محصولات (46,000+)

SP3232EEP-L - Dual RS-232 Transceiver | MaxLinear
SP3232EEP-L

SP3232EEP-L - Dual RS-232 Transceiver | MaxLinear

MaxLinear SP3232EEP-L is a full-duplex RS-232 transceiver integrating two drivers and two receivers in a 16-pin PDIP package. It operates from a single 3.3 V to 5.5 V supply and supports true RS-232 signal levels, making it suitable for portable equipment and systems that need bidirectional serial communication over longer distances than a logic-level interface can provide. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels defined by the RS-232 standard. The transmitter raises and inverts data signals for transmission, while the receiver converts incoming bipolar signals into CMOS-compatible logic. A dual-transceiver device provides two independent communication paths and is commonly used in console ports, data acquisition equipment, instrumentation, and embedded control systems. The SP3232E family uses an on-chip charge-pump supply and associated external capacitors to generate the positive and negative voltages required for true RS-232 operation. MaxLinear states that the SP3232E charge pump can operate with only 0.1 uF capacitors in 3.3 V systems. This capacitor requirement helps reduce board area while preserving the voltage levels needed by RS-232 receivers and drivers. The SP3232EEP-L combines the electrical functions of two RS-232 transmitters and two RS-232 receivers in one device. Its 16-pin PDIP format is suitable for conventional through-hole assembly, prototyping, repair work, and industrial or legacy control equipment. Because the package uses through-hole leads, it also provides generous mechanical spacing and is generally easier to inspect or rework than a fine-pitch surface-mount package. Typical applications include RS-232 console connections, laboratory and test equipment, industrial controller interfaces, configuration ports, and embedded systems that communicate with older peripherals. The two-driver, two-receiver organization allows simultaneous transmit and receive activity on each channel where the connected equipment supports full-duplex RS-232 communication. Design the charge-pump capacitor network with the values and layout specified in the manufacturer datasheet. Keep the transceiver close to the connector, provide a common ground path between the systems, route the differential charge-pump capacitor connections away from sensitive analog circuitry, and confirm that the selected connector and cable satisfy the intended RS-232 application. This product page combines the device architecture, package information, application guidance, sourcing workflow, and a structured list of datasheet and cross-reference resources. It also distinguishes confirmed drop-in substitutions from candidates that require pinout, package, and electrical verification before being used in a replacement design.

RFQ تماس
SP3232EET-L - 120 kbps RS-232 Transceiver | MaxLinear
SP3232EET-L

SP3232EET-L - 120 kbps RS-232 Transceiver | MaxLinear

The MaxLinear SP3232EET-L is a true +3.0 V to +5.5 V RS-232 transceiver in a 16-SOIC package, providing two transmit and two receive channels at up to 120 kbps. It is designed for portable and handheld equipment, including notebook computers, palmtop computers, and other portable serial interfaces. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts incoming RS-232 signals back into logic-level signals. The SP3232EET-L belongs to the interface IC hierarchy: RS-232 interface IC > line-driver and line-receiver transceiver > communications interface semiconductor. Its integrated charge-pump power supply supports true RS-232 operation from a single low-voltage supply while reducing the external capacitor count. The device operates from a +3.0 V to +5.5 V supply and supports data rates up to 120 kbps under full load. The manufacturer datasheet identifies the SP3222E/SP3232E family as suitable for portable or hand-held applications and states that the high-efficiency charge-pump supply requires only 0.1 uF capacitors in 3.3 V operation. Its 1 mA supply-current specification supports low-power interface designs, while the -40 C to +85 C operating-temperature range supports industrial and commercial equipment. The SP3232EET-L contains two RS-232 drivers and two RS-232 receivers in a 16-SOIC package. It is appropriate for systems that require bidirectional serial communication, including point-to-point links, service consoles, industrial controllers, data-acquisition equipment, and portable peripheral connections. The -L ordering suffix identifies the leaded package variant identified in the verified distributor records. A key design consideration is the charge-pump capacitor network. The datasheet states that the SP3232E series requires only 0.1 uF capacitors for 3.3 V operation. These capacitors should be placed close to the charge-pump pins, with short and symmetric routing helping reduce switching disturbance and ensuring stable operation. This product page consolidates the verified distributor specifications, manufacturer datasheet information, package details, pricing references, and available drop-in alternatives. It is intended to help engineers identify whether the SP3232EET-L fits a low-voltage, moderate-speed RS-232 interface before committing to a PCB layout.

RFQ تماس
SP3232EET-L/TR - 120 kbps RS-232 Transceiver | MaxLinear (Tape & Reel)
SP3232EET-L/TR

SP3232EET-L/TR - 120 kbps RS-232 Transceiver | MaxLinear (Tape & Reel)

The MaxLinear SP3232EET-L/TR is a true +3.0 V to +5.5 V RS-232 transceiver in a 16-SOIC package, providing two transmit and two receive channels at up to 120 kbps. It is designed for portable and handheld equipment, including notebook computers, palmtop computers, and other portable serial interfaces. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts incoming RS-232 signals back into logic-level signals. The SP3232EET-L/TR belongs to the interface IC hierarchy: RS-232 interface IC > line-driver and line-receiver transceiver > communications interface semiconductor. Its integrated charge-pump power supply supports true RS-232 operation from a single low-voltage supply while reducing the external capacitor count. The device operates from a +3.0 V to +5.5 V supply and supports data rates up to 120 kbps under full load. The manufacturer datasheet identifies the SP3222E/SP3232E family as suitable for portable or hand-held applications and states that the high-efficiency charge-pump supply requires only 0.1 uF capacitors in 3.3 V operation. Its 1 mA supply-current specification supports low-power interface designs, while the -40 C to +85 C operating-temperature range supports industrial and commercial equipment. The SP3232EET-L/TR contains two RS-232 drivers and two RS-232 receivers in a 16-SOIC package. It is appropriate for systems that require bidirectional serial communication, including point-to-point links, service consoles, industrial controllers, data-acquisition equipment, and portable peripheral connections. The -L ordering suffix identifies the leaded package variant identified in the verified distributor records. A key design consideration is the charge-pump capacitor network. The datasheet states that the SP3232E series requires only 0.1 uF capacitors for 3.3 V operation. These capacitors should be placed close to the charge-pump pins, with short and symmetric routing helping reduce switching disturbance and ensuring stable operation. This product page consolidates the verified distributor specifications, manufacturer datasheet information, package details, pricing references, and available drop-in alternatives. It is intended to help engineers identify whether the SP3232EET-L/TR fits a low-voltage, moderate-speed RS-232 interface before committing to a PCB layout.

RFQ تماس
SP3232EEY-L - 120kbps Dual RS-232 | MaxLinear | TSSOP-16
SP3232EEY-L

SP3232EEY-L - 120kbps Dual RS-232 | MaxLinear | TSSOP-16

The MaxLinear, Inc. SP3232EEY-L is a 120 kbps, dual RS-232 transceiver with two drivers and two receivers, operating from a single 3.0 V to 5.5 V supply in a 16-pin TSSOP package. It provides true RS-232 interface conversion between TTL/CMOS logic levels and EIA/TIA-232-F signals. A high-efficiency charge-pump supply supports low-voltage operation and requires only 0.1 µF capacitors at 3.3 V. An RS-232 transceiver is an interface IC that translates digital logic-level signals into voltage-limited, polarity-aware differential signals used by RS-232 links. Within the hierarchy of interface circuits, it connects UART-compatible logic to serial equipment through the RS-232 electrical standard. This makes the SP3232EEY-L useful where a modern embedded system must communicate with legacy, industrial, or service equipment through a wired serial port. The SP3232EEY-L supports data rates up to 120 kbps under full load and accepts a 3.0 V to 5.5 V operating supply range. Its 1 mA supply-current specification suits portable and embedded systems, while the 16-pin TSSOP package supports compact surface-mount PCB layouts. The two-driver, two-receiver arrangement can implement two RS-232 channels or provide driver and receiver resources for one channel. Its charge-pump architecture generates the positive and negative voltage levels needed by true RS-232 operation without a separate bipolar supply. At 3.3 V, the manufacturer documentation specifies operation with 0.1 µF charge-pump capacitors. The external capacitor selection and layout remain important because an unsuitable capacitor type or long trace can increase output distortion or reduce reliable data-rate margin. Typical applications include embedded UART expansion, portable diagnostic equipment, industrial serial interfaces, point-of-sale terminals, security equipment, and service-console adapters. The device is particularly appropriate for equipment that must use a full RS-232 interface while operating from a 3.3 V or 5 V logic supply rather than a conventional ±12 V RS-232 supply. When designing around the SP3232EEY-L, verify the exact pin assignments, charge-pump capacitor requirements, and transceiver enable or shutdown behavior against the manufacturer datasheet before PCB release. Place the required capacitors close to their associated pins, provide a solid ground connection, and route connector-facing driver outputs away from sensitive receiver and logic signals. This product page combines the verified manufacturer specifications, distributor availability information, same-family drop-in candidates, and practical interface-design guidance. It also distinguishes verified electrical attributes from parameters that still require datasheet confirmation, helping engineers evaluate fit before committing a compact RS-232 design to production.

RFQ تماس
SP3232EEY-L/TR - 120kbps Dual RS-232 | MaxLinear | TSSOP-16 (Tape & Reel)
SP3232EEY-L/TR

SP3232EEY-L/TR - 120kbps Dual RS-232 | MaxLinear | TSSOP-16 (Tape & Reel)

The MaxLinear, Inc. SP3232EEY-L/TR is a 120 kbps, dual RS-232 transceiver with two drivers and two receivers, operating from a single 3.0 V to 5.5 V supply in a 16-pin TSSOP package. It provides true RS-232 interface conversion between TTL/CMOS logic levels and EIA/TIA-232-F signals. A high-efficiency charge-pump supply supports low-voltage operation and requires only 0.1 µF capacitors at 3.3 V. An RS-232 transceiver is an interface IC that translates digital logic-level signals into voltage-limited, polarity-aware differential signals used by RS-232 links. Within the hierarchy of interface circuits, it connects UART-compatible logic to serial equipment through the RS-232 electrical standard. This makes the SP3232EEY-L/TR useful where a modern embedded system must communicate with legacy, industrial, or service equipment through a wired serial port. The SP3232EEY-L/TR supports data rates up to 120 kbps under full load and accepts a 3.0 V to 5.5 V operating supply range. Its 1 mA supply-current specification suits portable and embedded systems, while the 16-pin TSSOP package supports compact surface-mount PCB layouts. The two-driver, two-receiver arrangement can implement two RS-232 channels or provide driver and receiver resources for one channel. Its charge-pump architecture generates the positive and negative voltage levels needed by true RS-232 operation without a separate bipolar supply. At 3.3 V, the manufacturer documentation specifies operation with 0.1 µF charge-pump capacitors. The external capacitor selection and layout remain important because an unsuitable capacitor type or long trace can increase output distortion or reduce reliable data-rate margin. Typical applications include embedded UART expansion, portable diagnostic equipment, industrial serial interfaces, point-of-sale terminals, security equipment, and service-console adapters. The device is particularly appropriate for equipment that must use a full RS-232 interface while operating from a 3.3 V or 5 V logic supply rather than a conventional ±12 V RS-232 supply. When designing around the SP3232EEY-L/TR, verify the exact pin assignments, charge-pump capacitor requirements, and transceiver enable or shutdown behavior against the manufacturer datasheet before PCB release. Place the required capacitors close to their associated pins, provide a solid ground connection, and route connector-facing driver outputs away from sensitive receiver and logic signals. This product page combines the verified manufacturer specifications, distributor availability information, same-family drop-in candidates, and practical interface-design guidance. It also distinguishes verified electrical attributes from parameters that still require datasheet confirmation, helping engineers evaluate fit before committing a compact RS-232 design to production.

RFQ تماس
SP3232EHCA-L/TR - 3.3V 460kbps RS-232 Transceiver | MaxLinear
SP3232EHCA-L/TR

SP3232EHCA-L/TR - 3.3V 460kbps RS-232 Transceiver | MaxLinear

The MaxLinear SP3232EHCA-L/TR is a 3.3V RS-232 interface transceiver with two drivers, two receivers, a 460 kbps data rate, and a 16-pin SSOP package. It operates from a 3 V to 5.5 V supply and supports true EIA/TIA-232-F signaling from a supply as low as 2.7 V. Enhanced ESD protection reaches 15 kV under the Human Body Model. An RS-232 transceiver is an interface IC that converts logic-level signals between a digital system and the voltage-defined RS-232 port. The SP3232EH series belongs to the transceiver hierarchy within interface ICs, bridging embedded controllers, data-processing equipment, and legacy serial peripherals. Its two-driver, two-receiver arrangement supports full-duplex communication while keeping the external interface compact. The main engineering features include a 460 kbps maximum data rate, operation across 3 V to 5.5 V, true EIA/TIA-232-F compliance, interoperability with RS-232 equipment operating from a 2.7 V supply, and enhanced 15 kV HBM ESD protection. The charge-pump supply architecture requires only 0.1 µF capacitors in 3.3 V operation, reducing external component count compared with implementations that need larger energy-storage capacitors. Designed for portable and hand-held equipment, the SP3232EH combines four interface channels with low-voltage operation. Charge-pump circuitry generates the bipolar voltage levels required by RS-232 while the logic-side interface remains compatible with modern digital supply rails. Its 16-pin SSOP format supports compact layouts where a higher-pin-count package would be unnecessary. Typical uses include notebook and palmtop computer serial ports, handheld instrumentation, point-of-sale equipment, industrial data acquisition, and embedded systems that retain an RS-232 connection. The 460 kbps capability is suitable for moderate-speed serial links, while 15 kV HBM protection improves interface robustness in exposed equipment. When laying out the circuit, keep the charge-pump capacitors and RS-232 charge-pump nodes close to the device, preserve the datasheet-defined capacitor values, and route driver outputs and receiver inputs away from sensitive logic. Confirm that the selected cable and connector provide the intended ground reference and protection arrangement for the installation environment. This product record combines electrical specifications, same-footprint family alternatives, application guidance, and design-focused considerations to support faster component selection, PCB planning, and RS-232 interface qualification.

RFQ تماس
SP3232EHCT-L/TR - 3.3V 460kbps RS-232 Transceiver | MaxLinear
SP3232EHCT-L/TR

SP3232EHCT-L/TR - 3.3V 460kbps RS-232 Transceiver | MaxLinear

The MaxLinear SP3232EHCT-L/TR is a 3.3 V RS-232 transceiver with two transmitters and two receivers, a maximum data rate of 460 kbps, and a 16-pin SOIC package. Designed for portable and handheld equipment, the device provides the RS-232 line-driver and line-receiver functions required to connect a low-voltage controller to an external serial port. Its 3 V to 5.5 V supply range supports both 3.3 V and conventional 5 V system rails while allowing operation from sources as low as +2.7 V according to the manufacturer product page. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and restores incoming RS-232 signals to logic-compatible levels. It belongs to the interface IC hierarchy, where the RS-232 transceiver connects digital controllers, embedded systems, and industrial equipment to serial ports. The SP3232EH family specifically combines two drivers and two receivers in one package, reducing component count in compact serial-interface designs. The SP3232EHCT-L/TR operates from 3 V to 5.5 V and supports data rates up to 460 kbps. According to the manufacturer product page, it meets true EIA/TIA-232-F standards from a supply up to 5.5 V, remains interoperable with RS-232 when powered from a +2.7 V source, and provides enhanced ESD protection of ±15 kV using the human body model. These features suit interfaces exposed to electrostatic discharge through cables and external connectors. The 16-pin SOIC uses the SP3232EH transceiver arrangement, combining two transmit channels with two receive channels in a standard small-outline integrated-circuit footprint. This integration supports point-to-point serial links, diagnostic interfaces, service consoles, and embedded-control ports. The device also reduces board area compared with separate RS-232 driver and receiver packages while preserving the familiar point-to-point electrical interface. Typical applications include portable data-acquisition equipment, notebook and palmtop-class serial connectivity, industrial controllers, configuration interfaces, and instrumentation with RS-232 ports. Its 3.3 V compatibility is particularly useful where the host operates from a 3.3 V rail while the connector interface requires true RS-232 bipolar levels. Designers should place the transceiver close to the protected connector and route each transmit and receive path as a controlled interface network. Decoupling capacitors should be connected directly between the supply and ground pins with short traces. External protection components may improve system-level surge immunity, but their capacitance and clamping characteristics must be checked against the required 460 kbps data rate. This product page combines the manufacturer's SP3232EH family information, package and interface characteristics, practical application guidance, and same-package alternatives. It is intended to help engineers identify the correct electrical limits, verify replacement compatibility, and plan layout and protection before releasing a production design.

RFQ تماس
SP3232EHCY-L - Dual 3.3V RS-232 Transceiver | MaxLinear (Tape & Reel)
SP3232EHCY-L

SP3232EHCY-L - Dual 3.3V RS-232 Transceiver | MaxLinear (Tape & Reel)

The MaxLinear SP3232EHCY-L is a dual RS-232 transceiver with two transmitters and two receivers, a 3 V to 5.5 V supply range, and a maximum data rate of 460 kbps in a 16-pin TSSOP package. Designed for portable and handheld equipment, it combines full-duplex serial-interface capability with enhanced electrostatic-discharge protection. An RS-232 transceiver is an interface IC that converts between logic-level UART signals and the voltage levels used by RS-232 equipment. The broader hierarchy is transceiver, interface IC, and semiconductor. Within an RS-232 interface, the transmitters convert outgoing logic signals into RS-232 levels, while the receivers convert incoming RS-232 signals into logic-compatible levels. The SP3232EH family provides two drivers and two receivers in a single package. Its operating supply range of 3 V to 5.5 V supports both 3.3 V and 5 V systems. The device is intended for portable or handheld applications such as notebook and palmtop computers, where compact package size, low-voltage operation, and dependable line-driver performance are important. According to the manufacturer datasheet, the transceiver meets true EIA/TIA-232-F standards from a 5.5 V supply and remains interoperable with RS-232 when operated from a 2.7 V source. The enhanced ESD specification reaches 15 kV under the Human Body Model, helping protect the external RS-232 pins in user-accessible equipment. Typical uses include serial port interfaces, portable data-collection terminals, point-of-sale equipment, diagnostic equipment, and embedded systems that require two serial channels from one compact IC. The 16-pin TSSOP package reduces board area compared with larger dual-transceiver implementations while retaining separate transmit and receive channels. When laying out a circuit, keep RS-232 signal traces away from clocks, switching nodes, and high-current power paths. Confirm the host logic voltage, transceiver supply, and connector-side signal levels before assembly. Place the device near the protection network or connector when the PCB allows, and provide a continuous ground reference between the equipment and connected RS-232 system. This page combines the exact device attributes with practical interface guidance, package-focused alternatives, and engineering-oriented comparisons that help identify the correct RS-232 transceiver for a new design.

RFQ تماس
SP3232EHCY-L/TR - Dual 3.3V RS-232 Transceiver | MaxLinear
SP3232EHCY-L/TR

SP3232EHCY-L/TR - Dual 3.3V RS-232 Transceiver | MaxLinear

The MaxLinear SP3232EHCY-L/TR is a dual RS-232 transceiver with two transmitters and two receivers, a 3 V to 5.5 V supply range, and a maximum data rate of 460 kbps in a 16-pin TSSOP package. Designed for portable and handheld equipment, it combines full-duplex serial-interface capability with enhanced electrostatic-discharge protection. An RS-232 transceiver is an interface IC that converts between logic-level UART signals and the voltage levels used by RS-232 equipment. The broader hierarchy is transceiver, interface IC, and semiconductor. Within an RS-232 interface, the transmitters convert outgoing logic signals into RS-232 levels, while the receivers convert incoming RS-232 signals into logic-compatible levels. The SP3232EH family provides two drivers and two receivers in a single package. Its operating supply range of 3 V to 5.5 V supports both 3.3 V and 5 V systems. The device is intended for portable or handheld applications such as notebook and palmtop computers, where compact package size, low-voltage operation, and dependable line-driver performance are important. According to the manufacturer datasheet, the transceiver meets true EIA/TIA-232-F standards from a 5.5 V supply and remains interoperable with RS-232 when operated from a 2.7 V source. The enhanced ESD specification reaches 15 kV under the Human Body Model, helping protect the external RS-232 pins in user-accessible equipment. Typical uses include serial port interfaces, portable data-collection terminals, point-of-sale equipment, diagnostic equipment, and embedded systems that require two serial channels from one compact IC. The 16-pin TSSOP package reduces board area compared with larger dual-transceiver implementations while retaining separate transmit and receive channels. When laying out a circuit, keep RS-232 signal traces away from clocks, switching nodes, and high-current power paths. Confirm the host logic voltage, transceiver supply, and connector-side signal levels before assembly. Place the device near the protection network or connector when the PCB allows, and provide a continuous ground reference between the equipment and connected RS-232 system. This page combines the exact device attributes with practical interface guidance, package-focused alternatives, and engineering-oriented comparisons that help identify the correct RS-232 transceiver for a new design.

USD $0.22 موجود در انبار
SP3232EHEA-L/TR - 460kbps RS-232 Transceiver | MaxLinear
SP3232EHEA-L/TR

SP3232EHEA-L/TR - 460kbps RS-232 Transceiver | MaxLinear

MaxLinear SP3232EHEA-L/TR is a 2/2 full-duplex RS-232 transceiver designed for portable and handheld equipment. It supports data rates up to 460kbps from a 3V to 5.5V supply and is packaged in a 16-pin SSOP. The device includes two RS-232 drivers, two receivers, a high-efficiency charge-pump supply, and enhanced electrostatic-discharge protection rated at +15kV using the human body model. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and receives RS-232 signals back into logic-level outputs. It belongs to the serial-interface hierarchy, alongside UART controllers and isolation devices. This makes the SP3232EHEA-L/TR suitable for connecting a host, embedded controller, or industrial terminal to a legacy peripheral through a wired serial port. Key features include true EIA/TIA-232-F operation from a supply as low as +2.7V, interoperability with RS-232 equipment powered from +2.7V, a 460kbps maximum data rate, and 300mV receiver hysteresis. The charge-pump architecture requires only 0.1uF capacitors during 3.3V operation, reducing external component count in portable designs while preserving standard RS-232 signal levels. Internally, the dual-driver and dual-receiver arrangement supports two independent communication channels in full-duplex operation. Receiver hysteresis improves noise immunity around the logic threshold, while the enhanced ESD rating adds protection for connector-adjacent circuitry. The single-supply charge-pump design allows operation from modern 3.3V system rails without a separate negative RS-232 supply. Typical applications include point-of-sale terminals, portable data-collection equipment, industrial serial adapters, diagnostic interfaces, and battery-powered handheld computers. The 16-pin SSOP supports compact PCB layouts, while the 460kbps data rate accommodates legacy peripherals that require more speed than a conventional low-speed RS-232 link. When laying out the circuit, place charge-pump capacitors and the interface-side protection network close to their associated pins, and route the RS-232 connector path away from sensitive digital and analog traces. Confirm signal polarity and connector pin assignment before PCB release because RS-232 uses inverted logic in many controller implementations. This page combines the manufacturer's product information, exact-MPN distributor records, technical feature details, package information, practical design guidance, and same-family drop-in options. It is intended to help engineers identify the correct channel count, speed, supply range, package, and replacement path before committing a board layout.

RFQ تماس
SP3232EHEP-L - 3.3V 460kbps RS-232 Transceiver | MaxLinear
SP3232EHEP-L

SP3232EHEP-L - 3.3V 460kbps RS-232 Transceiver | MaxLinear

The MaxLinear SP3232EHEP-L is a 3.3 V RS-232 transceiver with two drivers, two receivers, and a maximum data rate of 460 kbps. The device is associated with a 16-pin TSSOP package and is intended for portable and hand-held equipment requiring a compact, low-power interface between TTL/CMOS logic and RS-232 lines. An RS-232 transceiver is an interface IC that combines differential line drivers and receivers with the voltage conversion required to communicate with RS-232 equipment. In the broader semiconductor hierarchy, it belongs to interface ICs and serves as the physical communication layer between a low-voltage digital controller and an RS-232 port. The SP3232EH family targets portable and hand-held applications such as notebook and laptop computers. The principal operating characteristics are a 3.3 V supply, two driver channels, two receiver channels, and throughput up to 460 kbps. These four features make the SP3232EHEP-L appropriate for point-to-point serial links, configuration ports, service interfaces, and embedded equipment that must exchange RS-232 signals without employing a larger multi-channel transceiver. MaxLinear describes the SP3232EH as a 2-driver/2-receiver RS-232 solution using a high-efficiency charge-pump power supply. According to the manufacturer data sheet, the charge-pump arrangement requires only 0.1 µF capacitors for 3.3 V operation. This architecture supports a compact external component set while maintaining the elevated and inverted voltage levels required by RS-232 driver outputs. Typical uses include portable data-acquisition equipment, industrial serial adapters, test fixtures, and controller boards with a legacy RS-232 service port. The 460 kbps rate supports substantially faster communication than conventional low-speed serial links while retaining the simple point-to-point interface of RS-232. System designers should still account for cable length, ground reference, transient protection, and protocol timing. When laying out the circuit, place the charge-pump capacitors and receiver bypass capacitors close to their associated device pins. Keep the RS-232 driver and receiver routes away from sensitive analog or high-speed digital paths, and provide the protection appropriate to the exposed connector environment. Follow the manufacturer data sheet for capacitor selection, pin assignments, and maximum operating conditions. This page consolidates the manufacturer specifications, package information, sourcing guidance, comparison points, and practical integration considerations for the SP3232EHEP-L. It is intended to help engineers identify a genuine same-footprint alternative, evaluate the 3.3 V and 460 kbps operating envelope, and plan a robust RS-232 interface before releasing the circuit to production.

RFQ تماس
SP3232EHET-L - 3.3V 460kbps RS-232 Transceiver | MaxLinear
SP3232EHET-L

SP3232EHET-L - 3.3V 460kbps RS-232 Transceiver | MaxLinear

MaxLinear SP3232EHET-L is a 3.3 V dual RS-232 transceiver with two drivers and two receivers, supporting data rates up to 460 kbps in a 16-pin SOIC package. It combines bidirectional serial-interface conversion with low-voltage operation for portable and embedded systems. The -L suffix identifies the lead-free ordering configuration, while the -TR portion is used by tape-and-reel order codes. An RS-232 transceiver is a level-shifting interface IC that converts logic-level signals from a host or controller into RS-232-compatible levels, while converting incoming RS-232 signals back into digital logic levels. In the interface hierarchy, SP3232EHET-L is a serial transceiver, an RS-232 transceiver, a line-driver and receiver pair, and ultimately a semiconductor interface device used between digital equipment and a cable-based serial port. The SP3232EH is designed around a compact 2/2 transceiver arrangement. Its 3.3 V supply operation reduces the logic-side voltage required by portable electronics, and its 460 kbps maximum signaling rate is suitable for moderate-speed serial links. The 16-SOIC format supports conventional surface-mount assembly while keeping the interface small enough for embedded control boards. Charge-pump circuitry and internal voltage levels allow the device to implement RS-232 signaling from a low-voltage supply. This transceiver architecture is intended for portable or hand-held equipment, including computers, terminals, and embedded serial-port systems. Two driver channels support two outgoing RS-232 signals, while two receiver channels accept two incoming signals. This arrangement suits equipment that needs more than one serial direction but does not require the channel count of larger multi-driver RS-232 families. Typical uses include point-of-sale terminals, portable diagnostic equipment, industrial controllers, and peripheral connection systems. In these applications, the key design considerations are the 3.3 V supply requirement, the 460 kbps data-rate ceiling, the 16-pin SOIC footprint, and the proper implementation of RS-232 cable protection. External protection may be required when a connected cable is exposed to electrostatic discharge or other industrial transients. Place bypass capacitors close to the supply and ground pins, route transceiver outputs and inputs away from sensitive clock or reference nets, and confirm that the host-side logic levels match the 3.3 V interface. Review the manufacturer pin-description and connection tables before assigning PCB tracks. Use the Request a Quote form on this page for current commercial availability, quantity requirements, and lead-time confirmation. This product page combines the manufacturer family description with distributor package and interface information, a pin-compatible replacement comparison, and practical PCB and protection guidance. It is intended to help engineers qualify the SP3232EHET-L quickly while still checking the exact ordering suffix against their mechanical and production requirements.

RFQ تماس
SP3232EHET-L/TR - 3.3V 460kbps RS-232 | MaxLinear
SP3232EHET-L/TR

SP3232EHET-L/TR - 3.3V 460kbps RS-232 | MaxLinear

MaxLinear SP3232EHET-L/TR is a 3.3V, 460kbps RS-232 transceiver containing two drivers and two receivers in a 16-SOIC package. The device operates from a 3V to 5.5V supply and supports RS-232 interoperability down to a 2.7V source. Enhanced human-body-model ESD protection of 15kV helps protect the serial interface when cables are connected to portable or hand-held equipment. The target is identified as a full RS-232, 2/2 transceiver and is packaged in the 16-SOIC format identified as 16-SOIC (0.295, 7.50mm width). An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts incoming RS-232 signals back into logic-compatible receiver outputs. The RS-232 transceiver category sits within serial interface ICs, interface ICs, and integrated circuits. It is commonly used to connect a host controller, embedded processor, test instrument, or industrial terminal to a longer-distance serial port where ground-referenced logic levels cannot drive the cable interface directly. The SP3232EH family provides two transmit drivers and two receive channels, allowing one port to support bidirectional RS-232 communication. Operation from a 3V to 5.5V supply is useful in portable systems operating from a 3.3V rail, while the 460kbps signaling capability supports higher-speed serial links than legacy low-speed RS-232 implementations. Its enhanced 15kV human-body-model ESD rating is a notable protection feature for connector-facing circuits. The architecture is optimized for portable and hand-held applications such as notebook and palmtop computers, where low supply voltage, compact packaging, and protection from electrostatic discharge are important. Because the device includes both directions of conversion, it can support two RS-232 lines without requiring separate driver and receiver ICs. The 16-SOIC package also provides a conventional surface-mount footprint compatible with automated assembly, although the exact pin assignment must be taken from the manufacturer pin-description table. Typical applications include portable data-collection equipment, serial adapters, industrial service interfaces, diagnostic equipment, and embedded control systems that retain an RS-232 port. When one side of a cable is exposed to user contact or poorly controlled external wiring, the 15kV human-body-model ESD rating is especially relevant. Designers should still provide appropriate protection-network coordination and verify that the selected connector, cable, and grounding arrangement meet the system-level interface requirements. The primary design consideration is power and signal integrity. Place the device close to the RS-232 connector so that board-trace exposure is minimized, connect the transceiver ground to the interface reference ground, and avoid long unprotected traces between the connector and IC. Confirm the 460kbps requirement against the actual cable length and noise environment because data rate, transmission distance, and capacitive loading are strongly related. This product page consolidates the core electrical ratings, package information, interface use cases, verified drop-in candidates, comparison parameters, and practical layout guidance for faster component selection and PCB planning. Use the MaxLinear SP3232EH product page and manufacturer datasheet for the authoritative electrical characteristics, recommended application circuit, and exact pin configuration.

RFQ تماس
SP3232EHEY-L - 460 kbps RS-232 Transceiver | MaxLinear (Tape & Reel)
SP3232EHEY-L

SP3232EHEY-L - 460 kbps RS-232 Transceiver | MaxLinear (Tape & Reel)

The MaxLinear SP3232EHEY-L is a 2-driver, 2-receiver RS-232 transceiver operating from a 3 V to 5.5 V single supply, supporting data rates up to 460 kbps in a 16-pin TSSOP package. The device includes a high-efficiency charge-pump supply and enhanced ESD protection rated to ±15 kV under the IEC human-body-model condition. Its integrated level conversion converts TTL/CMOS logic levels to and from RS-232 levels without requiring a separate supply for the interface rails. An RS-232 transceiver is a semiconductor interface device that bridges a digital logic system and a serial communications link using RS-232 voltage signaling. Each transceiver channel combines a line driver, which converts logic signals into RS-232 output levels, with a receiver, which converts incoming RS-232 signals into logic-compatible levels. In the broader hierarchy, the SP3232EHEY-L belongs to the interface-controller class, specifically the RS-232 driver/receiver and transceiver family within integrated interface ICs. The SP3232E series supports operation from a single 3.3 V supply while producing the positive and negative voltage levels required for conventional RS-232 communication. According to the MaxLinear manufacturer datasheet, its charge-pump supply requires only 0.1 µF capacitors in 3.3 V operation. The 2/2 driver and receiver arrangement provides two independent communications channels, while the 460 kbps maximum signaling rate supports common point-to-point serial links, embedded equipment, and legacy peripheral interfaces. The enhanced protection is particularly valuable in industrial and instrumentation environments where cables can be longer and more exposed than in a protected desktop enclosure. The device is specified for true EIA/TIA-232-F operation from a supply as high as 5.5 V and can interoperate with RS-232 equipment powered from a source as low as 2.7 V. Its internal charge-pump architecture reduces the number of external bulk capacitors while preserving bipolar RS-232 output levels. Typical applications include data acquisition equipment, industrial controllers, portable test instruments, point-of-sale terminals, and embedded systems that retain an RS-232 service or communications port. The device can also pair with a host UART or microcontroller to provide a standards-compliant physical interface for legacy equipment. Designers should treat the cable, ground reference, connector, and logic levels as parts of the complete communication path rather than relying only on the IC specification. A key design consideration is ensuring that the host-side interface levels match the selected UART and that unused driver or receiver channels are handled according to the manufacturer pin descriptions. Power-supply decoupling, charge-pump capacitor placement, and signal routing should follow the recommended layout in the manufacturer datasheet. ESD protection helps manage cable transients, but it does not replace proper grounding, shielding, or external surge protection in severe industrial environments. This product page combines the exact electrical ratings, package information, pin-location guidance, verified drop-in candidates, and practical interface-layout considerations for SP3232EHEY-L. It also distinguishes genuine same-footprint replacements from functionally similar devices that use different packages, allowing engineers to evaluate compatibility before modifying an existing RS-232 design.

USD $0.22 موجود در انبار
SP3232EHEY-L/TR - 460 kbps RS-232 Transceiver | MaxLinear
SP3232EHEY-L/TR

SP3232EHEY-L/TR - 460 kbps RS-232 Transceiver | MaxLinear

The MaxLinear SP3232EHEY-L/TR is a 2-driver, 2-receiver RS-232 transceiver operating from a 3 V to 5.5 V single supply, supporting data rates up to 460 kbps in a 16-pin TSSOP package. The device includes a high-efficiency charge-pump supply and enhanced ESD protection rated to ±15 kV under the IEC human-body-model condition. Its integrated level conversion converts TTL/CMOS logic levels to and from RS-232 levels without requiring a separate supply for the interface rails. An RS-232 transceiver is a semiconductor interface device that bridges a digital logic system and a serial communications link using RS-232 voltage signaling. Each transceiver channel combines a line driver, which converts logic signals into RS-232 output levels, with a receiver, which converts incoming RS-232 signals into logic-compatible levels. In the broader hierarchy, the SP3232EHEY-L/TR belongs to the interface-controller class, specifically the RS-232 driver/receiver and transceiver family within integrated interface ICs. The SP3232E series supports operation from a single 3.3 V supply while producing the positive and negative voltage levels required for conventional RS-232 communication. According to the MaxLinear manufacturer datasheet, its charge-pump supply requires only 0.1 µF capacitors in 3.3 V operation. The 2/2 driver and receiver arrangement provides two independent communications channels, while the 460 kbps maximum signaling rate supports common point-to-point serial links, embedded equipment, and legacy peripheral interfaces. The enhanced protection is particularly valuable in industrial and instrumentation environments where cables can be longer and more exposed than in a protected desktop enclosure. The device is specified for true EIA/TIA-232-F operation from a supply as high as 5.5 V and can interoperate with RS-232 equipment powered from a source as low as 2.7 V. Its internal charge-pump architecture reduces the number of external bulk capacitors while preserving bipolar RS-232 output levels. Typical applications include data acquisition equipment, industrial controllers, portable test instruments, point-of-sale terminals, and embedded systems that retain an RS-232 service or communications port. The device can also pair with a host UART or microcontroller to provide a standards-compliant physical interface for legacy equipment. Designers should treat the cable, ground reference, connector, and logic levels as parts of the complete communication path rather than relying only on the IC specification. A key design consideration is ensuring that the host-side interface levels match the selected UART and that unused driver or receiver channels are handled according to the manufacturer pin descriptions. Power-supply decoupling, charge-pump capacitor placement, and signal routing should follow the recommended layout in the manufacturer datasheet. ESD protection helps manage cable transients, but it does not replace proper grounding, shielding, or external surge protection in severe industrial environments. This product page combines the exact electrical ratings, package information, pin-location guidance, verified drop-in candidates, and practical interface-layout considerations for SP3232EHEY-L/TR. It also distinguishes genuine same-footprint replacements from functionally similar devices that use different packages, allowing engineers to evaluate compatibility before modifying an existing RS-232 design.

USD $0.22 موجود در انبار
SP3232EN-L - 3V RS-232 Transceiver | MaxLinear | Serial Interface
SP3232EN-L

SP3232EN-L - 3V RS-232 Transceiver | MaxLinear | Serial Interface

The MaxLinear SP3232EN-L is a 2-transceiver, full-duplex RS-232 interface IC designed for portable and hand-held equipment. According to the supplied distributor and manufacturer-linked data, it operates from a true +3.0 V to +5.5 V supply, supports data rates up to 120 kbps under full load, and is available in a 16-pin SOIC package. The -L suffix identifies the lead-free ordering option, while the verified listings distinguish this MPN from SP3232EEN-L and other orderable variants. An RS-232 transceiver is an interface IC that converts between logic-level TTL/CMOS signals and the voltage-defined, single-ended differential signaling used by RS-232 equipment. This device integrates transmit and receive channels, allowing two serial directions to share one physical interface. It is commonly selected for battery-powered, portable, industrial-control, and legacy equipment connections where a compact, low-voltage serial interface is required. The SP3232EN-L is specified for a 3.0 V to 5.5 V operating supply range and a maximum data rate of 120 kbps under full load. The supplied specifications also identify approximately 1 mA supply current, low-power shutdown capability with receivers active for the relevant SP3222E family description, and operation from -40 C to +85 C. Its RS-232 interface is intended for portable or hand-held applications such as notebook and palmtop computers. The 16-pin SOIC package provides a conventional surface-mount footprint suitable for compact PCB assemblies. Because this is an interface transceiver rather than a power semiconductor, the safe-operating-area field is not applicable. Exact pin names, pinout details, receiver and transmitter electrical limits, and some lifecycle and compliance fields were not present in the supplied verified snippets; those values should be checked against the manufacturer datasheet before production release. Typical applications include RS-232 links in portable data-acquisition equipment, handheld test instruments, embedded controllers with legacy serial ports, and battery-operated peripherals. The 120 kbps rate is suitable for moderate-speed serial communication rather than high-bandwidth protocols. When designing the interface, account for the RS-232 voltage levels, cable capacitance, grounding strategy, protection requirements, and the difference between logic-level and RS-232-side pins. This page consolidates the verified SP3232EN-L distributor records, identified technical specifications, application guidance, and design cautions into one engineering reference. It is intended to support part selection and preliminary design work; final component validation should use the current manufacturer datasheet and approved sourcing channels.

RFQ تماس
SP3232EP-L - 3.0V RS-232 Transceiver | Sipex
SP3232EP-L

SP3232EP-L - 3.0V RS-232 Transceiver | Sipex

The Sipex SP3232EP-L is a +3.0V to +5.5V RS-232 transceiver designed for low-voltage serial interfaces. The verified manufacturer material identifies a minimum data rate of 120 kbps under full load, operation from a true +3.0V to +5.5V supply, compatibility with RS-232 down to +2.7V, and enhanced ESD protection rated at ±15 kV. The available SP3232EP family is offered in a 16-pin SSOP package, matching the selected SSOP-16 footprint and supporting PCB-level drop-in evaluation for compatible RS-232 designs. What is an RS-232 transceiver? An RS-232 transceiver is an interface IC that combines a driver and receiver for point-to-point serial communication. In the wider hierarchy, it is a transceiver, then an interface IC, then an integrated circuit and semiconductor. The driver converts logic-level signals into RS-232 levels, while the receiver converts incoming RS-232 levels back into digital logic levels. This device is intended for systems that need standards-based serial connectivity at low supply voltage. Key features include the 3.0V minimum operating supply, 5.5V maximum supply, 120 kbps minimum data rate under full load, and ±15 kV enhanced ESD protection. The verified snippets also identify true EIA/TIA-232-F compliance from a +3.0V to +5.5V supply and interoperability with RS-232 down to +2.7V. These characteristics make the transceiver suitable for embedded systems, industrial control links, test equipment, and peripheral connections where a standard RS-232 interface is required. The SP3232EP uses a +3.0V-to-+5.5V supply architecture to support low-voltage digital systems without requiring a higher-voltage RS-232 transceiver supply. The 120 kbps minimum rate under full load provides a defined data-rate target for moderate-speed serial links. Its ESD rating is particularly important because RS-232 connector inputs can be exposed to external cables and user-contact transients. Typical applications include USB-to-RS-232 adapters, embedded instrumentation, point-of-sale equipment, industrial controllers, data-acquisition systems, and legacy peripheral connections. In each case, the transceiver provides the physical-layer interface between logic-level UART hardware and an external RS-232 port. The application must still observe the datasheet's electrical limits, pin connections, decoupling requirements, and cable-routing guidance. For PCB design, place the transceiver close to the RS-232 connector and provide the required local supply bypassing. Keep the logic-side traces away from the connector-side signals, use an appropriate ground reference, and verify the external UART voltage levels. The 16-pin SSOP footprint requires careful solder-paste and land-pattern review before manufacturing. This page combines verified manufacturer and distributor information, pricing context, package identification, and application-focused engineering guidance. Because the supplied web results do not provide a complete pin-by-pin pinout or verified same-package substitute list, missing engineering data is explicitly marked rather than inferred. Confirm final placement and production quantities against the manufacturer datasheet and current distributor inventory.

RFQ تماس
SP3232EUCA-L - 3.3V 1Mbps RS-232 IC | MaxLinear
SP3232EUCA-L

SP3232EUCA-L - 3.3V 1Mbps RS-232 IC | MaxLinear

The MaxLinear SP3232EUCA-L is a 3.3 V RS-232 interface IC containing two drivers and two receivers, supporting data rates up to 1000 kbps in a 16-SSOP package. Its integrated charge-pump supply supports low-capacitance operation with 0.1 µF capacitors in 3.3 V applications, reducing the external support-component count for compact serial-interface designs. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts received RS-232 signals back into digital logic. The SP3232EU belongs to the broader line-driver and line-receiver hierarchy, where the line driver transmits, the line receiver detects, and the transceiver combines both functions. It is particularly relevant to portable and handheld equipment requiring bidirectional asynchronous serial communication. The principal features include two transmit drivers, two receive receivers, full RS-232 operation, a 3.3 V supply, and a maximum data transmission rate of 1000 kbps. The 1000 kbps rating supports high-speed RS-232 links, while the two-driver and two-receiver arrangement allows two serial channels or a combination of independent transmit and receive paths. The 16-SSOP package also supports compact board layouts where a larger SOIC footprint would be undesirable. The internal high-efficiency charge pump generates the bipolar voltage required by the RS-232 drivers without requiring an external negative supply. According to the MaxLinear SP3232EU product information, 3.3 V operation requires only 0.1 µF charge-pump capacitors. This architecture simplifies system partitioning, although the external capacitor selection, placement, and tolerance still influence driver amplitude and signal integrity. Typical uses include portable data terminals, handheld test equipment, industrial serial adapters, embedded serial consoles, and compact peripheral interfaces. The two transmitters and two receivers are useful when a design needs more than one RS-232 direction, while the 1000 kbps capability can accommodate short-distance high-speed links when the connected equipment, cable, and protocol support that rate. PCB design should follow the manufacturer pin and capacitor-placement guidance, keep charge-pump and receiver-network components close to the device, and provide adequate return paths for both supply rails. The RS-232 interface must also be evaluated for ground offset, cable length, connector protection, and transient immunity; a high logic data rate does not guarantee reliable communication on every cable or grounding arrangement.

RFQ تماس
SP3232EUCA-L/TR - 3.3V 1Mbps RS-232 IC | MaxLinear
SP3232EUCA-L/TR

SP3232EUCA-L/TR - 3.3V 1Mbps RS-232 IC | MaxLinear

The MaxLinear SP3232EUCA-L/TR is a 3.3 V RS-232 transceiver IC with two drivers, two receivers, and a maximum data rate of 1000 kbps, packaged in a 16-pin SSOP. The device provides the electrical interface between a low-voltage digital system and an RS-232 port, combining bidirectional line-driver and line-receiver functions in one package. According to the MaxLinear product page, the SP3232EU is intended for portable and handheld equipment while also supporting high-speed RS-232 data transmission. An RS-232 transceiver is an interface IC that translates digital logic levels into RS-232 line levels and converts received RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy alongside serial transceivers, line drivers, and line receivers. These devices simplify serial-port design by combining the active driver circuitry, receiver circuitry, and the required charge-pump voltage conversion in a single IC. The SP3232EU operates from a 3 V to 5.5 V supply and supports data rates up to 1000 kbps. Its two-driver and two-receiver arrangement can serve two communication channels or provide additional driver and receiver channels for handshake and control signals. The 3.3 V operating capability makes the device suitable for systems based on modern low-voltage microcontrollers, embedded processors, and portable equipment. MaxLinear identifies true EIA/TIA-232-F operation from a supply as high as 5.5 V. Its internal high-efficiency charge-pump supply generates the voltage required by the RS-232 drivers while allowing operation with only 0.1 uF external capacitors in 3.3 V designs. This approach reduces external component count compared with implementations that require additional bulk capacitance. The SP3232EU therefore combines a compact SSOP-16 footprint with a high data rate and low-voltage operation. Typical uses include portable-computer accessories, handheld equipment, industrial serial interfaces, point-of-sale terminals, instrument connections, and embedded-control systems. In an embedded design, the transceiver can connect a 3.3 V controller UART to an external RS-232 connector while preserving the logic-level translation required by the RS-232 standard. Layout should keep the charge-pump capacitors and communication-line protection close to their associated pins, while separating the transceiver from sensitive analog or high-speed digital circuits. Confirm the package pin assignments and connector signal mapping in the manufacturer datasheet before PCB release. This product page combines the MaxLinear family specifications, verified distributor listings, package details, and practical selection guidance. It also distinguishes same-family alternatives by verified electrical ratings and package information so engineers can assess replacement suitability without treating merely similar components as drop-in replacements.

RFQ تماس
SP3232EUCN-L - 1 Mbps Dual RS-232 Transceiver | MaxLinear
SP3232EUCN-L

SP3232EUCN-L - 1 Mbps Dual RS-232 Transceiver | MaxLinear

The MaxLinear SP3232EUCN-L is a 3.3 V RS-232 transceiver with two drivers and two receivers, a 1000 kbps data rate, and a 16-pin SOIC package. Designed for portable and handheld equipment, it combines bidirectional RS-232 interface conversion with an integrated charge-pump power supply. The 0C to 70C commercial temperature range supports industrial, consumer, and point-of-use equipment where a compact, low-voltage serial interface is required. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 voltage levels and converts received RS-232 signals back into logic-compatible levels. The SP3232EUCN-L belongs to the RS-232 transceiver hierarchy, where transceiver ICs sit between host processors or microcontrollers and external D-sub or other RS-232 connectors. Its two driver and two receiver channels permit simultaneous bidirectional communication while reducing the external component count required for level conversion. The device supports data transmission at up to 1000 kbps and operates from a 3.3 V supply. According to the manufacturer datasheet, its high-efficiency charge-pump supply requires only 0.1 uF capacitors for 3.3 V operation. This compact charge-pump arrangement supports compact portable designs while producing the bipolar voltage levels required by RS-232. The package also reduces board area compared with discrete driver and receiver implementations. The SP3232EU family provides separate transmit and receive channels, allowing a system to send and receive RS-232 data through one interface IC. The receiver channels support integration with UART-based controllers, while the drivers connect to external RS-232 ports. Its 1000 kbps capability is suitable for moderate-speed diagnostic, configuration, control, and point-of-service interfaces rather than long-distance continuous high-bandwidth data links. Typical uses include handheld test equipment, portable computers, serial adapters, point-of-sale terminals, industrial service interfaces, and embedded control systems that exchange configuration or diagnostic data through RS-232. The 16-pin SOIC package is particularly useful where a conventional through-hole or larger surface-mount footprint would be inconvenient. When designing around the SP3232EUCN-L, place the charge-pump capacitors close to their designated pins and route the RS-232 driver outputs directly toward the connector. Keep logic-side traces away from the high-voltage transmit nets, provide the connector's normal ESD and surge-protection path, and verify that the connected UART baud rate and cable loading are compatible with 1000 kbps operation. This page combines the manufacturer interface characteristics, package details, application guidance, verified drop-in alternatives, and practical PCB considerations to support faster component selection and implementation planning.

RFQ تماس
SP3232EUCN-L/TR - 1 Mbps 3.3V RS-232 | MaxLinear
SP3232EUCN-L/TR

SP3232EUCN-L/TR - 1 Mbps 3.3V RS-232 | MaxLinear

MaxLinear SP3232EUCN-L/TR is a 3.3 V RS-232 transceiver IC with two drivers, two receivers, a maximum data rate of 1000 kbps, and a 16-pin SOIC package. It supports portable and hand-held equipment that requires bidirectional serial communication using the RS-232 interface. The integrated high-efficiency charge-pump supply supports 3.3 V operation with only 0.1 µF capacitors. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 voltage levels and converts received RS-232 signals back into logic-compatible levels. Within the interface hierarchy, it is a serial transceiver, a line-driver and line-receiver component, and ultimately a semiconductor designed for data communication and industrial-control equipment. The SP3232E has two transmit channels and two receive channels, allowing two serial links or bidirectional operation on one device. Its 1000 kbps signaling rate supports relatively high-speed RS-232 communication compared with slower legacy transceivers. Operation from a single 3.3 V supply also simplifies power design in portable systems, while the charge-pump topology generates the bipolar voltage required by RS-232 without a separate negative supply. MaxLinear describes the SP3232E series as a solution for portable or hand-held computers, including notebook and palmtop platforms. The same architecture is useful for instrument control, point-of-sale equipment, industrial serial adapters, and embedded systems that exchange data with a host over RS-232. The charge-pump network requires small 0.1 µF capacitors for 3.3 V operation. Place these capacitors close to their associated pins and keep the RS-232 driver and receiver traces away from sensitive analog or high-speed digital paths. Confirm the exact pin names and exposed functions against the MaxLinear datasheet before assigning PCB nets. This product page combines the SP3232E family electrical characteristics, package information, drop-in replacement guidance, comparison data, and practical PCB design notes to support faster component selection and implementation.

RFQ تماس
SP3232EUCT-L - 1 Mbps Dual RS-232 Transceiver | MaxLinear
SP3232EUCT-L

SP3232EUCT-L - 1 Mbps Dual RS-232 Transceiver | MaxLinear

The MaxLinear SP3232EUCT-L is a dual-driver, dual-receiver RS-232 transceiver designed for high-speed serial communication from a single 3.0 V to 5.5 V supply. It supports a maximum data rate of 1000 kbps and is packaged in a 16-pin SOIC for compact industrial, communications, and embedded equipment. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible levels. The SP3232E family integrates two line drivers, two line receivers, and a charge-pump supply, placing it within the hierarchy of interface ICs, communications transceivers, and RS-232 interface silicon. The SP3232EUCT-L provides two transmit channels and two receive channels, allowing one RS-232 port to handle two data directions. Its single-supply operation supports both 3.3 V and 5 V system environments. The manufacturer's charge-pump design requires only 0.1 uF capacitors in 3.3 V operation, reducing external component count while preserving full RS-232 signal levels. Its 1000 kbps capability is suitable for moderate-speed serial links, including embedded control ports and industrial peripherals. The integrated charge pump generates the positive and negative voltages needed by RS-232 drivers from the single supply. This architecture avoids a separate bipolar power source and allows the device to operate from a 3.0 V to 5.5 V source. Because the interface performs level translation at the physical layer, the connected host or target UART still handles data framing, baud-rate agreement, parity, flow control, and protocol behavior. Typical uses include industrial control equipment, portable data-acquisition systems, service interfaces, POS terminals, and embedded debug or configuration ports. The 16-pin SOIC package supports conventional surface-mount assembly and remains practical for boards where component height is more constrained than the size of a dual-inline package. Confirm the exact pin assignment, charge-pump capacitor values, and decoupling requirements in the manufacturer datasheet before PCB release. Preserve short, direct paths for the charge-pump nodes and place the required capacitors close to their associated pins to reduce switching noise and unstable driver behavior. This product page combines the SP3232EUCT-L electrical characteristics, same-package replacement options, application guidance, and design notes to help engineers evaluate the transceiver quickly and implement a reliable RS-232 interface.

RFQ تماس
SP3232EUCT-L/TR - 2/2 RS-232 Transceiver | MaxLinear
SP3232EUCT-L/TR

SP3232EUCT-L/TR - 2/2 RS-232 Transceiver | MaxLinear

The MaxLinear SP3232EUCT-L/TR is a 2-driver, 2-receiver RS-232 transceiver designed for portable and high-speed serial-interface equipment. It operates from a single 3 V to 5.5 V supply, supports data rates up to 1000 kbps, and uses an efficient charge-pump power supply that requires only 0.1 µF capacitors in 3.3 V operation. The device is packaged in a 16-pin SOIC for surface-mount assembly. An RS-232 transceiver is an interface IC that combines voltage-level conversion, drivers, and receivers to connect modern low-voltage digital logic with legacy RS-232 equipment. The SP3232EU family provides a practical bridge between UART controllers and serial peripherals, printers, industrial instruments, and point-of-sale terminals. Its compact surface-mount package supports automated assembly while avoiding a separate external RS-232 line-driver circuit. Principal features include two transmit drivers and two receive receivers, operation from one 3 V to 5.5 V supply, and a maximum data transmission rate of 1000 kbps. The internal charge-pump design supplies the bipolar voltage levels required by RS-232 without a separate negative supply. At 3.3 V, the charge pump requires only 0.1 µF capacitors, reducing external component count and helping conserve board space in portable equipment. The SP3232EUCT-L/TR is the tape-and-reel ordering form of the SP3232EUCT-L device. Its 16-SOIC package is suitable for reflow assembly and volume manufacturing. The suffix /TR identifies tape-and-reel packing, while U identifies the electrical and temperature configuration and L identifies the lead-free ordering option. Design engineers should use the manufacturer pin-description table when assigning connector-side and logic-side nets. Typical applications include notebook and palmtop computer serial ports, portable data-collection equipment, industrial serial adapters, barcode scanners, point-of-sale terminals, and embedded diagnostic interfaces. The device is especially useful where a low-voltage UART must connect to an RS-232 port using one compact transceiver rather than discrete level-shifting circuitry. The principal design considerations are external capacitor selection, signal grounding, and RS-232 protection. Place the charge-pump capacitors and interface bypass capacitors close to their specified pins, and route the RS-232 traces away from sensitive analog or high-speed digital nets. The receive path should also be evaluated for system-level ESD protection where cables leave the enclosure. This page combines the manufacturer device information, practical package and application guidance, drop-in replacement considerations, and design notes intended to shorten component-selection and PCB-integration time.

RFQ تماس
SP3232EUCY-L/TR - 1Mbps Dual RS-232 Transceiver | MaxLinear
SP3232EUCY-L/TR

SP3232EUCY-L/TR - 1Mbps Dual RS-232 Transceiver | MaxLinear

MaxLinear SP3232EUCY-L/TR is a 2-driver, 2-receiver RS-232 interface transceiver capable of transmitting at 1000 kbps. It operates from a single 3 V to 5.5 V supply, supports 3.3 V operation, and is packaged in a 16-pin TSSOP. The -L designation identifies the low-power variant, while the /TR suffix denotes tape-and-reel shipping. An RS-232 transceiver is a semiconductor interface device that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into digital logic. It belongs to the line-transceiver hierarchy within interface ICs and provides the physical signaling layer required to connect a data-processing system to a serial peripheral over RS-232. The SP3232EUCY-L/TR provides two transmit channels and two receive channels, allowing two full-duplex serial links on one device. Its maximum data rate of 1000 kbps supports high-speed RS-232 communication, while the 3 V to 5.5 V supply range accommodates both 3.3 V and 5 V system rails. The internal charge-pump supply supports true RS-232 operation without a separate bipolar supply when the device operates from 3.3 V. MaxLinear describes the SP3232EU family as a high-efficiency charge-pump solution for portable and hand-held equipment. The charge-pump topology raises and inverts the supply used by the line drivers, while the receiver and driver channels implement the voltage translation required by RS-232. The family is intended for equipment where compact implementation, low component count, and reliable serial connectivity are important. Typical uses include notebook and palmtop computer serial interfaces, portable data-collection equipment, industrial control systems, instrument interfaces, and embedded serial links. A design can place the transceiver between a host UART and an external DB9 or other RS-232 connector, adding the required logic-to-RS-232 level conversion while preserving a compact surface-mount footprint. PCB layout is important around this interface. Keep charge-pump capacitors and supply bypass components close to their associated pins, route the RS-232 driver outputs away from sensitive logic, and use an appropriate protection scheme for cables connected to external equipment. The 16-pin TSSOP package is pin-compatible with the closely related SP3232ECY-L/TR member of the same device family. This page combines the manufacturer specifications, interface-family context, replacement guidance, and practical layout considerations into a focused engineering reference. It also distinguishes exact package compatibility from broader RS-232 functionality so that designers can assess a replacement without assuming that every similar transceiver has the same footprint or signaling performance.

RFQ تماس