ATSAMD21E18A-MF vs ATSAMD21-XPRO Comparaison
Comparaison détaillée côte à côte de ATSAMD21E18A-MF par Microchip Technology et ATSAMD21-XPRO par Microchip Technology. Comparez les spécifications clés, les paramètres électriques, le conditionnement, le statut de cycle de vie, les prix et la disponibilité pour déterminer le meilleur composant pour vos exigences de conception.
Microchip Technology
ATSAMD21E18A-MF - 256KB Flash ARM Cortex-M0+ MCU | Microchip
ATSAMD21E18A-MF ✓ ActifMicrochip Technology
ATSAMD21-XPRO - SAM D21 Xplained Pro ARM Cortex-M0+ Eval Board
ATSAMD21-XPRO ✓ ActifComparaison des spécifications
| Paramètre | ATSAMD21E18A-MF | ATSAMD21-XPRO |
|---|---|---|
| Marque | Microchip Technology | Microchip Technology |
| Catégorie | Microcontrollers | Development Boards |
| Statut du cycle de vie | Actif | Actif |
| Statut du stock | In Stock | In Stock |
| Prix unitaire (USD) | $6,95 | $36,25 |
| Core Architecture | ARM Cortex-M0+ (32-bit) | — |
| Series | SAM D21E | — |
| Fréquence d'horloge maximale | 48 MHz | — |
| Flash Memory | 256 KB | — |
| SRAM | 32 KB | 32 KB |
| Operating Voltage Range | 1.6 V to 3.6 V | — |
| Plage de température de fonctionnement | -40C to +125C | — |
| Boîtier | 32-pin QFN (5x5 mm) | — |
| CoreMark Performance | 2.46 CoreMark/MHz | — |
| ADC | 12-bit, up to 20 channels | — |
| DAC | 10-bit | — |
| USB | USB 2.0 Full-Speed Device | — |
| SERCOM Interfaces | 6 configurable (I2C/SPI/UART) | — |
| DMAC Channels | 6 | — |
| Peripheral Touch Controller (PTC) | Yes | — |
| Statut RoHS | Compliant | Compliant |
| Type de montage | Surface Mount | — |
| Product Type | — | Evaluation Board (Xplained Pro) |
| Target MCU | — | ATSAMD21J18A |
| Core Processor | — | ARM Cortex-M0+ 32-bit |
| CPU Max Frequency | — | 48 MHz |
| Flash Memory (on-chip) | — | 256 KB |
| On-board SPI Flash | — | 1 MB |
| Low-frequency Crystal | — | 32.768 kHz |
| High-frequency Crystal | — | 12 MHz |
| Debug Interface | — | nEDBG (CMSIS-DAP) on-board |
| USB Connectors | — | 1x Micro-B (debug/CDC), 1x Micro-B (target) |
| Extension Headers | — | 3x 20-pin Xplained Pro (compatible with I/O1, OLED1, QT1, PROTO1) |
| User Inputs | — | 1x mechanical reset button, 1x user touch button |
| User Outputs | — | 1x user LED |
| Arduino-compatible Headers | — | Yes (subset of ATSAMD21J18A I/O) |
| Operating Voltage (target) | — | 3.3 V |
| Board Power Source | — | USB Micro-B |
| Supported IDEs | — | MPLAB X IDE, Atmel Studio 7, Atmel START |
| Form Factor | — | Xplained Pro standard (approx 88 mm x 53 mm) |