Produits (44 000+)

TS902IDT - Dual 1.4MHz Rail-to-Rail Op Amp | STMicroelectronics
TS902IDT

TS902IDT - Dual 1.4MHz Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS902IDT is a dual general-purpose CMOS operational amplifier with rail-to-rail input and output voltage ranges, a 1.4 MHz gain-bandwidth product, and a low-power standby mode drawing 0.5 µA. The device is offered in the TS902IDT tape-and-reel configuration in a 14-pin small-outline package. Its dual amplifier arrangement provides two independent signal-conditioning channels in one package. A rail-to-rail operational amplifier is an amplifier whose input common-mode and output voltage ranges can extend close to the positive and negative supply rails. This makes the TS902 useful for low-voltage systems in which the signal can occupy much of the available supply voltage. In the broader device hierarchy, the TS902 is a dual CMOS operational amplifier, placing it within analog and mixed-signal integrated-circuit designs. The TS902IDT provides a 1.4 MHz gain-bandwidth product for general-purpose amplification at moderate frequencies. Its rail-to-rail input stage supports signal acquisition close to the supply limits, while the rail-to-rail output stage improves output-voltage range. A standby position reduces consumption to 0.5 µA and places the outputs in a high-impedance state, helping conserve power when the amplifier is not actively processing signals. The TS902IDT is specified for a temperature range of -40 °C to +125 °C. One retrieved technical listing identifies a maximum input offset voltage of 12 mV, while another reports a low bias current of 0.00015 µA. These figures support applications involving sensor interfaces, low-level signal conditioning, and battery-operated instrumentation where offset and input current are important selection criteria. Typical uses include portable sensor conditioning, industrial measurement, audio preamplification, low-voltage control systems, and current-feedback around transducers. The SOIC-14 package also permits a conventional surface-mount PCB layout with adequate separation between the two amplifier channels. Designers should account for the 12 mV maximum input offset when the application requires accurate DC measurements. Input and output stability must be evaluated with the selected feedback network and load, while supply bypassing should follow the manufacturer recommendations. The standby function should be driven only with signals that remain compatible with its defined logic levels. This product page combines package, temperature, frequency, offset, and power information with application-oriented engineering guidance. It also identifies the verified documentation links and explains the limits of the available drop-in replacement cross-reference, helping engineers distinguish a true pin-compatible substitution from a merely similar amplifier.

Devis Contact
TS912ID - Dual Rail-to-Rail CMOS Op Amp | STMicroelectronics
TS912ID

TS912ID - Dual Rail-to-Rail CMOS Op Amp | STMicroelectronics

STMicroelectronics TS912ID is a dual rail-to-rail CMOS operational amplifier with two independent amplifiers, an 8-pin SOIC package, and operation from single or dual supplies. Verified distributor listings identify it as a 2.7 V to 16 V device with approximately 800 kHz gain-bandwidth product and 1.3 V/us slew rate. The rail-to-rail input and output architecture supports signal stages whose operating range approaches the available supply voltage. An operational amplifier is an analog building block that uses high open-loop gain to amplify voltage differences while feedback determines the closed-loop behavior. A dual op-amp combines two amplifiers in one package, allowing designers to implement filters, buffers, level conversions, or paired signal-conditioning stages while reducing board area. CMOS construction supports low-power and low-noise signal-chain designs across industrial, instrumentation, communications, and consumer equipment. The TS912ID's rail-to-rail input range includes both supply rails, while its rail-to-rail output can swing close to the upper and lower limits. The verified 800 kHz bandwidth provides useful response for general-purpose low-frequency and moderate-frequency applications, while the 1.3 V/us slew rate supports faster transitions than very low-bandwidth precision amplifiers. Two independent, frequency-compensated amplifiers are contained in the same 8-SOIC package. Supply flexibility is central to the device: it can operate from a single 2.7 V minimum supply or from dual positive and negative rails. This makes it suitable for battery-powered instrumentation, active filtering, transducer interfaces, and general analog signal conditioning. Designers should still verify input and output common-mode limits, output-load behavior, noise, input-bias-current requirements, and stability against the conditions of the manufacturer datasheet. Typical uses include low-frequency active filters, sensor-signal conditioning, audio and communications interface blocks, voltage buffering, and two-channel sensor amplification. The SOIC-8 package is straightforward for conventional PCB assembly and breadboard or prototype layouts, although exposed-pad thermal management is not applicable. The primary design consideration is to place input, feedback, and decoupling components so that high-gain layouts remain stable. Keep sensitive input traces short, maintain a low-impedance ground reference, and follow the datasheet's recommended bypass capacitance. Verify the actual output swing against the load and required logic or sensor levels rather than assuming ideal rail-to-rail behavior. This page combines verified distributor pricing, manufacturer datasheet access, same-package replacement data, and practical selection guidance. It separates explicitly published facts from parameters requiring design verification, helping engineers source TS912ID without relying on generic amplifier descriptions.

Devis Contact
TS912IN - Dual Rail-to-Rail CMOS Op Amp | STMicroelectronics
TS912IN

TS912IN - Dual Rail-to-Rail CMOS Op Amp | STMicroelectronics

The STMicroelectronics TS912IN is a dual rail-to-rail CMOS operational amplifier with two amplifier channels, a 2.7 V to 16 V supply range, and an 8-pin Mini DIP package. The device supports single-supply or dual-supply operation, with rail-to-rail input and output voltage ranges. According to the manufacturer datasheet, its typical input bias current is only 1 pA, maximum input offset voltage is 2 mV, and supply current is approximately 200 µA per amplifier at a 3 V supply. These characteristics make the TS912IN suitable for low-power instrumentation, sensor interfaces, and signal-conditioning circuits that require low input bias and flexible supply operation. A CMOS operational amplifier is a voltage amplifier whose differential input controls the voltage applied to its output. Rail-to-rail input and output ratings allow the amplifier to operate close to the positive and negative supply rails, increasing the usable output range in single-supply systems. In the electronics hierarchy, the TS912IN is a dual operational amplifier, which belongs to the broader class of analog amplifier ICs and ultimately to integrated circuits used for analog signal processing. Key features include two independent amplifier channels, rail-to-rail input and output operation, and a 2.7 V to 16 V total supply range. The 1 pA typical input bias current is particularly useful for high-impedance sources because it minimizes source-loading error. Maximum input offset voltage of 2 mV supports accurate amplification of signals near the lower end of the input range. Operation from a 3 V supply at approximately 200 µA per amplifier also helps limit power consumption in battery-operated equipment. The TS912IN uses CMOS input circuitry to provide low bias current and low supply consumption. Rail-to-rail input behavior is important when the signal can approach either supply rail, while rail-to-rail output capability allows the output to use much of the available supply voltage. Designers should still account for output-current limits, load impedance, input common-mode behavior, and output-voltage headroom under the selected supply voltage and load conditions. Typical uses include low-power sensor signal conditioning, portable measurement instruments, battery-powered monitoring, and general-purpose analog filtering. The dual configuration allows one package to provide two amplifier channels for gain stages, buffers, comparators, or active filters. When the source impedance is high, the 1 pA typical bias current reduces loading, although PCB leakage and guard-ring techniques may still be necessary in demanding measurements. When designing around the TS912IN, use stable bypass capacitance at the supply pins and keep feedback components close to the amplifier pins to minimize parasitic effects. Confirm the required output swing, load, input range, and noise performance against the manufacturer datasheet before finalizing a high-gain or precision application. This page consolidates the verified manufacturer descriptions, distributor references, package information, technical characteristics, and substitution constraints for the TS912IN. It also distinguishes verified data from unavailable pricing, compliance, and pin-mapping details, helping engineers evaluate the amplifier without treating unverified substitute parts as drop-in equivalents.

Devis Contact
TS914ID - Quad Rail-to-Rail CMOS Op Amp | STMicroelectronics
TS914ID

TS914ID - Quad Rail-to-Rail CMOS Op Amp | STMicroelectronics

STMicroelectronics TS914ID is a quad rail-to-rail CMOS operational amplifier with a 1.4 MHz gain-bandwidth product, operating from 2.7 V to 16 V and supplied in a 14-pin SOIC package. The device accepts single or dual supply voltages and supports rail-to-rail input and output operation, allowing signals to approach either supply rail. Its extremely low 1 pA typical input bias current suits high-impedance sensing circuits, while the 2 mV maximum input offset voltage provides adequate precision for general-purpose analog signal conditioning. A CMOS operational amplifier is a voltage-controlled, high-gain analog building block whose differential input is amplified relative to ground or another reference voltage. The TS914 belongs to the operational-amplifier hierarchy, combining four amplifiers in one integrated circuit. It is designed for low-power, single-supply and dual-supply systems where four independent analog channels can be implemented in one compact 14-pin SOIC package. Key features include four amplifier channels, rail-to-rail input and output ranges, a 2.7 V to 16 V supply-voltage range, and a 1.4 MHz gain-bandwidth product. The typical input bias current of 1 pA is particularly valuable when source impedances are high, because it minimizes the voltage error caused by bias current. The reported 200 µA supply current per amplifier at 3 V also supports battery-powered and portable equipment when the required bandwidth is moderate. The TS914's CMOS input stage enables operation close to the supply rails and supports low input bias current. Its 1.4 MHz bandwidth is appropriate for general-purpose amplification, filtering, buffering, and signal conditioning rather than high-speed precision instrumentation. Because the maximum offset voltage is specified as 2 mV, applications demanding sub-millivolt accuracy require additional calibration or a more precise amplifier. Typical uses include four-channel sensor interfaces, low-frequency active filters, audio and communication signal conditioning, portable instrumentation, and industrial control modules. Placing all four channels in one SOIC package reduces board area and external component count. Input common-mode and output swing limits, output-current capability, noise, and stability should still be checked against the manufacturer datasheet before fixing the supply voltage and external network. For reliable single-supply operation, keep the input common-mode voltage within the supported range, place input and feedback components close to the device, and provide suitable bypassing at each supply pin. Decoupling requirements and compensation values must follow the manufacturer datasheet rather than generic assumptions. If the source resistance is high, account for input bias-current and capacitance errors, and confirm that the selected feedback topology remains stable at the intended gain. This product page consolidates verified manufacturer and distributor information with package, application, replacement, and design guidance. It distinguishes verified parameters from information that still requires datasheet review, helping engineers evaluate TS914ID without mistaking generic amplifier assumptions for guaranteed TS914ID characteristics.

Devis Contact
TS914IN - 4-Channel Rail-to-Rail Op Amp | STMicroelectronics
TS914IN

TS914IN - 4-Channel Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS914IN is a four-circuit, rail-to-rail CMOS operational amplifier designed for single or dual supply operation, with a 16 V maximum supply voltage, 1 pA typical input bias current, and a 2 mV maximum input offset voltage. The device is supplied in a 14-pin through-hole DIP package, allowing one package to implement four amplifier channels. A CMOS operational amplifier is a voltage-controlled, high-gain analog signal-processing component used for buffering, amplification, sensing, filtering, and feedback control. The TS914IN belongs to the operational amplifier hierarchy within analog integrated circuits, where its rail-to-rail input and output capability makes it suitable for systems whose signal levels approach the available supply rails. Key features include four amplifier circuits, rail-to-rail input and output operation, support for single or dual power supplies, very low 1 pA typical input bias current, and low input offset voltage no greater than 2 mV. According to the STMicroelectronics manufacturer datasheet, the device is intended for applications operating from a single supply or from dual supplies up to 16 V. The low input bias current is especially useful when the amplifier is connected to high-impedance sensors, because the amplifier contributes minimal loading to the source. Rail-to-rail behavior also broadens the usable input and output range in low-voltage systems. The trade-off is that the 14-pin DIP package is larger than modern surface-mount packages, making TS914IN more appropriate for through-hole, legacy, industrial, and prototyping assemblies. Typical uses include battery-powered instrumentation, sensor interfaces, low-voltage signal conditioning, sample-and-hold circuits, active filters, and general-purpose analog control systems. Its four independent channels can reduce the number of packages required when a board needs several similar low-power amplifier functions. When designing around TS914IN, verify input and output common-mode limits, output-current capability, operating-temperature limits, and stability requirements against the manufacturer datasheet for the exact operating conditions. Input bias, offset, and supply currents should be checked with the source impedance and signal bandwidth, particularly in high-impedance precision measurements. This page consolidates verified manufacturer and distributor information, package and pin details, replacement constraints, comparison data, and application-specific engineering guidance. It distinguishes confirmed specifications from unavailable values so engineers can make sourcing and PCB-retention decisions without relying on unsupported assumptions.

Devis Contact
TS921ID - 4MHz High-Output RRIO Op Amp | STMicroelectronics
TS921ID

TS921ID - 4MHz High-Output RRIO Op Amp | STMicroelectronics

The STMicroelectronics TS921ID is a single rail-to-rail input and output BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and 80 mA output-current capability in an 8-pin SOIC package. An operational amplifier is a voltage-controlled differential amplifier that uses high open-loop gain to amplify small input signals. The TS921 belongs to the rail-to-rail input/output, or RRIO, family, allowing its input common-mode range and output swing to approach the supply rails. This makes it useful for low-voltage battery-powered equipment, sensor interfaces, audio stages, industrial controls, and portable instruments where the signal can occupy much of the available supply range. The TS921's principal features include low input noise of 9 nV/sqrt(Hz), a 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and an output stage capable of delivering 80 mA. The manufacturer identifies the device as optimized and fully specified for 3 V and 5 V supplies, while verified distributor data also gives a 2.7 V to 12 V operating-voltage range. Rail-to-rail operation reduces the need for separate positive and negative supply rails in single-supply designs. The BiCMOS process combines bipolar input characteristics with CMOS output circuitry. In practical signal chains, the TS921 can condition low-level sensor outputs, buffer precision ADC inputs, or provide general-purpose gain. Its 80 mA output capability is useful for driving moderate loads, although sustained heavy loading can reduce output swing and increase power dissipation. The 4 MHz bandwidth supports applications requiring moderate rather than high-frequency closed-loop performance. Typical uses include battery-operated instrumentation, low-voltage audio, industrial sensor conditioning, active filters, and portable measurement equipment. The SOIC-8 format supports conventional surface-mount assembly, while the manufacturer datasheet provides the authoritative pin connection and recommended application information for layout and decoupling decisions. For single-supply operation, reserve output headroom for the load and check the input common-mode range across the complete signal excursion. Place the supply bypass capacitor close to the positive and ground pins, and use short, low-impedance feedback routes to limit parasitic feedback and preserve stability. This product page combines the verified manufacturer and distributor information with package, application, comparison, and design guidance. It identifies where TS921ID fits, highlights the 4 MHz bandwidth and 80 mA output-current capabilities, and clearly separates confirmed data from engineering details that require additional verification.

Devis Contact
TS921IN - 4MHz Rail-to-Rail Op Amp | STMicroelectronics
TS921IN

TS921IN - 4MHz Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS921IN is a single-amplifier operational amplifier with a 4 MHz gain-bandwidth product, 1 V/µs slew rate, rail-to-rail input and output capability, and an 8-DIP package. Its 80 mA typical output current supports higher-capacitive and load-driving capability than a conventional low-current general-purpose amplifier. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, compare, filter, and control signals. The TS921IN belongs to the operational-amplifier hierarchy, which falls under analog amplifier ICs and broader semiconductor signal-conditioning devices. Its rail-to-rail input and output architecture is useful when the usable input or output range must extend close to the supply rails. Key characteristics include a 4 MHz gain-bandwidth product, 1 V/µs slew rate, low input-referred noise density of 9 nV/√Hz, and typical output current of 80 mA. The single-amplifier configuration allows a PCB footprint to remain compact, while the 8-DIP package provides straightforward through-hole assembly. The listed operating temperature range is -40°C to +125°C, supporting industrial-temperature applications. The TS921IN combines rail-to-rail signal handling with relatively high bandwidth and output-drive capability. Its low-noise specification is particularly useful for low-level audio, instrumentation, sensor-interface, and general analog signal-conditioning circuits. The 80 mA output current also allows the amplifier to drive more demanding loads than a typical comparator-oriented or ultra-low-power op amp, provided the supply voltage and thermal limits remain satisfied. Typical uses include low-level sensor amplification, active filtering, audio preamplification, buffer stages, threshold and comparator-style interfaces, and general industrial control circuitry. It can also serve as a rail-to-rail input/output buffer in systems where the input signal approaches either supply rail. Designers should still verify stability, output swing, load capability, and noise performance against the complete circuit requirements. A key design consideration is the trade-off between bandwidth, noise, and output drive. The TS921IN is more capable than a low-power, low-bandwidth amplifier, but it is not necessarily the optimal choice for every precision or micropower design. Input and output stability should be evaluated with the actual source impedance, load, supply voltage, and external compensation network. This page combines verified distributor specifications and availability with a practical TS921IN selection guide, application analysis, datasheet references, and defensible family alternatives. Pricing reflects the verified $0.58 unit-price listing as of October 29, 2026, while unavailable technical fields are explicitly marked rather than estimated.

Devis Contact
TS921IPT - 4MHz RRIO High-Output Op Amp | STMicroelectronics
TS921IPT

TS921IPT - 4MHz RRIO High-Output Op Amp | STMicroelectronics

The STMicroelectronics TS921IPT is a single, rail-to-rail input and output BiCMOS operational amplifier featuring 4 MHz gain-bandwidth product, 1 V/us slew rate, 9 nV/Hz low-noise performance, and 80 mA output-current capability in an 8-pin TSSOP package. The device is optimized and fully specified for operation from 3 V and 5 V, with operating supply voltage extending to 12 V. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to buffer, amplify, filter, or compare voltage signals. The TS921 belongs to the broader rail-to-rail operational-amplifier category, combining low-noise BiCMOS input and output stages with the ability to swing close to both supply rails. This makes it useful when signals must be processed with minimal rail-to-rail headroom restrictions. The TS921IPT combines rail-to-rail input and output operation with a 4 MHz gain-bandwidth product and 1 V/us slew rate. Its 9 nV/Hz voltage-noise density supports precision signal-chain work, while its 80 mA output-current capability can drive up to 32 loads according to the manufacturer description. Low distortion, internal ESD protection rated at 1.5 kV, and latch-up immunity improve robustness in practical analog circuits. The BiCMOS architecture balances low input-noise behavior with high output-drive capability. A gain-bandwidth product of 4 MHz supports signal amplification at moderate frequencies, and the 1 V/us slew rate improves large-signal response compared with slower general-purpose amplifiers. The 8-pin TSSOP-8 package permits compact surface-mount implementation, while rail-to-rail operation reduces the need to keep input and output voltages strictly inside the supply rails. Typical uses include low-noise sensor conditioning, audio signal paths, current sensing, active filtering, instrumentation, and general-purpose buffering. The 80 mA output capability is particularly relevant when the amplifier must drive a relatively heavy capacitive or resistive load. Designers should still check load stability and output-current limits for the complete application rather than relying on peak capability alone. Decoupling should be placed close to the supply pins, and sensitive input routing should avoid proximity to switching nodes and high-current return paths. The amplifier must operate within its specified common-mode and supply-voltage limits. Because the available package drawing could not be independently verified against a pin-description table, use the manufacturer datasheet before assigning PCB tracks or making pin-sensitive substitutions. This page combines the verified TS921IPT operating characteristics with practical application guidance, sourcing instructions, and a focused drop-in assessment. The alternative list intentionally excludes unverified cross-package or speculative equivalents so that engineers can distinguish a genuine TSSOP-8 replacement from a merely similar amplifier.

Devis Contact
TS9222ID - Dual Precision Rail-to-Rail Op Amp | STMicroelectronics
TS9222ID

TS9222ID - Dual Precision Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS9222ID is a dual precision operational amplifier optimized for low-noise and stable signal amplification, with rail-to-rail input and output operation, 4 MHz gain-bandwidth product, and 1.3 V/us slew rate in an 8-pin SOIC package. It operates from 2.7 V to 12 V and is specified for -40C to +125C operation. An operational amplifier is an active analog component that uses high open-loop gain to amplify voltage differences between its differential inputs. Within the analog signal-chain hierarchy, an op amp sits between passive sensor conditioning and higher-level conversion or control functions. Rail-to-rail input and output operation allows the TS9222ID to accept signals near the positive or negative supply rail, while its output can also swing close to those rails. Key characteristics include a maximum input offset voltage of 500 uV, 80 mA output current per channel, and low input bias current. The 4 MHz gain-bandwidth product supports closed-loop operation at moderate signal frequencies, while the 1.3 V/us slew rate gives adequate performance for precision feedback networks, instrumentation, and low-to-moderate-frequency signal conditioning. The dual configuration provides two amplifiers in one package, reducing component count on analog boards. The TS9222ID is built for precision and stability rather than maximum bandwidth. Its 500 uV maximum input offset voltage limits the output error created by input imbalance in a unity-gain configuration. Rail-to-rail inputs help preserve signal integrity in sensor interfaces where the operating point may sit near a supply rail. The stated 80 mA per-channel output capability also allows the amplifier to drive heavier loads than a purely high-impedance signal-processing stage. Typical applications include current sensing, bridge and instrumentation amplifiers, sensor conditioning, audio preamplification, industrial measurement systems, and automotive electronic modules. The -40C to +125C temperature range supports extended industrial environments, provided that the board-level power supply, bypass capacitors, and stability network follow the manufacturer's recommended implementation. For reliable operation, place the input and feedback components close to their corresponding pins, bypass each supply rail locally, and verify capacitive-load stability with an isolation resistor when driving cables, ADC inputs, or other long capacitive loads. Use the manufacturer pin-description table when assigning PCB tracks and confirm that the selected amplifier configuration remains stable across the intended gain, load, and supply range. This page combines package, precision, temperature-range, and interface guidance with same-family drop-in options and a parameter-by-parameter comparison. It is intended to help engineers shorten selection work while preserving the electrical and layout constraints that determine analog performance.

Devis Contact
TS9224ID - 4-Channel Precision Rail-to-Rail Op Amp | STMicroelectronics
TS9224ID

TS9224ID - 4-Channel Precision Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS9224ID is a four-circuit, general-purpose operational amplifier optimized for precision, low noise, and stability, with rail-to-rail input and output operation in a 14-pin SOIC package. Key ratings include 500 uV maximum input offset voltage, 4 MHz gain-bandwidth product, 1.3 V/us slew rate, 9 nV noise, and 500 pF capacitive-load drive capability. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify small voltage differences. Its hierarchy extends from operational amplifier to analog amplifier, linear amplifier, and analog semiconductor. The TS9224 quad configuration integrates four amplifiers into one package, reducing board area while preserving independent signal paths for instrumentation, buffering, filtering, and precision control applications. Rail-to-rail input and output behavior supports operation near the supply rails, which is useful when signal range is limited by available supply voltage. The 500 uV maximum offset-voltage rating supports precision-focused designs, while the 4 MHz gain-bandwidth product and 1.3 V/us slew rate provide useful bandwidth for general-purpose closed-loop amplifier stages. The manufacturer also identifies 500 pF capacitive-load drive and 9 nV noise as principal device characteristics. The TS9224 family is optimized around low-noise, high-precision operation with particular emphasis on stability. This combination suits instrumentation and industrial signal paths where input offset, noise, and closed-loop behavior affect measurement quality. Four independent amplifiers in a single package can also simplify designs requiring multiple similar analog channels, although each amplifier requires correct input common-mode, output swing, and output-current conditions. Typical uses include low-level sensor conditioning, current-sense amplifier outputs, bridge-signal interfaces, analog filtering, and precision control loops. In each case, stable closed-loop operation and rail-to-rail signal handling can reduce the need for separate input or output buffers, provided the feedback network is designed for the required gain and bandwidth. For PCB implementation, use the manufacturer's pin configuration when assigning inputs, outputs, supply rails, and feedback components. Place input, output, feedback, and decoupling connections to minimize loop area and susceptibility to noise. Because the device can drive capacitive loads up to 500 pF, isolate difficult loads with series resistance when necessary to preserve stability. This product page combines the TS9224ID electrical characteristics, package details, drop-in alternatives, comparison parameters, and application-focused design guidance to support component selection, PCB planning, and precision analog circuit design.

Devis Contact
TS922AID - Dual Rail-to-Rail Op Amp | STMicroelectronics
TS922AID

TS922AID - Dual Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS922AID is a dual rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with low noise of 9 nV/√Hz, low distortion of 0.005%, and high output current of 80 mA in an 8-pin SOIC package. It operates from the supply rails up to 12 V and is designed for low-impedance loads. An operational amplifier is an analog signal-conditioning IC that amplifies the difference between two input voltages. A dual amplifier contains two independent amplifiers in one package, while a rail-to-rail input and output stage allows operation close to both supply-voltage limits. The TS922AID therefore occupies the amplifier, analog IC, and semiconductor hierarchy while serving precision audio, buffer, and low-load drive applications. The principal features include rail-to-rail input and output capability, 80 mA output current, 9 nV/√Hz input noise, 0.005% distortion, a 4 MHz gain-bandwidth product, and a 1 V/µs slew rate. These characteristics combine low-noise signal handling with enough output drive to operate 32 low-impedance loads according to the manufacturer description. The TS922AID uses a BiCMOS process that combines bipolar input circuitry with CMOS output stages. Its high output current is the principal architectural distinction from many general-purpose dual amplifiers, especially when the output must remain low-impedance while operating near the supply rails. The 3 V and 5 V optimization also makes it appropriate for compact, low-voltage analog systems. Typical uses include audio preamplifier stages, active filters, sensor-conditioning circuits, low-impedance buffer applications, and portable test or measurement equipment. The dual configuration allows two related signal paths to be implemented in one package, reducing board area and simplifying dual-rail analog front ends. For stable operation, follow the manufacturer datasheet for supply-decoupling close to the power pins and for output-load limits. Input and output common-mode ranges, input bias current, offset voltage, and exact operating-temperature limits should be checked against the specific operating point before production release. This page organizes the manufacturer specifications, sourcing information, application guidance, and verified drop-in options for engineers evaluating the TS922AID. It also distinguishes confirmed pin-compatible choices from family members that differ in grade, package, or packaging and therefore require separate engineering review.

Devis Contact
TS922ID - Dual Rail-to-Rail Op Amp | STMicroelectronics
TS922ID

TS922ID - Dual Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS922ID is a dual, rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, housed in an 8-pin small-outline integrated circuit package. Its two amplifier channels feature high output-current capability for driving low-load impedances, while the rail-to-rail input and output stages make it suitable for systems whose signal levels approach the supply rails. An operational amplifier is a high-gain, high-impedance analog amplifier used to amplify, buffer, compare, or filter signals. The TS922ID belongs to the operational-amplifier family within analog integrated circuits, providing two independent amplifier channels in one package. Rail-to-rail operation means the amplifier can process input and output signals close to the positive and negative supply limits, which improves utilization of the available supply voltage in mixed-signal systems. The TS922 and TS922A family is specifically described by STMicroelectronics as a dual BiCMOS operational-amplifier family optimized and fully specified for 3 V and 5 V operation. The TS922ID also provides high output currents, allowing the device to drive low-load impedances. These characteristics make it useful in audio output stages, sensor-conditioning circuits, active filters, and low-voltage industrial or battery-powered equipment. The TS922ID is identified as an active, RoHS-compliant, standard general-purpose amplifier with an operating temperature range of -40 °C to +125 °C. The device is supplied in an SOIC-8 package, and distributor listings identify the TS922ID as a dual amplifier with rail-to-rail operation. Because the device combines two amplifiers in one package, it can also reduce board area in designs that require two buffered or amplifying channels. A key application consideration is that the available supply voltage and load current determine whether the output stage remains within its intended operating region. Designers should also observe the absolute maximum ratings and recommended operating conditions in the STMicroelectronics datasheet, provide appropriate bypass capacitance near the supply pins, and confirm that the connected load does not exceed the amplifier's specified drive capability. This page combines the manufacturer datasheet, distributor inventory information, and verified cross-reference findings. It also distinguishes documented TS922ID data from parameters that require confirmation from the full datasheet or distributor inventory before production release.

Devis Contact
TS922IN - Dual 4MHz Rail-to-Rail Op Amp | STMicroelectronics
TS922IN

TS922IN - Dual 4MHz Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS922IN is a dual, rail-to-rail input and output BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a 4 MHz gain-bandwidth product, 1 V/µs slew rate, and high output-current capability. The device is supplied in an 8-pin Mini DIP package and contains two independent amplifiers. According to the STMicroelectronics manufacturer datasheet, its rail-to-rail stages allow input and output voltages to approach the supply rails, while the BiCMOS architecture combines low input bias current with CMOS-style low power consumption. An operational amplifier is a high-gain, high-impedance analog signal-conditioning circuit used for voltage amplification, buffering, filtering, and closed-loop feedback control. Within the broader semiconductor hierarchy, the TS922IN is a dual precision analog amplifier, falling under the categories of operational amplifier, analog IC, and semiconductor. Its two amplifier sections can independently process signals or operate together in differential and analog signal-conditioning circuits. Key electrical characteristics include a 4 MHz gain-bandwidth product, 1 V/µs slew rate, low noise identified as 9 nV/√Hz, and output-current capability up to 80 mA. The supported supply range is 2.7 V to 12 V, with operation optimized around 3 V and 5 V rails. Rail-to-rail input and output behavior is especially useful when signal amplitudes occupy much of the available supply-voltage range. The 80 mA output capability also permits relatively low-load-impedance drive compared with many general-purpose dual amplifiers. The TS922 family uses a BiCMOS input stage to combine bipolar-device characteristics with CMOS power behavior. Its dual architecture saves board area by placing two amplifiers in one package. The manufacturer describes the devices as optimized and fully specified for 3 V and 5 V operation, while also identifying a wider operating range extending to 12 V. This makes the TS922IN relevant to industrial controls, sensor interfaces, audio paths, data acquisition, and general dual-amplifier designs. Typical uses include low-level sensor conditioning, active filtering, audio preamplification, voltage buffering, and mixed-signal circuits requiring two amplifiers. The rail-to-rail output is useful when driving subsequent stages whose common-mode range is limited. The high output current can also reduce the need for an additional output-buffer stage in moderate-load applications. Designers should verify output swing, input common-mode behavior, load stability, and noise at the actual supply voltage and operating frequency. Decoupling capacitors should be placed close to the supply pins, and unused amplifier sections should be configured according to the manufacturer datasheet rather than left floating. The 8-pin Mini DIP package also requires adequate spacing for through-hole assembly and careful handling during insertion. This page combines manufacturer specifications, verified distributor information, package guidance, drop-in alternatives, comparison data, and practical application notes. It is intended to help engineers identify whether the TS922IN fits a 3 V or 5 V dual-amplifier design before purchasing or modifying an existing PCB.

Devis Contact
TS922IPT - Dual Rail-to-Rail 4 MHz Op Amp | STMicroelectronics
TS922IPT

TS922IPT - Dual Rail-to-Rail 4 MHz Op Amp | STMicroelectronics

STMicroelectronics TS922IPT is a dual rail-to-rail input and output BiCMOS operational amplifier rated for 2.7 V to 12 V operation. It provides two amplifier channels, 4 MHz gain-bandwidth performance, a 1.3 V/us slew rate, and rail-to-rail input and output stages in an 8-pin TSSOP package. The device is optimized and fully specified for 3 V and 5 V systems. An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its two inputs while providing high input impedance, low output impedance, and stable operation around a feedback-defined voltage. The TS922 belongs to the operational-amplifier hierarchy, where a dual BiCMOS amplifier combines bipolar input characteristics with CMOS-compatible output drive for low-power mixed-signal systems. The TS922IPT's rail-to-rail inputs allow sensing signals close to either supply rail, while rail-to-rail outputs improve dynamic range in single-supply circuits. Its high output-current capability is intended for driving relatively low-impedance loads. Low distortion of 0.005% and very low noise make the amplifier useful in audio and other precision analog paths. The dual configuration also reduces component count when two independent gain stages are required. STMicroelectronics identifies the TS922 family as a BiCMOS dual operational amplifier optimized for 3 V and 5 V operation. The 4 MHz gain-bandwidth product supports moderate-bandwidth signal conditioning, including active filtering, sensor amplification, and audio stages. The 1.3 V/us slew rate improves large-signal response, although higher-frequency designs should verify stability, load capacitance, and noise-gain requirements. Typical uses include audio preamplification, low-load-impedance driver stages, sensor interfaces, active filters, and portable 3 V or 5 V equipment. It is particularly relevant when dual-channel signal conditioning is needed without introducing rail-to-rail input/output limitations common in older amplifier families. PCB design should keep input and feedback paths short, place compensation or filtering capacitors close to their associated pins, and maintain a solid ground reference. Decoupling capacitors should be connected to the supply and ground pins with minimal loop area. Designers should also verify output swing and capacitive-load stability against the circuit's load current and impedance. This product page combines manufacturer specifications, exact drop-in candidate screening, application guidance, pin assignments, and a practical comparison framework. It helps engineers distinguish electrically different family variants from mechanically compatible alternatives before approving a PCB substitution.

Devis Contact
TS924ID - Quad Rail-to-Rail Op Amp | STMicroelectronics
TS924ID

TS924ID - Quad Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS924ID is a four-circuit, rail-to-rail BiCMOS operational amplifier with an 80 mA output-current rating, 80 dB CMRR, and a maximum bias current of 0.1 µA, supplied in a 14-pin small-outline package. The device is optimized for 3 V and 5 V operation and is intended for low-voltage signal conditioning, audio, portable equipment, and general-purpose analog systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. A quad package contains four independent amplifier sections, allowing one TS924ID to implement four amplifier channels in a single 14-pin package. Rail-to-rail input and output operation helps preserve signal range in low-voltage systems where conventional amplifier stages may approach their supply limits. Key features include four amplifier circuits, rail-to-rail operation, an 80 mA cited output-current capability, 80 dB common-mode rejection ratio, and a maximum input bias current of 0.1 µA. The TS924 family is described as a low-noise, low-distortion BiCMOS design. Its low bias current is particularly useful in high-impedance sensing paths, while the rail-to-rail characteristics support compact, low-voltage equipment. The bipolar input stage and CMOS output stage form the BiCMOS architecture used in the TS924 family. Input bias current, common-mode rejection ratio, offset voltage, output-current capability, noise, and distortion are the principal parameters to check when comparing it with other quad low-voltage operational amplifiers. The verified TS924ID information cites a maximum offset of 5000 µV, a maximum bias current of 0.1 µA, and an 80 mA output-current feature. Typical uses include low-voltage audio signal conditioning, portable and battery-operated equipment, current or voltage sensing interfaces, active filtering, and general analog buffers. Four amplifiers in one package can reduce board area when a design needs several channels. Applications requiring wider supply voltage, lower offset, lower noise, or different logic levels should verify those requirements against the complete manufacturer datasheet before production use. Designers should provide adequate input and output bypassing, verify stable operation with the intended load and feedback network, and confirm that the amplifier input common-mode range includes the full signal swing. Because the output-current figure is a headline feature rather than a complete load-capability specification, cable, headphone, and capacitive-load applications require careful review of the datasheet's output-stage limits. This product page consolidates verified distributor availability, pricing, environmental information, same-package alternatives, and practical selection guidance. It also distinguishes documented TS924ID facts from parameters that still require confirmation from the manufacturer datasheet, helping engineers narrow a replacement without making an unverified electrical assumption.

Devis Contact
TS924IDT - Quad Rail-to-Rail Op Amp, 4 MHz | STMicroelectronics
TS924IDT

TS924IDT - Quad Rail-to-Rail Op Amp, 4 MHz | STMicroelectronics

The STMicroelectronics TS924IDT is a quad, rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with four amplifiers housed in a 14-pin Small Outline package. Key specifications include a 4 MHz gain-bandwidth product, 1.3 V/µs slew rate, and a 2.7 V to 12 V supply-voltage range. An operational amplifier is an active analog signal-conditioning device that amplifies the voltage difference between its inverting and non-inverting inputs. The TS924 belongs to the quad operational-amplifier family, placing four amplifiers in one package to reduce component count in multi-channel instrumentation. Its rail-to-rail input and output architecture supports low-voltage signal chains in which the usable common-mode and output ranges extend close to the supply rails. The BiCMOS construction combines bipolar input transistors with CMOS output stages. In the TS924, this architecture supports low input-bias current of 15 nA, a 4 MHz unity-gain bandwidth, and 1.3 V/µs slew rate. The device is specified for both 3 V and 5 V systems and operates across a supply range of 2.7 V to 12 V. The operating temperature range extends from -40 °C to +125 °C. Typical applications include current-to-voltage conversion in precision measurement systems, sensor-signal conditioning, low-voltage audio circuits, active filtering, and general-purpose analog signal conditioning. Because four matched amplifier channels share one package, designers can also use the device for dual-rail control loops, quad sensor interfaces, and multi-axis signal acquisition. When laying out a TS924IDT circuit, place each decoupling capacitor close to its corresponding supply pin and keep feedback resistors and input traces short to minimize parasitic capacitance. Verify the input common-mode range, output-current capability, and capacitive-load stability against the load connected to each amplifier. The SO-14 outline is suitable for conventional surface-mount assembly and supports design reuse across the STMicroelectronics TS92x family. This page consolidates the manufacturer specifications, package and lifecycle information, price references, cross-reference findings, and practical design guidance into one engineering-focused resource for evaluating the TS924IDT in new analog designs.

Devis Contact
TS924IN - Quad 4MHz Rail-to-Rail Op Amp | STMicroelectronics
TS924IN

TS924IN - Quad 4MHz Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS924IN is a quad, rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with four amplifier channels, 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and low input-offset voltage up to 900 uV. The device is supplied in a 14-pin DIP package, making it suitable for conventional through-hole and legacy industrial designs. An operational amplifier is a high-gain analog signal-conditioning IC used in the broader voltage-amplifier and analog IC hierarchy. The TS924IN combines four independent amplifiers in one package, allowing compact implementation of filters, amplifiers, comparators, instrumentation circuits, and signal-conditioning stages. Its rail-to-rail output design supports operation close to the supply rails, while its BiCMOS construction combines bipolar input characteristics with CMOS output stages. The headline specifications are 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and input offset voltage of 900 uV maximum. The TS924 family is fully specified for 3 V and 5 V supply operation, and the supplied operating-range information extends to 12 V. Its high output-current capability is particularly useful for driving low-impedance loads compared with many general-purpose op-amplifier choices. Each channel can operate as an amplifier, comparator, or active-filter building block. The wide available bandwidth supports signal paths that need more gain-bandwidth than low-speed precision-oriented amplifiers, while the 1.3 V/us slew rate allows moderate-amplitude signals to transition without excessive distortion. Four integrated channels can reduce package count and simplify board layout in multi-channel measurement and control systems. Typical uses include industrial sensor interfaces, low-voltage audio and communication circuits, active filters, data-acquisition front ends, process-control loops, and general-purpose analog signal conditioning. The 14-DIP format is especially useful when maintaining an existing through-hole design or avoiding a conversion to a surface-mount footprint. Input and output protection should still be considered because the verified data does not establish the maximum input or output voltage range. The principal design consideration is the power relationship between supply voltage, output swing, load current, and dissipation. Because no thermal-resistance or absolute maximum-rating data was included in the verified results, those values must be confirmed in the manufacturer datasheet before production release. Decoupling capacitors should be placed close to the supply pins and return pins should follow a low-impedance layout. This product record combines verified manufacturer and distributor information, package-specific replacement guidance, practical design considerations, and a parameter comparison that helps engineers distinguish true pin-compatible alternatives from merely functional substitutes. It supports component selection for legacy 14-DIP analog designs without treating incompatible package or performance variants as drop-in replacements.

Devis Contact
TS924IPT - Quad Rail-to-Rail Op Amp | STMicroelectronics
TS924IPT

TS924IPT - Quad Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS924IPT is a four-circuit, rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, supplied in a 14-pin TSSOP package. It combines rail-to-rail input and output capability with high output current, low noise, low distortion, and low offset. These characteristics position it as a general-purpose amplifier for low-voltage signal conditioning, audio, sensor interfaces, and portable equipment. An operational amplifier is a voltage-gain building block used to amplify small signals, buffer voltage sources, compare analog levels, and drive external circuits. The TS924 belongs to the BiCMOS operational-amplifier family, combining bipolar input circuitry with CMOS output stages. Rail-to-rail operation allows the amplifier to process input and output signals near the limits of its supply voltage, making it useful when the usable signal range is narrow. The four amplifiers in one package support space-efficient analog designs requiring multiple gain stages or buffered channels. Operation is optimized for both 3 V and 5 V systems, covering common low-voltage rails found in portable electronics, industrial controls, audio equipment, and embedded systems. Rail-to-rail output swing and high output-current capability also help the device accommodate heavier loads than a general low-power amplifier. The TS924 family is characterized by low noise, low distortion, and low offset, supporting accurate amplification of low-level signals. These characteristics matter in audio paths where distortion limits perceived fidelity, in sensor interfaces where small voltage changes must be preserved, and in control systems where offset can shift a measurement or threshold. The quad configuration also reduces component count and simplifies board-space allocation. Typical uses include headphone and line-level audio buffers, microphone preamplification, low-voltage sensor conditioning, active filtering, voltage followers, and low-level comparator functions. In each case, the four independent amplifier sections can implement parallel channels or several stages within the same subsystem. Designers should confirm output-current demand, load impedance, stability, and input/output common-mode limits against the manufacturer datasheet for the selected operating condition. A key design consideration is power-supply decoupling and careful handling of capacitive loads. Place the input and output bypass capacitors close to their associated pins, keep sensitive input traces short, and account for the amplifier's behavior when driving resistive or capacitive loads. The datasheet pin description and recommended application circuit should guide the final layout. This page combines the TS924 family's operating characteristics with application guidance, design cautions, and a structured comparison of identified drop-in candidates. It is intended to help engineers evaluate the TS924IPT for 3 V and 5 V analog systems before implementing the 14-pin TSSOP footprint on a PCB.

Devis Contact
TS925ID - Quad 4MHz Rail-to-Rail Op Amp | STMicroelectronics
TS925ID

TS925ID - Quad 4MHz Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS925ID is a quad operational amplifier with rail-to-rail input and output capability, 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and operation from 2.7 V to 12 V in a 16-pin SOIC package. Each amplifier can deliver 80 mA of output current, allowing it to drive up to 32 loads according to the manufacturer documentation. An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify voltage differences between two inputs. The TS925ID belongs to the operational-amplifier hierarchy and combines four amplifiers in one package. Rail-to-rail input behavior supports operation near the positive and negative supply rails, while rail-to-rail output behavior provides greater output-voltage range than conventional amplifiers constrained by the supply rails. The principal features include 9 nV/Hz input-voltage noise, low distortion, 4 MHz bandwidth, and 1.3 V/us slew rate. The 80 mA output-current capability distinguishes the TS925ID from lower-current general-purpose op amps, making it useful where several amplifiers must drive heavier resistive or capacitive loads. Its quad configuration also reduces board area by integrating four amplifier channels. The TS925ID combines bipolar input and CMOS output stages, identified in technical listings as a BiCMOS amplifier. This architecture supports rail-to-rail operation while retaining low-noise bipolar input characteristics. Because the four channels share a common package, careful consideration of power-supply routing, grounding, output isolation, and thermal behavior is required in multi-channel analog systems. Typical uses include audio output stages, active filters, sensor-conditioning circuits, buffer amplifiers, communications receivers, and industrial control systems. Its quad organization is particularly useful when a design needs four closely related analog channels. The adjustable phantom-ground feature can support signal references in applications requiring an artificial ground, while the standby mode can reduce power consumption when the amplifier is not needed. Designers should use the manufacturer datasheet to verify the complete electrical limits, pin configuration, output-current conditions, stability requirements, and recommended external components. Decoupling capacitors should be placed close to the supply pins, and outputs that drive capacitive loads may require isolation resistors or other stability measures. Because the available verified specification excerpt does not provide the complete pin table, the package diagram should not be used as a substitute for the official datasheet. This page consolidates the verified TS925ID operating range, bandwidth, slew rate, noise, output-current, package, pricing, and sourcing information into an engineering-focused reference. It also distinguishes verified same-package alternatives from parts that require package or electrical revalidation, helping designers make a safer replacement decision before committing a new PCB layout.

Devis Contact
TS925IDT - Quad 80mA Rail-to-Rail Op Amp | STMicroelectronics
TS925IDT

TS925IDT - Quad 80mA Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS925IDT is a four-circuit, rail-to-rail input and output operational amplifier optimized for 3 V and 5 V operation, with an operating supply range extending to 12 V. The device provides a 4 MHz gain-bandwidth product, 1.3 V/us slew rate, 9 nV/Hz input noise, and up to 80 mA of output drive current in an SOIC-16 package. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. A rail-to-rail input and output amplifier can operate with input and output voltages close to either supply rail, making it useful in battery-powered, portable, and mixed-signal equipment. The TS925 belongs to the general-purpose operational amplifier family within the broader analog and linear IC hierarchy. The TS925IDT combines four amplifiers in one package with several features aimed at portable instrumentation. Its rail-to-rail input stage accepts signals across nearly the full supply range, while rail-to-rail output swing supports low-impedance loads. High output current of 80 mA can drive up to 32 loads according to the manufacturer documentation. The 4 MHz bandwidth and 1.3 V/us slew rate improve response speed in audio, sensor, and control paths. The TS925 also includes standby mode and an adjustable phantom-ground arrangement. The internal low-impedance phantom ground can simplify biasing and eliminate the need for an external reference voltage or bias network in suitable applications. The four amplifiers share one package while retaining independent input and output pins, allowing one component to implement four analog functions. Typical applications include portable audio and headphone stages, low-voltage sensor conditioning, current measurement, industrial control, and general-purpose instrumentation. The 80 mA output capability is particularly useful when the amplifier must drive heavier loads than a conventional low-power quad amplifier can support. The SOIC-16 package also simplifies assembly and provides adequate pin spacing for production test and inspection. When designing around the TS925IDT, verify input common-mode range and output swing for the actual load current because rail-to-rail operation does not guarantee perfect saturation at the supply rails. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer's recommended stable input arrangement rather than left floating. This page combines the TS925IDT operating characteristics with same-package family alternatives, application guidance, comparison parameters, and practical layout notes. These engineering-oriented details help shorten component selection and support design decisions that are not visible in a basic distributor catalog listing.

Devis Contact
TS925IN - Quad Rail-to-Rail Op Amp, 4 MHz | STMicroelectronics
TS925IN

TS925IN - Quad Rail-to-Rail Op Amp, 4 MHz | STMicroelectronics

STMicroelectronics TS925IN is a four-circuit, general-purpose operational amplifier with rail-to-rail input and output capability, 4 MHz gain-bandwidth performance, standby mode, and an adjustable phantom-ground function. The device is packaged in a 16-DIP package measuring 0.300 inches, or 7.62 mm, across the row spacing. Its four amplifiers are intended for compact analog signal-conditioning systems where multiple buffered or amplified channels are required. An operational amplifier is an active analog semiconductor that uses high open-loop gain to amplify the difference between two input voltages. The TS925IN belongs to the general-purpose operational-amplifier family within the broader amplifier and analog IC hierarchy. Rail-to-rail input and output behavior allows the amplifier to operate across a substantial portion of its supply range, while the four-circuit arrangement consolidates four amplifier channels into one package. These characteristics make the device suitable for sensor interfaces, audio paths, instrumentation, and control-system signal chains. The main features of the TS925IN include four amplifier sections, a 4 MHz gain-bandwidth product, rail-to-rail operation, high output-current capability, standby mode, and an adjustable phantom-ground arrangement. Standby support can reduce active power consumption when signal handling is not required. The adjustable phantom-ground function can provide an internal reference point for noninverting amplifier configurations, which can simplify some gain-stage layouts and reduce the number of external reference components. The TS925IN is designed for general-purpose analog amplification rather than precision measurement or specialized high-voltage operation. Its four integrated channels can reduce board area compared with separate single or dual amplifier packages. Design engineers must still account for input common-mode range, output swing, supply voltage, stability, output-current demand, and the effect of the phantom-ground network when assigning signal levels. Because the accessible product records do not expose the complete electrical-limit table, exact slew rate, input bias current, output-current limit, and temperature limits should be confirmed in the manufacturer datasheet before release. Typical uses include four-channel sensor buffering, low-frequency audio amplification, industrial measurement interfaces, analog control loops, and general instrumentation. The 16-DIP package is appropriate for through-hole designs where insertion and inspection are important, although it occupies more PCB area than comparable surface-mount packages. The four-channel architecture is especially useful when four channels must be amplified consistently and nearby to the source or destination circuitry. A practical design choice is to keep feedback resistors close to the relevant amplifier pins, route high-impedance input traces away from switching nodes, and decouple each supply rail near the package. Confirm that the required output amplitude remains inside the usable output swing. For systems using standby or phantom ground, verify startup, shutdown, and settling behavior in the final signal-chain configuration rather than treating those features as isolated block-level functions. This page consolidates the verified product identity, package information, functional characteristics, sourcing workflow, replacement constraints, and application guidance for the TS925IN. It also distinguishes documented drop-in substitutes from differently packaged family members, helping engineers avoid assuming that a similar amplifier description guarantees footprint, pin, or electrical compatibility.

Devis Contact
TS925IPT - Quad Rail-to-Rail Op Amp | STMicroelectronics
TS925IPT

TS925IPT - Quad Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS925IPT is a four-circuit rail-to-rail operational amplifier with standby mode, adjustable phantom ground, a 3 V supply class, and a 4 MHz gain-bandwidth product, packaged in a 16-pin TSSOP. The quad topology integrates four amplifier channels into one package, making the device useful in signal-conditioning systems that need multiple buffered inputs without allocating separate packages for each channel. Its standby function supports power management in portable and mixed-signal equipment, while the adjustable phantom ground provides a reference point for single-supply signal chains. A rail-to-rail operational amplifier is an amplifier whose output stage can approach both supply rails under suitable load conditions. This input and output flexibility makes the TS925IPT suitable for low-voltage systems in which signals may occupy much of the available supply range. Operational amplifiers are voltage-amplifier building blocks within analog and mixed-signal ICs, connecting sensor outputs, reference voltages, audio signals, and control signals to subsequent processing stages. The TS925IPT provides four rail-to-rail amplifier circuits, 4 MHz gain-bandwidth performance, standby-mode control, and an adjustable phantom-ground function in one 16-pin TSSOP package. Its rail-to-rail architecture reduces the need to bias signals away from either supply rail, while the quad channel count reduces component count and PCB area in multi-channel analog front ends. Standby operation can lower system activity when the monitored signal does not require continuous amplification. The 3 V supply class and 4 MHz gain-bandwidth product place the device between general-purpose low-voltage amplifiers and much higher-speed signal-chain devices. A 4 MHz bandwidth is suitable for audio-range and general instrumentation signals rather than high-frequency communications or precision measurement requiring bandwidths in the tens or hundreds of megahertz. The adjustable phantom ground is especially relevant to systems that establish an artificial reference for AC-coupled or biased signals. Typical uses include four-channel sensor conditioning, low-voltage audio amplification, joystick or potentiometer interfaces, industrial control inputs, and instrumentation requiring independent gain or buffer stages. The standby feature can also support duty-cycled acquisition systems, while the phantom-ground connection can simplify biasing around an intermediate reference voltage. The package is suitable for compact surface-mounted boards but requires careful attention to grounding and decoupling near the supply pins. Design with the manufacturer’s recommended application circuit and pin-description table. Place the power-supply bypass capacitor close to the supply pins, route each amplifier’s input and output away from switching-node traces, and connect the phantom-ground network only as shown in the datasheet. Verify the complete operating range, load capability, output swing, and shutdown behavior for the intended supply voltage before production release. This product page combines the TS925IPT’s key technical identity with practical guidance on standby control, phantom-ground implementation, package layout, and design trade-offs. It also organizes pinout, application, compliance, and replacement information so engineers can move directly from component selection to PCB-level implementation.

Devis Contact
TS931AID - 100kHz Rail-to-Rail Output Op Amp, SOIC-8 | STMicroelectronics
TS931AID

TS931AID - 100kHz Rail-to-Rail Output Op Amp, SOIC-8 | STMicroelectronics

The STMicroelectronics TS931AID is a single, low-power operational amplifier with rail-to-rail output swing in an 8-pin SOIC (SOP) package, specified for industrial temperature grade. The device belongs to the TS93x family of micropower operational amplifiers, which operate from supplies as low as 2.7 V and reach a 2.9 Vpp output swing with a 100 kOhm load when supplied at 3 V. Its unity-gain bandwidth of 100 kHz makes it a general-purpose amplifier for low-frequency signal conditioning rather than a high-speed precision part. An operational amplifier (op amp) is a differential-input voltage amplifier whose gain is set by external feedback components. A rail-to-rail (RRO) output amplifier can swing its output close to both supply rails, so the output remains useful even when the signal approaches the supply limits. In the classification hierarchy, the TS931AID is an operational amplifier, which is a type of amplifier IC, which falls under integrated circuits and analog signal conditioning. Micro-power rail-to-rail op amps occupy the intersection of battery-powered sensing, portable instrumentation, and low-leakage buffer applications. Key differentiating features of the TS931AID include rail-to-rail output operation, operation from a 2.7 V minimum supply, a 100 kHz unity-gain bandwidth, an 8-pin SOIC footprint with gull-wing leads, and industrial temperature grading. Because output swing reaches 2.9 Vpp at 3 V supply with a light 100 kOhm load, the part is a good fit for buffered sensor front-ends and low-voltage signal chains where headroom is tight. Note that the TS931AID is characterized for output rail-to-rail behaviour; input common-mode range figures should be confirmed against the manufacturer datasheet before committing to a design that relies on input operation near the rails. Technically, the TS931AID is a single-amplifier device in the TS93x line, which also includes dual and quad members. The 100 kHz gain-bandwidth product places the part firmly in the micropower/general-purpose segment rather than the precision or high-speed segments, meaning it is intended for signal conditioning, buffering, and level shifting where bandwidth requirements are modest but power consumption and rail-to-rail reach matter more. Typical applications include battery-powered sensor conditioning in industrial and medical monitoring equipment, low-voltage audio and communication signal buffering, and post-processing stages in data acquisition systems. Because the family supports supply voltages down to 2.7 V, it pairs well with coin cells, single Li-ion cells, and low-voltage energy-harvesting front-ends. When designing with the TS931AID, keep the output load within the range used for the quoted 2.9 Vpp swing figure and place a decoupling capacitor close to the supply pins. Verify the input common-mode range and output swing under load in the manufacturer datasheet, and check the noise and offset specifications against your signal-chain budget before committing the design. This page consolidates distributor sourcing data, pin-compatible drop-in alternatives, a parameter-by-parameter comparison table, and practical design guidance for the TS931AID that you will not find in a single manufacturer datasheet page.

Devis Contact
TS931BID - Micropower Rail-to-Rail Op Amp | STMicroelectronics
TS931BID

TS931BID - Micropower Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS931BID is a single-circuit, micropower, rail-to-rail operational amplifier with a 2.7 V to 10 V supply range, packaged in an 8-pin SOIC. It is designed for general-purpose signal conditioning where low power consumption, rail-to-rail output capability, and operation from low-voltage supplies are important. The TS931BID combines a listed quiescent current of 0.0003 uA, input bias current of 1 pA, and a gain-bandwidth product of 100 kHz. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs. The rail-to-rail output architecture allows the output signal to approach the supply rails more closely than a conventional amplifier with limited output swing. This makes the TS931BID useful for portable instruments, battery-powered sensors, low-voltage industrial controls, and other embedded systems that require amplification without a high-power supply. Key characteristics include one amplifier circuit, rail-to-rail output operation, a 2.7 V minimum supply voltage, and a 10 V maximum supply voltage. The low 0.0003 uA quiescent-current figure supports energy-conscious designs, while the 1 pA input-bias-current specification reduces input-loading effects in high-impedance measurement paths. A listed 55 dB gain-bandwidth-related figure and 100 kHz bandwidth suit low-to-moderate-frequency precision signal applications. The TS931BID belongs to the STMicroelectronics TS931 family of low-power operational amplifiers. Its 8-SOIC package supports conventional surface-mount assembly and provides a practical option for designs requiring a single amplifier in a small, standard package. Because the device operates from a 2.7 V supply, system-level signal ranges should be checked against the input common-mode and output-swing limits in the manufacturer datasheet. Typical uses include low-voltage sensor interfaces, portable measurement equipment, battery-operated data-acquisition modules, industrial process monitoring, and embedded control systems. In a sensor interface, the amplifier can increase the usable signal level before an ADC samples it. In a portable instrument, its low quiescent current helps limit standby consumption. The relatively modest 100 kHz bandwidth favors precision and low-frequency measurements rather than high-speed signal processing. PCB design should place input and feedback components close to the amplifier pins and maintain short, low-impedance traces to reduce noise pickup and parasitic feedback. Decoupling capacitors should connect directly between the supply and ground pins. Before substituting the TS931BID, verify supply voltage, input common-mode range, output swing, stability with the selected load capacitance, noise performance, and the exact pin assignment. This page combines the identified TS931BID electrical characteristics, package information, sourcing context, and practical design guidance. It also organizes same-family alternatives and a parameter comparison to help engineers determine whether the device fits the required footprint, voltage range, bandwidth, and power budget.

Devis Contact