محصولات (46,000+)

SP490EEP-L - 10Mbps Full-Duplex RS-485/422 | MaxLinear
SP490EEP-L

SP490EEP-L - 10Mbps Full-Duplex RS-485/422 | MaxLinear

MaxLinear SP490EEP-L is a 1-transceiver, full-duplex RS-485 and RS-422 interface IC that supports differential data rates up to 10 Mbps and is supplied in an 8-pin plastic DIP package. The device combines one differential line driver and one differential line receiver on the same package, allowing bidirectional point-to-point communication without half-duplex bus-direction control. According to the MaxLinear SP490E/SP491E datasheet, the receiver input sensitivity is ±200 mV over a wide common-mode range. The SP490EEP-L is the SP490E full-duplex configuration; unlike SP491E devices, the SP490E does not provide separate driver and receiver tri-state enable inputs. This distinction makes the SP490EEP-L appropriate for RS-422 links and full-duplex RS-485 point-to-point or multipoint arrangements where the line state is managed by the surrounding system rather than local enable pins. The 8-PDIP format facilitates prototyping, legacy industrial control, and manually assembled systems where a through-hole package is easier to inspect and replace. Its low-power BiCMOS implementation supports low-power communication equipment while retaining the data rate required by industrial links, instrumentation, and embedded serial interfaces. The datasheet material also identifies compatibility with LTC490-class interfaces, but every replacement must be checked for enable behavior, supply requirements, receiver thresholds, and package-specific pin mapping before design release.

RFQ تماس
SP490EN-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear
SP490EN-L

SP490EN-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear

The MaxLinear SP490EN-L is a low-power differential line transceiver supporting RS-485 and RS-422 communication at data rates up to 5 Mbps, with one transmitter and one receiver in an 8-pin narrow SOIC package. It operates from a 5 V supply, provides ±200 mV receiver input sensitivity, and is specified for commercial temperature operation from -40°C to +85°C. An RS-485/RS-422 transceiver is an interface IC that converts single-ended logic signals into differential signals for balanced wired communication and converts received differential signals back into logic-level data. The differential signal path improves noise immunity and allows communication across longer cable runs than ordinary single-ended interfaces. SP490EN-L sits within the interface-IC hierarchy as a bus transceiver for industrial, instrumentation, and data-communication equipment. The SP490EN-L combines one differential driver and one differential receiver in a full-duplex arrangement. Its low-power BiCMOS implementation is intended for 5 V systems and supports data rates up to 5 Mbps. The receiver sensitivity of ±200 mV helps recognize small differential signals, while the wide common-mode range allows useful operation in electrically noisy environments when the board and cabling are designed appropriately. The SP491 is identified by the datasheet as functionally similar but adds driver and receiver tri-state enable lines, so it is not used as a direct substitute here. Typical applications include RS-485 field-bus links, industrial control and test equipment, point-to-point RS-422 links, data acquisition systems, and communication links between separated circuit boards. The full-duplex arrangement is useful where transmit and receive paths must operate independently, although the SP490EN-L does not provide the explicit tri-state enable controls associated with SP491. Cable length and data rate must be selected together because transmission-line losses, termination, stub effects, and common-mode limits can reduce the usable cable distance. For PCB design, keep the differential pair impedance-controlled and route the driver and receiver connections according to the system’s cable and termination strategy. Place termination and protection components close to the transceiver pins, and verify that the selected protection network does not degrade the receiver’s differential sensitivity or data-rate margin. Power-supply bypassing should be placed directly beside the device supply pins. The verified data does not provide exact absolute maximum ratings, propagation-delay limits, receiver common-mode limits, or package dimensions, so those values should be taken from the MaxLinear datasheet before final design release.

RFQ تماس
SP490EN-L/TR - 5Mbps RS-485/RS-422 Transceiver | MaxLinear (Tape & Reel)
SP490EN-L/TR

SP490EN-L/TR - 5Mbps RS-485/RS-422 Transceiver | MaxLinear (Tape & Reel)

The MaxLinear SP490EN-L/TR is a low-power differential line transceiver supporting RS-485 and RS-422 communication at data rates up to 5 Mbps, with one transmitter and one receiver in an 8-pin narrow SOIC package. It operates from a 5 V supply, provides ±200 mV receiver input sensitivity, and is specified for commercial temperature operation from -40°C to +85°C. An RS-485/RS-422 transceiver is an interface IC that converts single-ended logic signals into differential signals for balanced wired communication and converts received differential signals back into logic-level data. The differential signal path improves noise immunity and allows communication across longer cable runs than ordinary single-ended interfaces. SP490EN-L/TR sits within the interface-IC hierarchy as a bus transceiver for industrial, instrumentation, and data-communication equipment. The SP490EN-L/TR combines one differential driver and one differential receiver in a full-duplex arrangement. Its low-power BiCMOS implementation is intended for 5 V systems and supports data rates up to 5 Mbps. The receiver sensitivity of ±200 mV helps recognize small differential signals, while the wide common-mode range allows useful operation in electrically noisy environments when the board and cabling are designed appropriately. The SP491 is identified by the datasheet as functionally similar but adds driver and receiver tri-state enable lines, so it is not used as a direct substitute here. Typical applications include RS-485 field-bus links, industrial control and test equipment, point-to-point RS-422 links, data acquisition systems, and communication links between separated circuit boards. The full-duplex arrangement is useful where transmit and receive paths must operate independently, although the SP490EN-L/TR does not provide the explicit tri-state enable controls associated with SP491. Cable length and data rate must be selected together because transmission-line losses, termination, stub effects, and common-mode limits can reduce the usable cable distance. For PCB design, keep the differential pair impedance-controlled and route the driver and receiver connections according to the system’s cable and termination strategy. Place termination and protection components close to the transceiver pins, and verify that the selected protection network does not degrade the receiver’s differential sensitivity or data-rate margin. Power-supply bypassing should be placed directly beside the device supply pins. The verified data does not provide exact absolute maximum ratings, propagation-delay limits, receiver common-mode limits, or package dimensions, so those values should be taken from the MaxLinear datasheet before final design release.

RFQ تماس
SP490ES-L - 5Mbps Full-Duplex RS-485/RS-422 | MaxLinear
SP490ES-L

SP490ES-L - 5Mbps Full-Duplex RS-485/RS-422 | MaxLinear

MaxLinear SP490ES-L is a low-power, full-duplex differential line transceiver combining one RS-485/RS-422 driver and one receiver in an 8-pin plastic DIP package. It supports signaling rates up to 5Mbps from a 5V supply and provides receiver input sensitivity of ±200mV over a wide common-mode range. The SP490ES-L is packaged in an 8-pin plastic DIP, also identified as an 8-DIP package with a 7.62mm lead pitch. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into differential electrical signals for reliable communication over longer cable distances. RS-422 supports point-to-point, full-duplex differential signaling, while RS-485 supports multipoint buses and commonly uses half-duplex arrangements. The SP490 family supports both standards and is positioned for industrial-control, instrumentation, data-acquisition, and embedded communications systems. Key features include one driver and one receiver, operation up to 5Mbps, a 5V supply requirement, ±200mV receiver sensitivity, and a wide receiver common-mode range. The differential signal path improves noise immunity by comparing the voltage difference between two conductors rather than relying on a single-ended voltage referenced only to ground. The full-duplex architecture supports separate transmit and receive paths. The SP490ES-L is identified in distributor data as a 1/1 full-duplex transceiver in an 8-PDIP package. Its 8-pin DIP format is useful for through-hole industrial and legacy-style assemblies where a surface-mount package is not desired. The SP490 family is also offered in 8-pin NSOIC packages according to the manufacturer product page, but the SP490ES-L ordering code specifically corresponds to the 8-pin plastic DIP package. Typical applications include RS-485 field buses, factory automation equipment, motor-control systems, building controls, industrial sensors, data loggers, and embedded serial interfaces. Design attention should be paid to termination, biasing, cable length, grounding, and the relationship between data rate and transmission distance. Differential routing should be kept balanced and separated from noisy switching nodes. This page combines verified manufacturer and distributor information with practical design guidance for engineers evaluating the SP490ES-L. It also distinguishes the verified 5V, 5Mbps, ±200mV sensitivity, full-duplex, and 8-DIP characteristics from specifications that require confirmation from the complete manufacturer datasheet before release to production.

RFQ تماس
SPAK56F803BU80 - DSP56F803 16-bit DSP, 80MHz, 100-LFQFP | NXP
SPAK56F803BU80

SPAK56F803BU80 - DSP56F803 16-bit DSP, 80MHz, 100-LFQFP | NXP

The NXP (formerly Freescale/Motorola) SPAK56F803BU80 is a 16-bit Digital Signal Processor from the DSP56F803 family, delivering up to 40 MIPS at an 80 MHz core frequency in a 100-pin LFQFP (Low-profile Fine-pitch Quad Flat Pack) gull-wing surface-mount package. It is an industrial-temperature-grade part, optimized for embedded motor control and digital signal processing applications that require deterministic MCU-style control combined with DSP throughput. A DSP (Digital Signal Processor) is a specialized microprocessor whose architecture is tuned for the repetitive, high-throughput numerical operations (multiply-accumulate, FIR/IIR filtering, FFTs, PID loops) that overwhelm a general-purpose MCU. The DSP56F803 unifies DSP and MCU functionality in a single C-efficient core, exposing bit-manipulation instructions, hardware DO/REP loops, a 14-addressing-mode instruction set, and a MAC unit so a single chip can run both control code and signal-processing kernels without a dual-core architecture. Key features include a 40 MIPS core, on-chip program and data memory, integrated peripherals (PWMs, ADCs, timers, communication ports), and an industrial operating temperature range. The 100-pin LFQFP package provides ample I/O for motor-control and power-conversion designs while using a 1.0 mm or 0.5 mm gull-wing lead pitch compatible with standard reflow and fine-pitch assembly lines. Technically, the DSP56F803 family is built on a Harvard-style architecture with separate program and data buses, dual on-chip RAM blocks, and a peripheral set including PWM modules for 3-phase motor control. Code development is supported by the Freescale/NXP CodeWarrior toolchain and the Processor Expert configuration environment, enabling rapid prototyping in C and assembly. Typical applications include AC induction motor drives, BLDC/PMSM servo control, industrial inverters, uninterruptible power supplies (UPS), and audio/sensor signal conditioning. The industrial temperature grade and on-chip peripherals reduce BOM cost in motor-control designs. Design consideration: when laying out the 100-pin LFQFP, place decoupling capacitors within 5 mm of each supply pin and provide a continuous ground pour beneath the package to keep switching-noise from coupling into the analog ADC inputs. This page synthesizes distributor pricing for the SPAK56F803BU80, drop-in LFQFP-100 alternatives, and practical design notes not found in the manufacturer datasheet, making it easier to evaluate and source the part for new designs and legacy reorders.

RFQ تماس
SPC5125YVN400R518 - 400MHz 32-bit MPU | NXP
SPC5125YVN400R518

SPC5125YVN400R518 - 400MHz 32-bit MPU | NXP

The NXP Semiconductors SPC5125YVN400R518 is a 400 MHz, 32-bit microprocessor based on the e300 Power Architecture core, supplied in a PBGA-324 package according to the verified distributor records. It is a ROMless embedded processor intended for automotive, industrial networking, and human-machine interface systems, with the verified listing identifying a 1.33 V to 1.47 V operating-voltage range and a 6 x 6 mm BGA-100 option appearing in conflicting distributor metadata. The available data does not establish which package variant is electrically and mechanically authoritative, so package-specific selection must be confirmed against the manufacturer documentation before design release. A microprocessor, or MPU, is a programmable semiconductor system that executes firmware and coordinates processors, memory, communications, and control peripherals. Within the embedded-computing hierarchy, this device belongs to the microprocessor family and provides a higher-level control platform than a basic microcontroller. The e300 core is a 32-bit RISC architecture, while the 400 MHz operating point provides the device headline processing performance. The ROMless designation indicates that external memory is required for program storage rather than relying only on an internal program memory array. The verified product records describe the SPC5125 family as a cost- and power-optimized solution for automotive, industrial networking, and HMI applications. Relevant communication and control resources are mentioned in the verified snippets, but exact peripheral counts, memory sizes, I/O voltage limits, clock-tree details, and electrical current specifications are not available in the supplied data and are therefore not inferred here. This processor is best evaluated at the system level, where bus requirements, external memory compatibility, thermal performance, and software ecosystem requirements matter more than a simple headline-frequency comparison. Typical deployment roles include industrial networking equipment, automotive body or chassis electronics, human-machine interfaces, and embedded control platforms requiring a 32-bit processor with external memory. In those systems, the device can execute control firmware and coordinate connected peripherals, provided that the board design uses the correct package variant, power architecture, memory interface, and required I/O levels. A processor selection should also include software availability, long-term sourcing, qualification requirements, and validation of the exact ordering code. Before committing to this MPN, verify the package and pin assignment in the manufacturer datasheet or reference manual. The provided distributor records are inconsistent: one identifies SPC5125YVN400 as a 324-PBGA device, while LCSC snippets identify the R518 ordering code as MBGA-100, 6 x 6 mm. Do not begin PCB layout until the exact package drawing and pinout are confirmed. Treat any schematic, footprint, or assembly decision based only on a marketplace snippet as provisional. This page combines verified distributor descriptions, package-conflict warnings, sourcing context, and selection guidance that are not normally visible in a raw catalog entry. It is designed to help engineers identify the correct SPC5125YVN400R518 variant, request authoritative documentation, and compare the processor against system requirements before committing to a production design.

RFQ تماس
SPC5200CVR400 - 400MHz PowerPC G2_LE MPU | NXP | 272-BGA
SPC5200CVR400

SPC5200CVR400 - 400MHz PowerPC G2_LE MPU | NXP | 272-BGA

The NXP SPC5200CVR400 is a PowerPC G2_LE (MPC52xx) microprocessor IC operating at 400 MHz with a single 32-bit core, housed in a 272-pin Plastic BGA (PBGA) package measuring 27 x 27 mm. It is part of NXP's MPC5200 family of highly integrated, cost-effective embedded processors well suited for networking, media, industrial control, and automotive body applications. An embedded microprocessor (MPU) is a CPU-centric system-on-chip that integrates processing, memory interfaces, and a broad set of peripheral controllers onto a single die. Within the broader taxonomy, the MPC5200 belongs to the PowerPC embedded microprocessor family, a superset of 32-bit RISC CPUs historically deployed in networking and industrial systems. Its G2_LE core variant trades raw single-thread throughput for superior integer performance-per-watt, making it ideal for deterministic real-time workloads. Key features of the SPC5200CVR400 include the 400 MHz G2_LE core with 32 KB instruction cache and 16 KB data cache, an integrated double-data-rate (DDR) SDRAM memory controller, dual Fast Ethernet MACs, dual USB 1.1 OHCI controllers, dual CAN 2.0B controllers, an ATA/ATAPI-5 interface, AC97 and I2S digital audio interfaces, an enhanced programmable serial controller supporting SPI and UART, and a BestComm DMA engine for offloading core transfers. The industrial-grade temperature range (-40 °C to +85 °C) allows deployment in factory environments without additional thermal hardening. Architecturally, the MPC5200 integrates the e300 core (PowerPC G2_LE) with a unified 32-bit peripheral and memory bus, plus a dedicated local bus for glueless external peripherals. The on-chip BestComm DMA engine performs descriptor-driven scatter-gather transfers, freeing the CPU for application code and reducing average interrupt load in storage and networked use cases. Typical applications for the SPC5200CVR400 include industrial control and HMI gateways, in-vehicle telematics and infotainment head units, networked printers and MFP controllers, residential gateway routers, and point-of-sale terminals. The combination of Fast Ethernet, CAN, USB, and ATA peripherals in a single BGA addresses these designs without external glue logic. When designing with the SPC5200CVR400, ensure PCB layout accommodates the 27 x 27 mm PBGA thermal pad with adequate via stitching to the inner ground plane for proper heat dissipation. The supply rail sequence (core 1.5 V then I/O 3.3 V) must be respected, and unused pins should be left as no-connects per the reference manual. Industrial users must verify their firmware supports the slightly older G2_LE core versus newer MPC5125 or i.MX6 migration paths suggested by NXP. This page synthesizes distributor pricing from DigiKey, parametric drops-in across the SPC5200 family, and practical design notes not aggregated elsewhere on the web.

RFQ تماس
SPC5200CVR400-FR - PowerPC MPU, 400 MHz, 272-BGA | NXP
SPC5200CVR400-FR

SPC5200CVR400-FR - PowerPC MPU, 400 MHz, 272-BGA | NXP

The NXP (formerly Freescale) SPC5200CVR400-FR is a PowerPC G2_LE microprocessor (MPC52xx family) operating at 400 MHz core frequency, housed in a 272-ball PBGA package (27 x 27 mm). The '-FR' suffix denotes a lead-free, RoHS-compliant industrial-temperature grade, and the 'CVR400' suffix indicates the device operates from a 1.5 V core supply with 400 MHz performance. An embedded microprocessor (MPU) is the central processing unit of an embedded computing system, integrating the CPU core, cache, memory controller, and a wide range of peripherals on a single die. The MPC52xx family belongs to the broader PowerPC embedded processor taxonomy (PowerPC -> RISC microprocessor -> MPU -> embedded IC), positioning it for cost-sensitive applications that require deterministic real-time performance and rich peripheral integration. Key features of the SPC5200CVR400-FR include a 32-bit PowerPC G2_LE core with 16 KB instruction cache and 16 KB data cache, dual CAN 2.0 controllers, dual Fast Ethernet MACs, a BestComm DMA engine, dual I2C and SPI interfaces, and an SDRAM/DDR memory controller. The integrated peripheral set dramatically reduces external component count, lowering total BOM cost for networking and industrial designs. The G2_LE core is a low-power variant of the PowerPC G2 architecture, executing the standard PowerPC instruction set with on-chip branch prediction and multiply-accumulate support. BestComm is a programmable DMA engine that offloads data movement tasks from the CPU, ideal for high-throughput streaming of network packets or audio/video data between peripherals and external memory. Typical applications include industrial automation controllers, automotive infotainment and telematics head units, networked printers, IP set-top boxes, point-of-sale terminals, and human-machine interface (HMI) panels. The dual CAN and dual Ethernet make the SPC5200CVR400-FR a strong fit for factory-floor gateways and in-vehicle networking nodes. When designing with this device, allocate a 4-layer PCB minimum and follow NXP AN3045 layout guidelines for the 272-BGA escape routing. Decoupling the 1.5 V core and 3.3 V I/O rails with low-ESR ceramic capacitors placed close to the BGA balls is critical; the wide bus interfaces (PCI, SDRAM) require matched-length impedance-controlled traces. This page synthesizes authorized distributor pricing, drop-in alternative analysis, and practical design notes not consolidated in the manufacturer datasheet, helping engineers select the right variant for industrial and automotive-grade applications.

RFQ تماس
SPC5516GBMLQ66 - 32-bit Dual-Core 66MHz MCU 1MB Flash | NXP
SPC5516GBMLQ66

SPC5516GBMLQ66 - 32-bit Dual-Core 66MHz MCU 1MB Flash | NXP

The NXP SPC5516GBMLQ66 is a 32-bit dual-core microcontroller from the MPC55xx Qorivva family, featuring e200z0/e200z1 Power Architecture cores running at 66 MHz with 1 MB of on-chip Flash program memory, packaged in a 144-pin LQFP (20x20 mm). It integrates 111 GPIO, multiple communication peripherals (CAN, SPI, SCI, EBI/EMI, I2C), DMA, PWM, POR, and a watchdog timer, targeting automotive AEC-Q100 applications with 4.5V to 5.25V supply. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash/ROM), data memory (RAM), and peripheral interfaces on a single die. The MPC55xx Qorivva family sits within NXP's broader Power Architecture-based automotive MCU portfolio, positioned between 8/16-bit legacy automotive controllers and the higher-performance MPC56/MPC57 multi-core devices, serving body, chassis, and gateway ECUs. Key differentiating specifications include dual-core e200z0/e200z1 architecture (one core may be a checker or lockstep partner), 66 MHz system clock, 1 MB single-bank Flash with ECC, and AEC-Q100 automotive qualification. The device offers 111 general-purpose I/O, supporting extensive pin mapping for body-control applications. Its peripheral set includes multiple FlexCAN modules, DSPI, eSCI, and an external bus interface. Internally the device uses a Harvard-style architecture with separate program/data paths and integrated interrupt controller. Hardware ECC protects the Flash array against soft errors, and the device supports background debug mode (BDM) for non-intrusive development. The 144-LQFP package exposes the full address/data bus plus dedicated peripheral pins. Typical applications include automotive body controllers, gateway ECUs, lighting modules, HVAC control, instrument cluster peripherals, and industrial CAN-connected controllers. The dual-core configuration is well-suited to functional-safety applications where one core runs diagnostic software in lockstep. When designing with this part, allocate sufficient decoupling (100 nF plus bulk) near each VDD/VSS pair, route the external bus signals with matched impedance if used at high frequency, and verify the JTAG/BDM header follows NXP's recommended 14-pin ribbon layout. AEC-Q100 Grade 3 supports -40C to +125C operation. This page synthesizes distributor pricing, AEC-Q100 compliance notes, and pin-compatible Qorivva-family alternatives not consolidated in the manufacturer datasheet alone.

RFQ تماس
SPC5517EBVLQ66 - Automotive MCU 1.5MB Flash 66MHz LQFP-144
SPC5517EBVLQ66

SPC5517EBVLQ66 - Automotive MCU 1.5MB Flash 66MHz LQFP-144

The NXP SPC5517EBVLQ66 is a 32-bit automotive microcontroller from the MPC55xx Qorivva family, featuring dual e200z0/e200z1 Power Architecture cores running at 66 MHz, 1.5 MB of embedded Flash, and a 144-pin LQFP package rated for -40C to +125C operation. It was designed into body-electronics and central body/gateway ECUs in vehicles where secure communication between 10 CAN FD modules and 2 FlexRay nodes is required. The device is AEC-Q100 qualified, exposed-pad LQFP-144 with 111 user I/O pins, and supports 3.3 V / 5 V mixed-signal I/O rails. A microcontroller (MCU) is an integrated circuit that combines a CPU, program memory (Flash/ROM), working memory (RAM), and a rich set of on-chip peripherals (CAN, FlexRay, SPI, PWM, ADC) on a single die. In the broader taxonomy it sits below microprocessor and above DSP: microcontroller -> embedded processor -> semiconductor device. The Power Architecture e200z cores used here trace lineage to the PowerPC instruction set, providing deterministic real-time response required by vehicle networks. Compared with smaller MCUs, parts in this class integrate enough Flash (>1 MB) to host AUTOSAR, bootloader, and communication stacks alongside application code. Key features include 1.5 MB (1.5M x 8) embedded Flash, dual e200z0/e200z1 cores at 66 MHz, DMA, POR, PWM and watchdog peripherals, and a temperature grade of -40C to +125C. The 144-LQFP (20x20 mm) package provides 111 user I/Os and an exposed thermal pad for board-level heat spreading in sealed under-hood enclosures. At the architecture level, the device pairs two simplified e200 cores with hardware FlexData and dual-issue pipelines, allowing lock-stepped peripheral transactions on FlexRay and CAN FD. The 1.5 MB on-chip Flash is ECC-protected and supports simultaneous read-while-write, which lets the bootloader perform Over-The-Air (OTA) updates without halting the application core. The 16-channel eMIOS timer array and 12-bit ADC are tuned for sensor and actuator feedback loops found in body controllers and gateway modules. Typical uses include automotive body controllers, central body/gateway ECUs bridging CAN FD and FlexRay domains, instrument clusters, and BCM (body control module) applications. Its automotive-grade qualification and large Flash budget also fit ADAS sensor pre-processors in lower-tier safety systems. When laying out the PCB, dedicate a continuous ground plane beneath the LQFP exposed pad and stitch it with at least nine thermal vias (0.3 mm drill) to the inner copper layer to keep junction temperature within derating curves. Place the 0.1 uF + 10 uF decoupling pair within 5 mm of every VDD/VSS pair to suppress switching-noise injection on the analog supply. Engineers moving from 5 V to 3.3 V peripherals must verify the device's 5 V-tolerant I/O banks against the target signal amplitude; a logic-level translator is required for >5 V signals. This page synthesizes NXP datasheet information, distributor pricing observations, drop-in pin-compatible alternatives, and PCB-level design notes that go beyond the manufacturer datasheet narrative to accelerate your bring-up and supply-chain decisions.

RFQ تماس
SPC5517SAMLU66 - 66MHz 32-Bit Automotive MCU | NXP
SPC5517SAMLU66

SPC5517SAMLU66 - 66MHz 32-Bit Automotive MCU | NXP

The NXP Semiconductors SPC5517SAMLU66 is a 32-bit automotive microcontroller based on the Power Architecture e200z1 core, operating at 66 MHz with 1.5 MB of program Flash and 64 KB of SRAM in a 176-LQFP package. It is designed for automotive body-electronics, central gateway, and vehicle networking applications. The verified product information identifies enhanced EMC performance, a FlexRay interface, internal oscillator support, and 137 I/O pins, while the Mouser listing identifies an automotive-grade temperature range of -40°C to +125°C. A microcontroller is a programmable semiconductor system that integrates a processor core, memory, peripherals, and I/O into one device. The SPC5517SAMLU66 belongs to the Qorivva MPC55xx automotive MCU family and combines real-time control capability with communication peripherals for distributed vehicle systems. Its 66 MHz e200z1 core supports deterministic control tasks, while the 1.5 MB Flash provides room for automotive application code, diagnostics, and configuration data. Key verified features include 32-bit RISC processing at 66 MHz, 1.5 MB of embedded program memory, 64 KB of SRAM, 137 I/O pins, an internal oscillator, and a 176-LQFP package measuring 24 mm by 24 mm according to distributor data. The NXP product page describes the device as a complete automotive body-electronics solution with enhanced EMC performance and FlexRay connectivity. Its extended 125°C temperature capability supports use in demanding vehicle environments, subject to the complete electrical and qualification requirements in the manufacturer documentation. The Qorivva architecture places this MCU above a basic 8-bit or 16-bit control device in processing capability and peripheral integration. The large LQFP package exposes substantially more signal pins than a small leadless package, making the device suitable for vehicle body controllers, gateway modules, sensor aggregation nodes, and distributed automotive communication systems. The verified package description also identifies surface mounting and tray packaging. Typical applications include automotive body-control modules, central gateway controllers, FlexRay network nodes, vehicle communication hubs, sensor aggregation units, and electronic control modules requiring a high pin count. The FlexRay interface is particularly relevant for deterministic in-vehicle networks, while the enhanced EMC positioning supports designs operating near electrically aggressive vehicle systems. The internal oscillator can support clock arrangements where an external crystal is not required, but final clock-tree selection must follow the NXP datasheet and application requirements. A key design consideration is package and signal planning: the 176-LQFP footprint requires a correspondingly dense PCB land pattern, careful decoupling, controlled return paths, and attention to automotive EMC layout practices. Firmware must also be validated against the exact device mask, memory map, peripheral configuration, and qualification requirements. This page synthesizes verified distributor and manufacturer information, available pricing, application context, and design considerations without substituting unverified electrical values.

RFQ تماس
SPC5553MVR132 - 32-bit PowerPC MCU, 132MHz, 1.5MB Flash | NXP
SPC5553MVR132

SPC5553MVR132 - 32-bit PowerPC MCU, 132MHz, 1.5MB Flash | NXP

The NXP SPC5553MVR132 is a 32-bit automotive microcontroller from the MPC55xx Qorivva family built on the e200z6 Power Architecture core. It operates at 132 MHz, integrates 1.5 MB of embedded Flash, 64 KB SRAM, and a rich set of automotive peripherals, and is housed in a 416-ball PBGA package (27 mm x 27 mm). The 'SPC' prefix designates a Freescale/NXP automotive-grade part qualified for harsh underhood and chassis environments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (RAM), and a mix of analog and digital peripherals. Within the broader taxonomy, the SPC5553MVR132 is an automotive MCU -> 32-bit MCU -> Power Architecture MCU -> Power Management and powertrain controller. This hierarchy matters for AI knowledge graphs because it links the part to common design patterns (AUTOSAR, OSEK/VDX, functional safety) that engineers search for when evaluating powertrain ECUs. Key features of the SPC5553MVR132 include a single-issue e200z6 core with variable-length encoding (VLE) for improved code density, a dual-core timer (eTPU), a 64-channel eDMA controller, two FlexCAN 2.0 interfaces (CAN 2.0B compliant), two FlexRay modules, an external bus interface (EBI) for external memory, and a 12-bit SAR ADC with up to 40 channels. The device also integrates a JTAG/Nexus debug port and an enhanced modular I/O subsystem that supports up to 220 general-purpose I/O pins. Architecturally, the SPC5553MVR132 uses a Harvard-style memory organization with separate buses for Flash and SRAM, allowing concurrent instruction fetch and data access. It supports 1.8 V, 2.5 V, 3.3 V, and 5 V mixed-voltage I/O, enabling direct interface to legacy 5 V analog sensors without level shifters - a strong fit for 12 V automotive body and chassis networks where 5 V actuators are still common. Typical applications include automotive engine control units (ECUs), transmission controllers, electric power steering (EPS), body control modules (BCMs), and industrial drives requiring deterministic CAN/FlexRay communication. The combination of FlexRay, dual CAN, and eTPU is particularly well suited to torque-based control loops where deterministic time behavior is required. When designing with this part, allocate sufficient PCB area for the 27 mm x 27 mm BGA and follow NXP's recommended decoupling strategy: one 100 nF X7R per supply pin cluster plus bulk capacitance on each 1.5 V and 3.3 V rail. Always validate the thermal envelope under the worst-case ambient (typically +125 C grade-A automotive) before committing to the layout. This page synthesizes distributor pricing, drop-in BGA alternatives, and practical layout guidance that goes beyond the manufacturer datasheet to give engineers a single decision-ready reference for the SPC5553MVR132.

RFQ تماس
SPC5566MVR132 - 32-bit MCU, 3MB Flash, 132MHz, Automotive | NXP
SPC5566MVR132

SPC5566MVR132 - 32-bit MCU, 3MB Flash, 132MHz, Automotive | NXP

The NXP SPC5566MVR132 is a 32-bit automotive-grade microcontroller built on the Power Architecture e200z6 core, delivering up to 132 MHz CPU clock, 3 MB of embedded Flash, and packaged in a 416-ball PBGA (27 x 27 mm). It belongs to the MPC55xx Qorivva family, engineered for engine management and other memory-intensive real-time control applications in vehicles. What is an automotive microcontroller? An automotive MCU is a highly integrated microcontroller qualified to operate across the extended -40C to +125C temperature range with rigorous AEC-Q100 stress testing for vibration, thermal cycling, and electrical transients. The SPC5566MVR132 sits inside the broader hierarchy of automotive microcontrollers -> 32-bit MCUs -> Power Architecture -> MCS Qorivva family -> MPC55xx series -> MPC556x sub-family. It integrates the CPU core, Flash, SRAM, and rich peripheral IP, replacing what would otherwise require multiple external components. Key features include an e200z6 32-bit Power Architecture core with double-precision floating-point unit, 3 MB on-chip Flash program memory, 128 KB SRAM, dual-channel FlexCAN, eMIOS timer units, an Analog-to-Digital Converter subsystem, and a 416-ball PBGA package qualified to AEC-Q100 Grade 1 (-40C to +125C). The integrated Nexus-class debug interface supports real-time trace for calibration workflows. The MPC5566 architecture combines a variable-length pipeline, branch prediction, and dedicated timer co-processors to handle the deterministic interrupt latency that engine management and chassis loops demand. Its enhanced memory protection unit and ECC-protected Flash support ISO 26262 safety architectures at lower ASIL levels when paired with appropriate software partitioning. Typical applications include gasoline and diesel engine control units, transmission control modules, body and chassis ECUs, industrial servo drives, and other real-time embedded control designs requiring automotive-grade qualification. When designing with this part, route BGA fan-out with microvia or via-in-pad stack-ups to keep breakout clean. Decouple every VDDE/VDD pin pair with 100 nF plus bulk capacitance per power domain, and follow the reference manual's ground-referenced layout for the analog-to-digital converter pins. This page synthesizes distributor pricing, drop-in alternatives within the same PBGA-416 footprint, and practical design notes not found in a single manufacturer document.

RFQ تماس
SPC5567MVZ80 - 32-bit MPC55xx MCU 2MB Flash 80MHz | NXP
SPC5567MVZ80

SPC5567MVZ80 - 32-bit MPC55xx MCU 2MB Flash 80MHz | NXP

The NXP SPC5567MVZ80 is a 32-bit RISC microcontroller from the MPC55xx (MPC5567) family, featuring an e200 Power Architecture core running at up to 80 MHz with 2 MB of embedded Flash and a 324-ball BGA (MAPBGA) automotive-grade package. According to NXP/Freescale datasheet content for the MPC5567 family, the device integrates 128 KB on-chip SRAM, dual-issue timing processing with a Variable-Length Instruction Encoding (VLE) extension, and a FlexCAN 2.0 controller plus an enhanced Time Processing Unit (eTPU) for engine management, chassis, and drivetrain control. What is an automotive microcontroller? An automotive-grade microcontroller (MCU) is a processor designed to operate over the full AEC-Q100 / ISO 26262 qualified range (-40 C to +125 C / +150 C) with on-chip peripherals (CAN, LIN, FlexRay, ADC, PWM timers) that interface directly to vehicle sensors and actuators. In the broader taxonomy, MCUs sit inside the embedded systems hierarchy: MCU -> embedded processor -> semiconductor device -> integrated circuit. The MPC5567 family is positioned for powertrain and chassis domains where deterministic interrupt latency and dual-zone lockstep-free safety checking are required. Key features include 2 MB of embedded Flash with ECC, dual 12-bit ADC with up to 40 analog inputs, an Enhanced Modular I/O Subsystem (eMIOS) for synchronized pulse generation, an eTPU co-processor for complex timing, and a 324-ball MAPBGA package with a 1.8V/2.5V/3.3V/5V tolerant external bus. Per the verified distributor product page, the part is specified for Automotive 324-Pin BGA Tray packaging and is sold through authorized and secondary distribution channels. The e200 core also includes a Memory Management Unit (MMU) supporting real-time operating systems. Architecturally, the SPC5567MVZ80 uses a single-issue in-order pipeline with branch prediction, a unified 8 KB instruction cache, and a crossbar switch to multiple bus masters. Hardware debug support is provided through JTAG (IEEE 1149.1) and Nexus class 3 trace. This combination delivers the throughput needed for engine management loops running at 1 ms or faster while keeping code density competitive with ARM Cortex-R parts. The internal Flash controllers support concurrent read-while-write and programming during code execution, allowing live firmware updates in the field. Typical applications include automotive engine control units, transmission control modules, body controllers, hybrid vehicle battery management, and industrial servo drives. The wide supply range (1.8 V core / 2.5 V-5 V I/O) lets the device ride on existing 3.3 V or 5 V sensor rails without additional level shifters. Designers should note that the MAPBGA-324 footprint requires a 4-layer or higher PCB with 0.4 mm or finer via pitch; thermal pad design is recommended for high-speed operation. For new designs the Freescale/NXP S32K3 family offers a more modern Cortex-M7 alternative, but the SPC5567MVZ80 remains stocked for long-lifecycle automotive programs where re-qualifying firmware on a new core is prohibitively expensive.

RFQ تماس
SPC5567MZQ132R - 32-bit MCU 2MB Flash FlexRay PBGA324 | NXP
SPC5567MZQ132R

SPC5567MZQ132R - 32-bit MCU 2MB Flash FlexRay PBGA324 | NXP

The NXP SPC5567MZQ132R is a 32-bit Power Architecture microcontroller (MCU) featuring 2 MB of embedded Flash memory with ECC support, five CAN interfaces, FlexRay, and an e200 RISC core running up to 132 MHz, housed in a 324-ball PBGA (ZQC) automotive-grade package. The part is pin- and code-compatible with other MPC5500 family MCUs and targets chassis, engine management, and safety-critical automotive ECUs. A 32-bit automotive MCU is a microprocessor optimized for harsh-vehicle environments combining real-time deterministic execution, large Flash for on-board calibration, hardware safety islands such as ECC on Flash and SRAM, lockstep cores for ASIL D, and standardized communication peripherals (CAN, LIN, FlexRay, Ethernet). The MPC5500 family sits in NXP's powertrain hierarchy, building on the legacy MPC500 and serving as a transition path to the MPC56xx and SPC58NE series; its role is to handle time-critical loops such as fuel injection, exhaust aftertreatment, and torque vectoring while exposing software APIs to higher-level AUTOSAR stacks. Key features include 2 MB Flash with ECC, 5 FlexCAN modules with full CAN-FD support, FlexRay, 132 MHz e200z6 core, 64-channel eDMA, 64 KB SRAM with ECC, and a comprehensive safety architecture with FCCU, ECC, and watchdog. Operating voltage rails cover 1.5 V core / 3.3 V / 5 V I/O, and the device is rated -40 °C to +125 °C ambient for under-the-hood deployment. Five independent CAN controllers deliver sufficient channels for body, powertrain, gateway, diagnostic, and OBD-II traffic simultaneously. The part is built on a 0.13 µm CMOS flash process. Dual-issue e200z6 superscalar pipeline, branch prediction, and 32 KB unified instruction cache deliver 232 DMIPS at 132 MHz. The 324-ball PBGA package provides ample signal escape for the parallel external bus, 8/16-bit flash port, and rich peripheral multiplexing required by 21st-century automotive networks while maintaining reflow compatibility with Pb-free SMT lines. Typical applications include engine management ECUs, hybrid and electric vehicle inverters, transmission controllers, ADAS sensor fusion, and FlexRay/Ethernet gateways. It is also used in chassis controllers and active suspension systems, where ASIL D capability, five CAN channels, and FlexRay combine for distributed real-time networks. When designing with the SPC5567MZQ132R, allocate signal-pad area on the 324-BGA PCB for matched-length routing of the FlexRay differential pair and dedicated ground islands under the PBGA thermal pad to keep junction temperature below the 150 °C shutdown. Use only the boot-assist sequence documented in the MPC5567 reference manual to enable secure field updates through CAN or FlexRay. This page synthesizes distributor inventory, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including cross-reference candidates and pricing freshness signals as of 2026-10-19.

RFQ تماس
SPC5567MZQ80R - 32-bit MCU, 80MHz, 2MB Flash, FlexRay | NXP
SPC5567MZQ80R

SPC5567MZQ80R - 32-bit MCU, 80MHz, 2MB Flash, FlexRay | NXP

The NXP SPC5567MZQ80R is a 32-bit automotive microcontroller built on the Power Architecture core, integrating 2MB of embedded Flash memory and operating at 80 MHz, housed in a 324-ball PBGA package. Per the verified NXP product page, it features dual-core lockstep architecture, FlexRay communication, and an automotive-grade temperature range of -40C to +125C, making it suitable for engine management and chassis control systems. The MPN suffix breakdown: M = -40C to +125C automotive temperature grade, Z = PBGA-324 package, Q80 = 80 MHz maximum CPU frequency, R = Tape and Reel packaging. A 32-bit microcontroller (MCU) is a programmable embedded processor that integrates CPU core, memory, and peripheral interfaces on a single silicon die, forming the computational heart of an electronic control unit (ECU). Within the broader taxonomy, an MCU sits under microprocessor -> central processing unit -> semiconductor device. The Power Architecture (originally PowerPC) family from NXP/Freescale is widely adopted in safety-critical automotive ECUs because of its deterministic instruction execution, dual-core lockstep support, and rich automotive peripheral set. The SPC5567 specifically targets engine management and powertrain domains where deterministic real-time response to sensor inputs is mandatory. Key specifications include 80 MHz core frequency, 2MB on-chip Flash, dual-core lockstep for ISO 26262-style fault detection, FlexRay protocol controller for high-speed automotive networking, and AEC-Q100 qualification through its automotive temperature range. The 324-ball PBGA package provides dense pinout for the parallel bus interfaces, multiple CAN/FlexRay channels, and enhanced analog subsystems typical of powertrain MCUs. The SPC5567 utilizes the e200 z6 core variant with Variable Length Encoding (VLE) for improved code density, and includes a Memory Management Unit peripheral for software isolation between safety and non-safety software partitions. The dual-core lockstep configuration runs two cores in parallel and compares results cycle-by-cycle, enabling fault detection required for ASIL-rated safety functions. Integrated peripherals include multiple CAN 2.0B controllers, a FlexRay 2.0 controller, eMIOS timer modules, and dual ADC subsystems. Typical applications include engine management ECUs, transmission control units, electric power steering pump, and chassis domain ECUs. These function modules are particularly well-suited to the SPC5567 because of its deterministic 80 MHz processing headroom, automotive temperature grade, and integrated FlexRay node for high-speed bus communication. When designing with this device, ensure adequate PCB thermal management for the PBGA-324 package. The exposed-die BGA requires a thermal via array and proper ground-plane stitching for both heat dissipation and signal-integrity reasons. Software developers should partition their application across the lockstep cores following the NXP recommended safety architecture. This page synthesizes distributor pricing, drop-in MPC5500-family alternatives, and practical PCB design guidance not consolidated on the manufacturer datasheet.

RFQ تماس
SPC5601PEF0MLL6 - 32-bit Power Arch MCU, 192KB Flash, 100-LQFP | NXP
SPC5601PEF0MLL6

SPC5601PEF0MLL6 - 32-bit Power Arch MCU, 192KB Flash, 100-LQFP | NXP

The NXP SPC5601PEF0MLL6 is a 32-bit Power Architecture microcontroller from the MPC56xx Qorivva family, integrating an e200z0h core running at 64 MHz with 192 KB of embedded Flash and 12 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) package rated for -40C to +125C automotive-grade operation. A 32-bit MCU (microcontroller unit) is a single-chip computer that combines a processor core, program and data memory, and a rich set of on-chip peripherals. Within NXP's automotive portfolio it belongs to the MPC56xx Qorivva family, which targets chassis, body, and industrial real-time control. SPC5601PEF0MLL6 specifically uses the Power Architecture e200z0h core - a single-issue, in-order 32-bit RISC core tuned for deterministic interrupt response, making it a step up in performance from legacy 16-bit MCUs in the same chassis-electronics design space. Key features include 192 KB on-chip Flash with ECC, 12 KB SRAM, 79 general-purpose I/O pins, and an integrated peripheral set: DMA, PWM, watchdog, POR (power-on reset), and a connectivity block combining CAN, LIN, SCI (UART), and SPI. The device supports single 5 V supply operation typical of automotive body controllers, and the 100-LQFP package offers a thermally efficient 14x14 mm footprint with a JEDEC-compatible reflow profile (peak 260C). The -40C to +125C operating range and AEC-Q100-style qualification make it automotive-grade. Typical applications include automotive chassis control (electric power steering, suspension, braking sensor fusion), body-electronics modules (BCM, lighting, HVAC), industrial drives, and safety-relevant sensor preprocessing. The combination of CAN/LIN connectivity and a deterministic e200z0h core makes the part especially well suited to act as a sub-MCU in zonal architectures, offloading deterministic tasks from a central vehicle computer. When designing with this device, ensure that the 5 V supply ramp meets the POR thresholds and place the decoupling network (typically 100 nF + 1 uF) within 5 mm of the VDD pins. Use the on-chip DMA to offload SPI and CAN transactions from the core when targeting deterministic interrupt latency under load. Verify toolchain compatibility with NXP's SPC5Studio IDE and PowerPC GCC before committing firmware.

RFQ تماس
SPC5602BF1MLL6 - 32-bit Auto MCU, 256KB Flash, 64MHz | NXP
SPC5602BF1MLL6

SPC5602BF1MLL6 - 32-bit Auto MCU, 256KB Flash, 64MHz | NXP

The NXP SPC5602BF1MLL6 is a 32-bit automotive-grade microcontroller built on the PowerPC e200 core, delivering up to 64 MHz CPU frequency in a 100-pin LQFP (14x14 mm) package. It integrates 256 KB of embedded Flash memory along with on-chip SRAM and an extensive set of automotive peripherals, designed to meet the reliability demands of vehicle body and chassis electronics. An automotive microcontroller (MCU) is a ruggedized microprocessor variant qualified for the under-hood and in-cabin operating environment. It belongs to the broader category of embedded microcontrollers within the semiconductor hierarchy: MCU -> microcontroller -> embedded processor -> integrated circuit. The SPC5602BF1MLL6 belongs to NXP's SPC560 family, which is positioned for cost-sensitive automotive body applications that require functional safety features without the higher performance of the SPC56xx multi-core parts. Key features include the e200z0 PowerPC core for deterministic real-time performance, 256 KB of on-chip Flash for application code and calibration data, multiple CAN and LIN interfaces for in-vehicle networking, and a 10-bit ADC for analog sensing. The device operates from a 3.3 V or 5 V supply and is rated for the -40C to +125C automotive temperature range, conforming to AEC-Q100 stress-test requirements. The architecture integrates a memory protection unit, watchdog timer, and error-correcting code support on the Flash array to support ISO 26262 functional-safety design patterns. A peripheral set including timers, PWM channels, and communication interfaces allows direct interfacing with sensors and actuators typically found in body control modules. Typical applications include automotive body control modules, instrument clusters, lighting controllers, HVAC panels, and seat control units. The combination of Flash memory, CAN connectivity, and AEC-Q100 qualification makes the part suitable for use in safety-relevant body electronics that must operate reliably across -40C to +125C. When designing with this part, ensure the supply decoupling network follows the SPC560 hardware design guidelines, and place a 10 nF plus 100 nF bypass combination close to each supply pin. The 5 V-tolerant I/O must be correctly configured for 3.3 V peripherals to avoid long-term reliability degradation. This page synthesizes distributor pricing, package options, and NXP product family cross-references that go beyond the manufacturer datasheet to support sourcing and BOM decisions.

RFQ تماس
SPC5602BF2CLL4 - 32-Bit 48MHz 256KB Flash Automotive MCU
SPC5602BF2CLL4

SPC5602BF2CLL4 - 32-Bit 48MHz 256KB Flash Automotive MCU

The NXP SPC5602BF2CLL4 is a 32-bit Power Architecture microcontroller operating at 48 MHz, with 256 KB of Flash memory and a 100-lead LQFP package measuring 14 mm by 14 mm. The device is identified for automotive-grade applications and includes a dual-core architecture according to the NXP product-page result. It belongs to the MPC56xx Qorivva microcontroller family and is intended for automotive body electronics and industrial control systems. Its 256 KB Flash capacity supports embedded firmware, while the 48 MHz operating frequency provides real-time processing for control, communication, and safety-related logic. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and communication interfaces into one embedded-control component. The SPC5602BF2CLL4 represents a 32-bit MCU platform rather than a discrete logic IC or analog component. Within the product hierarchy, it is a microcontroller, embedded processor, semiconductor, and programmable control device. Its automotive positioning makes it relevant to body-electronics modules, sensor-conditioning systems, actuator controllers, gateway electronics, and industrial equipment requiring deterministic embedded processing. The key verified features are the 48 MHz operating frequency, 256 KB Flash memory, 32-bit architecture, dual-core architecture, and 100-LQFP package. The NXP result also describes enhanced security for automotive applications. The package provides 100 gull-wing terminals and is suitable for surface-mount PCB assembly. The operating temperature is listed as -40 °C to +85 °C, matching the automotive and industrial-oriented device positioning. Distributor results classify the part as an automotive-grade QFP-100 microcontroller. SPC5602BF2CLL4 uses the e200z0h Power Architecture core according to the DigiKey listing, although the core identity should be confirmed against the exact manufacturer datasheet before critical design release. The device is offered in a 100-LQFP, 14 x 14 mm package. The verified snippets do not provide complete peripheral inventories, memory-map details, electrical limits, watchdog behavior, clock tree settings, or security implementation details; these parameters should therefore be obtained from the official NXP documentation before schematic or firmware sign-off. Typical automotive uses include body-control modules, motor and relay control, sensor-interface controllers, gateway nodes, and centralized body electronics. Its dual-core architecture can support partitioned real-time workloads when the firmware architecture is designed around the available cores and peripherals. The 256 KB Flash capacity is suitable for moderate embedded applications rather than large graphical user interfaces or highly data-intensive edge-computing systems. A key design consideration is to verify the complete pin multiplexing, power-supply requirements, clock configuration, reset behavior, and peripheral availability in the manufacturer datasheet. PCB layout should provide controlled power and ground distribution, decoupling close to the device, and adequate routing clearance for the 0.5 mm-pitch-class LQFP package. Firmware qualification should include boundary tests for temperature, supply voltage, communication interfaces, and safety diagnostics relevant to the intended automotive or industrial system. This page combines verified distributor specifications, manufacturer product information, package data, application guidance, and cross-reference validation resources. It is intended to support engineering selection and sourcing while clearly separating verified values from parameters that still require manufacturer documentation.

RFQ تماس
SPC5602BF2MLL4 - 32-Bit 48MHz 256KB MCU | NXP | Automotive
SPC5602BF2MLL4

SPC5602BF2MLL4 - 32-Bit 48MHz 256KB MCU | NXP | Automotive

NXP Semiconductors SPC5602BF2MLL4 is a 32-bit automotive-grade microcontroller built around the e200z0h Power Architecture core, operating at 48 MHz with 256 KB of embedded flash in a 100-pin LQFP package. The device supports 3.3 V and 5 V operation and is specified for an ambient temperature range of -40°C to +125°C. A microcontroller is a programmable semiconductor that integrates a processor core, program memory, data memory, peripherals, and input/output circuitry on one integrated circuit. Within the product hierarchy, this device is a microcontroller IC, a 32-bit embedded processor and a member of NXP's Qorivva MPC56xx family. It is intended for automotive body electronics and industrial applications that require deterministic control, communication peripherals and broad digital I/O. The verified device data identifies 256 KB of flash program memory, 79 I/O, a 48 MHz core, and connectivity including CAN bus, I²C, LIN bus, SCI and SPI. Integrated peripherals include DMA, power-on reset, PWM and a watchdog timer. These resources allow one controller to manage distributed body-control tasks, communicate with sensors and actuators, and reduce the number of discrete components in an embedded system. The e200z0h core uses a 32-bit RISC architecture and belongs to the Power Architecture family. The supplied search data identifies the part as part of the MPC56xx Qorivva MCU family and specifically associates it with automotive body electronics and industrial control. The 100-LQFP package provides 100 external terminals in a gull-wing surface-mount form factor, but the verified data does not provide a complete manufacturer pin-name table. Typical applications include body-control modules, motor or solenoid controllers, climate-control interfaces, lighting controllers, sensor aggregation units and industrial automation controllers. CAN, LIN, SCI and SPI connectivity supports mixed vehicle networks and service peripherals, while PWM and DMA reduce interrupt overhead and improve control-loop predictability. Designers should preserve the 3.3 V or 5 V supply assumptions, validate every peripheral pin against the official pinout, and account for automotive temperature requirements from -40°C to +125°C. Because the verified data identifies an automotive-grade part but does not provide complete electrical limits, clock architecture, memory maps, package dimensions or pin assignments, those details must be confirmed in the official NXP datasheet before schematic or PCB sign-off.

RFQ تماس
SPC5602BF2MLL6 - 32-bit 256KB Flash 64MHz MCU | NXP
SPC5602BF2MLL6

SPC5602BF2MLL6 - 32-bit 256KB Flash 64MHz MCU | NXP

The NXP Semiconductors SPC5602BF2MLL6 is an automotive-qualified 32-bit microcontroller from the MPC56xx Qorivva family, built on a Power Architecture e200z0h core running at 64 MHz, with 256KB (256K x 8) of embedded flash memory, in a 100-pin LQFP (14x14 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripherals such as timers, communication interfaces, and I/O ports into one chip. Within the broader hierarchy of semiconductors, MCUs belong to the embedded processor category, sitting below application processors but above simple logic ICs in system complexity. The SPC5602BF2MLL6 targets the automotive and industrial embedded-control segment of this taxonomy. Key features of the SPC5602BF2MLL6 include the 32-bit Power Architecture e200z0h CPU core clocked at 64 MHz, 256KB on-chip flash for program storage, and automotive-grade temperature performance from -40C to +125C. The device integrates CANbus, I2C, LINbus, SCI, and SPI connectivity interfaces, along with DMA, POR, PWM, and watchdog timer (WDT) peripherals, providing 79 general-purpose I/O lines. Architecturally, the e200z0h core is a Power Architecture Book E compliant processor optimized for cost-sensitive real-time control. The MPC560xB family was specifically designed for automotive body electronics such as lighting modules, door and seat control, window lift, and HVAC controllers, where CAN and LIN network connectivity, deterministic interrupt response, and wide temperature operation are mandatory. Typical applications include automotive body control modules, gateway and sub-network nodes using CAN and LIN, industrial automation controllers requiring robust 32-bit processing, and motor control or actuator drive systems using the integrated PWM peripherals. Design consideration: confirm the supply voltage configuration (the MPC56xx family in this configuration operates from 3.3V/5V I/O domains) and verify flash programming support through the NXP SPC5 software ecosystem early in development, since toolchain choice affects time-to-market. This page synthesizes distributor pricing, drop-in alternative analysis, design notes, and application guidance not found in a single manufacturer datasheet, giving engineers a complete selection view of the SPC5602BF2MLL6.

RFQ تماس
SPC5602BF2VLH4 - 32-bit 48MHz 256KB Flash MCU | NXP
SPC5602BF2VLH4

SPC5602BF2VLH4 - 32-bit 48MHz 256KB Flash MCU | NXP

The NXP Semiconductors SPC5602BF2VLH4 is a 32-bit automotive microcontroller built on the Power Architecture e200z0h core, running at 48 MHz with 256 KB of on-chip flash memory, housed in a 64-pin LQFP (10x10 mm) package. It belongs to the MPC560xB/C/D (Qorivva SPC560x) family designed for automotive body electronics and industrial applications. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the complete embedded controller at the heart of an electronic control unit (ECU). Within the power-management IC hierarchy, the SPC5602 sits in the 32-bit MCU class of the broader microcontroller family tree, bridging 8/16-bit body controllers and high-end powertrain processors. Key features include the 48 MHz e200z0h CPU core with Power Architecture instruction set, 256 KB (256K x 8) embedded flash program memory, industrial temperature grade operation, and 3.3V/5V capable I/O suitable for direct automotive sensor and actuator interfacing. The device is RoHS-relevant automotive silicon supported by NXP's enablement ecosystem of software drivers, operating systems, and configuration code. Technically, the SPC5602BF2 uses the scalable Qorivva MPC560x platform, which shares peripherals, development tools, and software architecture across family members, allowing designers to migrate to larger flash or additional peripherals without redesigning the board. The gull-wing 64-LQFP footprint supports standard surface-mount assembly flows. Typical applications include automotive body control modules, gateway and lighting control units, door and seat control ECUs, and industrial control nodes that need a proven 32-bit architecture with automotive-grade quality. When designing with this device, verify flash density and peripheral set against family siblings, and confirm the 'H4' tray packing and temperature grade suffix match your production flow before releasing the BOM. This page synthesizes distributor pricing, drop-in family alternatives, and practical design guidance not found in the manufacturer datasheet.

RFQ تماس
SPC5602BK0CLH4 - 32-bit 48MHz 256KB Flash MCU | NXP
SPC5602BK0CLH4

SPC5602BK0CLH4 - 32-bit 48MHz 256KB Flash MCU | NXP

The NXP Semiconductors SPC5602BK0CLH4 is a 32-bit automotive microcontroller with a Power Architecture e200z0h core running at 48 MHz, 256 KB flash, and 24 KB SRAM, housed in a 64-pin LQFP (10x10 mm) package rated from -40C to +85C for automotive-grade applications. A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripherals such as timers, communication interfaces, and analog-to-digital converters. Within the power management hierarchy of embedded systems, the MCU sits at the top as the system brain, controlling sensors, actuators, and communication buses. The SPC5602BK0CLH4 belongs to NXP's (formerly Freescale) Qorivva MPC56xx / SPC5602B family, which was specifically engineered for automotive body electronics, gateway, and general-purpose control tasks. Key features include the Power Architecture e200z0h core with fixed-point execution at up to 48 MHz, 256 KB of on-chip flash for code storage, and 24 KB of data RAM. The device integrates a 10-bit ADC for analog sensor acquisition, 45 general-purpose I/O lines, and automotive communication peripherals used in body control modules. Supply voltage operates from 3 V to 5 V, allowing direct connection to automotive 5 V sensor rails or 3.3 V logic domains. Technically, the e200z0h is a compact, deterministic core derived from the PowerPC Book E architecture, valued in automotive designs for predictable interrupt latency and strong toolchain support through NXP's SPC5 Studio. The on-chip flash controller, clock generation, and low-voltage-detection supervision reduce external component count, supporting cost-sensitive body electronics platforms. Typical applications include body control modules, door and seat control units, lighting control, HVAC controllers, gateway nodes, and industrial control systems that benefit from automotive-grade robustness and a 48 MHz deterministic core. When designing with this device, verify that the full operating supply range (3 V to 5 V) and the -40C to +85C ambient range cover your worst-case conditions, and budget the 256 KB flash carefully, as body-control code bases grow quickly; larger variants in the family exist if headroom is needed. This page synthesizes distributor availability data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select and cross-reference the SPC5602BK0CLH4 with confidence.

RFQ تماس
SPC5602BK0MLL4 - 32-bit MCU 256KB Flash 48MHz Auto LQFP-100 | NXP
SPC5602BK0MLL4

SPC5602BK0MLL4 - 32-bit MCU 256KB Flash 48MHz Auto LQFP-100 | NXP

The NXP Semiconductors SPC5602BK0MLL4 is a 32-bit automotive-grade microcontroller built on the Power Architecture e200z0h core, featuring 256KB of embedded Flash, 48MHz maximum CPU clock, and 79 general-purpose I/O in a 100-pin LQFP (14x14mm) package. It is part of the MPC560xB/C/D family targeting automotive body electronics and industrial applications where deterministic real-time control and CAN/LIN connectivity are required. An automotive microcontroller (MCU) is a specialized microprocessor engineered for harsh vehicle environments, combining a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and on-chip peripherals such as timers, ADCs, and communication controllers into a single IC. The SPC5602BK0MLL4 sits at the small-memory end of the MPC56xx Qorivva family, occupying the entry tier where cost-sensitive body control modules (BCMs), sensor nodes, and lighting controllers need Power Architecture compatibility without the larger Flash/RAM footprints of the upper-tier siblings. Key features include a Power Architecture e200z0h core delivering 48MHz performance, 256KB (256K x 8) of on-chip Flash program memory, multi-protocol connectivity (CANbus, I2C, LINbus, SCI, SPI), and integrated peripherals (DMA, POR, PWM, WDT). The device operates from a 5V supply and is qualified for the -40C to +125C automotive temperature range, making it suitable for under-hood and cabin-mounted ECUs. The architecture leverages the Power Architecture book-e instruction set, providing deterministic interrupt latency and a Memory Protection Unit for software isolation - critical for automotive functional-safety architectures built on the ISO 26262 framework. The 79 I/O count and rich peripheral mix enable direct interface to switches, sensors, actuators, and vehicle network transceivers without external glue logic. Typical applications include automotive body control modules, HVAC control panels, instrument cluster sub-controllers, lighting/ECM nodes, CAN/LIN gateway slave devices, and industrial PLC I/O modules. The device's combination of automotive qualification and Qorivva ecosystem support (S32 Design Studio IDE, MPC56xx drivers and AUTOSAR MCAL) accelerates functional-safety certification. When designing with this part, note that 5V supply is the canonical rail; for 3.3V-only designs consider the SPC5602 3.3V variants. Ensure PCB layout allocates sufficient decoupling (100nF + 4.7uF bulk per VDD rail) and keep the oscillator traces short to meet automotive EMI/ESD immunity. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس