ADF4002BCPZ-RL7 - 400 MHz Phase Detector PLL | Analog Devices
Référence : ADF4002BCPZ-RL7 ✓ ActifADF4002BCPZ-RL7 Présentation
A phase-locked loop, or PLL, is a feedback-control circuit that locks an output oscillator to a stable reference frequency. Within the broader clock and timing hierarchy, the ADF4002 combines phase detector, frequency divider, charge pump, and synthesizer functions in one clock-and-timing IC. Its programmable dividers allow a relatively low-frequency reference to be multiplied to a desired local-oscillator output while the phase-frequency detector and charge pump correct loop phase and frequency error.
The principal feature of the ADF4002 is its 400 MHz phase-detector operating rate, which supports high-speed frequency-synthesis architectures. A programmable 14-bit R counter accommodates selectable reference-divider ratios, while the N divider sets the integer multiplication relationship between the reference and synthesized output. The low-noise digital phase-frequency detector and precision charge pump support loops intended for RF signal-chain applications where phase noise and reference spur behavior are important.
Technical operation begins with the reference signal entering the programmable reference divider. The divided reference and divided feedback signal are compared by the phase-frequency detector. Their phase difference controls the charge pump, which drives the external loop filter and voltage-controlled oscillator. The resulting divided output is returned through the N divider, closing the feedback loop. Designers therefore need to select loop bandwidth, charge-pump current, filter components, and VCO characteristics according to the required phase noise and lock-time targets.
Typical uses include wireless receiver local oscillators, transmitter up-conversion and down-conversion chains, RF transceiver synthesizers, instrumentation, and communication systems. The device is particularly relevant when a programmable phase detector is needed in a fractional-N or integer-N architecture without integrating the complete RF oscillator into the IC.
The exposed pad requires careful PCB thermal design and grounding. Follow the manufacturer land pattern and reference layout, connect the exposed pad to the appropriate ground plane, and place decoupling and charge-pump components according to the datasheet guidance. Confirm loop stability and phase-noise performance with the actual VCO and filter rather than relying only on calculated divider ratios.
This page organizes the verified electrical identity, package information, sourcing guidance, replacement constraints, and application-oriented engineering guidance. It also distinguishes true pin-compatible alternatives from package or reel-code variants that should not be treated as distinct drop-in designs.
Alternatives de remplacement direct pour ADF4002BCPZ-RL7 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Aucune alternative de remplacement direct disponible pour ce produit.
Demander des alternativesADF4002BCPZ-RL7 Spécifications
| Device Type | Phase detector and PLL frequency synthesizer |
| Maximum Phase Detector Frequency | 400 MHz |
| Maximum Reference Input Frequency | 4 GHz |
| Reference Counter Resolution | 14 bit |
| Reference Divider | Programmable |
| N Divider | Programmable |
| Phase-Frequency Detector | Low-noise digital type |
| Charge Pump | Precision type |
| Minimum Operating Temperature | -40 °C |
| Maximum Operating Temperature | +85 °C |
| Boîtier | 20-lead WFQFN exposed-pad CSP |
| Package Pin Count | 20 pins |
| Type de montage | Surface mount |
| Statut RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Guide de configuration des broches du ADF4002BCPZ-RL7 20 pins
Configuration des broches du ADF4002BCPZ-RL7 (boîtier 20 pins). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour ADF4002BCPZ-RL7.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ADF4002BCPZ-RL7 convient pour 6 applications: Wireless Receiver Local Oscillator, RF Transmitter Up-Conversion, RF Down-Conversion Mixer, Programmable Test Instrumentation, Communications RF Frequency Synthesizer, Low-Phase-Noise RF Signal Source.
Wireless Receiver Local Oscillator
The ADF4002BCPZ-RL7 fits a wireless receiver local-oscillator block because its programmable reference divider, N divider, and 400 MHz phase-detector rate support a flexible synthesis relationship around an external VCO. The designer supplies the charge-pump loop filter and VCO, while the ADF4002 detects phase and frequency error and adjusts the tuning path. This partition is useful when the receiver requires programmable channels, low divider overhead, or a phase-detector capable of operating at high comparison rates. Loop bandwidth and component selection must still deliver the required lock time, phase noise, reference spurs, and channel-settling behavior.
Recommandé
RF Transmitter Up-Conversion
The ADF4002BCPZ-RL7 can generate the programmable local-oscillator signal used by an RF transmitter up-conversion stage. Its programmable reference and feedback dividers allow a stable reference to be multiplied into the LO range required by the mixer, while the precision charge pump provides the control signal for the external VCO tuning input. The 400 MHz phase-detector rate is valuable when the architecture demands a high comparison frequency and low in-band phase noise. Component-level evaluation remains necessary because LO amplitude, tuning range, spur levels, and loop stability depend on the surrounding VCO and filter network.
Recommandé
RF Down-Conversion Mixer
The ADF4002BCPZ-RL7 is appropriate for the local-oscillator path feeding a down-conversion mixer in a receiver or transceiver. The programmable divider system and 14-bit reference counter allow the synthesizer frequency to be adjusted from a shared reference, while the low-noise digital phase-frequency detector helps minimize phase error in the feedback loop. The IC does not directly produce the RF output; it controls an external VCO through the charge pump and loop filter. For production use, characterize tuning sensitivity, integer-N or fractional-N behavior as applicable, lock acquisition, and reference-spur rejection in the complete signal chain.
Recommandé
Programmable Test Instrumentation
The ADF4002BCPZ-RL7 can support programmable clock or local-oscillator generation in test and measurement equipment where the target frequency must be derived from a stable reference and adjusted over a wide range. Its programmable reference divider and N divider provide the multiplication relationship needed around an external VCO, while the 400 MHz phase detector supports high-rate comparison architectures. Instrument designers should optimize the loop for settling time, phase noise, and spurious-signal limits, then include calibration and direct frequency measurements across temperature. The exposed-pad layout and component placement also matter in compact instrument signal-chain layouts.
Recommandé
Communications RF Frequency Synthesizer
The ADF4002BCPZ-RL7 is suited to communications equipment requiring a programmable RF synthesizer built around an external voltage-controlled oscillator. Its precision charge pump and low-noise digital phase-frequency detector form the central error-detection elements, while the 14-bit reference counter and programmable dividers set the frequency relationship. This arrangement supports channel selection in transmitters, receivers, and repeaters where a common reference is distributed across multiple radio functions. Actual suitability depends on VCO tuning range, loop-filter design, temperature drift, startup behavior, and phase-noise targets. The manufacturer evaluation platform can simplify initial register programming and loop verification.
Recommandé
Low-Phase-Noise RF Signal Source
The ADF4002BCPZ-RL7 can form the central phase-detection and divider section of a low-phase-noise RF signal source. Its low-noise digital phase-frequency detector, precision charge pump, and programmable division path provide the control elements needed to lock a low-noise VCO to a reference. The resulting phase-noise performance will depend on the VCO, charge-pump current, loop filter, reference quality, and PCB implementation rather than on the ADF4002 alone. Evaluate integrated phase noise, reference spurs, lock time, and retuning behavior at each required carrier frequency. Use the manufacturer layout and evaluation setup to establish a reproducible baseline before production tuning.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADF4002BCPZ-RL7 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Brand | Analog Devices |
| Package | 20-lead WFQFN exposed-pad CSP |
| Device Type | Phase detector and PLL frequency synthesizer |
| Maximum Phase Detector Frequency | 400 MHz |
| Maximum Reference Input Frequency | 4 GHz |
| Reference Counter Resolution | 14 bit |
| Reference Divider | Programmable |
| N Divider | Programmable |
| Operating Temperature | -40 °C to +85 °C |
Principaux différenciateurs
- High-rate phase detection in an integrated RF synthesizer IC (vs ADF4007BCP)
- Programmable frequency architecture with separate R and N division functions (vs ADF4002SRU-EP)
- Same-family orderable configuration for procurement flexibility (vs ADF4002BCPZ-RL)
Notes de conception
Follow the manufacturer land pattern and reference layout for the 20-lead WFQFN exposed-pad package. Place the charge-pump loop-filter components close to their associated pins, keep the REF and feedback paths compact, and connect the exposed pad to the specified ground-plane structure. Poor high-frequency return paths can degrade phase noise and reference spurs even when the nominal divider settings are correct. Verify the final layout with the manufacturer's evaluation-board stack-up and probing method.
Do not select a similarly named PLL solely by frequency range or package size. Confirm that a proposed substitute has the same 20-pin WFQFN land pattern, reference and feedback pin functions, charge-pump behavior, divider architecture, programming interface, and register map. ADF4002SRU-EP uses a different TSSOP package, while ADF4007BCP is a different PLL family; neither represents a PCB drop-in replacement for the target device.
Decouple the supply pins with the capacitance and placement specified by the ADF4002 Data Sheet, Rev. C. Keep switching return current out of sensitive reference and feedback paths, and connect the exposed pad as directed rather than treating it only as a mechanical feature. The charge-pump and loop-filter network is sensitive to supply disturbance, so compare phase noise and reference spur performance before and after board assembly using a consistent measurement setup.
Characterize lock time, integrated phase noise, reference spurs, and VCO tuning sensitivity across frequency and temperature using the actual external loop. The divider values alone do not establish performance because charge-pump current, loop-filter impedance, VCO gain, and reference phase noise shape the result. Begin with the EVAL-ADF4002 platform, reproduce the target VCO arrangement, and then transfer only validated loop settings and placement rules to the production board.
Informations de conformité
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact orderable part number. The manufacturer product page identifies the ADF4002 as recommended for new designs.