Produits (44 000+)

THS6072ID - 175MHz Low-Power ADSL Receiver | TI
THS6072ID

THS6072ID - 175MHz Low-Power ADSL Receiver | TI

The Texas Instruments THS6072ID is a low-power ADSL differential receiver with 175 MHz bandwidth, 10 nV/√Hz voltage noise, and 3.4 mA per-channel quiescent current, housed in an 8-pin SOIC package. Designed for high-speed differential signal recovery, it targets central-office and remote-terminal ADSL equipment where bandwidth, low distortion, and reduced power consumption are important. An ADSL differential receiver is a voltage-feedback, high-speed analog interface circuit that converts a small differential input signal into a single-ended output suitable for processing by downstream circuitry. In the signal-chain hierarchy, it belongs to the receiver and operational-amplifier family within interface ICs, supporting the broader communications, networking, and data-processing systems used to transport high-frequency digital information over copper lines. Key characteristics include a 175 MHz -3 dB bandwidth, a 10 nV/√Hz voltage-noise density, and very low distortion of -79 dBc at 1 MHz with a 1 kΩ load. The 3.4 mA per-channel quiescent current supports low-power ADSL designs, while the wide bandwidth provides margin for high-speed data and test-and-measurement signal-chain applications. The operating temperature range is -40°C to +85°C, covering industrial-temperature applications. Technically, the THS6072 uses a voltage-feedback receiver architecture optimized for differential operation. Its low noise and low distortion make it suitable for amplifying small signals without adding excessive broadband noise or nonlinear products. Designers should still verify input common-mode range, output swing, supply voltage, gain configuration, stability, and external component requirements against the manufacturer datasheet before finalizing a production circuit. Typical applications include ADSL line-interface equipment, central-office termination electronics, remote-terminal units, high-speed communication receivers, broadband signal-conditioning modules, and instrumentation requiring a wide-band differential input stage. The 8-pin SOIC package also supports conventional PCB assembly, although high-speed layout and clean return paths remain important. The principal design consideration is signal integrity. Keep differential traces short, matched, and continuous over a common ground plane, place input and bypass components close to their pins, and control return currents. Verify that external compensation and gain settings preserve stability at the intended load and signal amplitude. This product page consolidates verified manufacturer and distributor information, supply data, technical characteristics, candidate drop-in alternatives, and practical interface-layout guidance to support faster component selection and PCB design.

Devis Contact
THS6092CD - 275mA +12V ADSL Driver | Texas Instruments
THS6092CD

THS6092CD - 275mA +12V ADSL Driver | Texas Instruments

The Texas Instruments THS6092CD is a dual high-speed operational amplifier configured as a 2/0 differential line driver for ADSL CPE and DSL applications. It supplies 275 mA of output current, operates from a single +12 V supply, and is packaged in an 8-pin SOIC. The device is intended for driving signals from a remote terminal toward the central office in asymmetrical digital subscriber line systems. An ADSL line driver is a specialized high-speed operational amplifier that delivers large current into a transformer-coupled or balanced line while maintaining low distortion and stable signal integrity. Within the power-management and signal-chain hierarchy, the THS6092 belongs to the operational-amplifier family, with applications in communications, networking, and broadband access equipment. The THS6092 family uses a +12 V supply and provides two output channels per package. According to the Texas Instruments THS6092 product page, the device is a 275 mA ADSL CPE and DSL line driver. Comparison information for the THS6092 identifies a supply current of 7.3 mA per channel and total harmonic distortion of -72 dBc while driving a 25-ohm load at 2 V peak-to-peak. These characteristics make the device appropriate for high-speed line-driving stages that require useful output swing, low distortion, and controlled supply consumption. The dual-channel architecture reduces the component count in broadband equipment by combining two line-driver channels in one package. Its 8-pin SOIC format supports conventional surface-mount assembly and simplifies inspection after soldering. The SOIC package also has a smaller body than larger power packages, although exposed-pad and heat-sink requirements must still be evaluated from the manufacturer's application guidance when operating continuously near the 275 mA output-current capability. Typical uses include ADSL customer-premises equipment, DSL line-interface cards, asymmetric digital subscriber line modems, and remote-terminal transmission stages. The same dual-channel topology can also serve other balanced, high-speed line interfaces when the signal amplitude, load, distortion, bandwidth, and supply requirements remain within the device's operating limits. Design the output return path and line interface carefully because the 275 mA output-current capability creates a meaningful load on the power supply and output network. Check transformer or termination-network behavior across the intended signal bandwidth, and use the manufacturer's recommended decoupling and layout practices to limit distortion and maintain high-frequency stability. This product page combines the exact manufacturer and distributor findings for the THS6092CD with package, application, sourcing, and drop-in comparison guidance. It also distinguishes electrically equivalent ordering options from genuine cross-package replacements so engineers can identify which components require a PCB redesign.

Devis Contact
THS6092ID - 275mA +12V ADSL CPE Line Driver | Texas Instruments
THS6092ID

THS6092ID - 275mA +12V ADSL CPE Line Driver | Texas Instruments

The Texas Instruments THS6092ID is a 275 mA, +12 V ADSL CPE and DSL line driver packaged in an 8-pin SOIC (D). It provides a high-speed dual-channel output stage for driving signals between the remote terminal and the central office, with a specified low total harmonic distortion of -72 dBc into a 25 Ω load at 2 Vpp. The device is intended for asymmetrical digital subscriber line equipment and other high-speed line-driver applications. An ADSL line driver is an interface IC that converts upstream and downstream data signals into high-amplitude voltage waveforms suitable for transmission over twisted-pair telephone lines. Within the broader signal-chain hierarchy, the THS6092 belongs to the line-driver and transceiver class of interface ICs, which connects digital data-processing equipment to physical communication media. Its dual-channel architecture supports two independently driven line outputs while simplifying the analog output stage of a customer-premises equipment design. Key features include operation from a single +12 V supply, supply current of 7.3 mA per channel, and 275 mA output-current capability. The device can produce an output swing of 18.4 Vpp, while its -72 dBc distortion at 2 Vpp into a 25 Ω load provides a meaningful margin for reducing nonlinear harmonics. The industrial temperature option covers -40 °C to +85 °C, supporting telecommunications equipment expected to operate across extended environmental conditions. Technically, the THS6092 combines high-speed amplification with a high-current output stage suitable for driving capacitive and resistive line loads. The 275 mA rating identifies the output-current capability rather than the 7.3 mA quiescent supply consumption, so engineers should evaluate both values separately. Its specified distortion behavior is especially relevant where signal fidelity must remain controlled through a long copper pair and an external transformer or protection network. Typical applications include ADSL customer-premises equipment, DSL line-interface cards, central-office line-driver modules, and other telecommunications equipment requiring high-voltage, high-current outputs. The integrated dual-driver arrangement reduces the number of separate output stages while supporting the voltage and current levels expected in line-driving circuits. A critical design consideration is the distinction between the THS6092 and THS6093 versions. Confirm the required channel polarity and control configuration against the exact data sheet before substitution. Also account for transformer turns ratio, line impedance, protection components, output waveform limits, and thermal dissipation when defining the external drive network. This page consolidates manufacturer specifications, package details, lifecycle-oriented ordering information, verified source links, and same-family replacement guidance. It also highlights the engineering parameters that should be checked before treating another THS6092-family device as a drop-in choice.

Devis Contact
THS6093CD - 275mA +12V ADSL Line Driver | Texas Instruments
THS6093CD

THS6093CD - 275mA +12V ADSL Line Driver | Texas Instruments

The Texas Instruments THS6093CD is a 275 mA, +12 V ADSL CPE and PLC line driver with shutdown, packaged in a 14-pin SOIC. It is designed for high-speed line-driving applications using either a 1:2 transformer ratio or single-supply operation. Its headline characteristics are 275 mA output current, +12 V supply operation, a 14-SOIC package, low 2.1 pA/√Hz noninverting current noise, and a shutdown function. An ADSL line driver is an interface integrated circuit that converts upstream data signals into suitable current and voltage levels for transmission over copper lines. It belongs to the interface IC hierarchy within integrated circuits and semiconductor signal-conditioning devices. The THS6093 is intended for full-rate ADSL and G.Lite equipment, including customer-premises equipment and power-line communication equipment where the line interface must combine high output current with controlled noise. Key features include compatibility with a 1:2 transformer ratio, a wide supply-voltage range, and suitability for single +12 V operation. The 275 mA output capability provides useful drive current for line termination and transformer coupling. The device also includes shutdown control, allowing a system to disable the driver when line transmission is not required. Low noninverting current noise of 2.1 pA/√Hz helps reduce noise coupled through a telephone hybrid into the downstream receiver path. The THS6093 uses a high-current output stage suited to the demanding load presented by an ADSL line interface. Its architecture supports both transformer-coupled and single-supply arrangements, giving designers flexibility in line-network topology. The 14-pin SOIC package is a conventional surface-mount format suitable for automated PCB assembly, although the high-current output path requires careful routing, thermal review, and adequate copper around the power and ground pins. Typical uses include ADSL CPE line interfaces, full-rate ADSL modems, G.Lite access equipment, PLC gateways, and communications terminals connected to copper lines. It is particularly relevant when the design needs a dedicated line driver with a shutdown control and operation from a +12 V supply rather than a general-purpose low-power amplifier. For PCB implementation, place the device close to the line-transformancer or network interface and keep the high-current output path compact. Use a low-inductance supply connection and adequate input and output bypassing according to the manufacturer application guidance. Verify maximum output current, voltage, and thermal conditions across temperature because 275 mA describes the line-driver capability rather than unlimited continuous load capacity. This product record combines the manufacturer identification, package information, current capability, major ADSL and PLC use cases, and practical implementation considerations. It also provides sourcing guidance for the exact THS6093CD ordering code and distinguishes confirmed specifications from parameters that still require confirmation from the manufacturer datasheet.

Devis Contact
THS6093ID - 275mA +12V ADSL Line Driver | Texas Instruments
THS6093ID

THS6093ID - 275mA +12V ADSL Line Driver | Texas Instruments

Texas Instruments THS6093ID is a dual-channel, high-speed ADSL CPE line driver rated for 275 mA output current and +12 V operation in a 14-pin SOIC package. The device is intended for driving signals from the remote terminal toward the central office in asymmetric digital subscriber line systems, including full-rate ADSL and G.Lite configurations. An ADSL line driver is a specialized interface-circuit component that converts upstream driver signals into robust, high-current line outputs suitable for copper telephone networks. It sits within the power-management and signal-conditioning hierarchy of a customer premises equipment design, translating logic-level commands into line-side waveforms while helping preserve signal integrity across the transformer-coupled network. Key features include a wide supply-voltage range, suitability for single +12 V operation, compatibility with a 1:2 transformer ratio, and low 2.1 pA/√Hz noninverting current noise. The THS6093 also provides low total harmonic distortion of -72 dBc while driving the line and includes shutdown control. Each channel draws only 7.3 mA of supply current, helping limit the power burden of a multi-output access circuit. The device uses two noninverting outputs in a 14-pin SOIC package. Its high output-current capability is important for ADSL line interfaces because the external transformer, network loading, and cable losses can require substantially more current than a conventional logic driver. The specified 275 mA rating provides the core design limit for transformer selection, copper-line loading, supply capability, and thermal analysis. Typical uses include full-rate ADSL customer premises equipment, G.Lite ADSL line interfaces, and power-line carrier line-driver circuits. In each application, the THS6093 can operate from a single +12 V rail and drive the line through an appropriate external transformer while the shutdown function provides a controlled path for reducing activity when the endpoint is inactive. The primary design consideration is ensuring that the +12 V supply, output-current demand, transformer ratio, load, thermal conditions, and signal-integrity expectations all agree. Use the manufacturer datasheet pin-description table when assigning PCB nets, and confirm that the selected transformer supports the specified 1:2 ratio and operating bandwidth.

Devis Contact
THS6182D - Low-Power ADSL/PLC Differential Driver | TI
THS6182D

THS6182D - Low-Power ADSL/PLC Differential Driver | TI

The Texas Instruments THS6182D is a low-power current-feedback differential line driver designed for full-rate ADSL and power-line communication systems. It delivers a 44 Vpp differential output swing, operates from dual supply rails, and is offered in a 16-pin SOIC package. The device includes selectable full, mid, low, and shutdown bias modes to balance output drive against power consumption. A line driver is an analog output interface that converts upstream signal information into a high-voltage differential signal capable of traversing copper, telephone, or other communications lines. The THS6182 belongs to the current-feedback operational-amplifier family and is positioned between a communications signal source and the physical line. Its differential architecture reduces susceptibility to common-mode noise while providing the voltage swing and current-drive capability needed by xDSL line cards. Key features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer identifies low distortion, low inverting current noise, and stable operation at low channel current as important benefits for receiver sensitivity and central-office line-card density. An IADJ pin also provides user-controlled bias current for system-level optimization. According to the manufacturer product page, the THS6182 is pin compatible with EL1503C and EL1508C line-driver families and is available in multiple packages and power-control modes. Its current-feedback differential architecture is intended to preserve signal integrity while minimizing dissipation, making it particularly relevant to high-density ADSL central-office equipment and PLC systems. The advertised 3.2 nV/√Hz inverting current noise supports receiver-sensitive signal paths. Typical deployments include full-rate ADSL central-office line cards, DSL access multiplexor equipment, remote terminal equipment, and PLC transmitters. In these systems, the driver accepts an upstream differential signal and produces a substantially larger differential output across the line interface. Designers must preserve the intended differential topology, provide suitable bypass capacitance, terminate unused inputs correctly, and verify thermal performance across the required line swing and channel-current range. A key design consideration is power mode selection. Full-bias mode provides maximum drive when required, while mid- and low-bias modes reduce dissipation when channel current and reach requirements permit. The shutdown state provides the lowest listed current, but enabling and disabling channels must be coordinated with the communication protocol to avoid invalid transmitted states. This page combines verified manufacturer and distributor information with application guidance; it does not infer unprovided electrical limits or invent replacement parts.

Devis Contact
THS6182DR - Low-Power ADSL/PLC Differential Driver | TI (Tape & Reel)
THS6182DR

THS6182DR - Low-Power ADSL/PLC Differential Driver | TI (Tape & Reel)

The Texas Instruments THS6182DR is a low-power current-feedback differential line driver designed for full-rate ADSL and power-line communication systems. It delivers a 44 Vpp differential output swing, operates from dual supply rails, and is offered in a 16-pin SOIC package. The device includes selectable full, mid, low, and shutdown bias modes to balance output drive against power consumption. A line driver is an analog output interface that converts upstream signal information into a high-voltage differential signal capable of traversing copper, telephone, or other communications lines. The THS6182 belongs to the current-feedback operational-amplifier family and is positioned between a communications signal source and the physical line. Its differential architecture reduces susceptibility to common-mode noise while providing the voltage swing and current-drive capability needed by xDSL line cards. Key features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer identifies low distortion, low inverting current noise, and stable operation at low channel current as important benefits for receiver sensitivity and central-office line-card density. An IADJ pin also provides user-controlled bias current for system-level optimization. According to the manufacturer product page, the THS6182 is pin compatible with EL1503C and EL1508C line-driver families and is available in multiple packages and power-control modes. Its current-feedback differential architecture is intended to preserve signal integrity while minimizing dissipation, making it particularly relevant to high-density ADSL central-office equipment and PLC systems. The advertised 3.2 nV/√Hz inverting current noise supports receiver-sensitive signal paths. Typical deployments include full-rate ADSL central-office line cards, DSL access multiplexor equipment, remote terminal equipment, and PLC transmitters. In these systems, the driver accepts an upstream differential signal and produces a substantially larger differential output across the line interface. Designers must preserve the intended differential topology, provide suitable bypass capacitance, terminate unused inputs correctly, and verify thermal performance across the required line swing and channel-current range. A key design consideration is power mode selection. Full-bias mode provides maximum drive when required, while mid- and low-bias modes reduce dissipation when channel current and reach requirements permit. The shutdown state provides the lowest listed current, but enabling and disabling channels must be coordinated with the communication protocol to avoid invalid transmitted states. This page combines verified manufacturer and distributor information with application guidance; it does not infer unprovided electrical limits or invent replacement parts.

Devis Contact
THS6182DW - Low-Power ADSL/PLC Line Driver | Texas Instruments
THS6182DW

THS6182DW - Low-Power ADSL/PLC Line Driver | Texas Instruments

The Texas Instruments THS6182DW is a low-power differential line driver designed for full-rate ADSL and power-line communication systems, with a 20-pin SOIC package. It uses current-feedback architecture, provides selectable operating-current modes, and supports an adjustable bias-current input. The device is specified for 1/0 DSL line-driving duties over a temperature range of -40°C to +85°C. An ADSL line driver is a specialized interface-circuit component that converts upstream data into a high-current differential signal suitable for transmission over copper telephone lines. This device belongs to the interface IC hierarchy: line driver → differential transceiver → communications interface → semiconductor. Unlike a general-purpose voltage-output amplifier, a current-feedback line driver combines high-frequency signal capability with output-current control designed specifically for line networks. Key operating features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer also identifies operation down to 1.8 mA per channel, an adjustable-current input, and a low-noise result of 3.2 nV/√Hz inverting current noise. These selectable modes allow designers to balance transmission performance against power dissipation. The current-feedback differential architecture supports full-rate ADSL applications while maintaining high linearity without the complexity and power burden of conventional designs. The adjustable bias input lets the circuit user control the operating-current condition, making it useful in designs where line length, transformer characteristics, aggregate line load, or central-office power density affect the preferred drive level. The THS6182 is also identified as pin-compatible with the EL1503C and EL1508C. Typical uses include ADSL central-office line-card equipment, DSL access concentrators, splitters, remote-terminal and line-unit equipment, and PLC interface circuits. The device is particularly relevant where multiple line channels share a constrained power budget, because its low-bias and shutdown modes reduce dissipation when channel activity is low or a port must be disabled. The primary design trade-off is current setting versus signal performance and power consumption. Select full-bias operation for maximum line drive, lower modes for reduced dissipation, and shutdown when the port is inactive. Place the device and its associated line-network components carefully because long high-current transmission paths can introduce impedance discontinuities and signal-integrity problems that are not corrected by changing bias mode. This product page combines the manufacturer’s functional description, operating-mode data, package information, interface use cases, and replacement guidance with practical selection notes. It also highlights the distinction between electrically equivalent order codes and genuinely pin-compatible drop-in choices, helping engineers assess whether a redesign or package-level substitution is actually required.

Devis Contact
THS6212YS - Broadband PLC Line Driver | Texas Instruments
THS6212YS

THS6212YS - Broadband PLC Line Driver | Texas Instruments

Texas Instruments THS6212YS is a high-speed, differential broadband PLC/HPLC line-driver amplifier based on current-feedback architecture, with support for line power up to 14.5 dBm at frequencies through 30 MHz. The device is supplied in a 17-terminal, rectangular, no-lead die package. Its differential output topology is intended for power-line communication systems that require broadband signal transmission through challenging in-home or outdoor network wiring. A broadband PLC line driver is an interface amplifier that generates a differential signal for transmission over power-line communication wiring. The THS6212 belongs to the line-driver and receiver hierarchy of interface ICs, where its current-feedback amplifier architecture provides the active gain stage needed to drive external circuitry and realize a physical-layer transmitter signal. This makes it relevant to broadband PLC modems, HPLC endpoints, carrier communication equipment, and line-coupling networks. The manufacturer identifies current-feedback architecture, differential operation, transmission capability through 30 MHz, and line power up to 14.5 dBm as the principal characteristics of the THS6212. Differential drive helps reject common-mode disturbances picked up from the shared power-line environment. The broad operating bandwidth supports both low-frequency carrier data and substantially higher-frequency communication signals, while the 28 V maximum supply rating provides headroom for an industrial interface stage. The target is identified as an industrial-temperature device operating from -40 °C to +85 °C. Its 17-terminal no-lead package is intended for surface-mount assembly. Because this ordering code is associated with a die rather than a conventional leaded or molded IC package, PCB land-pattern design, exposed-pad treatment, assembly profile, and reflow requirements must be confirmed against the official package drawing before layout release. Typical uses include broadband PLC transmitters, HPLC communication endpoints, carrier-current networking equipment, and line-driver stages for communications over existing electrical infrastructure. In a transmitter implementation, the amplifier output is connected through the appropriate line-coupling and filtering network. Component values and protection requirements depend on the transformer, line impedance, conducted-emissions target, and safety arrangement of the complete communication equipment. Design should preserve the high-speed current-feedback path with short traces, carefully controlled return current, and decoupling placed close to the supply pins. Output isolation, impedance matching, and surge protection must be evaluated together because a line driver also sees the external network's distributed and transient behavior. The amplifier rating does not remove the need for application-level isolation and protection. This page consolidates the manufacturer's device description, electrical and environmental limits, sourcing structure, and engineering guidance. It also distinguishes verified device facts from parameters that require the official datasheet or package drawing, helping designers establish whether the THS6212YS fits a broadband PLC signal chain before committing the layout.

Devis Contact
THS7303PW - 3-Channel Low-Power Video Amplifier | TI
THS7303PW

THS7303PW - 3-Channel Low-Power Video Amplifier | TI

The Texas Instruments THS7303PW is a three-channel, low-power video amplifier with I2C control, selectable filters, 6 dB gain, SAG correction, a 2:1 input multiplexer, and selectable input bias modes. It operates from a single 2.7 V to 5 V supply and is packaged in a 20-pin TSSOP (PW). The device also features a 190 MHz bandwidth and a 320 V/µs slew rate, making it suited to high-speed video signal processing. A video amplifier is an analog signal-conditioning IC that increases the amplitude and drive capability of composite, component, or other video signals. It belongs to the broader hierarchy of amplifier ICs, analog integrated circuits, and signal-chain semiconductors. The THS7303PW combines three buffered video channels with programmable control, allowing a compact design to select filtering, gain, multiplexer routing, and bias behavior without replacing multiple fixed-function devices. Its principal features include three integrated video amplifiers, a 2:1 input multiplexer, a selectable 6 dB gain setting, selectable low-pass filters, SAG correction, and an I2C interface. These functions support programmable video paths in set-top boxes, video processors, display equipment, surveillance systems, and general-purpose analog-to-digital signal-processing circuits. Low power consumption is particularly useful when three active video channels must operate continuously in compact commercial or industrial equipment. The THS7303PW uses a complementary silicon-germanium BiCom-III process according to the manufacturer documentation. Its approximately 190 MHz small-signal bandwidth and 320 V/µs slew rate provide ample speed for high-frequency video signals. The 2.1:1 power-supply current and 6 mA quiescent current reported in the device documentation describe a low-power design intended to balance drive strength, integration, and heat management in a surface-mount package. Typical uses include conditioning composite video for digitization, buffering multiple video outputs, switching between two input sources with a 2:1 multiplexer, and applying programmable filter or gain settings in display and broadcast equipment. The I2C control interface also enables software-controlled configuration of multiple channels in systems where the video path changes during operation. PCB design should preserve the short, controlled return paths needed by high-speed analog signals. Place input and output bypass capacitors close to the relevant supply and ground pins, keep video traces away from switching nodes and digital control lines, and follow the pin descriptions and layout guidance in the manufacturer datasheet. Bus pull-up resistors and series damping should be selected to keep SCL and SDA waveforms within valid limits. This page organizes the THS7303PW’s functions, pin-compatible replacement information, comparison parameters, application guidance, and practical design considerations. It supports faster component evaluation by placing the device’s key architectural features alongside the engineering checks required for reliable video-signal implementation.

Devis Contact
THS7313PW - 3-Channel 6dB SDTV Video Amp | Texas Instruments
THS7313PW

THS7313PW - 3-Channel 6dB SDTV Video Amp | Texas Instruments

The Texas Instruments THS7313PW is a three-channel, low-power SDTV video amplifier with I2C control, selectable 6 dB gain, sag correction, 2:1 input multiplexing, and selectable input-bias modes. The device operates from a single 2.7 V to 5 V supply and is packaged in a 20-pin TSSOP (PW) package. It combines three video processing channels with digital configuration in one low-power integrated circuit. A video amplifier conditions analog composite video signals by providing gain, impedance buffering, bias control, and correction functions before the signal reaches an encoder, display interface, or video capture stage. The THS7313 belongs to the video-amplifier hierarchy within interface ICs and is intended for SDTV and related composite-video signal paths requiring controlled amplitude and multiple source selection. The principal features are three integrated video channels, 6 dB gain, 2:1 input multiplexing, sag correction, I2C-controlled configuration, and selectable input-bias modes. The 2:1 multiplexer allows each channel to select between two video inputs, reducing the number of external routing components when the source changes infrequently. I2C control supports programmable configuration while avoiding dedicated control pins for every parameter. The device is fabricated using Texas Instruments' complementary silicon-germanium BiCom-III process. This process supports the integration of high-speed analog video functions, low-power operation, and digital control in one monolithic device. Single-supply operation also simplifies PCB power planning in portable and space-constrained consumer equipment. Typical uses include SDTV set-top boxes, video scalers, digital video recorders, television sets, video game consoles, and other systems that process composite video. The three-channel architecture suits designs carrying red, green, and blue component signals or three separate composite-video channels. The integrated multiplexer is especially useful when each channel must accept one of two source signals. Designers should preserve the recommended input and output network, provide a stable low-noise supply, and verify I2C address and configuration settings before enabling signal routing. Because no complete pin-description table is reproduced here, use the manufacturer datasheet pin table and typical-application circuit when assigning tracks, terminating inputs, and placing bypass capacitors. This page consolidates the device identity, package information, verified commercial listing, candidate drop-in relationships, application guidance, and engineering considerations into a practical reference for evaluating the THS7313PW.

Devis Contact
THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7314D

THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments

The Texas Instruments THS7314D is a 3-channel SDTV video amplifier with integrated fifth-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and combines three video channels in one package. According to the Texas Instruments product and data-sheet information, the device uses the Silicon-Germanium BiCom-III process and consumes 16 mA total quiescent current at 3.3 V. A video amplifier is an analog signal-chain component that conditions composite or component video signals between a source, processing stage, and display. It belongs to the amplifier hierarchy, specifically the video-amplifier and video-buffer category. Unlike a passive termination network, an integrated video amplifier can provide filtering, gain, impedance matching, and output-drive capability while reducing the number of discrete components required on a video board. The THS7314D provides three buffered channels, 6 dB gain, and fifth-order filtering in one 8-pin SOIC. Its rail-to-rail output stage supports both AC and DC line-driving requirements. The manufacturer specifically identifies driving two lines or 75-ohm loads as supported use cases, making the device relevant to SDTV routing, video distribution, and display-adapter designs. The integrated filter function is especially useful when system designers want repeatable channel filtering without external filter networks. Its low-power operation distinguishes the part from higher-current video drivers. Texas Instruments states that the total 16 mA quiescent current at a 3.3 V supply makes the THS7314 suitable for USB-powered, portable, and other power-sensitive video applications. The single-supply 3 V to 5 V operating range also allows the same architecture to operate from nominal 3.3 V and 5 V system rails, although the complete design must satisfy the limits in the manufacturer data sheet for each voltage and temperature condition. Typical applications include SDTV output buffering, video splitters and distribution boards, portable media equipment, video capture equipment, and display interfaces. In each case, the three-channel structure reduces routing complexity while the fifth-order filters and 6 dB gain support controlled signal transmission into downstream analog video stages. The 75-ohm drive capability is useful when the output must connect through conventional video cabling to a terminated load. Designers should verify the complete pin configuration, decoupling requirements, input and output impedance, bandwidth, channel-to-channel behavior, and recommended termination network against the official data sheet. Video-layout practices should also be considered, including short trace routing, careful grounding, separation between analog video paths and noisy switching circuitry, and appropriate filtering at external connectors. This page consolidates the verified manufacturer and distributor information for THS7314D and clearly identifies parameters for which verified values were not supplied. It also distinguishes the confirmed device characteristics from engineering information that must be obtained from the official THS7314 data sheet before layout or qualification decisions are finalized.

Devis Contact
THS7314DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7314DR

THS7314DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments THS7314DR is a 3-channel SDTV video amplifier with integrated fifth-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and combines three video channels in one package. According to the Texas Instruments product and data-sheet information, the device uses the Silicon-Germanium BiCom-III process and consumes 16 mA total quiescent current at 3.3 V. A video amplifier is an analog signal-chain component that conditions composite or component video signals between a source, processing stage, and display. It belongs to the amplifier hierarchy, specifically the video-amplifier and video-buffer category. Unlike a passive termination network, an integrated video amplifier can provide filtering, gain, impedance matching, and output-drive capability while reducing the number of discrete components required on a video board. The THS7314DR provides three buffered channels, 6 dB gain, and fifth-order filtering in one 8-pin SOIC. Its rail-to-rail output stage supports both AC and DC line-driving requirements. The manufacturer specifically identifies driving two lines or 75-ohm loads as supported use cases, making the device relevant to SDTV routing, video distribution, and display-adapter designs. The integrated filter function is especially useful when system designers want repeatable channel filtering without external filter networks. Its low-power operation distinguishes the part from higher-current video drivers. Texas Instruments states that the total 16 mA quiescent current at a 3.3 V supply makes the THS7314 suitable for USB-powered, portable, and other power-sensitive video applications. The single-supply 3 V to 5 V operating range also allows the same architecture to operate from nominal 3.3 V and 5 V system rails, although the complete design must satisfy the limits in the manufacturer data sheet for each voltage and temperature condition. Typical applications include SDTV output buffering, video splitters and distribution boards, portable media equipment, video capture equipment, and display interfaces. In each case, the three-channel structure reduces routing complexity while the fifth-order filters and 6 dB gain support controlled signal transmission into downstream analog video stages. The 75-ohm drive capability is useful when the output must connect through conventional video cabling to a terminated load. Designers should verify the complete pin configuration, decoupling requirements, input and output impedance, bandwidth, channel-to-channel behavior, and recommended termination network against the official data sheet. Video-layout practices should also be considered, including short trace routing, careful grounding, separation between analog video paths and noisy switching circuitry, and appropriate filtering at external connectors. This page consolidates the verified manufacturer and distributor information for THS7314DR and clearly identifies parameters for which verified values were not supplied. It also distinguishes the confirmed device characteristics from engineering information that must be obtained from the official THS7314 data sheet before layout or qualification decisions are finalized.

Devis Contact
THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7315D

THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments

Texas Instruments THS7315D is a three-channel SDTV video amplifier with integrated fifth-order filters and 5.2 V/V gain, operating from a single 3 V to 5 V supply in an 8-SOIC package. The device combines three video channels, fixed 5.2 V/V gain, and fifth-order filtering for CVBS, S-Video, YPBPR 480i/576i, YUV, and GBR/RGB signal paths. A video amplifier is an analog signal-conditioning IC that increases the amplitude of composite or component video signals while controlling bandwidth, attenuation, and unwanted spectral content. Within the broader semiconductor hierarchy, the THS7315D is a video amplifier, a type of analog amplifier, and ultimately an integrated circuit used within display, broadcast, set-top-box, and video-conversion systems. The THS7315D integrates three independent SDTV video amplifier channels and fifth-order filters into one package. Its fixed gain of 5.2 V/V is useful when a source produces a relatively small video amplitude and the downstream circuitry requires additional signal swing. The fifth-order filters provide frequency-dependent noise and interference attenuation, while the single-supply architecture simplifies power planning in 3 V and 5 V systems. Texas Instruments fabricated the device using its complementary silicon-germanium BiCom3 process. This integration reduces the number of discrete amplification and filtering stages required in a multi-channel analog video path. Because the amplifier includes filters rather than functioning only as a wideband buffer, board-level signal integrity depends on correct source and load impedances, adequate bypass capacitance, short output routing, and proper grounding. The supplied data does not provide detailed output impedance, bandwidth, settling-time, noise, or stability-versus-capacitance figures, so those characteristics must be confirmed in the manufacturer datasheet before final circuit sign-off. Typical uses include SDTV video buffering, Y/Cb/Cr component-video distribution, CVBS and S-Video processing, RGB amplification, and DAC reconstruction filtering. The integrated three-channel arrangement is particularly useful when red, green, and blue or Y, Pb, and Pr channels must receive matched amplification and filtering. It can also support protected or industrial video equipment where reducing the number of active stages simplifies signal routing and maintenance. A primary design consideration is ensuring that the source impedance, termination, and downstream load remain compatible with the integrated filter network. The manufacturer's datasheet and typical application information should be used to select input and output coupling or termination components. PCB layout should keep the device and its bypass capacitors close together, maintain short analog traces, provide an uninterrupted ground reference, and isolate sensitive video paths from switching and high-current return paths. This product page consolidates the verified manufacturer and distributor information, distinguishes documented THS7315D characteristics from missing technical data, identifies verified same-package replacements, and adds practical application and layout guidance for engineers evaluating the THS7315D in SDTV video signal chains.

Devis Contact
THS7315DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7315DR

THS7315DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments THS7315DR is a three-channel SDTV video amplifier with integrated fifth-order filters and 5.2 V/V gain, operating from a single 3 V to 5 V supply in an 8-SOIC package. The device combines three video channels, fixed 5.2 V/V gain, and fifth-order filtering for CVBS, S-Video, YPBPR 480i/576i, YUV, and GBR/RGB signal paths. A video amplifier is an analog signal-conditioning IC that increases the amplitude of composite or component video signals while controlling bandwidth, attenuation, and unwanted spectral content. Within the broader semiconductor hierarchy, the THS7315DR is a video amplifier, a type of analog amplifier, and ultimately an integrated circuit used within display, broadcast, set-top-box, and video-conversion systems. The THS7315DR integrates three independent SDTV video amplifier channels and fifth-order filters into one package. Its fixed gain of 5.2 V/V is useful when a source produces a relatively small video amplitude and the downstream circuitry requires additional signal swing. The fifth-order filters provide frequency-dependent noise and interference attenuation, while the single-supply architecture simplifies power planning in 3 V and 5 V systems. Texas Instruments fabricated the device using its complementary silicon-germanium BiCom3 process. This integration reduces the number of discrete amplification and filtering stages required in a multi-channel analog video path. Because the amplifier includes filters rather than functioning only as a wideband buffer, board-level signal integrity depends on correct source and load impedances, adequate bypass capacitance, short output routing, and proper grounding. The supplied data does not provide detailed output impedance, bandwidth, settling-time, noise, or stability-versus-capacitance figures, so those characteristics must be confirmed in the manufacturer datasheet before final circuit sign-off. Typical uses include SDTV video buffering, Y/Cb/Cr component-video distribution, CVBS and S-Video processing, RGB amplification, and DAC reconstruction filtering. The integrated three-channel arrangement is particularly useful when red, green, and blue or Y, Pb, and Pr channels must receive matched amplification and filtering. It can also support protected or industrial video equipment where reducing the number of active stages simplifies signal routing and maintenance. A primary design consideration is ensuring that the source impedance, termination, and downstream load remain compatible with the integrated filter network. The manufacturer's datasheet and typical application information should be used to select input and output coupling or termination components. PCB layout should keep the device and its bypass capacitors close together, maintain short analog traces, provide an uninterrupted ground reference, and isolate sensitive video paths from switching and high-current return paths. This product page consolidates the verified manufacturer and distributor information, distinguishes documented THS7315DR characteristics from missing technical data, identifies verified same-package replacements, and adds practical application and layout guidance for engineers evaluating the THS7315DR in SDTV video signal chains.

Devis Contact
THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments
THS7316D

THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments

Texas Instruments THS7316D is a 3-channel HDTV video amplifier with integrated 5th-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and provides three buffered video channels for HDTV and related video-signal processing systems. The device is fabricated using the Silicon-Germanium (SiGe) BiCom-III process and is designed for low-power video applications where integrated filtering reduces external circuit complexity. A video amplifier is a specialized analog amplifier that buffers and conditions composite or component video signals while preserving usable bandwidth and signal amplitude. The THS7316 belongs to the broader video-amplifier and signal-conditioning category, integrating three amplifier channels with fixed filtering into one device. This makes it useful in set-top boxes, television equipment, video processors, projectors, displays, and other systems that distribute or convert analog video signals. The principal features of the THS7316D are its three-channel architecture, 6 dB voltage gain, 5th-order integrated filters, single-supply operation, and 43 MHz video bandwidth identified in the verified product data. The filter implementation helps remove unwanted high-frequency video components before they reach downstream circuitry. Its three-channel arrangement allows red, green, and blue video paths to be amplified consistently within one package, reducing the number of separate buffer devices required. The device uses a low-power SiGe BiCom-III process and is intended for 3 V to 5 V single-supply systems. The verified distributor description identifies the THS7316 as a 3-channel integrated video buffer, while the Texas Instruments product page identifies the 5th-order filter and 6 dB gain functions. The 8-SOIC package is compatible with conventional surface-mount assembly and is suitable for compact consumer and industrial video equipment. Typical applications include HDTV signal conditioning, RGB video distribution, video projection systems, television receivers, set-top-box video outputs, and industrial video interfaces. The integrated filtering is particularly useful where the source signal requires predictable bandwidth limiting before a display, encoder, scaler, or analog-to-digital conversion stage. The fixed 6 dB gain also provides a defined signal-conditioning function rather than requiring an external gain network for basic video buffering. Designers should verify the complete electrical limits, decoupling requirements, output loading, and filter response in the manufacturer datasheet before layout release. Pay particular attention to the single-supply input range, required bypass capacitors, and the acceptable input and output signal levels. Because the available verified data does not provide the complete pin mapping or all parameter values, the PCB footprint and analog signal path should be checked against the official THS7316 documentation rather than inferred from distributor descriptions. This page combines verified manufacturer and distributor information, source-backed technical context, and practical selection considerations for engineers evaluating the THS7316D. It also distinguishes verified attributes from parameters that remain to be confirmed in the datasheet, helping prevent assumptions about gain, bandwidth, filtering, or pin compatibility during component selection.

Devis Contact
THS7316DR - 3-Channel HDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7316DR

THS7316DR - 3-Channel HDTV Video Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments THS7316DR is a 3-channel HDTV video amplifier with integrated 5th-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and provides three buffered video channels for HDTV and related video-signal processing systems. The device is fabricated using the Silicon-Germanium (SiGe) BiCom-III process and is designed for low-power video applications where integrated filtering reduces external circuit complexity. A video amplifier is a specialized analog amplifier that buffers and conditions composite or component video signals while preserving usable bandwidth and signal amplitude. The THS7316 belongs to the broader video-amplifier and signal-conditioning category, integrating three amplifier channels with fixed filtering into one device. This makes it useful in set-top boxes, television equipment, video processors, projectors, displays, and other systems that distribute or convert analog video signals. The principal features of the THS7316DR are its three-channel architecture, 6 dB voltage gain, 5th-order integrated filters, single-supply operation, and 43 MHz video bandwidth identified in the verified product data. The filter implementation helps remove unwanted high-frequency video components before they reach downstream circuitry. Its three-channel arrangement allows red, green, and blue video paths to be amplified consistently within one package, reducing the number of separate buffer devices required. The device uses a low-power SiGe BiCom-III process and is intended for 3 V to 5 V single-supply systems. The verified distributor description identifies the THS7316 as a 3-channel integrated video buffer, while the Texas Instruments product page identifies the 5th-order filter and 6 dB gain functions. The 8-SOIC package is compatible with conventional surface-mount assembly and is suitable for compact consumer and industrial video equipment. Typical applications include HDTV signal conditioning, RGB video distribution, video projection systems, television receivers, set-top-box video outputs, and industrial video interfaces. The integrated filtering is particularly useful where the source signal requires predictable bandwidth limiting before a display, encoder, scaler, or analog-to-digital conversion stage. The fixed 6 dB gain also provides a defined signal-conditioning function rather than requiring an external gain network for basic video buffering. Designers should verify the complete electrical limits, decoupling requirements, output loading, and filter response in the manufacturer datasheet before layout release. Pay particular attention to the single-supply input range, required bypass capacitors, and the acceptable input and output signal levels. Because the available verified data does not provide the complete pin mapping or all parameter values, the PCB footprint and analog signal path should be checked against the official THS7316 documentation rather than inferred from distributor descriptions. This page combines verified manufacturer and distributor information, source-backed technical context, and practical selection considerations for engineers evaluating the THS7316DR. It also distinguishes verified attributes from parameters that remain to be confirmed in the datasheet, helping prevent assumptions about gain, bandwidth, filtering, or pin compatibility during component selection.

Devis Contact
THS7353PW - 3-Channel I2C Video Amp | Texas Instruments
THS7353PW

THS7353PW - 3-Channel I2C Video Amp | Texas Instruments

Texas Instruments THS7353PW is a three-channel, low-power video amplifier with I2C control, selectable filters, 0 dB gain, and a 2:1 input multiplexer in a 20-pin TSSOP (PW) package. It operates from a single 2.7 V to 5 V supply and consumes 16.2 mA total quiescent current at a 3.3 V supply. A video amplifier, also called a video buffer, conditions analog video signals between source and destination stages. The THS7353 belongs to the broader integrated video-amplifier hierarchy, combining signal buffering, gain control, filtering, input selection, and serial configuration in one semiconductor. This integration reduces the number of discrete signal-path components while allowing programmable behavior through an I2C interface. The device provides three video channels, a selectable 2:1 multiplexer, selectable low-pass or bypass filter configurations, and programmable 0 dB gain. Its low-power design and single-supply operation suit portable equipment, including USB-powered systems, as well as HDTV, PVR, DVDR, projector, and general-purpose video equipment. An operating-temperature range of -40 °C to +85 °C supports industrial and commercial environments. The THS7353 is fabricated using Texas Instruments' complementary silicon-germanium BiCom-III process. This process supports the integration of three video channels, filtering functions, multiplexing, gain control, and digital control into a compact low-power device. The 20-TSSOP package supports surface-mount PCB assembly while providing separate routing flexibility for three video channels. Typical deployments include buffering component video and computer video outputs, switching between two video sources through the 2:1 multiplexer, filtering unwanted video-frequency content, and protecting source devices from downstream loading. Portable and projector designs benefit from the 2.7 V minimum supply and 16.2 mA quiescent current at 3.3 V, although system-level power depends on the selected configuration and output loading. Design the I2C address and control register settings before laying out the PCB, and confirm compatibility with the video timing and filter requirements of the target source. Decoupling and analog return paths should be arranged to minimize switching noise and ground potential differences between the amplifier and video source. This product page combines manufacturer specifications, application guidance, candidate replacement analysis, and practical PCB considerations. It identifies where THS7353PW fits, which published alternatives remain unverified as true pin-to-pin replacements, and which design parameters should be checked before approving a substitution.

Devis Contact
THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments
THS7375

THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments

The THS7375 is a low-power, single-supply, 3 V to 5 V four-channel integrated video buffer from Texas Instruments, fabricated using the complementary Silicon-Germanium (SiGe) BiCom3X process. It is available in a lead-free and green (RoHS) compliant TSSOP-14 package. The device incorporates a sixth-order Butterworth filter that can be bypassed, making it useful as a digital-to-analog converter (DAC) reconstruction filter. With a rail-to-rail output stage and a fixed gain of 5.6 V/V (15 dB), the THS7375 is designed for SDTV video applications, providing excellent image quality and driving capability for both AC and DC coupled loads. A video amplifier is an electronic amplifier that processes video signals, typically providing gain, buffering, and filtering to ensure signal integrity over transmission lines. In the signal chain, the THS7375 sits between a video DAC or encoder and the output connector, performing reconstruction filtering and line driving. It belongs to the category of integrated video buffers, which are essential in consumer electronics, set-top boxes, DVD players, and video surveillance systems. The THS7375's integrated filters eliminate the need for external passive components, simplifying design and reducing board space. Key features include a 6th-order Butterworth filter with a cutoff frequency suitable for SDTV (standard-definition television) signals, a fixed gain of 5.6 V/V, and the ability to drive two lines per channel or 75-ohm loads. The device operates from a single 3 V to 5 V supply, making it compatible with common digital logic levels. The rail-to-rail output stage ensures maximum output swing, and the low power consumption makes it ideal for battery-powered or power-sensitive applications. Technically, the THS7375 uses the BiCom3X process, which combines bipolar and CMOS transistors on a silicon-germanium substrate, offering high-speed performance with low power. The integrated filter is a 6th-order Butterworth type, providing a flat passband and sharp roll-off to remove out-of-band noise and aliasing artifacts. The device also features an internal gain of 5.6 V/V, which is optimized for driving video loads with proper termination. Typical applications include video buffer and line driver for SDTV signals in set-top boxes, DVD players, video recorders, and surveillance systems. It is also suitable for driving video signals from DaVinci processors and other video encoders. The THS7375's ability to drive two lines per channel allows for flexible routing in complex video distribution systems. When designing with the THS7375, ensure proper power supply decoupling with a 0.1 uF ceramic capacitor close to the VCC pin. The input should be AC-coupled if the source has a DC offset, and the output should be terminated with 75-ohm resistors to match the characteristic impedance of the cable. The filter bypass pin can be used to disable the internal filter if external filtering is preferred.

Devis Contact
THS788PFD - 200 MHz Quad-Channel 13 ps TMU | Texas Instruments
THS788PFD

THS788PFD - 200 MHz Quad-Channel 13 ps TMU | Texas Instruments

The Texas Instruments THS788PFD is a four-channel time measurement unit (TMU) using time-to-digital converter architecture, with 8 ps single-shot accuracy, 13 ps resolution derived from an external 200 MHz controller clock, and a measurement result range of 7 s in a 100-pin HTQFP package. It supports a 200 MHz event-input rate and provides LVDS-compatible event inputs, an LVDS result interface, four event channels, and a synchronization channel. A time measurement unit is a specialized clock-and-timing semiconductor that converts the elapsed time between events into a digital result. The THS788 belongs to the TMU hierarchy, where its TDC architecture combines fine timing resolution with high-rate event capture. This makes it suitable for systems requiring precise timing rather than ordinary counting, including synchronized instrumentation, pulsed systems, test equipment, and communications or industrial timing subsystems. The key performance feature is 8 ps single-shot accuracy, supported by a 13 ps least-significant-bit resolution. The external controller clock operates at 200 MHz, and the event input rate can reach 200 MHz. The 7 s result range supports substantially longer measurement intervals than the 13 ps conversion resolution alone would imply, depending on the configured measurement sequence and system implementation. LVDS-compatible interfaces provide high-speed, noise-resistant signaling for demanding board environments. Technically, the THS788 uses a fast TDC architecture to perform time measurements across four event channels. Its inputs are designed for LVCMOS or LVDS signaling, while the result output is identified as LVDS. The synchronized architecture and dedicated sync channel make the device suitable for multi-event acquisition where repeatable timing relationships matter. The stated low temperature coefficient of 0.1 ps/°C indicates attention to timing stability over temperature. Typical applications include high-speed test and measurement systems, pulsed-signal analysis, synchronization of multiple timing events, industrial automation requiring deterministic event capture, and communications equipment that must measure narrow time intervals. The device can also support scientific instrumentation where event timing accuracy directly affects the quality of the collected result. Designers should treat the external 200 MHz clock, LVDS-compatible input routing, result interface, decoupling, and high-speed return paths as an integrated signal-integrity problem. Input timing, trace length, termination, and controller configuration must be evaluated together because the 13 ps resolution does not guarantee end-to-end system accuracy without clean clocking, controlled stimulus, and correct interface implementation. This page combines the verified manufacturer and distributor information for the THS788PFD with practical selection guidance, application analysis, pricing references, and an honest assessment of available drop-in alternatives.

Devis Contact
THS788PFDT - 200MHz 4-Channel 8ps Timing IC | Texas Instruments
THS788PFDT

THS788PFDT - 200MHz 4-Channel 8ps Timing IC | Texas Instruments

The Texas Instruments THS788PFDT is a four-channel time measurement unit (TMU) built around a time-to-digital converter architecture, with 8 ps single-shot accuracy, 13 ps resolution derived from a 200 MHz external controller clock, and fast LVDS-compatible event inputs. The device is packaged in a 100-terminal 14 x 14 mm HTQFP surface-mount package and is intended for precision time-interval measurement applications. A time measurement unit is a specialized timing IC that converts the arrival time of an event into a digital value relative to a synchronization reference. The THS788 places a time-to-digital converter inside each measurement channel, allowing timing information to be captured with picosecond-class resolution instead of relying on a general-purpose counter clock. Its hierarchy runs from time measurement unit to time-to-digital converter, then to application-specific clock and timing IC and semiconductor. Key features include four measurement channels, 8 ps single-shot accuracy, 13 ps time-to-digital-converter resolution, and LVDS-compatible event inputs. The 200 MHz master clock determines the nominal TDC timing resolution, while a sync-channel input establishes time zero. According to the manufacturer product page, the device uses fast LVDS-compatible interfaces for its event inputs and supports calibrated timing calculations relative to the synchronization reference. The device supports fast event capture through hit latches, which latch an event edge before the timing data is processed. This architecture is useful when several channels must respond to closely spaced signals and the relative delay between them must be measured reliably. The controller interface and external clock remain essential parts of the measurement system because synchronization, calibration, and digital result transfer determine the integrity of the captured timing data. Typical applications include pulsed-laser range measurement, optical communication timing, radar and test instrumentation, high-speed trigger correlation, and industrial diagnostics that compare an event against a periodic reference. In such systems, the sync channel defines time zero, each event input records its relative arrival time, and the external controller applies calibration values before reporting the result. A critical design consideration is preserving the integrity of the 200 MHz reference clock and the LVDS-compatible event signals. Route timing-sensitive inputs as controlled-impedance nets, keep the clock away from high-current switching nodes, and use the exposed-pad land pattern and thermal vias recommended in the package drawing. Differential timing measurements are only as accurate as the reference distribution and input return-loss behavior of the complete board. This page consolidates the manufacturer timing specifications, package details, sourcing channels, and engineering guidance for the THS788PFDT, adding pin-connection and thermal-placement guidance that engineers would otherwise have to derive across multiple technical documents.

Devis Contact
THS789PFD - Quad-Channel 200MHz Time Measurement IC | TI
THS789PFD

THS789PFD - Quad-Channel 200MHz Time Measurement IC | TI

Texas Instruments THS789PFD is a quad-channel time measurement unit (TMU) with a 200 MHz measurement clock, one output, and a 100-pin HTQFP package measuring 14 mm by 14 mm. The device is listed for commercial-grade operation from 0 °C to 70 °C and is supplied in a tray. Its verified product identity also includes an exposed thermal pad and surface-mount construction. A time measurement unit is a specialized clock-and-timing semiconductor that measures elapsed time by comparing reference events. A multi-channel TMU extends this function across several independent measurement paths, making it useful when a system must acquire timing relationships, delays, pulse widths, or event intervals without implementing each measurement function as discrete logic. The THS789 therefore belongs to the clock-and-timing IC category and the broader application-specific timing semiconductor hierarchy. The principal verified specifications are four measurement channels, a 200 MHz timing reference, and one output. The 200 MHz reference corresponds to a 5 ns reference period, while the quad-channel architecture permits parallel timing observations. The 100-pin HTQFP package provides numerous external connections for timing inputs, control, power, and outputs, while the exposed pad supports heat transfer from the device to the PCB. The THS789PFD is specifically identified as a Time Measurement IC and is marketed by DigiKey under the Application Specific Clock/Timing classification. This distinguishes it from conventional general-purpose timers by emphasizing precision event-interval measurement across four channels. The exact input voltage range, minimum measurable interval, timing accuracy, propagation delay, output characteristics, and power specifications are not included in the supplied verified excerpts and should be taken from the complete manufacturer datasheet before design release. Typical engineering uses include industrial automation equipment, communications timing analysis, instrumentation, automated test systems, and embedded systems that compare multiple event arrivals. The 100-pin package and exposed pad make careful PCB layout, grounding, and thermal management important. In multi-channel systems, signal integrity at the timing inputs can materially affect measurement consistency, so controlled impedance, short return paths, and clean reference distribution should be prioritized. A principal design trade-off is package size versus channel density: the 14 mm by 14 mm HTQFP offers extensive connectivity for four timing channels but requires more PCB area than a compact mixed-signal package. Engineers should also confirm the complete electrical limits and interface timing before substituting another device or extending the operating temperature beyond the verified 0 °C to 70 °C range. This product record combines verified manufacturer and distributor identity, package and ordering information, commercial availability, and explicit engineering guidance for evaluating the THS789PFD. It also distinguishes confirmed facts from parameters that still require review in the full Texas Instruments datasheet, supporting faster procurement and design planning without treating unverified specifications as guaranteed.

Devis Contact
THS8135PHP - 10-Bit Triple 240-MSPS Video DAC | TI
THS8135PHP

THS8135PHP - 10-Bit Triple 240-MSPS Video DAC | TI

The Texas Instruments THS8135PHP is a triple 10-bit video digital-to-analog converter optimized for video and graphics applications, with a maximum sampling rate of 240 MSPS in a 48-lead HTQFP package measuring 7 mm by 7 mm. It operates from a 3.3 V analog supply and a 1.8 V digital supply, separating sensitive analog signaling from lower-voltage digital control and data inputs. A DAC is a data converter that translates digital codes into proportional analog voltages or currents. Video DACs belong to the broader ADC/DAC and data-converter IC hierarchy, where they sit between parallel digital pixel data and analog signals used by display or video-processing circuitry. The THS8135PHP combines three converters with circuitry for bi-level or tri-level synchronization and blanking-level generation. The principal features of this device are its three independent 10-bit conversion channels, 240 MSPS performance, parallel digital interface, and dedicated analog and digital supply rails. Each converter resolves the video signal into 10-bit steps. The parallel interface supports direct connection to video data sources without requiring a serial interface or a separate high-speed communication protocol. The package also provides a consolidated implementation for three color channels rather than requiring three separate DAC packages. The architecture is tailored to conventional component and graphics video systems. ITU-R BT.601-compatible full-scale output is identified for this device, making its output scaling suitable for standard-definition digital-video workflows. Bi-level and tri-level sync generation can produce the blanking levels required when converting active digital video into analog composite video. The 3.3 V analog rail and 1.8 V digital rail support partitioned supply planning, although both rails and the interface still require careful decoupling. Typical applications include SD and other video graphics systems, test and measurement video generation, digital signage, display-processing boards, and industrial imaging panels. The device is particularly useful when three synchronized analog outputs are required and the source interface already provides parallel pixel data. Its 240 MSPS ceiling provides substantial timing margin for common progressive video rates. PCB design should keep analog and digital return currents separated, place supply capacitors close to their corresponding pins, and route the parallel data bus with matched-length practices where timing margin is limited. The 48-lead HTQFP also requires careful thermal design because sustained high update rates can increase package dissipation. Use the manufacturer's pin-description table when assigning every power, data, clock, sync, and output connection. This page combines the device's principal conversion specifications, application guidance, package details, and engineering-focused replacement considerations. It also organizes sourcing information and drop-in comparison points into a format intended to accelerate schematic review, footprint verification, and prototype planning.

Devis Contact
THS8136PHP - Triple 10-Bit 180-MSPS Video DAC | Texas Instruments
THS8136PHP

THS8136PHP - Triple 10-Bit 180-MSPS Video DAC | Texas Instruments

The Texas Instruments THS8136PHP is a triple 10-bit, 180-MSPS graphics and video digital-to-analog converter in a 48-pin HTQFP package measuring 7 mm by 7 mm. It operates from a 3.3 V analog supply and a 1.8 V digital supply, integrating three parallel-input DAC channels with circuitry for bi-level sync and blanking-level generation. The converter is designed for video and graphics systems that require simultaneous red, green, and blue analog outputs. A DAC is a data converter that translates digital color or graphics codes into proportional analog voltages. The THS8136 belongs to the video DAC category, a specialized form of digital-to-analog converter used to drive analog display and video-processing equipment. Its parallel interface, triple-channel architecture, and integrated sync and blanking support place it within high-speed video signal-chain components rather than general-purpose precision DACs. The device provides three 10-bit DAC channels operating at sampling rates up to 180 MHz. Its 1.8 V digital supply supports modern digital graphics logic, while the 3.3 V analog supply provides the operating rail for the output converters. A common full-scale-adjustment resistor sets the output range of all three channels, and a 3.8-kilohm resistor is suitable for systems targeting approximately 700 mV full-scale output levels. The 0.015-microsecond settling time supports high-speed pixel and video timing requirements. Internal circuitry generates bi-level synchronization and blanking levels for RGB and YPbPr color spaces. These functions reduce the amount of external glue logic needed when generating composite or component video signals. The parallel digital inputs accept sampled video data, while the three analog outputs provide independent red, green, and blue channels. This integration makes the THS8136 useful in graphics controllers, video splitters, frame buffers, digital display systems, and test equipment. A typical implementation places the three DAC outputs on controlled impedance PCB traces and connects the digital input bus to the graphics or video source. Designers should terminate and route the high-speed digital interface carefully because edge-rate harmonics can radiate even though the maximum sampling rate is 180 MHz. Analog and digital return currents should be managed so switching activity does not disturb the output reference. The principal design trade-off is integration versus operating flexibility. The THS8136PHP combines three converters and video-control functions in one package, reducing external circuitry, but its dedicated video feature set makes it less suitable than a general-purpose DAC when arbitrary analog waveforms, calibration, or multiple independent output ranges are required. Confirm package pin assignments and exposed-pad requirements in the manufacturer datasheet before layout release. This product overview combines the manufacturer’s device description with package, interface, output-adjustment, and ordering details that help engineers assess the THS8136PHP before designing a video DAC signal chain. It also clarifies the distinctions among same-device ordering options and pin-compatible industrial-grade variants.

Devis Contact