محصولات (44,000+)

INA101CM - 25uV Instrumentation Amplifier | Texas Instruments
INA101CM

INA101CM - 25uV Instrumentation Amplifier | Texas Instruments

Texas Instruments INA101CM is a very-high-accuracy instrumentation amplifier for low-level differential signal amplification and general-purpose data acquisition. Its headline specifications include 25 uV maximum offset voltage, 0.25 uV/°C maximum drift, 13 nV/√Hz input noise, and a 106 dB common-mode rejection ratio at 60 Hz. The device is offered in the INA101CM configuration in a 10-pin TO-100 metal package. An instrumentation amplifier is a specialized analog amplifier optimized for measuring small signals embedded in larger common-mode voltages. It typically combines three precision operational amplifiers with laser-trimmed metal-film resistors to provide high differential input impedance, accurate gain, and strong rejection of common-mode interference. Within the analog IC hierarchy, an instrumentation amplifier is a precision amplifier used for sensor conditioning, data acquisition, and industrial measurement systems. The INA101CM combines three precision operational amplifiers and laser-trimmed metal-film resistors on one monolithic integrated circuit. Its maximum input offset voltage is 25 uV, while maximum input drift is 0.25 uV/°C. Low nonlinearity of 0.002% supports predictable signal transfer, and the 13 nV/√Hz noise specification makes the amplifier suitable for low-level bridge, thermocouple, and resistance-temperature-detector signals. A common-mode rejection ratio of 106 dB at 60 Hz helps suppress mains-related interference and other signals shared equally by both inputs. The differential input resistance is approximately 10 GΩ, reducing loading on high-impedance sources. The listed operating supply range is ±5 V to ±20 V, and the typical slew rate is 0.4 V/µs. Listed bandwidth figures range from 25 kHz to 300 kHz across source descriptions, so the manufacturer datasheet should be consulted for gain-specific bandwidth limits. Typical uses include strain-gauge bridge conditioning, thermocouple and RTD signal acquisition, industrial process measurement, medical instrumentation, and remote sensor interfaces. The device is particularly useful when a millivolt-level differential signal must be amplified while rejecting substantial common-mode voltage present in industrial wiring environments. When designing around the INA101CM, verify the gain-set resistor values against the manufacturer gain equation and check bandwidth at the selected gain. Keep input and reference-pin traces short, use a low-noise reference when gain adjustment is required, and provide stable bypass capacitance close to the supply pins. The 10-pin TO-100 package also requires adequate lead clearance and appropriate thermal consideration at elevated ambient temperatures. This product page combines the manufacturer electrical characteristics, package information, replacement guidance, application fit, and design considerations to support faster engineering evaluation. The INA101CM datasheet remains the controlling document for pin assignments, gain curves, absolute maximum ratings, and orderable option details.

RFQ تماس
INA101HP - Very High Accuracy Instrumentation Amp | TI
INA101HP

INA101HP - Very High Accuracy Instrumentation Amp | TI

The Texas Instruments INA101HP is a very high accuracy instrumentation amplifier delivering 25 uV maximum offset voltage, 0.25 uV/C maximum offset drift, and 0.002% maximum nonlinearity, housed in a 14-pin plastic PDIP (N) package operating from dual supplies of +/-5 V to +/-20 V. An instrumentation amplifier is a specialized closed-loop differential amplifier designed to amplify low-level sensor signals while rejecting common-mode noise. Unlike a standard op amp, an instrumentation amplifier provides a precise gain set by a single external resistor, extremely high input impedance on both inputs, and a high common-mode rejection ratio (CMRR) without requiring tightly matched external resistor networks. In the signal-chain hierarchy it sits between the sensor front end and the ADC stage of a precision data acquisition system. The INA101HP's headline features include low offset voltage of 25 uV max, low drift of 0.25 uV/C max, nonlinearity of 0.002% max, low input noise of 13 nV/sqrt(Hz), and very high input impedance of 10^10 ohm. These bipolar-architecture specifications were benchmark-setting when Burr-Brown introduced the family and remain competitive for DC-precision bridge applications. The three-op-amp internal architecture places precision input buffers ahead of a difference amplifier, so source-impedance imbalance does not degrade CMRR, which reaches high values at 60 Hz. Gain is programmed from 1 V/V to over 1000 V/V with one external resistor RG, giving bandwidth up to approximately 300 kHz at low gains and 0.04 V/us slew rate. Typical applications include strain-gauge bridge amplification, thermocouple and RTD temperature measurement, medical biopotential front ends such as ECG, and general-purpose low-level data acquisition where microvolt-level offsets cannot be tolerated. Design consideration: gain accuracy and CMRR depend on careful layout and a clean, low-impedance reference pin; always return the REF pin to a low-impedance ground or driven reference rather than a resistor divider. This page adds value beyond the manufacturer datasheet by consolidating drop-in alternative analysis, pricing context, design notes, and application guidance in one citable reference.

RFQ تماس
INA101HP-1 Instrumentation Amplifier | Texas Instruments
INA101HP-1

INA101HP-1 Instrumentation Amplifier | Texas Instruments

Texas Instruments INA101HP-1 is a very-high-accuracy instrumentation amplifier designed for low-level signal amplification and general-purpose data acquisition. It provides selectable voltage gains from 1 to 1000 V/V, a 300 kHz gain-bandwidth product at a gain of 1, 25 uV maximum input offset voltage, and 13 nV/sqrt(Hz) input noise. The device is supplied in a 14-pin PDIP package for through-hole PCB installation. Three precision operational amplifiers and laser-trimmed metal-film resistors are integrated on one monolithic IC. An instrumentation amplifier is a specialized analog signal-conditioning amplifier for differential sensors and other low-level sources. Its internal three-op-amp architecture rejects common-mode interference while preserving a small differential signal. The INA101HP-1 belongs to the instrumentation-amplifier category within the broader hierarchy of amplifier ICs, analog integrated circuits, and semiconductor signal-conditioning devices. This makes it suitable where a sensor output must be amplified before being measured by an ADC or processed by a control system. The main performance advantages are low drift of 0.25 uV/degree C maximum, low offset of 25 uV maximum, and low nonlinearity of 0.002%. A high input impedance of 10 Gohm prevents the amplifier from significantly loading the source. Its single integrated design also reduces the number of external precision resistors and op-amps required to build a conventional three-op-amp instrumentation-amplifier circuit. These characteristics are especially useful for strain measurements, bridge circuits, and precision analog measurement systems. The INA101 integrates three precision operational amplifiers with laser-trimmed metal-film resistors. Gain is selected through external connections, while the internal resistor network provides repeatable ratios without requiring a collection of closely matched external resistors. At unity gain, bandwidth reaches 300 kHz; bandwidth falls as gain increases because the closed-loop feedback network must preserve accuracy at lower signal frequencies. Input voltage and supply rails must be selected so that every internal amplifier remains within its operating limits. Typical uses include low-level strain-gauge and bridge excitation measurements, precision data-acquisition channels, industrial process-control inputs, and sensor interfaces where common-mode voltage varies substantially between the input terminals. The instrumentation-amplifier topology is particularly useful when the wanted signal is small relative to the common-mode voltage. Its through-hole PDIP package also suits legacy control boards, educational platforms, and instrumentation prototypes where surface-mount assembly is unnecessary. When designing a board around INA101HP-1, follow the manufacturer pinout and reference configuration for input polarity, gain selection, reference connection, and supply bypass capacitors. Keep sensor inputs away from switching nodes and high-current return paths, and terminate unused inputs according to the device recommendations. Verify the selected gain against the bandwidth, output swing, and supply limits before beginning calibration. This page organizes the technical specifications, verified sourcing information, package details, application guidance, and same-package replacement options for the INA101HP-1. It also provides comparison-oriented design notes intended to accelerate component selection, board bring-up, and precision analog signal-chain planning.

RFQ تماس
INA101KU - High Accuracy Instrumentation Amp | Texas Instruments
INA101KU

INA101KU - High Accuracy Instrumentation Amp | Texas Instruments

The Texas Instruments INA101KU is a very high accuracy instrumentation amplifier with 25 uV maximum input offset voltage, 0.25 uV/C maximum offset drift, and 0.002% maximum nonlinearity, housed in a 16-pin SOIC (DW, SOL-16) surface-mount package. An instrumentation amplifier is a specialized differential amplifier designed to amplify small sensor signals while rejecting common-mode noise. It sits at the front end of the signal chain hierarchy: sensor -> instrumentation amplifier -> filter -> ADC. Unlike a standard op amp, an instrumentation amplifier provides a user-set gain via a single external resistor, extremely high common-mode rejection (CMR at 60 Hz), very high input impedance, and matched, high-impedance differential inputs, making it the standard choice for precision bridge and transducer readout. Key features of the INA101KU include 13 nV/Hz input-referred voltage noise, high common-mode rejection at 60 Hz (targeted at 50/60 Hz line-noise rejection), input impedance of 10^10 ohm, and a classic three-amplifier topology on a single monolithic die. These parameters directly improve system accuracy: the 25 uV offset and 0.25 uV/C drift eliminate the need for external offset trimming in most strain-gage applications, and 0.002% nonlinearity preserves end-to-end measurement integrity over a wide gain range. Architecturally, the INA101 uses three internally compensated amplifiers configured as a classic two-stage instrumentation amplifier, with gain set by one external resistor RG (G = 1 + 40 kOhm/RG). It operates from dual supplies of +/-5 V to +/-20 V with a slew rate of 0.4 V/uS and a bandwidth of approximately 25 kHz, sufficient for static and low-frequency dynamic measurements. Typical applications include strain-gage bridge amplifiers, thermocouple and RTD conditioning, weigh scales, low-level data acquisition front ends, and medical transducer interfaces where microvolt-level signals must be amplified in electrically noisy environments. Design consideration: at high gains, keep the gain resistor RG traces short and use a low-drift, low-TCR resistor, since RG mismatch and self-heating directly degrade gain accuracy and drift. This page synthesizes distributor pricing, drop-in alternatives, cross-reference data, and practical design notes not consolidated in the manufacturer datasheet.

RFQ تماس
INA101KU/1K - High Accuracy Instrumentation Amplifier | TI
INA101KU/1K

INA101KU/1K - High Accuracy Instrumentation Amplifier | TI

The Texas Instruments INA101KU/1K is a very high accuracy instrumentation amplifier with 25 uV maximum offset voltage, 0.25 uV/C maximum offset drift, and 0.002% maximum nonlinearity, housed in a 16-pin SOIC (DW) surface-mount package. An instrumentation amplifier is a specialized differential amplifier designed to amplify the difference between two input signals while rejecting common-mode voltage. Unlike a general-purpose operational amplifier, an instrumentation amplifier (in-amp) provides a fixed or gain-set internal architecture, very high input impedance, and high common-mode rejection, making it a key building block in the precision analog signal chain hierarchy: instrumentation amplifier -> precision amplifier -> analog front end -> signal conditioning system. Key features include ultra-low input offset voltage of 25 uV max, low offset temperature drift of 0.25 uV/C max, nonlinearity of just 0.002%, and low input noise of 13 nV/sqrt(Hz). The device also provides high common-mode rejection at 60 Hz and very high input impedance of 10^10 ohms, which allows direct connection to high-impedance sources such as strain gauge bridges without loading errors. The INA101 architecture integrates three internally matched operational amplifiers with a single external resistor setting the gain, preserving offset and drift performance across the gain range that would be difficult to achieve with discrete op-amp designs. Gain is configured via external resistor according to the manufacturer datasheet formula, enabling gains from 1 to over 1000 V/V. Typical applications include strain gauge and weigh-scale bridge amplification, thermocouple and RTD temperature measurement front ends, industrial process-control signal conditioning, and medical biopotential acquisition where microvolt-level signals must be extracted in the presence of large common-mode interference such as 50/60 Hz mains hum. When designing with the INA101KU/1K, keep gain-setting resistor traces short and use low-drift resistors to avoid degrading the intrinsic 0.25 uV/C offset drift. Careful grounding and a guard ring around the input pins preserve the high input impedance and CMR at 60 Hz. This page synthesizes distributor pricing, verified drop-in alternatives, practical design notes, and application guidance not found in the manufacturer datasheet alone.

RFQ تماس
INA101KUE4 - High-Accuracy Instrumentation Amplifier | TI
INA101KUE4

INA101KUE4 - High-Accuracy Instrumentation Amplifier | TI

The Texas Instruments INA101KUE4 is a high-accuracy instrumentation amplifier with three internal amplifiers, a 300 kHz bandwidth, 250 uV input offset voltage, and single-ended output capability, packaged in a 16-pin SOIC. It is designed for precision differential-signal conditioning where high input impedance, common-mode rejection, and adjustable gain are important. The device is suitable for sensor interfaces, industrial measurement systems, medical instrumentation, and laboratory equipment. An instrumentation amplifier is a specialized amplifier that combines differential input, high input impedance, and precise gain-setting behavior in one integrated circuit. Its functional position is signal conditioning within the broader amplifier IC category: sensor output -> instrumentation amplifier -> ADC or signal-processing circuit. Unlike a general-purpose operational amplifier, an instrumentation amplifier is optimized for measuring small differential signals riding on a larger common-mode voltage, which helps preserve signal integrity in precision measurement systems. The INA101KUE4 uses a three-amplifier architecture to provide high input impedance and accurate differential gain. Its stated bandwidth is 300 kHz, while the input offset voltage is 250 uV. The manufacturer describes the device as a high-accuracy instrumentation amplifier, and its single-ended amplifier output supports conversion of a differential input into a ground-referenced signal for downstream data conversion. An external resistor network sets the closed-loop gain according to the manufacturer's recommended circuit. The main design trade-off is bandwidth versus precision. A 300 kHz bandwidth is suitable for many pressure, temperature, bridge-sensor, and general industrial measurement signals, but it is not intended for high-frequency waveform systems requiring megahertz-class signal bandwidth. Input common-mode range, output swing, supply voltage, and gain-error limits must be checked against the actual sensor output and the selected supply rails before the circuit is finalized. Typical uses include low-level bridge and strain-gauge conditioning, medical sensor instrumentation, current-shunt measurement, precision current sensing, laboratory test equipment, and industrial process-control modules. In each case, the differential input architecture helps reject common-mode disturbance when the measured signal is small relative to the surrounding voltage range. Place the gain-setting resistor directly at the amplifier pins and use a quiet reference or regulated supply for analog circuitry. Keep input and feedback traces short, use a solid ground plane, and decouple each supply rail close to the device. Check input and output common-mode limits across temperature, because operation near either range boundary can reduce usable signal swing even when the supply voltage itself is adequate. This product page combines the INA101KUE4 device identity, verified package and performance details, sourcing information, replacement guidance, and practical circuit-design notes. It is intended to help engineers compare the exact INA101KUE4 ordering code against compatible alternatives while recognizing that instrumentation-amplifier pin compatibility must be confirmed at the individual-pin level.

RFQ تماس
INA101SG - Military High Accuracy Instrumentation Amplifier | TI
INA101SG

INA101SG - Military High Accuracy Instrumentation Amplifier | TI

The Texas Instruments INA101SG is a very high accuracy instrumentation amplifier, originally introduced by Burr-Brown, delivered in a 14-pin ceramic DIP (CDIP-14) package and qualified to a military temperature grade. Headline specifications include a maximum offset voltage drift of 0.25 uV/C, a maximum input offset voltage of 25 uV, and low nonlinearity of 0.002%, with input voltage noise of 13 nV/Hz. An instrumentation amplifier is a specialized differential amplifier designed to amplify the small difference between two input signals while rejecting any voltage common to both inputs. Within the signal-chain hierarchy (instrumentation amplifier -> precision differential amplifier -> operational amplifier -> analog front end), it provides the high common-mode rejection and high input impedance that single op-amp stages cannot achieve, making it the standard front end for bridge transducers and low-level sensor signals. Key features of the INA101SG include its three-op-amp topology with laser-trimmed metal-film resistors integrated on a single monolithic die, which delivers the tight resistor matching responsible for 0.002% nonlinearity and high CMR at 60 Hz. Input impedance is approximately 10^10 ohms, so the device loads bridges and high-impedance sources negligibly. Gain is set by a single external resistor, and the ceramic DIP package supports hermetic, high-reliability military and aerospace assemblies. The bipolar process and precision trimming give the INA101 family its signature combination of microvolt-level offset and sub-microvolt-per-degree drift. Compared with discrete three-op-amp front ends, the monolithic construction guarantees resistor ratio tracking over temperature, which is the dominant error source in precision differential measurements. Typical applications include strain-gauge bridge amplification, thermocouple and RTD signal conditioning, and general-purpose data-acquisition front ends where low-level differential signals must be amplified with minimal added error. Design-wise, keep gain-setting resistor leads short and use a Kelvin ground for the reference pin; offset and drift specifications are guaranteed only when the reference pin is driven from a low-impedance source. This page synthesizes verified distributor data, family cross-references, and practical design guidance not consolidated in the manufacturer datasheet.

RFQ تماس
INA101SM - High Accuracy Instrumentation Amplifier | TI
INA101SM

INA101SM - High Accuracy Instrumentation Amplifier | TI

The Texas Instruments INA101SM is a very high accuracy instrumentation amplifier for low-level signal amplification and general-purpose data acquisition, packaged in a 10-pin TO-100 package. It integrates three precision operational amplifiers and laser-trimmed metal-film resistors on one monolithic IC. The verified data identifies a maximum input offset voltage of 25 uV, maximum input drift of 0.25 uV/°C, low nonlinearity of 0.002%, and input-referred noise of 13 nV/√Hz. These characteristics make the device suitable for precision bridge, strain-gauge, sensor, and biomedical signal-chain designs where offset and drift errors must remain small relative to the measured signal. An instrumentation amplifier is a specialized differential amplifier optimized for measuring small signals superimposed on a large common-mode voltage. Its internal gain-setting network and three-op-amp architecture provide high input impedance, controlled gain, and strong common-mode rejection. In the broader semiconductor hierarchy, an instrumentation amplifier is an analog signal-conditioning amplifier, a linear amplifier, and ultimately an integrated circuit used within data-acquisition and measurement systems. The INA101 is intended to preserve signal integrity from sensor excitation through differential amplification. Key features include a 13 nV/√Hz noise density, 25 uV maximum offset voltage, 0.25 uV/°C maximum drift, and 0.002% low nonlinearity. Its integrated precision resistors reduce external gain-setting components and help establish repeatable performance between assemblies. The high input impedance prevents the amplifier from significantly loading the source, while common-mode rejection is important when the wanted differential signal is much smaller than the voltage shared by both input terminals. The verified data describes the INA101 as a monolithic integrated circuit combining three precision op amps with laser-trimmed metal-film resistors. The design is suited to precision amplification of differential inputs rather than single-ended audio or general logic signals. Comparison information identifies a typical dual-supply condition of ±15 V, with an indicated minimum of ±5 V and maximum of ±20 V; maximum power dissipation is listed as 600 mW. These operating details must be checked against the complete manufacturer datasheet for design limits and test conditions. Typical applications include strain-gauge bridge excitation and measurement, low-level sensor acquisition, biomedical instrumentation, and general-purpose differential data acquisition. In a bridge circuit, the small millivolt-level differential output can be amplified while the instrumentation amplifier rejects common-mode excitation and prevents source loading. In biomedical or industrial measurement systems, the combination of low offset, low drift, and high input impedance helps preserve measurements over time and across varying source impedances. Designers should confirm the exact pin assignments, gain configuration, supply sequencing, common-mode range, and output-swing limits in the manufacturer datasheet before layout. Because this through-hole TO-100 device can dissipate up to 600 mW according to the verified comparison data, adequate PCB copper and thermal spacing should be provided. Input and reference-ground connections should be kept short, and the gain-setting method should follow the datasheet's recommended resistor topology. This page combines verified manufacturer and distributor information, source traceability, application guidance, and a disciplined alternative assessment. The available cross-reference results did not establish five verified, pin-compatible drop-in parts in the same package, so no unsupported replacements are presented as drop-in equivalents.

RFQ تماس
INA103KP - 6 MHz Low-Noise Instrumentation Amplifier | TI
INA103KP

INA103KP - 6 MHz Low-Noise Instrumentation Amplifier | TI

The Texas Instruments INA103KP is a low-noise, low-distortion monolithic instrumentation amplifier with 1 nV/√Hz noise density, 6 MHz bandwidth, and greater than 100 dB common-mode rejection in a 16-pin PDIP package. Designed for differential low-level signal acquisition, it combines current-feedback circuitry, internal gain-setting resistors, and a wide ±25 V supply range. The INA103KP is particularly suited to balanced low-impedance microphone and other precision audio inputs, where low source impedance allows the amplifier to approach its theoretical noise-performance limit. An instrumentation amplifier is a differential amplifier optimized for measuring small signals superimposed on larger common-mode voltages. Its internal architecture provides accurate differential gain while rejecting common-mode interference, making it more suitable than a general-purpose op amp when source signals are balanced, sensor outputs are small, or grounding noise is difficult to control. The INA103KP belongs to the broader signal-conditioning IC hierarchy: instrumentation amplifier, differential amplifier, analog signal-conditioning IC, and semiconductor. The device offers a 6 MHz gain-bandwidth product, 1 nV/√Hz input-noise density, and common-mode rejection greater than 100 dB. Its current-feedback topology supports wide bandwidth and fast dynamic response. Internal gain-setting resistors simplify circuit construction, while the manufacturer identifies the INA103 as an upgrade path for designs previously based on the AD625. These characteristics allow low-level signals to be amplified without relying on an extremely high closed-loop gain. Typical uses include balanced low-impedance microphones, low-level audio acquisition, industrial measurement systems, instrumentation interfaces, and precision differential sensor inputs. The 16-pin PDIP package provides through-hole accessibility and straightforward prototype assembly. Its relatively high bandwidth makes it suitable for signals extending beyond conventional audio-band instrumentation, although system-level filtering and stability analysis remain necessary. A primary design consideration is source impedance. The manufacturer states that near-theoretical noise performance is obtained with a 200 Ω source impedance, so cable, microphone, or transducer impedance directly affects achievable signal-to-noise ratio. Designers should also verify supply headroom, input common-mode range, gain configuration, output swing, and stability for the selected feedback network using the manufacturer datasheet. This product data combines manufacturer specifications, current distributor evidence, application guidance, and explicitly identified gaps. It distinguishes verified drop-in replacement evidence from merely similar or functionally equivalent parts, helping engineers avoid treating package-compatible substitution as a safe assumption.

RFQ تماس
INA103KU - Low-Noise Instrumentation Amplifier | Texas Instruments
INA103KU

INA103KU - Low-Noise Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA103KU is a low-noise, low-distortion monolithic instrumentation amplifier with one amplifier circuit, a 16-SOIC package, a gain bandwidth of 6 MHz, and a slew rate of 15 V/s. It operates from a single supply between 9 V and 25 V and provides near-theoretical noise performance for source impedances near 200 ohms. An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two input terminals while rejecting common-mode signals. Its internal gain network and feedback architecture provide high input impedance, accurate differential gain, and better rejection of shared interference than a general-purpose operational amplifier. The INA103KU is therefore positioned between precision operational amplifiers and higher-cost precision measurement amplifiers. The INA103 uses current-feedback circuitry to achieve a 6 MHz gain-bandwidth product and a 15 V/s slew rate. Its low-noise design is suitable for extracting weak signals without requiring a high signal frequency. The manufacturer identifies balanced, low-impedance microphone signals as a primary use case, while the differential input architecture also supports sensor bridges, current measurement, laboratory instrumentation, and industrial receiver front ends. The component supports single-ended and differential signal arrangements and accommodates source impedances around 200 ohms with near-theoretical noise performance. Its maximum output offset voltage listed for the INA103KU is 250 µV. Because its supply range is 9 V to 25 V, the device is intended for higher-voltage analog systems rather than low-voltage mixed-signal rails where a modern rail-to-rail amplifier may be more appropriate. Typical applications include balanced low-impedance microphones, audio equipment, industrial sensor interfaces, pressure and strain-gauge bridges, current shunts, and precision measurement front ends. The 16-SOIC package provides a conventional surface-mount footprint and supports integration into analog signal-conditioning boards, instrument preamplifiers, and multi-channel measurement systems. Designers should verify gain settings, source impedance, bandwidth, output swing, and supply headroom against the manufacturer datasheet. Input and output filtering should be selected for the source impedance and signal bandwidth, while adequate bypassing should be placed close to the supply pins to preserve low-noise operation. This product page combines manufacturer specifications, application guidance, package information, and verified drop-in family options. It also highlights the INA103KU's operating envelope, making it easier to compare it with other instrumentation amplifiers before committing to a high-voltage analog design.

RFQ تماس
INA105AM - Unity-Gain Differential Amplifier | Texas Instruments
INA105AM

INA105AM - Unity-Gain Differential Amplifier | Texas Instruments

The Texas Instruments INA105AM is a precision unity-gain differential amplifier with a nominal gain of 1, minimum common-mode rejection of 86 dB over temperature, maximum gain error of 0.01%, and maximum nonlinearity of 0.001%. It is packaged in an 8-pin TO-99 metal package. The device combines a precision operational amplifier with a laser-trimmed on-chip metal-film resistor network. A differential amplifier is an analog signal-conditioning circuit that subtracts one input voltage from another. By rejecting signals common to both inputs and amplifying the remaining difference, it supports accurate measurement in systems where the useful signal is small relative to a larger common-mode voltage. The INA105 belongs to the operational-amplifier and instrumentation-amplifier hierarchy within analog and power-management electronics. Laser trimming of the internal resistor network provides accurate unity gain without external gain-setting resistors. The matching temperature coefficient of the network helps preserve gain accuracy and common-mode rejection as temperature changes. These characteristics make the INA105AM useful when a differential signal must be converted into a single-ended voltage with low gain error and high rejection of shared noise or interference. Typical uses include instrumentation, bridge-amplifier interfaces, current-sense signal conditioning, precision amplifier front ends, and measurement systems in which both input sources operate around a common voltage. The TO-99 package provides a mechanically robust through-hole form factor for industrial and laboratory equipment, although the larger package is less compact than an SOIC-8 implementation. The principal design consideration is input-voltage compatibility. The input common-mode range, supply limits, input bias current, and output swing must be checked against the signal source before deployment. Decoupling capacitors should be placed close to the supply pins, and source impedances should be balanced when maximum common-mode rejection is required. The manufacturer datasheet should be used for the complete pin description and electrical limits. This page combines the manufacturer device description, package information, verified specifications, and engineering guidance to clarify selection and implementation. It also distinguishes the documented INA105AM ordering option from alternatives that require a package or electrical review before substitution.

RFQ تماس
INA105BM - Unity Gain Differential Amplifier, 1 MHz | Texas Instruments
INA105BM

INA105BM - Unity Gain Differential Amplifier, 1 MHz | Texas Instruments

The Texas Instruments INA105BM is a precision unity-gain differential amplifier with a 1 MHz gain-bandwidth product, packaged in an 8-lead TO-99 metal can (TO-99-8). The device is a monolithic gain = 1 differential amplifier built from a precision operational amplifier and an on-chip laser-trimmed metal film resistor network, so the differential gain and common-mode rejection are set by the factory-trimmed network rather than by external resistors. An instrumentation amplifier is a differential amplifier optimized for measuring small signals riding on a large common-mode voltage. This INA105 variant is the fixed unity-gain member of that family: it is used when a designer needs accurate subtraction of two input voltages without building a discrete four-resistor difference network. The INA105 family is offered in 8-pin plastic DIP, SOIC surface-mount, and TO-99 metal can packages, and the BM suffix denotes the round metal-can, wire-lead industrial-grade orderable. Key characteristics of the INA105BM include a fixed unity differential gain of 1, a 1 MHz small-signal bandwidth as specified for this device, an integrated laser-trimmed metal film gain network, and a single-amplifier topology that needs no external gain-setting resistors. Because the gain network is on-chip, temperature drift and tolerance of the network are trimmed at the factory, which simplifies calibration and removes the resistor-matching problems that dominate discrete difference amplifiers. Technically, the INA105BM combines a precision op-amp core with four matched, thin-film metal film resistors forming a differential-to-single-ended unity-gain network. Common-mode rejection depends directly on the matching of this on-chip network, which is why the device is laser trimmed. The single differential amplifier inside the package means the part consumes less board area than a discrete difference stage and requires only bypass capacitors on the supply pins plus output decoupling for stable operation. Typical applications include precision bridge and strain-gauge front ends, shunt current measurement in power-conversion and motor-control circuits, low-level differential sensor conditioning, laboratory and medical instrumentation, and differential receiver stages for balanced audio and communications lines. Anywhere a clean differential signal must be converted to a single-ended signal referenced to ground, the unity-gain topology removes the need for external feedback resistors. The key design consideration is common-mode range. A unity-gain differential amplifier can only reject common-mode voltage while both inputs stay inside the input common-mode range of the internal op amp, and the TO-99 metal can is a through-hole package intended for legacy and industrial instrumentation where lead spacing, not footprint area, dominates board layout. Keep the input pair shielded from switching nodes and route them as a tightly coupled differential pair. This page consolidates the manufacturer product description, package and ordering details, structured specification coverage, drop-in ordering-code alternatives in the same TO-99-8 footprint, and practical design notes into a single engineering reference that goes beyond the brief distributor catalogue listing.

RFQ تماس
INA105KP - Unity-Gain Precision Differential Amplifier | Texas Instruments
INA105KP

INA105KP - Unity-Gain Precision Differential Amplifier | Texas Instruments

The Texas Instruments INA105KP is a precision unity-gain differential amplifier, a monolithic gain = 1 differential amplifier built from a precision operational amplifier and an on-chip laser-trimmed metal-film resistor network, packaged in an 8-pin PDIP (P suffix) package. Key headline parameters are a unity differential gain of 1.000 (0.05% typical gain error class), a minimum CMRR of 86 dB, a common-mode input range that extends beyond the supply rails (down to -20 V), a 1 MHz gain-bandwidth product, and a maximum input offset voltage of 500 uV, with a -40 °C to +85 °C ambient operating range and a total supply voltage span of 10 V to 36 V (single 5 V to 36 V or dual +/-5 V to +/-18 V). A differential amplifier is a circuit block that accepts two input voltages and produces an output equal to their difference. It is a sub-type of instrumentation amplifier architecture, and it sits in the hierarchy: differential amplifier -> instrumentation amplifier family -> analog signal conditioning IC -> semiconductor. Unlike a general-purpose operational amplifier, the INA105 integrates matched, laser-trimmed resistors so the differential gain and common-mode rejection are accurate from the factory without any external precision resistor network. Because the on-chip resistors are laser trimmed for accurate gain and high common-mode rejection, and because their temperature coefficient (TCR) tracking is excellent, both the gain accuracy and the CMRR remain stable over the operating temperature range. The input common-mode range extends beyond the positive and negative supply rails, which lets the part accept signals that would forward-bias the input protection diodes of a bare op amp. The unity-gain topology is deliberate: the INA105 replaces a discrete precision resistor network in balanced line, bridge, and current-shunt measurement circuits. Because gain is fixed at 1, there is no external gain-setting resistor to drift, and the device is often placed directly in front of a higher-gain stage when extra gain is required. Typical uses include 4-20 mA loop receivers, bridge and load-cell front ends, precision current-shunt amplifiers in power-conversion and motor-control loops, balanced differential receivers for RS-485 and CAN physical layers, and instrumentation signal chains in test and measurement equipment. The main design consideration is reference grounding: the REF pin must be tied to the analog ground of the system so that the output reference matches the receiver's common-mode window. Because this is a linear bipolar amplifier rather than a switching or chopper-stabilized part, offset and drift are set by the underlying op-amp architecture, so keep the layout short and symmetrical. This page brings together the pin configuration, parameter-by-parameter comparison against drop-in alternatives, and practical layout and reference-grounding notes that are not consolidated in a single place in the original manufacturer documentation.

RFQ تماس
INA105KU - Unity-Gain Differential Amplifier | Texas Instruments
INA105KU

INA105KU - Unity-Gain Differential Amplifier | Texas Instruments

The Texas Instruments INA105KU is a precision unity-gain differential amplifier with one amplifier channel, an 8-pin SOIC package, 500 uV typical input offset voltage, 1 MHz bandwidth, and an operating temperature range of -40°C to +85°C. It is designed for systems that need accurate differential-to-single-ended signal conversion without external gain-setting resistors. A unity-gain differential amplifier is an analog signal-conditioning device that compares two input voltages and produces an output proportional to their difference. The INA105 integrates a precision operational amplifier with a laser-trimmed on-chip metal-film resistor network, placing it in the hierarchy of differential amplifier, instrumentation signal conditioner, analog amplifier IC, and semiconductor. The principal benefits of the INA105 include a minimum common-mode rejection ratio of 86 dB over temperature, maximum gain error of 0.01%, and maximum nonlinearity of 0.001%. The matched, laser-trimmed resistor network improves gain accuracy and common-mode rejection without external adjustments. The unity-gain configuration also simplifies system design when the desired circuit function is VOUT equal to VIN+ minus VIN-. The device accepts differential input signals while rejecting common-mode voltage present on both inputs. This makes it useful in current-sense measurement, instrumentation, signal isolation, audio front ends, and industrial signal-conditioning systems. Its SOIC-8 surface-mount package supports compact analog boards while providing separate supply, reference, input, output, and resistor-network connections. Typical uses include differential sensor interfaces, bridge-amplifier signal paths, balanced audio inputs, and precision measurement systems. For each application, input and output filtering should be selected according to the signal bandwidth and noise requirements. The reference connection should be handled carefully in single-supply systems because it establishes the output reference point. The key design consideration is common-mode and output-range compatibility. The input common-mode range must include the signal being measured, and the output must remain within the amplifier's output-voltage range at the selected supply voltage. Check the datasheet limits for input common-mode voltage, output swing, supply voltage, and load current before finalizing the board. This page combines the INA105KU electrical characteristics, package information, pin assignment, application guidance, design checks, and available cross-reference information to support faster component selection and board-layout planning.

RFQ تماس
INA106KP - Precision Gain 10 Differential Amplifier | Texas Instruments
INA106KP

INA106KP - Precision Gain 10 Differential Amplifier | Texas Instruments

The Texas Instruments INA106KP is a precision fixed-gain differential amplifier with a nominal gain of 10, supplied in an 8-pin plastic DIP package. It integrates a precision operational amplifier with on-chip metal-film resistors, and the resistor network is laser trimmed for accurate gain and high common-mode rejection. The fixed gain architecture simplifies instrumentation circuits that require differential input measurement without external gain-setting resistors. The verified product data identifies INA106KP as a one-circuit, 8-pin differential amplifier. A differential amplifier is a circuit that amplifies the voltage difference between two input terminals while rejecting common-mode signals. In the broader semiconductor hierarchy, the INA106KP belongs to the instrumentation amplifier and special-purpose amplifier family, within the amplifier IC and analog signal-processing categories. Its integrated precision resistor network is designed to improve gain accuracy and common-mode rejection while reducing the number of external components required in sensor, bridge, and measurement applications. The INA106 family is specified as a gain-of-10 differential amplifier. The manufacturer describes the device as using a precision operational amplifier together with on-chip metal-film resistors. These resistors are laser trimmed for accurate gain and high common-mode rejection, while their temperature coefficient tracking is intended to preserve gain accuracy and CMRR over temperature. The available verified data does not provide the complete electrical limits, so detailed voltage, current, bandwidth, and temperature specifications are marked as data needed below rather than estimated. Typical uses include conditioning low-level differential sensor signals, bridge outputs, current-shunt measurements, and industrial instrumentation where a fixed gain of 10 is suitable. Because the gain is integrated and fixed, the device is most useful when the system designer wants repeatable gain accuracy without selecting and balancing external precision resistors. The PCB footprint should use the manufacturer’s 8-pin plastic DIP drawing, with supply and signal routing completed according to the datasheet’s recommended layout. A key design consideration is that the INA106KP is not a general-purpose unity-gain op-amp substitute. Its fixed gain, internal resistor network, input topology, supply requirements, and pin functions must match the original circuit. Designers should confirm differential input range, common-mode range, output swing, supply voltage, noise, and stability requirements against the current INA106 datasheet before production use. This page consolidates verified manufacturer and distributor information, documented package details, engineering application guidance, and a strict drop-in replacement review. It distinguishes confirmed INA106KP facts from parameters that require confirmation from the manufacturer datasheet, helping engineers shortlist the part without presenting unverified electrical values as facts.

RFQ تماس
INA106U - Gain 10 Differential Amplifier | Texas Instruments
INA106U

INA106U - Gain 10 Differential Amplifier | Texas Instruments

The Texas Instruments INA106U is a precision fixed-gain differential amplifier with a nominal gain of 10, 86 dB minimum common-mode rejection, and an 8-pin SOIC package. The device is designed for accurate differential measurement and signal conditioning where common-mode noise must be rejected before downstream amplification or conversion. Its monolithic construction combines a precision operational amplifier with laser-trimmed on-chip metal-film resistors. A differential amplifier is a circuit that amplifies the voltage difference between two input terminals while suppressing voltage common to both inputs. In the signal-chain hierarchy, differential amplification sits between sensors or front ends and higher-gain analog processing. The INA106 family is commonly used for bridge, current, and instrumentation-amplifier input stages where preserving small differential signals is more important than accepting large common-mode signals. Key documented features include accurate gain of ±0.025% maximum, common-mode rejection of 86 dB minimum, and nonlinearity of 0.001% maximum. The laser-trimmed resistor network is intended to maintain accurate gain and common-mode rejection over temperature. The manufacturer describes applications including a gain-of-10 differential amplifier, a -10 amplifier, and a +11 amplifier configuration. The available INA106 family packages include 8-pin plastic DIP and SOIC options, while INA106U specifically denotes the SOIC ordering variant. The internal architecture is important because the matched resistor network determines gain accuracy and common-mode behavior. Unlike a discrete implementation using an operational amplifier and four external resistors, the integrated approach reduces resistor-matching variability and simplifies the physical circuit. The device should be evaluated against its complete datasheet electrical limits, including supply voltage, input range, output swing, frequency response, and temperature limits. Typical applications include precision bridge excitation and sensing, instrumentation front ends, current measurement, sensor signal conditioning, and rejection of common-mode noise in industrial control systems. The SOIC-8 package is suitable for conventional surface-mount assembly, but exposed thermal performance and output-drive limits still depend on the exact operating conditions. For layout, keep input traces short and symmetric, provide a clean reference connection, and place input filtering close to the amplifier. Confirm common-mode and output-swing limits before selecting external gain resistors or adding downstream gain. The fixed internal gain also means changing the system gain generally requires a different amplifier rather than an external resistor adjustment. This page combines the verified Texas Instruments product and datasheet information, distributor references, package guidance, and practical selection considerations. It is intended to help engineers identify whether the INA106U fixed-gain architecture matches the required accuracy, common-mode rejection, package, and supply conditions.

RFQ تماس
INA106UG4 - Gain 10 Differential Amplifier | Texas Instruments
INA106UG4

INA106UG4 - Gain 10 Differential Amplifier | Texas Instruments

The Texas Instruments INA106UG4 is a precision, fixed-gain differential amplifier with a gain of 10, housed in an 8-pin SOIC package. It integrates a precision operational amplifier with laser-trimmed on-chip metal-film resistors, providing a compact way to amplify small differential signals. The monolithic gain stage is intended for instrumentation systems where a fixed gain of 10 is useful and external resistor matching is undesirable. A differential amplifier is an analog signal-conditioning circuit that responds to the voltage difference between two inputs while rejecting voltage common to both inputs. In the signal-chain hierarchy, the INA106UG4 belongs to the instrumentation amplifier family, combining differential amplification, fixed-gain accuracy, and common-mode rejection in one integrated package. This simplifies precision measurement designs compared with a discrete operational amplifier and matched external resistor network. The defining feature of the INA106UG4 is its gain of 10, implemented with on-chip metal-film resistors that are laser trimmed for accurate gain and high common-mode rejection. Excellent resistor tracking maintains gain accuracy and common-mode rejection over temperature. These characteristics make the device appropriate for sensor interfaces, bridge-amplifier signal paths, and instrumentation requiring repeatable differential-to-single-ended conversion. The INA106 architecture combines a precision operational amplifier with integrated gain-setting elements. Because the gain is fixed internally, designers do not need to select and match external resistors to obtain a gain of 10. The 8-pin SOIC package supports conventional surface-mount assembly and provides a practical option for compact analog boards requiring more integration than a basic single-ended op amp. Typical uses include low-level sensor conditioning, differential measurement interfaces, industrial instrumentation, and analog test equipment. In a bridge-based measurement, the amplifier can increase the differential bridge output before an ADC or downstream signal-processing stage. Its fixed gain simplifies gain planning, although the complete system must still satisfy input common-mode range, output swing, supply-voltage, and noise requirements. When laying out an INA106UG4 circuit, use a quiet ground reference and route differential inputs as a compact, symmetrical pair to minimize conversion of common-mode noise into differential error. Place input and output decoupling capacitors according to the manufacturer datasheet and avoid long unprotected traces around high-impedance source nodes. Verify signal polarity before applying large inputs because the fixed gain also amplifies offset and noise. This product page combines the manufacturer's device description and ordering information with package details, application guidance, parameter-by-parameter comparison, and practical design notes. It helps engineers distinguish the INA106UG4 from other differential-amplifier options while focusing on verified gain, architecture, package, sourcing, and circuit-integration considerations.

RFQ تماس
INA110KP - Fast-Settling FET-Input Instrumentation Amplifier | TI
INA110KP

INA110KP - Fast-Settling FET-Input Instrumentation Amplifier | TI

Texas Instruments INA110KP is a monolithic FET-input instrumentation amplifier with internal gains of 1, 10, 100, 200, and 500 V/V, a 2.5 MHz bandwidth, and a 17 V/µs slew rate. The device uses a current-feedback topology and laser-trimmed input stage for accurate, fast-settling signal amplification. It is packaged in a 16-pin plastic DIP (PDIP). An instrumentation amplifier is a differential amplifier optimized for low-level measurements. Its three-amplifier or feedback architecture provides high input impedance, accurate differential gain, and rejection of common-mode voltage. INA110KP is designed for applications where sensor outputs are small, impedance may be high, and measurement speed must exceed that of many precision instrumentation amplifiers. Internal gain-setting resistors simplify implementation by supporting gains of 1, 10, 100, 200, and 500 V/V. Maximum input bias current is 50 pA, helping preserve accuracy with high-impedance sources. The amplifier also provides a minimum common-mode rejection of 106 dB at 10 kHz, low gain drift of 50 ppm/°C, and low offset drift of 2 µV/°C. The current-feedback circuit topology supports a 2.5 MHz bandwidth and 17 V/µs slew rate. According to the manufacturer product page, the INA110 settles to within 0.01% in 4 µs, making it suitable for high-speed and multiplexed-input data-acquisition systems where accurate settling is required after each channel selection. Typical uses include bridge and strain-gauge signal conditioning, high-impedance sensor interfaces, multiplexed measurement systems, laboratory instrumentation, industrial monitoring, and precision current or voltage measurements. The low input bias current is especially useful when source resistance is high enough for input leakage to affect measurement accuracy. Designers should follow the manufacturer pin-description and typical-application circuits when assigning inputs, gain connections, supply bypass capacitors, and output connections. Input filtering and protection must account for the very low 50 pA maximum input bias current. Decoupling and grounding should be arranged to minimize parasitic feedback around the high-bandwidth amplifier. This product page combines the manufacturer's core performance data with application guidance, practical design notes, and a package-matched comparison framework. It is intended to help engineers evaluate settling behavior, gain selection, source impedance, common-mode range, and layout before integrating INA110KP into a measurement system.

RFQ تماس
INA110KPG4 - Fast-Settling FET Instrumentation Amplifier | Texas Instruments
INA110KPG4

INA110KPG4 - Fast-Settling FET Instrumentation Amplifier | Texas Instruments

Texas Instruments INA110KPG4 is a fast-settling, FET-input instrumentation amplifier packaged in a 16-pin PDIP. It accepts supply voltages from ±6 V to ±18 V, provides single-ended output, supports gains of 1, 10, 100, or 1000, and features a 2.5 MHz bandwidth with 500 µV input offset voltage. The device is intended for precision signal-conditioning systems that require high input impedance, low bias current, and accurate differential measurement. An instrumentation amplifier is a specialized amplifier optimized for measuring the difference between two low-level input signals. Its internal architecture provides high input impedance, low output impedance, excellent common-mode rejection, and stable gain set by a resistor or selectable internal gain network. This makes the INA110KPG4 useful when sensor outputs are small, source impedance is high, or the measurement must reject common-mode interference appearing equally on both inputs. The INA110KPG4 combines a 2.5 MHz bandwidth with fast settling, making it suitable for measurement channels that need to respond quickly after a control, excitation, or sensor input changes. Its FET-input stage supports low input bias current, while the 500 µV input offset specification defines the dc error budget for high-gain measurements. The 16-pin PDIP format is appropriate for through-hole prototype boards, laboratory instrumentation, educational systems, and established production assemblies that accept a dual-inline footprint. The amplifier can operate with positive and negative supply rails, allowing the output to remain centered around ground while processing bipolar sensor signals. A reference connection permits output-voltage shifting when the system requires a nonzero midpoint. The available gains of 1, 10, 100, and 1000 allow the same device architecture to cover both high-level measurements and small differential signals without changing packages. Typical uses include bridge-transducer amplification, low-current measurement, biomedical instrumentation, industrial sensor interfaces, laboratory measurement systems, and data-acquisition modules. The device is especially useful when the source impedance is too high for a conventional voltage-amplifier input or when the measured differential signal is much smaller than the surrounding common-mode voltage. When laying out a board, keep the input and output paths short, provide a stable low-noise reference network, and observe the supply-voltage limits of ±6 V to ±18 V. Breadboard connections and long unprotected input tracks should be avoided because leakage, contamination, and parasitic capacitance can degrade accuracy and settling performance. This product page combines package details, operating limits, application guidance, and verified drop-in alternatives. It also provides practical design notes for a legacy bipolar-supply instrumentation amplifier used in sensitive analog measurement systems.

RFQ تماس
INA110KU - 2.5 MHz Fast-Settling Amplifier | Texas Instruments
INA110KU

INA110KU - 2.5 MHz Fast-Settling Amplifier | Texas Instruments

Texas Instruments INA110KU is a monolithic FET-input instrumentation amplifier with 2.5 MHz bandwidth, 4 us settling to 0.01%, and 17 V/us slew rate, housed in a 16-pin SOIC package. It accepts a 12 V to 36 V supply and provides internal gain settings of 1, 10, 100, 200, and 500 V/V. An instrumentation amplifier is a differential analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode interference. The INA110 belongs to the instrumentation amplifier hierarchy within analog amplifiers and signal-chain ICs. Its current-feedback topology, laser-trimmed input stage, very high input impedance, and low input bias current make it suitable for measuring small differential signals through balanced sensors, bridges, and multiplexed data-acquisition inputs. Key features include selectable internal gains of 1, 10, 100, 200, and 500 V/V, a stated input offset voltage of 1 mV, and 2.5 MHz bandwidth. The fast 4 us settling time supports systems that change gain or source between measurements quickly. Input filtering and protection can be placed directly at the high-impedance inputs without loading the source, while the 12 V to 36 V supply range supports higher-compliance analog systems. The current-feedback architecture is intended to provide good dynamic performance while the laser trimming improves gain accuracy and DC behavior. Internal gain-set resistors reduce the number of external components required for fixed-gain designs. Because the device contains FET input stages, it offers very high input impedance and low bias current; this is useful when the source impedance is high or when source resistance differs between the two inputs. Typical applications include high-speed data acquisition, multiplexed sensor measurement, bridge-amplifier interfaces, current measurement, laboratory instrumentation, and industrial signal conditioning. The 4 us settling time is particularly useful when sequential channels must be measured rapidly, while the internal gain choices cover low-level sensor outputs through higher-amplitude differential signals. For layout, keep input and feedback connections short, use symmetric routing between the differential inputs, and place input protection or filtering close to the corresponding pins. Check the external feedback-network requirements for each selected gain and confirm that source impedances remain compatible with the required common-mode range and settling performance. This page combines the manufacturer device specifications with application guidance, package information, replacement analysis, and design-focused comparisons. It highlights where the INA110KU fits in high-speed measurement systems and provides practical context for selecting among same-package alternatives before committing the SOL-16 footprint to a PCB layout.

RFQ تماس
INA110KUG4 - 2.5 MHz Military Instrumentation Amplifier | Texas Instruments
INA110KUG4

INA110KUG4 - 2.5 MHz Military Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA110KUG4 is a single-circuit instrumentation amplifier packaged in a 16-pin SOIC. It is identified as a military-temperature-grade, gull-wing-lead device, and its listed gain-bandwidth product is 2.5 MHz. The INA110KUG4 is intended for systems that require a differential input stage, an adjustable-gain architecture, and a regulated output referenced to a low-impedance analog supply. An instrumentation amplifier is a precision analog building block that amplifies the voltage difference between two input signals while rejecting common-mode interference. Unlike a general-purpose operational amplifier, an instrumentation amplifier normally incorporates a high-impedance differential input stage, accurate gain-setting resistors, and a low-impedance output stage. Within the power-management and signal-chain hierarchy, it sits upstream of analog-to-digital converters, filters, and analog-to-digital output stages. The INA110KUG4 is classified by Texas Instruments as an instrumentation amplifier rather than a standalone operational amplifier. Its adjustable external gain resistor allows the same circuit topology to support multiple sensitivity ranges, provided that resistor values remain suitable for the required bandwidth and stability. The 2.5 MHz gain-bandwidth figure makes the device relevant to moderate-bandwidth sensor conditioning rather than only static measurement systems. Because the INA110KUG4 uses a precision differential input stage, it is suitable for conditioning low-level sensor outputs where common-mode voltage varies relative to the measurement. Typical signal sources include pressure bridges, strain gauges, thermocouples when paired with suitable cold-junction compensation, and high-impedance sensing elements. A reference pin also permits the output voltage to be shifted when the receiving circuit cannot tolerate a ground-centered signal. Common applications include industrial process monitoring, laboratory instrumentation, data acquisition, medical monitoring equipment, and portable measurement systems. In a typical bridge-sensor circuit, the INA110KUG4 amplifies the small differential bridge voltage while rejecting much of the common excitation voltage. The output can then feed an analog-to-digital converter or an analog filter. When laying out a board for the INA110KUG4, keep the gain-setting resistor close to its corresponding device pin and use a quiet analog ground for the reference and supply-return connections. Place input and reference decoupling capacitors near the package, and route sensitive input traces away from digital clocks, switching-regulator nodes, and high-current return paths. This page combines the manufacturer part identity, package information, commercial listings, and comparison data for the INA110KUG4 with application guidance, layout cautions, and practical sourcing information. Review the complete manufacturer datasheet for the definitive pin configuration, electrical limits, gain equation, and recommended operating conditions before releasing a production design.

RFQ تماس
INA110SG - Fast-Settling FET-Input Amplifier | Texas Instruments
INA110SG

INA110SG - Fast-Settling FET-Input Amplifier | Texas Instruments

Texas Instruments INA110SG is a single-channel, monolithic FET-input instrumentation amplifier with a current-feedback topology, laser-trimmed input stage, internal gain-set resistors, and a 16-CDIP package. It supports gains of 1, 10, 100, 200, and 500 V/V, reaches 0.01% settling in 4 microseconds, and provides a typical bandwidth of 2.5 MHz. Maximum input bias current is 50 pA, while common-mode rejection reaches at least 106 dB at 10 kHz. An instrumentation amplifier is a specialized analog amplifier designed to amplify small differential signals while rejecting large common-mode voltages. Its internal architecture provides matched input devices, high input impedance, and stable gain behavior, making it part of the broader operational-amplifier and signal-conditioning hierarchy. INA110 applications include sensor-interface circuits, bridge amplifiers, current measurement, laboratory instrumentation, and multiplexed data-acquisition systems where low bias current, high common-mode rejection, and rapid settling are important. Internal gain resistors permit selectable gains of 1, 10, 100, 200, and 500 V/V without external feedback resistors. The laser-trimmed input stage supports high accuracy, with very low gain drift of up to 50 ppm per degree Celsius and input offset drift of 2 microvolts per degree Celsius. The low maximum bias current of 50 pA is particularly useful with high-impedance sources and electrostatic sensors. A minimum common-mode rejection of 106 dB at 10 kHz improves rejection of interference shared by both input terminals. The INA110 uses a current-feedback architecture rather than a conventional voltage-feedback topology. This architecture supports fast settling and broad usable bandwidth, while the 2.5 MHz typical bandwidth provides useful signal bandwidth for precision measurement systems. The manufacturer identifies fast settling as especially valuable in high-speed and multiplexed-input data-acquisition systems, where insufficient settling between channel selections can create measurement errors. The INA110SG operates from dual supplies with a typical total supply of plus or minus 15 V, a minimum of plus or minus 6 V, and a maximum of plus or minus 18 V. Typical applications include low-current sensor amplification, precision bridge excitation and readout, isolated or high-impedance measurement front ends, portable instrumentation, and multi-channel acquisition systems. The low bias current helps preserve sensor accuracy, while the 106 dB common-mode rejection helps suppress noise and power-supply-related disturbances appearing equally on both inputs. The 4-microsecond settling specification is valuable when many input channels must be sampled rapidly. Designers should verify supply polarity, common-mode range, gain selection, input protection, and output swing against the manufacturer datasheet before finalizing the analog path. Instrumentation-amplifier layouts should use short input traces, guard techniques for high-impedance nodes, and symmetric routing to minimize parasitic imbalance. Decoupling capacitors should be placed close to the supply pins, while unused gain-select pins must be connected according to the recommended configuration for the intended gain. This product overview combines the INA110SG architecture, verified performance characteristics, application guidance, package constraints, and drop-in alternatives into an engineering-focused reference. It also highlights the trade-offs involved when replacing a military-temperature ceramic CDIP with a lower-temperature plastic or ceramic DIP implementation.

RFQ تماس
INA111AP - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments
INA111AP

INA111AP - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA111AP is a high-speed, FET-input instrumentation amplifier with a gain range from 1 to over 1,000 V/V, 2 MHz bandwidth at a gain of 10, and an 8-pin plastic DIP package. It also provides a maximum input bias current of 20 pA, maximum input offset voltage of 500 µV, and minimum common-mode rejection of 106 dB. An instrumentation amplifier is a precision amplifier designed to amplify small differential signals while rejecting large common-mode voltages. Its internal differential amplifier stages provide accurate gain, high input impedance, and balanced inputs, making the category well suited to sensor bridges, strain gauges, biomedical instrumentation, and industrial measurement systems. Within the signal-chain hierarchy, the INA111AP belongs to the amplifier IC family and specifically serves as a differential instrumentation amplifier. A single external resistor sets the closed-loop gain, simplifying adjustment while preserving the performance of the internal current-feedback architecture. The gain can range from 1 to over 1,000 V/V, allowing the same device to amplify millivolt-level sensor outputs or larger instrumentation signals. Laser trimming supports low offset voltage, with a maximum of 500 µV, and maximum offset-voltage drift of 5 µV/°C. The current-feedback topology extends bandwidth to 2 MHz at a gain of 10 and provides a settling time of 4 µs to 0.01% at a gain of 100. These speed characteristics make the INA111AP suitable for measurement systems that need better transient response than conventional voltage-feedback instrumentation amplifiers, although bandwidth decreases as the selected gain increases. Typical applications include precision bridge excitation and readout, low-current sensor interfaces, laboratory instrumentation, diagnostic equipment, and industrial control systems. The wide supply range of 12 V to 36 V supports higher-voltage industrial systems, while the FET-input architecture minimizes input-bias-current error when measuring high-impedance sources. For reliable circuit implementation, place the gain-setting resistor close to the RG pins, provide stable input and output decoupling, and keep sensitive input traces away from high-current switching paths. Verify settling time and bandwidth at the actual selected gain because both performance characteristics depend on gain, supply voltage, and signal amplitude. This page combines manufacturer specifications, package and pin guidance, application engineering notes, and drop-in replacement analysis to support faster component selection and PCB implementation. It identifies where the INA111AP fits in measurement systems and clarifies the practical limits engineers should check before finalizing a precision signal chain.

RFQ تماس
INA111AU - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments
INA111AU

INA111AU - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA111AU is a high-speed FET-input instrumentation amplifier with 2 MHz bandwidth, 17 V/us slew rate, and a 16-pin SOIC package. It is designed for precision signal conditioning where low input bias current, high common-mode rejection, and fast settling are important. The device uses a current-feedback architecture and provides a gain range of 1 to 1000 through an external gain-setting resistor. An instrumentation amplifier is a differential analog amplifier designed for measuring small differential signals while rejecting large common-mode voltages. It is commonly used to amplify sensor outputs, bridge signals, strain-gauge outputs, and low-level biological signals. The INA111AU belongs to the instrumentation amplifier hierarchy, which provides differential input handling and gain control in a compact analog front end. The FET input stage reduces input bias current to 20 pA maximum, making the INA111AU suitable for high-impedance sources. Its maximum input offset voltage is 500 uV, and its maximum input offset voltage drift is 5 uV/C. The minimum common-mode rejection ratio is 106 dB. The device offers a 2 MHz bandwidth and 17 V/us slew rate, supporting faster response than many general-purpose precision instrumentation amplifiers. The INA111AU uses a three-operamplifier instrumentation-amplifier architecture with laser-trimmed resistors. A single external resistor sets the closed-loop gain, allowing gain values from 1 to 1000 when the specified gain-setting resistor is used. This combination of differential input, adjustable gain, and high input impedance makes the device suitable for conditioning signals from pressure, temperature, current, and resistive bridge sensors. Typical applications include bridge-transducer amplification, portable measurement systems, instrumentation interfaces, industrial sensor conditioning, and precision data-acquisition front ends. The low bias current helps preserve sensor-source accuracy, while the 106 dB minimum common-mode rejection helps suppress noise and supply disturbances that are common to both differential inputs. Designers should keep input and feedback traces short, provide suitable bypassing close to the power pins, and verify the external gain resistor against the datasheet gain equation. Input common-mode and output swing limits must be checked at the selected supply voltage and gain. The manufacturer datasheet should be used for the complete pin description, recommended application circuit, and gain-setting calculations. This product page combines the manufacturer specifications, verified sourcing information, package details, application guidance, and engineering-oriented design notes. It helps engineers evaluate the INA111AU for high-impedance measurement circuits while identifying the key electrical limits that determine signal fidelity and system compatibility.

RFQ تماس