XMC4500F100F768ACXQMA - 120MHz Cortex-M4 MCU | Infineon
N.º de pieza: XMC4500F100F768ACXQMA ✓ ActivoXMC4500F100F768ACXQMA Descripción general
An industrial microcontroller is a semiconductor integrated circuit that combines a processor core, embedded nonvolatile memory, communication peripherals, timers, and I/O interfaces on one device. The XMC4500 belongs to the XMC4000 family and uses the ARM Cortex-M4 architecture, placing it in the hierarchy of 32-bit MCU, microcontroller, embedded processor, and semiconductor. Its configurable peripheral set allows an industrial control design to combine real-time processing with Ethernet-connected equipment.
The verified device data identifies three principal performance points: a 120 MHz Cortex-M4 core, 768 kByte of Flash, and integrated Ethernet MAC support. The Cortex-M4 platform supports efficient control-oriented software, while the larger Flash capacity accommodates networking stacks, control algorithms, diagnostics, and application firmware. The Ethernet MAC makes the MCU suitable for connected industrial systems without requiring a separate network controller solely for Ethernet interface management.
Infineon describes the XMC4500 as combining a leading-edge peripheral set with the industry-standard ARM Cortex-M4 core. This combination targets energy-efficient industrial equipment where deterministic embedded control, communications, and configurable peripherals must coexist in one package. Distributor records further identify the target as the industrial XMC4000 MCU in a PG-LQFP-100-11 configuration.
Typical uses include industrial Ethernet controllers, connected factory equipment, industrial automation modules, embedded network bridges, and real-time supervisory controllers. In these systems, the 120 MHz processor can service communications and control tasks, while the 768 kByte Flash provides room for protocol stacks and firmware. The Ethernet MAC is especially relevant to machinery monitoring, networked sensors, and supervisory control equipment.
Designers should verify the complete pin assignment, exposed-pad connection, decoupling requirements, clock configuration, and startup sequence against the Infineon XMC4500 datasheet before layout release. The verified snippets do not enumerate all 100 pin names, so this page does not infer individual pin functions. Board design should preserve the manufacturer's recommended land pattern and exposed-pad implementation rather than treating the package as a generic LQFP.
This page combines verified manufacturer and distributor facts, same-family drop-in candidates, price information available on 2026-10-30, and practical qualification guidance. It also distinguishes confirmed specifications from data that must be obtained from the full manufacturer datasheet, helping engineers evaluate the XMC4500F100F768ACXQMA without relying on incomplete catalog descriptions.
Alternativas directas para XMC4500F100F768ACXQMA — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con XMC4500F100F768ACXQMA (mismo factor de forma y huella) — difiere en Product Type, Package, Architecture, Device Family.
XMC4500-F100F768AB
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
XMC4500-F100K768AB
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
XMC4500-F100K768AC
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
XMC4502-F100F768AB
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →XMC4504-F100K512AB
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →XMC4500F100F768ACXQMA Valores máximos y características eléctricas
| Product Type | 32-bit industrial microcontroller |
| Processor Core | ARM Cortex-M4 |
| Maximum CPU Frequency | 120 MHz |
| Embedded Flash Memory | 768 kByte |
| Programmable Peripheral Set | Configurable peripheral set |
| Ethernet Support | Ethernet MAC |
| Tensión de alimentación | 3.3 V |
| Device Family | XMC4000 |
| Series | XMC4500 |
| Encapsulado | PG-LQFP-100-11 |
| Recuento de pines | 100 pins |
| Architecture | 32-bit RISC |
| Tipo de montaje | Surface mount |
| Flash Organization | 768K x 8 bits |
Guía de configuración de pines de XMC4500F100F768ACXQMA pg-lqfp-100-11
Configuración de pines para XMC4500F100F768ACXQMA (encapsulado pg-lqfp-100-11). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para XMC4500F100F768ACXQMA.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
XMC4500F100F768ACXQMA es adecuado para 6 aplicacións: Industrial Ethernet Controllers, Factory Automation Equipment, Connected Sensors and Condition Monitoring, Industrial Motor and Motion Control, Industrial Communication Gateways, Embedded Network Bridges and Routers.
Industrial Ethernet Controllers
The XMC4500F100F768ACXQMA fits industrial Ethernet controller designs that require a 120 MHz Cortex-M4 core, 768 kByte of Flash, and an integrated Ethernet MAC. The MCU can execute protocol handling and real-time control tasks while leaving storage for drivers, diagnostics, and application logic. A typical implementation uses the MAC alongside an external Ethernet PHY, magnetics, and RJ45 interface. The benefit is integration of the network controller and 32-bit control processing in one 100-pin LQFP device, although the final design must validate PHY timing, clock configuration, and network-isolation requirements.
Recomendado
Factory Automation Equipment
The XMC4500F100F768ACXQMA is suitable for factory automation controllers because it combines a 120 MHz 32-bit Cortex-M4 core with 768 kByte of embedded Flash and configurable industrial peripherals. It can manage machine-state logic, communications, diagnostics, and supervisory tasks in one controller rather than splitting basic control across multiple devices. The 768 kByte Flash capacity also supports embedded networking and control software. Engineers should map the required pins, timers, communication channels, and exposed-pad implementation against the complete Infineon datasheet before committing the 100-pin LQFP layout.
Recomendado
Connected Sensors and Condition Monitoring
The XMC4500F100F768ACXQMA can serve as the control and communications processor in a connected condition-monitoring module. Its 120 MHz Cortex-M4 performance supports concurrent sensing, filtering, and network-service workloads, while 768 kByte of Flash provides room for protocol stacks and field-upgrade logic. The integrated Ethernet MAC enables network communication without a separate host processor, and configurable peripherals can support application-specific timing and I/O. Design validation should confirm ADC availability, sensor-interface channels, low-power requirements, and watchdog behavior because those details are not present in the supplied snippets.
Recomendado
Industrial Motor and Motion Control
The XMC4500F100F768ACXQMA is applicable to industrial motion-control subsystems where a deterministic 32-bit control processor and configurable peripheral set are needed alongside network management. Its 120 MHz Cortex-M4 core can execute control algorithms, while the Ethernet MAC supports supervisory connectivity and diagnostics. The 768 kByte Flash provides storage for motion code, parameter tables, and communication firmware. Before selecting the MCU, engineers must verify timer channels, capture functions, analog interfaces, pin multiplexing, and exposed-pad requirements in the manufacturer pin table because the verified excerpts do not enumerate them.
Recomendado
Industrial Communication Gateways
The XMC4500F100F768ACXQMA is well suited to communication gateways that translate between industrial links and Ethernet networks. The 120 MHz Cortex-M4 core provides processing capacity for protocol conversion, data buffering, and diagnostics, while 768 kByte of Flash supports multiple protocol stacks and configuration logic. Its integrated Ethernet MAC reduces the processing burden associated with network framing. The trade-off is that a gateway still needs appropriate external transceivers, connectors, timing devices, and isolation components. Firmware and pin-assignment reviews are essential because communications channels and electrical limits vary among XMC4500 derivatives.
Recomendado
Embedded Network Bridges and Routers
The XMC4500F100F768ACXQMA can support an embedded network bridge or industrial router requiring both Ethernet connectivity and substantial embedded firmware. The integrated Ethernet MAC handles the network interface, while the Cortex-M4 core at 120 MHz can support frame processing, protocol logic, and supervisory functions. The 768 kByte Flash capacity exceeds the 512 kByte designation of one same-brand alternative, making it preferable when code size is a constraint. Actual throughput depends on the selected PHY, Ethernet media, firmware architecture, and buffering strategy, none of which are quantified in the supplied search data.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para XMC4500F100F768ACXQMA — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | XMC4500-F100F768AB | XMC4500-F100K768AB | XMC4500-F100K768AC | XMC4502-F100F768AB | XMC4504-F100K512AB |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-LQFP-100-11 | PG-LQFP-100-11 - same | PG-LQFP-100-11 - same | PG-LQFP-100-11 - same | PG-LQFP-100-11 - same | PG-LQFP-100-11 - same |
| Embedded Flash Memory | 768 kByte | 768 kByte | 768 kByte | 768 kByte | 768 kByte | 512 kByte |
| Pin Count | 100 pins | 100 pins | 100 pins | 100 pins | 100 pins | 100 pins |
| Order Code Temperature Classification | F-grade ordering code | F-grade ordering code | K-grade ordering code | K-grade ordering code | F-grade ordering code | K-grade ordering code |
Diferenciadores clave
- Higher code capacity than the 512 kByte same-brand alternative (frente a XMC4504-F100K512AB)
- Exact verified price reference for the target ordering code (frente a XMC4500-F100F768AB)
- Exact target identification in distributor inventory (frente a XMC4500-F100K768AC)
- Same 100-pin family footprint supports focused substitution work (frente a XMC4502-F100F768AB)
Notas de diseño
Use the Infineon PG-LQFP-100-11 package drawing and land-pattern recommendation rather than a generic 100-pin LQFP footprint. Confirm exposed-pad dimensions, copper treatment, solder-mask clearance, and paste stencil geometry. The verified snippets do not include the complete pin table or exposed-pad recommendation, so board release should be gated on review of the official XMC4500 datasheet.
Place all required input, output, and decoupling capacitors directly at the corresponding power and ground pins, following the values and placement guidance in the manufacturer datasheet. Preserve uninterrupted ground-plane return paths beneath the device and keep high-current Ethernet or external-interface paths away from sensitive clock and analog inputs. The listed 3.3 V indication does not replace verification of the complete operating-voltage and absolute-maximum limits.
Do not treat all XMC4000 devices with similar flash capacities and 100-pin packages as automatically interchangeable. The ordering code can affect temperature classification and the derivative can have a different peripheral mix. Compare the complete pin list, clocks, communication channels, interrupt routing, package drawing, and ordering table before replacing the target or reusing an existing footprint without engineering approval.
Route Ethernet differential pairs according to the selected PHY and connector requirements, including controlled impedance, continuous reference plane, minimized stubs, and appropriate isolation from switching nodes. Separate external PHY, magnetics, and protection components from sensitive MCU supplies where practical. Although the MCU includes an Ethernet MAC, its clocking, I/O voltage, and PHY interface requirements must be established from the full datasheet before PCB layout.
Estimated from the verified identifiers, the 768 kByte Flash designation provides 786,432 bytes of code-storage capacity before considering boot or configuration overhead. Firmware planning should reserve space for bootloader updates, fault logs, calibration data, and network stacks; because Flash endurance and write timing were not supplied, treat this as capacity arithmetic rather than a lifetime specification and consult the manufacturer data for implementation limits.
Información de cumplimiento
The supplied verified search results do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for this exact ordering code. These values remain unknown rather than being inferred from the product family.
