AD8418WBRZ-RL - 20V/V Bidirectional Zero-Drift Current Sense Amp | ADI
Référence : AD8418WBRZ-RL ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $1.86 | $1,86 |
| 10 | $1.7 | $17,00 |
| 100 | $1.21 | $121,00 |
| 500 | $1.1 | $550,00 |
| 1 000 | $0.98 | $980,00 |
AD8418WBRZ-RL Présentation
A current sense amplifier is a specialized instrumentation amplifier that amplifies the small voltage drop across a shunt resistor to measure load current precisely. It sits within the amplifier IC family, under analog signal conditioning ICs. The AD8418 belongs to the zero-drift amplifier class, which uses chopper stabilization to eliminate offset voltage and drift - a key requirement in closed-loop current control systems where long-term accuracy is essential.
Key features include a 250 kHz bandwidth, a supply current of only 4.1 mA typical, and an internally fixed gain that removes the need for external gain-setting resistors. The zero-drift architecture achieves a maximum offset of ±50 µV (10 µV typical) and a gain drift of ±1 ppm/°C across -40°C to +125°C, while the output stage swings within 50 mV of the rails to maximize dynamic range.
Technically, the AD8418 uses a chopper-stabilized input stage, and its reference pins allow output level shifting for bidirectional current measurement on a single supply. This flexibility supports both unidirectional and bidirectional sensing topologies without negative supplies.
Typical applications include automotive motor control, solenoid control, battery management, and power supply monitoring, where the wide common-mode range and AEC-Q100 qualification ensure reliable operation in harsh environments.
Design tip: drive the reference pins from a low-impedance source and use short shunt traces with proper supply decoupling to avoid gain errors and noise pickup.
Alternatives de remplacement direct pour AD8418WBRZ-RL — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
AD8418WBRZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AD8418BRZ-RL
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AD8418BRZ
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
INA282BID
⚡ Même boîtier ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
AD8418WBRZ-RL Valeurs maximales et caractéristiques électriques
| Amplifier Type | Bidirectional zero-drift current sense amplifier |
| Canaux | 1 |
| Gain | 20 V/V (fixed) |
| Gain Error | ±0.15% max over temperature |
| Common-Mode Voltage Range | -2 V to +70 V |
| Supply Voltage Range | 2.75 V to 5.5 V |
| Bandwidth | 250 kHz |
| Offset Voltage | ±50 µV max (10 µV typical) |
| Gain Drift | ±1 ppm/°C |
| Courant d'alimentation | 4.1 mA typical |
| Output Swing | Within 50 mV of rails |
| Température de fonctionnement | -40°C to +125°C |
| Boîtier | 8-lead SOIC |
| Type de montage | Surface Mount |
| Automotive Qualification | AEC-Q100 qualified |
| Packaging | Tape and Reel (-RL) |
| Statut RoHS | Compliant |
Guide de configuration des broches du AD8418WBRZ-RL 8-lead soic
Configuration des broches du AD8418WBRZ-RL (boîtier 8-lead soic). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour AD8418WBRZ-RL.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
AD8418WBRZ-RL convient pour 6 applications: Automotive Motor Control Current Sensing, Battery Management Systems, Solenoid and Actuator Control, Power Supply and DC Bus Monitoring, 48V Mild-Hybrid Systems, Industrial Process Control.
Automotive Motor Control Current Sensing
The AD8418WBRZ-RL fits automotive motor control because its -2V to +70V common-mode range tolerates 12V/24V bus transients and its ±0.15% gain error preserves torque-control accuracy in closed-loop FOC schemes. Placed across a shunt in the DC bus or low-side return with a 250 kHz bandwidth, it resolves current ripples for control loops well beyond typical PWM sampling rates, while AEC-Q100 qualification and -40°C to +125°C operation ensure reliability under hood.
Recommandé
Battery Management Systems
For BMS pack current monitoring, the AD8418WBRZ-RL's zero-drift offset of ±50 µV max allows accurate measurement with small shunts, minimizing power loss, while ±1 ppm/°C gain drift keeps coulomb-counting accurate over battery life. Its -2V common-mode floor captures charging and regenerative reverse currents on a single supply, and the 20 V/V gain conveniently maps shunt drops into a 5V ADC range without extra gain stages.
Recommandé
Solenoid and Actuator Control
Solenoid drivers benefit from the AD8418WBRZ-RL's ability to sense current in high-side configurations up to +70V common-mode, enabling diagnostics of shorted loads and open circuits in 24V industrial and automotive actuators. The 250 kHz bandwidth captures peak-and-hold current waveforms, and the fixed 20 V/V gain simplifies design with no external gain resistors to drift, keeping trip thresholds accurate across temperature.
Recommandé
Power Supply and DC Bus Monitoring
In telecom and industrial power supplies, the AD8418WBRZ-RL monitors DC bus current with high-side shunts, where its wide common-mode range survives bus transients that would damage conventional amplifiers. The 10 µV typical offset enables millivolt-level shunt drops to be measured accurately, reducing shunt dissipation, and the output can be level-shifted via the REF pins to match any downstream ADC input range.
Recommandé
48V Mild-Hybrid Systems
The AD8418WBRZ-RL's +70V absolute common-mode capability provides headroom for 48V mild-hybrid battery rails and their transient overshoot. Its zero-drift architecture maintains ±0.15% gain accuracy over the full -40°C to +125°C range, supporting accurate load-current reporting to vehicle control units. AEC-Q100 qualification and tape-and-reel supply make it suitable for high-volume automotive production environments.
Recommandé
Industrial Process Control
In industrial current-loop and actuator monitoring, the AD8418WBRZ-RL provides a single-supply analog front end with bidirectional sensing via its REF pins, allowing positive and negative current indication around a mid-scale reference. The 4.1 mA supply current suits multichannel systems, and the chopper-stabilized input eliminates offset drift that would otherwise require periodic field calibration of current thresholds.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour AD8418WBRZ-RL — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | AD8418WBRZ | AD8418BRZ-RL | INA282BID |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Texas Instruments |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC |
| Gain | 20 V/V | 20 V/V | 20 V/V | 50 V/V |
| Common-Mode Range | -2 V to +70 V | -2 V to +70 V | -2 V to +70 V | -14 V to +80 V |
| AEC-Q100 | Qualified (W grade) | Qualified (W grade) | Qualified | Not qualified (standard) |
| Lifecycle | NRND | NRND | NRND | Active |
Principaux différenciateurs
- Zero-drift accuracy with wide common-mode (vs INA282BID)
- Bidirectional sensing on a single supply (vs INA282BID)
- Package choice flexibility within family (vs AD8418WBRMZ-RL)
Notes de conception
Use a Kelvin-connected shunt: route the amplifier input traces directly to the shunt resistor pads, not to shared current-carrying copper. With a ±50 µV maximum offset, even 1 mΩ of extra trace resistance adds error at high currents. Keep the input loop short and symmetrical, and place a 0.1 µF decoupling capacitor within 2 mm of the VS pin per Analog Devices layout guidance in the AD8418 datasheet typical application section.
Drive the REF pins from a low-impedance source. Because the reference-to-output gain is 1 V/V, any noise or impedance on REF appears directly at the output; a simple resistor divider without buffering introduces both gain error and offset shift. For bidirectional sensing, buffer the mid-scale reference with an op amp such as the AD8628 or use a precision reference IC.
The AD8418 is listed as NRND - Analog Devices does not recommend it for new designs, so plan a second-source strategy. Also note the WBRZ grade is specified for -40°C to +125°C; lower grades may not meet automotive requirements. Do not exceed the +70V common-mode rating during load-dump events without verifying transient conditions against the datasheet absolute maximum ratings.
Informations de conformité
RoHS compliance per distributor listings; AEC-Q100 qualification for the W automotive grade per ADI product data. REACH and halogen-free status not stated in provided data.
