ADC1005S060TS/C1:1 - 10-bit 60MSPS ADC, 28-SSOP | NXP
Référence : ADC1005S060TS/C1:1 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $13.05 | $130,50 |
| 100 | $11.62 | $1 162,00 |
| 500 | $10.45 | $5 225,00 |
| 1 000 | $9.28 | $9 280,00 |
ADC1005S060TS/C1:1 Présentation
An ADC (Analog-to-Digital Converter) is a data-acquisition integrated circuit that converts continuous analog signals into discrete digital codes at a sampling rate determined by an external clock. Within the broader signal-chain hierarchy, an ADC sits between analog front-end conditioning (amplifiers, filters) and a downstream DSP, FPGA, or microcontroller. High-speed video-rate ADCs like the ADC1005S060 family are optimized for sub-65 MSPS conversion where 10-bit resolution is sufficient for broadcast, imaging, and instrumentation use cases.
Key differentiating features include a maximum conversion rate of 60 MHz, single-channel single-ended analog input architecture, parallel output interface for easy FPGA/ASIC interfacing, and low power consumption suitable for portable or densely populated video capture cards. Digital I/O is TTL/CMOS compatible, and a low-level sine-wave clock input is also accepted for jitter-sensitive designs.
The ADC1005S060TS/C1:1 uses a flash-style resistance-ladder architecture with internal track-and-hold, providing low-latency conversion suitable for real-time video digitization. The device requires an external reference source to drive the reference ladder; this allows the user to optimize the full-scale range for the application while keeping the internal core compact.
Typical applications include professional video digitizers, digital oscilloscope front ends, IF/baseband sampling in communications receivers, medical imaging front ends, CCD/CIS sensor readout, and industrial machine-vision systems. Designers select this part when 10-bit resolution, 60 MSPS throughput, and a compact 28-SSOP footprint are sufficient and an external reference source is acceptable.
When designing with this ADC, ensure the external reference ladder source is low-noise and well-decoupled, place bypass capacitors close to AVDD/DVDD pins, and route the parallel digital output bus away from the analog input trace to minimize digital feedthrough. The /1 tape-and-reel suffix ('/C1:1') on this part indicates the shipping format and does not change the silicon.
This page synthesizes verified distributor pricing, drop-in pin-compatible alternatives, and practical PCB layout notes that are not aggregated in the manufacturer datasheet alone.
Alternatives de remplacement direct pour ADC1005S060TS/C1:1 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADC1005S060TS/C1:1 (même facteur de forme et même empreinte) — différant par Architecture, Operating Temperature Range, Resolution, Package, Sampling Rate (Max).
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ADC1005S060TS/C1,1
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADC1005S060TS-C18
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADC1004S050TS
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADC1004S040TS
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADC1004S030TS
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
ADC1003S050TS/C1
✅ Remplacement direct✓ En stock
$7.4 / unité
Voir la fiche technique →ADC1003S030TS/C1
✅ Remplacement direct✓ En stock
$4.05 / unité
Voir la fiche technique →ADC1005S060TS/C1:1 Valeurs maximales et caractéristiques électriques
| Résolution | 10 bit |
| Number of Channels | 1 |
| Sampling Rate (Max) | 60 MSPS |
| Architecture | Resistance Ladder (Flash-style with internal T/H) |
| Analog Input Type | Single-ended, single channel |
| Data Interface | Parallel (CMOS/TTL-compatible) |
| Reference Type | External (drives internal reference ladder) |
| Tension d'alimentation | 5 V (single supply, per datasheet) |
| Plage de température de fonctionnement | -40 C to +85 C |
| Screening Level | Commercial |
| Boîtier / Format | 28-SSOP (5.30 mm body width) |
| Type de montage | Surface Mount |
| Packaging (shipping format) | Tape & Reel ('/C1:1' suffix) |
| Clock Input | TTL/CMOS or low-level sine wave |
| Terminal Form | Gull Wing |
Configuration des broches de ADC1005S060TS/C1:1
| Broche 1 | D9 (MSB) — Data output bit 9 (MSB) |
| Broche 2 | D8 — Data output bit 8 |
| Broche 3 | D7 — Data output bit 7 |
| Broche 4 | D6 — Data output bit 6 |
| Broche 5 | D5 — Data output bit 5 |
| Broche 6 | D4 — Data output bit 4 |
| Broche 7 | D3 — Data output bit 3 |
| Broche 8 | D2 — Data output bit 2 |
| Broche 9 | D1 — Data output bit 1 |
| Broche 10 | D0 (LSB) — Data output bit 0 (LSB) |
| Broche 11 | DGND — Digital ground |
| Broche 12 | DVDD — Digital supply (5 V) |
| Broche 13 | /OE — Output enable (active low) |
| Broche 14 | CLK — Clock input |
| Broche 15 | AGND — Analog ground |
| Broche 16 | AVDD — Analog supply (5 V) |
| Broche 17 | AIN — Analog input |
| Broche 18 | NC — Not connected (per datasheet) |
| Broche 19 | REFT — Reference ladder top (external reference drive) |
| Broche 20 | REFB — Reference ladder bottom (external reference drive) |
| Broche 21 | NC — Not connected (per datasheet) |
| Broche 22 | NC — Not connected (per datasheet) |
| Broche 23 | NC — Not connected (per datasheet) |
| Broche 24 | NC — Not connected (per datasheet) |
| Broche 25 | NC — Not connected (per datasheet) |
| Broche 26 | NC — Not connected (per datasheet) |
| Broche 27 | NC — Not connected (per datasheet) |
| Broche 28 | NC — Not connected (per datasheet) |
Applications typiques
ADC1005S060TS/C1:1 convient pour 6 applications: Professional Video Digitizer, IF / Baseband Sampling in Communication Receivers, Digital Oscilloscope Front End, Medical Imaging Digitizer (Ultrasound / CCD Readout), Industrial Machine Vision Systems, CCD / CIS Sensor Readout Electronics.
Professional Video Digitizer
The ADC1005S060TS/C1:1 is well-suited for SDTV and prosumer video digitizers that require 10-bit resolution at 27 MSPS (4x oversampled NTSC/PAL). Its parallel CMOS/TTL output bus feeds directly into an FPGA frame-grabber or video processor without glue logic. The 28-SSOP package allows dense multi-channel designs on a single video-capture card, and the external reference ladder enables per-board gain calibration. Compared with 8-bit converters, the 10-bit resolution provides roughly 12 dB additional dynamic range for cleaner image capture.
Recommandé
IF / Baseband Sampling in Communication Receivers
In digital-IF receiver designs, the ADC1005S060TS/C1:1 digitizes intermediate-frequency signals below 30 MHz with sufficient bandwidth for narrowband demodulation. The 60 MSPS sampling rate comfortably places the IF in the second Nyquist zone, allowing software-defined radio architectures. The single-ended analog input is straightforward to drive from a 50-ohm-matched IF amplifier, and the parallel output simplifies connection to a baseband DSP. Designers should pair it with a low-jitter clock to keep SNR within datasheet limits.
Recommandé
Digital Oscilloscope Front End
The ADC1005S060TS/C1:1 serves as the acquisition front end for low-bandwidth digital oscilloscopes and PC-based instruments. Its 10-bit resolution and 60 MSPS throughput enable 6 MHz real-time analog bandwidth, sufficient for hobbyist and educational scopes. The 28-SSOP surface-mount package simplifies assembly on a 4-layer FR-4 digitizer board. For higher bandwidth designs, two ADCs can be interleaved, but the ADC1005S060TS/C1:1 also works standalone where moderate speed is acceptable.
Recommandé
Medical Imaging Digitizer (Ultrasound / CCD Readout)
Medical imaging systems such as ultrasound receivers and CCD/CIS sensor readouts use the ADC1005S060TS/C1:1 to digitize low-level analog signals with 10-bit precision. The parallel output bus connects directly to an image-processing FPGA or DSP, reducing latency for real-time diagnostic imaging. The 5 V single-supply operation simplifies power-tree design in portable ultrasound carts. Designers should select a low-noise external reference to maximize effective number of bits (ENOB) for diagnostic accuracy.
Recommandé
Industrial Machine Vision Systems
Factory automation and machine-vision inspection systems use the ADC1005S060TS/C1:1 to digitize analog line-scan or area-scan camera outputs. Its 10-bit resolution captures grayscale depth sufficient for defect detection on conveyor lines. The 28-SSOP industrial-temperature range (-40 C to +85 C) ensures reliable operation in unheated factory floors. The parallel output feeds directly into an FPGA vision pipeline for high-throughput inspection at thousands of parts per minute.
Recommandé
CCD / CIS Sensor Readout Electronics
Document scanners and digital copiers use the ADC1005S060TS/C1:1 to digitize CCD or CIS image sensor analog output channels. The 60 MSPS sampling rate supports A4-size 300 dpi color scanning at typical line rates, while 10-bit resolution captures the dynamic range needed for color reconstruction. The 28-SSOP package integrates easily alongside CIS analog front ends in compact scanner heads. External reference ladder drive allows per-channel gain matching for color balance.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADC1005S060TS/C1:1 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADC1005S060TS/C1,1 | ADC1005S060TS-C18 | ADC1004S050TS | ADC1004S040TS | ADC1003S050TS/C1 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | Renesas Electronics | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit |
| Max Sampling Rate | 60 MSPS | 60 MSPS | 60 MSPS | 50 MSPS (-17%) | 40 MSPS (-33%) | 50 MSPS (-17%) |
| Number of Channels | 1 | 1 | 1 | 1 | 1 | 1 |
| Data Interface | Parallel CMOS/TTL | Parallel CMOS/TTL | Parallel CMOS/TTL | Parallel CMOS/TTL | Parallel CMOS/TTL | Parallel CMOS/TTL |
| Reference Type | External (ladder driven) | External | External | External | External | External |
| Automotive Grade | No (commercial) | No | Yes (AEC-Q100) | No | No | No |
Principaux différenciateurs
- Highest sample rate in the NXP ADC1005/1004/1003 video-ADC family (vs ADC1003S050TS/C1)
- External reference ladder enables per-design full-scale optimization (vs ADC0804S040TS/C1 (fixed internal reference))
- Commercial screening with -40 C to +85 C operating range covers industrial use (vs ADC1005S060TS-C18 (automotive grade))
Notes de conception
The ADC1005S060TS/C1:1 has separate analog (AVDD) and digital (DVDD) 5 V supply pins. Decouple each pin with a 100 nF ceramic capacitor placed as close as possible to the IC body, and add a 10 uF bulk tantalum or ceramic capacitor on each rail near the device. Use a ferrite bead or pi-filter between the analog and digital 5 V rails to prevent digital switching noise from coupling into the analog input. Estimated: the typical AVDD current for this ADC family is around 30-40 mA at 60 MSPS, so the ferrite must handle at least 50 mA DC without saturation.
Route the parallel digital output bus (D0-D9) on the opposite side of the PCB from the analog input (AIN) trace to minimize digital-to-analog crosstalk. Place a solid ground plane on layer 2 directly beneath the ADC, and stitch the analog and digital grounds together at a single point near the AGND pin of the IC. Keep the CLK trace short and guarded by ground to limit radiated EMI that can degrade SNR.
The reference ladder requires an external low-noise reference source driven into REFT/REFB. A noisy or unstable reference directly degrades SNR and effective number of bits (ENOB); use a dedicated low-noise reference (such as the ADR01 or REF195) with proper output decoupling. Driving the analog input beyond the reference ladder range causes saturation and harmonic distortion; ensure the input amplifier output common-mode and swing stay within the AVDD/2 +/- REFT window.
Informations de conformité
Compliance fields not directly stated in the verified distributor data. For automotive-grade requirements, the ADC1005S060TS-C18 variant provides AEC-Q100 qualification. RoHS/REACH status should be confirmed with the manufacturer's product compliance documentation.