electronics) early in the program.
Información de cumplimiento
e4 terminal finish (Nickel Palladium Gold Silver) per JESD-609 indicates lead-free plating, consistent with RoHS-style assembly; full RoHS/REACH declarations must be confirmed from NXP's official product page or certificate of conformance. AEC-Q100 qualification not stated in provided data.
