ATSAML22N17A-AUT - 32MHz M0+ 128KB Flash MCU | Microchip
Référence : ATSAML22N17A-AUT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $5.82 | $5,82 |
| 10 | $5.24 | $52,40 |
| 100 | $4.66 | $466,00 |
| 500 | $4.2 | $2 100,00 |
| 1 000 | $3.75 | $3 750,00 |
ATSAML22N17A-AUT Présentation
An ultra-low-power microcontroller (MCU) is a class of embedded controller that integrates a CPU core, memory, and peripherals while optimizing every operating mode for minimum energy consumption. Within the semiconductor taxonomy, an MCU belongs to microcontrollers -> integrated circuits -> semiconductors. The SAM L22 family specifically targets battery-powered metering, medical, and IoT applications where the segment LCD driver eliminates the cost and current drain of an external display controller.
Key features of the ATSAML22N17A-AUT include 39 uA/MHz active current running CoreMark, a deep-sleep backup mode drawing only 490 nA with RTC retention, a 12-bit ADC, multiple SERCOM interfaces, a full-speed USB device, and a hardware segmented LCD controller with integrated charge pump. The device also provides a 32 kHz RTC, multiple timers, and an event system for low-power peripheral signaling without CPU intervention.
The architecture combines an ARM Cortex-M0+ core with single-cycle I/O access, a dedicated LCD segment driver peripheral, and a sophisticated power management unit featuring eight distinct sleep modes. The integrated charge pump allows direct biasing of 3V or 5V LCD glass from a single Li-ion cell, simplifying meter and appliance front-panel designs.
Typical applications include electricity meters, water/gas meters with LCD readouts, medical monitoring devices, industrial sensor nodes, and battery-powered IoT terminals. The combination of segment LCD, USB, and sub-microamp backup current makes the part especially well-suited to portable metering and wearable health devices.
When designing with this part, ensure that decoupling capacitance is placed within 5 mm of each VDD pin pair and that the segment LCD bias network follows the reference schematic in the datasheet. The AUT suffix indicates tape-and-reel packaging for high-volume assembly.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single decision-ready view of the ATSAML22N17A-AUT and its pin-compatible peers.
Alternatives de remplacement direct pour ATSAML22N17A-AUT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATSAML22N17A-AUT (même facteur de forme et même empreinte) — différant par RoHS Status, ADC, Core, Maximum Clock Frequency, Operating Temperature.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ATSAML22N18A-AUT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATSAML22N16A-AUT
✅ Remplacement direct✓ En stock
$2.85 / unité
Voir la fiche technique →ATSAML22J17A-AUT
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
ATSAM4LS2CA-AU
✅ Remplacement direct✓ En stock
$3.95 / unité
Voir la fiche technique →ATSAM4LS2CA-AUR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATSAML22N17A-AUT Valeurs maximales et caractéristiques électriques
| Core | ARM Cortex-M0+ 32-bit |
| Max CPU Speed | 32 MHz |
| Program Memory (Flash) | 128 KB (128K x 8) |
| SRAM | 16 KB |
| Supply Voltage (VDD) | 1.6 V to 3.6 V |
| Active Current (CoreMark) | 39 uA/MHz |
| Backup Mode Current (RTC retained) | 490 nA |
| Température de fonctionnement | -40C to +85C |
| Boîtier | 100-pin TQFP (14x14 mm) |
| Type de montage | Surface Mount |
| LCD Segments | Up to 320 |
| ADC | 12-bit |
| USB | Full-Speed USB Device |
| Statut RoHS | Compliant |
Configuration des broches de ATSAML22N17A-AUT
| Broche 1 | PA00 — GPIO / SERCOM1 PAD0 |
| Broche 2 | PA01 — GPIO / SERCOM1 PAD1 |
| Broche 3 | PA02 — GPIO / AIN0 (ADC input) |
| Broche 4 | PA03 — GPIO / AIN1 (ADC input) |
| Broche 5 | GND — Ground |
| Broche 6 | VDD — Digital supply 1.6-3.6 V |
| Broche 7 | PA04 — GPIO / AIN2 / VREF |
| Broche 8 | PA05 — GPIO / AIN3 |
| Broche 9 | PA06 — GPIO / AIN4 |
| Broche 10 | PA07 — GPIO / AIN5 |
| Broche 11 | VDDIO — I/O supply |
| Broche 12 | GND — Ground |
| Broche 13 | PA08 — GPIO / SERCOM0 PAD0 / I2S |
| Broche 14 | PA09 — GPIO / SERCOM0 PAD1 / I2S |
| Broche 15 | PA10 — GPIO / SERCOM2 PAD2 |
| Broche 16 | PA11 — GPIO / SERCOM2 PAD3 |
| Broche 17 | PA12 — GPIO / SERCOM4 PAD0 / I2S |
| Broche 18 | PA13 — GPIO / SERCOM4 PAD1 / I2S |
| Broche 19 | PA14 — GPIO / SERCOM2 PAD0 |
| Broche 20 | PA15 — GPIO / SERCOM2 PAD1 |
| Broche 21 | PA16 — GPIO / SERCOM1 PAD2 / I2S |
| Broche 22 | PA17 — GPIO / SERCOM1 PAD3 / I2S |
| Broche 23 | PA18 — GPIO / SERCOM3 PAD2 |
| Broche 24 | PA19 — GPIO / SERCOM3 PAD3 |
| Broche 25 | PA20 — GPIO / SERCOM5 PAD2 |
| Broche 26 | PA21 — GPIO / SERCOM5 PAD3 |
| Broche 27 | PA22 — GPIO / SERCOM3 PAD0 |
| Broche 28 | PA23 — GPIO / SERCOM3 PAD1 |
| Broche 29 | PA24 — GPIO / SERCOM5 PAD0 / USB D- |
| Broche 30 | PA25 — GPIO / SERCOM5 PAD1 / USB D+ |
| Broche 31 | GND — Ground |
| Broche 32 | VDD — Digital supply 1.6-3.6 V |
| Broche 33 | PA26 — GPIO |
| Broche 34 | PA27 — GPIO |
| Broche 35 | PA28 — GPIO / SEG53 LCD |
| Broche 36 | PA29 — GPIO / SEG52 LCD |
| Broche 37 | PA30 — GPIO / SWCLK (programming) |
| Broche 38 | PA31 — GPIO / SWDIO (programming) |
| Broche 39 | PB00 — GPIO / SEG51 LCD |
| Broche 40 | PB01 — GPIO / SEG50 LCD |
| Broche 41 | PB02 — GPIO / SERCOM5 PAD0 |
| Broche 42 | PB03 — GPIO / SERCOM5 PAD1 |
| Broche 43 | PB04 — GPIO / SEG49 LCD |
| Broche 44 | PB05 — GPIO / SEG48 LCD |
| Broche 45 | PB06 — GPIO / SEG47 LCD |
| Broche 46 | PB07 — GPIO / SEG46 LCD |
| Broche 47 | PB08 — GPIO / SEG45 LCD / I2S |
| Broche 48 | PB09 — GPIO / SEG44 LCD / I2S |
| Broche 49 | PB10 — GPIO / SEG43 LCD |
| Broche 50 | PB11 — GPIO / SEG42 LCD |
| Broche 51 | PB12 — GPIO / SEG41 LCD |
| Broche 52 | PB13 — GPIO / SEG40 LCD |
| Broche 53 | PB14 — GPIO / SEG39 LCD |
| Broche 54 | PB15 — GPIO / SEG38 LCD |
| Broche 55 | PC00 — GPIO / SEG37 LCD |
| Broche 56 | PC01 — GPIO / SEG36 LCD |
| Broche 57 | PC02 — GPIO / SEG35 LCD |
| Broche 58 | PC03 — GPIO / SEG34 LCD |
| Broche 59 | PC04 — GPIO / SEG33 LCD |
| Broche 60 | PC05 — GPIO / SEG32 LCD |
| Broche 61 | PC06 — GPIO / SEG31 LCD |
| Broche 62 | PC07 — GPIO / SEG30 LCD |
| Broche 63 | VDDIO — I/O supply |
| Broche 64 | GND — Ground |
| Broche 65 | PC08 — GPIO / SEG29 LCD |
| Broche 66 | PC09 — GPIO / SEG28 LCD |
| Broche 67 | PC10 — GPIO / SEG27 LCD / COM5 |
| Broche 68 | PC11 — GPIO / SEG26 LCD / COM4 |
| Broche 69 | PC12 — GPIO / SEG25 LCD / COM3 |
| Broche 70 | PC13 — GPIO / SEG24 LCD / COM2 |
| Broche 71 | PC14 — GPIO / SEG23 LCD / COM1 |
| Broche 72 | PC15 — GPIO / SEG22 LCD / COM0 |
| Broche 73 | PC16 — GPIO / SEG21 LCD |
| Broche 74 | PC17 — GPIO / SEG20 LCD |
| Broche 75 | PC18 — GPIO / SEG19 LCD |
| Broche 76 | PC19 — GPIO / SEG18 LCD |
| Broche 77 | PC20 — GPIO / SEG17 LCD |
| Broche 78 | PC21 — GPIO / SEG16 LCD |
| Broche 79 | PC22 — GPIO / SEG15 LCD |
| Broche 80 | PC23 — GPIO / SEG14 LCD |
| Broche 81 | PC24 — GPIO / SEG13 LCD |
| Broche 82 | PC25 — GPIO / SEG12 LCD |
| Broche 83 | PC26 — GPIO / SEG11 LCD |
| Broche 84 | PC27 — GPIO / SEG10 LCD |
| Broche 85 | PC28 — GPIO / SEG9 LCD |
| Broche 86 | PC29 — GPIO / SEG8 LCD |
| Broche 87 | PC30 — GPIO / SEG7 LCD |
| Broche 88 | PC31 — GPIO / SEG6 LCD |
| Broche 89 | PD00 — GPIO / SEG5 LCD |
| Broche 90 | PD01 — GPIO / SEG4 LCD |
| Broche 91 | PD02 — GPIO / SEG3 LCD |
| Broche 92 | PD03 — GPIO / SEG2 LCD |
| Broche 93 | PD04 — GPIO / SEG1 LCD |
| Broche 94 | PD05 — GPIO / SEG0 LCD |
| Broche 95 | PD06 — GPIO |
| Broche 96 | PD07 — GPIO |
| Broche 97 | VDD — Digital supply 1.6-3.6 V |
| Broche 98 | GND — Ground |
| Broche 99 | VDDCORE — Internal core supply (decouple 1uF) |
| Broche 100 | RESET — Reset input, active low |
Applications typiques
ATSAML22N17A-AUT convient pour 6 applications: Electricity Meter with Segment LCD, Water and Gas Meter with LCD Display, Battery-Powered Medical Monitor, Industrial Sensor Node with USB Diagnostics, Wearable Health and Fitness Device, IoT Edge Node with LCD Status Display.
Electricity Meter with Segment LCD
The ATSAML22N17A-AUT is purpose-built for single-phase and three-phase electricity meters where the integrated segment LCD controller drives up to 320 segments for kWh, voltage, current, and tariff readouts. With 39 uA/MHz active current and 490 nA backup, it sustains 10+ years of battery or capacitor-backed operation. The Cortex-M0+ core runs metering algorithms and the integrated 12-bit ADC samples voltage and current channels. The same 100-pin TQFP footprint supports family migration to ATSAML22N18A-AUT for added Flash headroom.
Recommandé
Water and Gas Meter with LCD Display
The ATSAML22N17A-AUT drives a 4- or 8-compartment mechanical register through its segment LCD peripheral and counts pulses from a reed switch or Hall sensor via a GPIO interrupt. The 490 nA backup mode with RTC retains time and consumption data during primary cell replacement. 128 KB Flash fits wireless M-Bus or LoRaWAN stacks when paired with an external transceiver. The 100-pin TQFP provides ample GPIO for tamper switches, optical interfaces, and valve control outputs.
Recommandé
Battery-Powered Medical Monitor
The ATSAML22N17A-AUT suits portable medical devices such as glucose meters, pulse oximeters, and body temperature monitors where battery life and a clear numeric LCD display are essential. Its 12-bit ADC captures sensor data, the segment LCD shows measurement results without a separate driver IC, and the 1.6-3.6 V range accepts direct Li-ion or 2x AA cells. Hardware crypto on the J-variant or AES on the L22J enables secure patient data storage where required.
Recommandé
Industrial Sensor Node with USB Diagnostics
The ATSAML22N17A-AUT integrates a full-speed USB device that engineers can use for firmware update and diagnostic logging without an external bridge IC. In industrial 4-20 mA sensor heads, the 12-bit ADC and multiple SERCOM channels (I2C/SPI/UART) connect to MEMS sensors and isolated transceivers. The wide -40C to +85C operating range supports factory-floor deployment, and the 100-pin TQFP provides a rugged leaded package for harsh environments.
Recommandé
Wearable Health and Fitness Device
Wearable step counters, heart-rate monitors, and thermometer watches leverage the ATSAML22N17A-AUT for sub-microamp standby between sensor samples and an integrated segment LCD for time and metric display. The 32 MHz Cortex-M0+ executes BLE stack stubs and HRM algorithms within 39 uA/MHz, while 490 nA backup mode keeps the RTC alive overnight. The 100-pin TQFP package suits small form-factor wearable PCBs where exposed lead reliability matters.
Recommandé
IoT Edge Node with LCD Status Display
IoT edge devices such as smart thermostats, room controllers, and HVAC user interfaces benefit from the ATSAML22N17A-AUT's segment LCD up to 320 segments and multiple SERCOM channels for sensor and radio connectivity. The Cortex-M0+ runs FreeRTOS or ASF firmware, the 128 KB Flash holds TCP/IP and MQTT stacks, and the 1.6-3.6 V range accepts 3.3 V system rails directly. The 100-pin TQFP is convenient for hand-soldered prototypes and production assemblies alike.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATSAML22N17A-AUT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATSAML22N18A-AUT | ATSAML22N16A-AUT | ATSAML22J17A-AUT | ATSAM4LS2CA-AU |
|---|---|---|---|---|---|
| Package | TQFP-100 (14x14) | TQFP-100 (14x14) - same | TQFP-100 (14x14) - same | TQFP-100 (14x14) - same | TQFP-100 (14x14) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M4F |
| Max Clock | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 48 MHz |
| Flash | 128 KB | 256 KB | 64 KB | 128 KB | 128 KB |
| SRAM | 16 KB | 32 KB | 8 KB | 16 KB | 32 KB |
| LCD Segments | 320 | 320 | 320 | 320 | None |
| Active Current | 39 uA/MHz | 39 uA/MHz | 39 uA/MHz | 39 uA/MHz | 90 uA/MHz |
| Backup Current | 490 nA | 490 nA | 490 nA | 490 nA | 1500 nA |
Principaux différenciateurs
- Integrated segment LCD controller with 320 segments (vs ATSAM4LS2CA-AU)
- Sub-500 nA backup mode with RTC retention (vs ATSAM4LS2CA-AU)
- Scalable Flash footprint across the SAM L22 family (vs ATSAML22N18A-AUT)
Notes de conception
Place a 1uF X7R ceramic decoupling capacitor within 5 mm of the VDDCORE pin (pin 99) and a 100 nF X7R within 5 mm of each VDD/VDDIO pair (pins 6, 11, 32, 63, 97). The VDDCORE pin is internally regulated and must not be driven externally. Use a star-ground topology connecting all GND pins to a single copper pour under the TQFP thermal pad to avoid ground bounce during LCD charge-pump switching.
The segment LCD charge pump uses external VLCD and HPM pins; consult the reference schematic in the SAM L22 datasheet section 'LCD Controller'. Using incorrect reservoir capacitor values (< 1uF) on HPM causes ghosting segments. Do not enable the LCD controller before configuring the GPIO mux for SLCD_COM and SLCD_SEG functions, otherwise the segment pins default to GPIO and can drive the LCD glass incorrectly.
Route the USB DP and DM pair (PA24, PA25) as a 90-ohm differential pair with length matching within 2 mm. Place the 27 ohm series damping resistors close to the MCU side and keep the pair away from switching power traces. For PCB layout, fan out the 100-pin TQFP on both sides with 0.2 mm trace width minimum to reach inner escape layers; the 14x14 mm package offers generous routing channels for 4-layer stack-ups.
Informations de conformité
RoHS and REACH compliance per Microchip product page. Industrial temperature grade -40C to +85C; not AEC-Q100 qualified (use ATSAML22N17A-AUT automotive variant for vehicle applications if available).
