ADS5203IPFBG4 - Dual 10-Bit 40MSPS Low-Power ADC | TI
Référence : ADS5203IPFBG4 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $12.5 | $12,50 |
| 10 | $11.2 | $112,00 |
| 100 | $9.8 | $980,00 |
| 500 | $8.75 | $4 375,00 |
| 1 000 | $7.95 | $7 950,00 |
ADS5203IPFBG4 Présentation
An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog voltage waveforms and produces discrete digital codes proportional to the input amplitude. ADCs sit inside the data-converter sub-class of the broader signal-chain IC family, which also includes DACs, amplifiers, and clock ICs. Within the ADC category, the ADS5203IPFBG4 belongs to the high-speed pipelined sub-type, which uses cascaded low-resolution stages and digital error correction to achieve conversion rates from tens to hundreds of MSPS, making it the dominant architecture for video, communications, and industrial imaging.
The device delivers 300 MHz analog input bandwidth, low power consumption suitable for portable and densely populated boards, and an operating temperature range of -40C to +85C (industrial grade). The dual simultaneous sample-and-hold inputs are critical for I/Q signal processing, medical imaging, and any application that requires phase-coherent acquisition of two channels. The integrated bandgap reference and internal clock simplifier simplify external BOM.
Architecturally, the converter employs TI's proprietary 10-bit pipelined conversion method, where each stage resolves a few bits, drives a residue to the next stage, and applies digital correction. The 3.3 V single-supply operation is decoupled with a 10 uF bulk and 0.1 uF ceramic cap placed within 5 mm of the AVDD pins. The dual parallel bus mode lets the host processor read channel A on one bus and channel B on another, halving effective read latency at the system level.
Typical applications include medical ultrasound front-end signal acquisition, CCD/CIS scanner digitizers, basestation I/Q digitizers, and portable test-and-measurement equipment. The wide analog input bandwidth also suits time-interleaved multi-channel digitizer cards and CCD-based industrial cameras.
When designing with this part, decouple AVDD and DRVDD separately and route analog and digital grounds through a star point at the exposed pad. The pipelined architecture typically exhibits a 2.5-cycle latency between sampling and output, which must be budgeted for in synchronous system timing.
This page synthesizes distributor pricing for ADS5203IPFBG4, drop-in replacement options, and PCB design considerations that are not aggregated in the manufacturer datasheet alone.
Alternatives de remplacement direct pour ADS5203IPFBG4 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADS5203IPFBG4 (même facteur de forme et même empreinte) — différant par Package, Operating Temperature, Input Type, Number of Channels, Output Interface.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ADS5203IPFB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADS5203IPFBRG4
✅ Remplacement direct✓ En stock
$5.73 / unité
Voir la fiche technique →ADS5103IPFBRG4
✅ Remplacement direct✓ En stock
$4.4 / unité
Voir la fiche technique →ADS5103CPFBRG4
✅ Remplacement direct✓ En stock
$4.95 / unité
Voir la fiche technique →ADS5103CPFBR
✅ Remplacement direct✓ En stock
$4.45 / unité
Voir la fiche technique →ADS5102IPFBR
✅ Remplacement direct✓ En stock
$5.05 / unité
Voir la fiche technique →ADS5203IPFBG4 Valeurs maximales et caractéristiques électriques
| Résolution | 10 bits |
| Sample Rate | 40 MSPS per channel |
| Number of Channels | 2 (dual, simultaneous) |
| Architecture | Pipelined |
| Tension d'alimentation | 3.3 V single supply |
| Analog Input Bandwidth | 300 MHz |
| Input Type | Differential or single-ended |
| SNR | 60 dB at fIN = 10.5 MHz |
| SFDR | 73 dB at fIN = 10.5 MHz |
| Output Interface | Single or dual parallel bus |
| Sample-and-Hold | Dual simultaneous |
| Température de fonctionnement | -40C to +85C |
| Boîtier | 48-TQFP (7x7 mm) |
| Type de montage | Surface Mount |
| Temperature Grade | Industrial |
| Terminal Form | Gull wing |
| Number of Terminals | 48 |
| Package Code | TFQFP |
Configuration des broches de ADS5203IPFBG4
| Broche 1 | AVDD — Analog supply voltage (3.3 V) |
| Broche 2 | AINP — Channel A positive analog input |
| Broche 3 | AINN — Channel A negative analog input |
| Broche 4 | AGND — Analog ground |
| Broche 5 | BINP — Channel B positive analog input |
| Broche 6 | BINN — Channel B negative analog input |
| Broche 7 | REFT — Top reference decoupling |
| Broche 8 | REFB — Bottom reference decoupling |
| Broche 9 | VREF — Reference voltage bypass |
| Broche 10 | AGND — Analog ground |
| Broche 11 | CLK — ADC sample clock input |
| Broche 12 | CLKB — Complementary clock input |
| Broche 13 | OE — Output enable (active low) |
| Broche 14 | DRVDD — Digital output supply (3.3 V) |
| Broche 15 | DRGND — Digital ground |
| Broche 16 | D0A — Channel A data bit 0 (LSB) |
| Broche 17 | D1A — Channel A data bit 1 |
| Broche 18 | D2A — Channel A data bit 2 |
| Broche 19 | D3A — Channel A data bit 3 |
| Broche 20 | D4A — Channel A data bit 4 |
| Broche 21 | D5A — Channel A data bit 5 |
| Broche 22 | D6A — Channel A data bit 6 |
| Broche 23 | D7A — Channel A data bit 7 |
| Broche 24 | D8A — Channel A data bit 8 |
| Broche 25 | D9A — Channel A data bit 9 (MSB) |
| Broche 26 | DRGND — Digital ground |
| Broche 27 | DRVDD — Digital output supply (3.3 V) |
| Broche 28 | D0B — Channel B data bit 0 (LSB) |
| Broche 29 | D1B — Channel B data bit 1 |
| Broche 30 | D2B — Channel B data bit 2 |
| Broche 31 | D3B — Channel B data bit 3 |
| Broche 32 | D4B — Channel B data bit 4 |
| Broche 33 | D5B — Channel B data bit 5 |
| Broche 34 | D6B — Channel B data bit 6 |
| Broche 35 | D7B — Channel B data bit 7 |
| Broche 36 | D8B — Channel B data bit 8 |
| Broche 37 | D9B — Channel B data bit 9 (MSB) |
| Broche 38 | DRGND — Digital ground |
| Broche 39 | PD — Power-down mode control |
| Broche 40 | MODE — Output mode select (single/dual bus) |
| Broche 41 | AVDD — Analog supply voltage (3.3 V) |
| Broche 42 | AGND — Analog ground |
| Broche 43 | BIASJ — Bias current setting |
| Broche 44 | CM — Common-mode voltage bypass |
| Broche 45 | REFCAP — Reference decoupling capacitor |
| Broche 46 | RESET — Digital reset input |
| Broche 47 | DRVDD — Digital output supply (3.3 V) |
| Broche 48 | GND — Exposed pad / primary ground |
Applications typiques
ADS5203IPFBG4 convient pour 6 applications: Medical Ultrasound Front-End, CCD/CIS Scanner Digitizer, Basestation I/Q Digitizer, Industrial CCD Camera Imaging, Portable Test and Measurement, Communications IF Sampling.
Medical Ultrasound Front-End
The ADS5203IPFBG4 fits medical ultrasound front-end digitizers where two phase-coherent analog channels per transducer element must be sampled simultaneously. Its dual simultaneous sample-and-hold inputs preserve phase and amplitude alignment between the I and Q receive paths, and the 300 MHz analog input bandwidth handles the wideband echoes from broadband piezoelectric transducers. The 60 dB SNR at fIN = 10.5 MHz supports the dynamic range required for harmonic imaging modes. Place the ADC on a low-noise inner layer with split AVDD/DRVDD planes and decouple each rail with 10 uF bulk plus 0.1 uF ceramic caps within 5 mm of the supply pins.
Recommandé
CCD/CIS Scanner Digitizer
The ADS5203IPFBG4 suits CCD and CIS (contact image sensor) scanner digitizers where color channels must be captured with tight channel-to-channel matching. The dual pipelined ADC lets the designer sample two color stripes per pixel clock, halving the analog front-end component count. The 3.3 V single-supply operation simplifies scanner power architecture, while the differential input mode rejects common-mode noise from the high-speed shift-register clocks. Use the dual parallel bus output mode to feed both channels directly into a single FPGA at half the per-channel latency.
Recommandé
Basestation I/Q Digitizer
The ADS5203IPFBG4 is a strong fit for cellular base-station I/Q digitizers in receiver signal chains, where the I and Q baseband outputs of a quadrature demodulator must be captured with precise amplitude and phase balance. Its 10-bit resolution at 40 MSPS supports GSM/EDGE and early WCDMA receiver paths. The 73 dB SFDR at fIN = 10.5 MHz rejects out-of-band blocker distortion, and the 300 MHz analog input bandwidth enables direct IF sampling at low intermediate frequencies. Use a TCXO or OCXO reference to drive the ADC clock input for low-jitter sampling.
Recommandé
Industrial CCD Camera Imaging
The ADS5203IPFBG4 supports industrial CCD-based machine-vision cameras where two synchronized analog video channels must be digitized at high throughput. The dual simultaneous sample-and-hold maintains pixel-to-pixel registration between adjacent sensor rows, critical for accurate line-scan measurements in factory automation. The 48-TQFP footprint integrates cleanly onto compact camera PCBs alongside the sensor, FPGA, and DRAM. The industrial -40C to +85C temperature grade supports factory floor deployments, and the low power dissipation simplifies sealed-enclosure thermal design.
Recommandé
Portable Test and Measurement
The ADS5203IPFBG4 is well suited to portable two-channel oscilloscope and data-acquisition front-ends where dual simultaneous digitizing channels are required in a battery-powered form factor. The 3.3 V single-supply operation runs directly from Li-ion chemistry without complex regulator cascades. The 40 MSPS per channel rate handles audio-bandwidth and IF-bandwidth signal capture, and the differential input mode rejects ground bounce in mixed analog-digital portable enclosures. Low power dissipation extends battery runtime, and the 48-TQFP compact footprint preserves PCB real estate for the display, battery, and user interface.
Recommandé
Communications IF Sampling
The ADS5203IPFBG4 fits communications IF-sampling receiver cards where analog signals at intermediate frequencies must be digitized directly without an analog downconversion stage. The 300 MHz input bandwidth supports undersampling of IF signals in the 70-150 MHz range, while the 73 dB SFDR keeps spur performance acceptable for narrowband channel extraction. Use a low-jitter clock oscillator to drive the ADC clock input, and decouple AVDD and DRVDD with separate ferrite beads to prevent digital switching noise from coupling into the analog input. The dual parallel bus mode allows the FPGA to process two IF channels independently in real time.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADS5203IPFBG4 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADS5203IPFB | ADS5203IPFBRG4 | ADS5103IPFBRG4 | ADS5103CPFBRG4 | ADS5102IPFBR |
|---|---|---|---|---|---|---|
| Package | 48-TQFP (7x7) | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 10 bits | 10 bits | 10 bits | 10 bits | 10 bits | 10 bits |
| Channels | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) |
| Supply Voltage | 3.3 V single | 3.3 V single | 3.3 V single | 3.3 V single | 3.3 V single | 3.3 V single |
| Temperature Grade | Industrial -40C to +85C | Industrial | Industrial | Industrial | Industrial | Industrial |
| Packaging Code | G4 (tube, lead-free) | non-G4 | RG4 (tape and reel) | RG4 (tape and reel) | RG4 (tape and reel) | non-G4 |
Principaux différenciateurs
- Dual simultaneous sample-and-hold at 40 MSPS per channel (vs ADS5203IPFB)
- 48-TQFP pin-compatible across the ADS5203 / ADS5103 family (vs ADS5103IPFBRG4)
- 300 MHz analog input bandwidth supports undersampling (vs ADS5102IPFBR)
Notes de conception
Decouple AVDD and DRVDD with separate ferrite beads or filter sections to prevent digital switching noise from coupling into the analog supply. Place a 10 uF bulk capacitor and a 0.1 uF ceramic bypass within 5 mm of each supply pin. The analog supply (AVDD) is the most noise-sensitive node and must use a low-noise LDO, not a switching regulator, for optimal SNR and SFDR performance.
Use a four-layer PCB with separate analog and digital ground planes joined at a single star point beneath the exposed pad (pin 48). Route analog input traces as differential pairs with controlled 100 ohm differential impedance, and keep them away from digital output bus traces to avoid coupling clock-related spurs into the analog front end. The exposed pad must be soldered to the analog ground plane for thermal dissipation and electrical reference.
Drive the CLK input with a low-jitter clock source (TCXO or OCXO); the SNR performance of the ADS5203IPFBG4 degrades proportionally to clock jitter, especially at high input frequencies. Keep the CLK trace short and impedance-controlled, and use complementary CLKB if available. For best SFDR, match the common-mode voltage of the analog input drive to the ADC internal common-mode reference (CM pin).
Do not exceed the absolute maximum analog input voltage; the differential input range is centered around the internal common-mode voltage. Always enable the internal reference (VREF) with the recommended bypass capacitor on REFCAP - omitting this degrades SNR and SFDR. The pipelined architecture introduces a fixed 2.5-clock-cycle latency between sampling and output, which must be budgeted in synchronous systems.
Informations de conformité
Lead-free per G4 finish suffix; RoHS compliant per TI product page. Not AEC-Q100 qualified - this is an industrial/consumer ADC, not an automotive grade part.
