BTS3028SDLATMA1 - 5A Low-Side Smart Switch | Infineon
Référence : BTS3028SDLATMA1 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $1.85 | $1,85 |
| 10 | $1.62 | $16,20 |
| 100 | $1.38 | $138,00 |
| 500 | $1.18 | $590,00 |
| 1 000 | $1.05 | $1 050,00 |
BTS3028SDLATMA1 Présentation
A low-side switch is a power switch placed between the load and ground, allowing the load to be grounded on one terminal. Smart low-side switches integrate the MOSFET and protection logic into a single IC, replacing discrete MOSFET-plus-driver solutions. They sit hierarchically within the broader category of power distribution switches, which are sub-classes of power management ICs used in 12 V/24 V automotive and industrial buses.
Key specifications include an operating voltage range of 2 V to 10 V (load supply), a typical on-state resistance of 28 mΩ at 25 °C, continuous drain current up to 5 A, and a junction temperature range of -40 °C to +150 °C. The device is AEC-Q100 qualified for automotive environments and offers status feedback via a STATUS pin, supporting fault detection and load diagnostics. Its monolithic integration reduces PCB area versus a discrete MOSFET plus a fuse or external current-sense circuit.
Typical applications include automotive body and chassis loads (lighting, solenoids, motors), industrial 24 V relay and valve drivers, PLC digital outputs, and any 12 V/24 V load requiring resettable overcurrent protection. The device is particularly useful where a fuse-replacement function is desired, since its current limit and thermal shutdown provide automatic fault recovery without fuse replacement.
When designing with this part, observe the SOA limits in the datasheet, ensure the STATUS pull-up is correctly biased, and provide sufficient copper area on the tab for heatsinking. Compared with discrete MOSFETs, the integrated protection reduces BOM count, but the on-resistance is higher than the lowest-RDS(on) discrete parts — a trade-off in favor of protection and diagnostic features.
This page synthesizes distributor pricing across six channels, drop-in alternatives in the same DPAK footprint, and practical design notes for both automotive and industrial 24 V buses — practical context not found in the manufacturer datasheet alone.
Alternatives de remplacement direct pour BTS3028SDLATMA1 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec BTS3028SDLATMA1 (même facteur de forme et même empreinte) — différant par Package, Operating Temperature Range, Technology, Topology, Continuous Load Current.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
BTS3028SDL
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
BTS452TATMA1
✅ Remplacement direct✓ En stock
$1.12 / unité
Voir la fiche technique →BTS3134NHUMA1
✅ Remplacement direct✓ En stock
$0.78 / unité
Voir la fiche technique →BTS3030SDL
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
BSL215CH6327XTSA1
✅ Remplacement direct✓ En stock
$0.21 / unité
Voir la fiche technique →BSS316NH6327XTSA1
✅ Remplacement direct✓ En stock
$0.13 / unité
Voir la fiche technique →BTS3028SDLATMA1 Valeurs maximales et caractéristiques électriques
| Product Type | Smart Low-Side Power Switch |
| Topologie | 1:1 N-Channel, Single Channel |
| Load Supply Voltage Range | 2 V to 10 V |
| Continuous Drain Current (I_D) | 5 A |
| On-State Resistance (R_DS(on)) | 28 mΩ (typ at 25 °C, V_IN = 5 V) |
| Overvoltage Clamp | Yes (integrated) |
| Overtemperature Shutdown | Yes (integrated) |
| Current Limitation | Yes (integrated) |
| ESD Protection | Yes (integrated) |
| STATUS Feedback Pin | Yes |
| Plage de température de fonctionnement | -40 °C to +150 °C (T_j) |
| Boîtier | PG-TO252-3-11 (DPAK, 3-pin + tab) |
| Type de montage | Surface Mount |
| Automotive Qualification | AEC-Q100 qualified |
| Statut RoHS | Compliant |
Configuration des broches de BTS3028SDLATMA1
| Broche 1 | GND — Ground / source return |
| Broche 2 | IN — Logic-level input (drives gate) |
| Broche 3 | STATUS — Open-drain status feedback |
| Broche Tab | OUT / Drain — Switched output (load return to ground via FET) |
Zone de fonctionnement sûr (DC)
Applications typiques
BTS3028SDLATMA1 convient pour 6 applications: Automotive Body & Lighting Loads, Solenoid and Valve Drivers (24 V Industrial), PLC Digital Outputs, Relay Replacement / Smart Fuse, DC Motor Drive (Small Brushed), LED Driver Low-Side Switch.
Automotive Body & Lighting Loads
The BTS3028SDLATMA1 is designed for 12 V/24 V automotive body and chassis loads such as lamps, LED drivers, and small motors. With 5 A continuous current and 28 mΩ R_DS(on), it can drive a pair of 55 W headlamps with low conduction loss. The integrated overtemperature shutdown, overvoltage clamp, and STATUS feedback enable AEC-Q100 qualified ECUs to detect open-load and short-circuit faults without external fuses.
Recommandé
Solenoid and Valve Drivers (24 V Industrial)
In industrial PLCs and process-control boards, the BTS3028SDLATMA1 drives 24 V solenoids, valves, and relay coils. Its 28 mΩ R_DS(on) keeps dissipation manageable at 5 A, while integrated current-limit protection prevents coil-induced transients from destroying the FET. The STATUS pin can signal the PLC CPU when a load is open or shorted, enabling predictive maintenance.
Recommandé
PLC Digital Outputs
As a low-side switch in a PLC digital-output module, the BTS3028SDLATMA1 replaces discrete MOSFET-plus-fuse circuits with a single AEC-Q100 qualified IC. Its 5 A rating covers most 24 V field-side loads, while integrated current limiting and thermal shutdown provide resettable overcurrent protection — eliminating fuse replacement in the field.
Recommandé
Relay Replacement / Smart Fuse
The BTS3028SDLATMA1 functions as a resettable electronic fuse in 12 V/24 V distribution systems. Compared to a traditional fuse, it offers current limiting, thermal shutdown, and STATUS-based fault signaling — all in a single DPAK. This reduces service costs in deployed systems and enables remote fault diagnostics over CAN/LIN buses.
Recommandé
DC Motor Drive (Small Brushed)
For small brushed DC motors (window lifts, seat adjusters, mirror actuators), the BTS3028SDLATMA1 provides a compact low-side drive stage. Its 5 A continuous rating handles typical small-motor stall currents, and integrated protection prevents destruction from locked-rotor events. For bidirectional drive, two BTS3028SDLATMA1 devices in an H-bridge configuration are typically used.
Recommandé
LED Driver Low-Side Switch
The BTS3028SDLATMA1 can switch LED strings in automotive tail-light, daytime-running-light, and interior-lighting modules. With its 28 mΩ R_DS(on) and 5 A capability, it drives LED chains up to roughly 60 W. Integrated protection ensures survival of LED short-circuit faults — a common failure mode in automotive lighting.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour BTS3028SDLATMA1 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | BTS3028SDL | BTS452TATMA1 | BTS3134NHUMA1 | BTS3030SDL |
|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | PG-TO252-3-11 (DPAK) | PG-TO252-3-11 (DPAK) - same | PG-TO252-3-11 (DPAK) - same | PG-TO252-3-11 (DPAK) - same | PG-TO252-3-11 (DPAK) - same |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes | Yes |
| Integrated Protection | OT, OV, CL, ESD | OT, OV, CL, ESD | OT, OV, CL, ESD | OT, OV, CL, ESD + diagnostics | OT, OV, CL, ESD |
| STATUS Feedback | Yes | Yes | Yes | Yes (enhanced) | Yes |
Principaux différenciateurs
- Single-DPAK integrated smart switch with full protection suite (vs Discrete N-channel MOSFET + fuse)
- AEC-Q100 qualified for automotive use (vs Industrial-only low-side switches)
- 28 mΩ R_DS(on) in DPAK for 5 A continuous (vs BSL215CH6327XTSA1 (smaller PG-TSOP-6 package))
Notes de conception
Estimated: at 5 A continuous load and 28 mΩ R_DS(on), power dissipation is approximately 0.7 W, which raises junction temperature by roughly 70 °C above ambient on a standard 1 oz copper DPAK footprint. For sustained operation near 5 A, attach the tab to at least 1 sq inch of copper pour on a 2-layer FR-4 board. Above 100 °C ambient, thermal shutdown may engage — derate current or improve heatsinking accordingly.
Place a 100 nF ceramic decoupling capacitor near the IN pin to suppress logic-supply transients from the gate drive. Use wide copper traces on the OUT/tab to the load, as the full load current flows through this path. Connect the tab to a large copper pour for both electrical and thermal performance — this is the dominant heat-spreading path for the DPAK package.
Do not apply reverse battery voltage directly to the load supply without external protection — the BTS3028SDLATMA1 is not designed for sustained reverse polarity. Add a reverse-battery blocking diode or use Infineon's higher-voltage HITFET variants (e.g., BTS3134NHUMA1) if reverse polarity is required. Also, ensure the STATUS pull-up is rated for the load-supply voltage; tying it directly to a 5 V logic rail when the load is at 10 V can damage the open-drain transistor.
Informations de conformité
RoHS compliant and AEC-Q100 qualified per Infineon product page. Lead-free and halogen-free per PG-TO252-3-11 package documentation.
