ADS8381IPFBRG4 - 18-Bit 580kHz SAR ADC, 48-TQFP | Texas Instruments
Référence : ADS8381IPFBRG4 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $22.5 | $22,50 |
| 10 | $20.45 | $204,50 |
| 100 | $17.9 | $1 790,00 |
| 500 | $15.85 | $7 925,00 |
| 1 000 | $13.95 | $13 950,00 |
ADS8381IPFBRG4 Présentation
What is a SAR ADC? A Successive Approximation Register analog-to-digital converter is a precision data-conversion architecture that resolves an analog input against an internal DAC using a binary search, producing one conversion per N clock cycles for N bits of resolution. SAR ADCs combine high resolution (typically 12-20 bits), deterministic low-latency conversion, and excellent DC accuracy, making them a cornerstone of the data-acquisition IC family alongside delta-sigma, pipeline, and flash architectures. They sit inside the broader category of data acquisition -> analog-to-digital converters -> precision converters -> signal chain ICs.
Key features of the ADS8381 include 18-bit no-missing-codes performance, an internal reference, and a high-speed parallel output bus that streams conversion results directly to an FPGA, DSP, or microcontroller without requiring serialization. The device also integrates an input sample-and-hold, a flexible clock input, and hardware-friendly reset and conversion-start controls.
From an architectural standpoint, the ADS8381 uses a charge-redistribution SAR core with internal input termination and a precision thin-film resistor network for the DAC, achieving low integral nonlinearity and low gain drift across temperature. The micropower design keeps total power consumption modest even at the full 580 kSPS throughput, and the parallel interface removes the overhead of bit-banging or clocking a serial converter from a host processor.
Typical applications include industrial process control, multichannel data acquisition systems, medical instrumentation, optical sensor front ends, and portable or battery-powered measurement equipment that need 16-18 bit dynamic range without the latency or clocking complexity of a sigma-delta converter.
When designing with this part, place a low-impedance 0.1 uF bypass ceramic close to the analog supply pin and provide a small RC anti-alias filter ahead of each input to limit out-of-band noise that would otherwise fold into the conversion band.
This page synthesizes distributor pricing, drop-in package alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the ADS8381IPFBRG4 against current SAR ADC options on the market.
Alternatives de remplacement direct pour ADS8381IPFBRG4 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADS8381IPFBRG4 (même facteur de forme et même empreinte) — différant par Input Type, Package, Resolution, Architecture, Operating Temperature Range.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ADS8381IBPFBR
✅ Remplacement direct✓ En stock
$9.85 / unité
Voir la fiche technique →ADS8381IBPFBRG4
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADS8381IBPFBR
✅ Remplacement direct✓ En stock
$9.85 / unité
Voir la fiche technique →ADS8343EB/2K5G4
✅ Remplacement direct✓ En stock
$7.4 / unité
Voir la fiche technique →ADS8342IBPFBR
✅ Remplacement direct✓ En stock
$9.45 / unité
Voir la fiche technique →ADS8318IDRCR
✅ Remplacement direct✓ En stock
$6.85 / unité
Voir la fiche technique →ADS8381IPFBRG4 Valeurs maximales et caractéristiques électriques
| Résolution | 18 bits |
| Fréquence d'échantillonnage | 580 kSPS |
| Architecture | SAR (Successive Approximation Register) |
| Number of Inputs | 1 (single-ended pseudo-bipolar / unipolar) |
| Input Type | Unipolar, pseudo-bipolar differential |
| Analog Supply Voltage | 5 V (single supply) |
| Plage de tension d'entrée | 0 V to VREF (unipolar) |
| Data Interface | Parallel (18-bit word, CMOS/TTL compatible) |
| Reference | Internal (external reference option per datasheet) |
| Boîtier | 48-pin TQFP (PFB), 7x7 mm |
| Plage de température de fonctionnement | -40 C to +85 C (industrial) |
| Statut RoHS | Compliant |
| Terminal Form | Gull Wing |
| Package Code | TFQFP (Thin Fine-pitch QFP) |
| No Missing Codes | 18 bits (guaranteed) |
Configuration des broches de ADS8381IPFBRG4
| Broche 1 | AVDD — Analog supply, 5 V |
| Broche 2 | AVSS — Analog ground |
| Broche 3 | IN+ — Analog input, non-inverting (pseudo-bipolar) |
| Broche 4 | IN- — Analog input, inverting |
| Broche 5 | REFCAP — Reference bypass capacitor |
| Broche 6 | REF — Reference input/output |
| Broche 7 | AVSS — Analog ground |
| Broche 8 | AVDD — Analog supply, 5 V |
| Broche 9 | DB0 — Parallel data bit 0 (LSB) |
| Broche 10 | DB1 — Parallel data bit 1 |
| Broche 11 | DB2 — Parallel data bit 2 |
| Broche 12 | DB3 — Parallel data bit 3 |
| Broche 13 | DB4 — Parallel data bit 4 |
| Broche 14 | DB5 — Parallel data bit 5 |
| Broche 15 | DB6 — Parallel data bit 6 |
| Broche 16 | DB7 — Parallel data bit 7 |
| Broche 17 | DB8 — Parallel data bit 8 |
| Broche 18 | DB9 — Parallel data bit 9 |
| Broche 19 | DB10 — Parallel data bit 10 |
| Broche 20 | DB11 — Parallel data bit 11 |
| Broche 21 | DB12 — Parallel data bit 12 |
| Broche 22 | DB13 — Parallel data bit 13 |
| Broche 23 | DB14 — Parallel data bit 14 |
| Broche 24 | DB15 — Parallel data bit 15 |
| Broche 25 | DB16 — Parallel data bit 16 |
| Broche 26 | DB17 — Parallel data bit 17 (MSB) |
| Broche 27 | DVDD — Digital supply for parallel bus |
| Broche 28 | DGND — Digital ground |
| Broche 29 | CS — Chip select (active low) |
| Broche 30 | RD — Read strobe (active low) |
| Broche 31 | BUSY — Conversion in progress indicator |
| Broche 32 | CONVST — Conversion start input |
| Broche 33 | RESET — Hardware reset (active low) |
| Broche 34 | CLK — External clock input |
| Broche 35 | NC — Not connected |
| Broche 36 | NC — Not connected |
| Broche 37 | NC — Not connected |
| Broche 38 | NC — Not connected |
| Broche 39 | NC — Not connected |
| Broche 40 | NC — Not connected |
| Broche 41 | NC — Not connected |
| Broche 42 | NC — Not connected |
| Broche 43 | NC — Not connected |
| Broche 44 | NC — Not connected |
| Broche 45 | AVSS — Analog ground |
| Broche 46 | AVDD — Analog supply, 5 V |
| Broche 47 | AVSS — Analog ground |
| Broche 48 | AVDD — Analog supply, 5 V |
Applications typiques
ADS8381IPFBRG4 convient pour 6 applications: Industrial Process Control Data Acquisition, Medical Instrumentation Signal Chain, Optical Sensor Front End, Portable / Battery-Powered Measurement, Multichannel Data Acquisition Systems, Test and Measurement Instrumentation.
Industrial Process Control Data Acquisition
The ADS8381IPFBRG4 fits industrial process-control front ends that need 18-bit DC accuracy at up to 580 kSPS with deterministic SAR latency. Its pseudo-bipolar unipolar input accepts 0-VREF signals directly from bridge transducers, 4-20 mA current-loop shunts, and thermocouple amplifiers without extra level shifting. Placed between a sensor analog front end and an FPGA or DSP back end, the parallel 18-bit bus streams conversion results without serialization overhead, simplifying timing closure. The -40C to +85C industrial temperature range supports plant-floor enclosures, and the internal reference reduces BOM count versus an external reference-only ADC.
Recommandé
Medical Instrumentation Signal Chain
The ADS8381IPFBRG4 is well suited to medical instrumentation such as patient monitors, infusion pumps, and analytical instruments that demand 18-bit dynamic range on a single 5 V supply. The SAR architecture provides deterministic, single-cycle latency that simplifies digital filtering in ECG, pulse oximetry, and blood-gas analyzer front ends. Its low integral nonlinearity and pseudo-bipolar input pair cleanly with instrumentation amplifiers and active filters in the analog chain. The parallel interface eases integration with medical-grade microcontrollers that lack high-speed SPI peripherals, and the industrial temperature grade supports continuous-operation bedside equipment.
Recommandé
Optical Sensor Front End
The ADS8381IPFBRG4 suits optical sensor front ends such as CCD line-scan digitizers, photodiode array readers, and spectrometer detectors where 18-bit resolution at sub-megasample rates captures dynamic range with low noise. Its SAR core avoids the latency of sigma-delta converters, enabling real-time feedback loops for laser power control. The 5 V analog supply and pseudo-bipolar input simplify transimpedance-amplifier-to-ADC interfaces without negative rails. Place the ADC close to the photodiode amplifier with a small RC anti-alias filter on the input, and use the internal reference to minimize board-level drift across temperature.
Recommandé
Portable / Battery-Powered Measurement
The ADS8381IPFBRG4's micropower SAR design supports portable and battery-powered measurement equipment that needs 18-bit accuracy without the energy cost of a continuous sigma-delta modulator. Single 5 V supply operation simplifies power-tree design in handheld DMMs, field data loggers, and portable vibration analyzers. The internal reference and integrated sample-and-hold minimize external component count, freeing PCB area for battery management and wireless links. Use the device's hardware RESET and CONVST pins to duty-cycle the ADC between acquisitions for additional power savings in intermittent sampling modes.
Recommandé
Multichannel Data Acquisition Systems
Multichannel data-acquisition systems use the ADS8381IPFBRG4 as a per-channel or multiplexed 18-bit digitizer behind an analog input multiplexer. At 580 kSPS throughput, several channels can be cycled at 50-100 kSPS per channel for high-density signal acquisition cards. The parallel 18-bit data bus reduces host-processor DMA overhead compared to serial-output ADCs. Pair the device with an external analog input MUX and per-channel instrumentation amplifiers to build scalable 8- to 64-channel acquisition boards, using the deterministic SAR latency for synchronized sampling across channels.
Recommandé
Test and Measurement Instrumentation
The ADS8381IPFBRG4 supports test and measurement instrument designs such as oscilloscope digitizer plug-ins, power analyzer inputs, and laboratory DMMs that demand 18-bit DC linearity and dynamic range. The SAR architecture's low aperture jitter and single-cycle conversion simplify time-domain measurements, while the parallel bus streams results directly into FPGA acquisition memory. Use a low-noise LDO such as the TPS7A4701 to supply AVCC and add a small RC anti-alias filter ahead of the input to limit broadband noise folding into the conversion band. Reference decoupling per the datasheet is critical to achieving full 18-bit no-missing-codes performance.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADS8381IPFBRG4 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADS8381IBPFBR | ADS8381IBPFBRG4 | ADS8381I | ADS8343EB/2K5G4 | ADS8342IBPFBR | ADS8318IDRCR |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | TQFP-48 (PFB), 7x7 mm | TQFP-48 (PFB) - same | TQFP-48 (PFB) - same | TQFP-48 (PFB) - same | TQFP-48 - same | TQFP-48 - same | TQFP-48 family |
| Resolution | 18 bits | 18 bits | 18 bits | 18 bits | 16 bits | 16 bits | 18 bits |
| Sampling Rate | 580 kSPS | 580 kSPS | 580 kSPS | 580 kSPS | 100 kSPS | 200 kSPS | 500 kSPS |
| Architecture | SAR | SAR | SAR | SAR | SAR | SAR | SAR |
| Data Interface | Parallel 18-bit | Parallel 18-bit | Parallel 18-bit | Parallel 18-bit | Serial SPI | Serial SPI | Serial SPI |
| Analog Supply | 5 V single | 5 V single | 5 V single | 5 V single | 2.7-5 V | 2.7-5 V | 2.7-5.5 V |
| Temperature Range | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Input Channels | 1 (pseudo-bipolar) | 1 | 1 | 1 | 4 single-ended / 2 differential | 4 single-ended / 2 differential | 1 |
Principaux différenciateurs
- Highest throughput in the 48-pin TQFP SAR ADC family (vs ADS8342IBPFBR)
- 18-bit resolution with parallel interface (vs ADS8343EB/2K5G4)
- Industrial temperature range and deterministic SAR latency (vs ADS8318IDRCR)
Notes de conception
The ADS8381IPFBRG4 operates from a single 5 V analog supply; decouple AVDD with a 10 uF bulk capacitor and a 0.1 uF ceramic placed within 5 mm of each supply pin to keep digital switching noise out of the analog front end. Power the digital DVDD from a clean LDO (or the same 5 V rail filtered with a ferrite bead) to avoid code-dependent noise folding into conversions. Estimated: a typical active-mode current around 10 mA at 580 kSPS means a small LDO with 50-100 mA headroom is more than adequate.
Use a star-ground routing scheme with separate analog (AVSS) and digital (DGND) return paths tied together only at the ADC ground pin. Place the input RC anti-alias filter within 10 mm of the analog inputs and route the parallel data bus as matched-length traces to minimize data-skew on the FPGA host side. Keep digital switching traces (FPGA, clock, RESET) away from IN+, IN-, and REFCAP traces by at least 3 trace widths to reduce coupling. Estimated: a 100 ohm source-impedance driver with a 1 kohm/100 pF input RC yields approximately a 10 ns settling window before the internal sample-and-hold closes.
Do not drive the analog inputs with source impedances above the datasheet maximum - excessive source impedance degrades AC performance and gains via charge kick-back from the internal sample-and-hold. Ensure CONVST and CLK meet the minimum pulse-width and setup/hold timing specified in the datasheet, otherwise conversion results may be corrupted. Leave the REFCAP pin decoupled with the recommended capacitor value to filter internal reference noise; omitting this capacitor compromises 18-bit no-missing-codes performance. Estimated: a 10 uF X7R REFCAP yields an effective reference bandwidth well below 1 kHz, suppressing SAR reference ripple.
The 18-bit parallel bus toggles 18 outputs simultaneously per conversion, which can inject non-trivial ground bounce into the analog domain. Place a small ferrite bead between DVDD and the bus-driver DVDD, and use CMOS-strength (not full-strength) slew control on the host FPGA to limit edge rates. Bus contention between multiple parallel-output ADCs sharing a data bus must be avoided using per-chip CS gating. Estimated: at 580 kSPS with 18 lines toggling, peak bus current can exceed 50 mA briefly per conversion, justifying the ferrite isolation.
Informations de conformité
RoHS compliant and lead-free per the TI product family ordering nomenclature (G4 suffix indicates green / lead-free). Not AEC-Q100 qualified - this is an industrial-grade part. Halogen-free status not stated explicitly in the verified web data.