AD8011ANZ - 328MHz Low-Power Current Feedback Amp | Analog Devices
Référence : AD8011ANZ ✓ ActifAD8011ANZ Présentation
A current-feedback amplifier is a voltage-feedback amplifier architecture whose bandwidth and stability behavior are strongly influenced by feedback impedance rather than by a fixed closed-loop gain bandwidth. This architecture is widely used for video, instrumentation, signal-conditioning, and communications applications where high-speed operation and predictable gain-bandwidth behavior are more important than unity-gain stability. The AD8011 is therefore positioned between general-purpose precision amplifiers and very-high-power RF amplifiers.
The AD8011ANZ operates from +5 V or ±5 V supplies and is designed around a current-feedback topology for high-speed signal amplification. Its key strengths include wide bandwidth, low distortion, and very low power consumption. The 8-PDIP package provides through-hole assembly compatibility for industrial, instrumentation, and legacy equipment designs. The manufacturer describes the device as a general-purpose amplifier and as a possible replacement for high-speed amplifiers that consume more power.
The AD8011 is appropriate for video signal paths, instrumentation amplifiers, communication interfaces, analog front ends, and other applications requiring high-frequency amplification. Because current-feedback amplifiers depend on feedback-component selection, engineers should use the resistor and capacitor values recommended in the manufacturer datasheet rather than transplanting feedback networks from unrelated amplifier families.
For PCB implementation, keep feedback-loop connections short and place the input, output, feedback, and decoupling connections with attention to high-current return paths. The AD8011ANZ is a through-hole device, so its package requires adequate board spacing, pin-clearance planning, and mechanical verification against the target enclosure and connector layout.
This product page combines manufacturer application information, distributor package confirmation, lifecycle context, drop-in alternatives, and practical design guidance to support component selection, board layout, and sourcing decisions.
Alternatives de remplacement direct pour AD8011ANZ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
AD8011AN
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AD8011ANC
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AD8012
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AD8013
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AD8014
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AD8011ANZ Valeurs maximales et caractéristiques électriques
| Amplifier Type | Current Feedback Amplifier |
| Number of Circuits | 1 circuit |
| Tension d'alimentation | +5 V or ±5 V |
| Boîtier | 8-PDIP |
| Topologie | Current feedback |
| Gain Flatness | 0.1 dB to 25 MHz |
| Bandwidth | 328 MHz |
| Power Consumption | Very low power |
| Signal Type | Single-ended |
| Type de montage | Through-hole |
| Statut RoHS | RoHS-compliant |
| Lead-Free Status | Lead-free |
| Green Packaging | Green electronic component |
Guide de configuration des broches du AD8011ANZ 8-pdip
Configuration des broches du AD8011ANZ (boîtier 8-pdip). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour AD8011ANZ.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
AD8011ANZ convient pour 6 applications: High-Speed Video Signal Conditioning, Instrumentation and Sensor Front Ends, Communications Receive Chains, Analog-to-Digital Converter Drive, Low-Power Instrumentation Signal Buffers, Pulse and Transient Signal Conditioning.
High-Speed Video Signal Conditioning
The AD8011ANZ is well suited to video signal-conditioning stages that require wide bandwidth and low power consumption from a +5 V or ±5 V supply. Its current-feedback architecture and 0.1 dB gain-flatness specification to 25 MHz provide the bandwidth needed to preserve fast video edges, while the manufacturer describes the device as a low-power high-speed video amplifier. Place the AD8011 near the video source or receiving buffer, use the recommended feedback resistor for the intended gain, and keep the feedback trace short. Verify output settling and distortion in the target video format because source impedance, cable loading, and the next-stage input capacitance can materially affect the practical response.
Recommandé
Instrumentation and Sensor Front Ends
The AD8011ANZ can serve as the first high-speed gain stage in an instrumentation or sensor front end when the sensor produces a fast analog waveform that must be conditioned before digitization. The 328 MHz bandwidth figure and 0.1 dB gain-flatness specification to 25 MHz make the device relevant to wideband measurement chains, while its very-low-power bias reduces the burden on portable or distributed acquisition systems. Use the manufacturer's recommended feedback network for the selected gain, terminate the source impedance correctly, and place supply-bypass capacitors close to the device. Check input common-mode range, output swing, and offset behavior against the sensor's operating range.
Recommandé
Communications Receive Chains
The AD8011ANZ is appropriate for low-power amplification within communications receive chains where a high-speed analog stage must operate before filtering, conversion, or demodulation. Its current-feedback topology supports wide bandwidth, and the manufacturer identifies the device as a general-purpose high-speed amplifier with low power consumption and low distortion. In a practical receiver, the amplifier can add gain close to the connector or antenna interface, reducing the amount of unwanted loss before subsequent filtering. Keep the input path and feedback loop compact, verify the return path against ground, and confirm the output drive against the next stage's impedance and capacitance.
Recommandé
Analog-to-Digital Converter Drive
The AD8011ANZ can provide the high-speed drive stage immediately preceding an ADC when the converter's sampling edge requires more bandwidth or lower distortion than a general-purpose op amp can deliver. Its 328 MHz bandwidth and gain flatness to 25 MHz allow the stage to preserve fast transitions, while the +5 V or ±5 V supply options simplify integration into mixed-signal equipment. Select the gain and feedback components from the manufacturer's ADC-driving guidance, place the amplifier close to the ADC input, and use a controlled return path to minimize clock and digital crosstalk. Validate settling, common-mode level, and output compliance against the ADC data sheet.
Recommandé
Low-Power Instrumentation Signal Buffers
The AD8011ANZ can replace a higher-power high-speed amplifier in instrumentation buffers where the system has a restricted supply budget but still requires wide bandwidth. Analog Devices specifically describes the AD8011 as a possible replacement for high-speed amplifiers consuming more power, which makes it relevant to portable measurement systems and compact laboratory equipment. The 8-PDIP package supports straightforward through-hole assembly and rework in legacy or industrial instruments. Use the recommended current-feedback network, preserve the manufacturer's recommended ground and bypass arrangement, and validate that the lower-power device still meets the required output swing, noise, and stability margins.
Recommandé
Pulse and Transient Signal Conditioning
The AD8011ANZ is useful for amplifying short-duration pulses and fast transient signals where bandwidth determines whether the system preserves pulse edges. Its wide-band current-feedback architecture, combined with the manufacturer description of low distortion and very low power consumption, makes it a candidate for radar, test and measurement, and industrial pulse-processing circuits. The amplifier should be placed near the source to limit trace loss, with the feedback loop kept as short as possible. Verify rise time, overshoot, and settling with the actual source and load because the gain-bandwidth relationship of a current-feedback amplifier depends directly on the selected feedback impedance.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour AD8011ANZ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | AD8011AN | AD8011ANC | AD8012 | AD8013 | AD8014 |
|---|---|---|---|---|---|---|
| Package | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Architecture | Current Feedback Amplifier | Current Feedback Amplifier | Current Feedback Amplifier | Current Feedback Amplifier | Current Feedback Amplifier | Current Feedback Amplifier |
Principaux différenciateurs
- Lower-power current-feedback amplification option (vs AD8012)
- Direct AD8011 family ordering continuity (vs AD8013)
- Gain-flat performance for fast video and analog paths (vs AD8014)
Notes de conception
Do not treat a current-feedback amplifier like a unity-gain-stable voltage-feedback amplifier. The AD8011ANZ bandwidth and stability depend on the feedback impedance, so the feedback resistor and compensation capacitor must come from the manufacturer datasheet. Copying a feedback network from another amplifier can create peaking or instability even when the intended gain is identical.
Keep the forward and feedback paths physically short and connect the bypass capacitors directly to the supply and ground pins. High-frequency current should not flow through long traces or shared ground paths between the input, output, and feedback components. After layout, verify the implemented gain, peaking, settling, and output drive with the actual source and load rather than relying only on simulation.
Use the +5 V or ±5 V supply arrangement intended by the application and follow the manufacturer bypass recommendations. Because the AD8011 is specifically positioned as a lower-power replacement for higher-consumption high-speed amplifiers, power-supply capacity should still be checked for the configured supply voltage, output load, and board temperature. Avoid adding excessive decoupling capacitance directly across the supply pins, which can impair stability in some high-speed amplifier layouts.
Informations de conformité
RoHS-compliant, lead-free, and green status is stated in distributor product documentation for AD8011ANZ. Automotive qualification, REACH status, halogen-free status, and conflict-minerals declarations require separate confirmation from the current manufacturer documentation.