DSP
محصولات (1,000+)
DSPIC33EP64MC204T-I/ML - 70 MIPS 16-Bit DSC 64KB Flash | Microchip
The Microchip DSPIC33EP64MC204T-I/ML is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering 70 MIPS performance with 64 KB (22K x 24) of Flash program memory and 8 KB of SRAM in a 44-pin QFN (8x8 mm, 0.65 mm pitch) surface-mount package. It operates from a 3.0 V to 3.6 V supply and integrates high-speed PWM, advanced analog peripherals, and DSP engine instructions. A digital signal controller combines the computational throughput of a digital signal processor with the control peripherals and deterministic interrupt architecture of a microcontroller. In the system hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP, making the dsPIC33EP family a popular choice for embedded control loops that require math-intensive processing such as field-oriented motor control and digital power conversion. Key features include the 70 MIPS dsPIC33E core, up to 27 general-purpose timers per the family datasheet (five hardware timers on this device), four DMA channels, and the high-speed PWM module that enables precise motor-control and power-supply waveforms without CPU-intensive bit banging. The 44-QFN (8x8) footprint conserves board area versus the 44-TQFP (10x10) alternative while keeping 0.65 mm lead pitch hand-solderable. Architecturally, the dsPIC33E core uses a modified Harvard pipeline with DSP multiply-accumulate instructions, two 40-bit accumulators, and a dedicated address generation unit. Flash-based program memory supports in-circuit self-programming, and the peripherals attach to multiple internal bus architectures for parallel data movement through DMA. Typical applications include brushless DC and PMSM motor control, digital power supplies and PFC stages, sensorless FOC drives, and industrial automation nodes where deterministic PWM timing is essential. Design consideration: the 3.0-3.6 V supply rail means 5 V sensor signals require level shifting, and the QFN exposed pad must be soldered to a grounded copper pour for both thermal relief and signal integrity. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC204T-I/MV - 16-bit 70 MIPS DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC204T-I/MV is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering 70 MIPS performance with 64KB (22K x 24) of Flash program memory and 8KB of RAM, housed in a 48-pin UQFN (6x6 mm) exposed-pad surface-mount package. A digital signal controller combines the computational capability of a digital signal processor (DSP) with the integrated peripherals and control architecture of a microcontroller. Within the power management hierarchy, DSCs such as the dsPIC33EP family sit at the intersection of general-purpose MCUs and dedicated DSPs, making them a common choice for closed-loop control systems where fast math and rich peripherals must coexist on a single chip. Key features of the DSPIC33EP64MC204T-I/MV include a 16-bit dsPIC33E core, motor control PWM (MCPWM) modules, and Quadrature Encoder Interface (QEI) inputs - the defining peripherals of the MC (Motor Control) variant. The device operates from a 3V to 3.6V supply across an industrial temperature range of -40C to +85C, and integrates multiple DMA channels and timer resources for efficient data movement and event sequencing without CPU overhead. Architecturally, the dsPIC33E core pairs the 16-bit MCU instruction set with DSP engine features such as multiply-accumulate operations, enabling real-time control algorithms like field-oriented control (FOC) for motors. The enhanced Flash program memory is organized in 24-bit instruction words, and the exposed-pad UQFN-48 package provides short die-to-PPCB thermal and electrical paths for high-frequency switching applications. Typical applications include brushless DC (BLDC) and permanent magnet synchronous motor (PMSM) drives, digital power supplies (AC/DC and DC/DC converters with digital loop compensation), power inverters, and industrial automation nodes requiring precise PWM generation and encoder feedback. A key design consideration: supply voltage must remain within the 3.0V to 3.6V window; decouple the VDD pins with low-ESR ceramics close to the package, and use the exposed thermal pad as a low-inductance ground connection. Clock configuration via PLL should be validated against the 70 MIPS ceiling in the datasheet. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with pricing verified as of 2026-09-25.
DSPIC33EP64MC204T-I/PT - 16-bit 70 MIPS DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC204T-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering up to 70 MIPS performance with 64 KB (22K x 24) of Flash program memory and 8 KB of SRAM, housed in a 44-pin TQFP (10x10 mm) package. A digital signal controller combines the computational capability of a digital signal processor with the peripheral integration and deterministic behavior of a microcontroller. Within the power management hierarchy of embedded systems, the DSC sits between a general-purpose MCU and a dedicated DSP: it executes single-cycle MAC and DSP instructions while providing motor-control-grade peripherals, making the dsPIC33E family a common choice for real-time closed-loop control. Key features of the DSPIC33EP64MC204T-I/PT include a 16-bit dsPIC CPU core with DSP-enhanced instruction set, 64 KB of self-programmable Flash, and 8 KB of on-chip RAM. It integrates high-speed MCPWM (motor control PWM), a Quadrature Encoder Interface (QEI) for position feedback, 3 on-chip operational amplifiers, 4 analog comparators, and 4 DMA channels. Connectivity covers I2C, SPI, UART/USART, IrDA, and LINbus. The device operates from a 3.0V to 3.6V single supply with an industrial temperature range of -40C to +85C (I suffix). Architecturally, the dsPIC33EP core uses a modified Harvard pipeline with a 24-bit instruction word and dual data read in a single cycle, enabling FIR/IIR filtering and field-oriented control (FOC) loops at rates impossible on standard 8-bit MCUs. The PTG (Pulse Train Generator) provides hardware sequencing without CPU intervention, offloading timing-critical tasks. Typical applications include brushless DC and PMSM motor control drives, digital power supplies (PFC, LLC), sensor signal conditioning using the integrated op-amps, and industrial automation nodes requiring QEI position feedback. Design consideration: decouple the 3.3V rail with at least one 0.1 uF ceramic capacitor per VDD pin placed within 2 mm of the pin, and connect all VSS pins to a solid ground plane to minimize PWM switching noise coupling into the analog peripherals. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing referenced as of 2026-09-25.
DSPIC33EP64MC206-E/PT - 16-bit 60 MIPS DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC206-E/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering up to 60 MIPS core performance with 64KB of Flash program memory and 8KB of RAM, housed in a 64-pin TQFP (PT) package with an extended industrial temperature rating of -40C to +125C. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy of embedded systems, the dsPIC33E family sits at the intersection of 16-bit MCUs and dedicated DSPs, offering the dsPIC DSC core with integrated DSP engine, making it a popular choice for embedded control engineers who need both math throughput and rich analog/peripheral integration in a single chip. Key features include the 16-bit dsPIC DSC core running up to 60 MIPS (70 MIPS family rating), 64KB self-programming Flash, 8KB SRAM, four direct memory access (DMA) channels, a barrel shifter, and boundary-scan (JTAG) support. The MC (motor control) peripheral set is the headline differentiator: dedicated motor control PWM (MCPWM), a quadrature encoder interface (QEI), three on-chip operational amplifiers and four comparators, plus a Peripheral Trigger Generator (PTG) for autonomous sequencing. Architecturally, the device uses a CMOS process with a modified Harvard bus structure and multiple internal bus architectures, enabling simultaneous instruction fetch and data access. The fixed-point DSP engine with barrel shifter accelerates control-loop math such as PID, Clarke/Park transforms, and digital filtering without external compute assistance. Typical applications include precision brushless DC and PMSM motor control, sensorless field-oriented control drives, digital power conversion, and industrial automation sensing nodes. The integrated op amps reduce external analog component count in current-sense front ends. When designing, note that multiple PGECx/PGEDx pin pairs exist; ICSP programming and debugging must use matched PGEC/PGED pairs, and all VDD/VSS pins must be connected for reliable operation. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with prices as of 2026-09-25.
DSPIC33EP64MC206-I/PT - 16-bit DSC 60MHz 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC206-I/PT is a 16-bit digital signal controller (DSC) with a 60 MHz dsPIC33E CPU core (up to 70 MIPS instruction throughput), 64KB of Flash program memory, and 8KB of SRAM, housed in a 64-lead TQFP (10x10 mm) surface-mount package. A digital signal controller combines the computational architecture of a microcontroller with the math acceleration of a DSP. In the embedded systems hierarchy, the dsPIC33EP family sits between general-purpose 16-bit MCUs and dedicated DSPs: it offers deterministic single-cycle MAC and DSP instructions for control loops, while retaining the peripherals, flash self-programming, and development ecosystem of an MCU. The dsPIC33EP MC-series specifically targets digital power and motor control. Key features include four DMA channels for moving ADC results without CPU intervention, five 16-bit timers, four external interrupt sources, high-speed PWM modules with complementary outputs and dead-time control, and a barrel shifter for fast bit manipulation. The 16-bit fixed-point architecture with DSP multiply-accumulate instructions executes typical current-loop control code in a few microseconds. Technical highlights of the dsPIC33EP core include an enhanced pipelined architecture, multiple internal bus structure, boundary-scan (JTAG) support for board test, and in-circuit serial programming (ICSP) via any PGECx/PGEDx pin pair. Flash is rated for reprogramming over the product lifecycle, and an internal fast RC oscillator allows operation without an external crystal in cost-sensitive designs. Typical applications include brushless DC (BLDC) and PMSM motor drives, switching power supplies and power factor correction stages, digital solar inverters, and sensor signal conditioning requiring fast filtering. Microchip reference designs such as the Low Power High Voltage Motor Control Board are built around this exact device. When designing with this DSC, use a pair of PGECx/PGEDx pins together for ICSP, decouple every VDD pin, and budget SRAM carefully since 8KB fills quickly with large control-loop buffers. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC206T-I/PT - 70 MIPS 64KB DSC 64-TQFP | Microchip
The Microchip Technology DSPIC33EP64MC206T-I/PT is a 16-bit digital signal controller (DSC) with a 70 MIPS dsPIC33E core, 64 KB (22K x 24) Flash program memory and 8 KB SRAM, housed in a 64-pin TQFP (10x10 mm) surface-mount package. It operates from a 3 V to 3.6 V single supply and integrates high-speed PWM, QEI, op-amps, comparators and advanced analog peripherals for embedded control. A digital signal controller combines the computational power of a digital signal processor (DSP) with the peripheral set and deterministic interrupt architecture of a microcontroller (MCU). In the power-management hierarchy, the dsPIC33EP family sits above general-purpose 16-bit MCUs and is optimized for closed-loop, math-intensive real-time control such as field-oriented motor control, digital power conversion and sensor signal processing. Key features include the 70 MIPS dsPIC DSC core with DSP instruction set (single-cycle MAC, 40-bit accumulator), 64 KB self-programmable Flash with ECC-class endurance, and 53 general-purpose I/O lines on this 64-pin device. The motor-control peripheral set delivers complementary or independent PWM outputs with dead-time insertion, quadrature encoder interfaces, and integrated analog comprising op-amps and comparators that reduce external BOM count in power stages. Architecturally, the dsPIC33EP core supports C and inline assembly development in Microchip MPLAB X IDE with the XC16 compiler, and is code-compatible within the dsPIC33E family, simplifying migration to larger Flash variants. The device offers 27 general-purpose timers grouped into several 16-bit timer blocks, multiple UART/SPI/I2C serial channels, DMA, and a watchdog with its own dedicated RC oscillator for fail-safe operation. Typical applications include brushless DC and PMSM motor drives, digital LED lighting power supplies, UPS and solar inverter control, and automotive/industrial sensor conditioning. The high-speed PWM resolution supports frequency and duty-cycle granularity required by peak-current-mode converters. Design consideration: the supply must be held within 3.0 V to 3.6 V, so regulate from 5 V rails with an LDO and place 0.1 uF decoupling at every VDD/VSS pair; the /MCLR pin requires a pull-up and RC for reliable programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC502-E/SO - 16-bit 60MIPS Motor Control DSC | Microchip
The Microchip DSPIC33EP64MC502-E/SO is a 16-bit digital signal controller (DSC) from the dsPIC33EP MC (Motor Control) family, delivering up to 60 MIPS (device-qualified variant; dsPIC33E core family tops at 70 MIPS) from 64 KB (22K x 24) of flash program memory and 8 KB of SRAM, housed in a 28-pin SOIC package with extended -40C to +125C temperature rating. A digital signal controller combines the computational throughput of a digital signal processor with the integrated peripherals and deterministic control architecture of a microcontroller. Within the power-management hierarchy, DSCs sit at the top of embedded control ICs, alongside general-purpose MCUs, and are purpose-built for closed-loop control systems such as digital power conversion and motor drive inverters. Key features include a 16-bit dsPIC33E core executing DSP-class multiply-accumulate instructions, an on-chip Motor Control PWM (MCPWM) module, a Quadrature Encoder Interface (QEI) for position feedback, and supply-voltage operation of 3 V to 3.6 V. The extended-temperature E grade supports operation to +125C, which is significant for enclosed motor-drive and automotive-adjacent environments. The dsPIC33EP architecture pairs a fast interrupt and context-switching model with DSP engine and hardware addressing modes, enabling tight FOC (Field-Oriented Control) loop times for brushless DC and permanent-magnet synchronous motor control. The AEC-Q100-qualified variant family confirms process robustness, while the tube packaging suits prototype and low-volume assembly. Typical applications include brushless DC motor drives, PMSM servo control, digital uninterruptible power supplies, and industrial automation nodes requiring synchronized PWM and encoder feedback. Design consideration: operate within the 3 V to 3.6 V supply window and budget flash usage carefully, since 64 KB is the family maximum for this 28-pin variant - no in-package upgrade path exists. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC502-I/MM - 16-bit 70 MIPS DSC, 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC502-I/MM is a 16-bit digital signal controller (DSC) delivering up to 70 MIPS DSP-enhanced performance at a 60 MHz maximum clock frequency, with 64 KB (22K x 24) of Flash program memory and 8 KB of SRAM, housed in a 28-pin QFN-S (6x6 mm) surface-mount package. A digital signal controller combines the control peripherals of a microcontroller with the mathematical throughput of a DSP engine on a single chip. Within the power-management hierarchy, the DSC sits above a standard MCU and below a full DSP-plus-MCU two-chip solution, making the dsPIC33E family a single-chip choice for embedded control loops that require multiply-accumulate throughput. Key features include the dsPIC33E core with integrated DSP instruction set, high-speed MCPWM (motor control PWM) peripherals, a Quadrature Encoder Interface (QEI) for positional feedback, 4 DMA channels, 5 timers, and 3 external interrupt sources. According to Microchip product data, the device uses a multiple internal bus architecture and CMOS process technology with low-power operating modes. The MC502 variant targets precision motor control: the high-speed PWM module with advanced analog integration enables field-oriented control of brushless DC (BLDC) and permanent magnet synchronous motors (PMSM) with fine PWM resolution. The 8K-word SRAM supports control-loop state variables, filters, and commutation tables without external memory. Typical applications include BLDC and PMSM motor drives, digital power supplies (DC-DC, PFC, inverters), battery charging systems, and industrial automation sensor nodes. The industrial temperature grade (-40C to +85C) suits factory-floor environments. Design consideration: the -I/MM package uses an exposed thermal pad that must be soldered to a grounded PCB pour for both thermal relief and signal integrity; also budget VDDCORE decoupling via the VCAP pin per the family datasheet DS70000657J. This page synthesizes distributor pricing, drop-in same-family alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet alone.
DSPIC33EP64MC502-I/SP - 16-bit 70 MIPS Motor Control DSC | Microchip
The Microchip Technology DSPIC33EP64MC502-I/SP is a 16-bit digital signal controller (DSC) from the dsPIC33EP64MC502 family, pairing a dsPIC DSC core rated up to 70 MIPS with 64 KB (22K x 24) of Flash program memory and 8 KB of SRAM, packaged in a 28-pin SPDIP (SP) through-hole package rated for industrial -40C to +85C operation. A digital signal controller is a hybrid device that merges the deterministic control structure of a microcontroller with the mathematical throughput of a digital signal processor. Within the power management and embedded hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP, making it the natural choice for closed-loop systems that need both fast multiply-accumulate operations and rich control peripherals. Key features of the DSPIC33EP64MC502-I/SP include a 16-bit pipeline core executing at 60 MHz (70 MIPS), a dedicated Motor Control PWM (MCPWM) module for complementary and center-aligned PWM generation, a Quadrature Encoder Interface (QEI) for position feedback, and CMOS technology with a 3.0 V to 3.6 V supply range per distributor datasheet summaries. Technically, the dsPIC33EP family integrates DSP instructions, a high-speed PWM with dead-time control, and enhanced analog peripherals. The 28-pin PDIP package makes this variant especially popular for prototyping, educational platforms, and through-hole production assemblies where rework must be simple. Typical applications include brushless DC motor control, permanent magnet synchronous motor drives, digital power supplies, and sensorless FOC systems. The integrated MCPWM and QEI peripherals directly serve precision motion products. Design consideration: the supply must be held within the 3.0 V to 3.6 V window, and the through-hole package adds lead inductance compared to surface-mount siblings, so decoupling capacitors should be placed very close to VDD pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC502T-E/SO - 16-bit 60 MIPS DSC, 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC502T-E/SO is a 16-bit dsPIC33EP digital signal controller (DSC) delivering up to 60 MIPS performance with 64KB (22K x 24) of Flash program memory and 8KB of SRAM, housed in a 28-pin SOIC package and qualified to AEC-Q100 for automotive environments. A digital signal controller combines the computational architecture of a microcontroller with the DSP engine of a digital signal processor. In the power-management hierarchy, the DSC sits between general-purpose MCUs and dedicated DSPs: it executes deterministic real-time control loops (such as field-oriented motor control) while retaining integrated peripherals, flash self-programming, and single-supply operation. Microchip's dsPIC33E family extends this category with high-speed PWM modules, quadrature encoder interfaces, and advanced analog integration. Key features of this part include the 16-bit dsPIC33EP core running at 60 MIPS with DSP multiply-accumulate instructions, a motor-control PWM peripheral with complementary outputs and dead-time insertion, and connectivity including CAN 2.0B, I2C, SPI, UART/USART, IrDA, LINbus, and QEI. The -E temperature suffix guarantees operation from -40C to +125C ambient, and the T suffix denotes tape-and-reel delivery for automated assembly. Technically, the dsPIC33EP core integrates a 17-bit x 17-bit hardware multiplier, 40-bit accumulators, and single-cycle MAC for filtering and transform operations, enabling sensorless brushless DC and permanent-magnet motor control with phase-current feedback. The peripheral ecosystem (input capture, output compare, 12-bit ADC with multiple sample-and-hold channels) supports current-loop bandwidths far beyond typical MCU implementations. Typical applications include brushless DC motor drives for appliances and HVAC blowers, permanent-magnet synchronous motor servo drives, digital power supplies and inverters, and CAN-networked automotive auxiliary actuators. Design consideration: supply voltage must be held within 3.0V to 3.6V; ensure 0.1uF decoupling at every VDD pin and verify FLASH erase/write endurance against your application's parameter-storage schedule. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC503-E/M5 - 60 MIPS DSC 64KB Flash 36-UQFN | Microchip
The Microchip Technology DSPIC33EP64MC503-E/M5 is a 16-bit digital signal controller (DSC) with a 60 MIPS dsPIC33E core, 64KB (22K x 24) of flash program memory, 8KB of RAM, and CAN 2.0B connectivity, housed in a 36-pin UQFN (VTLA, 5x5 mm) package with exposed pad. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and deterministic interrupt architecture of a microcontroller. DSCs sit within the broader embedded control hierarchy: microcontroller -> digital signal controller -> digital signal processor, and they are the device class of choice when a single chip must run control-loop mathematics (PID, field-oriented control) while also handling communications and housekeeping tasks. Key features of this MC503 variant include motor-control peripherals (MCPWM, quadrature encoder interface), three on-chip operational amplifiers and four comparators that reduce external analog component count, and a CAN module for industrial and automotive networking. The dsPIC33E core delivers 60 MIPS sustained performance from flash with a zero-overhead DSP multiply-accumulate and barrel shifter for efficient filtering. Architecturally, the device uses a modified Harvard 16-bit core with 24-bit instruction words, hardware loops, and two address generation units, allowing single-cycle MAC operations on DSP-style algorithms. The extended-temperature (-40C to +125C) 'E' grade suits harsh industrial environments. Typical applications include brushless DC and PMSM motor control drives, digital power supplies, and CAN-networked industrial sensing nodes. The motor-control PWM and QEI peripherals make it a natural fit for servo and traction drives. Design consideration: the 36-pin UQFN footprint places multiple VDD/VSS pairs close together; connect all power pins and decouple each pair with 0.1uF ceramics, and connect every PGECx/PGEDx pair correctly for ICSP programming. This page synthesizes verified distributor data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC504-E/MV - 16-bit 60 MIPS DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC504-E/MV is a 16-bit digital signal controller (DSC) from the dsPIC33EP64MC504 motor-control family, delivering up to 60 MIPS performance with 64KB (22K x 24) of Flash program memory, 8KB of SRAM, and 4KB of EEPROM, housed in a 48-pin UQFN (6x6 mm) package with exposed pad, rated from -40C to +125C. A digital signal controller combines the compute power of a DSP with the peripheral integration and ease of use of a microcontroller, sitting in the hierarchy between a general-purpose MCU and a dedicated DSP. The dsPIC33E family implements the dsPIC DSC core with DSP multiply-accumulate instructions, making it a natural fit for closed-loop power conversion and motion systems. Key features include an integrated motor-control PWM (MCPWM) module, quadrature encoder interface (QEI), CAN bus, three on-chip operational amplifiers, and four analog comparators. These analog front-end peripherals reduce external component count in motor-drive designs and simplify current-sense signal chains. Architecturally, the CMOS 16-bit core provides a fixed-point DSP engine, five 16-bit timers, and four DMA channels for efficient peripheral-to-memory data transfer. The on-chip op amps can be routed internally to comparator and ADC inputs, enabling field-oriented control (FOC) without external amplification stages. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, digital power supplies and inverters, and industrial automation nodes requiring CAN connectivity. When designing with this device, the 3.0V to 3.6V supply window must be respected and the UQFN exposed pad should be soldered to a grounded copper pour for thermal and signal integrity. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC504T-I/PT - 16-bit DSC 60MHz 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC504T-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP64MC504 motor-control family, delivering up to 60 MIPS (70 MIPS max core speed) performance with 64 KB of Flash program memory and 8 KB of RAM in a 44-pin TQFP (10x10 mm) surface-mount package. It operates from a 3.0 V to 3.6 V supply and integrates a Motor Control PWM (MCPWM) module, Quadrature Encoder Interface (QEI), CAN bus, three on-chip operational amplifiers, and four comparators. A digital signal controller combines the computational power of a digital signal processor with the control peripherals of a microcontroller. Within the power-management hierarchy, the dsPIC33E family sits in the 16-bit embedded controller class, bridging general-purpose MCUs and dedicated DSP ICs. DSCs execute multiply-accumulate (MAC) and DSP instructions in hardware, making them well suited to real-time closed-loop control algorithms such as field-oriented control (FOC) for motors. Key differentiating features include the high-speed MCPWM module for precise three-phase inverter drive, the QEI for direct encoder feedback, an on-chip CAN 2.0B controller for industrial networking, and integrated analog (3 op-amps, 4 comparators, advanced ADC) that reduces external component count in motor-drive signal chains. Up to 51 I/O lines are available on the 44-pin package. Architecturally, the dsPIC33E core is a modified Harvard, 16-bit pipelined processor with hardware DSP support, executing from zero-wait-state Flash at industrial temperature ranges (-40C to +85C for the -I option). CMOS process technology keeps active power low while supporting deterministic interrupt latency critical for control loops. Typical applications include brushless DC and permanent-magnet synchronous motor drives, power inverters, digital power supplies (PFC, LLC), and industrial automation nodes using CAN. The MCPWM plus QEI combination makes precision servo and BLDC control straightforward on this single chip. For design, note the 3.0 V to 3.6 V supply requirement: level shifting is needed for 5 V logic interfaces, and all VDD/VSS pairs must be decoupled with 0.1 uF ceramics placed close to the pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC504T-I/TL - 70 MIPS 16-bit DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC504T-I/TL is a 16-bit digital signal controller (DSC) from the dsPIC33EP64MC504 family, delivering 70 MIPS performance with a 64 KB (22K x 24) Flash program memory and 8 KB of data RAM, housed in a 44-pin VTLA (6x6 mm, 0.90 mm height) QFN surface-mount package. A digital signal controller combines the computational capability of a digital signal processor (DSP) with the peripheral integration and control architecture of a microcontroller (MCU). Within the power-management hierarchy, a DSC such as the dsPIC33EP family sits between general-purpose MCUs and dedicated DSPs, making it the preferred choice for closed-loop control systems that require fast multiply-accumulate operations alongside general I/O handling. Key features include the 70 MIPS dsPIC DSC core with integrated DSP engine, operating from a 3.0 V to 3.6 V single supply, 51 general-purpose I/O ports, and 27 general-purpose timers including nine 16-bit timers. The MCPWM (motor control PWM) module with Quadrature Encoder Interface (QEI) support is the headline peripheral for this MC (Motor Control) suffix variant. Architecturally, the dsPIC33EP core executes DSP instructions such as MAC and dual data fetch from 16-bit wide instruction words, supported by an 8 kB data RAM sized for control-loop buffering. Flash program memory is 64 KB (22K x 24), sufficient for field-oriented control (FOC) firmware with headroom for communication stacks. Typical applications include precision sensorless and sensored motor control (BLDC, PMSM, ACIM), digital power supplies and PFC stages, and industrial automation nodes where deterministic PWM timing matters. The -40C to +85C industrial temperature range supports factory-floor environments. Design consideration: the 3.0-3.6 V supply means 5 V logic interfaces require level shifting or 3.3 V-tolerant buffering; decouple VDD with 0.1 uF per pin plus bulk capacitance for clean ADC and PWM operation. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC506-E/PT - 16-bit DSC 64KB Flash 60MHz | Microchip
The Microchip Technology DSPIC33EP64MC506-E/PT is a 16-bit digital signal controller (DSC) with 64KB Flash program memory, 8KB SRAM, and a dsPIC33E core operating at up to 60 MHz, housed in a 64-pin TQFP (10x10 mm, PT) package with extended temperature operation from -40C to +125C. A digital signal controller combines the compute throughput of a digital signal processor with the peripheral integration and deterministic control flow of a microcontroller. Within the power management hierarchy of embedded systems, a DSC sits between a general-purpose MCU and a dedicated DSP, making the dsPIC33E family a leading choice for closed-loop motor control, digital power conversion, and sensor signal processing where a single chip must execute control loops, filtering mathematics, and communication tasks simultaneously. Key features include motor-control PWM (MCPWM) outputs with complementary modes and dead-time insertion, a quadrature encoder interface (QEI) for position feedback, a CAN 2.0B controller for industrial networking, three on-chip operational amplifiers, and four comparators. The 16-channel 10/12-bit ADC supports high-speed sampling of phase currents and bus voltages for field-oriented control (FOC) algorithms. The dsPIC33E core implements an enhanced Harvard architecture with DSP instructions (MAC, DSP multiply-accumulate), a 16x16 multiplier, and 40-bit accumulators, enabling single-cycle MAC operations critical for real-time current-loop bandwidth. The CMOS process delivers low active power with 3.0V to 3.6V supply operation. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, servo amplifiers, AC-DC and DC-DC digital power supplies, and industrial automation nodes using CAN bus. The 53 general-purpose I/O pins and 16-channel ADC make it well matched to multi-motor boards and sensor-dense systems. Design consideration: budget the VCAP core-regulator capacitor exactly per the manufacturer datasheet; omitting or misplacing it is the most common cause of startup instability on the dsPIC33E family. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EP64MC506-I/MR - 70 MIPS 16-bit DSC, 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC506-I/MR is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering 70 MIPS performance from a 64KB (22K x 24) flash memory with 8KB SRAM, housed in a 64-pin VQFN (MR, 9x9 mm, 0.90 mm height) surface-mount package operating from 3V to 3.6V. A digital signal controller combines the computational power of a digital signal processor (DSP) with the control peripherals and ease of use of a microcontroller (MCU). Within the power management hierarchy, the dsPIC33EP family sits in the 16-bit microcontroller and DSC class, targeting closed-loop real-time control systems such as motor drives, digital power supplies, and embedded control where deterministic interrupt latency and hardware PWM matter more than raw throughput. Key features of this part include the 70 MIPS dsPIC33E core with integrated DSP engine (single-cycle MAC, 40-bit accumulator), high-speed motor control PWM (MCPWM) with complementary outputs and dead-time insertion, a Quadrature Encoder Interface (QEI) for position feedback, one CAN 2.0B module for industrial networking, three on-chip operational amplifiers, and four analog comparators - reducing external component count in power-conversion designs. The architecture provides 27 general-purpose timers (per family documentation, nine 16-bit), a 16-channel 10/12-bit ADC option within the family, and up to 51 I/O ports on this 64-pin variant. Clock operation is specified at 60 MHz device frequency per distributor data, corresponding to the 70 MIPS instruction execution rate. The device operates over the industrial -40C to +85C temperature range indicated by the -I suffix, with supply voltage of 3V to 3.6V. Typical applications include precision motor control (BLDC, PMSM, AC induction), digital power supplies (PFC, LLC, solar inverters), industrial automation nodes with CAN connectivity, and sensor signal conditioning leveraging the on-chip op amps and comparators. The QEI module directly interfaces rotary encoders for servo drives. For design, ensure a clean 3.3V rail with local decoupling, and use Microchip MPLAB X IDE with XC16 compiler or MPLAB Code Configurator for firmware development; in-circuit debug uses ICSP via the PICkit or ICD tools. This page synthesizes distributor pricing, drop-in same-family alternatives, pinout/package guidance, and practical design notes not consolidated in the manufacturer datasheet.
DSPIC33EP64MC506-I/P - 70 MIPS 16-bit DSC | Microchip
The Microchip Technology DSPIC33EP64MC506-I/P is a 16-bit digital signal controller (DSC) from the dsPIC33EP64MC506 family, delivering up to 70 MIPS performance from its dsPIC DSC core with integrated DSP engine, 64 KB of flash program memory and 8 KB of SRAM, housed in a 64-pin TQFP package (10x10 mm) with industrial temperature rating (-40C to +85C). Per the family datasheet, the MC506 variant integrates high-speed motor-control PWM (MCPWM), a quadrature encoder interface (QEI), and advanced analog peripherals targeted at precision motor control. A digital signal controller combines the compute architecture of a microcontroller with the multiply-accumulate (MAC) DSP capability of a digital signal processor. In the power-management hierarchy, the dsPIC33E family sits within Microchip's 16-bit MCU/DSC portfolio, replacing separate MCU-plus-DSP two-chip solutions in embedded control systems such as motor drives, digital power supplies, and sensor fusion nodes. Key features include a 70 MIPS dsPIC DSC core with a single-cycle MAC and hardware divide, 16-bit fixed-point DSP instruction support, high-speed motor-control PWM outputs with complementary and center-aligned modes, quadrature encoder interface for servo feedback, multiple 16-bit timers, serial connectivity (UART, SPI, I2C), and a 3.0 V to 3.6 V single-supply operating range with 5 V-tolerant digital I/O. Architecturally, the core executes most instructions in a single cycle at up to 70 MIPS, with zero-overhead loops and hardware DO/REPEAT constructs that make control-loop code such as field-oriented control (FOC) deterministic. The on-chip DSP engine performs dual fetches and single-cycle MAC operations, critical for filter and transform computations in digitally controlled power conversion. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, solar inverters and digital power supplies, and industrial automation nodes. The MCPWM peripheral and QEI make this part a natural single-chip replacement for MCU-plus-encoder-counter designs in servo systems. Design consideration: the 3.0 V to 3.6 V supply requires a regulated 3.3 V rail; ensure adequate decoupling on all VDD/VSS pin pairs and follow Microchip's FOC reference designs for PWM dead-time settings. This page synthesizes verified distributor pricing, family drop-in variants, and design notes not found in a single manufacturer datasheet.
DSPIC33EP64MC506T-E/PT - 16-bit 60MIPS DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33EP64MC506T-E/PT is a 16-bit digital signal controller (DSC) with a dsPIC33E core running at 60 MIPS, 64KB (22K x 24) of Flash program memory, 8KB of SRAM, and a 64-pin TQFP (10x10 mm) package in an AEC-Q100 qualified, automotive-grade, extended-temperature (-40C to +125C) variant supplied in tape and reel. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and control architecture of a microcontroller. In the product hierarchy, the DSC sits between general-purpose MCUs and dedicated DSPs, making the dsPIC33E family a common choice for embedded control loops that require both fast math (MAC, DSP instructions) and rich on-chip peripherals such as high-speed PWM, quadrature encoder interfaces, and CAN. Key features include the 60 MIPS (70 MIPS max family core) 16-bit dsPIC DSC core, integrated DSP engine, dual 16-bit ADCs with selectable 10-bit or 12-bit resolution, motor-control PWM peripherals, CAN 2.0B, and 51 general-purpose I/O lines. The 3.0V to 3.6V supply range supports standard single-supply 3.3V designs. The device's architecture pairs the enhanced MCU core with hardware DSP support (single-cycle MAC, modulo and bit-reversed addressing), enabling FOC (field-oriented control), PID loops, and sensorless motor algorithms to execute within tight PWM-period deadlines. Multiple timers and output-compare channels support complex multi-phase PWM generation with dead-time insertion. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, industrial automation and robotics, power inverters and digital power supplies, and automotive auxiliary motor control where the AEC-Q100 qualification and -40C to +125C operating range of the E-grade part are required. Design consideration: budget the Flash carefully - 64KB (22K x 24 instruction words) is generous for FOC motor control but fills quickly with CAN stacks and bootloader code; plan for the ICD 3/REAL ICE programming interface early in the PCB layout. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, providing additional selection value beyond raw specification listings.
DSPIC33EP64MC506T-I/PT - 16-bit DSC 64KB Flash 60MIPS | Microchip
The Microchip Technology DSPIC33EP64MC506T-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP64MC506 family, delivering up to 60 MIPS (70 MIPS family maximum) with 64KB Flash program memory, 8KB SRAM, and 51 I/O pins in a 64-pin TQFP (10x10 mm) surface-mount package operating from 3V to 3.6V. A digital signal controller combines the compute throughput of a digital signal processor with the peripheral integration and deterministic control of a microcontroller. Within the power management hierarchy, the dsPIC33E family sits between general-purpose MCUs and dedicated DSPs, making it the standard choice for closed-loop motor control, digital power conversion, and embedded sensing where both fast math and rich peripherals are required in a single chip. Key features include a high-speed 16-bit DSP core with single-cycle MAC and 40-bit accumulator, motor-control PWM peripherals with complementary outputs and dead-time insertion, quadrature encoder interface (QEI) inputs for position feedback, a 10-bit/12-bit ADC, and multiple UART, SPI, and I2C serial ports. These peripherals are purpose-built for field-oriented control (FOC) of BLDC and PMSM motors. The dsPIC33EP architecture is based on an enhanced flash process with in-circuit serial programming (ICSP) via the MPLAB SNAP or PICkit programmers, allowing firmware updates on the production line without socketing the device. Clock speeds reach 60 MHz with a PLL from an external crystal or internal FRC oscillator. Typical applications include precision motor drives (BLDC, PMSM, ACIM), digital power supplies and solar inverters, industrial automation nodes, and power-factor-correction converters. Design consideration: keep the 3.0V to 3.6V supply rail within tolerance and place a 0.1uF decoupling capacitor at each VDD/VSS pin pair; motor-control PWM edges demand careful ground-plane discipline. This page synthesizes distributor pricing, drop-in alternatives across the dsPIC33EP family, and practical design notes not found in the manufacturer datasheet.
DSPIC33EV128GM003-E/M5 - 16-Bit 5V DSC 128KB Flash | Microchip
The Microchip Technology DSPIC33EV128GM003-E/M5 is a 16-bit 5V digital signal controller (DSC) with 128KB ECC Flash, 8KB RAM, a 60 MHz dsPIC33E CPU core, 6 motor-control PWM channels, 3 on-chip op amps, and CTMU (Charge Time Measurement Unit), housed in a 36-pin UQFN (5x5 mm) package with extended temperature range (-40C to +125C). A digital signal controller combines the compute throughput of a DSP (single-cycle MAC, DSP instruction set, dual operand fetch) with the peripheral integration and interrupt latency of a microcontroller. Within the power-management hierarchy, the dsPIC33EV family sits in the broader class of embedded MCUs and is specifically aimed at 5V industrial nodes where 3.3V controllers would require extra level-shifting and supply complexity. Key features include 60 MIPS execution (40 MIPS for the -H variant), Flash Error Correction Code (ECC) for functional safety designs, 3 integrated op amps that offload external signal-conditioning for current shunt sensing, 6 MC PWM channels with dead-time control, SENT peripheral support for automotive sensor interfaces, and the CTMU for capacitive touch and precise time measurement. Supply voltage spans 4.5V to 5.5V per distributor specification data. Architecturally, the device uses the 16-bit dsPIC33E core with a multiple internal bus architecture, hardware DSP multiply-accumulate, and a full set of serial peripherals (UART, SPI, I2C) for system connectivity. The 128KB (43K x 24) ECC-protected program memory supports Class B functional safety libraries; DigiKey lists the part under Microchip's Functional Safety (FuSa) category. Typical applications include automotive sensor and touch control units, BLDC and PMSM motor control in appliances, industrial power supplies and digital lighting, and harsh-environment sensing where 5V noise immunity matters. Design consideration: the UQFN-36 (5x5) footprint requires careful thermal pad soldering; plan the exposed pad land pattern per Microchip layout guidelines to ensure reliable grounding and heat dissipation. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EV128GM004-E/P8 - 16-Bit 60MHz 5V DSC 128KB Flash | Microchip
The Microchip Technology DSPIC33EV128GM004-E/P8 is a 16-bit digital signal controller (DSC) with a 5V dsPIC33EV core running at 60 MHz (up to 70 MIPS family performance), 128KB (43K x 24) of ECC Flash and 4KB of RAM, housed in a 48-pin TQFP (7x7 mm) package. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and control architecture of a microcontroller, sitting in the system hierarchy between a general-purpose MCU and a dedicated DSP. Within that category, the dsPIC33EV family is Microchip's 5V-tolerant, robust DSC line targeted at harsh electrical environments such as automotive, appliance and industrial control, where 3.3V processors require extra level-shifting circuitry. Key features include 128KB of self-programmable ECC Flash for functional-safety designs, 4KB of RAM, six motor-control PWM channels for inverter and BLDC control, three integrated operational amplifiers that reduce external analog component count, a Charge Time Measurement Unit (CTMU) for capacitive touch and time-domain measurements, and a SENT peripheral compliant with automotive sensor networking requirements. Architecturally, the dsPIC33EV core provides DSP-class multiply-accumulate instructions alongside deterministic interrupt latency, while the ECC Flash protects program memory against single-bit faults - a prerequisite for safety-oriented applications. The 5V operating range simplifies connection to automotive 5V sensors and industrial I/O without level translators. Typical applications include automotive sensor and touch-control units, BLDC and PMSM motor drives, switched-mode power supplies, and harsh-environment industrial automation nodes. A key design consideration is thermal budget: the -E suffix qualifies the device for -40C to +125C ambient operation, but package thermal resistance and copper pour sizing must still be verified for high-PWM-load motor-control use. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33EV128GM004-I/P8 - 16-Bit 5V DSC 128KB Flash 48-TQFP | Microchip
The Microchip Technology DSPIC33EV128GM004-I/P8 is a 16-bit 5V digital signal controller (DSC) from the dsPIC33EV family with 128KB (43K x 24) ECC Flash, 4KB RAM, a core clocked up to 60 MHz (70 MIPS performance class), six motor-control PWM channels, three on-chip operational amplifiers, a CTMU charge-time-measurement unit, and SENT peripheral support, housed in a 48-pin TQFP (7x7 mm) package. A digital signal controller combines the computational architecture of a digital signal processor with the peripheral set and control peripherals of a microcontroller. Within the power-management hierarchy of embedded systems, a DSC such as the dsPIC33EV sits at the top of the control chain: it reads sensors, executes control-loop algorithms such as field-oriented motor control, and drives power stages directly. The 5V operation of the dsPIC33EV family distinguishes it from most 3.3V MCUs, improving noise immunity in harsh environments. Key features include error-correcting-code (ECC) Flash for improved functional safety, a broad operating voltage suited to industrial and automotive 5V rails, an integrated CTMU for capacitive touch and time measurement, three analog op amps that reduce external component count in current-sense front ends, and a SENT interface for automotive sensor connectivity. Architecturally, the dsPIC33EV core is a 16-bit modified Harvard pipeline with DSP multiply-accumulate instructions, hardware division support, and single-cycle MAC operation, enabling real-time control loops such as field-oriented control (FOC) of PMSM and BLDC motors. Peripheral Pin Select (PPS) allows flexible remapping of digital peripherals onto RPn pins, simplifying PCB routing. Typical applications include electric power steering and automotive sensor modules, industrial motor drives and power conversion, and appliance control boards, where the 5V core, motor-control PWMs, and on-chip op amps reduce board size and improve EMI robustness. Design consideration: verify the Flash programming specification and use Microchip certified tools (MPLAB X, ICD, REAL ICE) for functional-safety workflows, and reserve the VCAP pin with the specified external capacitor for stable internal core regulation. This page synthesizes distributor listings, family datasheet references, drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.
DSPIC33EV128GM004-I/PT - 70MIPS 5V DSC 128KB | Microchip
The Microchip Technology DSPIC33EV128GM004-I/PT is a 16-bit digital signal controller (DSC) with a 70 MIPS dsPIC33EV core operating from a 5V supply, 128KB (43K x 24) ECC Flash program memory, 8KB RAM, and 44 pins in a 10x10 mm TQFP package. A digital signal controller combines the computational architecture of a digital signal processor with the peripheral integration and ease of use of a microcontroller. Within the embedded-systems hierarchy, the dsPIC33EV sits under the dsPIC33E family, which belongs to Microchip's 16-bit MCU/DSC portfolio, itself a subcategory of digital signal controllers used in industrial power conversion, motor control, and automotive sensing systems. DSCs typically add hardware multiply-accumulate (MAC) DSP instructions, high-resolution PWM, and fast ADCs to a standard MCU core. Key features of the DSPIC33EV128GM004-I/PT include its 5V-rated operation, which improves noise immunity in harsh electrical environments compared with 3.3V-only parts; single-cycle MAC and DSP engine support for control loops; ECC Flash for functional-safety oriented designs (DigiKey lists it as a dsPIC 33EV Functional Safety (FuSa) device); and Peripheral Pin Select (PPS), which allows remapping of many digital peripherals to any compatible RPn pin for flexible board routing. Technical depth: the device executes up to 70 million instructions per second at its maximum clock frequency and integrates peripherals such as motor-control PWM, SENT, op-amps, and analog comparators per the family datasheet (DS70005144H). The 128KB Flash is organized in 24-bit instruction words, and the core supports DSP multiply-accumulate and barrel-shifter operations. The industrial temperature grade (suffix I) covers -40C to +85C. Typical applications include brushless DC and PMSM motor control in appliances, automotive sensors and touch-control units, digital power supplies and AC-DC converters, and industrial HVAC controls where robust 5V noise immunity is required. Design consideration: budget decoupling on every VDD/VDDCORE pin and provide the correct VCAP capacitor for the internal core regulator; the 5V core-family devices are sensitive to supply transients in high-PWM-noise environments. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone. Pricing references are as of 2026-09-26.
DSPIC33EV128GM004T-E/MLVAO - 16-Bit 60 MIPS DSC, 128KB Flash | Microchip
The Microchip Technology DSPIC33EV128GM004T-E/MLVAO is a 16-bit digital signal controller (DSC) from the dsPIC33EV family, delivering up to 60 MIPS at 5V operation with 128KB (43K x 24) of ECC Flash program memory, housed in a 44-pin QFN (8x8 mm) package with exposed thermal pad. A digital signal controller combines the computational strengths of a microcontroller (MCU) with the DSP-centric features of a digital signal processor in a single core. Within the power-management hierarchy, the dsPIC33EV sits between general-purpose MCUs and dedicated DSPs, providing an optimized architecture for real-time control, digital power conversion, and motor control where both math throughput and robust peripherals are required. Key features include a 16-bit dsPIC DSC core running at up to 60 MIPS with 5V-tolerant operation, 128KB of self-programmable ECC Flash for functional-safety oriented designs, an extended temperature grade (E suffix) supporting operation up to +125C ambient, and automotive-focused qualification (AEC-Q100 per distributor listings) suited to harsh environments. Technically, the dsPIC33EV core integrates DSP instructions, a hardware multiplier, and a rich peripheral set including CAN and UART/serial connectivity modules, enabling single-chip closed-loop control of motors and digital power stages. The 5V native I/O removes the need for level shifting in many industrial and automotive 12V-derived systems, improving noise immunity versus 3.3V-only controllers. Typical applications include brushed and brushless DC motor control, digital power supplies and LED drivers, automotive body and convenience modules, and industrial appliances that must operate reliably in noisy, high-temperature environments. Design consideration: the E-grade part must still be derated at high ambient temperatures; ensure QFN exposed-pad thermal relief on the PCB (solid ground-plane copper pour with thermal vias) to keep junction temperature within limits at 60 MIPS operation. This page synthesizes distributor inventory data, drop-in same-package alternatives, and practical design guidance not found in the manufacturer datasheet alone.